Age | Commit message (Collapse) | Author |
|
The intel-framework code has an updated pei_data structure.
Use the new structure and revision. Also, remove the scrambler
seed saving in CMOS since that appears to be handled in the saved
data from the reference code.
Change-Id: Ie09a0a00646ab040e8ceff922048981d055d5cd2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2630
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change the hard coded values in udelay.c to use the #defines
for MSRs and BCLK.
Change-Id: I2bbeb0b478d2e3ca155e8f82006df86c29a4f018
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2629
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Boot haswell ULT and see LPT reported properly.
Change-Id: I48344a8dde6adbbf331c91231342de45b1b6c32a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2697
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This is the steps outlined in the BWG.
It seems this is a lot simpler now (so far) which is good.
To test, boot to chromeos with 3.7 kernel + i915.preliminary_hw_support=1 and
see that the i915 driver complains a lot less than before and that a
splashscreen is displayed.
Change-Id: I722c90ecd351860949cedab24533f6c10e5b90e5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2696
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add a bootblock.c file for the northbridge and setup the
PCIEXBAR as the first thing using IO PCI config acceses.
After that all PCI config accesses can use MMIO.
Change-Id: I51d229c626c45705dda1757c2f14265cbc0e6183
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2617
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The Haswell parts use a PCH code named Lynx Point (Series 8). Therefore,
the southbridge support is included as well. The basis for this code is
the Sandybridge code. Management Engine, IRQ routing, and ACPI still requires
more attention, but this is a good starting point.
This code partially gets up through the romstage just before training
memory on a Haswell reference board.
Change-Id: If572d6c21ca051b486b82a924ca0ffe05c4d0ad4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2616
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add PEI updates and ACPI updates for supporting EHCI to XHCI
USB port support.
Change-Id: I9ace68a1b3950771aefb96c1319b8899291edd9a
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2519
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
This is required to enable EARLY_CBMEM_INIT.
Change-Id: I6d8caf382aa48eded81c1e94bbbcd3975ea88a1a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2550
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
It's been on for all boards per default since several years now
and the old code path probably doesn't even work anymore. Let's
just have one consistent way of doing things.
Change-Id: I58da7fe9b89a648d9a7165d37e0e35c88c06ac7e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2547
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The name lapic_cluster is a bit misleading, since the construct is not local
APIC specific by concept. As implementations and hardware change, be more
generic about our naming. This will allow us to support non-x86 systems without
adding new keywords.
Change-Id: Icd7f5fcf6f54d242eabb5e14ee151eec8d6cceb1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2377
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The name pci_domain was a bit misleading, since the construct is only
PCI specific in a particular (northbridge/cpu) implementation, but not
by concept. As implementations and hardware change, be more generic
about our naming. This will allow us to support non-PCI systems without
adding new keywords.
Change-Id: Ide885a1d5e15d37560c79b936a39252150560e85
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2376
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Since there are and will be other files in nb/sb folders, we change
the general spi.h to a file name which is not easy to be duplicated.
Change-Id: I6548a81206caa608369be044747bde31e2b08d1a
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2309
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
And move the corresponding #define to speedstep.h
Change-Id: I8c884b8ab9ba54e01cfed7647a59deafeac94f2d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2339
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Summary:
Isolate CBFS underlying I/O to board/arch-specific implementations as
"media stream", to allow loading and booting romstage on non-x86.
CBFS functions now all take a new "media source" parameter; use
CBFS_DEFAULT_MEDIA if you simply want to load from main firmware.
API Changes:
cbfs_find => cbfs_get_file.
cbfs_find_file => cbfs_get_file_content.
cbfs_get_file => cbfs_get_file_content with correct type.
CBFS used to work only on memory-mapped ROM (all x86). For platforms like ARM,
the ROM may come from USB, UART, or SPI -- any serial devices and not available
for memory mapping.
