| Age | Commit message (Collapse) | Author |
|---|
|
Adjust the touchpad HID/CID/HRV to allow coolstar's crostouchpad
Windows drivers to properly attach.
TEST=build/boot google/parrot, verify touchpad functional under
both Windows 10/11 and Linux, verify Windows overlay driver
correctly remaps top row keys.
Change-Id: Ic164244eceb52221653bd60f7217f9a09e38c1b6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75180
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust the touchpad HID/CID/HRV to allow coolstar's crostouchpad
Windows drivers to properly attach. Change the interrupt type
from EDGE to LEVEL.
TEST=build/boot google/butterfly, verify touchpad functional under
both Windows 10/11 and Linux, verify Windows overlay driver
correctly remaps top row keys.
Change-Id: I971795becfb05fb42921ff6f40a20892f4f5654a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Use board-specific ASL for PS2-attached trackpad rather than the EC/SIO
default, so that Windows installs a multitouch-capable driver rather
than the standard PS2 mouse driver.
TEST=build/boot Win11 on google/stout, verify trackpad is multitouch
capable.
Change-Id: Id93bbe53f35b1e2c35e36d8175889786b9f5de8b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75176
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
VMX is enabled through a bit in the IA32_FEATURE_CONTROL MSR, which can
be locked. The MSR remains locked after a non-power cycle reset, though.
If the MSR is locked, coreboot bails out and leaves VMX in the state it
was found. Because of this, changes to the VMX enable option in the BMC
only take effect after the system is power cycled.
This behaviour is highly undesirable because users are likely not aware
that a power cycle is required for changes to VMX state to take effect.
So, if VMX is supported, the IA32_FEATURE_CONTROL MSR is locked and the
current VMX state does not match the requested state, then issue a full
reset. This will power cycle the system and unlock the MSR, so that the
desired VMX state can be programmed into the MSR. This is checked early
to avoid needlessly doing time-consuming operations (running FSP) twice
if we know we will need to power cycle the system anyway.
Note that a user may change the VMX setting after the newly-added check
but before the setting is read in ramstage to program the MSR, but this
is a non-issue as firmware settings need a reset to take effect anyway.
TEST: Toggle VMX setting in BMC and reboot without power cycle, observe
coreboot automatically issues a power cycle reset because the MSR
is locked and the VMX state differs. Verify that the system boots
properly with VMX in the correct state after having power cycled.
Change-Id: Id9061ba896a7062da45a86fb26eeb58927184dcb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Instead of having the maximum number of possible CPU objects defined in
the DSDT, dynamically generate the number of needed CPU devices in the
SSDT like it's done on all other x86 platforms in coreboot.
TEST=APU2 still boots and Linux doesn't show any ACPI errors with this
patch applied and it prints "ACPI: \_SB_.P000: Found 2 idle states".
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id6f057ad130a27b371722fa66ce0a982afc43c6c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73073
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The `get_board_settings()` function always returns non-NULL, so there is
no need for NULL checks. When only one member is accessed, also drop the
local variable and directly dereference the function's return value.
Change-Id: I4fc62ca2454f4da7c8ade506064a7b0e6ba48749
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75140
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
This mainboard contains in addition to its base variant, mc_ehl2, an LCD
panel driven through the PTN3460 eDP-to-LVDS bridge.
This patch enables the PTN3460 support by adding the device to
devicetree.cb and board-specific configuration parameters in
lcd_panel.c.
BUG=none
TEST=Boot with the LCD panel attached and observe whether the picture is
stable and free of artifacts coming from wrong resolution and timing.
Change-Id: I196d7ceeb7ac241c9b95db2ef791a5f3ff7890a7
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard is based on mc_ehl2. In a first step, it contains a copy
of mc_ehl2 directory with minimum changes. Special adaptations for
mc_ehl5 mainboard will follow in separate commits.
Change-Id: Id80f8eb49dd2fed0ed1ffc479d47d8669eca84c9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Based on touchscreen product spec.
For uldren variants with a touchscreen, drive the enable GPIO high
starting in romstage while holding in reset, then disable the reset
GPIO in ramstage (done in the baseboard).
BUG=b:279989974
TEST=Build and boot to OS in uldren. Touch screen is workable.
Change-Id: Ib1b1ce80aa1dd8c312e3663fc50c9e9f53cc07fe
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74835
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Replace `memupd->FspmConfig.` with `mcfg->` for the sake of brevity.
