| Age | Commit message (Collapse) | Author |
|---|
|
L520 and T420 should also use it - platforms are very similar to t420s
and t530. Z61t is based on T60/X60, X131e is based on X230 so commit
with Change-Id I13c08b8c6b1bf0f3deb25a464b26880d8469c005 should be
applied as well.
All four platforms are using ec/lenovo/h8 embedded controller.
Change-Id: Ib177f024871e82979dd430da86f1551aef14d446
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set up USB host controller.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: Iec98f3dc1bbf3dda3d28dbefad15339d48608c7e
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/28788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
There is no need to indent these lines with two tabs.
Change-Id: I2164f4e3ea48db8dc5242a55b0452782dae19a4b
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The assignment of header->checksum was in some cases done twice, or
unnecessarily split into two lines.
Change-Id: Ib0c0890d7589e6a24b11e9bda10e6969c7d73c56
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
While these pins were set to a pull-down 20KOhm, NPCX EC consumes
~2.1mW higher power. Becasue there was leakage current on both GPIO67
and GPIO70 from NPCX EC. With the external pull-up 10KOhm for
USB_OC0#/USB2_OC1#, this wasn't enough to prevent leakage current.
BUG=b:117139495
TEST=Check nxpc EC power to see power improvement
Change-Id: I685d876461c263f07ca4c8f8046635cb7087279c
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/29007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update CPU passive temperature threshold value from 70C to 80C,
to avoid early throttling for spiky workloads. Also, change CPU
throttling interval from 1 sec to 5 sec for CPU temperature.
BUG=b:116400298
BRANCH=None
TEST=Manual performance testing on nocturne.
Change-Id: Ic5031a4aa16f750237565f4e4928e78834b1d686
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/29044
Reviewed-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It always included if ACPI is supported since commit 822bc65 with
Change-Id I372dbd03101030c904dab153552a1291f3b63518 ("ACPI: Remove
CONFIG_GENERATE_ACPI_TABLES").
Change-Id: If17a6f43e368ccf850031b349714fa1ec4d02c1d
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/28954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Since there are two cameras on Nami and only one camera on Syndra.
We need to disable rear camera/DMIC on all Syndra sku.
BUG=b:112876867
Change-Id: I92fb43ec84387c268ffdb6d0d34a5e5b13bcf50a
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Tried to build all affected mainboards - still compiles fine.
Change-Id: I385cac1a75cee13453b831bd75b3ecc7a6d229fa
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This define is no longer used by anyone. It was removed everywhere else
with commit with Change-Id I556769e5e28b83e7465e3db689e26c8c0ab44757.
It seems that these two files were simply mislooked. So let's remove it.
Change-Id: Ifbb62441e16e97c0cae0713968844e296619a880
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This mainboard is quite similar to the p5qc. The main differences being a second
PEG slot, the IDE slot and being DDR2 only.
The following was tested:
- both PEG slots populated (coreboot sets legacy VGA decoding on the GPU in the
black slot)
- USB
- Ethernet NIC
- PS2 Keyboard
- COM1
- S3 resume
Change-Id: I49a4bca4256e2a905aff3252eca76387c81152c1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/29102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
A shortcoming of this driver is that if multiple devices with the same PCI ID
are present and don't have an eeprom, they would all get the same macadress set.
The r8168 driver deals with such cases so it should be easy to implement if
needed.
Change-Id: I5c32df00e25453c350a45e7f1ee6834b89c4289f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
SeaBIOS does not seem to like the Marvel IDE controller, so disabled SeaBIOS
support for ATA. It works fine in Linux afterwards.
Working:
- SATA on southbridge port
- SATA on marvel IDE controller ports (only in Linux)
- USB
- COM1
- PS2 Keyboard
- DDR2 DIMMs
- PCIe x16 PEG port
- PCI port
- NIC (needs a driver to set macaddress)
- S3 resume
Not working:
- SeaBIOS with ATA support (long timeout marvel controller so disabled)
- DDR3 fails because the proper clock signal does not get enabled. Even when
fixing this it fails later or during memtest, so it should be considered
unsupported for now
Untested:
- PCIe x1 ports (expected to work)
- sound (expected to work)
TODO:
add documentation
Change-Id: I4a81940707566776bd048904ca1387fea741fece
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28264
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
More platforms are not able to hibernate under certain circumstances,
such as when AC is plugged. This original path was conservatively put in
to prevent potential damage when cr50-update-caused asynchronous resets
occur. Julius' compelling argument that async resets from recovery mode
requests should have enough coverage of the design over the course of
project development. Remove the hibernate path and assume all is well
going forward.
