| Age | Commit message (Collapse) | Author |
|---|
|
All X11 boards currently supported have Intel SPS without support for
S3/S5. Thus, drop it from Kconfig.
Note: not all X11 boards are server boards. When a X11 desktop or
workstation board should be added, this can be selected by the boards,
where S3/S5 work.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ie75c9217078d38c42eba2b30c078b8bb1c2ca694
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Correct unconnected pads that are configured different currently by
copying vendor configuration while porting the board.
Add internal pull resistors to all unconnected pads, that do not have an
external pull resistor, to prevent floating.
The pads have been determined by dissecting a dead board. This commit
only changes pads, that are not connected at all and don't have any via,
so we can be absolutely sure there is no other connection.
Change-Id: I991fe270b42f430f7447712236e0f80b3d5bba2a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
(Re)configure various pads found by dissecting a dead board and vendor
firmware, as well as the BMC firmware:
- GPP_B14: input connected to jumper JBR1 - could be used to implement
"BIOS Recovery" ("Top-Block Swap") functionality; external pull-up
- GPP_C20: output to BMC alert CPU_THROTTLED# - can be used to notify
the BMC about a thermal throttling event. Not implemented in vendor
firmware.
- GPP_C23: input connected to the CPU's CATERR# output; external pull-up
Not actively used by vendor firmware.
- GPP_D1: output connected to on-board and front panel power LEDs
- GPP_D18: output connected to PERST# of both CPU PCIe Slots. Can be
used for testing/debugging only, since it resets both slots at once.
Not actively used by vendor firmware.
- GPP_D19: output connected to PERST# of both PCH PCIe Slots. Can be
used for testing/debugging only, since it resets both slots at once.
Not actively used by vendor firmware.
- GPP_D22: input connected to the BMC enable/disable jumper JPB1; Will
be used later in CB:48096 and CB:48097; external pull-up
- GPP_G0 - GPP_G3: dedicated/integrated CPU switching; probably not
useful, since the IGD is not connected to any ports on this board.
External pulls ensure correct function of a dGPU even without driving
the gpios. Not used by vendor firmware.
- GPP_G12 - GPP_G16: inputs for binary SKU_ID; external pulls
- GPP_G20: PWRFAIL# input from JPI2C1 (pin 3); external pull-up; Not
used by vendor firmware.
Also add comments for documentation. While at it, mark ME-owned pads as
reserved.
Change-Id: I9f9328e9ce6f7e291b171f776bb98bc617b64b93
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
add new Synaptics touchpad for volta.
BUG=b:174802144
TEST=emerge-volteer coreboot and check touchpad function work.
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I7fc8d08b8b2229ca9252618f159fc9c6f91f9d7f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48395
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change reorganizes FMAP for volteer to make use of the lower
16MiB of the SPI flash for RW_SECTION_A and RW_MISC in addition to
RW_LEGACY. This is now possible because TGL supports memory mapping of
BIOS region greater than 16MiB.
Following changes are made in chromeos.fmd as part of this:
1. Move RW_SECTION_A and RW_MISC to lower 16MiB.
2. Reduce size of RW_LEGACY to 2MiB since we longer need to use it as
a placeholder in the lower half of the SPI flash.
3. Reduce size of RW_ELOG to 4KiB as coreboot does not support a
larger region for ELOG.
4. Increase WP_RO to 8MiB to allow larger space for firmware
screens. GBB size is thus increased to 448KiB.
BUG=b:171534504
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I0c3c0af94183a80c23d196422d3c8cf960b9d9f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
AP_PEN_DET_ODL isolated by a diode and need to pull up internally.
BUG=b:160752604
BRANCH=dedede
TEST=Build and confirm waveform by google EE parter.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I85f3d0209094af07891a5c0cc218443da586e6e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48294
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update telemetry settings.
VDD Slope : 32643 -> 26939
VDD Offset: 208 -> 125
SOC Slope : 22742 -> 20001
SOC Offset: -83 -> 168
BUG=b:171668654
BRANCH=zork
TEST=1. emerge-zork coreboot
2. pass AMD SDLE test report
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Ic63e069310aa4a66cd4c9058790dbed37e6967f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48288
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the PMC MUX and CONx devices for adlrvp for
conn2.
BUG=b:170607415
TEST=Built and booted adlrvp. Verified the PMC.MUX CONx objects
in SSDT tables.
