| Age | Commit message (Collapse) | Author |
|---|
|
Device 1 on secondary bus instead of device 0 was being routed.
Change-Id: I4207938038acf7ff941afd692e90a690d2426a05
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16515
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I389c4630362af1c1bf6d281c9d2b7fc81bea2d5d
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16495
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is necessary for PCI express graphics card add-ons,
otherwise the pci allocator cannot fit the mmio for the
add on card into the space it has available and the OS
turns off the card. Old value was 1GiB.
Change-Id: I606994501b15e636fe209d1ed4b3d3f73b42bf5c
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16494
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
No more hang on DMI init when wait for DMI is re-enabled.
Previously the virtual channel arbitration table was not being
set up in the south/north bridges causing invalid DMI state.
This has been tested on GA-G41M-ES2L with patches following.
An NVIDIA GT218 card was detected by the OS and displayed using
the nouveau driver with no blobs.
Change-Id: I35e03c40f5f7aa4915afd5d26db7ab053abcf0cd
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16491
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
According to "G45: Volume 3: Display Register
Intel ® 965G Express Chipset Family and Intel ®
G35 Express Chipset Graphics Controller" some registries
are set incorrectly in gm45/gma.c.
Some values are changed after comparing them with the values
the i915 linux kernel (3.13 was used) module sets while modesetting.
The values were obtained using 'intel_reg' from intel-gpu-tools,
during a normal boot and with 'nomodeset' as a kernel argument.
Some registers that don't exist on gm45 are set in gma.c, which is
probably the result of copying code from a more recent intel
northbridge.
The result is that that gm45 laptops with wxga displays still work as
before. gm45 laptops with wxga+ or higher resolution now just work,
where previously a black screen was shown.
TEST: build with native graphic init and flash on a gm45 target, like
lenovo x200.
Change-Id: If66b60c7189997c558270f9e474851fe7e2219f1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16217
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Remove an unusued function declaration that caused problems while
compiling the target.
Change-Id: Idfd73693e9b0e1777cafa4706113fde394e95795
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16435
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Replace the use of the old device_t definition inside
northbridge/intel/i945.
The patch has been tested both with the arch/io.h definition of
device_t enabled and disabled in order to ensure compatibility
while the transaction takes place.
Change-Id: I041c150a7b50261e26955ad9287ef05b9a06e412
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16371
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Replace the use of the old device_t definition inside
northbridge/intel/sandybridge.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: I35cc76ec7b6baa216666d06f6f325f43ac69067e
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16409
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I53208ce5db06d2c65f954e6d59222924ab87722e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16304
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ic85f725bbdf72fbac5a4d9482c61343c5eb35e25
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16305
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ic644cf6792a5d360527e48e04c74ae92be0d1d4f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16284
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
On i945 the vram size is the default 8mb. It is also possible
to set it 1mb or 0mb hardcoding the GGC register in early_init.c
The intel documentation on i945, "Mobile Intel® 945 Express Chipset
Family datasheet june 2008" only documents those three options.
They are set using 3 bits. The documententation also makes mention
of 4mb, 16mb, 32mb, 48mb, 64mb but not how to set it.
The other non documented (straight forward) bit combinations allow
to change the VRAM size to those other states.
What this patch does is:
- add those undocumented registers with their respective vram size to
the i945 NB code;
- make this a cmos option on targets that have this northbridge.
TEST: build, flash to target, set cmos as desired and boot linux.
On Debian it can be found using "dmesg | grep stolen".
NOTE: dmesg message about reserved vram are quite different depending
on linux version
Change-Id: Ia71367ae3efb51bd64affd728407b8386e74594f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/14819
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I6a533667c7c8ff5ec6ab9d4e1cfc51e993a90084
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16280
Tested-by: build bot (Jenkins)
Reviewed-by: Omar Pakker
|
|
This allows to set the preallocated memory for the IGD on x4x
using a cmos option.
