| Age | Commit message (Collapse) | Author |
|---|
|
pci_bus_default_ops() is the default anyway.
Change-Id: I5306d3feea3fc583171d8c865abbe0864b6d9cc6
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/26055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change also makes sure that the sum the uma regions (TSEG, GSM,
GSM) is 4MiB aligned. This is needed to avoid cbmem_top floating between
2 usable ram region, since cbmem_top is aligned 4MiB down to easy MTRR
setup for ramstage. At least tianocore requires this and fails to boot
without it.
Better MTRR are achieved by making the memory 'hole' till 4GiB exactly
2Gib.
This code mimics how it is done in nb/intel/gm45 and achieves similar
results.
TSEG is enabled and set to 8M since this makes it easier to reuse the
common smm setup / parallel mp code and makes it possible to cache the
ramstage in there like how it's done on newer targets.
TESTED on Intel DG43GT.
Change-Id: I1b5ea04d9b7d5494a30aa7156d8c17170e77b8ad
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Programming CxDRB should be cumulative as explained in "Intel ® 4
Series Chipset Family datasheet".
This does not seem to have any real impact but better do according to
the documentation and what vendor firmware does.
This also removes some dead code.
Change-Id: I7ff3264824c843f84b9eb6c06a06aa3f151fe4b3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22911
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This training find the optimal write DQ delay and read DQS delay
settings. It does so on all lanes at the same time, like
vendor (training each lane individually has poor results).
The results are stored in the sysinfo struct and restored on next
boots and S3 resume.
This potentially increases stability as optimal settings are chosen
and is more necessary for DDR3 raminit where the write DQS delays are
leveled/variable due to the flyby topology.
TESTED on Intel DG43GT with (2G + 1G) on each channel, see that the
results are quite close to the safe original ones (that previous
worked fine) and tested with memtest86+.
Change-Id: Iacdc63b91b4705d1a80437314bfe55385ea5b6c1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Use of `device_t` has been abandoned in ramstage.
Change-Id: Ib3e708a7fa9f0a78dc704a502a2f01ee0fe209ae
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This variable needs to be in byte so a division by 8 needs to happen.
This problem was introduced by 3cf94032b "nb/x4x/raminit: Rewrite SPD
decode and timing selection", but was probably not encountered because
such dimms are rather uncommon.
Change-Id: I2d57f5e584ac7fa1479791c239432005fe8c178d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22991
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Displaying the whole receive enable procedure is very verbose should
only be done if CONFIG_DEBUG_RAM_SETUP is selected.
Change-Id: Ib568621e6d044624c1c0aeb6fb08945f561395c7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
During raminit a lot of procedures need to be done for each bytelane.
Change-Id: Ib9a30ffabaf5c845e962e3e79cf4a20faa1d9857
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This replaces magic values by macros and adds some comments to improve
readability.
Adds a convenient function to fetch the test address of a rank.
Also fixes the temporary memory map by changing a write to MCHBAR
0x100 to 0x110, since this is what vendor does. (No difference
observed thus far)
TESTED on DG43GT
Change-Id: I58923e4a8a756f4ae65f759e7d46e03fad39fab7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
|
This patch pushes these large default delay tables to a different file
to reduce cluttering up the actual raminit source. While doing so it
also uses more but smaller arrays and also adds the respective default
delays for DDR3 which are not yet used in this patch.
This patch add a function to set the read DQS delays instead of just
programming magic values. (This will prove useful for DQS read
training)
To prepare for adding trainings on the delay values it stores these
default delays in the sysinfo struct to program those. Later when
trainings are implemented those trained values will be used instead of
these safe default values, via using the cached sysinfo in 'mrc'
cache.
TESTED on DG43GT (still works fine)
Change-Id: I0e3676e06586ea84fc0729469946dbc9a8225934
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Stores information obtained from decoding dimms and receive enable
results for future use.
Depreciates using rtc nvram to store receive enable settings.
A notable change is that receive enable results are always reused, not
just on a resume from S3.
This requires cbmem to be initialized a bit earlier, right after the
raminit finished to be able to add the sysinfo struct to cbmem which
gets cached to the SPI flash in ramstage.
