| Age | Commit message (Collapse) | Author |
|---|
|
On rammus, system halt was observed because of gspi clk value being set to 0.
Log info from serial coreboot:
FMAP: area RW_NVRAM found @ 9fa000 (24576 bytes)
SF: Detected FAST_SPI Hardware Sequencer with sector size 0x1000, total 0x1000000
VBNV: Restore from flash failed
ASSERTION ERROR: file 'src/soc/intel/common/block/gspi/gspi.c', line 443
gspi.c
442
443 assert(gspi_clk_mhz != 0);
444 assert(ref_clk_mhz != 0);
445 return (DIV_ROUND_UP(ref_clk_mhz, gspi_clk_mhz) - 1) & SSCR0_SCR_MASK;
BUG=none
BRANCH=master
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure system boots up.
Change-Id: Ibe3937902901b2cdc1a196415c08fabb0f3155f2
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28405
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DMIC's are now connected to DMIC_CLK0/DMIC_DATA0.
So, enable the pins accordingly.
BUG=b:113744731,b:111106010
BRANCH=none
TEST='emerge-nocturne coreboot chromeos-bootimage' builds the image
Change-Id: I48cace3c6099a2853fcb377c695a5e325094baf6
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/28433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Nautilus-Wifi with m3 AP got a halt issue during CTS test.
Nautilus-Wifi was FCS with Celeron AP first and also its PCB/BOM was
validated only with Celeron. Since Celeron deos not support turbo
boost mode, its steady power demend and lower CPU frequency may not
reflect the potential noise hidden inside the board.
Bumping VCC_SA voltage offset 75mV confirmed works to mitigate the
potential noise coupling to VCC_GT/SA, and we verified this change
makes this issue go away on Nautilus-Wifi board.
Nautilus-LTE doesn't show this issue, since it has 10L PCB, will have
better grounding and less noise/ripple than 8L PCB.
BUG=b:111417632
BRANCH=poppy
TEST=Verified CTS test pass without an issue.
Change-Id: Id13fcc36a5b6ed42620c66f57a7303f30bff1a50
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/28439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change enables tablet mode ACPI device for all octopus boards.
BUG=b:113348027
Change-Id: I69a5dd41cd0958b93f8eed338fed4b6ee77a178f
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28466
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Set GPIO135 high to enable audio through the BCLK buffer.
BUG=b:113559558
TEST=None
BRANCH=grunt
Change-Id: I1dcecf5960d3c91e0c2165e7f8856ff423c06e8c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28482
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use ICH10's file instead of ICH7's.
Change-Id: I02678179e8f1dbd9b9f7d6407383a7a6cad15011
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/28450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add CMOS option that allows to use both integrated and discrete GPU.
Tested on ThinkPad W530.
Change-Id: I8842fef0fa1235eb91abf6b7e655ed4d8598adc7
Signed-off-by: Evgeny Zinoviev <me@ch1p.com>
Reviewed-on: https://review.coreboot.org/28393
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the mainboard.c in order to support the sku id in smbios
table where the sku id is queried from the eeprom via EC.
BUG=b:113714761
BRANCH=master
TEST=check the result of 'dmidecode'
Change-Id: I3413784cca1ac10a2468d84f2d06c0e1d701fdcb
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/28426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable dGPU power handling on Lenovo ThinkPad T430, T530 via PMH7
register 0x50.
Although there's no Thinker-1 chip on these models according to
schematics, dGPU power control via PMH7 works the same as on T420/T520,
so they can be considered Thinker-1-compatible.
It can be tested from linux userspace using util/pmh7tool.
To turn dGPU power off:
pmh7tool -c 0x50 7
pmh7tool -c 0x50 3
To turn it on:
pmh7tool -s 0x50 3
pmh7tool -s 0x50 7
To check whether it is on (bash):
reg=0x$(pmh7tool -r 0x50)
echo "$(( (( reg & 0x08 )) >> 3 ))"
or just `pmh7tool -b 0x50 3` with
https://review.coreboot.org/#/c/coreboot/+/28388/
Tested on ThinkPad W530.
