| Age | Commit message (Collapse) | Author |
|---|
|
* Add initial board commit based on HP8200 SFF.
* Add documentation.
* Serial and PCIe slot are working.
Tested on HP Z220.
Change-Id: I75987a7ea9a008a64281f0d5ab27e5148d36a4ec
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33207
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Because of some differences to the baseboard this board variant needs
its own GPIO table.
Change-Id: Ie3424cb0b867c5d43cd7db9e9ae654196cef5e90
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This automatically detects whether the southbridge supports AHCI.
If AHCI support is selected it will be used unless "sata_no_ahci" is
set in the devicetree to override the behavior.
Change-Id: I8d9f4e63ae8b2862c422938f3103c44e761bcda4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The RW_LEGACY section needs to be minimum 1M. For the 16MB BIOS
region, we had this region set too small, which was causing the
firmware_FMap FAFT test to fail.
BUG=b:133857135, b:129464811
BRANCH=None
TEST=test_that -b hatch <IP> firmware_FMap
Change-Id: Ie6311613ca3bb08e7f058a41d12f9a1153dc9c5e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Initial support for Facebook FBG-1701 system.
coreboot implementation based on Intel Strago mainboard.
Configure 'Onboard memory manufacturer' which must match HW.
BUG=N/A
TEST=booting SeaBIOS and Linux 4.15+ kernel on Facebook FBG-1701
Change-Id: I28ac78a630ee705b1e546031f024bfe7f952ab39
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Change-Id: I3d743e90444292be687999ab4f50aa89d514fbad
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33171
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some variants only support 4 PCIe ports so there is no need to have
those unavailable ports in the devicetree.
Change-Id: I154cae358fb7f862fc0c8eaa620474b37b5e6484
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30821
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:133389422
TEST=check SSD's power off sequence to meet PCIE requirement.
SSD's reset should be cleared before clearing SSD's power EN Pin.
Change-Id: Ia106b805deafb8a442b56bcce91b51135cb32988
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33182
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It's GPIO28 according to schematics.
Change-Id: I55be1ed178c818a17766e22cb2fd010412b8fe02
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enable LTR for NVMe and WiFi PCIe ports so that they can use ASPM L1.2
BUG=b:134195632
TEST=Verified L1 substate with lspci on hatch:
Before: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2- ASPM_L1.1+
After: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
Change-Id: I7fce60897b78dde12747ac7fb857c988d16118ab
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33161
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Setting up the SIO serial console is done in the bootblock.
Change-Id: Ideaf8f3dc0ee067e96d3fb5046071551c6d45329
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32985
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It is possible that cbfs_boot_map_with_leak() and malloc() could fail,
so detect those conditions and print error messages if they do.
Change-Id: I34951da0b73028c4c89446cb1779a72422997325
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1399147
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Xiang Wang <wxjstz@126.com>
|
|
This fallthrough is intentional (see commit 2257a35862 - Perform PL2
setting for syndra), so add a comment to make that explicit.
Change-Id: I57fe1e08f59aed12544cd2a71f1e0464f432f03b
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1397063
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This code to handle the brightness from SMM is copied from the Lenovo
Thinkpad X60 code, but does not work on later generation. The PCI
device it tries to address does not even exist on those devices.
Change-Id: Ia959eb5b747846048396e66d4c926c96c27f3878
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33138
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The code was already orphaned since its hook-up was removed
with a6be58fece (nb/intel/sandybridge: Remove the C native
graphic init).
Change-Id: Ia554c457e2f3a2dc42965ac5cded0be8e82311fb
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
All Baytrail boards have the same GPU PCI ID, so set it
here to avoid having to set it in each board's config.
Move the VGA_BIOS_FILE config from google/rambi into soc/baytrail
since it likewise applies to all Baytrail boards.
Change-Id: Id1e0580b55e3590d868cb839987f06c49bb07cf5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33026
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Buddy's WLAN ACPI code was equivalent to, but formatted
differently from the other auron variants. Since only
differnce is root port used, have buddy use common
WLAN ACPI and use preprocessor guards to set the root
port correctly.
Test: build/boot Buddy, verify Windows 10 boots
without ACPI BIOS ERROR.