TESTED on Intel DG43GT with W25Q128.V. With 4 ddr2 dimms time in
raminit goes from 133,857ms (using i2c block read to fetch SPD) to
21,071ms for cached results.
Change-Id: I042dc5c52615d40781d9ef7ecd657ad0bf3ed08f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21677
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
In order for ddr2.h and ddr3.h to be included in the same file it
cannot have conflicting definitions, therefore rename a few things and
move some things to a common header.
Change-Id: I6056148872076048e055f1d20a60ac31afd7cde6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
|
The result is shorter and (IMHO) more readable code.
Change-Id: Ic51c05d7aa791250d775bd7a640213065d4caba0
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/23710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Especially on ICH7 failing to do so results in i2c block read being
unusable. On ICH10 this problem doesn't manifest itself that much.
This moves disabling the watchdog reboot to the northbridge code like
i945 (even though it technically is southbridge stuff).
TESTED on Intel DG41WV: hacking on raminit is much nicer since no
need to do a hard power down for +4s are needed to clear the timeouts.
Change-Id: Icfd3789312704f61000a417f23a121d02d2e7fbe
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This is mostly written from scratch and uses common spd ddr2 decode
functions.
This improves the following:
* This fixes incorrect CAS/Freq detection on DDR2;
* Fixes tRFC computation; tRFC == 78 is a valid timing which is
excluded and 0 ends up being used; (TESTED)
* Timings selection does not use loops;
* Removes ddr3 spd decode and is re-added in follow-up patches using
common ddr3 spd functions;
* Raminit would bail out if a dimm was unsupported, now in some cases it
just marks the dimm slot as empty;
* It dramatically reduces stack usage since it does not allocate 4
times 256 bytes to store full SPDs, amongs other unused things that
were stored in sysinfo;
* Reports when no dimms are present;
* Uses i2c block read to read SPD which is about 5 times faster than
bytewise read, with a fallback to smbus mode in case of failure,
which does seem to happen when the system is forcefully powered
off.
Change-Id: I760eeaa3bd4f2bc25a517ddb1b9533c971454071
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This fixes some bitwise logic errors that caused the coarse offset not
to be programmed.
This fixes a regression introduced by 6d7a8c
"nb/intel/x4x/raminit: Rework receive enable calibration"
where the coarse offset doesn't get programmed anymore.
TESTED on Foxconn g41s-k on a DIMM where the final DQS receive enable
delays are close but above and below the edge of a coarse delay setting.
Change-Id: I41869815f782a2ea1178bdea006e3a7587441323
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Port the ACPI opregion implementation that resides in
drivers/intel/gma to older platforms.
It allows to include a vbt.bin and allows GNU/Linux to load the
opregion as ASLS is being set.
Windows' Intel will likely ignore it as it relies on legacy VBIOS
to be loaded at 0xc0000.
Tested successfully on DG43GT (x4x) with vbt.bin,
with X200 (gm45) with vendor option rom and
D945GCLF (i945) with fake vbt.
Change-Id: I1896411155592b343e48cbd116e2f70fb0dbfafa
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/21766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Needed for coreboot spi driver.
Change-Id: I01059c8cbdc6a002dfd75b6da3a629811b137702
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
A small typo in the dll setting code prevented this combination from
booting.
TESTED on ga-g41m-es2l with 800MHz FSB CPU and 667MHz ddr2
Change-Id: Ib013471773c20336ba0902b7f328bfb6ef970747
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Moves receive enable calibration to a separate file to lighten
raminit.c a bit.
Receive enable calibration is quite similar to gm45 so it reuses some
of its function names.
The functional changes are:
* the minimum coarse is now reset for each channel;
* on the second fine search for DQS high, TAP overflow is handled by
increasing medium;
* start coarse at CAS + 1 instead of CAS - 1. Other Intel northbridges
do the same and the results are more in line with register dumps
from vendor bios.
These might improve stability.
TESTED on ga-g41m-es2l
Change-Id: I0c970455e609d3ce96a262cbf110336a2079da4d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This allows the use of the native VGA init on boards featuring DVI-I
ports. Digital output is not supported.