Change-Id: Ieab1a33b3c680c757cc0999660b5cb7e122474cc
Signed-off-by: Evgeny Zinoviev <me@ch1p.com>
Reviewed-on: https://review.coreboot.org/28392
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the DRIVERS_SPI_ACPI to enable the tpm device node.
Without DRIVERS_SPI_ACPI, the kernel will popped out the below error:
cr50-update[592]: Starting cr50 update
cr50_get_name[595]: updater is /usr/sbin/gsctool -s
cr50-update[609]: exit status: 3
cr50-update[613]: output: Could not open TPM: No such file or directory
cr50_get_name[615]: board_id: '' board_flags: '0x', extension: 'prod'
cr50-update[617]: hashing /opt/google/cr50/firmware/cr50.bin.prod
cr50-update[678]: current state 3 in /var/cache/cr50.a3055efbc9.state
cr50-update[682]: not running
cr50-result[782]: Not running normal image. Skip setting Board ID
trunksd[795]: TPM: Error opening tpm0 file descriptor at /dev/tpm0: No such file or directory
BUG=none
BRANCH=master
TEST=/dev/tpm0 is created
Change-Id: I35287c6c54299c2677c41fc830675570b9d45a94
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/28400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable Synaptics touchpad device for liara
BUG=b:113309346
BRANCH=master
TEST=Verify touchpad on liara works with this change
Change-Id: Icdafe34a00fd55d5338fa07ffa304e48e7b85e7b
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch overhauls the Cheza FMAP, removing some sections we don't
seem to need (RW_CDT, the two RW_XBL_BUFFERs, and the second copy of
RW_DDR_TRAINING), and adding new sections we're going to need soon or
should have had anyway (RO_DDR_TRAINING, RO_FSG, RW_LEGACY).
Make more use of implicit offsets and sizes, because we can and because
it should make future adjustments easier.
Change-Id: I0bd9e59e9cfa162c478c4bd1f048fcac61ad5062
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/28403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: T Michael Turney <mturney@codeaurora.org>
|
|
After adjustment on Liara Proto
Audio: 399.2 KHz
H1: 398.3 KHz
TP: 399.0 KHz
BUG=b:113319200
BRANCH=master
TEST=emerge-grunt coreboot chromeos-bootimage
measure by scope
Change-Id: Ibba8c823ed8451a804cf731d49e7568a94ac7c6b
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Because of an incorrect transmit voltage swing, the signal must be
adjusted. The factor of slices for full swing level can be corrected via
the High Speed I/O Transmit Control Register 3.
Change-Id: I116802cd2a944658fc3022e948eba43cebe52bb4
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Alex Thiessen <alex.thiessen.de+coreboot@gmail.com>
|
|
Set threshold parameter for grip sensor STH9321
.ProxCtrl6: 75
.ProxCtrl7: 99
BUG=b:113303916
BRANCH=poppy
TEST=Built and verified parameter passed to driver
Change-Id: I8a410a23b5e3831fc8e90118b810fc2409a026eb
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/28381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Enrico Granata <egranata@chromium.org>
|
|
Also removed internal pull ups for CX_PREQ_L and
CX_PREQ_L signals as they have external pull ups.
BUG=b:110654510
TEST=On Yorp Proto 2, flashed image and verified that it boots to OS.
Checked Wake-on-Wifi works with both cnvi and pcie modules.
Also executed a few suspend resume cycles.
Change-Id: I0a76cd2a1481c828fc092aaf7e870a411624879c
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/28328
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Grunt takes a few seconds to update the EC, so display a notification
screen while that's happening.
BUG=b:113286040
TEST=Boot Grunt with old EC firmware, see update screen
Change-Id: I95fc4d3430bac66c09f57a4d34abde08752e5f0e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add weida touchscreen support
BUG=none
BRANCH=master
TEST=emerge-octopus coreboot, and verified that touchscreen works on
meep.