Change-Id: I37121e75ff4e6abcb41d8534a1eccf0788ce2ea2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/29076
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4a9a9366c85206fa460519a26f48b3aada5bc7c3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/29100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Make the field names of the MISCx00 GPPClkCntrl more manageable by
shortening their names. Make the definitions look more like the
rest of the header file.
Change-Id: I515cd664808e38851a7dbdba899df4fb9bbbcde6
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
This change implements the callback to provide google_chromeec_event_info
structure in nocturne variant and sets MKBP SCI based on board id.
BUG=b:112366846,b:112112483,b:112111610
Change-Id: Ifcc10aefc8f450214bd64dfffaf8854ada43f323
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change adds a variant callback to read google_chromeec_event_info
from variant at runtime to allow override of any events based on
factors like board id.
This callback is used in ramstage and smm to get
google_chromeec_event_info structure for performing various actions
like setting masks and logging wake events from EC.
BUG=b:112366846,b:112112483,b:112111610
Change-Id: If89e904c92372530a0f555952f87702f068e0b03
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
STAPM devicetree registers do not indicate the unit, which causes confusion.
More importantly, the time was assumed to be in seconds when it's actually
milliseconds. This caused early STAPM configurations to fail.
BUG=b:117590953
TEST=Build grunt
Change-Id: I2a7e3d43601992d1f7b02456913c763d940fe9ee
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29035
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With correct stapm values audio issue is not observed with
PsPPBalanceLow (Gen1 speed).
BUG=b:117569918
TEST=audio playback multiple times
Change-Id: Iaeae52b262b12622a6753432e3fc40bf5f0fd8e0
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/29028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
stapm_time passed to smu via agesa is in msec. With earlier value
smu was getting stapm_time as 2.5 sec instead of 2500 sec and thus
causing issue in S3, and audio in PsppBalanceLow state.
BUG=b:117569918, b:117252463
TEST=
1.) audio works with PsppBalanceLow
2.) S3 cycles
Change-Id: I673e7e673d042918dff47141f37bbca354f5c45c
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/29027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Tune I2C params for I2C buses 0, 5, 6, and 7 to ensure that the
frequency does not exceed 400KHz.
BUG=b:117298114
TEST=emerge-octopus coreboot chromeos-bootimage and measured frequency
under 400 KHz
Change-Id: Id608aae7edf54a24f364606dd7952521d1d67c1a
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/29021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Only two UARTs are connected to the FTDI UART USB chip.
Change-Id: Id5ae7266ce44c9f64c7f7aeaf23c49122041f47a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Need to tune I2C bus 0 clock frequency under the 400KHz
since this bus attached the Stylus EMR pen and need meet the spec.
Bug=b:117297214
TEST=flash coreboot to the DUT and measure I2C bus 0 clock
frequency whether under 400KHz
Change-Id: I06d9d25f52d7f641d937de0d6b7df3d7a076fbf9
Signed-off-by: Peichao.Wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28973
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now only those UARTs that are enabled in devicetree.cb are initialized.
Tested on Opencellular Elgon.
Change-Id: I145c224148f0cc078bb1c76f588f603e73121a62
Signed-off-by: Jens Drenhaus <jens.drenhaus@9elements.com>
Reviewed-on: https://review.coreboot.org/28975
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Add SPD file for sdp samsung_dimm_K4AAG165WB-MCRC (ram id: 9)
BUG=b:112679174
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: Iac1e3ca4b009cc9be94608cd342f535fa581a5eb
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28974
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the new I2C slave reset function and reset all slaves connected to all
4 I2C. Do this in all boards.
BUG=b:114479395
TEST=Added debug code. Build and boot grunt. Examined output, confirmed
GPIO pins changing as required. Removed debug code.
Change-Id: Ia78ee5d5319d3c1a7daa9c56c81d435999b3a359
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28575
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:117173908
TEST=Build delan
Change-Id: If149b8c43ff16637c38d5320eb606bb72d62e953
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Clean up Kconfig file in order to support variants for fizz. Add
BOARD_GOOGLE_BASEBOARD_FIZZ that can be set by various fizz variants
to use the common baseboard configs.
