| Age | Commit message (Collapse) | Author |
|---|
|
In particular:
- Enable regulators *after* configuring the voltage
- Allow 1 ms for the voltages to settle
- Enable clock after powering on regulators
- Remove extra delays between enabling things. The sensor requires 8192
clock cycles after the reset is lifted before I²C access, so 1 ms is
enough.
- Make the delay after lifting xshutdown 10 ms. This guarantees that
streaming will only start once the sensor has had enough time to settle
after lifting the reset.
BUG=chromium:959232
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Change-Id: I4589a7d7ec324f4520572a406cc11ad3feec8b21
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36723
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The PMIC opregion is used to change the direction of two GPIOs for I²C
daisy chain operation. Do this after the PMIC is powered on, not before.
BUG=chromium:959232
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Change-Id: I923987ef21a971df9e32ca03f2da4dccdac07843
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The pull direction is used to determine the initial state of the pin. If
no pull direction is specified, the pin will remain as input. Fix this.
BUG=chromium:959232
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Change-Id: I1158bc8aaa447b223e8ce25d808348e758de28c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36721
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modify DPTF parameters.
BUG=b:131272830
BRANCH=firmware-hatch-12672.B
TEST=emerge-hatch coreboot chromeos-bootimage
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I93930525edf4c5efb6b73bdfc8f16950754f7c9a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37272
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When migrating glados (and variants) to FSP 2.0, the older board-
specific VBTs were dropped in favor of the default FSP 2.0 VBT due to
compatibility issues. Now that libgfxinit is available and the default,
restore the board-specific VBTs so that external displays function
properly. Select MAINBOARD_NO_FSP_GOP for all variants except glados
since FSP/GOP init will not function properly with the older VBTs.
Test: build/boot chell and caroline variants w/libgfxinit, verify
external displays now work again.
Change-Id: If55a67e0d3d78e4acf80cee1733ad8e14b8847d4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add libgfxinit support for rammus. Use panel init values from VBT.
Test: build/boot rammus with libgfxinit and Tianocore payload
Change-Id: I4775a36d83bd67a0064a162effaf96649e9c186d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add VBT files for Atlas, Nocturne, Rammus, and Soraka variants.
Extracted from ChromeOS recovery images for the respective boards.
Select INTEL_GMA_HAVE_VBT for all variants except Poppy, since
it doesn't have a VBT (or a recovery image from which to extract one).
Change-Id: Icba2741e0b7309c22c027f956cd20cec78f34052
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch renames COMETLAKE_RVP to COMETLAKE_RVPU to avoid confusion.
TEST=build an image with COMETLAKE_RVPU
Change-Id: I93d7b5cc0be475926bb92503b66797dc67e607f5
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36793
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Can be restored with C environment bootblock.
Change-Id: I077d7bf088a0ffc65e9ec0d0b1c239194dc4f4ca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37347
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ie9e7a88f1f8dce967772e7c5ecf4aea971bb1c3f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37346
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allows boards to be transformed to C env bootblock one
at a time.
Change-Id: I1cc1910a8bfb6b3495593979cbf7194b0d82c8e1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37345
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add G2 GTCH7503 HID TS support
spec from G2: G7500 / Ver.1.2 (3, April, 2018)
BUG=b:141577276
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I91e4f2b934b64b14bca20108037b721288d40942
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37318
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Idd014f1ba85efff0c98a0c5ab60d775ac93cbc60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: Ia2e889fe72d746b71d92026e358c7471f56b381f
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ib720d9ca57cf1ce640f168cd6aab654b53e92b82
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37286
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Builds that would otherwise be reproducible are sometimes
broken due to added #include combined with __LINE__ used
in assert() statement.
Change-Id: If4a02393799a34bbae4f6e506052774526c1a969
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37266
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic92e08ae5b741889a8200d10ea8148e4b4384dc8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37270
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: David Guckian
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9e71474bea61befd61900aff554f32f1bc782a77
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Add ELAN EKTH6918 USI touchsreen support.