Change-Id: I11a4dd68746e06c7e27ecf3e765bdd0d8cf40515
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I885b6bd9f5be6b4e3696a530016123a3e81c4b10
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This does the following:
* Clarify that settings are set to the same value for each rank;
* Allows to program coarse
* Fix some style issues like white spaces between arithmetic
operators.
Change-Id: I3a9e28cfec915a0bb15789c23bea259f621b5096
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ic9226098dafa2465aa5fccc72c442de2b94e44c7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Rename `FRAMEBUFFER_KEEP_VESA_MODE` to `LINEAR_FRAMEBUFFER` and put
it together with new `VGA_TEXT_FRAMEBUFFER` into a choice. There are
two versions of `LINEAR_FRAMEBUFFER` that differ only in the prompt
and help text (one for `HAVE_VBE_LINEAR_FRAMEBUFFER` and one for
`HAVE_LINEAR_FRAMEBUFFER`). Due to `kconfig_lint` we have to model
that with additional symbols.
Change-Id: I9144351491a14d9bb5e650c14933b646bc83fab0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Like HAVE_VGA_TEXT_FRAMEBUFFER, these are selected by graphics drivers
that support a linear framebuffer. Some related settings moved to the
drivers (i.e. for rockchip/rk3288 and nvidia/tegra124) since they are
hardcoded.
Change-Id: Iff6dac5a5f61af49456bc6312e7a376def02ab00
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
* Rename it to HAVE_VGA_TEXT_FRAMEBUFFER.
* Let drivers select it if they are in charge.
* Don't select it on the mainboard level if a driver handles it.
Change-Id: I2d9d09be9aa6d019e77460e69a245ad2d8cda4ea
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
It could end up not initialized which causes it not to build with
clang.
Change-Id: I3be9477d836123aaa87c9bebb41c1ec34689a771
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19736
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This makes the code more readable since it avoids messing with two
dimensional arrays and needing remember what the indices mean.
Also introduces an unused coarse element which is 0 for all default
DLL settings on DDR2.
Change-Id: I28377d2d15d0e6a0d12545b837d6369e0dc26b92
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Hides JEDEC steps using the RAM_SPEW macro.
Also hides a hexdump of SPDs.
Change-Id: Ie2b484cf1f1d296823df0473e852d9d07ca20246
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18924
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
It is not really known why there is such a long delay, but it works
fine without it.
TESTED on ga-g41m-es2l.
Change-Id: Idff5b978bbf161f8520d8000848e7b11c98c3945
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19514
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
A left-over from 5e3cb72a71 (nb/x4x: Do not enable IGD when not
supported). Should fix coverity issue 1375009. Remove a redundant
line that uses the variable `gfxsize` out of its scope and move the
variable declaration. Make sure the variable is always initialized,
drop unneeded error-handling for `get_option()` and sanitize the
read value instead.
Change-Id: Iee2beda30d8c74df0f412622c3ff3357819e386b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19680
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Currently only one board uses this northbridge in coreboot but some
patches are pending to add more.
Change-Id: If035e442d1a23674667f46a07b44c4f2b81be48c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Is only present on the P45 subtype of chipset.
Change-Id: I6b138db6654c83c40b5ca4b65d6ccd51ad4277fa
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18516
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
According to "Intel ® 4 Series Chipset Family datasheet" in the
description about GGC and DEVEN, CAPID0 bit46 is said to reflect the
presence of an internal graphic device. This would allow the P43 and
P45 chipset variants to work.
Change-Id: Icdaa2862f82000de6d51278098365c63b7719f7f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18515
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The NGI writes to legacy VGA registers which should not happen when
VGA cycles are assigned to a different device.
TESTED on ga-g41m-es2l
Change-Id: I0a03e35c0d7f2532edd6cc5e62d1cf07dab57f60
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This disables VGA cycles on IGD when an external VGA device is
found. This allows PCI or PCIe devices to be the 'main' VGA device if
found, while the IGD is still available.
TESTED on ga-g41m-es2l: SeaBIOS shows payload on external GPU while
linux (4.10) can use both as a framebuffer simultaneously without any
extra configuration.