BUG=b:117066935
BRANCH=Fizz
TEST=emerge-fizz coreboot
Change-Id: I9c89f1dc526a9d623e1ae4d4b52a923489b389d3
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
After adjustment on Liara EVT
H1: 392.03 KHz
TP: 397.87 KHz
TS: 397.71 KHz
BUG=b:116309237
BRANCH=master
TEST=emerge-grunt coreboot chromeos-bootimage
measure by scope
Change-Id: Ib5d7ce09ac58f33ee826d7541e1a0d14a03add9a
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Setting default PSPP setting to BalancedLow was causing audio
playback issue in most of the units. With BalancedLow either there
was no sound or noise on playback.
Switching to BalancedHigh as default option.
BUG=b:116553085, b:112020107
TEST=Test playback and hear proper audio.
Change-Id: Ibf64d7b8e58e60ce931ddc85f11b135708cdb1ee
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/28967
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Its spreading copies got out of sync. And as it is not a standard header
but used in commonlib code, it belongs into commonlib. While we are at
it, always include it via GCC's `-include` switch.
Some Windows and BSD quirk handling went into the util copies. We always
guard from redefinitions now to prevent further issues.
Change-Id: I850414e6db1d799dce71ff2dc044e6a000ad2552
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable DRAM_PART_NUM_IN_CBI feature to get DRAM part number from CBI
and set DRAM_PART_IN_CBI_BOARD_ID_MIN to 3 for DVT.
BUG=b:115697578
TEST=verified it in Bobba EVT board which rework ram id.
Change-Id: I0fb457d8772f5038e5d90188d7682956ddfad46b
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28891
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Wifi wake register is incorrectly set in devicetree.
Set wifi wake to its correct wake source, GPE0_DW2_01.
BUG=b:117330593
TEST='emerge-nocturne coreboot chromeos-bootimage', flash nocture,
connect wifi to a hotspot, suspend device, echo freeze >
/sys/power/state, and then shutdown the hotspot and verify device
wakes.
Change-Id: Iafa865ca79d33541d7f47b69d2fb209e7f9c98af
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28938
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The WAKE# signal has moved to LAN_WAKE, so WAKE# is now
floating and must be disabled. This change disables WAKE#.
BUG=b:117284700
TEST=none
Change-Id: I1c25e4ba28cd2b8807cd155d47c29c0d3ee9e8a5
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
RISC-V is not a project of the University of California, Berkeley,
anymore; it stands on its own feet now.
Remove the "UCB" component from the RISC-V mainboards in the "emulation"
directory, and don't set MAINBOARD_VENDOR to UCB, either.
Change-Id: I301d9d0091a714e62375052e5af06a9197876688
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In order to make the macro name consistent for all PAD_CFG1_IOSSTATE_*
macros, this change uses lower case x for *RXD*. It helps avoid
confusion when using the macros.
Change-Id: I6b1ce259ed184bcf8224dff334fcf0a0289f1788
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28924
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All ampton boards should have the DRAM info configured in CBI and so
DRAM_PART_NUM_ALWAYS_IN_CBI is already selected for ampton. This
change gets rid of the redundant minimum board id value for Ampton.
BUG=b:117071184
Change-Id: I59f60b8c5aa34b55b8e473c06cc49ea7ae284d62
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Fleex does not have any device on I2C0 and hence this change disables
I2C0 device (16.0) in devicetree and gets rid of the I2C tuning
parameters for I2C0.
BUG=b:115600671
Change-Id: Ib799eae05b667cee2272bbd37f0ca44b7cec66cd
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
I2C3 is connected to the debug header and won't be required unless
connecting the debugger. This change disables I2C3 device (16.3) in
devicetree.
Change-Id: I650fa040075119a21864c83d8470dd2155c9edb9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
|
|
This change uses the generic device driver to provide DMIC properties
in ACPI table to the OS driver.
BUG=b:112888584
Change-Id: I239f571bc29f02793f017a4713b5af03b23cfa3e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28797
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: HARSHAPRIYA N <harshapriya.n@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Config option SOC_INTEL_COMMON_BLOCK_HDA is currently used for
initialization of HDA codecs only. This prevents adding of any static
devices under the HDA device node. However, there can be boards which
want to add devices under HDA node (e.g. nocturne that wants to
provide DMIC properties to OS) without performing any codec
initialization using the HDA. This change:
1. Adds a new config option SOC_INTEL_COMMON_BLOCK_HDA_VERB that can
be set explicitly by the boards that want to perform codec
initialization.