If no cmos option is found a default value of 64M is used.
TESTED most options on ga-g41m-es2l with 2G dimm in one slot and 2x2G.
352M also works in contrast with gm45 where it is known to cause issues
with certain ram combinations.
Change-Id: I9051d080be82f6dfab37d353252e29b2ed1fca7f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/15492
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The Intel documtentation, "Intel ® 4 Series Chipset Family"
mentions the possibility of 1, 4, 8 and 16M of preallocated
memory for the IGD, but does not document this.
This allows to set those undocumented values.
TESTED on ga-g41m-es2l with 2G dimm in one slot and 2x2G.
Change-Id: I92beb8d78907d4514a5aaf69248dd607dcf227c0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/15491
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
if (gart) { foo = gart?a:b; } never evaluates to foo=b.
Change-Id: Ibc7376687374065585b125a670dea5fe46bda97a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1347365
Reviewed-on: https://review.coreboot.org/16008
Tested-by: build bot (Jenkins)
Reviewed-by: Omar Pakker
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
These non-ascii & unprintable characters aren't needed.
Change-Id: I129f729f66d6a692de729d76971f7deb7a19c254
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15977
Tested-by: build bot (Jenkins)
Reviewed-by: Omar Pakker
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I7930d5cded290f2605d0c92a9c465a3f0c1291a2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15974
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I5aa27f06f82a8309afb6e06c9e462e5792aa9986
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/15940
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
With VBOOT_VERIFY_FIRMWARE separated from CHROMEOS, move recovery and
developer mode check functions to vboot. Thus, get rid of the
BOOTMODE_STRAPS option which controlled these functions under src/lib.
BUG=chrome-os-partner:55639
Change-Id: Ia2571026ce8976856add01095cc6be415d2be22e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15868
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Now hardcode maximum memory frequency capability to 800MHz, as
all chipsets in x4x family support PC2-6400 according to the datasheet.
CAS latency detection also relies on this, and has been cleaned up.
Ram initialization does not work with FSB 1333MHz / DDR2 800MHz combination,
so disable this combination for now, and reduce to 667MHz instead.
Still don't know why this is the case, but FSB1333/667 works.
These changes should now allow existing configurations to continue working,
while providing support for previously unworking configurations, due to
previous buggy CAS latency detection code.
TESTED: on GA-G41M-ES2L
CPU: E5200 @ 2.50GHz (FSB 800MHz)
2x 1GB 667MHz hynix worked @ 667
1x 2GB 800Mhz ARAM worked @ 800
1x 1GB 667Mhz StarRam worked @ 667
2x 2GB 800Mhz (generic) worked @ 800
Change-Id: I1ddd7827ee6fe3d4162ba0546f738a8f9decdf93
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/15818
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Match the definition and use of these variable with haswell, such that
DCACHE_RAM_MRC_VAR_SIZE is not included in DCACHE_RAM_SIZE.
Change-Id: I5af20f63cd0cb631d39f7c7fe0e2a99ebd3ce986
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15761
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Fix and use the failsafe CAS detection logic rather than
recalulating the values from raw SPDs.
Tested on GA-G41M-ES2L with 2x2GB DDR2-800 DIMMs
(which worked before and still work)
Change-Id: I6af0f1705d099f7bcbff8c9baa94a68dae689e01
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/15726
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
If S3 support was implemented for this platform later on, use
romstage handoff structure instead.
Change-Id: I03c1e07a7fcc17c27203d0c4e32e3958f2ba5273
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15716
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Damien Zammit <damien@zamaudio.com>
|
|
If S3 support was implemented for this platform later on, use
romstage handoff structure instead.
Change-Id: Ib0cf3ad41753baee26354c5ed19294048e7fb533
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15715
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Damien Zammit <damien@zamaudio.com>
|
|
Change-Id: Ie120360fa79aa0f6f6d82606838404bb0b0d9681
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15466
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I7c3973ff325f11a86728e8660c70839776981aa5
Reported-by: GCC 6.1.0
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/15554
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Previously, any 800MHz DIMMs were being slowed to 667MHz
for no reason other than there was a bug in the maximum
frequency detection code for the MCH.