Change-Id: I78d994f2bb3981d4d10cb534cd6e0ae673f73527
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30523
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable support for Gigadevice spi-nor flash.
Change-Id: I340eb3bf77b25fe3502d4b29ef4bf7c06b282c02
Signed-off-by: Nitheesh Sekar <nsekar@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ic282daf10dad42bc4513cc55f15ce80a4bd316a5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Signed-off-by: Prudhvi Yarlagadda <pyarlaga@codeaurora.org>
Signed-off-by: Nitheesh Sekar <nsekar@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Helios as a variant of Hatch.
BUG=b:133182138
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
attempts to build a Helios target.
Change-Id: I64ba06932eb0ee32405f7b14a94971a64c8fce71
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32918
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Created helios (hatch variant). Currenly copied from kohaku. Helios-
specific changes will come later.
BUG=b:133182138
BRANCH=none
TEST=none
Change-Id: I9d151621a1c42e6f3cadb288f7ea476828c059b5
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Create the Kindred variant of Hatch by taking a copy of the Hatch files
as placeholders. Kindred-specific changes will happen in future CLs.
BUG=b:133181366
BRANCH=NONE
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_KINDRED
Change-Id: I09ad3da0505d599fc3797d7fa24b4dc170dcd18b
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
These boards don't need a default FMAP. Moreover, having a default FMAP
disables automatic integration of optional regions like `CONSOLE`.
Also, these files contain an error: `COREBOOT` isn't placed at the top
of the image. Resulting in default builds without a reset vector ;)
Change-Id: If6331e19955034c02828e88902a5934c34d3e784
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33110
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
<types.h> is supposed to provide <stdint.h> and <stddef.h>.
So when <types.h> is included, <stdint.h> and/or <stddef.h> is removed.
Change-Id: I3b1a395cfe8b710fb6b468e68f4c92e063794568
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
This gets rid of the boilerplate back and forward calls between the
SOC/FSP-driver code and mainboard code.
Change-Id: I5d4a10d1da6b3ac5e65efd7f82607b56b80e08d4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32961
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Also adapt all users of these symbols
Change-Id: Ibf924a283d438de49a93ce661b0d9ca1a81cd6d1
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32956
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
When clapper was upstreamed, the devicetree was pulled from
the wrong firmware branch, leading to some incorrect settings
and touchpad, touchscreen, and audio not working.
Correct devicetree settings using Chromium branch firmware-clapper-5216.199.B
Test: build/boot google/clapper, verify touchpad/touchscreen/audio
functional under Linux (GalliumOS 3.0/kernel 4.16.18).
Change-Id: Iacfce575a054b1f484149f36d0aa83d20d034d8a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33025
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Legacy Google mainboards (pre-Skylake) shipped with the
SMBIOS manufacturer set to GOOGLE, which many Linux drivers
rely on for application of DMI quirks. Set it as the default
to avoid having to do so for each board's config
Change-Id: I61b0217f3535852d7d6e24a1ac78075c20c0825a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ib863e23863ba6d7504b6c4d32de2f1fea4e57fec
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The Gigabyte GA-B75M-D3H/D3V mainboard trees share a lot of duplicate
code, and can serve as a base for porting other Gigabyte 7 series
motherboards. Switch the Gigabyte GA-B75M-D3H/D3V mainboard trees to a
variant setup, defining ga-b75m-d3v as a variant of ga-b75m-d3h.
Signed-off-by: Alex James <theracermaster@gmail.com>
Change-Id: Ia175207a2568aefe1aa9bd8d4d990de6a26f1657
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Use the mainboard post code hook to inform the wilco EC driver of the
every stage.
BUG=b:124401932,b:133466714,b:133600566
BRANCH=sarien
TEST=Remove DIMM module, confirm diagnostic LED pattern for memory
failure (2 amber, 4 white).
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: Ic71e4a6e62b63ca2fd189957c4d6f49b61b934de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33047
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Even fingerprint device probe failed on non-fingerpint boards,the CRFP driver
still register the device that cause the GPE#1 as wake source every time.
Override devicetree for non-fingerpirnt variants to avoid unexpected wake
event(GPE#1).