To support these devices (and allowing CBFS to read from multiple source
at the same time), CBFS operations are now virtual-ized into "cbfs_media". To
simplify porting existing code, every media source must support both "reading
into pre-allocated memory (read)" and "read and return an allocated buffer
(map)". For devices without native memory-mapped ROM, "cbfs_simple_buffer*"
provides simple memory mapping simulation.
Every CBFS function now takes a cbfs_media* as parameter. CBFS_DEFAULT_MEDIA
is defined for CBFS functions to automatically initialize a per-board default
media (CBFS will internally calls init_default_cbfs_media). Also revised CBFS
function names relying on memory mapped backend (ex, "cbfs_find" => actually
loads files). Now we only have two getters:
struct cbfs_file *entry = cbfs_get_file(media, name);
void *data = cbfs_get_file_content(CBFS_DEFAULT_MEDIA, name, type);
Test results:
- Verified to work on x86/qemu.
- Compiles on ARM, and follow up commit will provide working SPI driver.
Change-Id: Iac911ded25a6f2feffbf3101a81364625bb07746
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2182
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I6b96b0e387dc3e6985eb1476fea612772a2288bc
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2145
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
As we move to supporting other systems we need to get rid of assembly
where we can. The log2 function in src/lib is identical to the assembly
one (tested for all 32-bit signed integers :-) and takes about 10 ns
to run as opposed to 5ns for the non-portable assembly version. While speed
is good, I think we can spare the 15 ns or so we add to boot time
by using the C version only.
Change-Id: Icafa565eae282c85fa5fc01b3bd1f110cd9aaa91
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1928
Tested-by: build bot (Jenkins)
|
|
This broke because those components were not yet
committed when the patch to drop the driver class
was made.
Change-Id: I29948223503a6c4b196eafa169c064cd26da1be1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1934
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
- Optionally override FSB clock detection in generic
LAPIC code with constant value.
- Override on AMD Model fxx, 10xxx, agesa CPUs with 200MHz
- compile LAPIC code for romstage, too
- Remove #include ".../apic_timer.c" in AMD based mainboards
- Remove custom udelay implementation from intel northbridges' romstages
Future work:
- remove the compile time special case
(requires some cpuid based switching)
- drop northbridge udelay implementations (i945, i5000) if
not required anymore (eg. can SMM use the LAPIC timer?)
Change-Id: I25bacaa2163f5e96ab7f3eaf1994ab6899eff054
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1618
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The use of ramstage.a required the build system to handle some
object files in a special way, which were put in the drivers
class.
These object files didn't provide any symbols that were used
directly (but only via linker magic), and so the linker never
considered them for inclusion.
With ramstage.a gone, we can drop this special class, too.
Change-Id: I6f1369e08d7d12266b506a5597c3a139c5c41a55
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The code supports DDR3 boards only. RAM init for DDR2 is sufficiently
different that it requires separate code, and we have no boards to
test that.
Change-Id: I9076546faf8a2033c89eb95f5eec524439ab9fe1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1689
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Makes it more similar to what realmode looks like.
Change-Id: I4407431f2d979c43dd186114d67ed11845907afe
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1892
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I716564c4ea3b8e298cdeb82dc68e68474ed595cc
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1879
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
If the PEI System Agent doesn't run PCIe initialization, the PEG
clock gating will not be setup. Add the PEG clock gating when
pei_data->pcie_init is 0.
Change-Id: I7e31bcebd11feb4807aa29b528adf09fb013c3ce
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1827
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The IvyBridge reference code does some slow and
extensive PCIe init that we do not need on Link.
Hence, add a flag to disable/enable running that
init code from coreboot.
NMode was used during bringup. We'll switch
the setting back to auto, to let MRC decide the right thing.
Change-Id: Ia989bb9ea079aadfeb41dc3029b7c2c623e84760
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1826
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This will enable DDR3 1.35V support for memory training in
the reference code. It requires the board to be setup for
1.35V with whatever board-specific GPIOs are available.
Change-Id: I14e4686c20f9610f90678e6e3bece8ba80d8621a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1825
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
I added a comment to the pei_data.h to remind users about
how the OC pins are mapped.