Change-Id: If2e7cccca955b0c1e07c1ecf100d29a923107856
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75136
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
|
|
This signal isn't functionally being used and is causing leakage
during suspend. Set it to NC.
BUG=b:279762779
TEST=builds. WWAN functional.
Change-Id: I93f2b0a781e250678280b57e4ab1d80ef27ff460
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
If reading the serial/part number fails, returning an empty string is
very confusing. Instead, return "INVALID" to make problems obvious.
Change-Id: I3c174ca76d51b44456c7b68f4fcffb4c8f9379be
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
|
|
The Realtek RTL8111F NIC is currently not defined at all, nor as a child
device, resulting in the on_board flag not being set to 1. This means
that Linux / udev will call the device enp3s0 rather than eno0, as it's
appropriate for on-board ethernet devices.
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Change-Id: I95f01a466a59234d1cbe2420f208bf58ae28fcc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This board has a TPM connector, enable support for it.
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Change-Id: I1861df95eef15bc2bd29412240d61456eaaad8c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75105
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Small typo in brask/gma-mainboards-ads
Should be brask/gma-mainboards.ads
BUG=b:277861633
BRANCH=firmware-brya-14505.B
TEST=Builds
Change-Id: I9800870dcef13a3e16f6235137e79234a5e6bf83
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75052
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Create the gothrax variant of the nissa reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.).
BUG=279614675
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_GOTHRAX
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: I129e4a55e4b87091e425a45392024d04f3977c79
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74748
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
The boxy removed the APW8738BQBI-TRG and
"disable_external_bypass_vr" should be set to "1" to disable
BUG=b:271407334
TEST=emerge-dedede coreboot
Signed-off-by: Kevin Yang <kevin3.yang@lcfc.corp-partner.google.com>
Change-Id: Ic6667e93de41e84f67363ab7554fe755fe50684a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74889
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create overridetree and GPIO config based on latest schematic:
1. Update PCIe ports
2. Update USB ports
3. Remove unused I2Cs
4. Remove unused peripherals (SD card, eDP, speakers)
5. Add LAN
6. Thermal policy for updated temp sensors
BUG=b:277529068
BRANCH=dedede
TEST=build
Signed-off-by: Kevin Yang <kevin3.yang@lcfc.corp-partner.google.com>
Change-Id: I5a155ebca50dbd5bdb046713ebabbee395361273
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74626
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
For the sequenced controlled shutdown path, there's a 10ms delay
after the PEXVDD rail is disabled to permit discharge needed on
Agah/Proxima.
This can be dropped to 3ms for Hades designs Proto0 and forward.
Once Agah board is dropped, "if CONFIG" can be cleaned up/removed.
BUG=b:271167335
TEST=builds
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Change-Id: I8a0d62ec76caff861adce2d6c0ba2d4e4064affa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75051
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With the introduction of a new Linux version a problem has appeared
after a software initiated reset via CF9h register. The problem
manifests itself in the fact that the Linux kernel does not start after
the reboot. The problem is solved by setting bit 3 to 1 in Reset Control
Register (I/O port CF9h). This leads to the fact that the PCH will drive
SLP_S3 active low in the reset sequence. It leads to the same behavior
as in commit 04ea73ee78bc ("siemens/mc_apl3: Set Full Reset Bit into
Reset Control Register") explained.
Change-Id: Ia8b7f997ca6234add569da751e1070144790e258
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: I6578aee52e6900b25441dc119383856acc480231
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
An underscore has crept into the mainboard model option for mc_ehl3 and
mc_ehl4 by mistake. This patch fixes the incorrect entry.
Change-Id: Ie59619877fb6341a5bbfe91c13e7692943480ad0
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75040
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are only SSD connected to SATA ports on this mainboard. To prevent
misbehavior, set the correct hard drive type for enabled SATA ports.
BUG=none
TEST=Boot into OS and check the stability of the SSD
Change-Id: I116b1e36f0582956604c3c2508961ffb3de0898a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74947
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Follow the EC GPIO programming sequence to enable the MXM PCIe slot.
Change-Id: I75d7ac488bb005751e6f674ab9a2fd99baad571b
Signed-off-by: Anand Vaikar <a.vaikar2021@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
All other boards use MAINBOARD_ prefix instead of board name.
Change-Id: I97d9d28963c97e780156d75b39deac069028866a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Change-Id: I4d34e5c094440dad4a6ab9adc67d3da6b71ac2bf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74514
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Change-Id: If4b7c2b94e0fec84831740336ccdbea0922ffbfe
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74513
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name.