Change-Id: I52afbd429750cfa416f4ed93aeb1be590f8c3a5c
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48230
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Elan and Synaptics touchpad settings.
BUG=b:169813211
BRANCH=None
TEST=build metaknight firmware
Change-Id: Ice0a86cd5610db269d44acb1d51cb652110d9b0c
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47441
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raymond Wong <wongraymond@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add HDA,speaker codec and speaker amp settings.
BUG=b:169813211
BRANCH=None
TEST=build metaknight firmware
Change-Id: I9b1057eac94b568914f17fcccee58a0e403ccec0
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raymond Wong <wongraymond@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This change restricts RW_DIAG region to lower 16MiB to ensure that the
extended BIOS checker for FMAP does not complain about 16MiB boundary
crossing.
I haven't updated any other regions to occupy the newly freed space
but it is fine since this board is dead and should be dropped from
coreboot soon.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I19ab204fbe3e020e42baf68bfa350dcff32066a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change restricts SI_ME region to live below the 16MiB boundary to
ensure that no regions cross the 16MiB boundary as the extended BIOS
window checker for FMAP complains about it.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib0838ff4c63b06b8dc169b40d3022965b2f2f8f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
disabling DDI port 1 and 2 HPD.
This patch adds the PMC MUX and CONx devices for lindar. Device
specific method contains the port and orientation details used
to configure the mux.
BUG=b:172533907
BRANCH=firmware-volteer-13521.B
TEST=Built and booted into OS.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Id5ee78b7ece8421144086af9b95f5f0d849be56c
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
SATA_AHCI is already the default mode for CNL based mainboards.
Therefore, remove its configuration from all related devicetrees.
Built clevo/l140cu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: I814e191243224a4b021cd7d4c1b611316f1fd1a4
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Align the SATA mode names with soc/skl providing a consistent API.
Built clevo/l140cu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: I54b48462852d7fe0230dde0c272da3d12365d987
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The PCI devices P2SB and PMC are hidden by the FSP and cannot be
unhidden, because the FSP locks their configuration. Thus, setting them
to `on` is not correct. Therefore, set their state to hidden.
Change-Id: Ib7c019cd7f389b2e487829e5550cc236ee5645b7
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48388
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SATA_AHCI is already the default mode for SKL/KBL based mainboards.
Therefore, remove its configuration from all related devicetrees.
Built clevo/n130wu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: Ib5222c1b0314365b634f8585e8a97e0054127fe9
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48378
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Skylake FSP isn't used by coreboot anymore. Therefore, drop the
misleading comment and the "KBLFSP" extension from the names of these
enums.
Also, drop the "MODE" extension to make their names shorter in general,
since it doesn't add any more value.
Built clevo/n130wu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: If37d40e4e1dfd11e9315039acde7cafee0ac60f0
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48377
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I56a905980e5ae382c3488b9fddb9fab382efc1d6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48375
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I193aea7c92f340bd80a41a3777bcddc3f1339620
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Remove unnecessary device declarations and remove comments where SMBIOS
slot descriptions are used.
Change-Id: I3aa3f72de764889becdb0afeb2dac522385d70ef
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48373
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use proper indents in the devicetree and align `end` keywords.
Change-Id: Id6e6f4ad648a9bed35305b7a446744c6ed06a150
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48372
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PCI devices P2SB and PMC are hidden by the FSP. So instead turning
them off, set their state to hidden being able to allocate ressources
for them.
Change-Id: Ie6e12f99b0a7ffb1c4831b3aa8705e911b677e88
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48371
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
remove TCC offset setting in overridetree.cb,
use default setting(# TCC of 90) in baseboard.
BUG=b:174547185
BRANCH=volteer
TEST=emerge-volteer coreboot
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Iaac1fae12ccaa8a623bc2dc3105262918523d440
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48264
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update lindar gpio settings for Synaptics trackpad no function issue.
Update I2C5 bus freq to 400kHz.
Improve Goodix Touchscreen power on sequence.
BUG=b:160013582
BRANCH=firmware-volteer-13521.B
TEST=emerge-volteer coreboot and check system dmesg and evtest can get
device. Verify trackpad function workable.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I8c1ab6bab1f9de187e2a78ead7b5bbaf758f5fcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Unique among the Volteer devices, the volteer2_ti50 variant connects to
the TPM via I2C. This CL introduces the proper devicestree declarations
for the Linux kernel to recognize that.
overridetree.cb is shared between "sub"-variants volteer2 and
volteer2_ti50, so both will have two TPM nodes, the I2C being disabled
by default. The odd _ti50 variant then has code in variant.c to enable
the I2C node and disable the SPI node.