Change-Id: Id6c6c88c4a40631f6caf52f536a939a43cb3faf1
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/15257
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Reading cpuid leaf 0 is incorrect for testing cpu family.
Use leaf 1 instead. See Intel SDM 2a Table 3-17.
Change-Id: Ib2c95cdd1fb93db06a08ecd7266f6b88700caf83
Signed-off-by: Ryan Salsamendi <rsalsamendi@hotmail.com>
Reviewed-on: https://review.coreboot.org/15346
Tested-by: build bot (Jenkins)
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Change-Id: I6f0cdc80870fddeaada3191e493bd85fdefee07f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15245
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Broken with commit:
5c10abe nb/intel/sandybridge: increase MMCONF_BASE_ADDRESS
Available sandybridge/systemagent-r6.bin has MMCONF hard-coded
at some places and samsung/lumpy fails at boot here:
CBFS: Locating 'mrc.bin'
CBFS: Found @ offset 9fec0 size 2fc94
System Agent: Starting up...
System Agent: Initializing
These are the last lines as captured over USB debug.
Change-Id: I441847f0e71a5e1be9c8ef6a04a81eb7bdd8a6d9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15328
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Without RELOCATABLE_RAMSTAGE have WB cache large enough
to cover the greatest ramstage needs, as there is no benefit
of trying to accurately match the actual need. Choose
this to be bottom 16MiB.
With RELOCATABLE_RAMSTAGE write-back cache of low ram is
only useful for bottom 1MiB of RAM as a small part of this gets used
during SMP initialisation before proper MTRR setup.
Change-Id: Icd5f8461f81ed0e671130f1142641a48d1304f30
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15249
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ib3250677ee926deaa957c83aca7479eb0159358c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15231
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Instead of programming unsupported CAS use the highest supported
value. Start at DDR3 maximum of CAS 18T.
Increase error message verbosity level.
Useful for overclocking.
Tested on Lenovo T520 and DDR3-1600 DIMM (RMT3170eb86e9w16).
Allows to run a DDR3-1600 DIMM at 933Mhz.
Change-Id: I2e8aadd541f06fa032ad7095c9a2d5e3bb7613f3
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15217
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Calculate the value from current DDR frequency.
Tested on Lenovo T520 and DDR3-1600 DIMM (RMT3170eb86e9w16).
Change-Id: I57ffbfeb291fc2fede278d18527993e7432e9bd8
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15184
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Simplify calculation of value.
Tested on Lenovo T520 and DDR3-1600 DIMM (RMT3170eb86e9w16).
Change-Id: I3ecd12c431b46a8d2218f33d7eb3e10de3bcd61d
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15181
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Set max_mem_clock_mhz in devicetree to 933Mhz.
Allows to run the memory at up to DDR3-1866.
The same frequency was allowed within the first vendor bios,
but Lenovo than decided to limit it to DDR3-1333.
Tested on Lenovo T520 and DDR3-1600 DIMM (RMT3170eb86e9w16).
The RAM is now running at DDR3-1600 instead of DDR3-1333.
This gives about 4% performance increase in glmark2 using the
Intel GPU.
Change-Id: If15be497402d84a2778f0434b6381a64eda832d6
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15158
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I3c517fc55dd333b1a457324f1d69aeb6f70acec2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15197
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
|
|
This is more of ACPI S3 resume and x86 definition than CBMEM.
Change-Id: Iffbfb2e30ab5ea0b736e5626f51c86c7452f3129
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15190
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Instead of hardcoding the PCI mmio size read it from devicetree.
Set a default value of 2048 MiB and 1024MiB for laptops without
discrete graphics.
Tested on Sandybridge Lenovo T520.