Change-Id: I74890918feb0f1ff6b971c4aaa96f1f7b75266ac
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18504
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Computes TSEG size dynamically.
Changes the size of legacy hole to match other Intel northbirdges.
Refactor this a little by needing one less variable.
Change-Id: I0e6898c06a2bc1016eeaa3f002ff6c39657018ae
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This code ought not to run if ME is disabled. It also prohibits
writing to some GMCH regs like GGC bit1.
Intel ® 4 Series Chipset Family datasheet refers to this as
"ME stolen Memory lock" without actually describing this
functionality.
Change-Id: Iaa8646e535e13c44c010ccd434a5af954cf7dfbc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The checkreset() function checks if raminit previously
succeeded (pmcon2 bit7 == 0). If this is not the case it will issue a
hot reset (writing 0x6 to 0xcf9). On the next attempt to boot the
system BOOT_PATH_RESET path will be taken. This boot path can only
successfully initialize memory if the system was reset from a state
where raminit succeeded, which is not the case here.
This can be fixed by issuing a cold reset instead of a hot reset.
Change-Id: Idbcf034c3777a64cc3fb92dc603d10470a6c8cb6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The x4x northbridge can be paired with either an ICH7 (in the case of
g41) or an ICH10 (all other cases: g45, q45, p45, ...). Only ICH10
sometimes occurs with a descriptor, gbe and an ME region.
ICH7 is always descriptorless so it makes no sense to fix CBFS to
accommodate for those other objects.
Change-Id: I4a01dfdbce1807e44932a3ac812110382332abd8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19181
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
It makes no sense to read SPDs if the system will reset anyway.
Change-Id: Id2ad9b04860b3e4939a149eef6b619a496179ff8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17661
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ie22b8bd5420f8c33df1866410af42ef41ad38362
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18694
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
It rewrites the results of receive enable stored in the upper nvram
region, to avoid running receive enable again.
Some debug info is also printed about the self-refresh registers.
(Not enforcing a reset here, since 0 does not necessarily mean it's
not in self-refresh).
Change-Id: Ib54bc5c7b0fed6d975ffc31f037b5179d9e5600b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17998
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Previously the raminit failed on hot reset and to work around this
issue it unconditionally did a cold reset.
This has the following issues:
* it's slow;
* when the OS issues a hot reset some disk drives expect their 5V
power supply to remain on, which gets cut off by a cold reset,
causing data corruption.
To fix this some steps in raminit must be ommited on the reset path.
This includes receive enable calibration.
To achieve this it stores receive enable results in RTC nvram for them
to be rewritten on the resume path.
Note: The same thing needs to be done on the S3 resume path.
Calling a hot reset after raminit "outb(0x6, 0cf9)" works.
Change-Id: I6601dd90aebd071a0de7cec070487b0f9845bc30
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18009
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The results were obtained by comparing the MCHBAR registers of vendor bios
with coreboot at the same dram timings.
This fixes 2 issues:
* 1333MHz fsb CPUs were limited to 667MHz ddr2 speeds, because with
800MHz raminit failed;
* 1067MHz fsb CPUs did not boot when second dimm slot was populated.
TESTED on ga-g41m-es2l on 800, 1067 and 1333MHz CPUs with
DDR2 667 and 800MHz dimms.
Change-Id: I70f554f97b44947c2c78713b4d73a47c06d7ba60
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18022
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Nothing from that header is used or even declared since
CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT is not selected on Intel
hardware.
Change-Id: I9101eb6ffa6664a2ab45bc0b247279c916266537
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18044
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
Currently only there is only one eaglelake board in coreboot
(ga-g41m-es2l) featuring a G41 variant northbridge.
Adding boards with a different variant (Q43, Q45, G43, G45, B43) will
require this change for graphic initialisation.
Change-Id: Ida32c563a99576b66685dfdadf9a534fd6e197dc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17900
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I2085fc3a17d32cfbdab9ec0b7afbc01031e75b47
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17785
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Adapt implementation from skylake to prepare for removal of
HIGH_MEMORY_SAVE and moving on to RELOCATABLE_RAMSTAGE.
With this change, CBMEM region is set early-on as WRBACK
with MTRRs and romstage ram stack is moved to CBMEM.