Change-Id: I4d74eb69fc78816a69e61260c2c9b2b3e58cafec
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1824
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Let memory initialization code use the coreboot romstage console. This
simplifies the code and makes sure that all output is available in
/sys/firmware/log.
The pei_data structure is modified to allow passing the console output
function pointer. Romstage console_tx_byte() is used for this purpose.
Change-Id: I722cfcb9ff0cf527c12cb6cac09d77ef17b588e0
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1823
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I9e57c5792409830895a1147799acab95d910a336
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1757
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The MRC cache code, as implemented, in some cases uses configuration
settings for MRC cache region, and in some cases - the values read
from FMAP. These do not necessarily match, the code should use FMAP
across the board.
This change also refactors mrccache.c to limit number of iterations
through the cache area and number of fmap area searches.
Change-Id: Idb9cb70ead4baa3601aa244afc326d5be0d06446
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1788
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On Sandybridge and Ivybridge systems the firmware image has to
store a lot more than just coreboot, including:
- a firmware descriptor
- Intel Management Engine firmware
- MRC cache information
This option allows to limit the size of the CBFS portion in
the firmware image.
Change-Id: Ib87fd16fff2a6811cf898d611c966b90c939c50f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1770
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
These can be stored in the code segment, since it's never changed.
Change-Id: I8b3827838e08e6cc30678aad36c39249fbca0c38
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1749
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Until now, the MRC cache position and size was hard coded in Kconfig.
However, on ChromeOS devices, it should be determined by reading the
FMAP.
This patch provides a minimalistic FMAP parser (libflashmap was too
complex and OS centered) to allow reading the in-ROM flash map and
look for sections.
This will also be needed on some partner devices where coreboot will
have to find the VPD in order to set up the device's mac address
correctly.
The MRC cache implementation demonstrates how to use the FMAP parser.
Change-Id: I34964b72587443a6ca4f27407d778af8728565f8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1701
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This is purely cosmetic. All error messages in the Sandybridge raminit
code printed a newline at the end.
Change-Id: I880d291928291d487039850a2a3d53a1101124ba
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1699
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This will allow the lower bank to be cleared without impacting the
ability to suspend/resume.
Change-Id: Iaec3c9e7e40c334053c814eaddd1f614df245a73
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1696
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Unfortunately the reference tool chain was updated
without ever even testing it on an abuild run. This
broke a number of ports.
This change gets coreboot at least compiling again
for all supported systems.
Change-Id: I92c7cbc834de6d792fdab86b75df339e2874c52e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1670
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Without this, the output of "Setting up ACPI…" continues right
after the output of stepping.
Change-Id: I2ad7cc3e55884ff509600b01274258b8e8250981
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1632
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
I don't know if the size main memory supposed to be in PCI(0,0) reg 0x9c
but it is not written there. The size of memory is written in
src/northbridge/intel/sch/raminit.c to SCH port(2, 8, 4) (look for
"Setting up TOM").
Change-Id: Iea04a5185bda56f61d1c382533d5a0dac429ebbd
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1629
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
The GGC register which contains the size of memory that is used for GPU
is in PCI device 2,0 and not 0,0. It is set to to 4MiB in
src/mainboard/iwave/iWRainbowG6/romstage.c.
Change-Id: Ie9f1cc60544ecd9cad770f34c83c33564a6129d4
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1628
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Without this, the hightables are placed just before the end of memory.
However we might have the GPU memory located at the exact same spot,
that is in the last 4 MiB. So without this patch, this area won't remain
marked as "CONFIGURATION TABLES" within coreboot's memory table but
becomes "RESERVED" because it is part of the PCI(2,0) device.
Change-Id: Ibd111c167c2f6ac03b0ba68581a74ecbd2c9c160
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1627
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Also deletes files not included in build:
src/southbridge/amd/cimx/sb700/chip_name.c
src/southbridge/amd/cimx/sb800/chip_name.c
src/southbridge/amd/cimx/sb900/chip_name.c
Change-Id: I2068e3859157b758ccea0ca91fa47d09a8639361
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1473
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
... but no-one told intel/sch.