BUG=b:131205495 b:127996093
TEST=FW_NAME=kindred emerge-hatch coreboot chromeos-bootimage
and check touchscreen work.
Change-Id: I8b003685cd7ee68738bcd4298b63a44d6e6118e4
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37236
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Workaround to disable USB2 PHY power gating to fix issue seen when
Apple 87W USB-C charger is connected in S0ix state on WHL platforms
(based on Intel's recommendation). Issue is seen on CML platforms also.
So, disable power gating for Drallion too.
Add devicetree entry to set the flag to disable USB2 PHY power gating
for different CNL PCH based platforms
BUG=b:133775942
TEST=Connect Apple 87W USB-C charger when the system is in sleep and check if
the system wakes up after that
Signed-off-by: Surendranath Gurivireddy <surendranath.r.gurivireddy@intel.com>
Change-Id: I95909c73de758fccc7f616a330c1e1f0667e8c25
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36519
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested on Guado variant
Change-Id: Ie3a42d1d69d11eebda25e60572f5d9a7452144c2
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Tested on Zako variant
Change-Id: I433863b34731584797456eee6c2d270868a4f13f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Id9d9d804dfc2301b8d2186aff7be331d5ddbf18a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Idd7bfa4a97770f525c3f25f04f90c4bf092e4ae1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Both linear framebuffer and vga text mode verified
on chell and caroline variants
Change-Id: I106e7bb761055581634176a112816be8447e6745
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Drop all the sources that were guarded with this.
Change-Id: I6c6fd19875cb57f0caf42a1a94f59efed83bfe0d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/19275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
As per the 4.11 release requirement, CAR_GLOBAL_MIGRATION=n is a
mandatory feature, which most binaryPI boards lack as they
use BINARYPI_LEGACY_WRAPPER.
Disable all binaryPI platforms, except pcengines/apu2, from
the build for the time being. If a platform does not reach
POSTCAR_STAGE=y and C_ENVIRONMENT_BOOTBLOCK=y within a
reasonable timeframe both the mainboard and the respective
unused platform support code will get removed.
Change-Id: Id81ab0f168034187ecf62203b5a33ac6ba49a35d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Adopting the mainboard code to use hooks from state_machine.h.
No post codes are changed, except for those which were explicitly sent in
mainboard/romstage.c. Boot time is reduced by more than 7%, from 5.029s to
4.657s (coreboot timestamps, measured for loglevel 7).
POSTCAR_STAGE is required since coreboot 4.11 release.
TEST=boot PC Engines apu2 and launch Debian Linux with 4.14.50 kernel
Change-Id: Iff3dbe68ac17eb2947ff40b9769c6650255656cf
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
SuperIO header needs to be included regardless of
Kconfig option, otherwise compilation fails due to
missing prototype for try_enabling_LPC47N207_uart()
if DRIVERS_UART_8250IO is not set.
Change-Id: I0eda4aee2cbb114bde33e862940a64675469693d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Now that the EC software sync in romstage ("early EC sync") patches
have landed, it's time to enable this for Hatch.
BUG=none
BRANCH=hatch
TEST=verify EC sync runs in romstage
Change-Id: Ie567ab081b95b2302b051812fbf46e183c76bab6
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37025
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This feature and therefore the boards using it, will be deprecated
soon.
Change-Id: I1e970dd0613702346b5764d2b56012a72ed62cde
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37155
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some guarding is not needed because the linker drops the code,
other guarding is not needed because all platforms using the code now
have C_ENVIRONMENT_BOOTBLOCK.
Change-Id: I3b1a94e709aa291e1156c854874d7bf461981f32
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37157
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Meep was just the first one to fail, but the others aren't any better.
Change-Id: I177c50cfe7593a5b2ad770ce1ab1191d2dff93d2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37163
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Kconfig became stricter on what it accepts, so accomodate before
updating to a new release.
Change-Id: I92a9e9bf0d557a7532ba533cd7776c48f2488f91
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
According to SI team request, need to tune I2C bus 2 data
hold time more than 300ns
BUG=b:144736027
TEST=build firmware and measure I2C bus 2 data hold time
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: Idc58a595c77eba8544f27682a284be6aac5dbe25
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36945
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use correct address for second DIMM.
