| Age | Commit message (Collapse) | Author |
|---|
|
Especially on ICH7 failing to do so results in i2c block read being
unusable. On ICH10 this problem doesn't manifest itself that much.
This moves disabling the watchdog reboot to the northbridge code like
i945 (even though it technically is southbridge stuff).
TESTED on Intel DG41WV: hacking on raminit is much nicer since no
need to do a hard power down for +4s are needed to clear the timeouts.
Change-Id: Icfd3789312704f61000a417f23a121d02d2e7fbe
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
gma.c of Nehalem was copied from Sandy/Ivy Bridge, so fix it there too.
Tested on lenovo/x230. Since both the bit that was masked wrongly and the
one that wasn't masked, but sould have been, are 0, the behaviour on
lenovo/x230 doesn't change.
Change-Id: I5f51c4929df83f948fcb7dc06e07ac3cc4ccf4f2
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/22596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
These were forgotten when updating the caller and resulted in build
failures for every but the NGI path.
Change-Id: I2490a3b4dca6c248eb37f43aa676ae619afdbfc7
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/22930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is mostly written from scratch and uses common spd ddr2 decode
functions.
This improves the following:
* This fixes incorrect CAS/Freq detection on DDR2;
* Fixes tRFC computation; tRFC == 78 is a valid timing which is
excluded and 0 ends up being used; (TESTED)
* Timings selection does not use loops;
* Removes ddr3 spd decode and is re-added in follow-up patches using
common ddr3 spd functions;
* Raminit would bail out if a dimm was unsupported, now in some cases it
just marks the dimm slot as empty;
* It dramatically reduces stack usage since it does not allocate 4
times 256 bytes to store full SPDs, amongs other unused things that
were stored in sysinfo;
* Reports when no dimms are present;
* Uses i2c block read to read SPD which is about 5 times faster than
bytewise read, with a fallback to smbus mode in case of failure,
which does seem to happen when the system is forcefully powered
off.
Change-Id: I760eeaa3bd4f2bc25a517ddb1b9533c971454071
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This fixes some bitwise logic errors that caused the coarse offset not
to be programmed.
This fixes a regression introduced by 6d7a8c
"nb/intel/x4x/raminit: Rework receive enable calibration"
where the coarse offset doesn't get programmed anymore.
TESTED on Foxconn g41s-k on a DIMM where the final DQS receive enable
delays are close but above and below the edge of a coarse delay setting.
Change-Id: I41869815f782a2ea1178bdea006e3a7587441323
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Corrects MBSC/MBFS programming when initializing DRAM on boards with both
3 and 4 DIMM slots.
Reformats comments to current coreboot standards.
Drops some romcc "optimizations" no longer necessary.
Boot tested on asus/p2b-ls, where it fixes a memory related hang after
SeaBIOS resets the board with nothing to boot from.
Change-Id: Ib8c21489338643e13f69bd58008d14733796d4d0
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/22687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ibfe6a6dc63454deacfd12de6dad2d6a792474f55
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/22270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I22241427d1405de2e2eb2b3cfb029f3ce2c8dace
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/22585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I9f96561120d0feb44c5edd9e7241bc3456b31e5f
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/22221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This partially reverts 2510e2aa "northbridge/intel/i3100: Unify UDELAY
selection" which moved all supported boards from UDELAY_TSC to
UDELAY_IO. Since UDELAY_IO is the default this changes nothing.
Change-Id: I42856e5929a7ba047987414a25cd0ae9712434a7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22173
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Simplifies our C interface function gma_gfxinit(), due to the following
changes:
* *libgfxinit* knows about the underlying PCI device now and can
probe MMIO addresses by itself.
* The framebuffer mapping is now completely handled inside the
library where we validate that we neither overflow
- the stolen memory,
- the GTT address space, the GTT itself nor
- the aperture window (i.e. resource2 of the PCI device)
that we use to access the framebuffer.
Other changes:
* Fixes and a quirk for DP training.
* Fix for DP-VGA adapters that report an analog display in EDID.
* Fixes for Skylake support with coreboot.
* DDI Buffer drive-strength configuration for Haswell, Broadwell and
Skylake.
* `gfx_test` can now be run from X windows (with glitches).