2. Uses newly added config option is used to guard the initialization
functions for the codec. Rest of the device operations can still be
used by all the other boards without having to use HDA codec
initialization.
3. Selects the newly added option SOC_INTEL_COMMON_BLOCK_HDA_VERB in
kblrvp which is the only board enabling HDA codec initialization
using common block code.
4. Selects original config SOC_INTEL_COMMON_BLOCK_HDA for skylake SoC.
Above changes need to be bundled and pushed in as a single change in
order to avoid breaking existing users.
BUG=b:112888584
Change-Id: Ie6f39c13a801833b283120a2d4b6f6175688999c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Need to tune I2C bus 0/6/7 clock frequency under the 400KHz for
digitizer, touchpad, and touchscreen.
Bug=b:117126484
TEST=flash coreboot to the DUT and measure I2C bus 0/6/7 clock
frequency whether can <400KHz
Change-Id: Icb9592c688b864a21efd4963a4463845dfaa06fb
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28907
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Nautilus-LTE sku shows abnormal reset symptom at high temperature chamber
test, but the root cause is unclear.
Experimentally, setting SlowSlewRate IA/GT/SA to 1/2 improves this abnormal
reset issue, so we would apply it until find root cause of this issue.
BUG=b:117130599
BRANCH=poppy
TEST=Built and passed on reliability test with modified coreboot
Change-Id: I7fa0041989113097e3b283dbcf4ca2a73629fe54
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/28785
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds the ACPI controls for power sequencing the touchscreen.
The initial setting is to keep the touchscreen powered off and in
reset. When linux is ready to talk to the touchscreen, it powers it
on and releases reset via ACPI.
BUG=b:110286344
TEST=verified touchscreen is functional in chromeos
Change-Id: I58c42a8f09342cfe54f82ef0e6cd8ea72a5140dc
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28869
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Setting the stapm parameters is causing S3 resume failures and
performance issues. Removing these settings until more testing is
done and the issues are solved.
BUG=b:117252463, b:116870267
TEST=boot grunt
Change-Id: I2299ab81fcc2af0529bfac3be562b05116c64a49
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
In CBFS layout:
oem.bin size is 10 bytes.
In cbfs_boot_load_file, buffer size will need to be larger
than decompressed_size, otherwise CBFS data can not be
extracted into buffer.
Then we need to check buffer whether it's empty string separately.
BUG=b:79874904
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I4f1bbb690ecca515ac920f5058ee19b5bfd8fa5e
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Move the FSP param initialization function to a separate file,
as being done on the SoC side and remove the empty romstage.c file.
Change-Id: Ibe64bc4ebfdbbb124bcd460dc419da1f469aa7fa
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/28662
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
GPP_C19 is not being set as the code is incorrectly setting
GPP_C16 instead, causing SAR sensor not to work, so this change
sets GPP_C19 to NF1.
GPP_E3 is not being initialized in the code. Initialize GPP_E3
to a no connect as documented in the board schematic.
BUG=b:117124878
TEST: 'emerge-coreboot chromeos-bootimage', flash nocturne and
verify that i2c transactions work for the left SAR sensor.
Change-Id: I9e972dbe4214cdd15d80d63dfa058e7755f7ecbb
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28867
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Increase the reset delay for the touchscreen to 10 ms.
BUG=b:116857433
TEST='emerge-nocturne coreboot chromeos-bootimage', flash and boot
nocturne to kernel, log in and execute the following two commands:
echo "i2c-WCOM50C1:00" > /sys/bus/i2c/drivers/i2c_hid/unbind
echo "i2c-WCOM50C1:00" > /sys/bus/i2c/drivers/i2c_hid/bind
and verify the bind command does not echo back a
"-bash: echo: write error: No such device" error.
Change-Id: I102b57ea5a10d22bee6d4f7c6f114b380a5d586b
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28803
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Caveh Jalali <caveh@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch modifies "oem_table_id" from "RAMMUSMAX" to "RAMMUS"
so that the audio topology file can be loaded properly by the
operating system.