Change-Id: I4352322820237e4c2289410af6643e15109060a1
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Modify the previously SOC_CNL_LPDDR4_INIT to SOC_CNL_MEMCFG_INIT, to
make the infrasturture to handle both LPDDR4 and DDR4 cases in the
future. Consider the case of reading SPD from SMBus other than providing
SPD pointer directly.
BUG=N/A
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully.
Change-Id: I2f898147f67dd52b89cc3d9fc4e6b3854fa81f57
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28248
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set EC SPI bus config and init SPI bus according to the config.
BUG=b:80501386
BRANCH=none
TEST=EC is not working yet. This makes depthcharge go forward a little.
Change-Id: Id9209b6429417430cfcf7f5a5a1659e7e4bc7866
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/28251
Reviewed-by: Joel Kitching <kitching@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set up EC interrupt GPIO to boot depthcharge. Without this patch,
depthcharge will fail to detect EC interrupt GPIO.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui and see in logs, that depthcharge detects
EC interrupt GPIO.
Change-Id: I0ec2c70c189a059219954e0384aaf98995285728
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/28250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The firmware of devices connected to LPC should deassert the LPC CLKRUN#
signal when there is no bus activity on LPC.
Necessary changes:
- Enable LPC CLKRUN#
- Enable LPC PCE (Power Control Enable)
- Enable LPC CCE (Clock Control Enable)
- Remove I/O decoding range on LPC for COM 3
- Disable I/O UART driver
Change-Id: I2fd80e3fdcf23658f97b8182a77df7e09ddf25d6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Bayhub eMMC controller default runs SD base 50MHz at the first power on.
After boot into OS, mmc kernel driver will config controller to HS200/208MHz
and send MMC CMD21 (tuning block).
But Bayhub PCR register 0x3E4[22] (eMMC MODE select) is not clear
after system warm reset.
So eMMC will still run 208Mhz but there is no block tuning cmd in depthcharge.
It will cause two Sandisk eMMC (SDINBDA4-64G-V/SDINBDA4-32G-V) to fail to
load kernel and trap in 0x5B error (No bootable kernel found on disk).
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: Ic080682e67323577c7f0ba4ed08f8adafca620cc
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Reduce the CPU passive threshold sample rate from 5 seconds to 1
second so DPTF will react faster to rapid temperature increases.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BUG=b:113101335
BRANCH=atlas
TEST=manual performance/power testing on nocturne.
No longer see messages like below in syslog,
'CPU0: Package temperature above threshold'
Change-Id: I2dc9d157b54500bae29e123978bb8ad6e05ef619
Reviewed-on: https://review.coreboot.org/28325
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Reduce the CPU passive threshold sample rate from 5 seconds to 1
second so DPTF will react faster to rapid temperature increases.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BUG=b:67459049
BRANCH=nocturne
TEST=manual performance/power testing on nocturne.
No longer see messages like below in syslog,
'CPU3: Package temperature above threshold'
Change-Id: Ic20c718fd3a496db7c7192feec4f230d924cc458
Reviewed-on: https://review.coreboot.org/28324
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update TSR1 trip point from 48C to 50C.
Also, change power limit2 minimum value from 8W to 10W.
These are the values as per recent thermal tuning.
BUG=b:79779737
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: I33a9d2dc3e0e5566d95b1f1e46d3922dc8965b2b
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/28187
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit fixes the values and thus fixes the issue of
audio device not getting detected on random reboots.
Change-Id: I34a4f62815d192005c3324d4f71b0aba377fe738
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/28280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
|
|
Change-Id: Ie3ee4acfd272991133f02a56df6e23aa6071d3e9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Some unneeded includes are also removed.
Change-Id: Icd518c46d8503d11d24466c30840d7e514e9a05d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Most FADT report using ACPIv3 FADT table. Using the get revision
function keeps the table versions in sync.