Change-Id: I2ae03a3ac548674b8c5e7dfaff47d6c536b452f1
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75013
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3881c152663a038833d8126d7f24f2a6688426d1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74515
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The STA_HIMAX83102_J02 and STA_ILI9882T panel will be used for Starmie,
enable these two panels config for it.
BUG=b:272425116
BRANCH=corsola
TEST=build starmie and check the cbfs include the panels
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I1dd696dd6a84d9606e4b9a2d4884dd70a6df9161
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74200
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Librem Mini v1/v2 has an automatic power-on setting provided by the EC
in BRAM bank 1. Use this bank as the high bank of CMOS memory so that
setting can be described in cmos.layout.
Change-Id: Icb87bc521f71aa4350c8f5a64fc2cbe7a7a8c808
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Add FW_CONFIG item for FP sensor init and conditionally init
the GPIOs based on whether we're using a SPI or UART FP sensor.
BUG=b:276939271
TEST=builds
Change-Id: I9815bd17df1d15f73529beb15d08cde1ef90efad
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add FW_CONFIG item for eMMC/NVMe support and address the init
of the lanes based on said config.
BUG=b:278877257
TEST=builds
Change-Id: Id6452f497cf78549b7d6126f1b55cd6d45b403c3
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74957
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Mark Hasemeyer <markhas@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Allow different gma-mainboards configs for different baseboards
as they support varying display interfaces. Set Brya to eDP only
and Brask to HDMI only.
BUG=b:277861633
BRANCH=firmware-brya-14505.B
TEST=Builds and SoL functions on both brya and brask varaints
Change-Id: Iaf3f35b009d53e50723e4aa82c0f4932783f9bb9
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
Denote the correct value of ACPI _PLD for USB ports.
The horizontal position of port C0 is incorrectly labelled.
+----------------+
| |
| Screen |
| |
+----------------+
C0 | | A0
| | C1
| |
+----------------+
BUG=b:216490477
TEST=emerg-rex coreboot
Signed-off-by: Won Chung <wonchung@google.com>
Change-Id: Id9ed435ca0af131e3bb4538701fc97d78146899f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74366
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update eMMC DLL settings based on Uldren board.
BUG=b:280120229
TEST=executed 10 cycles of cold boot successfully
Change-Id: I46e2f9df0e82e66fa3ae32aa87b4bcf30d5737ab
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Update devicetree to support G7500 touchscreen.
BUG=b:273791621
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot and check touchscreen function
Change-Id: I3b63b1bb45275ad7eef8799dcff27f264739c258
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Change-Id: Id5b0fa96ca8d86ddf20d808f5107a43ad2d0a1e0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Change-Id: I0ada381883aa65d36434486dcce6b2331599e5c3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I47ec05aa87e4e7c02b19817b2f703eca492008e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add DDR DQ map config for screebo
BUG=b:276814951,b:272218757
TEST=emerge-rex coreboot
Change-Id: I993ae4024689b9cedbea247689a760bd83cd0d45
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74961
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Add variant makefile to support including the memory folder for Myst.
BUG=b:273383819
TEST=Builds in chromium with blobs
Change-Id: I03b0cd91dd66f357b15522da36f5118867b6b14c
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74964
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the OEM ID from CBI to determine the correct OEM board name.
ID mapping taken from ChromeEC source, branch firmware-fizz-10139.B.
TEST=build/boot multiple fizz variants, check that board name reported
correctly in SMBIOS tables.
Change-Id: I06251974ac73570b911920ed566a175e8e733710
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Override SMBIOS product name with sub-variant name based on board SKU.
TEST=build/boot multiple nami variants, verify SMBIOS product name
reports correctly.
Change-Id: I2125bfb6436469405378f9c983d7cfcb2f85f916
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
DSM (Dynamic Speaker Management) uses calibration parameters stored in
a VPD (Vital Product Data) FMAP region to configure the audio output
via an ACPI _DSD table. This has no dependency on a ChromeOS, and can
be used by Linux/Windows drivers if appropriately configured.
Remove the dependency of DSM_CALIB (and the calibration file) on
CHROMEOS and replace it with VPD, so that non-CHROMEOS builds
can utilize this feature as well. Move files from underneath
vc/google/chromeos to underscore the point.
TEST=build/boot google/nightfury, dump ACPI, verify DSM calibraton
parameters present in _DSD table.