BUG=b:112945714
BRANCH=master
TEST=There is no error message like "failed to load topology firmware" in
kernel v4.4 log.
Change-Id: I66a38ea38791dd3d9606a05b7b696236c350237f
Signed-off-by: Marx Wang <marx.wang@intel.com>
Reviewed-on: https://review.coreboot.org/28870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable DRAM_PART_NUM_IN_CBI feature to get DRAM part number from CBI
and set DRAM_PART_IN_CBI_BOARD_ID_MIN to 2 for DVT.
BUG=b:116721822
TEST=Verified it in Fleex EVT board which rework ram id.
Change-Id: I0f191c950aa6a70069bffa1f1802386ab263a310
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use GPIO GPP_D17 pin as the EC sync interrupt and provide this value
to the embedded controller to be exported to the OS.
This interface was tested on a reworked Nocturne board with modified
EC and a modified kernel driver to ensure that the interrupt asserts
as expected and can be used by the kernel driver.
Change-Id: Ie2b33692367b5d9ecc2b128180d8cfe4f6b347b1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/28759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In order to enable the OS SPI driver to use the software interface of
this controller the OPCODE menu has to be set up properly before
locking the controller. This is done on baseboard level so that all
variants will get this done as well.
Change-Id: I0bf0619ff0610c00325f03d13b6794aee8a62504
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/28834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
After adjustment on Careena
Audio: 402.805 kHz -> 396.8 kHz
TP: 406.1 kHz -> 399.5 kHz
BUG=b:110984023
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: Ia3eb91ca3772d5f122498e3989ec03838fce06a5
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable the IOMMU device on all kahlee based mainboards.
BUG=b:116196614
TEST=Check dmesg for AMD-Vi messages.
Change-Id: I18b9ba1a970c6973226e736d72f82fd53010f31c
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/28754
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Need to tune I2C bus 6 clock frequency under the 400K Hz
Bug=b:115600671
TEST=flash coreboot to the DUT and measure I2C bus 6 clock
frequency whether arrive to 398.07K Hz
Change-Id: I5cc1f67f0db0553cb8424f81408ed4686cddb2fb
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The FCH ASL is now capable of controlling the D-states of most AOAC
devices, as well as properly reinitializing the xHCI firmware on a
resume. Call the FPTS and FWAK methods.
BUG=b:77602074
TEST=On Grunt, go to S3 and wake with a USB keyboard
Change-Id: I4df8523569dc3dfbd87f79e780c18d39f0d9a37f
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28773
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to minimize Electromagnetic Interference (EMI) on the LVDS
interface driven by PTN3460, clock spreading must be activated for
mc_apl1 mainboard. The modulation ratio is set to 1 % of the nominal
frequency.
Change-Id: Ie457fcdbb6239dc0b25e2c35ad7a310ee80383f9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28761
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested on Elgon EVT board and boots into GNU/Linux.
TODO:
* Add hard reset function for VBOOT.
* Add EC code
* Add SPI flash write protection
Change-Id: I9b809306cc48facbade5dc63846c4532b397e0b5
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/28024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Vendor VBT on ThinkPad R500 intends to set a 220MHz backlight PWM frequency
which seems to work well.
Change-Id: Ic1a12c7e3173468561ed5615319962d0abc6d61b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Linking this file instead of including a header makes it possible to easily
change gpio settings for a variant.
Change-Id: Ifd496510d4868f5901a9dbbf7f1523ccffaf15ab
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28628
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some settings like direction are only used if the mode is GPIO.
Change-Id: I4efc54dfef3721b528b90d49f490014d9132cdf8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28627
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This board is pretty much like the G41M-GS, but with DDR3 memory
instead. The PCB layout is almost identical.
What works:
- S3/S4 resume
- RAM init
- Booting to Debian
- Display lights up w/ libgfxinit
- Both PS/2 work
- Ethernet
- Graphics card on PEG
- USB
- SATA ports
- NVRAM debug_level
- Internal flashing
- PCI slots (tested with CT4810 audio card)
- fancontrol (Only CPU fan can be regulated)
- Audio (Rear ports only)
What does not work:
- Hell knows what might be wrong
What is not tested:
- PCIe x1
- IDE
- Floppy
- Parallel port
Change-Id: I66b216af740680c390ea82e4fe07737c20227cc6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enable Gigabit Ethernet network controller on whiskey lake rvp platform,
add NVM bin file as well.