Change-Id: I791ebd6897c5ba4e2e18bd307d320568b1378a13
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15140
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Remove code duplication and use the common function
store_current_mrc_cache instead.
No functionality is changed.
Tested on Sandybridge Lenovo T520.
Change-Id: I4aa5463f1b1d5e1afbe44b4bfc659524d86204db
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15074
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Previously, 0x0 was the value being used for an unpopulated dimm
on spd[62], however some DDR2 dimms have 0x0 as a valid value.
Now use 0xff which is an unused value even on DDR2/DDR3.
Change-Id: I55a91a6c3fe3733a7bb2abc45ca352c955c07c99
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/15058
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Setting the size of the preallocated memory for the igd is done
using a cmos parameter, gfx_uma_size. This was limited to a subset of
all available sizes, that were already implemented elsewhere
in the northbridge code.
What this does is change the cmos parameter to 4 bits instead
of 3 bits to accomodate all vram sizes.
It also adds a sane default of 32mb that already was in place.
The northbridge code that reads this cmos parameter is
also changed for this new cmos settings.
352M is disabled since it causes issues on systems with 4GB or more ram.
TEST: Build, flash target. Clear cmos by corrupting
the checksum (nvramtool -c something).
Set a desired value in gfx_uma_size using nvramtool.
"dmesg | grep stolen" to see what is actually allocated.
Change-Id: Ia6479d03f1abe6d0c94bd7264365505e8f8eaeec
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/14900
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The declarations of CFG_ evaluate to correct values only when
included after the definitions of BLDCFG_ in buildOpts.c.
So we never have CFG_PLAT_NUM_IO_APICS defined here.
Change-Id: I94b3dee5a3207b37921eb24a0bcd73b5a217b2d3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14887
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The values were obtained from vendor bios at runtime.
I am not 100% sure of the sequence required to initiate them,
but guessed from the gm45 code. There may be some status bytes
needed to be polled during the sequence that is missing,
but as I don't have bios writer's datasheet it's very hard
for me to know.
Change-Id: Idd205e0bab5f75e01c6e3a5dc320c08639f52db8
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/14925
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Items under DEVICE_SPECIFIC_OPTIONS got selected without
the driver being selected.
Change-Id: I1797fa6175620a9291873559a6308eaea85a090e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14823
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I6ea9b9d2353c0d767c837e6d629b45f23b306f6e
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14599
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
|
|
The existing DIMM size calculation for DDR3 was incorrect. Use
the recommended calculation from the DDR3 SPD specification.
Change-Id: Id6a39e2b38b5d9f483341ebef8f2960ae52bda6c
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14739
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
While some stubs existed before this patch to handle non-ECC
memory initialization, there were a number of ECC detect unaware
sections of code. Add ECC support detection to those sections.
Change-Id: I56dad8a0f6833b2f42796212afb9777e9cc73d6d
Tested-On: ASUS KGPE-D16
Tested-With: 1x Opteron 6262
Tested-With: 1x SuperTalent 4G non-ECC DIMM in slot A2
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14737
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Damien Zammit <damien@zamaudio.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Mask out the bit that doesn't fit in 32bits, so gcc 6.1 is happy
Change-Id: I13e2b41742206b8d86b90314b80cc324c00ae637
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14639
Reviewed-by: Damien Zammit <damien@zamaudio.com>
Tested-by: build bot (Jenkins)
|
|
gcc 6.1 complains that SMM_OFFSET << 8 is larger than the register
it is assigned to (rightly so):
src/northbridge/amd/gx2/northbridgeinit.c:196:23: error: result of
'1077936128 << 8' requires 40 bits to represent, but 'int' only
has 32 bits [-Werror=shift-overflow=]
msr.lo = (SMM_OFFSET << 8) & 0xfff00000;
^~
Change-Id: Ib0d669268202d222574abee335a6a65c8a255cc7
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14617
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I99e5d7f3b46c90ca863ddf6c186b5447d0c8e6f2
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14607
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I16c04452d2d6c3205aea29fe8aa8fad8fc485a46
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14600
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The PLL will never lock if the requested frequency is already set.