Change-Id: I68eaae6910bd6fc579c35b5bc038b9597cd1b3e7
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1537
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The name is derived directly from the device path.
Change-Id: If2053d14f0e38a5ee0159b47a66d45ff3dff649a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1471
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
This was broken, fixing according to related patch for i945
Change-Id: I925cd205ee5beb918181740a7b981a4209688ac6
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1412
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The includes removed here were previously required for
struct lb_memory and lb_add_memory_range().
Change-Id: Ie6c0d4ef55c2225aa709cf3fbad30ff1080e3610
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1391
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
The names were set at various times during development, but
the way the code works, you might end up with the wrong name
being displayed in the logs. Instead of doing magic, just
display both names for each component
Change-Id: I1f8ce44d156442f5f7d717e1a2b47ed1218d4527
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1413
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Use of uma_resource() in northbridge code created a memory
resource marked as reserved. Such resources are removed
from system memory in write_coreboot_table().
Change-Id: I14bfd560140d8d30ec156562f23072bfae747bde
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1238
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
With SandyBridge northbridge code, uma_memory_size was reset to
zero before variable MTRRs were set. This means MTRR setup routine
did not previously create a un-cacheable hole for uma.
Keep the behaviour that way, mmio_resource() has a prerequisuite that
the new region does not overlap with any cacheable ram_resource().
The result is not optimal setup in the number of used MTRRs, but
continue with this approach until MTRR algorithm is improved.
Change-Id: I63c8df19ad6b6350d46a3eca3055abf684b8b114
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1373
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Reserved memory resources will get removed from memory table at
the end of write_coreboot_table(),
Change-Id: I02711b4be4f25054bd3361295d8d4dc996b2eb3e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1372
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
MRC messes with USB devices, so we have to reinitialize
USB debug after MRC has finished.
Change-Id: I45c0a687cebd69d0a31235bb870f8c455f42d4f2
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1377
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Commit 2d42b340034ff005693482ef9ca34ce3e0f08371 changed the
variable MTRR setup and removed compensation of uma_memory_size in
the cacheable memory resources.
Since the cacheable region size was no longer divisible by a large
power of 2, like 256 MB, this caused excessive use of MTRRs.
As first symptoms, slow boot with grub and poor user response.
As a solution, register the actual top of low ram with ram_resource(),
and do not subtract the UMA/TSEG regions from it.
TSEG may require further work as the original did not appear exactly
right to begin with. To have UMA as un-cacheable, use uma_resource().
Change-Id: I4ca99b5c2ca4e474296590b3d0c6ef5d09550d80
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1239
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Tested-by: build bot (Jenkins)
|
|
No need for the test, tomk is at most 1GB on these chipsets.
Even if there was no room, adjusting the memory resource would not
not divert accesses in the hardware from DRAM to PCI.
Change-Id: I2213b8d9d2e6ab8da8fd3e8081cc62bb05b6b316
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1369
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
No need for the test, tomk is top of low memory and always below 4GB.
Change-Id: Ifc8f29268b761aa9b07b578673236a673f0c70b5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1368
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Our driver infrastructure became more flexible recently.
Make use of it.
These are the low hanging fruits (files with 5 device
variants or more), but there are still lots of files
with less potential for deduplication.
Change-Id: If6b7be5046581f81485a511b150f99b029b95c3b
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1358
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Otherwise there is a flurry of TDP changes with suspend/resume
as the kernel powers devices off on suspend and brings them
back online in resume.
This also adds a mutex around the TDP operations since it is
split across two methods and can't just rely on being Serialized.
Change-Id: I7757d3ddad34ac985a9c8ce2fc202e2b2dcb2527
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1348
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The required power MSRs are mirrored in MCHBAR so
it is possible to configure TDP at runtime via ASL.
This adds the required fields and a set of methods to
configure "TDP down" and "TDP nominal". It explicitly
does not support "TDP up" at the moment.