BUG=N/A
TEST=Build and boot up into chromeos on whiskey lake rvp platform, and
check eth0 can get IP address assigned,
Change-Id: Ia299a2aa78108175074e084cc34a7d2b38cf1c72
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27848
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We refer to Intel Doc#594883.
The recommended Ac/Dc loadline values are as below:
# VR Settings Configuration for 4 Domains
#+----------------+-------+-------+-------+-------+
#| Domain/Setting | SA | IA | GTUS | GTS |
#+----------------+-------+-------+-------+-------+
#| Psi1Threshold | 20A | 20A | 20A | 20A |
#| Psi2Threshold | 2A | 2A | 2A | 2A |
#| Psi3Threshold | 1A | 1A | 1A | 1A |
#| Psi3Enable | 1 | 1 | 1 | 1 |
#| Psi4Enable | 1 | 1 | 1 | 1 |
#| ImonSlope | 0 | 0 | 0 | 0 |
#| ImonOffset | 0 | 0 | 0 | 0 |
#| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V |
#| AcLoadline | 14.4 | 4.2 | 5.7 | 4.47 |
#| DcLoadline | 14.0 | 4.17 | 4.2 | 4.3 |
#+----------------+-------+-------+-------+-------+
BUG=b:112167318
BRANCH=master
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure system boots up.
Change-Id: I2d83d835ec841ac4cc811a0a69f74d203d5ea173
Signed-off-by: statham_chu <statham_chu@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Some of the FSP silicon UPD entry can be updated base on device switch
in pci device tree, have both static config setting and device tree "on"
and "off" will be redundant.
BUG=N/A
TEST=Build and boot up fine with Whiskey Lake RVP platform.
Change-Id: Ia36cfab03c4613786e5580a039d89007b630adf9
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27766
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per internal discussion, there's no "ChromiumOS Authors" that's
meaningful outside the Chromium OS project, so change everything to the
contemporary "Google LLC."
While at it, also ensure consistency in the LLC variants (exactly one
trailing period).
"Google Inc" does not need to be touched, so leave them alone.
Change-Id: Ia0780e31cdab879d2aaef62a2f0403e3db0a4ac8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
|
|
This mainboard is based on mc_apl1. In a first step, it contains a copy
of mc_apl1 directory with minimum changes. Special adaptations for
mc_apl2 mainboard will follow in separate commits.
Change-Id: I0af60ab0dfe556dd95da2cf1a49c685a8f0ae4eb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28735
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
In preparation for a future MC Apollo Lake board which will be equipped
with LPDDR4 modules, it is necessary to make the swizzle data
configurable. Starting from the mc_apl1 baseboard, which is equipped
with DDR3L memory and therefore does not need swizzle data, the
structures are initialized with zero.
Change-Id: I4954d0a00d1d5fc28a8dda45a9fb27f98d5c3f1e
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28730
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Increase power limit1 maximum value from 5W to 7W. This value as per
recent measurement on closed system which shows better performance
results.
BUG=None
TEST=Build and tested on Nocturne system. Performance tests
show better results.
Change-Id: I7485b1d2afde46ec28d548c13be35a43e7572918
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/28686
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add tdp_pl1_override value as 7W.
BUG=None
BRANCH=None
TEST=Build coreboot for Nocturne board
Change-Id: I16d3894da68bc3be6eff526062f9a88ef2df60c7
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/28708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Puthikorn Voravootivat <puthik@chromium.org>
|
|
The previous does not work well enough when testing with
high ambient temperature. Update DPTF settings to make
it work better.
List of tweaks:
1. Raise DRAM Critical temperature from 48C to 55C
Note that there are mechanisms in EC that complement
this because of DPTF limitation that we can't have
multiple passive temperatures.
2. Lower response time for DRAM temp sensor from 60s to 5s.
3. Increase throttle priority to the charger when DRAM hit
passive temperature from 100 to 200.
BUG=b:112550414
BRANCH=None
TEST=Manually tested by thermal team.
Change-Id: Idf7efa76b2c6085cf97aa9f65c6ce066e8cff99a
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-on: https://review.coreboot.org/28738
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Cheza board contains a couple of non-standard FMAP sections that
contain per-board calibration data. When flashing new firmware to the
board, care should be taken to copy these sections over so that all
features can still function correctly afterwards. This patch wraps a new
RO_PRESERVE FMAP section around these sections to make them easier to
preserve as a group.