As the fallback may request the same frequency again exit early
to prevent a hang.
Test system:
* Gigabyte GA-B75M-D3H
* Intel Pentium CPU G2130
Change-Id: I625b2956346d8c50cca84def6190c076bf99dbec
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14174
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add the following fallbacks:
* Try decreasing clock frequency.
In case of DDR1600 the next possible value of DDR1333 is being used.
* Try decreasing clock frequency.
In case of DDR1333 the next possible value of DDR1066 is being used.
* Disable failing channel.
The system may be able to boot with a single channel enabled.
The fallbacks are untested.
Change-Id: I3be7034ad25312b3ebf47a54f335a3893f8d7cc1
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14173
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The LVDS port is configured to accept data from pipe A, but the panel
fitter and VGA were attached to pipe B.
Changes to VGACNTRL:
- select pipe A instead of pipe B.
- disable VGA centering to fix jitter.
TEST=Build and run on Thinkpad X200 in both text and framebuffer modes.
Change-Id: I2356f264580d8b021952c217de3477291d866f98
Signed-off-by: Nick High <nhigh@openmailbox.org>
Reviewed-on: https://review.coreboot.org/14524
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
The ECC check bits of all ECC DIMMS were inadvertently initialized
twice in the same routine, significantly delaying startup. Part
of this was related to an obsolete MCA workaround that has been
fixed through multiple commits, therefore the workaround is no
longer needed.
Only initialize the ECC check bits once.
Change-Id: I90ac1147d9b006794d29b866a9cb5b7ead8f01e7
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14503
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Idb948acd1a508379f600fbd2fd40fb26b7571d7c
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14545
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
During receiver enable cycle training on Family 15h the entire range
of possible delays is searched, even though the single passing window
is often found nearly immediately. Skip the remainder of the delay
range after the passing window has been located.
Change-Id: If98217fa8e7de77366762d3c7bb01049a1dc080f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14544
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
During DQS receiver enable cycle training on Family 15h platforms the
read data timing registers were inadvertently set to zero on every
lane training attempt.
Ensure that the read data timing registers are correctly set after
each lane is trained in receiver enable cycle training. This allows
more than one RDIMM to function on a given DCT channel.
Change-Id: I87d732f0383e9785a73b57e6f48855f3e872f1f9
Tested-On: ASUS KGPE-D16
Tested-With: 1x Opteron 6262HE
Tested-With: 4x Crucial 36KSF1G72PZ-1G6M1 (slots A2 / A1 / B2 / B1)
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14543
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I1f5b024606093dc81de3f3d69b7a43e20141b709
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14542
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The existing Family 15h receiver enable training code stored
temporary delay values in the wrong variables, leading to
the requisite averaging of delays across nibbles not being
applied. This in turn made x4 DIMMs less stable than they
should have been.
Store temporary nibble delay values in a dedicated array.
Change-Id: Ic5da898af7d689db4110211f89b886ccdbb5f78f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14541
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix regression introduced by:
Ib48fe8380446846df17d37b22968f7d4fd6b9b13
Don't run channel_test on S3 resume as it overrides memory
that might be in use.
Fixes MCE events reported by the GNU/Linux kernel that
low memory has been modified.
Reset on failed s3 resume.
Change-Id: Ibadea286619c7906225f86a93aaa0b4caf26cabe
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14439
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
DIMM training can sporadically fail due to external influences or various
errata. In these cases, restarting to retry training is a more appropriate
response than halting the system and requiring manual intervention.
Change-Id: Id49f7419f56e0640a84448cc06ecbaf62bed145e
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14529
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The wrong DIMM number was used in the initial non-target MRS
setup routines. This had no functional impact other than to
print the wrong DIMM number in the DDR3 verbose debug output.