Change-Id: Ie554faf1be65c7034dd0836f0029cdc79eae1aed
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28277
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch disables the unused PCI clock outputs on the XIO2001 PCI
Express to PCI Bridge.
Change-Id: I0b9cf51a713f4ab46e71d250397486d136c26177
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28284
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
add device "WCOM Digitizer" and "Synaptics Touchpad" for bobba
BUG=none
BRANCH=master
TEST=emerge-octopus coreboot
Change-Id: Ie0bf8ebab6d9cb9c8fe42a500efaa3d11ae359db
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28332
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
TEST: same sha256sum with BUILD_TIMELESS=1.
Change-Id: Icf3368bcf1351f0e7cd4041c3792d76362aec9e5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
To increase the lifetime of the circuit, it is necessary to reduce the
eMMC speed to DDR50 mode.
Change-Id: I40658b44a99e6600ed00950a1a177961f0055e7a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This enables CBAS device on Nocturne to allow hid-google-whisker driver
in kernel properly detect device configuration.
Change-Id: I5905a2de208e94062f2768a9b7d22147f85c7f38
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-on: https://review.coreboot.org/28262
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For the 1st redesign of mc_apl1 mainboard some adjustments are
necessary:
- The FPGA is now connected directly via a PCIe Root Port
- Internal Apollo Lake UARTs are now used
- Adjusting GPIO settings
Change-Id: I8917a52325306f24d1c39a88dac47b0cee760d57
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
A FPGA is not necessarily available in further mc_apl1 variants. So we
move the loading of the driver and the notify function to the mc_apl1
variant.
Setting the CPU to Max Non-Turbo Ratio is also not absolutely necessary
for further variants.
Change-Id: I9f8438407f231df08e1ad04655bb6f747257e268
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This supports the Foxconn d41s, d42s, d51s, d52s.
The following is tested (SeaBIOS 1.12 + Linux 4.9) and works:
- COM1
- S3 resume (with SeaBIOS needs sercon disabled)
- Native graphic init on VGA output
- SATA
- USB
- Ethernet
- PS2 keyboard
The base for this mainboard port was the Intel D510MO port.
Change-Id: Ie4ec9cbf70adcdddbc2e5d805e4806825c320072
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28227
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
src/mainboard/google/octopus/mainboard.c
Function dev_find_slot may return NULL,
check before its usage.
Found-by: klockwork
BRANCH=None
TEST=Built & booted Yorp board.
Change-Id: I160adbe3b0a5a2b0f11fd1567513860664d4bee3
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28235
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The change updates GPIO configuration for meep.
1. Update touchscreen power enable GPIO in devicetree.
2. Provide default override tables for GPIO configuration.
BUG=b:112955087
TEST=Boot on meep proto board with Intel (Jefferson Peak) wifi card.
Change-Id: Idb4e7a510eef15c2e118058d5848080782f4f665
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/28252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Since ifdfake has been deprecated in favor of better alternatives, such
as flashrom IFD parsing. Therefore, there is no need to support ifdfake
any further. Remove the IFD_*_REGION values on the few motherboards with
them.
Change-Id: Ie07116a7fb960c6ca832d802016f22c6677baac9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28232
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates the board id check for version >=2 to apply new
GPIO configs.
BUG=b:112618194
Change-Id: I3544c9596c465615818d2040682e554a64fc6b1a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28263
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This should not be board specific.
Change-Id: Ifa617e84af767f33a94f1ddfa7d4883c1a45198f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change PL1 from 4.5W to 7W, based on thermal test results.
BRANCH=eve
BUG=b:73133864
TEST=Verify the MSR PL1 limitation is set to 7W.
Change-Id: Ic3629f9c3b7eb6eef1a1b5a3051c9a11448bc9ad
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28078
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds support for controlling the keyboard backlight over ACPI.
BUG=b:112619894
BRANCH=none
TEST=verified keyboard backlight can be adjusted using keyboard
shortcuts
Change-Id: I25713f341e8b5a4e50903ac109bfa717f20969d8
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28205
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Enhanced Intel SpeedStep (EIST) on nocturne.