Change-Id: I643b3581bcc662befc9e30736dae806f94b055af
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74812
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Only expand these strings in lib/identity.o.
Change-Id: I8732bbeff8cf8a757bf32fdb615b1d0f97584585
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The patch disables Tccold Handshake to prevent possible display
flicker issue for marasov board. Please refer to Intel doc#723158
for more information.
BUG=b:279117758
BRANCH=firmware-brya-14505.B
TEST=Boot to OS on marasov.
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I286e88e5bec240d64e6c801648f6483ad2b0939c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74931
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Configure the SuperIO and logical devices in the device tree. This
overrides the power-on default state.
UART1 was already enabled, and if ENABLE_EC_UART1 was selected in
Kconfig, the LPC UART1 I/O range was also already enabled.
The RTC/BRAM interface was enabled (and the BRAM1 base was 0x360 by
default), but the LPC I/O range was not opened previously. Now it is
open and BRAM bank 1 is accessible.
Mouse/Keyboard are not wired to anything on this board and are now
disabled.
UART2, SMFI, power channel 1, and power channel 2 were enabled
previously, but their LPC I/O ranges were not opened and they were not
accessible to the OS. Fan control is performed by the EC on this board
so there is no change.
SWUC and power channels 3-5 were disabled by default, no change.
Change-Id: I58a5a427737f4a2caa64326c110eb53ec00b347d
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74369
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
variant_board_sku() is missing dependences in order to work correctly
in romstage. Rather than more intrusive rework as its use is limited,
move the FPMCU early GPIO init back to ramstage. We still meet
sufficient power off time to fully power cycle the MCU.
BUG=b:245954151
TEST=Confirmed FPMCU is still functional on Nami and FP tests all pass
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Change-Id: Ia428ec5aec1a0438e91bc48903bda043046b740e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74695
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The image processing unit/GMM and xDCI are not used on octopus boards;
additionally, enabling xDCI can cause some problems with USB ports in
both booting from the payload and in the OS.
Change-Id: I1ee99b5c45881a4cf3624bf487bc9d83fb3d07a1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add SOF chip driver entries for all variants, so that the correct audio
config is passed to the OS drivers.
TEST=build, boot Windows on wyvern variant, verify headphone output
and microphone functional under Windows using coolstar's SOF drivers.
Change-Id: I421c070eac321c2fc160b8f26868bcb1ec13001e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74815
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Add SOF chip driver entries for all variants, so that the correct audio
config is passed to the OS drivers.
TEST=build, boot Windows on several volteer variants, verify audio
functional under Windows using coolstar's SOF drivers.
Change-Id: I62a96149cec9eeb7b2da8a2337083969a1b0fce0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74816
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Add SOF chip driver entries for all variants, so that the correct audio
config is passed to the OS drivers.
TEST=build, boot Windows on banshee and osiris variants, verify audio
functional under Windows using coolstar's SOF drivers.
Change-Id: I12614b85f9779cc40d83a9c868cc46b110f26af6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74817
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Add all SOF chip drivers to baseboard and use FW_CONFIG to determine
the correct option, to ensure the correct audio config is passed to the
SOF OS drivers.
TEST=build, boot Windows on several dedede variants, verify audio
functional under Windows using coolstar's SOF drivers.
Change-Id: I9452b11af614d8727aa8dd448e37f7a06faa450d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74818
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Since commit 833bb448c521 ("mb/siemens/mc_ehl: Remove spd.bin from
CBFS"), the subdir 'spd' is no longer necessary.
Change-Id: Ibaf44e3181b2167aa83cffcc59835196e4cb5cdb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Remove explicit PNP 6e.1 configuration for UART. This had no effect,
the SuperIO is actually on I/O port 2e. Enabling the 8250IO driver is
sufficient to use the UART, the UART device is enabled by default.
Test: Build Mini v2 with and without CONFIG_ENABLE_EC_UART1, boot and
check output on serial.
Change-Id: Idbb39c81cadd633f4718f0682d231dc578d20325
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74362
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tuning i2c frequency ,timing ,Waveform meet to SPEC
i2c frequency :
I2C0=>399.8khz / Setup Time:1765ns / Hold Time:82.35ns.
I2C1=>390.4khz / Setup Time:1.788us / Hold Time:70.58ns.
I2C3=>308.7khz / Setup Time:1.482us / Hold Time:0.4us.