BUG=b:173461736
TEST=abuild -t GOOGLE_VOLTEER2{_TI50,} -c max -x
Change-Id: I5576a595bbabc34c62b768f8b3439e35ff6bcf7b
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48223
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update Power Limit2 (PL2) minimum value to the same as maximum value for
volteer variants like baseboard, delbin, eldrid, terrador and todor.
All other variants uses the DTT entries from baseboard devicetree since
there is no override present for those variants. DTT does not throttle PL2,
so this minimum value change here does not impact any existing behavior on
the system.
BUG=None
BRANCH=volteer
TEST=Build and test on volteer system
Change-Id: I568e87c87ef517e96eaab3ff144b1674d26ae1e6
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
refer to cb:45878
Now that soc_get_pmc_mux_device() is gone, the PMC MUX connector devices
can be hooked up together via devicetree aliases.
BUG=b:174735512
BRANCH=volteer
TEST=build and type-c display work
Change-Id: I0bf84e2691856c9760d8fa9b6d853b04be10390a
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48268
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove the unused UART_BT_WAKE GPIO as BT is over USB.
Change-Id: I638b4528fa5c4c378a1e8ff7bb88546da1513df2
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Remove SOC_INTEL_COMMON_BLOCK_HDA from mainboards Kconfig since it is
selected by their SoC soc/intel/cannonlake.
Change-Id: I9597746a217575b42f6325998b948e16b452231a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48289
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move mainboard/gpio.h to variant/gpio.h and rename its methods to make
clear that these methods are implemented on variant level.
Change-Id: Ib4e7ec948ca4d019ad82ebc5abe39fc408281cf4
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48299
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add variant_configure_early_gpios() configuring early GPIOs to make the
difference clear.
Change-Id: I6e7c8c32963c9eeab4399947dac511442987cb45
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48298
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move mainboard/gpio.h to variant/gpio.h and rename its methods to make
clear that these methods are implemented on variant level.
Change-Id: Ibcb6322067285984bad70761fce34cfcb6ed8e0f
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48297
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move mainboard/gpio.h to variant/gpio.h and rename its methods to make
clear that these methods are implemented on variant level.
Change-Id: I1ae9b54ed683000f65323b11747ce3280a1c7f2a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48296
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allow to specify which signature is to be checked.
Change-Id: Ica874b1c4283fdb8dbd702c34ccb3315a2cf160d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Create the storo variant of the waddledee reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.3.1).
BUG=b:174284884
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_STORO
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I5ad41e0b2bc95b44733a2ad3c543267f3f56f9e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Without the EC blob being present in the SPI flash, the board won't even
power up.
Change-Id: Ia3c50e86414bbc707bc33e28c636196c1be2f1e6
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This is an adapted copy of mainboard/example/min86 that is currently
only used for Jenkins to test the SoC code in soc/amd/cezanne and isn't
expected to reach boot block at the moment. It will be extended in
future follow-up commits.
Change-Id: I6806955952fbfa3227294cfc44fdf9156140e933
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
1. Add VARIANT_HAS_MIPI_CAMERA to Kconfig.name
2. Add mipi_camera.asl
BUG=b:169356808,b:169551066
TEST=FW_NAME=voema emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I63d133246dbdc6aff7bf97d98f95052edf53bac9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47668
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DPTF paramerters form thermal team.
Set PL1 Min/Max 15/25W, PL2 Min/Max 40/49W.
BUG=b:174514010
BRANCH=puff
TEST=build image and verified by thermal team.
Change-Id: I9e6c4bae181e87f87f2e92337bb9d989f5b7d955
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
set APU_EDP_BL_DISABLE(GPIO_85) to low to avoid the VARY_BL fast than
APU_DP_BLON.
BUG=b:171954512
BRANCH=zork
TEST=validate the panel sequence with scope.
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Ia6d3f4335583bb2d91a6bce96d89cff84247d0ad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48203
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Create the copano variant of the volteer reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.3.1).
BUG=b:174413884
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_COPANO
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Ib06625f492f68a6a6f5c6b382772b68f1eb681ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
|
|
According to the spec provided by Bayhub, the 3.3V power rail must be enabled at least 100ms before reset is released.