Tested on Lenovo T410:
* Both DIMMs are found and are usable
Change-Id: I8bace47f04a0e185c2901695879d4d4e12d4ce6a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37105
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Kohaku always used the default MEM_STRAPs in hatch baseboard. Adding
explicit configuration for Kohaku in the event that MEM_STRAP is set
differently in the baseboard gpio file.
BUG=b:144895517
BRANCH=hatch
TEST=None
./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I8f7105b3925f17c1741660d84c83c5d15f398a8d
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37106
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add VBT file extracted from vendor (AMI) firmware,
use by default to ensure functional display after
resume from S3 when using libgfxinit.
Test: build/boot Librem 13v2/3/4,15v3/4 boards, verify
functional display after resume from S3 when using libgfxinit.
Change-Id: I6bc5dab60e3601d56dae4300efee255d7c58329d
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37068
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7d20a850f8c2a1fcdee358c9e73d4c04eb3d7de8
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37006
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pull in all copies of smm_relocation_params structs defined
for intel platforms.
Pull in all the inlined MSR accessors to the header file.
Change-Id: I39c6cffee95433aea1a3c783b869eedfff094413
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Relocatable ramstage, postcar stage and C_ENVIRONMENT_BOOTBLOCK are
now mandatory features, which this platform lacks.
Change-Id: I3d9b6bb48bfd15c0182448f774e9af1e0c944fd5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Relocatable ramstage, postcar stage and C_ENVIRONMENT_BOOTBLOCK are
now mandatory features, which this platform lacks.
Change-Id: I08c21fd7e5cf8996911c3912bdbaf12d6450db42
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Relocatable ramstage, postcar stage and C_ENVIRONMENT_BOOTBLOCK are
now mandatory features, which this platform lacks.
Change-Id: Id38eada2d08426520261d4824990a49f8302976b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
These boards don't include any from sb/amd/sb800.
Change-Id: I2dbe39df6e4c5a86a0714b396bb89b03bbafd164
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36987
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Relocatable ramstage, postcar stage and C_ENVIRONMENT_BOOTBLOCK are
now mandatory features, which this platform lacks.
Change-Id: Ic00ca18de3d73a17041a3a2839307149ad7902b2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36961
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Relocatable ramstage, postcar stage and C_ENVIRONMENT_BOOTBLOCK are
now mandatory features, which this platform lacks.
Change-Id: Id6aa669542bcfd774fa5571d790f59f156a39a4b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add VBT file extracted from vendor (AMI) firmware,
use by default to ensure functional display after
resume from S3 when using libgfxinit.
Test: build/boot Librem 13v1/15v2 boards, verify
functional display after resume from S3 when using libgfxinit.
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Change-Id: I44d75486da3083cd1f07ea82dc18688db84a621e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36916
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO49 is strapped high, so setting it low likely increases power
usage. GPIO53 is hooked to a testpad so there is no reason to set
it here.
Change-Id: I00fb38c90417b673c2b36191c20279474eb0dc21
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Create new variant for jinlon
BUG=b:144150654
TEST=emerge-hatch coreboot chromeos-bootimage and boot on jinlon proto
board
Change-Id: I8deb29041475e38cbbf2f54519940f62b9f21822
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36681
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This also permits removal of vc/amd/agesa/f12, as it was the only
mainboard using it. That will in turn allow resolving some unique
Coverity issues reported against that source.
Change-Id: I73f570f01fcb5ba0e306508a569ea97f432596b3
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This board never really existed and nobody has any hardware left over
for it.
Change-Id: Icdba4f5209725995e4a55dcdbc299a9e91a5869a
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
By removing this code, we get approximately back to
where the board was before the fmap cache feature
was added, which is small enough for the Chromium OS
default configuration for the board to fit into the
32KB that the bootblock can use on the chipset again.