Change-Id: I77919336f609a1be399598736f46921c3da99e68
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/28728
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Configuration of pins exposed by superIO are inconsistent between board
variants. Each platform should have UARTs enabled, this is expected
behaviour of these pins. Given that APU2_PINMUX_UART_x can be set for
all boards as default.
Change-Id: Ifb7dfe23a95ba0e572adc38212333d9fdd234d53
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/28720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This board doesn't support the newest RISC-V Privileged Architecture
spec (1.10), and it's based on an FPGA so it's a moving target.
Now that there's actual RISC-V silicon out there (from SiFive),
mb/lowrisc/nexys4ddr will only continue to bitrot.
Change-Id: I4e3e715106a1a94381a563dc4a56781c35883c2d
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28706
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Apu2 boards use Infineon SLB9665 TT 2.0 module which is TPM2.0.
Remove TPM1 option to allow choice between TPM1 and TPM2.
SLB9665 TT 2.0 detection fixed in change 21983.
Change-Id: Ie9788c43d8b32b2f6329a072b88c962c34eca119
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/28000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Need to tune I2C bus 6 clock frequency under the 400KHz
Bug=b:116543001
TEST=flash coreboot to the DUT and measure I2C bus 6 clock
frequency whether arrive to 399.1KHz
Change-Id: I95b535a6b429fc34961a4953004a1c51e53a9be6
Signed-off-by: Peichao.Wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28747
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit aef592d9b66aa18d83b0a211ead26013ff1f7d98.
Reason for revert: Use values from driver instead of hardcoding in
firmware (b:113303916)
Change-Id: I02d21803f38da227f1d85b00cb6b5274d81dbbb4
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/28690
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Enrico Granata <egranata@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since I2C bus 7 attached the touchscreen device however Phaser units
that haven't it. So for avoiding side effects, we need close I2C bus
7 SCL and SDA respectively.
BUG=none
TEST=according to sku_id (Phaser: 0x1, Phaser360: 0x2, Phaser360s: 0x3)
distinguish whether close these gpios.
Change-Id: I8ad17761f2a053dc329bbec0a0a3284d47289666
Signed-off-by: Peichao.Wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28669
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Jett Rink <jettrink@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since each variant has a separate build, we don't need to support
multiple manufacturers in a single file.
BUG=b:79874904
TEST=Build, boot, see updated mainboard manufacturer
Change-Id: I0ccf207ba8d5e5200aa4b19c46784bbda82f7b6e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/28729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
To disable NB-Pstate, the system wouldn't auto restart on EVT board when idling.
BUG=b:116082728
Change-Id: Iec4f0355cb6eb1c2b0372e3d131cc5e6ba36635e
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I3a8e077656df02912b4e67c3947bd5af054a18bf
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The following was tested:
- CPUs with 800, 1067, 1333MHz FSB (1333MHz FSB needs a jumper set)
- The VGA output with libgfxinit
- USB
- COM1
- Ethernet
- SATA
- PCIe
- PCI
Has the following problems:
- The Ethernet NIC is not usable after S3 resume and requires Linux to reload
the driver. Vendor firmware also has this problem so it is quite likely it
is just a atl1c driver problem.
TODO: Add documentation
Change-Id: Ibce9ecdc0e44db3703401f116c9a8bff5b66437f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
STAPM programming was created inside function OemCustomizeInitEarly().
It should be SOC specific, and called by agesawrapper just before the
call to OemCustomizeInitEarly().
BUG=b:116196626
TEST=build and boot grunt
Change-Id: I8a2e51abda11a9d60a9057b38f2a484e1c8c9047
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28705
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit creates an ampton variant for Octopus. The initial settings
are copied from Bip, but the following changes are made to support
hardware differences:
* GPIO_66 is not connected (LTE).
* GPIO_67 is not connected (LTE).
* Updated comment for GPIO_134 (EC_AP_INT_ODL), but not configured yet.
* GPIO_143 is not connected.
* GPIO_144, GPIO_145 mapped to PEN_EJECT are not connected.
* EN_PP3300_TOUCHSCREEN moved from GPIO_213 to GPIO_146.
* GPIO_213 is not connected.
* GPIO_214 is not connected.