BUG=b:129650040
BRANCH=firmware-nami-10775.108.B
TEST=Boots to OS and check no GPE#1 wake event from eventlog when S0ix exit.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I6fa96e04a34e296889414b96a8c604fc61b8a236
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33017
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to we turn off SSD power in S5. CB:32952
Based on M2 spec we have to turn on SSD power
before RST assert.
BUG=b:133389422
TEST=verify warm boot and cold boot are boot
successfully.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I5b78bab4be675bbb8795361bcfa5af52cb54bb1e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Turn off SSD power in S5.
BUG=b:133389422
TEST=measure H13 is low in S5
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I40b5381cac33b0eac962a7730ee5c57e60e6d375
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Modify reset delay to 20ms of touchscreen to address
i2c hid driver rebind failed issue after auto update of
touchscreen firmware
BUG=b:132211627
TEST=Touchscreen works after auto update and no re-bind
driver failed issue
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: If17afbd160a2c97beb69d0cb50e4a7dc654775f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Crews <ncrews@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
TODO in followup patch: Some not mainboard specific things should be
moved out of mainboard_smi_apmc.
Change-Id: Ifc2d8f7755ace598e66b162d071d472093e4656e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/26296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
This adds a file i82801gx/bootblock_gcc.c since other targets that
don't yet C_ENVIRONMENT_BOOTBLOCK still use the romcc compiled
bootblock.c.
Tested on Foxconn D41S.
Change-Id: I7e74838b0d5e9c192082084cfd9821996f0e4c50
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Unify thermal handling across Lenovo boards (except g505, which is
different). Namely, do the following:
* Move thermal levels from acpi_tables to thermal.h (and create if
necessary).
* Don't use board-specific ifdef guards.
* Set thermal levels using dedicated acpi_update_thermal_table function
as almost all Lenovo boards do.
* Update list of authors in comments. Merge all author's entries.
* Minor whitespace and formatting.
This makes diff -ruw between the Lenovo boards smaller.
Change-Id: If569f67c932b7fbf14893b890a5588df4994daeb
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29659
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are indeed two temperature sensors hooked up to the EC, but they
are indexed as 0 and 1, not 1 and 2.
BUG=b:132999028
TEST=Boot hatch with hardened EC, observe no more index overflows
Change-Id: Ia7f503bc1dc941635db52fce40f217bf34da6d2b
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Required for automatic onboard device detection in the next patch.
Change-Id: I3087de779faf8d006510c460b5372b22ae54b887
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32909
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Add VBT
* Configure OnBoard NIC
* Add documentation
Change-Id: Iad739b4e1dacb41f5f63247150951df7013bbf0c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Use the mainboard post code hook to inform the wilco EC driver of the
latest boot stage.
BUG=b:124401932
BRANCH=sarien
TEST=build coreboot for sarien and arcada platforms
TEST=Remove DIMM module, confirm diagnostic LED pattern for memory
failure (2 amber, 4 white).
Change-Id: If5bf69365d8be3bdbd433f305c85848206ded7b0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32937
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Works:
- bootblock, romstage, ramstage
- Serial console UART0, UART1
- SPI flash console
- iGPU init with libgfxinit
- LAN1, LAN2
- USB2, USB3
- HDMI, DisplayPort
- eMMC
- flashing with flashrom externally
WIP:
- Documentation
- VGA
For some reason Seabios can not find the CBFS region
and therefore it can't load seavgabios, but generally
it is working as soon as Linux is booted.
- ACPI
Works not:
- Devices needs proper configuration
- Seabios can't find CBFS region
Untested:
- GPIO pin header
- 60 pin EXHAT
- Camera interface
- MIPI-CSI2 2-lane (2MP)
- MIPI-CSI2 4-lane (8MP)
- SATA3
- USB3 OTG
- embedded DisplayPort
- M.2 slot
- mini PCIe
- flashing with flashrom internally using Linux
Change-Id: Ia913534ec176fc600fcd4ce3af335ebe682b0ed4
Signed-off-by: Felix Singer <felix.singer@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
This commit creates a garg variant for Octopus. The initial settings
override the baseboard was copied from variant bobba.
BUG=b:132668378
BRANCH=master
TEST=emerge-octopus coreboot
Change-Id: I9a36bc5dc3d2b891b1bce86015aa264894d1434b
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Currently, GPP_H0 gpio input rout is set to GPI_INT.