To ensure this, set the power enable signal in the bootblock GPIO table.
BUG=b:173676531
BRANCH=firmware-volteer-13521.B
TEST=Built and booted into OS, test USB function normally.
Change-Id: I0c536f36c138ace93766f3024f6ec5d47b38269f
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47799
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use a new driver for the SX9324 proximity detector device.
This is first draft settings, will modify it after fine tuning.
BUG=b:172397658
BRANCH=zork
TEST=run "i2cdump -y -f 0 0x28" and checked all registers are expected.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I869d0b6640247099ca489e96ed94e03811a04bf4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47867
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Latest HW schematic add LTE_RST pin to control module power sequence.
BUG=b:173490220
BRANCH=zork
TEST=measure the waveform is meet the LTE module spec.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I0f0a35a905d711dd8d17dea2ae82a8dfa1fa05ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable Acoustic noise mitigation for drawcia and set slew rate to 1/4
which is calibrated value for the board. Other values like PreWake,
Rampup and RampDown are 0 by default.
BUG=b:162192346
BRANCH=dedede
TEST=Correct value is passed to UPD and Acoustic noise test passes.
Change-Id: Iadcf332d59dac2ba191b82742a18a1ab326940d1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48231
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Initiate device tree based on latest schematic.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia94119cb6d7eff6ea13c7d6a7dfd6ce891f706fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add implementation of EC smihandler
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I211f5755ff44514ab7ab4083f684ddd88c23fe48
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48115
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Perform EC initialization in bootblock and ramstages. Add associated
ACPI configuration.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ie1305706134ca7cc58b8a9941231d1ee14f80949
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable building for Chrome OS and add associated ACPI configuration.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I5311879a127a2c8da1bbb086449019d932d57b72
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Follow latest schematic UART_PCH_DBG is UART 0.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I8e334fee1adcd79d058b7ab07127f8ecf1735202
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48070
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable ACPI configuration and add DSDT ACPI table.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I08513ec159b69535f742a1fd70cdec9ec845d414
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Coachz rev1 has changed EN_PP3300_DX_EDP from gpio52 to gpio67.
BRANCH=none
BUG=b:174123578
TEST=emerge-strongbad coreboot chromeos-bootimage.
flash coreboot and boot up normally.
Signed-off-by: yuanliding <yuanliding@huaqin.corp-partner.google.com>
Change-Id: I32a721d0d725bf217debe35a5cdc01aa8f5d5daf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
To accommodate also `off`, two spaces are used after `on` to align
comments.
This unifies the devicetree files of the two variants.
Change-Id: I7908fe2313ddccb6a4448a6338d6cd4938264f62
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This reduces the difference with Cereme’s devicetree file.
Change-Id: I1e6ba5891245562d5132307eab224623031e11c8
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Since the FMD file isn't parsed any more by a shell script in the SoC's
Makefile.inc, we can use better human-readable numbers for the section
sizes.
TEST=Timeless build results in identical image.
Change-Id: I2117064a694f67767284f6fd4ac3604b254a2734
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
TEST=Timeless build results in identical image.
Change-Id: Ifa5c14add555b382f74ba1165131b1569bbef123
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48243
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This makes it possible to select both the legacy LAPIC AP init or the
newer parallel MP init.
Tested on i440fx with -smp 32.
Change-Id: I007b052ccd3c34648cd172344d55768232acfd88
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Qemu i440fx does not support an smihandler at the moment.
Change-Id: I5526b19b8294042a49e5bca61036e47db01fd28a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
All four SMI/NMI interrupt inputs have an external pull-up resistor and
get triggered by pulling the line low. Thus, correct the trigger to
active-low.
Also document the signals by adding appropriate comments.
The pads' connections have been determined by dissecting a dead board.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Id1a8c1e0b9fe723a15d04a88d565a53eeba9b085
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48093
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop the NMI overrides, since NMI now gets configured in gpio common
code. Also remove the variant init mechanism, which is unused now.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I02e0c679f9aafe33108320a8dfc62dcb278202ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48092
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is used as a signal to show the system state. It hadn't been used
up to this point as we're not currently using S0i3, but the fingerprint
sensor will use it to go into a low power mode, so set it appropriately
on Trembyle. Dalboz devices don't use the FPMCU, but set there as well
so that the state matches.