PSSS: method is added to assist in searching the _PSS
table for the appropriate entry that corresponds to the
desired max non-turbo ratio.
STND: Set TDP Down from Nominal. This will limit CPU to
the TDP down configuration by sequencing the required
changes in the right order.
STDN: Set TDP Nominal from Down. This will set the CPU
back to nominal configuration by sequencing the required
changes in the correct (reverse) order.
This does not introduce any functional changes and must
be paired with additional changes to be useful.
The current configured TDP can be checked to see that
the transition to/from a desired level is successful.
> mmio_read8 0xfed15f50
0x00 # TDP-Nominal
> mmio_read8 0xfed15f50
0x01 # TDP-Down
Change-Id: I31a2f30cc9d134cc5eee980ae9288ae45e71c6e6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1344
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This maintains a 32bit monotonically increasing boot counter
that is stored in CMOS and logged on every non-S3 boot when
the event log is initialized.
In CMOS the count is prefixed with a 16bit signature and
appended with a 16bit checksum.
This counter is incremented in sandybridge early_init which is
called by romstage. It is incremented early in order notice
when reboots happen after memory init.
The counter is then logged when ELOG is initialized and will
store the boot count as part of a 'System boot; event.
Reboot a few times and look for 'System boot' events in the
event log and check that they are increasing. Also verify
that the counter does NOT increase when resuming from S3.
171 | 2012-06-23 16:02:55 | System boot | 285
176 | 2012-06-23 16:26:00 | System boot | 286
182 | 2012-06-23 16:27:04 | System boot | 287
189 | 2012-06-23 16:31:10 | System boot | 288
Change-Id: I23faeafcf155edfd10aa6882598b3883575f8a33
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1315
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
MRC returns specific error codes; print the according error
message if we know what it means.
Change-Id: Iaaf1512b9d577d4291fccfb94d879043ab5b11b5
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1289
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The count was only incrementing for a wake from S5 and
it was not incrementing in the normal reboot case.
Change-Id: I73bc6db6bd02e6c4677f7e44a5c098c6dcb51747
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1328
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
MCHBAR 0x5f10[7:0] should be set to 0x30 for ivybridge
and 0x20 for sandybridge. Move this code to ramstage
and set it per-chipset.
Power Aware Interrupt Routing is supported in ivybridge,
enable it and set fixed priority.
Boot on ivybridge device and read MCHBAR 0x5f10:
mmio_read8 0xfed15f10
0x30
And verify PAIR is enabled (bit4=1):
mmio_read8 0xfed15418
0x24
Change-Id: If017d5ce2bd5ab5092c86f657434f2b645ee6613
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1303
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Ivybridge B0+ CPUs are capable of supporting multiple TDP levels.
This complicates the default case because now the registers that
were reporting max non-turbo ratio are reporting that value for
the highest possible TDP level.
For now this change just forces everything to use the Nominal TDP
values instead of the higher (or lower) levels.
- When building P-state tables, determine the P[1] (max non turbo)
ratio based on the Nominal ratio if available.
- Set the turbo activation ratio to the Nominal max ratio.
- Mirror the power level settings in new MCHBAR register after
they are written, which happens after BIOS_RESET_CPL is set.
- Set the current ratio to Nominal ratio at boot.
1) Verify that P-state table is generated properly with
P[0]=1801MHz (ratio 0x1C) and P[1]=1800MHz (ratio 0x12)
PSS: 1801MHz power 17000 control 0x1c00 status 0x1c00
PSS: 1800MHz power 17000 control 0x1200 status 0x1200
2) Verify power limits in MCHBAR match PKG_POWER_LIMIT:
> rdmsr 0 0x610
0x800080aa00dc8088
> mmio_read32 0xfed159a4
0x000080aa
> mmio_read32 0xfed159a0
0x00dc8088
3) Verify turbo activation ratio is set to nominal ratio:
> rdmsr 0 0x64c
0x0000000000000012
4) Check that proper ratio was set at boot on one core only:
> grep 'frequency set to' /sys/firmware/log
model_x06ax: frequency set to 1800
model_x06ax: frequency set to 1800
model_x06ax: frequency set to 1800
model_x06ax: frequency set to 1800
Change-Id: I592e60a7740f31b140986a8269dca91b4adbb270
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1304
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
... and don't require it to specify a cache type.
