| Age | Commit message (Collapse) | Author |
|---|
|
This is purely cosmetic. All error messages in the Sandybridge raminit
code printed a newline at the end.
Change-Id: I880d291928291d487039850a2a3d53a1101124ba
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1699
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Each G34 socket has two node. Previous lapic algorithm is written for
the CPU which has one node per socket. I test the code on h8qgi with
4 family 15 CPUs(8 cores per CPU). The topology is:
socket 0 --> Node 0, Node 1
socket 2 --> Node 2, Node 3
socket 1 --> Node 4, Node 5
socket 3 --> Node 6, Node 7
Each node has 4 cores.
I change the code according to this topology.
Change-Id: I45f242e0dfc61bd9b18afc952d7a0ad6a0fc3855
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1659
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
This will allow the lower bank to be cleared without impacting the
ability to suspend/resume.
Change-Id: Iaec3c9e7e40c334053c814eaddd1f614df245a73
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1696
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
PCIE devices are detected and initialized by the AMD PCIe init functions,
which is in cimx rd890. The parameters are read from devicetree.cb before PCIe init.
Now, all bridges and devices are trained on the device 0.0 enable.
After PCIe init, the PCIe ports with devices are on and the PCIe ports
without devices are off. so resources may be allocated correctly
during the rest of the PCI scan.
But if the devicetree was being used to enable/disable devices after initialization,
the problems would arise. Take a look at the serial log:
do_pci_scan_bridge for PCI: 00:02.0
PCI: pci_scan_bus for bus 01
PCI: pci_scan_bus returning with max=001
do_pci_scan_bridge returns max 1
do_pci_scan_bridge for PCI: 00:03.0
PCI: pci_scan_bus for bus 02
PCI: pci_scan_bus returning with max=002
do_pci_scan_bridge returns max 2
do_pci_scan_bridge for PCI: 00:04.0
PCI: pci_scan_bus for bus 03
PCI: pci_scan_bus returning with max=003
do_pci_scan_bridge returns max 3
PCI bridge 02.0, 03.0 and 04.0 are not inserted devices, but these bridges
are still scanned. This is not correct.
Change-Id: I87dac5f062c6926081970ed0c5f26a7e3f447395
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1640
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
There are four mainboards using agesa family15 code:
Supermicro h8scm and h8qgi, Tyan s8226 and AMD dinar.
All of these boards' PCI domain starts from 0x18.0. Take h8scm as
an example, PCI devices from 0.0 to 0x14.5 is under 0x18.0.
Now, the PCI domain's scan bus function stats from 0.0. This would
result to the PCI devices be scanned twice. Because when the function
run to device 18.0, it would scan from 0.0 again.
This issue would result to 2 problems:
1) PCI device may be assigned two different PCI address.
If this happenned on VGA device, coreboot maybe not load
vga bios correctly.
2) coreboot initializes rd890's IO APIC twice.
So this patch scans from 0x18.0 and could resolve the problems above.
Change-Id: I90fbdf695413fd24c7a5e3e9b426dc7ca6e128b1
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1639
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Unfortunately the reference tool chain was updated
without ever even testing it on an abuild run. This
broke a number of ports.
This change gets coreboot at least compiling again
for all supported systems.
Change-Id: I92c7cbc834de6d792fdab86b75df339e2874c52e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1670
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Without this, the output of "Setting up ACPI…" continues right
after the output of stepping.
Change-Id: I2ad7cc3e55884ff509600b01274258b8e8250981
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1632
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
I don't know if the size main memory supposed to be in PCI(0,0) reg 0x9c
but it is not written there. The size of memory is written in
src/northbridge/intel/sch/raminit.c to SCH port(2, 8, 4) (look for
"Setting up TOM").
Change-Id: Iea04a5185bda56f61d1c382533d5a0dac429ebbd
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1629
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
The GGC register which contains the size of memory that is used for GPU
is in PCI device 2,0 and not 0,0. It is set to to 4MiB in
src/mainboard/iwave/iWRainbowG6/romstage.c.
Change-Id: Ie9f1cc60544ecd9cad770f34c83c33564a6129d4
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1628
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Without this, the hightables are placed just before the end of memory.
However we might have the GPU memory located at the exact same spot,
that is in the last 4 MiB. So without this patch, this area won't remain
marked as "CONFIGURATION TABLES" within coreboot's memory table but
becomes "RESERVED" because it is part of the PCI(2,0) device.