Change-Id: Ie9b832f5bc3a5ef300783bd9bcd7cf5d186b98fa
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable Enhanced Intel SpeedStep (EIST) on eve.
Change-Id: I49b18b817cda570f5c3c4d048c4e03329ac10b87
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch moves uart functions which are common across multiple soc to
block/uart. This will remove redundant code copy from soc
{skylake/apollolake/cannonlake}.
BUG=b:78109109
BRANCH=none
TEST=Build and boot on KBL/APL/CNL platform.
Change-Id: I109d0e5c942e499cb763bde47cb7d53dfbf5cef6
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This is meant to solve an issue where the proximity sensor may fluctuate
between CLOSE / FAR in rapid succession upon the user removing their hand
from the unit, before settling on the correct output.
Using the hardware debouncing filter solves this issue and removes the
spurious fluctuations.
BRANCH=None
BUG=None
TEST=manual on Nocturne, observing events come in
Change-Id: I78cc4852d42fcda6209fedce1ce91236b5814571
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/28112
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Weida touchscreen controller needs 130 ms delay after reset
BUG=b:111102092
BRANCH=master
TEST=Verify touchscreen on fleex works with this change
Change-Id: Ia86c3acf3c0e09ca05cc1681113672b546f830a0
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I4b0577bf3c00307733a1096749c1835d86764f29
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ib5799cceacefa89385a7615ef1c4b4d06157044f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Fix scope of ResourceSource, which should match the scope of the
device itself.
Change-Id: I9d0ff0ecc2721ec55b1ed12dddb495cd55966daf
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/28114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
All different memory configuration should be supported by now.
Thanks to Igor Lee.
Change-Id: Ib93c0e3cbdc29cbf6cff26292df4fbbb8208082f
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Igor Lee <getrun@gmail.com>
Reviewed-on: https://review.coreboot.org/27781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The romstage main() entry point on arm64 boards is usually in mainboard
code, but there are a handful of lines that are always needed in there
and not really mainboard specific (or chipset specific). We keep arguing
every once in a while that this isn't ideal, so rather than arguing any
longer let's just fix it. This patch moves the main() function into arch
code with callbacks that the platform can hook into. (This approach can
probably be expanded onto other architectures, so when that happens this
file should move into src/lib.)
Tested on Cheza and Kevin. I think the approach is straight-forward
enough that we can take this without testing every board. (Note that in
a few cases, this delays some platform-specific calls until after
console_init() and exception_init()... since these functions don't
really take that long, especially if there is no serial console
configured, I don't expect this to cause any issues.)
Change-Id: I7503acafebabed00dfeedb00b1354a26c536f0fe
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/28199
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After adjustment on Careena EVT
TP: 400.0 KHz
TS: 396.8 KHz
H1: 396.8 KHz
BUG=b:112663934,b:112664258
BRANCH=master
TEST=emerge-grunt coreboot
measure by scope
Change-Id: I9eeaf9290d95969a283f14618878e28faf0ea46f
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28119
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix the following failure from FWTS:
FAILED [LOW] AMLAsmASL_MSG_SERIALIZED_REQUIRED: Test 1, Assembler remark in line
131
Line | AML source
--------------------------------------------------------------------------------
00128| }
00129| }
00130| })
00131| Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
| ^
| Remark 2120: Control Method should be made Serialized (due to creation of named objects within)
00132| {
00133| Name (RBUF, ResourceTemplate ()
00134| {
================================================================================
ADVICE: (for Remark #2120, ASL_MSG_SERIALIZED_REQUIRED): A named object is
created inside a non-serialized method - this method should be serialized. It is
possible that one thread enters the method and blocks and then a second thread
also executes the method, ending up in two attempts to create the object and
causing a failure.
BUG=b:112476331
TEST= Run FWTS.