This function is only used on romcc boards, and should go away
(because all boards should be switched to CAR)
Change-Id: Ic32ca3be1afffc773c72c140e88b338d48a0c8ca
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1288
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On systems with socketed CPUs we want to be able to
drop in a Sandy Bridge or Ivy Bridge CPU without recompiling the
firmware. Hence, detect the north bridge dynamically. In order
for this to work, we need Ivy Bridge MRC and coreboot configured
for Ivy Bridge.
Change-Id: I635bef2c61d47d36a3fdd87f8ecb6e69097ba969
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1281
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The function is empty (a left-over from i945) and should be removed.
Change-Id: I91e573b5e37cb9133ea1037aef7e6daf3c292864
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1290
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This lets the SPI driver and the LPC driver know about HM70 and NM70.
Change-Id: Id2f1e0e5586a2f7200b2d24785df3f2be890da98
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1300
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Right now, if we have an unknown PCH, coreboot will print something like
this:
PCH type: Unknown rev id 4
Instead, it should also print the PCI ID of the device, so we can add it
to the list of known PCHes.
Change-Id: Ib0b96e287c36d2895d1287b1734ca13d75e7985a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1287
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This is as per Intel's suggestion on how to display their name strings.
Change-Id: Ie82341305e58baa8041e50a61a11b395fa7d9582
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1298
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
When no valid MRC cache area is found, the mrc_cache data structure
was used without prior initialization. This sometimes caused a long
delay when booting because compute_ip_checksum would checksum up to
4GB of memory.
Change-Id: I6a0ca1aa618838bbc3d042be425700fc34b427f2
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1277
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I153579561f7eed6d4befd74ff39e1a5e778d0e46
Signed-off-by: Walter Murphy <wmurphy@google.com>
Reviewed-on: http://review.coreboot.org/1269
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
- The unneeded poll on non-MT force-wake bit was timing out
and causing the gma_pm_init_pre_vbios() function to exit
early so it was not preparing PM registers properly.
I changed the gtt_poll() calls to not return on timeout
unless it can't proceed so we don't see half-initialized
registers.
- RC6+ (Deep Render Standby) is not working reliably so we
can just enable RC6 in the BIOS and let the kernel decide
if it wants to enable RC6+ later.
This Kernel message is new in kernel 3.4:
[drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
Change-Id: I69d005ba56be8c7684a4ea1133a1d761f7c07acc
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1268
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
It's shut down, but UMA memory is not reclaimed. A later extension
could optionally do the magic register dance that allows initialization
of IGD as secondary graphics device.
Change-Id: I2a92bb71755005b886a8e1825325c678a9991bf2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1252
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Work around 32-bit overflow with 64-bit multiplication. Calculate
correct CPU frequency.
Change-Id: I86d78f2d70b9f9c62fd4e1e0d765e92e4de83f67
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1254
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: If131ac9df89080faccd8ed952d6fc019483b5b2e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1237
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Use of the uma_memory_base and _size variables is very scattered.
Implementation of setup_uma_memory() will appear in each northbridge.
It should be possible to do this setup entirely in northbridge
code and get rid of the globals in a follow-up.
Change-Id: I07ccd98c55a6bcaa8294ad9704b88d7afb341456
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1204
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The current code didn't reserve static resource the right way.
Also reduce TOLM to 0xd0000000, because those boards have so many PCI
devices that 0xe0000000 isn't sufficient.
Change-Id: Ia75a81905eea1a096aed464b63ac154e044bc99c
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1220
Tested-by: build bot (Jenkins)
|
|
Don't stop if RAM init fails at first try. It's better to restart
and try again instead of failing on the first try if the second
try would have worked.