Change-Id: Ibd111c167c2f6ac03b0ba68581a74ecbd2c9c160
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1627
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
HPET's min ticks (minimum time between events to avoid
losing interrupts) is chipset specific, so move it to
Kconfig.
Via also has a special base address, so move it as well.
Apart from these (and the base address was already #defined),
the table is very uniform.
Change-Id: I848a2e2b0b16021c7ee5ba99097fa6a5886c3286
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1562
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
|
|
Also deletes files not included in build:
src/southbridge/amd/cimx/sb700/chip_name.c
src/southbridge/amd/cimx/sb800/chip_name.c
src/southbridge/amd/cimx/sb900/chip_name.c
Change-Id: I2068e3859157b758ccea0ca91fa47d09a8639361
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1473
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
... but no-one told intel/sch.
Change-Id: I68eaae6910bd6fc579c35b5bc038b9597cd1b3e7
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1537
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
According to http://review.coreboot.org/gitweb?p=coreboot.git;a=blob;f=src/vendorcode/amd/agesa/f15/Proc/CPU/cpuApicUtilities.c;hb=HEAD#l273 line 273,
adjust apic id to accommodate two CPUs.
The Tyan S8226 has two CPU sockets, and the current code just finds one CPU's cores.
we adjust apic_id in cpu_bus_scan so as to find all CPUs.
Change-Id: Ib3263fc6f5508f744b81e8e388fde9ccd9b51851
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1498
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
In commit 6b5eb1cc2d1702ff10cd02249d3d861c094f9118 setup of
UMA memory region was moved to happen at a later state and
this broke UMA with RS780 southbridge.
Share the TOP_MEM and UMA settings before any of the PCI or CPU
scanning takes place.
Change-Id: I9cae1fc2948cbccede58d099faf1dfe49e9df303
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1488
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Factor CPU allocation out of AMD northbridge codes. As CPU topology
information is required for generation of certain ACPI tables, make
this code globally available.
For AMDK8 and AMDFAM10 northbridge, there is a possible case of
BSP CPU with lapicid!=0. We do not want to leave the lapic 0 from
devicetree unused, so always use that node for BSP CPU.
Change-Id: I8b1e73ed5b20b314f71dfd69a7b781ac05aea120
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1418
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Use of alloc_find_dev() prevents creation of a device duplicates
for device_path and is SMP safe.
Reduce scope of variables to make the code more readable and in
preparation for refactoring the allocation out of northbridge.c.
Change-Id: I153dc1a5cab4f2eae4ab3a57af02841cb1a261c0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1186
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The name is derived directly from the device path.
Change-Id: If2053d14f0e38a5ee0159b47a66d45ff3dff649a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1471
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Take a copy of BSP CPU's TOP_MEM and TOP_MEM2 MSRs to be distributed
to AP CPUs and factor out the debugging info from setup_uma_memory().
Change-Id: I1acb4eaa3fe118aee223df1ebff997289f5d3a56
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1387
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This was broken, fixing according to related patch for i945
Change-Id: I925cd205ee5beb918181740a7b981a4209688ac6
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1412
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The includes removed here were previously required for
struct lb_memory and lb_add_memory_range().
Change-Id: Ie6c0d4ef55c2225aa709cf3fbad30ff1080e3610
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1391
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
The function is a noop for all but amd/serengeti_cheetah.
Change-Id: I09e2e710aa964c2f31e35fcea4f14856cc1e1dca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1184
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The names were set at various times during development, but
the way the code works, you might end up with the wrong name
being displayed in the logs. Instead of doing magic, just
display both names for each component
Change-Id: I1f8ce44d156442f5f7d717e1a2b47ed1218d4527
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1413
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Apply the change
http://review.coreboot.org/1263
to family15 northbridge.
Change-Id: If1109f20ffd833a716e092c5e4f6f16ee6b968c7
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
[km: rebased]
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1405
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Apply the change
http://review.coreboot.org/1265
to all the AMD northbridge.
Change-Id: Idf3994c1e9ec76cd19db9f740d825cf24059884f
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1404
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Apply the change
http://review.coreboot.org/1264
to all the AMD northbridge.