Change-Id: Idee5072fd499aa3815b0d78f54308c273e756fd1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15791
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Force modest 4 MiB alignment to help with MTRR assignment.
Change-Id: I49a7d1288bc079da1b8bd52150ddcfcfe2e51179
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17780
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
We have kconfig.h auto-included and it pulls config.h too.
Change-Id: I665a0a168b0d4d3b8f3a27203827b542769988da
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17655
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Also remove separate MMCONF_SUPPORT_DEFAULT flag.
Change-Id: Idf1accdb93843a8fe2ee9c09fb984968652476e0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17694
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I9b952e32dc661f5c1fa96b037b415693d8777b04
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17685
Tested-by: build bot (Jenkins)
Reviewed-by: Damien Zammit <damien@zamaudio.com>
|
|
Fix-up for 696abfc
nb/intel/x4x: Fix and deflate `dimm_config` in raminit
It didn't fix the channel-number shifting issue as intended.
The channel index is either 0 or 1. DIMMs are counted from 0
to 3 where 0..1 covers channel 0, and 2..3 covers channel 1.
Since we have two DIMMs per channel, we have to multiply the
channel index by 2 (or shift it left by 1) to get the index
of the first DIMM in the channel. Finally, to get the offset
of a DIMM in the channel we take its index modulo 2 (again,
the number of DIMMs per channel).
Change-Id: I2784b0cb655bfe823bf5fa48b722623dfca1ddc3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/17612
Tested-by: build bot (Jenkins)
Reviewed-by: Damien Zammit <damien@zamaudio.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
By shifting the `chan` right instead of left, values were always taken
from the DIMMs of the first channel. The diff-stat also looks like an
improvement.
Change-Id: I605eb4f9b04520c51eea9995a2d4a1f050f02ecc
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/17587
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Damien Zammit <damien@zamaudio.com>
|
|
Make MMCONF_SUPPORT selected with MMCONF_SUPPORT_DEFAULT.
Platforms that remain to have explicit MMCONF_SUPPORT are
ones that should be converted.
Change-Id: Iba8824f46842607fb1508aa7d057f8cbf1cd6397
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17527
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I4a8297397d878e38516c8df19dd311c7ef19ec06
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17478
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Have a common romstage.c file to prepare CAR stack guards.
MTRR setup around cbmem_top() is somewhat northbridge specific,
place stubs under northbridge for platrform that will move
to RELOCATABLE_RAMSTAGE.
Change-Id: I3d4fe4145894e83e5980dc2a7bbb8a91acecb3c6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15762
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I3f692c55fdff99aa9eb41eaaea79a41ac93be590
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17170
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Those registers are only used on more recent Intel platforms featuring a
PCH. The DP registers on G4X hardware are at a different offset.
Change-Id: I4660e547426ccec0b2095d897e4a8c86e0acf41e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17111
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This removes writes to FDI related registers since there is no FDI
link on these targets. This is likely a remainder from copying code from
later targets.
TESTED on Thinkpad x200 (gm45)
Change-Id: Id67fdc999185fa184a9ff0e5c3fc9bced04131ad
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16993
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
This issue was found by Coverity Scan, CID 1364118.
Change-Id: Iba3c0f4f952729d9e0987d928b63ef8b8fe8841e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16992
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
According to: "Intel ® 965 Express Chipset Family and Intel ® G35 Express
Chipset Graphics Controller PR" the p2 divisor needs to be 10 when the
dotclock is below 225MHz and 5 when its above 225MHz.
Change-Id: I363039b6fd92051c4be4fdc88788f27527645944
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16991
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I2b8c4ef75cca9f9d5251789cda4187a02076b69d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16964
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch implements native resolution, VESA mode, on the VGA output of
x4x.
It relies on EDID to modeset, but has a fallback-mode (640 x 480 @
60Hz) if this is no EDID could be found. This fallback mode only works
in textmode since in VESA mode some payloads (grub2) rely on VBE info,
which is being generated from an EDID.
Change-Id: I247ea7171ba3c5dc3b209d00e4dcb2d2069abd75
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16498
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ib06ecd083f00c74f1d227368811729d2944dd1ef
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16851
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Padding the VBT id string is now done automatically.