Change-Id: Ib5660265d5b10a01588f2e4022dac2ee34f2c6d0
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1191
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I48be647e3f38038830200bcc64429cbf86990ad7
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1174
Tested-by: build bot (Jenkins)
|
|
This is mostly necessary for reboot, but it doesn't hurt the boot process.
On reboot explicitely reset the integrated graphics, otherwise the VGABIOS
might not be able to reinitialize it properly, and you either have a still
of the last pre-reboot image, garbage or an empty screen, but no text-mode.
Change-Id: Ic3d6932fbaf720d88daaac7e4b09c3c0b9f0b0e2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1178
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
As Mathias Krause pointed out, using movw/outw on %al is clearly invalid.
Let's do another typo fix...
Change-Id: Ib95832a11097f599a236ab30c64c26ef429a1699
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1119
Tested-by: build bot (Jenkins)
Reviewed-by: Mathias Krause <minipli@googlemail.com>
|
|
Peter and Ron pointed out two typos. They have no side effects, but
it's still worth to fix them.
Change-Id: I9aecccdbc72beb2623fbe558a06e4f1b050f6e74
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1117
Tested-by: build bot (Jenkins)
|
|
Not doing a hard reset leaves the BOFL0 register cleared, which
prevents the BSP selection from working. To make sure we start
with known values, use the SPAD0 register for soft reset detection.
If there's a value other than 0, do a hard reset.
Change-Id: I390e3208084cfd32d73cce439ddf2bc9d4436a62
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1103
Tested-by: build bot (Jenkins)
|
|
Originally, ChromeBooks would get the offset of the MRC cache
from an entry in the u-boot device tree. Not everyone wants to
use u-boot on Sandybridge systems, however.
Since the new code (based on Kconfig) is now fully working, we
can drop the u-boot device tree remnants.
Change-Id: I4e012ea981f16dce9a4d155254facd29874b28ef
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1051
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The MRC region is described by Kconfig variables, no further math
or parsing is required at this point.
Change-Id: I290d8788b69ef007e9ea2317ce55aefa2d791883
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1046
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Requirements:
- must be in ramstage (locking flash while executing code from there
might not work)
- must be after cbmem is reinitialized (so the mrc cache copy of the
current run can be found)
Change-Id: I8028fb073349ce2b027ef5f8397dc1a1b8b31c02
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1002
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Separate Sandybridge from ChromeOS a bit
The Sandybridge code depends on chromeos features a whole lot.
As a first step, provide a code path to look up the MRC cache
without depending on u-boot.
- Move mrc cache handling to separate file
This enables us to handle the MRC cache from ramstage,
where we can write the flash safely (eg. to update the
cache).
Also teach it to lookup the current MRC cache from CBMEM,
as the original data block isn't available anymore.
After all the preparations, finally write to the SPI
as necessary. It's a simple round robin wear levelling
that erases the entire MRC cache region when it's full
and starts from the beginning.
Change-Id: I4751385574cf709b03d5c9d153b7481ffc90ce12
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1001
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Replace #if CONFIG_FOO==1 with #if CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*1[[:space:]]*\$,#if \1," {} +
Replace #if (CONFIG_FOO==1) with #if CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*1)[[:space:]]*\$,#if \1," {} +
Replace #if CONFIG_FOO==0 with #if !CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*0[[:space:]]*\$,#if \!\1," {} +
Replace #if (CONFIG_FOO==0) with #if !CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*0)[[:space:]]*\$,#if \!\1," {} +
(and some manual changes to fix false positives)
Change-Id: Iac6ca7605a5f99885258cf1a9a2473a92de27c42
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1004
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
Change-Id: I9217a75ec1a0abb898c45752d990231ce98e5fb2
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/991
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: If183611b0b62d9321a5a12311c4cb3b344b04b36
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/986
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This fixes my build when specifying an absolute path to the binary.