Change-Id: I52c0c30a14929913ded144bf086c12938e9c2699
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Some Sandy Bridge boards disabled the PCI-to-PCI bridge early to avoid
probing by the MRC. We can do that for all boards instead, based on the
devicetree setting.
Change-Id: Ie64774628fde77db2a379bdba6a921a31e52fa0d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The integrated GbE port is toggled via the Backed-Up Control (BUC)
register. We already disable it according to the devicetree setting
but never enabled it. This could lead to the confusing situation
that it was disabled before (different build, vendor BIOS, etc.)
but shouldn't be anymore.
As we need a full reset after enabling GbE, do it in early PCH init.
Change-Id: I9db3d1923684b938d2c9f5b369b0953570c7fc15
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This is supported by generic PCH code now.
Change-Id: Id5d764c97e47cdb08a68d03002ebebd996769914
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The BUC register is actually only 8 bits wide and setting bit 5
(disabling GbE) is already done by generic code.
Change-Id: I729a2a28f4b0d94eddd070dc89b7341ac0c35e4a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Don't overwrite the LPC decode config of the generic PCH code, move
UART init into bootblock_mainboard_early_init() and don't enable the
IOAPIC, which is already done by generic code.
Change-Id: I90d090f5bff29174e68981fea3c3f04c666b1d28
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36895
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The BUC register is actually only 8 bits wide and setting bit 5
(disabling GbE) is already done by generic code.
Change-Id: I4b8e14606c319e8bfc48d6757087f28af1bd5dfb
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Move UART initialization to bootblock_mainboard_early_init() and don't
override the generic LPC decode settings.
Change-Id: Icdab36ae0324175d3d51a050784b94a53d4b3b7c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The BUC register is actually 8 bits wide and shouldn't be bluntly
cleared.
Change-Id: I2ffd2d161005e839e730102b56af4f66efeb551e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Only set LPC decode bits that the generic PCH code doesn't set yet. And
don't enable the IOAPIC, which is already done by generic code.
Change-Id: I9d2f6a9ad3f5d83573e07596f2763edc75f4ee64
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This bit is already cleared by a reset.
Change-Id: Ib71496011c9621476a7327ba309f367c7fa971e4
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This bit is used to indicate xHCI routing across reboots. If anything,
coreboot should act on it, not set it during boot. ASL code would be
supposed to set it.
Change-Id: Id14647ac4e591cfa042ca8aad6dfc6ccda35c74a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The generic PCH code already enables a superset of LPC decoding. Move
UART setup to bootblock_mainboard_early_init() where it is expected.
Last but not least, remove an odd write to BUCs (RCBA+0x3414) and
beyond, as it's an 8-bit register and shouldn't be bluntly zeroed.
Change-Id: I24a4ccf6a529460a83f48522d2e05e6ad6614f81
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The generic PCH code already sets up a superset of these decodings.
Change-Id: I90bca37c46b89c35f323225fc3c087f1630397e4
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
mainboard_pch_lpc_setup() and mainboard_late_rcba_config() did 4
things here on top of the generic PCH code:
1. Enabling LPC decoding for gameports. It seems unlikely
that anything is using these ports and there is no code
to support gameports.
2. Decoding of COM3 instead of COM2. What COM?
3. Premature locking of ETR3/global reset. Bad idea.
4. Disabling the GbE port in BUC. Already done by PCH code.
Change-Id: Ie92dbf5c6813435995c4d24ed807ffc8d125953a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: Ia041b63201b2a4a2fe6ab11e3497c460f88061d1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
There is some overlap between romstage and bootblock.
LPC setup and BAR initialization is now done twice.
The rationale is that the romstage should not depend too
much on the bootblock, since it can reside in a RO fmap
region.
Enabling the console will be done in a followup patch.
Change-Id: I4d0ba29111a5df6f19033f5ce95adcc0d9adc1fd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This also changes the name to mainboard_pch_lpc_setup to better
reflect that it is an optional mainboard hook.
This adds an empty weakly linked default. The rationale behind this
change is that without an implementation of the hook some features
might not work but that the result is likely still able to boot, so it
can be made optional.