Change-Id: Ied74d6f579d2c0350288e2619d7810f8d44fa574
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1403
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The field device in PCI_ADDRESS only takes 5 bits. So if the device number is
more than 32, it will truncated to 5 bits. Before this patch, other pci devices
will be incorrectly probed as processor node.
Change-Id: I64dcd4f4fda7b7080a9905dce580feb829584b94
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1264
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
UMA region can be determined at any time after the amount
of RAM is known and before the uma_resource() call.
Change-Id: I2a0bf2d3cad55ee70e889c88846f962b7faa0c7e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1379
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Without GFXUMA, variables were not referenced anywhere.
Fail builds on Family10 if GFXUMA is selected, because the northbridge
code does not set UMA base or size.
Change-Id: I15b91cf6241e9a890398eed03824b753828a0a51
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1247
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
The code in rs690 or rs780 is always used with K8 or AMDFAM10
northbridge. Without GFXUMA, both of these set the same static value
indirectly using the variable uma_memory_base.
Make the register setting with immediate value, to remove the obscure
use of variable uma_memory_base.
Change-Id: I5354684457a76e73013b4e34a4538a6d122eee8d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1246
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
I dont known if missed something, but why an extra 0x100 was added to limit?
My board would get the wrong memory table entry 7f000000-7fffffff as RAM, which
is higher than TOM.
coreboot memory table:
0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES
1. 0000000000001000-000000000009ffff: RAM
2. 00000000000c0000-000000005e13efff: RAM
3. 000000005e13f000-000000005effffff: CONFIGURATION TABLES
4. 000000005f000000-000000007effffff: RESERVED
5. 000000007f000000-000000007fffffff: RAM
6. 00000000a0000000-00000000afffffff: RESERVED
Ronald G. Minnich:
I think someone who wrote the code was trying to round up the
next 0x100 boundary and did it incorrectly.
Here is code that would do it correctly:
limitk = ((resource_t)((d.mask + 0x00000ff) & 0x1fffff00)) << 9 ;
Zheng:
Plus 0xFF is correct, but the d.mask take bit 0 as enable it.
This bit should be clear when we try to calculate the limitk.
Change-Id: I3848ed5f23001e5bd61a19833650fe13df26eef3
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1265
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Use of uma_resource() in northbridge code created a memory
resource marked as reserved. Such resources are removed
from system memory in write_coreboot_table().
Change-Id: I14bfd560140d8d30ec156562f23072bfae747bde
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1238
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
With SandyBridge northbridge code, uma_memory_size was reset to
zero before variable MTRRs were set. This means MTRR setup routine
did not previously create a un-cacheable hole for uma.
Keep the behaviour that way, mmio_resource() has a prerequisuite that
the new region does not overlap with any cacheable ram_resource().
The result is not optimal setup in the number of used MTRRs, but
continue with this approach until MTRR algorithm is improved.
Change-Id: I63c8df19ad6b6350d46a3eca3055abf684b8b114
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1373
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Reserved memory resources will get removed from memory table at
the end of write_coreboot_table(),
Change-Id: I02711b4be4f25054bd3361295d8d4dc996b2eb3e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1372
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
MRC messes with USB devices, so we have to reinitialize
USB debug after MRC has finished.
Change-Id: I45c0a687cebd69d0a31235bb870f8c455f42d4f2
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1377
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Commit 2d42b340034ff005693482ef9ca34ce3e0f08371 changed the
variable MTRR setup and removed compensation of uma_memory_size in
the cacheable memory resources.
Since the cacheable region size was no longer divisible by a large
power of 2, like 256 MB, this caused excessive use of MTRRs.
As first symptoms, slow boot with grub and poor user response.
As a solution, register the actual top of low ram with ram_resource(),
and do not subtract the UMA/TSEG regions from it.
TSEG may require further work as the original did not appear exactly
right to begin with. To have UMA as un-cacheable, use uma_resource().
Change-Id: I4ca99b5c2ca4e474296590b3d0c6ef5d09550d80
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1239
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Tested-by: build bot (Jenkins)
|
|
No need for the test, tomk is at most 1GB on these chipsets.
Even if there was no room, adjusting the memory resource would not
not divert accesses in the hardware from DRAM to PCI.
Change-Id: I2213b8d9d2e6ab8da8fd3e8081cc62bb05b6b316
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1369
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
No need for the test, tomk is top of low memory and always below 4GB.