Change-Id: I6f4f6e7e94b01f673afc97d9415481ee63e406e3
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28122
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update SPD details to match with Coffeelake U RVP board
BUG=none
BRANCH=none
TEST=Boot on coffelake U rvp board and check if memory training is
passing and board boots till payload.
Change-Id: I953354cf5c6045731262f4f4e9da230187c2d246
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Update GPIO table as per board schematics.
GPIO table for other variants will be added later.
Change-Id: Ieb55d160ae2d6bff940840b1fba9411979332d4d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Nami doesn't support wakeup from hibernation by CR50. This causes the
device to remain turned off after CR50 update.
This patch disables turning off EC on cr50 update. CR50 resets the
whole system. So, EC reset is not required.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
BUG=b:112604277
BRANCH=none
TEST=gsctool -a -u /media/removable/cr50.bin && reboot
Verify EC reboots. AP prints 'Waiting for CR50 reset to pick up update'
then reboots.
Change-Id: I06f5eb6100e8af6ffec45d4de2b40eff44f89709
Reviewed-on: https://review.coreboot.org/28113
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These files are being updated to match the prevailing style
of cmos.default files.
Change-Id: I47d31d6fec8c9eb856aed0c63824d9556b7705e4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
change I2C irq to EDGE trigger
BUG=b:112616824
BRANCH=master
TEST=emerge-grunt coreboot
Raydium TS is working.
Change-Id: I86ec32bb3f2626e65d76c3259e3c4244a970e5de
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Used default console log level is 7 in src/console/Kconfig.
So let cmos.default use the same level as default.
Change-Id: Ia39ee457a8985142f6e7a674532995b11cb52198
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Side effect was observed that after override BayHub EMMC
driving strength to the max, EMMC CLK will be reduced to
51.x Mhz from 200 Mhz.
This will cause OS installation fail on Samsung EMMC sku.
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I848ab0cae474b15fbc4264c8ade63d5c6b4e489d
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This file contains two instances of "dptf_enable" = "1". This change
removes the 2nd instance (it doesn't have an explicit comment like the
1st instance).
The dptf devices still seem to be present even with this change, as
expected.
Change-Id: I890006644be9176ebaf555cc121c816e12f2b596
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The spec of the sx9310 says the I2C interface can handle standard
(100kb/s) and fast mode (400kb/s). The current setting is using fast
plus (1000kb/s) so this change is reducing the speed to fast mode.
I've been using the sensors with this change for a few weeks now, though
I also don't recall seeing an issue prior to this change.
Change-Id: I337fc02c52565d6ec4d7bac1b3564f65238962dc
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28075
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit 1fdb76945a9d06bbff37dee9da69e13a86c933f4.
Camera power is now handled by ACPI rules - no need to force the GPIOs
on by default.
BUG=b:80106316,b:111141128
Change-Id: Ifefec320884989f106a4b09c956d3a3279a1491a
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28072
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Ping-chung Chen <ping-chung.chen@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This defines new GPIO pin for controlling the display panel CABC
function. The default value is high (enabled).
BUG=b:112154569
Change-Id: I29083ab18e37f929a55b450b143463c67fe0abea
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28070
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This updates the DPTF sensor names to reflect the sensor locations on
the board.
BUG=b:75454415
TEST=verified new strings show up in
/sys/devices/LNXSYSTM:00/LNXSYBUS:00/INT3400:00/*/description
Change-Id: Ibffe6cb361de212ca03e75deaa8c454546d267a5
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28069
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ia38c6f8d978065090564d449cae11d54ddb96421
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch updates Power Limit (PL) for AML.