Change-Id: Ie8e6056b4c4aed3739d2d12b4224de36fe217189
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This also changes the name to mainboard_late_rcba_config to better
reflect what it does.
This adds an empty weakly linked default. The rationale behind this
change is that without an implementation of the hook some features
might not work but that the result is likely still able to boot, so it
can be made optional.
Change-Id: I1897d0f5ca7427d304a425f5256cd43c088ff936
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This adds an empty weakly linked default. The rationale behind this
change is that without the callback some features might not work
but that the result is likely still able to boot, so it can be made
optional.
Change-Id: I62c8010aa81fc45d208e9293feb2f45b45f34a82
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
RCBA32(V0CTL)= 0x80000001 already done inhere i945/early_init.c
Change-Id: Ia775f4e6158a217b48629d289845537e7ccf5e79
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Setting GPP_A10 to NC now that older boards are deprecated and this
GPIO is not in use anymore.
BUG=b:142056166
BRANCH=hatch
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: If8a249a3dcba90bb4ccb5e3f02595e680f789f93
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36869
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These mainboard don't feature a SPI flash. The SPI init code
will timeout on probing for a SPI flash which takes a lot of time.
Not including all SPI drivers also lightens the uncompressed ramstage
of about 17K or 7K compressed.
Change-Id: Icc7bf62d56fc2ef38854402e658830b8d59c737f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36870
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is some overlap between things done in bootblock
and romstage like setting BARs.
Change-Id: Icd1de34c3b5c0f36f2a5249116d1829ee3956f38
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36759
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic6ea158714998195614a63ee46a057f405de5616
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
This adds callbacks for mainboard specific init.
Change-Id: Ib67bc492a7b7f02f9b57a52fd6730e16501b436e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36787
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds 3 mb romstage callbacks:
- void mb_lpc_setup(void) to be used to set up the superio
- void mb_get_spd_map(u8 spd_map[4]) to get I2C addresses of SPDs
- (optional)mb_pre_raminit_setup(int s3_resume) to set up mainboard
specific things before the raminit.
Change-Id: Ic3b838856b3076ed05eeeea7c0656c2078462272
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36758
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add IFD and ME binary to generate complete SPI image.
BUG=N/A
TEST=Boot Embedded Linux 4.20 on Facebook FBG-1701
Change-Id: I9370bf9f2bba8887988bc6484524f6cf53bed8db
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34448
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a new Kukui follower 'kakadu'.
BUG=None
TEST=make # select kakadu
Change-Id: I9f25ce90285828c43435e45d9361ee7128d407fa
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36848
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add semtech SAR sensor.
BUG=b:143449140
BRANCH=octopus
TEST=Boot kernel with sx931x driver, i2cdetect show UU on slave address.
Change-Id: Icfb8acf1bac73973748aa7443c95147c60bad770
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36850
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIOs related to power sequnce are
GPIO_67 - EN_PP3300
GPIO_117 - FULL_CARD_POWER_ON_OFF
GPIO_161 - PLT_RST_LTE_L
1. Power on: GPIO_67 -> 0ms -> GPIO_117 -> 30ms -> GPIO_161
2. Power off: GPIO_161 -> 30ms -> GPIO_117 -> 100ms -> GPIO_67
3. Power reset:
- keep GPIO_67 and GPIO_117 high and
- pull down GPIO_161 for 30ms then release it.
BUG=b:144327240
BRANCH=octopus
TEST=build image and verify on the DUT with LTE DB.
Change-Id: I68b71425391eda1e92806fecdb9c8dcd54f0b95a
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36771
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove the logo.bmp file from the verify list when FSP1_1_DISPLAY_LOGO
is not set.
BUG=N/A
TEST=build
Change-Id: I87eac0b3cbe9450d5623b5331d8de096f140b595
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36853
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Changed the order of the verify lists and updated the comments to
reflect the order of execution. This makes the list easier to understand
and maintain.
BUG=N/A
TEST=tested on fbg1701
Change-Id: Ia656fbf07e5d42bafd328eaba69b660e5a1e4f1a
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36817
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change from hardcoded "fallback/*" to using CONFIG_CBFS_PREFIX.