So, ACPI_GPIO_IRQ is required for GPP_H0 in devicetree
This change also aligns hatch's setting.
BUG=b:131742713
TEST=headset is working
Change-Id: Ie1264641bc4dfa5f98b6dab2d6f2133a6f9cbdb8
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ben Kao <ben.kao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Tested:
- Ethernet NIC
- Wifi RFKill
- USB
- LVDS, VGA with libgfxinit
- Booting with dock attached (COM1)
- Keyboard, trackpoint
- SeaBIOS 1.12
- S3 resume
- Tested in descriptor mode, with vendor FD and ME
- Add VBT to ACPI OPregion
Untested:
- SATA (likely works)
- Trackpad (my cable is broken, likely works)
- Displayport (likely works)
- Descriptorless mode
- DVD drive
- Extra battery
- model with ATI GPU
Does not work:
- Dock hotplug
- Quad core CPU (hangs during AP init, probably needs hardware mod)
- Hotplugging the expresscard slot (works with 'echo 1 | sudo tee
/sys/bus/pci/rescan')
TODO:
- proper dock support
- documentation
note: This board was hard to flash, I had to desolder the flash.
TESTED: on a R500 with an Intel iGPU, SeaBIOS 1.12, Debian 9,
Linux 4.9 from USB
Change-Id: I9e129b2e916acdf2b8534fa9d8d2cfc8f64f5815
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
All variants (t400, r400, t500, w500) use the same OPROM for the IGD.
Change-Id: I1b9db7b29b22809542f80f60a5e2eb3283fe1c02
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
sarien/arcada:
GPIO_COMM_0/2/3/4: Enable gpio community all PM configuration
GPIO_COMM_1: Disable RCOMP clock gating due to GPP_D18 IRQ mapped for H1 TPM.
hatch:
GPIO_COMM_0/1/2/3: Enable gpio community all PM configuration
GPIO_COMM_4: Disable RCOMP clock gating due to GPP_C21 IRQ mapped for H1 TPM.
BUG=b:130764684
TEST=H1 TPM interrupt working find and able to boot from fixed boot media
Change-Id: Ia4d5483847a4d243b9038119d4bb5990591cc754
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
GPIO_COMM_0/2/3/4: Enable gpio community all PM configuration.
GPIO_COMM_1: Disable RCOMP clock gating due to GPP_D16 IRQ mapped for H1 TPM.
BUG=b:130764684
TEST=H1 TPM interrupt working find and able to boot from fixed boot media
Change-Id: I1f83f938f201c6574367960b1027555767cf6f3d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Apply commit d7b88dcb (mb/google/x86-boards: Get rid of power button
device in coreboot) to AMD Brazos boards [1]:
> As per the ACPI specification, there are two types of power button
> devices:
> 1. Fixed hardware power button
> 2. Generic hardware power button
>
> Fixed hardware power button is added by the OSPM if POWER_BUTTON flag
> is not set in FADT by the BIOS. This device has its programming model
> in PM1x_EVT_BLK. All ACPI compliant OSes are expected to add this
> power button device by default if the power button FADT flag is not
> set.
>
> On the other hand, generic hardware power button can be used by
> platforms if fixed register space cannot be used for the power button
> device. In order to support this, power button device object with HID
> PNP0C0C is expected to be added to ACPI tables. Additionally,
> POWER_BUTTON flag should be set to indicate the presence of control
> method for power button.
[..]
> This change gets rid of the generic hardware power button from all
> google mainboards and relies completely on the fixed hardware power
> button.
The same problem exists with the AMD Hudson devices in coreboot.
For AMD Hudson (2) and Yangtze based devices this was removed in commit
44f2fab8 (AMD hudson and yangtze boards: Let mainboard declare power
button) [2].
Two devices are detected.
$ dmesg | grep Button
[ 0.209213] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.209254] ACPI: Power Button [PWRB]
[ 0.209332] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.209349] ACPI: Power Button [PWRF]
$ sudo evtest
No device specified, trying to scan all of /dev/input/event*
Available devices:
/dev/input/event0: Power Button
/dev/input/event1: Power Button
[..]