- PL1 as 5W TDP as POR
- PL2 as 18W TDP as POR
BUG=None
BRANCH=None
TEST=Build coreboot for Nocturne board and check default PL1/PL2 TDP.
cat /sys/class/powercap/intel-rapl/intel-rapl\:0/constraint_0_power
5000000 (5W TDP)
cat /sys/class/powercap/intel-rapl/intel-rapl\:0/constraint_1_power
18000000 (18W TDP)
Change-Id: Icb02a8a7c5fcd5e6aee45f14eba540a6b3ed3d67
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/27427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add TSR2 DART/DTRT package
BUG=b:110451144
BRANCH=nami
TEST=emerge-nami coreboot chromeos-bootimage
Test image with dptf.dv
Change-Id: I3328e17328415f5ebdcf84263e5456e11e55f769
Signed-off-by: T.H. Lin <t.h_lin@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This change updates GPIO configuration for bobba boards with id >= 1
This follows the same model as fleex:
a. Dynamically update touchscreen power enable GPIO in devicetree.
b. Provide default and bid0 tables for GPIO configuration in ramstage.
c. Configure WLAN enable GPIO differently in bootblock based on
boardid.
BUG=b:112354568
TEST=Built firmware for bobba
Change-Id: Id4ee4a1815e16ddfe60ed268688a8aaf4fb75579
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/28071
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Coffeelake U has 32MB flash chip support. Adding fmd file and enabling
CFL U board's Kconfig to output 32MB rom file.
Change-Id: I21431b7ac813781b12b95f80c6f8960a78caf4bc
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Add support for new board coffeelake RVP.
This patch is a copy patch and copies entire coffeelake_rvp folder from
cannonlake_rvp.
Changes done on top of copy:
1. Change copyright year from 2017 to 2018
2. Rename Cannonlake to Coffelake whenever applicable
3. Update entries in Kconfig and Kconfig.name
4. Rename variant directories to match coffeelake boards
Change-Id: Id37bfeb0ae51fd630fec96273216dbb2900782c7
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27904
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I189c981f3334836ab24bbc74491e9b58a2d403a4
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/27921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The paths defined in southbridge/intel/common/firmware/Kconfig should work just
fine.
Change-Id: Iaa780d9b3080416c6b1a7f24d97ecb8214962405
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28012
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All broadwell board set HAVE_IFD_BIN to default n, overloading the option in
soc, therefore just use the defaults in sb/intel/common/firmware.
Change-Id: I250dbbc9d61ecedc1a1eb48751ad966732604349
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28011
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is no need set the default HAVE_IFD_BIN explicitly to n.
Change-Id: I4a5fe45e7f8f6dd018937861b0fb92a8da49904e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28008
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is no need to redefine option present in
southbridge/intel/common/firmware/Kconfig.
Change-Id: I9999440031b07006e2df11e00dfb9f3dbe04f832
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28007
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix to accomodate for boards with more than 16 cores.
Change-Id: I35b61d94491c21ef76717f761e566ca815880f27
Signed-off-by: Samuel Jimenez <aerojsam@gmail.com>
Reviewed-on: https://review.coreboot.org/27847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I2c5edadfd035c9af08af9ee326a5a2dc8b840faa
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I3108193c0e0b644cecb74ae0c7a7b54e24a75b58
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I80dd65484fd52e9048635091fb20a123e959e999
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27869
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Current coreboot does not create ACPI device for OS to recognize Raydium
touchscreen.
List the touch screen in the devicetree so that the correct ACPI device
are created.
BUG=none
BRANCH=master
TEST=emerge-octopus coreboot
Change-Id: Ic61a69e19e97520da0702dfe6cb7496563fc34f4
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This was blindly copied from logs created under vendor BIOS in non-descriptor
mode which apparently set LAND in BUC.
Change-Id: I94c917600421ee742ece7f6f71309da80261da28
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Remove icc_max overrides to allow SoC code to set proper
icc_max based on CPU SKU.
BUG=b:78122599
BRANCH=none
TEST='emerge-nocturne coreboot chromeos-bootimage', flash to
nocturne, boot to kernel and verify device doesn't hang after
a few minutes.
Change-Id: I37c44e2428b802d754f2b12b8a57601d257e6582
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27996
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds a function to overwrite PL2 setting based on CPU
sku. From doc #594883, PL2 is 18W for AML-Y.