BUG=b:174695987
TEST=Verify GPIO state in S0 and S3 with the EC
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ibc725905909830d44f77c2498a26edf6d7a3dc05
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48255
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Vincent Palatin <vpalatin@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select MAINBOARD_USES_IFD_GBE_REGION to make CONFIG_HAVE_GBE_BIN
(Add gigabit ethernet configuration) selection available. Without that
onboard Ethernet won't work.
Signed-off-by: Ao Zhong <hacc1225@gmail.com>
Change-Id: I9fe138363fc47254285ebaa4a7dbe5b94a0a8784
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48007
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
IASL version 20180927 and greater, detects Unnecessary/redundant uses of
the Offset() operator within a Field Unit list.
It then sends a remark "^ Unnecessary/redundant use of Offset"
example:
OperationRegion (OPR1, SystemMemory, 0x100, 0x100)
Field (OPR1)
{
Offset (0), // Never needed
FLD1, 32,
Offset (4), // Redundant, offset is already 4 (bytes)
FLD2, 8,
Offset (64), // OK use of Offset.
FLD3, 16,
}
We will have those remarks:
dsdt.asl 14: Offset (0),
Remark 2158 - ^ Unnecessary/redundant use of Offset operator
dsdt.asl 16: Offset (4),
Remark 2158 - ^ Unnecessary/redundant use of Offset operator
Change-Id: I260a79ef77025b4befbccc21f5999f89d90c1154
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43283
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch reduces some code duplication in cbfstool by switching it to
use the CBFS data structure definitions in commonlib rather than its own
private copy. In addition, replace a few custom helpers related to hash
algorithms with the official vboot APIs of the same purpose.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I22eae1bcd76d85fff17749617cfe4f1de55603f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
|
|
Add stubbed out GPIO configuration and perform GPIO initialization
during bootblock and ramstage.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia658ab4b466242cf8658abb239f19a9c0a03849a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add entry point stubs of each stage for Brya. More functionalities will
be added later.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I44934c05ee32090b6e34648ee02f004c83e93d57
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48063
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia1ba8c997680c60ee1eabfae82459e127f664117
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48062
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch renames cbfs_boot_map_with_leak() and cbfs_boot_load_file()
to cbfs_map() and cbfs_load() respectively. This is supposed to be the
start of a new, better organized CBFS API where the most common
operations have the most simple and straight-forward names. Less
commonly used variants of these operations (e.g. cbfs_ro_load() or
cbfs_region_load()) can be introduced later. It seems unnecessary to
keep carrying around "boot" in the names of most CBFS APIs if the vast
majority of accesses go to the boot CBFS (instead, more unusual
operations should have longer names that describe how they diverge from
the common ones).
cbfs_map() is paired with a new cbfs_unmap() to allow callers to cleanly
reap mappings when desired. A few new cbfs_unmap() calls are added to
generic code where it makes sense, but it seems unnecessary to introduce
this everywhere in platform or architecture specific code where the boot
medium is known to be memory-mapped anyway. In fact, even for
non-memory-mapped platforms, sometimes leaking a mapping to the CBFS
cache is a much cleaner solution than jumping through hoops to provide
some other storage for some long-lived file object, and it shouldn't be
outright forbidden when it makes sense.
Additionally, remove the type arguments from these function signatures.
The goal is to eventually remove type arguments for lookup from the
whole CBFS API. Filenames already uniquely identify CBFS files. The type
field is just informational, and there should be APIs to allow callers
to check it when desired, but it's not clear what we gain from forcing
this as a parameter into every single CBFS access when the vast majority
of the time it provides no additional value and is just clutter.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib24325400815a9c3d25f66c61829a24a239bb88e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39304
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Mariusz Szafrański <mariuszx.szafranski@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch flips the default of CONFIG_NO_CBFS_MCACHE so the feature is
enabled by default. Some older chipsets with insufficient SRAM/CAR space
still have it explicitly disabled. All others get the new section added
to their memlayout... 8K seems like a sane default to start with.
Change-Id: I0abd1c813aece6e78fb883f292ce6c9319545c44
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
At least a part or the remaining definitions in the soc-specific smi.h
files are also common, but those have to be verified more closely.
Change-Id: I5a3858e793331a8d2ec262371fa22abac044fd4a
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Add the fw_config entries for the newly added boot device fields.
These are added as separate fields since a board may have more
than one selected.