Change-Id: I480118ed00e1786a06e641a56f0fb19cd87f92eb
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14501
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The existing RDIMM RC control word send routines were a hodgepodge
of various AGESA chunks with different ways of handling the same
task. Unify the control word chip select setup, use precise timing
routines on Family 15h, fix a couple of incorrect masks, and add
additional debugging statements.
It is believed that this patch is cosmetic and does not significantly
alter existing functionality.
Change-Id: Ie4ec7b6a7be7fce09e89f9eec146cc98b15b6160
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14500
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
When more than one DIMM is installed on a DCT, only the first DIMM
delay values are scaled to the new memory clock frequency after a
memory clock change during write leveling.
Store the previous memory clock of each DIMM during write leveling
to ensure that every DIMM has its delay values rescaled.
Change-Id: I56e816d3d3256925598219d92783246f5f4ab567
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14479
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
After substantial testing it has been determined that it is neither
required nor safe to disable the DRAM MCA during initial startup.
This (mostly) reverts commit c094d9961144871c472698c41ce634e58abb6a32.
The minor debugging enhancements from that commit were left in place.
Tested-On: ASUS KGPE-D16
Config-CPU: 1x Opteron 6262HE
Config-RAM: 4x Crucial 36KSF1G72PZ-1G6M1
Config-RAM: 1x Kingston 9965516-483.A00LF
Change-Id: I58fcc296b8c45ecaedf540951c365e4ce52baaf5
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14446
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I5056cf885b7063a97c095bfaaf01dd8da777a425
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14447
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Certain RDIMMs have inherently large write levelling delays,
in some cases exceeding 1.5 MEMCLK. When these DIMMs are
utilized, the phase recovery system requires special handling
due to the resultant offset exceeding the phase recovery reporting
capabilities.
Fix an old error where delays > 1.5 MEMCLK were not being programmed
(gross delay high bit was not in set range), and restore special
delay handling for delays greater than 1.5 MEMCLK.
Also enhance debugging for x4 DIMMs around the affected code.
Tested-On: ASUS KGPE-D16
Config-CPU: 1x Opteron 6262HE
Config-RAM: 4x Crucial 36KSF1G72PZ-1G6M1
Change-Id: I0fb5454c4d5a9f308cc735597607f095fe9188db
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14441
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The BKDG requires phy fences to be re-trained after a memory clock change.
Memory training on the ASUS KGPE-D16 and KCMA-D8 somehow "mostly" worked
-- without actually following this requirement -- !
Fix the single typo that caused several weeks of delay in putting
servers with Kingston RAM (and others) into production...
Tested-On: ASUS KGPE-D16
Config-CPU: 1x Opteron 6262HE
Config-RAM: 4x Crucial 36KSF1G72PZ-1G6M1
Change-Id: I197e6728d2b0ac8c1535740599459d080b17af33
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14445
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We never define B1_IMAGE or B2_IMAGE. These are about building
CIMx as separate binary modules, while coreboot builds these into
same romstage or ramstage module.
Change-Id: I9cfa3f0bff8332aff4b661d56d0e7b340a992992
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14393
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Kerry Sheh <shekairui@gmail.com>
|
|
Reorder drivers to fit src/drivers/[X]/[Y]/ scheme to make
them pluggable.
Also, fix up the following driver subdirectories by switching
to the src/drivers/[X]/[Y]/ scheme as these are hard requirements
for the main change:
* drivers/intel
* drivers/pc80
* drivers/dec
Change-Id: I455d3089a317181d5b99bf658df759ec728a5f6b
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14047
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
gcc doesn't like these because they're undefined behavior, so use
zeroptr instead. For the loop that just does a number of writes (0..4),
use zeroptr + i.
Checked the disassembly (AMD_RUMBA and PCENGINES_ALIX2D) to not contain
ud2 anymore and to look reasonable where zeroptr was used.