BUG=b:111498206
TEST=None
Change-Id: I7d6cf19c906df19115b1101e3d91c62f5f3f61e3
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/28663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add new mainboard variant of whiskey lake rvp, which is primary
validation platform for whiskey lake silicon, support socket DDR4 memory
module.
BUG=N/A
TEST=Build and flash, confirm boot up into kernel on whiskey lake rvp
platform.
Change-Id: I4a5e8a9ec76d5e55e55ef9bf968825c17fbe9816
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch sets the MRC UPD "CmdTriStateDis" to disable TriState for
the rammus boards. Rammus is LPDDR3 design without RTT for CMD/CTRL.
BUG=none
TEST=Run memtester app and also webgl fishtank on the LPDDR3 kabylake
boards and also check the margin data is proper in FSP.
Change-Id: Iee115f49ba5b36dc5b0425e9da02b58cd19b2236
Signed-off-by: Marx Wang <marx.wang@intel.com>
Reviewed-on: https://review.coreboot.org/28568
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's only DDR4 or LPDDR3 support for coffelake processor line,
details can be found out on EDS #570805.
BUG=N/A
TEST=N/A
Change-Id: I8ba6b6861b15b40b01237f87c8d55394f7fd6706
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add gpio programming difference for whiskeylake rvp platform.
BUG=N/A
TEST=N/A
Change-Id: I35a0384f828fd3219e0c3adb4830f5bdab800e32
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28367
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set up EC_IN_RW GPIO to boot depthcharge. Without this patch,
depthcharge will fail to tell if the EC firmware is RW.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui and see in logs, that depthcharge detects
EC_IN_RW GPIO.
Change-Id: Icb39d663f65b72e0ad54059c9590d9693106ee25
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/28670
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change GPP_D17 and GPP_D18 to no connects as DMIC was moved
to DMIC0.
BUG=b:113744731,b:111106010
TEST=none
Change-Id: I8ef42627e542182707c81389af9da33a114bc184
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28689
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Grunt variants need a way to customize the mainboard vendor based on the
platform. For future boards, this can probably be done via CBI, but
grunt doesn't support that method.
BUG=b:79874904
TEST=Build, boot, see updated mainboard vendor
Change-Id: I997dc39c7f36f70cf4320ef335831245889eb475
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/28651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@google.com>
|
|
Update Power Limit1 and Power Limit2 values along with stepsize.
Correct the charger effect for Temperature sensor2.
BUG=b:112448519
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: I01e0a94fe694537d9eebe3b92c11d0c83137d716
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/28530
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A negative side-effect is that those boards disappear from the board-status
output, but this is an issue on all variants.
Change-Id: Ic80804dc1f7d9c6f83ceee3db667019532c31d4c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28626
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The board_id() definition is the duplicate of chrome EC board_id
definition. Remove the duplicate definition and select
EC_GOOGLE_CHROMEEC_BOARDID Kconfig item.
BUG=b:114001972,b:114677884,b:114677887
Change-Id: Id8b7027d653649e8e5791e455652c4e893a746c2
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Tested-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reviewed-on: https://review.coreboot.org/28609
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The helper function to get the board version from EC returns 0 on
failure. But 0 is also a valid board version. Update the helper function
to return -1 on failure and update the use-cases.
BUG=b:114001972,b:114677884,b:114677887
Change-Id: I93e8dbce2ff26e76504b132055985f53cbf07d31
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Tested-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/28576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
|
|
Update DPTF settings based on recommendation from thermal team.
BUG=b:112550414
BRANCH=None
TEST=Manually tested by thermal team.
Change-Id: I26f09392a3293ce4b3481f2be341a667d606bc10
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-on: https://review.coreboot.org/28666
Reviewed-by: Todd Broch <tbroch@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable DRAM_PART_NUM_IN_CBI feature to get DRAM part number from CBI
and set DRAM_PART_IN_CBI_BOARD_ID_MIN to 1 for EVT.
BUG=b:115965629
TEST=verified it in meep proto board which rework ram id.
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I962b099d5b9fbe0ca29708be1e9c6ed60b10d363
Reviewed-on: https://review.coreboot.org/28658
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Change-Id: I4fcdb7467f1911af722f4c24ce64807079a91340
Signed-off-by: Evgeny Zinoviev <me@ch1p.com>
Reviewed-on: https://review.coreboot.org/28620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