Change-Id: I95fb3960be70f78146c6afeb9cc777dccdca6b5b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/987
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
It is important to have the system configuration reported as early as
possible to have a better idea what exact chipset the platform is
running with.
This change adds code to have an early coreboot module report the CPU
and PCH information. CPU info includes the 32 bit feature information
word, the symbolic processor brand string, and information about some
features support, as obtained through CPUID instructions.
The PCH information includes the symbolic device name and PCI device
version.
Change-Id: If6c21ad5ffb76d7d57d89f4f87d04bdd7192480a
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/975
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
- New table for GT1
- Updates to GT2 17W table
- New table for GT2 35W SKU
- New table for GT2 Other
This also includes a workaround to poll on a different register
when deasserting force wake. On some SKUs the kernel is hanging
when bringing up graphics unless this register is also polled.
Change-Id: I2badf62b464e901cfb0eaf4fc196f59111c71564
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/974
Tested-by: build bot (Jenkins)
|
|
- Add config options to set backlight registers
- Update powermeter weight tables for IvyBridge GT1 and
add a new table for GT2 SKU
- Fix a few registers used during GPU PM init sequence
Change-Id: I1500bc07e3ba1bc10c77e7856089e716489dc07a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/973
Tested-by: build bot (Jenkins)
|
|
This is done inside the SystemAgent binary on Ivybridge.
Change-Id: I8fb0f593a65a4803e160b284c21b9d5021e2e4a0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/970
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The ASPM setting for the Direct Media Interface should no longer be done on
Ivybridge/PantherPoint based systems.
Change-Id: Id30de1beb1b162564048e76712736ccf7049dc7c
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: http://review.coreboot.org/969
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This fixes a few cosmetics with the following three boards:
- Intel Emerald Lake 2
- Samsung ChromeBook
- Samsung ChromeBox
The following issues were fixed:
- rely on include path in ASL code instead of specifying relative
paths
- use updated ALIGN_CURRENT in acpi_tables.c
- use preprocessor defines instead of hard coded values where possible
Change-Id: Ia5941be3873aa84c30c13ff2f0428d1c52daa563
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/963
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
|
|
This code is still using libfdt which was denied for inclusion
in coreboot, so it won't compile as is.
Without MRC cache, waking from suspend won't work, and cold boots are
significantly slower (adds around 300-400ms per channel IIRC).
A rework of this code is currently in the works, but will take a little bit
more time (and should not hold back the mainboards being merged)
Change-Id: Ifb9e7d7b86c1f52378803a748810da0d51b58384
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/948
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- When calling map_oprom_vendev() the vendor ID and device ID
are joined into a 32 bit value. They were reversed from the
order that I would have expected - Device ID as the high 16 bits
and the Vendor ID as the low 16. This patch reverses them so
so that the the dword comparison in map_oprom_vendev() matches
what's entered into Kconfig for vendor,device.
- Change files calling map_oprom_vendev()
Change-Id: I5b84db3cb1a359a7533409fde7d05fbc6ba3fcc4
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/938
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Cougar Point southbridge does udelay in SMM, hence add it on Sandybridge
systems.
Change-Id: I6e5520ca27e7c6eaae632992fb68612067bc1e30
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/937
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
No longer include northbridge files directly in the source for
mainboard romstage.c and fix includes.
Also make required adjustments to function declarations.
Change-Id: Iafdcc0766ed44c64cc628e5935eef2c6372f5f22
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/906
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
It takes about 3 seconds to scrub 8GiB DDR266 RAM.
After ECC scrub XIP cache is disabled for system stability. There is
very little to do in romstage after ECC scrub, especially when RAM
debug messages are turned off. So the delay caused by this is hardly
noticeable.
Cache for complete ROM is re-enabled before ramstage is decompressed,
and it has no unstability issues. So the code required to re-enable
cache for ROM currently already exists in cache-as-ram_ht.inc.
A Kconfig option HW_SCRUBBER enables the scrub to be run on hard
reboots and power-ons.
Change-Id: Icf27acf73240c06b58091f1229efc0f01cca3f85
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/905
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|