Change-Id: I4a58220ec9a10c465909ca4ecbe5366d0a8cc0df
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/14345
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Trivial; Use tab over space for indent. Clean up some ASCII art
while here.
Change-Id: Id2478d140a98596c5eeefdf5b047c1ca23203909
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: https://review.coreboot.org/8016
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Two of the MCT data structures passed as substructures to ramstage were
not packed, and additionally no alignment was specified. On at least
SP5100-based platforms, specifying packed with no alignment caused boot
failure dependent on the exact compiled binary layout (LPC hang).
Specifying the alignment and packing the remaining structures appears to
have resolved the remaining LPC hang issues on the KGPE-D16. Note that
packing the remaining structures alone was not sufficient to eliminate
the hang, however removing the packed attribute entirely (during debugging)
did resolve the hang at the expense of potential problems in ramstage.
Change-Id: If3a7509ed438870d4d05caaaaa091e1c47bf9b97
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14303
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
|
|
The SPI controller needs to be set up on devices such as the SP5100
before it can be accessed to write MCT backup data. Move the backup
data write after PCI configuration has been completed.
Change-Id: Ibcf31755242ac058407a422ce8aa33d6b0b293c7
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14305
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Always use MRC cache if possible.
Added a CRC16 array to make sure the DIMMs haven't been replaced.
In case one of the CRC's doesn't match, start normal RAM training.
Use new fallback in case of broken mrc cache.
Test system:
* Gigabyte GA-B75M-D3H
* Intel Pentium CPU G2130
Test result:
The system boots a lot faster using the MRC cache.
On swapping DIMMs the CRC16 doesn't match and normal ram training
is started.
Change-Id: Ib48fe8380446846df17d37b22968f7d4fd6b9b13
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14172
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This reverts commit f961becc433bf23fc8744fdfd757f0cdb75c2c62.
On studying the BKDG more closely this is not the correct place
to enable DIMM parity. Further patches to clarify the parity
setup process on Family 15h are forthcoming.
Change-Id: I5a3a4f1621e3048f9dfc159709410be9de6ebecd
Reviewed-on: https://review.coreboot.org/14271
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The sync flood reset fix in Change-Id: I62d897010a8120aa14b4cb8d096bc4f2edc5f248
and related changes have made it possible to move the sync flood enable statements
back into romstage.
Change-Id: I5a3a4f1621e3048f9dfc159709410be9de6ebece
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14270
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
When a fatal error and subsequent sync flood / reset occurs,
the MCA status registers may contain valuable information on
the cause of the fatal error. Add functions to report MCEs and
reset the MCA status registers early in the boot process.
Change-Id: Icde1051ac22f93688de1330f5e2c9ce28b14b59a
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14265
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I42d901ae9445943a863fb3ba9bda5a915f255e02
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14264
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Certain AMD platforms, such as those using the SP5100 southbridge,
contain a very poorly documented bug related to LPC ROM access,
which is triggered by repeated (hundreds or more) rapid calls to
get_option(). This bug manifests as a complete system deadlock
in ramstage device configuration, requiring standby power to be
removed from the system to release the deadlock.
Cache the platform ECC status to avoid repeated calls to get_option()
in the lane count detection logic.
Change-Id: I8b48c523218ccc8c113319957d6eca2d15e1070f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14273
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
In error case die in top level function.
No functionality is changed.
Change-Id: Ie15b01184d40bdbce20d49dcab2f9fb607068c7a
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14171
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Return errors to top level ram init function.
Required by the folowing series to implement a fallback.
No functionality is changed.
On error case the system still halts in every test.
Change-Id: I6278c4a1d7b4a96be8988a60671fc3d72cd6cb3d
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14170
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The revision mask for all DR-* series processors was incorrectly
set to only include the DR-B revision mask. Include all DR-*
series prcessors in the DR_ALL revision mask.