[1]: https://review.coreboot.org/5546
[2]: https://review.coreboot.org/27272
Change-Id: I0cbecb72f7e1bf3d051d3b7656c6af4d6f43b497
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/27496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The system should boot fine to OS on pressing power button before the
system enters G3. However, on hatch, we observe that the system waits
for few seconds at "Starting kernel" and then resets, with SD card tray
inserted and SD_CD# pad reset config set to DEEP. Hence configuring SD_CD#
pad reset config to PLTRST.
BUG=b:129933011
TEST=Built and verified on hatch.
Change-Id: Ic4466b96332f095ff39b28d98607e95fc3d12d6a
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
New emmc DLL values for Casta
BUG=b:122307918
TEST=Boot to OS on 12 systems
Change-Id: Ie51885fb9628fa093ecc38f4a3f3157f751ca9ab
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Set the system serial number from the VPD key "serial_number" and
the mainboard serial number from the VPD key "mlb_serial_number".
BUG=b:132970635
TEST=check serial number is set in SMBIOS based on VPD, and if there
is no VPD key found then it is empty.
Change-Id: Ia8f1486dcb1edc968b8eb1e6d989b10c05913aca
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
- Enable LPC TPM support in Kconfig and add pc80/tpm to devicetree
- Enable VBT support in Kconfig and add VBT files extracted from
vendor firmware
- Remove IGPU VBIOS entries from Kconfig
- Remove unused PS2 definitions in superio.asl
- Add PWRB ACPI device entry to mainboard.asl
- Remove duplicate chipset register initialization from mainboard.c
- Move ITE Super I/O configuration to mainboard_config_superio in
romstage.c
Signed-off-by: Alex James <theracermaster@gmail.com>
Change-Id: I2d11c55dc809b920bccf55f5f745d9f29b18bbb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
That's how we do it these days.
Change-Id: I6bf6460440d0f2e6973734ba8894a4be981d03c5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32812
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The FSP will lock down the configuration of GPP_A12, which
makes the configuration of the GPIO pin on warm reset not
work correctly.
This is only needed for the Arcada variant since it is the only variant
that uses ISH.
BRANCH=sarien
BUG=b:132719369
TEST=ISH_GP6 now works on warm resets on arcarda
Change-Id: Icb3bae2c48eee053189f1a878f5975c6afe51c71
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32831
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move the stoneyridge AcpiMmio code into soc/amd/common.
The SB800 southbridge introduced the MMIO hardware blocks at 0xfed80000
commonly known as AcpiMmio. Implementations beginning with Mullins
enable decode in PMx04. Older designs use PMx24 and allow for
configuring the base address. Future work may support the older version.
Comparing the documentation for AMD's RRGs and BKDGs, it is evident that
the block locations have not been reassigned across products. In some
cases, address locations are deprecated and new ones consumed, e.g. the
early GPIO blocks were simpler at offset 0x100 and the newer GPIO banks
are now at 0x1500, 0x1600, and 0x1700.
Note: Do not infer the definitions within the hardware blocks are
consistent across family/model products.
BUG=b:131682806
Change-Id: I083b6339cd29e72289e63c9331a815c46d71600d
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32649
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I73c557d6ef009fb2cac35fdea500dee76f525330
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This allows for serial console during the bootblock and enables
bootblock console by default.
Change-Id: I7746e4f819486d6142c96bc4c7480076fbfdfbde
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Previously broadwell used a romcc bootblock and starting verstage in
romstage was madatory but with C_ENVIRONMENT_BOOTBLOCK it is also
possible to have a separate verstage.
This selects using a separate verstage by default but still keeps the
option around to use verstage in romstage.
With a separate verstage the romstage becomes an RW stage.
The mrc.bin however is only added to the RO COREBOOT fmap region as it
requires to be run at a specific offset. This means that coreboot will
have to jump from a RW region to the RO region for that binary and
back to that RW region after that binary is done initializing the
memory.
Change-Id: I900233cadb3c76da329fb98f93917570e633365f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30384
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
IASL reports remarks 'Control Method should be made Serialized'.
Change-Id: I5606c6e435da17f7d4732148f6ddcedb1fde4ab0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Per Intel, the internal thermal protection is working better
than putting B0D4 _PSV in dptf.