Change-Id: Ifc8f29268b761aa9b07b578673236a673f0c70b5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1368
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Our driver infrastructure became more flexible recently.
Make use of it.
These are the low hanging fruits (files with 5 device
variants or more), but there are still lots of files
with less potential for deduplication.
Change-Id: If6b7be5046581f81485a511b150f99b029b95c3b
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1358
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
LX has two values that are usually automatically derived but can
be overridden, that were so far defined in each board's romstage.
These values, along with the toggle to enable override are now
part of LX's Kconfig. For boards that gave values but requested
autogeneration, the values are removed.
Further improvements: Figure out the various fields in PLLMSRlo
and make them sensible Kconfig options (instead of the hex value
it is now)
Change-Id: I8a17c89e4a3cb1b52aaceef645955ab7817b482d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1227
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Otherwise there is a flurry of TDP changes with suspend/resume
as the kernel powers devices off on suspend and brings them
back online in resume.
This also adds a mutex around the TDP operations since it is
split across two methods and can't just rely on being Serialized.
Change-Id: I7757d3ddad34ac985a9c8ce2fc202e2b2dcb2527
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1348
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The required power MSRs are mirrored in MCHBAR so
it is possible to configure TDP at runtime via ASL.
This adds the required fields and a set of methods to
configure "TDP down" and "TDP nominal". It explicitly
does not support "TDP up" at the moment.
PSSS: method is added to assist in searching the _PSS
table for the appropriate entry that corresponds to the
desired max non-turbo ratio.
STND: Set TDP Down from Nominal. This will limit CPU to
the TDP down configuration by sequencing the required
changes in the right order.
STDN: Set TDP Nominal from Down. This will set the CPU
back to nominal configuration by sequencing the required
changes in the correct (reverse) order.
This does not introduce any functional changes and must
be paired with additional changes to be useful.
The current configured TDP can be checked to see that
the transition to/from a desired level is successful.
> mmio_read8 0xfed15f50
0x00 # TDP-Nominal
> mmio_read8 0xfed15f50
0x01 # TDP-Down
Change-Id: I31a2f30cc9d134cc5eee980ae9288ae45e71c6e6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1344
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
2048 * ONE_MB will cause warning,
src/northbridge/amd/agesa/family15tn/northbridge.c:667:50: warning: integer overflow in expression [-Woverflow]
I guess it will change the data type to signed integer.
I think the bit shifting is better.
Change-Id: I823f7ead1f7d622bf653cb3bf2ae2343f5e76805
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1263
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ice4d0202590fca0169dcda2770ca6add166b5c13
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1262
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This maintains a 32bit monotonically increasing boot counter
that is stored in CMOS and logged on every non-S3 boot when
the event log is initialized.
In CMOS the count is prefixed with a 16bit signature and
appended with a 16bit checksum.
This counter is incremented in sandybridge early_init which is
called by romstage. It is incremented early in order notice
when reboots happen after memory init.
The counter is then logged when ELOG is initialized and will
store the boot count as part of a 'System boot; event.
Reboot a few times and look for 'System boot' events in the
event log and check that they are increasing. Also verify
that the counter does NOT increase when resuming from S3.
171 | 2012-06-23 16:02:55 | System boot | 285
176 | 2012-06-23 16:26:00 | System boot | 286
182 | 2012-06-23 16:27:04 | System boot | 287
189 | 2012-06-23 16:31:10 | System boot | 288
Change-Id: I23faeafcf155edfd10aa6882598b3883575f8a33
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1315
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
MRC returns specific error codes; print the according error
message if we know what it means.
Change-Id: Iaaf1512b9d577d4291fccfb94d879043ab5b11b5
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1289
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The count was only incrementing for a wake from S5 and
it was not incrementing in the normal reboot case.
Change-Id: I73bc6db6bd02e6c4677f7e44a5c098c6dcb51747
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1328
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
MCHBAR 0x5f10[7:0] should be set to 0x30 for ivybridge
and 0x20 for sandybridge. Move this code to ramstage
and set it per-chipset.
Power Aware Interrupt Routing is supported in ivybridge,
enable it and set fixed priority.
Boot on ivybridge device and read MCHBAR 0x5f10:
mmio_read8 0xfed15f10
0x30
And verify PAIR is enabled (bit4=1):
mmio_read8 0xfed15418
0x24
Change-Id: If017d5ce2bd5ab5092c86f657434f2b645ee6613
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1303
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Ivybridge B0+ CPUs are capable of supporting multiple TDP levels.