* Compatibility with GCC 7 and SPARK GPL 2017.
TEST=Booted lenovo/t420 and verified that everything works as usual.
Change-Id: I001ba973d864811503410579fd7ad55ab8612759
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/20606
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The current header `i915.h` is too invasive to be used everywhere where
we want to use *libgfxinit*.
Change-Id: Iba57256d536e301e598d98182448d2daa1bf9a89
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Port the ACPI opregion implementation that resides in
drivers/intel/gma to older platforms. It allows to include a vbt.bin and
allows GNU/Linux to load the opregion as ASLB is being set.
Windows' Intel will likely ignore it as it relies on legacy VBIOS
to be loaded at 0xc0000.
Change-Id: Ifc9fc52d84dcbb0da577e61467ece8a48752f44b
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/21775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This commit just moves the vboot sources into
the security directory and fixes kconfig/makefile paths.
Fix vboot2 headers
Change-Id: Icd87f95640186f7a625242a3937e1dd13347eb60
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
XMP profiles can have a restriction on max supported DIMMs per channel,
but many configurations work with more DIMMs.
This is relevant on mainboards with 2 DIMM slots per channel (usually 4
in total). Populating both slots with DIMMs that support XMP profiles only
with 1 DIMM per channel turns off said XMP profiles.
TEST=On a system with two DIMM slots per channel populate both slots on
one channel and ensure that DIMMs run with XMP profiles enabled.
Change-Id: I1f22d981afcef0ee73785823b0a943cf3d3564e3
Signed-off-by: Vagiz Trakhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21841
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
DRAM Controller is always 00.0. No need to check its PCI ID.
Change-Id: I9c5f3e5658905e464491579f8da01aa6a03bd3b7
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I1899dbe9498a0cc83b65b4bc1c6c0a555637fd05
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Port the ACPI opregion implementation that resides in
drivers/intel/gma to older platforms.
It allows to include a vbt.bin and allows GNU/Linux to load the
opregion as ASLS is being set.
Windows' Intel will likely ignore it as it relies on legacy VBIOS
to be loaded at 0xc0000.
Tested successfully on DG43GT (x4x) with vbt.bin,
with X200 (gm45) with vendor option rom and
D945GCLF (i945) with fake vbt.
Change-Id: I1896411155592b343e48cbd116e2f70fb0dbfafa
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/21766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The scramble seed intended for CH1 were written to the regs of CH0.
Write the scramble seed for CH1 at the correct offset.
TESTED on Lenovo T430, HP 2760P, Asrock B75PRO3-M.
Change-Id: I3778947e96b3298c38e6d5b74988e617e1ffea7b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Iru Cai <mytbk920423@gmail.com>
|
|
Try restoring previous memory training results from SPI flash
to improve raminit speed.
Change-Id: I6f4c2342e2eea6c1ecfb71da8564225b6230f51e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This code path was only triggered in one corner case: GFX UMA set to
48MiB. It created a hole below UMA to save MTRRs. But, this hole was
never accounted for when calculating cbmem_top(). Instead of trying
to fix it, remove it, it's not worth the trouble.
TEST=Booted lenovo/x200 with all available CMOS gfx_uma_size settings.
Change-Id: I3f4ceec4224d86113be9bfa3ce4759bed584640d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/21847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Remove no-op statements and code-rephrasing comments, apply some cosmetic
changes to improve readability.
Change-Id: I124a6bc338c2589fab66ca91bf53139b4413d10b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/21823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: Ic1713d1530071e29bd04b525f68d4a44d20ea2e2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21735
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Add debug messages for SPD probing.
Change-Id: I722102b7981781b88cdc4877f698294eb719ff32
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/21638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
New AGESA support files will be used for binaryPI
platforms as well. Furthermore, some of those should
move from split nb/ sb/ directories to soc/, so move
support files for the API under drivers/.
Change-Id: I549788091de91f61de8b9adc223d52ffb5732235
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21455
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Move all boards that have moved away from AGESA_LEGACY_WRAPPER
or BINARYPI_LEGACY_WRAPPER to use POSTCAR_STAGE.
We use POSTCAR_STAGE as a conditional in CAR teardown to tell
our MTRR setup is prepared such that invalidation without
writeback is a valid operation.