BUG=b:131251533
TEST=Get ~10% better Octane score.
Correct TCC and TCC offset in MSR register.
Change-Id: If85afdc673687477ec85a47efcb264a7e5d6ae45
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
|
|
Add hynix_dimm_H9CCNNNCLGALAR-NVD for new onboard memory support.
BUG=b:130337306
BRANCH=firmware-rammus-11275.B
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure system boots up.
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: Ibd02953d0c6ac62fa4d7751fd8b103b74433aa73
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Also clean up cannonlake_memcfg_init.
The major changes include:
(1) Add enum 'mem_info_read_type' to spd_info.
(2) Add per-dimm-slot spd_info to cnl_mb_cfg.
(3) Setup memory config for each slot independently.
(4) Squash meminit_memcfg_spd().
BUG=chromium:960581, b:124990009
BRANCH=none
TEST=boot hatch, hatch_whl, and kohaku
Change-Id: I686a85996858204c20fd05ef24787a0487817c34
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32513
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds the SPDs for Samsung D-die 16Gbit and 32Gbit LPDDR3-2133
chips.
BUG=b:132206809
TEST=boots on atlas with C-die and D-die memory chips
localhost ~ # mosys memory spd print all
0 | LPDDR3 | SO-DIMM
1 | LPDDR3 | SO-DIMM
0 | 1-78: Samsung | 00000000 | K4EBE304ED-EGCG
1 | 1-78: Samsung | 00000000 | K4EBE304ED-EGCG
0 | 8192 | 2 | 64
1 | 8192 | 2 | 64
0 | LPDDR3-800, LPDDR3-1066, LPDDR3-1333, LPDDR3-1600, LPDDR3-1866, LPDDR3-2133
1 | LPDDR3-800, LPDDR3-1066, LPDDR3-1333, LPDDR3-1600, LPDDR3-1866, LPDDR3-2133
localhost ~ #
Change-Id: I8ba000aeeb77f07d7f18bda86b3c07f5b50478b8
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch adds a workaround for Samsung C-die 2G/4G memory chips.
For unknown reasons, some boards with Samsung LP3 memory chips
could not pass early CS/CMD training. MRC has to change the
granularity from 16 ticks to 8 ticks, which implies bad margin
with this memory chip. Another way is to enhance the drive
strength for CS. This patch is to enhance the drive strength for CS
and CMD. Enhancing the drive strength for CMD could gain margin abaout
3 more ticks. Root cause needs to be further investigated with memory
vendor.
BUG=b:131177542
BRANCH=None
TEST=USE=fw_debug emerge-atlas chromeos-mrc coreboot chromeos-bootimage
& check the MRC log to ensure correct Rcomp values are passed to
MRC. Tested with board ID #8 and #11.
Change-Id: I9ea3ceda8dc8bf781063d3c16c7c2d9b44e5ddd6
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
|
|
Call the raminit from a common location instead of from the mainboard
specific code.
Change-Id: I65d522237a0bb7b2c032536ede10e2cf93c134d8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32760
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To improve the bootflow, the scope of the pei_data needs to be
extended.
Change-Id: Ic6d91692a7bf9218b81da5bb36b5b26dabac454e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
This also links the gpio configuration instead of including it as a
header.
Change-Id: I9309d2b842495f6cff33fdab18aa139a82c1959c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Timestamps are initialized in cpu/intel/car/romstage.c.
Change-Id: Ia2b762667be17aa5b482cd585dd6f6198cf50d9e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32758
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move the onboard SPD to second channel as native raminit does and workaround
mrc expecations in northbridge code.
Required to move pei data to devicetree and to use the same code for mrc and
native raminit.
Tested on Lenovo T520:
Other fields then spd_data[0] are ignored.
Change-Id: If1910e82a4bd178c2a6c2991c91e09782122888e
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Update outdated comments.
Change-Id: I100f71345281a1dc52e99d2395f528d60a9a1f58
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32706
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The GPIO invert registers are already defined in the PCH code, so
just use the 8-bit versions of the registers instead of creating
a new GPIO field for the single bits.