BUG=b:110890675
BRANCH=None
TEST=emerge-nocturne coreboot chromeos-bootimage & test with AML-Y
and KBL-Y skus.
Change-Id: Idfdc0c2434fdef56a7c25df05e640837a5096973
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27997
Reviewed-by: Caveh Jalali <caveh@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds a function to overwrite PL2 setting based on CPU
sku. From doc #594883, PL2 is 18W for AML-Y.
BUG=b:110890675
BRANCH=None
TEST=emerge-atlas coreboot chromeos-bootimage & test with AML-Y
and KBL-Y skus.
Change-Id: I468befcd2c4ad6c2bb9ae91b323a43f87ff65a26
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/27765
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow thermal table (b:112274477 comment#1) for first tunning.
BUG=b:112274477
TEST=Match the result from DPTF UI.
Change-Id: I63b2e50a4f6fc5453e6564e277600498ac0e6244
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Enable the GEO SAR feature for Octopus. Program wifi_sar VPD key.
coreboot reads the VPD and creates the ACPI table as per the WGDS spec.
BUG=b:112288077
TEST=Program VPD key, extract acpi table ssdt and valiate WGDS entry.
Change-Id: I40a6fd9e0ec8b440996bf3389322fd89bcca15a4
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
PERST signal is asserted/deasserted by ACPI routines during
suspend/resume. Configuring IOStandby for WLAN_PE_RST can result in
failure to resume from suspend state with wake-over-WLAN. This change
removes the IOStandby configuration for WLAN_PE_RST.
BUG=b:112371978
Change-Id: Ic7c0b2aa144233f8bbb4e5169d96347a1290abe1
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27994
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
When CNVi is being used, external wake using GPIO_119 is not
required. This change configures GPIO_119 as PAD_NC if CNVi is taken
out of reset.
BUG=b:112371978
Change-Id: Ifee90f428ed43c4d7c612c170476aff43b4a33ce
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change uses drivers/intel/wifi chip for CNVi device to ensure
that:
1. Correct device name shows up in ACPI node
2. It is possible to pass any parameters from devicetree to wifi
driver for SSDT generation.
BUG=b:112371978
Change-Id: Ia49820dd4f9cf2e0a9ef14931fbddd8a723208c0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change checks to see if CNVi module is out of reset:
1. If yes, then PCIe device for WiFi is disabled.
2. If no, then CNVi device is disabled.
BUG=b:112371978
Change-Id: I6e6cf2e646c897df017913056db87ac0cffa1a8e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27961
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
I2C2 is unused on all octopus variants. This change disables it in
devicetree.
BUG=b:112458032
Change-Id: I55abef864c06a448011f9570d3e6c0aa8bfdc5bc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28016
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates GPIO configuration for fleex boards with id >= 1
This follows the same model as phaser:
a. Dynamically update touchscreen power enable GPIO in devicetree.
b. Provide default and bid0 tables for GPIO configuration in ramstage.
c. Configure WLAN enable GPIO differently in bootblock based on
boardid.
d. Disable unused I2C devices in devicetree.
BUG=b:112458032
TEST=No errors observed on boot-up on fleex.
Change-Id: Ib4c449168b08e2393e2395d6b49469be5599c2ce
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The file `data.vbt` matches the VBT in the latest version of the vendor
firmware (version 3603). Tested with Linux 4.9 and everything works as
expected.
Change-Id: I8e3b1d274ac0df63989d966f477013e780611fa1
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/28050
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ib0839933f8b59f0c87cdda4e5374828bd6f1099f
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/23759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Allow for shared dram configuration by introducing a new table
that collapses the common settings after removing the part
numbers. When employing this scheme the part number comes
from CBI.
BUG=b:112203105
TEST=Placed part number in cbi. Faked out memory sku id. And enabled
DRAM part num always in cbi. Everything checked out.
Change-Id: I5229695ce3eb686421b89ac55d8df4b9fcec705c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/27991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