Change-Id: I3f4e2170054bdb84c72d2f7c956f8d51a6d7f0ca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21384
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I1d4b86c0e74cf4e1a7862889638125e5adcd4c3d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ide14bd164fe4a1846f86c6be326e2cd4f540bf97
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21662
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I077677c10508a89a79bcb580249c1310e319aaf1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21664
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This file mostly mimics Porting.h and should be removed.
For now, move it and use it consistently with incorrect form
as #include "cbtypes.h".
Change-Id: Ifaee2694f9f33a4da6e780b03d41bdfab9e2813e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
SPD decoding problems are no longer a good method for detecting if i2c
byte read failed, since the return value of i2c_block_read is checked.
Change-Id: I230aa22964c452cf28a9370c927b82c57e39cc62
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Needed for coreboot spi driver.
Change-Id: I01059c8cbdc6a002dfd75b6da3a629811b137702
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: If6cf47e4a87cf008d51f65fd1c1c79392c4b2786
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/21619
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4503f2c27774b68da7fa7294ddb6d00c81f167c7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This simplifies computing dram timings a lot.
This removes computation of rank size based on columns, rows,
banks,... and uses the information in SPD byte 31. The result of this
is that dimms with multiple asymmetric ranks are not supported
anymore. These however are very rare and most likely never tested on
this platform.
This also uses i2c block read instead of byte read to speed up the
raminit. The result is less time is being spend reading SPDs.
It still keeps smbus read byte as a backup if i2c block read were to
fail.
Change-Id: I97c93939d11807752797785dd88c70b43a236ee3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I270d17a2eff2c6664bf936425a6ed344be3feabe
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/21524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
According to clang, main has no prototype for bcom/winnetp680
so add it into corresponding raminit.h
Change-Id: I8a55267901986757a4fa88ee13460ffbed3eeadc
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/21356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There's no reason to mutate the struct device when determining
the ACPI name for a device. Adjust the function pointer
signature and the respective implementations to use const
struct device.
Change-Id: If5e1f4de36a53646616581b01f47c4e86822c42e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Use macro instead of numbers
Change-Id: Ife1aff0a5cf311881b3a11533b71a74c518a633f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/21472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Implement cbmem_top() required for cbmem support in romstage.
Boot tested on asus/p2b-ls. Boards to move to this setup in
followup patches.
Change-Id: I432f145a5343c1bb5f2b0de3b6b88f57124d1bd9
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20977
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I1a96b1c6181cd657d7aee82370ef86acd688cc94
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I8c783e966cf90c6def28d87f07903f50a11487d0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I84c70aa04ab556a3898d3525f7b9aab85812f61d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Even with the watchdog disabled, these bits influence other hardware
blocks (e.g. SECOND_TO_STS stops SMBus block transfers, possibly yet
before they started).
Change-Id: If9f93fcc96827bb192148a80b4476796c9358a7a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/21471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
With AMD_INIT_ENV and AMD_INIT_S3LATERESTORE moved
from romstage to ramstage, heapamanager in romstage
is no longer needed.
Change-Id: Iea8ad3ddb245c83dd290436ac9d4ecac9350b88c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Vendorcode expects some DRAM controller registers to
be writable, but they are actually locked after soft
resets if C6 states are enabled.
Without the workaround, raminit fails on soft resets.
Change-Id: I6b9e275e11b2907d026c13341334983a4d9c8889
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Iffa6cf495b4649f73a1095732509f195ac828248
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ie316df6e2babd8b3e9e79f45ea9719b52b0c2902
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This recovers FCH configuration on S3 resume path.
Appearst to work, but other defects of HAVE_ACPI_RESUME
must be fixed also before S3 support is re-enabled.
Change-Id: I8d07d2e9dc161b67d854fcc8ec1da1f36900f989
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Inspired by gm45 code, which sets this value the same way.
Some values for tRD on 800 and 1067MHz FSB were set wrong because the
CAS/Freq selection was wrong. CAS was often selected to low and when
fixing CAS this results in tRD being too high, due to an incorrect
lookup table which caused instability.
PASSED memtest86+ during 10h+ on 1067MHZ fsb with 667MHz ddr2, CAS 5
on GA-945GCM-S2L.