This complicates the default case because now the registers that
were reporting max non-turbo ratio are reporting that value for
the highest possible TDP level.
For now this change just forces everything to use the Nominal TDP
values instead of the higher (or lower) levels.
- When building P-state tables, determine the P[1] (max non turbo)
ratio based on the Nominal ratio if available.
- Set the turbo activation ratio to the Nominal max ratio.
- Mirror the power level settings in new MCHBAR register after
they are written, which happens after BIOS_RESET_CPL is set.
- Set the current ratio to Nominal ratio at boot.
1) Verify that P-state table is generated properly with
P[0]=1801MHz (ratio 0x1C) and P[1]=1800MHz (ratio 0x12)
PSS: 1801MHz power 17000 control 0x1c00 status 0x1c00
PSS: 1800MHz power 17000 control 0x1200 status 0x1200
2) Verify power limits in MCHBAR match PKG_POWER_LIMIT:
> rdmsr 0 0x610
0x800080aa00dc8088
> mmio_read32 0xfed159a4
0x000080aa
> mmio_read32 0xfed159a0
0x00dc8088
3) Verify turbo activation ratio is set to nominal ratio:
> rdmsr 0 0x64c
0x0000000000000012
4) Check that proper ratio was set at boot on one core only:
> grep 'frequency set to' /sys/firmware/log
model_x06ax: frequency set to 1800
model_x06ax: frequency set to 1800
model_x06ax: frequency set to 1800
model_x06ax: frequency set to 1800
Change-Id: I592e60a7740f31b140986a8269dca91b4adbb270
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1304
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
... and don't require it to specify a cache type.
This function is only used on romcc boards, and should go away
(because all boards should be switched to CAR)
Change-Id: Ic32ca3be1afffc773c72c140e88b338d48a0c8ca
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1288
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On systems with socketed CPUs we want to be able to
drop in a Sandy Bridge or Ivy Bridge CPU without recompiling the
firmware. Hence, detect the north bridge dynamically. In order
for this to work, we need Ivy Bridge MRC and coreboot configured
for Ivy Bridge.
Change-Id: I635bef2c61d47d36a3fdd87f8ecb6e69097ba969
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1281
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The function is empty (a left-over from i945) and should be removed.
Change-Id: I91e573b5e37cb9133ea1037aef7e6daf3c292864
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1290
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This lets the SPI driver and the LPC driver know about HM70 and NM70.
Change-Id: Id2f1e0e5586a2f7200b2d24785df3f2be890da98
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1300
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Right now, if we have an unknown PCH, coreboot will print something like
this:
PCH type: Unknown rev id 4
Instead, it should also print the PCI ID of the device, so we can add it
to the list of known PCHes.
Change-Id: Ib0b96e287c36d2895d1287b1734ca13d75e7985a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1287
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This is as per Intel's suggestion on how to display their name strings.
Change-Id: Ie82341305e58baa8041e50a61a11b395fa7d9582
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1298
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
When no valid MRC cache area is found, the mrc_cache data structure
was used without prior initialization. This sometimes caused a long
delay when booting because compute_ip_checksum would checksum up to
4GB of memory.
Change-Id: I6a0ca1aa618838bbc3d042be425700fc34b427f2
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1277
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I153579561f7eed6d4befd74ff39e1a5e778d0e46
Signed-off-by: Walter Murphy <wmurphy@google.com>
Reviewed-on: http://review.coreboot.org/1269
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
- The unneeded poll on non-MT force-wake bit was timing out
and causing the gma_pm_init_pre_vbios() function to exit
early so it was not preparing PM registers properly.
I changed the gtt_poll() calls to not return on timeout
unless it can't proceed so we don't see half-initialized
registers.
- RC6+ (Deep Render Standby) is not working reliably so we
can just enable RC6 in the BIOS and let the kernel decide
if it wants to enable RC6+ later.
This Kernel message is new in kernel 3.4:
[drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
Change-Id: I69d005ba56be8c7684a4ea1133a1d761f7c07acc
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1268
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
It's shut down, but UMA memory is not reclaimed. A later extension
could optionally do the magic register dance that allows initialization
of IGD as secondary graphics device.