Change-Id: I8f9baf7b1585026bc29b82d07e451aa11e284ffb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16740
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Iffa058d9eb1e96a4d1587dc3f8a1740907ffbb32
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16414
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Replace the use of the old device_t definition inside
northbridge/intel/x4x.
Change-Id: I65cd02eacf57cb41ded434582ca6e9d9f655e6ea
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16472
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Device 1 on secondary bus instead of device 0 was being routed.
Change-Id: I4207938038acf7ff941afd692e90a690d2426a05
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16515
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I389c4630362af1c1bf6d281c9d2b7fc81bea2d5d
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16495
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is necessary for PCI express graphics card add-ons,
otherwise the pci allocator cannot fit the mmio for the
add on card into the space it has available and the OS
turns off the card. Old value was 1GiB.
Change-Id: I606994501b15e636fe209d1ed4b3d3f73b42bf5c
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16494
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
No more hang on DMI init when wait for DMI is re-enabled.
Previously the virtual channel arbitration table was not being
set up in the south/north bridges causing invalid DMI state.
This has been tested on GA-G41M-ES2L with patches following.
An NVIDIA GT218 card was detected by the OS and displayed using
the nouveau driver with no blobs.
Change-Id: I35e03c40f5f7aa4915afd5d26db7ab053abcf0cd
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16491
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I53208ce5db06d2c65f954e6d59222924ab87722e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16304
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This allows to set the preallocated memory for the IGD on x4x
using a cmos option.
If no cmos option is found a default value of 64M is used.
TESTED most options on ga-g41m-es2l with 2G dimm in one slot and 2x2G.
352M also works in contrast with gm45 where it is known to cause issues
with certain ram combinations.
Change-Id: I9051d080be82f6dfab37d353252e29b2ed1fca7f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/15492
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The Intel documtentation, "Intel ® 4 Series Chipset Family"
mentions the possibility of 1, 4, 8 and 16M of preallocated
memory for the IGD, but does not document this.
This allows to set those undocumented values.
TESTED on ga-g41m-es2l with 2G dimm in one slot and 2x2G.
Change-Id: I92beb8d78907d4514a5aaf69248dd607dcf227c0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/15491
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Now hardcode maximum memory frequency capability to 800MHz, as
all chipsets in x4x family support PC2-6400 according to the datasheet.
CAS latency detection also relies on this, and has been cleaned up.
Ram initialization does not work with FSB 1333MHz / DDR2 800MHz combination,
so disable this combination for now, and reduce to 667MHz instead.
Still don't know why this is the case, but FSB1333/667 works.
These changes should now allow existing configurations to continue working,
while providing support for previously unworking configurations, due to
previous buggy CAS latency detection code.
TESTED: on GA-G41M-ES2L
CPU: E5200 @ 2.50GHz (FSB 800MHz)
2x 1GB 667MHz hynix worked @ 667
1x 2GB 800Mhz ARAM worked @ 800
1x 1GB 667Mhz StarRam worked @ 667
2x 2GB 800Mhz (generic) worked @ 800
Change-Id: I1ddd7827ee6fe3d4162ba0546f738a8f9decdf93
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/15818
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Fix and use the failsafe CAS detection logic rather than
recalulating the values from raw SPDs.
Tested on GA-G41M-ES2L with 2x2GB DDR2-800 DIMMs
(which worked before and still work)
Change-Id: I6af0f1705d099f7bcbff8c9baa94a68dae689e01
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/15726
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
If S3 support was implemented for this platform later on, use
romstage handoff structure instead.
Change-Id: I03c1e07a7fcc17c27203d0c4e32e3958f2ba5273
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15716
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Damien Zammit <damien@zamaudio.com>
|
|
Previously, any 800MHz DIMMs were being slowed to 667MHz
for no reason other than there was a bug in the maximum
frequency detection code for the MCH.
Change-Id: Id6c6c88c4a40631f6caf52f536a939a43cb3faf1
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/15257
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Previously, 0x0 was the value being used for an unpopulated dimm
on spd[62], however some DDR2 dimms have 0x0 as a valid value.