This allows us to get rid of the Field(GPIO...) code that's causing
problems with IASL version 20190509.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Iac5dfb71b3a2b5a25c05a403cf5f403c7acecaaf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Error spotted using acpica version 20190509 (Change-Id: I6779a20).
Change-Id: Ic9cf16a7494667f6dab156c697fb8f8e9966051e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The gpio table is only used by depthcharge, and depthcharge rarely
has a need for the "recovery" gpio. On a few boards it does use the
gpio as a signal for confirming physical presence, so on that boards
we'll advertise the board as "presence".
All these strings probably should have been #defines to help avoid
typos (e.g., the "ec_in_rw" in stout seems questionable since everybody
else uses "EC in RW").
Cq-Depend: chromium:1580454
BUG=b:129471321
BRANCH=None
TEST=Local compile and flash (with corresponding changes to depthcharge)
to 2 systems, one with a "presence" gpio and another without. Confirmed
that both systems could enter dev mode.
Change-Id: Id6d62d9e48d3e6646cbc1277ea53f0ca95dd849e
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
A12 is not current set for ISH_GP6 so the ISH_LID_CL#_TAB
signal is not making it to the ISH properly. Enable the second native
function instead of the first.
BRANCH=none
BUG=b:131785573
TEST=gpioget on ISH now shows the correct gpio level
Change-Id: Ib3a654ae659037263aa9aa29d45b42ca67b7955b
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32738
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Id05fc39c0c0d0560e34e55f793060d29df82d026
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
CPU type is detected at runtime now.
Change-Id: I5e54176e235e43ca28e4baf43dbb9860e7fc3dbd
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
We keep the support, though. Just now that `libgfxinit` is fixed, we
don't need the distinction anymore. Causally, we also don't need
CPU_INTEL_MODEL_306AX any more.
TEST=Played tint on kontron/ktqm77. Score 606
Change-Id: Id1e33c77f44a66baacba375cbb2aeb71effb7b76
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The Kconfig MAINBOARD_FAMILY sets the family field of SMBIOS entry 1.
Match what vendor firmware does and use the same value as in the
version field.
Required for fwupd which uses the family field to generate a GUID.
Change-Id: I0033c42c5eac6b9d47d0acd16c67467b6d419534
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Leakage power is observed from TOUCH_SCREEN_PD# (GPP_E7 which is connected
to RESET pin of Wacom controller) during S5.
To avoid leakage power, GPP_E7 needs to be turned off before S5 entry.
BUG=b:129899315
TEST=Measure leakage power in S5 from both Arcada and Sarien
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie4229477b7149c0a75f4a8c6c7c453a37cc1c78c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add vbt files for nami variants and select Kconfig option
to utilize them. The default vbt is automatically added
by the Kconfig selection and so does not need to be
specified in the makefile with the others.
Test: boot vayne and akali nami variants, verify
display functional and correct vbt loaded.
Change-Id: Iaf49bdee7ae82a0a61192327351267f098eb5ab1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Set tcc offset value to 1 degree celsius for Arcada system.
BRANCH=None
BUG=b:122636962
TEST=Built and tested on Arcada system
Signed-off-by: Bonnie Lin <bonnie_ty_lin@wistron.corp-partner.google.com>
Change-Id: I3ca4be2f7b92e29fb133ecc32023526b177d2ac2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
According to Goodix GT7375P datasheet, reduce Goodix touch screen timing.
BUG=b:129727745
BRANCH=None
TEST=local build and tested with Goodix touch screen worked under
coldboot (10 times), warmboot (10 times), S3 (10 times).
Change-Id: I4bf081bab5e89d3ce336c6432da5ba71279fa98d
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
This change fixes the typo in CB:32161 (mb/google/hatch: Add Kohaku
board) that defaults GBB_HWID incorrectly for kohaku using
BOARD_GOOGLE_HATCH_WHL.
Change-Id: I387879619ac4f79fad422e5f1f047dfe3c7b5b22
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32690
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct Micron MT40A512M16TB-062E:J SPD CRC to 0x5330 to fix post hang
in AGESA TestPoint:05 TpProcMemSPDChecking.