Change-Id: I2a92bb71755005b886a8e1825325c678a9991bf2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1252
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Set the default location of hudson firmware to 3rdparty.
Move UMA code from mainboard to northbridge.
Change-Id: I11afea0c7fd04aa84a629dc762704c42baf002df
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1241
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Work around 32-bit overflow with 64-bit multiplication. Calculate
correct CPU frequency.
Change-Id: I86d78f2d70b9f9c62fd4e1e0d765e92e4de83f67
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1254
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
It defaults to true, and isn't disabled anywhere in the tree.
I also couldn't think of a case where it's actually useful.
Change-Id: I126a47625d5294f3cfff225629f2a948a83c9b7e
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1250
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: If131ac9df89080faccd8ed952d6fc019483b5b2e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1237
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
One could not pass a device of type APIC to PCI resource functions.
The correct CPU model specific cpu->ops is set at later time in
cpu_initialize().
Change-Id: Ifa274185e4db3080433c1f07e3a48f2b55c0514f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1180
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Northbridge code incorrectly adjusted the last cacheable memory
resource to accomodate room for UMA framebuffer. If system had
4GB or more memory that last resource is not below 4GB and not
the one where UMA is located.
There are three consequences:
The last entry in coreboot memory table is reduced by uma_memory_size.
Due the incorrect code in northbridge code state.tomk,
end of last resource below 4GB, had not been adjusted.
Incrementing that by uma_memory_size diverts a region
possibly claimed for MMIO to RAM, as TOP_MEM is written.
Since the UMA framebuffer did not have IORESOURCE_CACHEABLE,
it was ignored from the MTRR setup and not set uncacheable.
The setting of TOP_MEM and TOP_MEM2, as well as all the MTRRs,
should be copied from BSP to all APs instead of deriving the data
separately for each Logical CPU.
Change-Id: I8e69fc8854b776fe9e4fe6ddfb101eba14888939
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1217
Tested-by: build bot (Jenkins)
Reviewed-by: Denis Carikli <GNUtoo@no-log.org>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
These boards had identical UMA code:
amd/dbm690t
amd/pistachio
technexion/tim5690
technexion/tim8690
The ones below had whitespace or debug level change
compared to the one above:
kontron/kt690
siemens/sitemp_g1p1
These boards use AMDFAM10 guidelines in code:
asrock/939a785gmh
amd/mahogany
Change-Id: Id7c3f48035727f5847f2d7c3a6e87a3d15582003
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1210
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Following boards had identical code:
advansus/a785e-i
amd/bimini_fam10
amd/mahogany_fam10
asus/m5a88-v
avalue/eax-785e
gigabyte/ma78gm
iei/kino-780am2-fam10
jetway/pa78vm5
Following boards had identical code:
amd/tilapia_fam10
asus/m4a78-em
asus/m4a785-m
gigabyte/ma785gm
gigabyte/ma785gmt
In between the two, only whitespace difference.
Change-Id: Iaa48cc7b0038ebcc81be49219b4fc87670aa9941
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1209
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Following boards had identical code:
amd/inagua
amd/persimmon
The following had only whitespace or debug level changes
compared to ones above.
amd/union_station
amd/south_station
asrock/e350m1
Change-Id: I11ee46e06e1dd510cba551166189ebcaa144464b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1208
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Ieaf284c207f0cd4b2f6b804c52f949c16435d823
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1207
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I5705623f5067823fae5986b3bcde58504a463508
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1206
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Use of the uma_memory_base and _size variables is very scattered.
Implementation of setup_uma_memory() will appear in each northbridge.
It should be possible to do this setup entirely in northbridge
code and get rid of the globals in a follow-up.
Change-Id: I07ccd98c55a6bcaa8294ad9704b88d7afb341456
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1204
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Like ram_resource(), but reserved and not cacheable.
Switch all AMD northbridges to use this one.
Change-Id: I88515c6a0f59f80fd8607c390d0d4a2a35d805f2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1203
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The current code didn't reserve static resource the right way.
Also reduce TOLM to 0xd0000000, because those boards have so many PCI
devices that 0xe0000000 isn't sufficient.
Change-Id: Ia75a81905eea1a096aed464b63ac154e044bc99c
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1220
Tested-by: build bot (Jenkins)
|
|
Don't stop if RAM init fails at first try. It's better to restart
and try again instead of failing on the first try if the second
try would have worked.