Change-Id: Iceda96aa6267b24abcbf78d39f4848d2be8053b8
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Found-by: Coverity, CID 1229627 (#1 of 1): Logically dead code (DEADCODE)
Reviewed-on: https://review.coreboot.org/14216
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
Enabling sync flood on DRAM MCE directly after ECC clear can
lead to a system hang with no way to determine the offending
DRAM module. Clear MCEs after ECC setup, but do not enable
sync flood until NB setup in ramstage to allow time for any
MCEs to accumulate in the status registers. Before enabling
sync flood on MCE, determine if any MCEs were logged during
ramstage execution and display them on the serial console.
Also clear the DRAM ECC sync flood bits during DRAM training
and initial ramstage execution.
Change-Id: Ibd93801be2eed06d89c8d306c14aef5558dd5a15
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14192
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
During power on from cold (S5) state, numerous MCEs are generated
before DRAM training starts, e.g. during HT link training. Clear
these MCEs before DRAM training start, and report any MCEs generated
during DRAM training.
Change-Id: I7d047571242e5bd041e4aac22c1ec1d7d26ef0e6
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14191
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
On Family 15h processors, with certain RDIMMs, MCEs are generated
as a normal part of DCT startup / DRAM training. Disable sync
flood on parity or UC data error until ECC has been enabled.
Change-Id: Ife54751ff127ffd59baaad35d3fea14ea01ef505
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14186
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This resolves a long-standing issue with RDIMM control word
configuration failure, likely due to random parity failure.
Change-Id: If8b8dc5b8b99f4c2fe29b3a133b064631e4693be
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14184
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I96d695ed10176276116fcf3a2b77605fb3f2d5db
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13710
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
In order to add a fallback mechanism, move the ram training code
into a new function. This function will be called multiple times
and must return error or success to the calling function.
Change-Id: I5ee1b3a528290d8252d236b9152b81291736958a
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14169
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
It's required to store the dimm_info in ramctr_timing as only ramctr_timing
is written to mrc cache.
Allows to fill SMBIOS type 17 if mrc cache is used.
Change-Id: I7634b05069df307d471938d9854997a018de81b3
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14168
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Replace open coded memset() functions with calls to the library function.
The new code also explicitly backs up and restores the data structures
that are preserved across calls to mct_ResetDataStruct_D(), and no longer
relies on structure member order to function correctly.
Change-Id: I6dd6377deda0087cd1b65f7555588978657d6516
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14165
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ic5482dc13ab7b53ec4df408bbe32d20888ae2e12
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13725
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
During maximum read latency training on Family 15h processors,
the maximum read latency was incorrectly set from the NBP1
value instead of the correct NBP0 value.
Modify maximimum read latency training to explicitly operate
on the NBP0 value, and store the previously calculated NBP1
value for reference by other portions of the training algorithm.
Change-Id: I5d4a6c2def83df3e23f1a4c598314c31a0172cd7
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14150
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
|
|
dqsTrainMaxRdLatency_SW_Fam15()
Change-Id: Ic3f636983cf6ba2796ee56e2a25b56513a4343c1
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14148
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Under certain conditions (training abort) BlockRxDqsLock could
remain set in violation of the BKDG. Ensure BlockRxDqsLock is
reset to 0 after a lane training abort.
Change-Id: I1a49a24d02b2b7cacae074794ec274a424a9e66b
Reviewed-on: https://review.coreboot.org/14144
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The Intel i3100 northbridge code is the only user of
cache_ramstage(). Therefore, place it next to the sole
consumer.
Change-Id: If15fb8d84f98dce7f4de9e089ec33035622d8f74
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14097
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Rebasing change I3be808db5d15ceec4c36d17582756b01425df09a
did not take into account the default UI setting introduced in
change I6ae88c891e92b21dc0ca3c47b8f3d269f83b3204 , causing DRAM
instability and occassional failure to boot.
Use the correct 1UI value for the modified function semantics.
Change-Id: I9fd24cf83e4c4083c6e467d49021c98e5f5f2c53
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14073
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