BUG=b:127394249
BRANCH=master
TEST=emerge-grunt coreboot chromeos-bootimage
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Change-Id: I8fa49e6e938b3195945b3199438cc53f3e9c92e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Move optional EC PTS and WAK function into mainboard level.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie91a8168ae234f4fb4843c8587c77ae2f74aeb81
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Use CondRefOf to replace config optios for PTS/WAK acpi method dynamic
loading. Then we can move EC PTS and WAK method to be under mainboard.
BUG=N/A
TEST=Build sarien source code, check build/dsdt.dsl have EC.PTS method
included, build whlrvp soure, check build/dsdt.dsl don't have EC.PTS
method. Both able to build pass.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I9f4bd7240832caf070e65039e4ba2d8656371da8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32371
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update dptf for arcada DVT1.
BUG=b:123924662
TEST=Built and tested on arcada system
Signed-off-by: Mike Hsieh <mike_hsieh@wistron.corp-partner.google.com>
Change-Id: Ia8024a69547a569d288e02931190a98676eeaab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Disable unused PCI devices.
Reduces idle power by around 0.5Watt.
Tested on Lenovo T520.
Change-Id: I6990dc5810084261b75d2a327b6a103be44fd4cc
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
A subsequent patch will move the AcpiMmio support into amd/common.
Take this opportunity to rename the blocks in the 0xfed8xxxx region
with more consistency.
Change-Id: I9a69a6ecfc10f78b4860df05a77a061d2fc8be7d
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable VBOOT support on all devices that have a 8 MiB flash, using a
single RW_MAIN_A partition, allowing the use of tianocore payload in
both RW_MAIN_A and WP_RO.
* Add VBNV section to cmos.layout
* Add FMAP for VBOOT and regular boot
* Select Kconfigs for VBOOT
* Enable VBOOT_SLOTS_RW_A by default
Also build test VBOOT on Lenovo T420.
Tested on Lenovo T520 using Icb7b263ed86551cc53e1db7babccaca6b3ae2fe6.
Change-Id: Icb7b263ed86551cc53e1db7babccaca6b3ae2fe6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Mark all known PCIe root ports as ExpressCard slot.
Tested on Lenovo T520.
Change-Id: I43fb481512a54ee054c6fd0189053028fb3c3ec2
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32309
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fill SMBIOS type 9 fields for both sarien and arcada platform.
BUG=b:129485789
TEST=Boot up into OS and check with dmidecode -t 9 to we do have entry.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I47a697131b7aeeb64e0c4b4c0556842f1cb1b02e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Configure and enable GPIO for speaker amp max98357a.
BUG=b:117254418
TEST=Build pass and verified on kukui p1 board
BRANCH=None
Change-Id: I97655702dff402245326d2eff71fae0e336df9f5
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
`pei_data` was a struct with blob parameters from pre-FSP times.
Somehow, it sneaked into upstream FSP1.1 support (probably because
early board ports were written for a different blob). When added
upstream, its usage was already perverted. It was declared at SoC
level but mostly used to pass mainboard data from mainboard code
to itself and FSP data from FSP code to itself. Now that no board/
SoC code uses it anymore, we can finally drop it.
Change-Id: Ib0bc402703188539cf2254bdc395cca9dd32d863
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The SoC specific `struct pei_data` was filled with values that were
never consumed anywhere again. So just merge the used code into
`romstage.c` where it's effectively used.
Change-Id: I499b3cfcdd5400ea132749555d433a2d8a9471a3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The SoC specific `struct pei_data` was filled with values that were
later only consumed by the mainboard code again. Avoid jumping through
this hoop and fill FSP UPDs directly.
Change-Id: I040f4a55b4f4bad3f6072920e5e2eceded4cb9bb
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The SoC specific `struct pei_data` was filled with values that were
later only consumed by the mainboard code again. Avoid jumping through
this hoop and fill FSP UPDs directly.
The provided solution locates the SPD data in CBFS again to fill SMBIOS
tables. This is not perfect. OTOH, this code isn't mainboard specific
and doesn't belong here anyway.
Change-Id: Ib6103d5b9550846fe17c926631a013ff80b9598f
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32593
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
`chip.h` is usually used as devicetree interface.
Change-Id: Ied30927d68927b86758a84ccf3f5fbd8cce632f1
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32592
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