Change-Id: I8002daf25b7603131b78b01075f43fd23747dd94
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
We set the SPI lockdown in BS_POST_DEVICE (dev_finalize()) on many plat-
forms now. The SPI controller is initialized at start of BS_DEV_INIT
(dev_initialize()).
The SPI lockdown usually shouldn't be a problem but the SPI driver imple-
mentation lacks full support for the locked interface. Also, some options
exist to lock all flash regions read-only until the next reboot.
Change-Id: Ifda826ae2bb28adcce8dda8e2bb16dc38fe0fe9e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/21326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nicola Corna <nicola@corna.info>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Bill XIE <persmule@gmail.com>
|
|
Without this remapping code enabled, the system fails to boot properly
if the amount of ram inserted is larger than 4G minus the mmio
space (hardcoded to 1G here).
Change-Id: I02e7ceed0cd9db7eb7182481b6989f80cef31ee5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Fix dump_pci_device() broken by commit 65b72ab5 (Drop print_ implementation
from non-romcc boards) in 2015 (!) where only one in 16 bytes were being
dumped.
Also remove the #if made redundant by commit aef8542 (Compile debug.c
only if CONFIG_DEBUG_RAM_SETUP) as this whole file is only compiled in
that case.
Also clean up headers that were included twice.
Change-Id: I60e272b29417039feb15540e49d7300f86e5ed21
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21203
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Some of these will move to EARLY_CBMEM_INIT.
Change-Id: Ia969e30ad7097860180bd047eaf81859a42a747c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Keith Hui <buurin@gmail.com>
|
|
Change-Id: I18c62ad034249c5ad14e5d5e708b4f0d4bcbf400
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Never selected in our tree. The vendorcode source
for fam15 also includes fam10 support if required.
Change-Id: Ifff328ecdd8afa988f844b6fd631818b51bd5b5b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Vendorcode for f15 also has f10 support, so
AMD_AGESA_FAMILY_10 was never selected.
Change-Id: I9a026c36ace88f1110a52d7e24d3e6ab36508932
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This problem was introduced in:
12a4e98cea nb/intel/pineview/raminit: Refactor timings selection
Change-Id: Iace3dabb8546d7a721ef13526ba02522dc712fdd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: Ia55c82f2245335a5d02e4d6567f606596c8439c0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Avoid conflicting disable_cache_as_ram() declaration and tidy
up include for inlined function.
Change-Id: Iba77c711f5eb023566b7d8ba148583948661bc99
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
A small typo in the dll setting code prevented this combination from
booting.
TESTED on ga-g41m-es2l with 800MHz FSB CPU and 667MHz ddr2
Change-Id: Ib013471773c20336ba0902b7f328bfb6ef970747
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Moves receive enable calibration to a separate file to lighten
raminit.c a bit.
Receive enable calibration is quite similar to gm45 so it reuses some
of its function names.
The functional changes are:
* the minimum coarse is now reset for each channel;
* on the second fine search for DQS high, TAP overflow is handled by
increasing medium;
* start coarse at CAS + 1 instead of CAS - 1. Other Intel northbridges
do the same and the results are more in line with register dumps
from vendor bios.
These might improve stability.
TESTED on ga-g41m-es2l
Change-Id: I0c970455e609d3ce96a262cbf110336a2079da4d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
... is enabled. Otherwise we are compiling an effectively
empty file.
Change-Id: I4e3d982066d1fa66a3da5f37e278ec7fd5bb1ea8
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
Due to low-memory corruptions S3 support has now been
(at least temporarily) removed from AGESA platfroms.
Should we bring it back one day, CAR teardown on S3 path
will happen with an empty stack so ugly backup/recovery
of the stack will no longer be used.
If S3 feature is brought back, resume path code for FCH
will also see partial rewrite and agesawrapper.c file
will not be part of that.
Change-Id: Ib38c04d0e74f600e0b719940d5e2530f4c726cfd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
A decision has been made that boards with LATE_CBMEM_INIT
will be dropped from coreboot master starting with next
release scheduled for October 2017.
As existing implementation of CAR teardown in AGESA can only
do either EARLY_CBMEM_INIT or ACPI S3 support, choose the former.