BUG=N/A
TEST=tested on fbg1701
Change-Id: Ie728d01ebb93edd88516e91528ecaaa3f139b7a9
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
The public key should only be validated if the manifest is signed.
BUG=N/A
TEST=testedd on fbg1701
Change-Id: I703ed442e0b1926859f593ce9ca84133013224ea
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Removed unused include file.
BUG=N/A
TEST=build
Change-Id: I040b695a893b51de06f9658abdca8867727f053d
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36818
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
The postcar_verify_list should contain the items that should be verified
before the postcar stage is started.
BUG=N/A
TEST=build
Change-Id: I328858e4803873fed6d47313def5e7b9a434e8ad
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
The bootblock measurement was handled using the romstage_verify_list()
and the public_key in the mb_log_list. This is confusing as these are
both read-only items that should be handled in the same way.
Both will be handled in the romstage_verify_list().
BUG=N/A
TEST=tested on fbg1701
Change-Id: If05198deec85188f39a221a8b755798755afa5bb
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
vb2_context object is now stored on the workbuf as part of
vb2_shared_data. Use vboot's new API functions vb2api_init
and vb2api_relocate to create and move the workbuf.
BUG=b:124141368, chromium:994060
TEST=Build locally
BRANCH=none
Change-Id: I051be1e47bf79b15a1689d49a5d4c031e9363dfa
Signed-off-by: Joel Kitching <kitching@google.com>
Also-Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/1902339
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
Change-Id: I008fcca024fecf462c4b550b8dedbf4b06e491b8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36368
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I18948d31c0bf0bf9d641480a35fc710b9ee8ae84
Signed-off-by: Xiang Wang <merle@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Support to display a logo using FSP 1.1 currently resides in facebook fbg1701
mainboard.
The related support is moved to drivers/intel/fsp1_1 and used by the
Facebook fbg1701 mainboard. The storage for the uncompressed logo
is changed. We don't use .bss any longer as the logo doesn't need to be
available at runtime.
BUG=N/A
TEST=booting Facebook fbg1701
Change-Id: I276e6e14fc87d0b95fe5fdf7b617afd26769de79
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36679
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
One functional change is that southbridge GPIO init is moved
after console init.
Change-Id: I53e6f177aadcdaa8c45593e0a8098e8d3c400d27
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36757
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Setting southbridge GPIO is now done after console init,
which should be fine. This code is partially copied from
i82801ix.
Change-Id: I51dd30de4a82898b0f1d8c4308e8de4a00d1b7aa
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36756
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove some of the code duplication on i82801gx.
x4x boards are left untouched for now since that northbridge
also supports i82801jx.
The order of some things has changed:
- on i945 early_ich7_init is now done before the raminit
- enabling the IOAPIC is done before the raminit
Change-Id: Ie39549938891e17667a8819b49a78b9c71c8ec9e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36754
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Clean the vendor/manufacturing information in 16G_3200_4bg spd to
become generic spd.
BUG=None
TEST=emerge-hatch coreboot
Change-Id: I163dc4631a6b71efd36c75cfe1fc759040113387
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36810
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. ram id 8: 16G 2666 2 bank groups memory
2. ram id 9: 16G 3200 4 bank groups memory
BUG=b:142762387
TEST=boot with memory (KAAG165WA-BCT/H5ANAG6NCMR-XNC)
Change-Id: Ic63d911458b59de11c12ce776f6f7d04b1eb3b6c
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36667
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set GPP_C4 default to low to fix leakage voltage problem on touchscreen during power on.
BUG=b:142368161
BRANCH=Master
TEST=emerge-hatch coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure touchscreen works.
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: Ie9197192c9d6dfb30c10559990c6010b1b2d3a45
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36670
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Created helios_diskswap as a variant of helios (hatch variant).
BUG=b:143378037
BRANCH=None
TEST=none
Change-Id: I6536b3908ec569e1ac42ea7c5be85701012ab177
Signed-off-by: Alexis Savery <asavery@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