Change-Id: Ib5660265d5b10a01588f2e4022dac2ee34f2c6d0
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1191
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I48be647e3f38038830200bcc64429cbf86990ad7
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1174
Tested-by: build bot (Jenkins)
|
|
This is mostly necessary for reboot, but it doesn't hurt the boot process.
On reboot explicitely reset the integrated graphics, otherwise the VGABIOS
might not be able to reinitialize it properly, and you either have a still
of the last pre-reboot image, garbage or an empty screen, but no text-mode.
Change-Id: Ic3d6932fbaf720d88daaac7e4b09c3c0b9f0b0e2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1178
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
The wrapper for Trinity. Support S3. Parme is a example board.
Change-Id: Ib4f653b7562694177683e1e1ffdb27ea176aeaab
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1156
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The constant value 0x100000000 is used in linker scripts to calculate
offsets from the end of 32-bit-addressed memory. There is nothing
wrong with it, but 32-bit versions of ld do the calculation wrong.
Change-Id: I4e27c6fd0c864b4d98f686588bf78c7aa48bcba8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1129
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
As Mathias Krause pointed out, using movw/outw on %al is clearly invalid.
Let's do another typo fix...
Change-Id: Ib95832a11097f599a236ab30c64c26ef429a1699
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1119
Tested-by: build bot (Jenkins)
Reviewed-by: Mathias Krause <minipli@googlemail.com>
|
|
Peter and Ron pointed out two typos. They have no side effects, but
it's still worth to fix them.
Change-Id: I9aecccdbc72beb2623fbe558a06e4f1b050f6e74
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1117
Tested-by: build bot (Jenkins)
|
|
Not doing a hard reset leaves the BOFL0 register cleared, which
prevents the BSP selection from working. To make sure we start
with known values, use the SPAD0 register for soft reset detection.
If there's a value other than 0, do a hard reset.
Change-Id: I390e3208084cfd32d73cce439ddf2bc9d4436a62
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1103
Tested-by: build bot (Jenkins)
|
|
Originally, ChromeBooks would get the offset of the MRC cache
from an entry in the u-boot device tree. Not everyone wants to
use u-boot on Sandybridge systems, however.
Since the new code (based on Kconfig) is now fully working, we
can drop the u-boot device tree remnants.
Change-Id: I4e012ea981f16dce9a4d155254facd29874b28ef
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1051
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The MRC region is described by Kconfig variables, no further math
or parsing is required at this point.
Change-Id: I290d8788b69ef007e9ea2317ce55aefa2d791883
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1046
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Remove all the repeated sections of code in cbtypes.h and place it
in a common location. Add include dir in vendor code's Makefile.
Change-Id: Ida92c2a7a88e9520b84b0dcbbf37cd5c9f63f798
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Reviewed-on: http://review.coreboot.org/912
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Requirements:
- must be in ramstage (locking flash while executing code from there
might not work)
- must be after cbmem is reinitialized (so the mrc cache copy of the
current run can be found)
Change-Id: I8028fb073349ce2b027ef5f8397dc1a1b8b31c02
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1002
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Separate Sandybridge from ChromeOS a bit
The Sandybridge code depends on chromeos features a whole lot.
As a first step, provide a code path to look up the MRC cache
without depending on u-boot.
- Move mrc cache handling to separate file
This enables us to handle the MRC cache from ramstage,
where we can write the flash safely (eg. to update the
cache).
Also teach it to lookup the current MRC cache from CBMEM,
as the original data block isn't available anymore.
After all the preparations, finally write to the SPI
as necessary. It's a simple round robin wear levelling
that erases the entire MRC cache region when it's full
and starts from the beginning.