ACPI S3 support may be brought back at a later date for
these platforms but that requires fair amount of work fixing
the MTRR issues causing low-memory corruptions.
Change-Id: I5d21cf6cbe02ded67566d37651c2062b436739a3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The S3 resume path is broken on current Linux (4.11.3) and maybe
on older kernel, too.
Don't run the native graphics init when on S3 resume to fix it.
Tested on Lenovo T430.
Change-Id: Ifad145c86c2e8f019c507f97c889b70b7aa49882
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This allows the use of the native VGA init on boards featuring DVI-I
ports. Digital output is not supported.
Change-Id: I11a4dd68746e06c7e27ecf3e765bdd0d8cf40515
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Migrate opregion code from northbridge/intel/common to
drivers/intel/gma in preparation for consolidation with
soc/intel/common opregion code. Rename init_igd_opregion()
for clarity and disambiguation with other implementations.
Change-Id: I2d0bae98f04dbe7e896ca34e15f24d29b6aa2ed6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Add a new Kconfig option to ignore memory fuses that limit the
maximum DRAM frequency to be used. The option is disabled by
default and should only enabled by experienced users as it
might decrease system stability or prevent a successful RAM
training.
Remove conflicting devicetree settings.
Change-Id: I35dd78a02bcaafce8ba522d253c795d7835bacae
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nicola Corna <nicola@corna.info>
|
|
Change-Id: I730a8a150134cc1ef8fb3872728bb0586ac7b210
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19732
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I885b6bd9f5be6b4e3696a530016123a3e81c4b10
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
All Intel southbridges implement the same SMBus functions.
This patch replaces all these similar and mostly identical
implementations with a common file.
This also makes i2c block read available to all those southbridges.
If the northbridge has to read a lot of SPD bytes sequentially, using
this function can reduce the time being spent to read SPD five-fold.
Change-Id: I93bb186e04e8c32dff04fc1abe4b5ecbc4c9c962
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
We define BINARYPI_LEGACY_WRAPPER a method of calling AGESA
via functions in agesawrapper.c file. The approach implemented
there makes it very inconvenient to do board-specific
customisation or present common platform-specific features.
Seems like it also causes assertion errors on AGESA side.
The flag is applied here to all boards and then individually
removed one at a time, as things get tested.
New method is not to call AGESA internal functions directly,
but via the dispatcher. AGESA call parameters are routed to
hooks in both platform and board -directories, to allow for
easy capture or modification as needed.
For each AGESA dispatcher call made, eventlog entries are
replayed to the console log. Also relocations of AGESA heap
that took place are recorded.
New method is expected to be compatible with binaryPI.
Change-Id: I2900249e60f21a13dc231f4a8a04835e090109d5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I622d155fce3fa56cd5e24282e22de060fed560c3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This FCH_OEM_CALLOUT bypasses API and uses structures
that are private to AGESA. Attempt to clean it up by
first clarifying when it is used.
Change-Id: I63aa0f586f73e97d615b8596d73728edbaeb0a2d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I0c0058be002e409bd16d2d75fd404df94407df4e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Also moves postcar stack to CBMEM.
Change-Id: I0263af9561e0367bbbde4d5c3190039f4c3047a0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19347
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
Change-Id: Id199322db077fc5f112dfa45f8e9f72b9142a8fb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20770
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Boards without AGESA_LEGACY_WRAPPER gain EARLY_CBMEM_INIT.
This does not apply to family12 and family14 just yet, as
they do invalidate without write-back on CAR teardown.
Change-Id: I008356efa2bc3df0ed1f0720e225ecc7e9995127
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ide49e46c0b6aa5e1bf09354435a847a46bc797c9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In AGESA specification AmdInitEnv() is to be called once
host memory allocator has started. In coreboot context this
could mean either availability of CBMEM or malloc heap.
As for AmdS3LateRestore(), there is no requirement to have
it run as part of the romstage either.
Change-Id: Icc8d97b82df89e2480e601d5c2e094de0365b0a5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I54c8553bc057798e595b28f6cbc07f7125ae074f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
We define AGESA_LEGACY_WRAPPER a method of calling AGESA
via functions in agesawrapper.c file. The approach implemented
there makes it very inconvenient to do board-specific
customisation or present common platform-specific features.