BUG=b:173129299
TEST=abuild google/volteer
Change-Id: I2af9ffcf0b90d4f4b7f2f31613ee110d8f350454
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The initial commit only focused on GL9755S and RTS5261, but there
were recently other cards added to the fw_config and those also
need to be added to the probe lists.
BUG=b:173207454
TEST=abuild google/volteer
Change-Id: Ic27074a016ffbd4c4dd86104a6d85437357c4b82
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I928b4528fa5b4c378a2e8ff7bb88547da1413df2
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48213
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Default VBT supports only integrated Display port. Drawman supports a
HDMI port and hence support a separate VBT for Drawman.
BUG=b:161190931
BRANCH=dedede
TEST=Build and boot to OS in Drawlat and Drawman.
Cq-Depend: TBD
Change-Id: I8895cc67d87428eddb31328f1e3a90c346b54533
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
Add daughter-board ports bit field and mask in devicetree.
BUG=b:161190931
BRANCH=dedede
TEST=Build and boot to OS in drawlat & drawman.
Change-Id: Ibbd86fc8c3e44a7d1703b8ce75c48881226545c9
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
Add memory table to "mem_parts_used.txt", and command to generate files:
go build gen_part_id.go
./gen_part_id ../../../src/mainboard/google/zork/spd
../../../src/mainboard/google/zork/variants/shuboz/spd/
../../../src/mainboard/google/zork/variants/shuboz/spd/mem_parts_used.txt
Shuboz memory table as follow:
value Vendor Part number
0x00 MICRON MT40A512M16TB-062E:J
0x01 HYNIX H5AN8G6NCJR-XNC
0x02 MICRON MT40A1G16KD-062E:E
0x03 SAMSUNG K4AAG165WA-BCWE
BUG=b:174528384
BRANCH=zork
TEST=emerge-zork coreboot
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I5f5f875daab58343f1cc8a9327ea128ba5e1f050
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Config HID-I2C device to level trigger.
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:171546871
TEST=emerge-dedede coreboot
Change-Id: If8be25f591715765a99920b79482c862b1cc7079
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Current flash layout doesn't support the fsp debug builds since
the FW_MAIN_A/B doesn't have enough space to hold the fsp debug
binaries along with ME RW binaries.
This patch reduces the SI_ALL size to 3.5MiB and increase the
SI_BIOS to 12.5MiB to include both ME RW and FSP debug binaries.
BRANCH=dedede
TEST=Build and Boot jslrvp with fsp debug enabled coreboot.
Cq-Depend: chrome-internal:3425366
Change-Id: I6f6354b0c80791f626c09dabafe33eefccedb9c2
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48154
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
AGESA checks to make sure that the firmware version reading the MRC
cache is the same version that wrote it, so it doesn't need to be
erased during a firmware update.
BUG=b:173724014
TEST=Flash firmware to DUT, update firmware, check RW_MRC_CACHE was
not erased
BRANCH=Zork
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ice3d1d467c25366b7ef678cd6481d043f62644ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Use the system library for header files instead of relative filesystem
paths.
Built with BUILD_TIMELESS=1, coreboot.rom remains the same.
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: I0b356d0188f104d7c49571ce5c8fe65e79589123
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Built with BUILD_TIMELESS=1, coreboot.rom remains the same.
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: Id78c478a1252099cd1aa42c62efd406e7e1c5ef8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Update port connector information for Delta Lake.
Tested=Execute "dmidecode -t 8" to check all the information of
SMBIOS type 8 is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I880bb9a5a41077172423f78b56c19aadd93e001f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
As per latest schematics GPP_A15 is not used for EC_SYNC_IRQ
hence remove the unused GPIO.
Wrong GPIO configuration is causing platform reboot issue on
ADLRVP with Chrome SKU.
Change-Id: I704cd722683258c80197d8872d3bdaafb7c923dc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
1. Add 2 ports and 2 endpoints
2. Add support for OVTI5675
WFC Cam is on I2C5 and UFC is on I2C1
BUG=None
BRANCH=None
TEST=Build and Boot adlrvp board and able to capture image
using camera.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I6d2a4fdca99354d1b6977233c70ccd950c99d8a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47497
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure RST and PWR_EN signals for both WFC and UFC
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: Ie416da373756b1c73472b8572f87930965a3d6ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47496
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure I2C related GPIO as per ADL-P schematics.