Change-Id: I4751385574cf709b03d5c9d153b7481ffc90ce12
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1001
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Replace #elif (CONFIG_FOO==1) with #elif CONFIG_FOO
find src -type f -exec sed -i "s,\(#.*\)(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]1),\1\2,g" {} +
(manual tweak since it hit a false positive)
Replace #elif (CONFIG_FOO==0) with #elif !CONFIG_FOO
find src -type f -exec sed -i "s,\(#.*\)(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]0),\1\!\2,g" {} +
Change-Id: I8f4ebf609740dfc53e79d5f1e60f9446364bb07d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1006
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Replace #if CONFIG_FOO==1 with #if CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*1[[:space:]]*\$,#if \1," {} +
Replace #if (CONFIG_FOO==1) with #if CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*1)[[:space:]]*\$,#if \1," {} +
Replace #if CONFIG_FOO==0 with #if !CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*0[[:space:]]*\$,#if \!\1," {} +
Replace #if (CONFIG_FOO==0) with #if !CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*0)[[:space:]]*\$,#if \!\1," {} +
(and some manual changes to fix false positives)
Change-Id: Iac6ca7605a5f99885258cf1a9a2473a92de27c42
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1004
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
Change-Id: I9217a75ec1a0abb898c45752d990231ce98e5fb2
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/991
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: If183611b0b62d9321a5a12311c4cb3b344b04b36
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/986
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This fixes my build when specifying an absolute path to the binary.
Change-Id: I95fb3960be70f78146c6afeb9cc777dccdca6b5b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/987
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
It is important to have the system configuration reported as early as
possible to have a better idea what exact chipset the platform is
running with.
This change adds code to have an early coreboot module report the CPU
and PCH information. CPU info includes the 32 bit feature information
word, the symbolic processor brand string, and information about some
features support, as obtained through CPUID instructions.
The PCH information includes the symbolic device name and PCI device
version.
Change-Id: If6c21ad5ffb76d7d57d89f4f87d04bdd7192480a
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/975
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
- New table for GT1
- Updates to GT2 17W table
- New table for GT2 35W SKU
- New table for GT2 Other
This also includes a workaround to poll on a different register
when deasserting force wake. On some SKUs the kernel is hanging
when bringing up graphics unless this register is also polled.
Change-Id: I2badf62b464e901cfb0eaf4fc196f59111c71564
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/974
Tested-by: build bot (Jenkins)
|
|
- Add config options to set backlight registers
- Update powermeter weight tables for IvyBridge GT1 and
add a new table for GT2 SKU
- Fix a few registers used during GPU PM init sequence
Change-Id: I1500bc07e3ba1bc10c77e7856089e716489dc07a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/973
Tested-by: build bot (Jenkins)
|
|
This is done inside the SystemAgent binary on Ivybridge.
Change-Id: I8fb0f593a65a4803e160b284c21b9d5021e2e4a0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/970
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The ASPM setting for the Direct Media Interface should no longer be done on
Ivybridge/PantherPoint based systems.
Change-Id: Id30de1beb1b162564048e76712736ccf7049dc7c
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: http://review.coreboot.org/969
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This fixes a few cosmetics with the following three boards:
- Intel Emerald Lake 2
- Samsung ChromeBook
- Samsung ChromeBox
The following issues were fixed:
- rely on include path in ASL code instead of specifying relative
paths
- use updated ALIGN_CURRENT in acpi_tables.c
- use preprocessor defines instead of hard coded values where possible
Change-Id: Ia5941be3873aa84c30c13ff2f0428d1c52daa563
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/963
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
|
|
This code is still using libfdt which was denied for inclusion
in coreboot, so it won't compile as is.
Without MRC cache, waking from suspend won't work, and cold boots are
significantly slower (adds around 300-400ms per channel IIRC).
A rework of this code is currently in the works, but will take a little bit
more time (and should not hold back the mainboards being merged)
Change-Id: Ifb9e7d7b86c1f52378803a748810da0d51b58384
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/948
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
AMD supplies their video bios for the Family 14h processor line
with Vendor ID: 1002, Device ID: 9802. This rom should work for
Device IDs 9802-9809. This patch maps all those device IDs to
0x9802 so coreboot will be able to load the vbios. If a vbios
rom using the ACTUAL Device ID is loaded, this function will not
be called.
This file should contain of all Family 14h Graphics PCI IDs so
that they don't need to be overridden on a per mainboard basis.
Change-Id: If3d4a744b3c400dea9444a61f05382af2b2d0237
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/955
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
- When calling map_oprom_vendev() the vendor ID and device ID
are joined into a 32 bit value. They were reversed from the
order that I would have expected - Device ID as the high 16 bits
and the Vendor ID as the low 16. This patch reverses them so
so that the the dword comparison in map_oprom_vendev() matches
what's entered into Kconfig for vendor,device.
- Change files calling map_oprom_vendev()
Change-Id: I5b84db3cb1a359a7533409fde7d05fbc6ba3fcc4
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/938
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