Now use 0xff which is an unused value even on DDR2/DDR3.
Change-Id: I55a91a6c3fe3733a7bb2abc45ca352c955c07c99
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/15058
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The values were obtained from vendor bios at runtime.
I am not 100% sure of the sequence required to initiate them,
but guessed from the gm45 code. There may be some status bytes
needed to be polled during the sequence that is missing,
but as I don't have bios writer's datasheet it's very hard
for me to know.
Change-Id: Idd205e0bab5f75e01c6e3a5dc320c08639f52db8
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/14925
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We want the question for CBFS size to be next to the rom size in the
mainboard directory, but that doesn't seem to work for how people
want to set the defaults. Instead of having the list of exceptions
to the size, just set the defaults at the end of kconfig.
- Move the defaults for chipsets not setting HAVE_INTEL_FIRMWARE into
the chipset Kconfigs (gm45, nehalem, sandybridge, x4x)
- Override the default for HAVE_INTEL_FIRMWARE on skylake.
- Move the HAVE_INTEL_FIRMWARE default setting into the firmware
Kconfig file
- Move the location of the default CBFS_SIZE=ROM_SIZE to the end of
the top level kconfig file, while leaving the question where it is.
Test=rebuild Kconfig files before and after the change, verify that
they are how they were intended to be.
Note: the Skylake boards actually changed value, because they were
picking up the 0x100000 from HAVE_INTEL_FIRMWARE instead of the
0x200000 desired. This was due to the SOC_INTEL_SKYLAKE being after
the HAVE_INTEL_FIRMWARE default. Affected boards were:
Google chell, glados, & lars and Intel kunimitsu.
Change-Id: I2963a7a7eab037955558d401f5573533674a664f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/13645
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Previously with errors in the ram init, early cbmem was disabled.
Now that the ram is working correctly, set as early cbmem platform
and update all (1) boards to use it.
Tested on GA-G41M-ES2L
Change-Id: I5925c28821537f0e326b4f5a2ac39778e4724a3c
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13131
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Tidy up the code and move vga_textmode_init() later
Change-Id: I49967e7197416c955ae6c8775eac7d1a60c92d1c
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13128
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
- Fix bug with msbpos, it was not returning the correct result
due to typo in logic, and unsigned value needed to be negative.
- Add reclaim above 4GiB
- Fix to ME related registers near the end of raminit
Change-Id: I04acd0593a457437ee4a42e14b287b2b17a160af
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13127
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
- Add device enable macros
- Set the PMBASE correctly through southbridge device
Change-Id: I1b8cc3de96b1ecaf01e31bad8fba1fada8671c2d
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13126
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Previously, 0xa0000000 to 0xc0000000 needed to be reserved as
a non-usable memory hole because it would hang on memory i/o.
Memtest86+ now passes with no errors on both channels populated.
Tested on GA-G41M-ES2L with 2x2GiB sticks of ram.
Change-Id: Ib52a63a80f5f69c16841f10ddb896ab3c7d30462
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13125
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
- Don't redefine D0F0_PCIEXBAR_LO, use the #define in x4x.h
- Move TPMBASE and TPM32() definitions into iomap.h
- Use "" style include for x4x.h in nortbridge files.
- Move includes of .h files out of x4x.h and into the c files that need
them.
- Protect function definitions in bootblock.
Change-Id: I3fdb579235c5446733a0ffba05fffe1a73381251
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12849
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
- occured -> occurred
- accomodate -> accommodate
- existant -> existent
- asssertion -> assertion
- manangement -> management
- cotroller -> controller
Change-Id: Ibd6663752466d691fabbdc216ea05f2b58ac12d1
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12850
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Passes memtest86+ with either one or two sticks of 2GB ram
but memory map needs a hole at 0xa0000000 to 0xc0000000
Change-Id: Ib34d862cb48b49c054a505fffcba1c17aeb39436
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/11307
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Boots to console on Gigabyte GA-G41M-ES2L
Ram initialization *not* included in this patch
VGA native init works on analog connector
Change-Id: I5262f73fd03d5e5c12e9f11d027bdfbbf0ddde82
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/11305
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