This is based on Revision 0.974 of schematics.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I76e1207cb31bed10b6e9fbeb2456b6feec42f97e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
List of changes:
1. Enable Root Port 8 aka 0:0x1c:7
2. Assign free running clock for RP8
3. Apply W/A to get card detected on x1 slot
- Drive OEB 7:GPP_A7 and OEB 6:GPP_E5 low
TEST=Able to detect PCIe SD card over x1 slot
localhost ~ # dmesg | grep mmc
[ 3.643755] mmc0: SDHCI controller on PCI [0000:02:00.0] using ADMA
[ 3.825201] mmc0: new ultra high speed DDR50 SDHC card at address 17f8
[ 3.835452] mmcblk0: mmc0:17f8 SE16G 14.4 GiB
[ 3.849158] mmcblk0: p1
Change-Id: Ibea37b8de4dd020ff0108ec90ea6f8bcfaa4fb17
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48080
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
List of changes in SPD:
1. SPD Revision (of JEDEC spec)
2. SDRAM Maximum Cycle Time (tCKAVGmax) (MTB)
3. MSB -> CAS Latencies Supported, First Byte
4. CAS Latencies Supported, Second Byte
5. CAS Latencies Supported, Third Byte
6. LSB -> CAS Latencies Supported, Fourth Byte
7. Minimum CAS Latency Time (tAAmin)
8. Fine Offset for SDRAM Maximum Cycle Time (tCKAVGmax)
9. Fine Offset for SDRAM Minimum Cycle Time (tCKAVGmin)
10.Cyclical Redundancy Code (0- 125 byte)
TEST=Able to build and boot with updated SPD.
Change-Id: Iae7f2693e87bffb2dfa20bd07b22f4a4768c56cb
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
This patch adds LPDDR5 memory configuration parameters to FSP.
TEST=Able to pass FSP-M MRC training on LPDDR5 RVP.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I787bf97dd6c244bd3b0662e5bd061a2da80baa90
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
List of changes:
1. Initialize dq_map array in a single line
2. Make dqs_map array also in a single line
TEST=Able to build and boot ADLRVP LP4 SKU.
Change-Id: I64f2b38492934c8ede301f4b252c8700060ed4ac
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48077
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Get rid of variant_gpio_table() and configure GPIOs in gpio.c instead
of passing data around.
Change-Id: Ib158d6bdbcbceb3c1dc4f47fc7c3e098b9c7e5c4
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47974
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use include folder for header files allowing proper includes.
Change-Id: I80066fb925b918d040062397e633c5d499a50dbe
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47973
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Hook up the mainboard_ops driver and configure the GPIOs using .init,
since mainboard_silicon_init_params() is meant for the configuration of
the FSP, not the GPIOs.
Change-Id: I6ab8d258c6f81c90d835cb8d07c6387d3de76d85
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47850
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PICASSO_LPC_IOMUX was only used in the amd/mandolin board, but not in
the corresponding SoC code, so remove it from the SoC's Kconfig and
reanme it in the mainboard's Kconfig to MANDOLIN_LPC.
Change-Id: I261e093d6c56be6073a816b79c60d3a0457616f8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Create the drobit variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:171947885
BRANCH=none
TEST=emerge-volteer coreboot
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I63b7312bba236bd5af028359804d042f6850d8ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47787
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Updating Imon slope and offset values as per recommendation of
ODM based on calibaration.
Updating Imon slope to 1.0 and offset to 1.4
BUG=b:167294777
BRANCH=dedede
TEST=Boot dedede platform and confirm values in FSP.
Change-Id: I3eb32218040163f0abef9b8dd4c52efb16289fe7
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vinay Kumar <vinay.kumar@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Create the sasuke variant of the waddledoo reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.3.1).
BUG=b:172104731
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_SASUKE
Signed-off-by: Raymond Chung <raymondchung@ami.corp-partner.google.com>
Change-Id: I29405d63fd266224807e535c3f86a2ad5ab8cdf3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: SH Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Remove the devices unused or not present on this laptop.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I0decad499dfbb5f1e0a189d21f0fca47c80bd490
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47913
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The current I2C5 bus frequency is 367 kHZ, which does not meet the spec.
This change updates scl_lcnt, scl_hcnt, scl_hcnt value for I2C5 to bring
the bus frequency closer to 400kHz.
BUG=b:173670150
TEST=Verified that I2C5 frequency is between 386-387kHz.
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I6d60abe15645dc51ed9ee30975d2521b8940c2d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47736
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