Seems like it also causes assertion errors on AGESA side.
The flag is applied here to all boards and then individually
removed one at a time, as things get tested.
New method is not to call AGESA internal functions directly,
but via the dispatcher. AGESA call parameters are routed to
hooks in both platform and board -directories, to allow for
easy capture or modification as needed.
For each AGESA dispatcher call made, eventlog entries are
replayed to the console log. Also relocations of AGESA heap
that took place are recorded.
New method is expected to be compatible with binaryPI.
Change-Id: Iac3d7f8b0354e9f02c2625576f36fe06b05eb4ce
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I916d808d1b2ecc4b70b5dfebff62c4a18119f157
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Also avoid infinite loop.
Change-Id: I7571f9efdc2bf0335788136b8c56e9290581d748
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I2d6ab1026f1105f1fea97682442a169409248c39
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I93b939478615f22f2c078b1efb7999ad4f3a4c28
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20747
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Sync map_oprom_vendev() and autoport with the list of PCI ids in the
`gma.c` driver, remove one obsolete Kconfig default override.
Change-Id: I12f24f415b695c516fbb947114e09c873af2e439
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/20814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
All affected boards did the same USE_NATIVE_RAMINIT distinction or
actually selected USE_NATIVE_RAMINIT. Also update autoport.
Change-Id: I924c43cec1e36e84db40e4b8e1dd0e05cad2b978
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/20813
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Never reached and actual code was already wiped out.
Change-Id: Ic17cbc56e83d23e228e23578357843ac9cd77eda
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20623
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The newline lint check just went in, and immediately broke the build
due to a commit that went in earlier today.
This fixes the build.
Change-Id: Ic4ba8ce0c8085861bc6c654afdee3fea9f4621fc
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
There are 4 routines used in RAM init that most if not all
i440bx mainboards call in the same order. Implements a single
RAM init routine for them to allow for future consolidation.
Boards to be changed to use this one routine in a future change.
Change-Id: Ib553b07b117de12b7982586bce0f9355f55013a0
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This move makes the NB macro more widely available,
in preparation for implementing get_top_of_ram().
Change-Id: Icd8e82cfdfdccb662b2139d0e5d1d5af72cbae7f
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This does the following:
* Clarify that settings are set to the same value for each rank;
* Allows to program coarse
* Fix some style issues like white spaces between arithmetic
operators.
Change-Id: I3a9e28cfec915a0bb15789c23bea259f621b5096
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This does not use loops to compute timings but uses DIV_ROUND_UP.
Another thing affected by this patch are minimum timings. Presumably
those only need to be guarded against on DDR3. With this change
timings are set up like vendor (with tWTR below previous minimum)
TESTED on Intel D510MO
Change-Id: Ia374f26e5bbb8b90d90c24ae6c20412ba53bd7b6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ic9226098dafa2465aa5fccc72c442de2b94e44c7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Id20a49385aeb336461acd0bd186a4ab7f3fb95b8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Essentially squashes following commits from AGESA side.
45ff9cb AGESA: Reduce typecasting in heapmanager calls
bceccec AGESA: Handle HEAP_CALLOUT_RUNTIME allocation more cleanly
4240277 AGESA: Adjust heap location for S3 resume path
424c639 AGESA: Refactor S3 support functions
50e6daf AGESA: Log heap initialisation
da74041 AGESA: Move heap allocator declarations
c74b53f AGESA: Reduce SPI use by 24kB for S3 support
b1fcbf3 AGESA: Separate HeapManager declarations from BiosCallOuts
f728408 AGESA: Split S3 backup in CBMEM
82fbda7 AGESA: Use same HeapManager for all BiosCallOuts
Change-Id: I537bd05a3e06ff6896f1ac8be93eed5321ca472b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Also unify __attribute__ ((..)) to __attribute__((..)) and
handle ((__packed__)) like ((packed))
Change-Id: Ie60a51c3fa92b5009724a5b7c2932e361bf3490c
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/15921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
AMD_S3_PARAMS is no longer defined with all binaryPI.
Guard these as a build fix to share the header nevertheless.
Change-Id: I725ed43991dc1c3e30d236bde4282176819f4cf4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