I2C5=>390.8khz / Setup Time:1.218us / Hold Time:0.405us.
BUG=b:275061994
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot,
EE check OK with test FW and TP function is normal.
Change-Id: I5b77cd3fd3ff00804f1b8dd5828dc831a9732566
Signed-off-by: Jamie Chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74880
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
|
|
The patch orders MTL RVP board Kconfigs alphabetically.
TEST=Build the code for mtlrvp
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ib8557aab2848a384fba5203e5f3d62407b2566ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
|
|
We have largely dropped from filling in mainboard_ops.name
as unnecessary. A common place should be decided where or if
this information is added in the console log.
Change-Id: I917222922560c6273b4be91cd7d99ce2ff8e4231
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Add SOF chip driver entries for all variants, so that the correct audio
config is passed to the OS drivers.
TEST=build, boot Windows on several hatch variants, verify audio
functional under Windows using coolstar's SOF drivers.
Change-Id: Ie791fa873fc7bbab84644f5ea5743bdcdc124908
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
The image processing unit (Iunit) and SoC UARTS are not used on any
reef boards.
Change-Id: Iacdf93b4952cbc63fc465f07d440463106527b8d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
It's not particularly useful to end users, and shows up as an unknown
PCI device under Windows Device Manager.
TEST=build reef, boot Windows, verify unknown PCI device no longer
present in Device Manager.
Change-Id: Ie8ec46e2e07b6635bfe9766812ce08b866c71d66
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add rules to inject the variant specific SPD binaries into APCB.
BUG=b:273383819
TEST=Build Myst BIOS image. Currently no APCB is present. So no SPD is
injected into APCB.
Change-Id: Ic511cdc4fe0989c9abc0cd0531cc0cae40f8dc34
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74746
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Generate the RAM Strap IDs based on the initial memory configuration.
BUG=b:272746814
TEST=Build Myst BIOS image.
Change-Id: I8a4fe9a41f101ac10391756f1b815220c8b98612
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
There is no platform-level implementation for USB port power management
in various sleepstates. This mainboard never evaluates the set GNVS
variables S3U0, S3U1, S5U0 and S5U1 in ASL or in its SMI handlers.
Change-Id: Ic7af2d608d95c6691f31ef1b8af72f96da20787c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
There is no platform-level implementation for USB port power management
in various sleepstates. The mainboards changed here never evaluate the
set GNVS variables S3U0, S3U1, S5U0 and S5U1 in ASL or in their SMI
handlers.
Change-Id: Ia1bc5969804a7346caac4ae93336efd9f0240c87
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
|
|
Change-Id: I634af65cd41e0d70e673d550ed8063abc6eea6d4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Add data.vbt files for all variants supported by current volteer
recovery image. Several boards use the same VBT, so place the "common"
VBT under the baseboard directory and set it as the default.
For variants with a unique VBT, override the default and use the file in
their respective variant directory. Select INTEL_GMA_HAVE_VBT for all
variants which have a VBT file.
TEST=build/boot various volteer variants
Change-Id: I728ab81938c78f600ff8931a8073d1f7de152c09
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74852
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Camera LED will blink several times as sensor is being probed during kernel boot.
Configure _DSC to ACPI_DEVICE_SLEEP_D3_COLD so that driver skips
initial probe during kernel boot and prevent privacy LED blink.
BUG=b:274634319
TEST=Build and boot on Craask. Verify & observe Camera LED blinking behavior.
Change-Id: I78ed5efe1e2c071d817c1e0455271886e89e63c7
Signed-off-by: Jimmy Su <jimmy.su@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74728
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The support for a spd.bin from CBFS was removed for all mc_ehl boards in
commit 833bb448c5213 (mb/siemens/mc_ehl: Remove spd.bin from CBFS).
There is still a remaining comment in romstage_fsp_params.c referring to
the removed capability. This fix removes the spd.bin related part of the
comment to stay consistent with the code.
Change-Id: I669ee1c33d1d1c47764640982f71129195e63f14
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74801
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
With the profile ATLAS_PROF_REALTIME_PERFORMANCE it is desired to not
have the option to be able to enter sleep. The reason is that Microsoft
Windows goes to sleep after 30min of inactivity by default.
TEST: See that Microsoft Windows 11 has no 'Sleep' option in the start
menu.
Change-Id: I424db7e712a705c628aa3a10a486d3313404987a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74421
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
FSP is fractionally faster at configuring ASPM (1,118,688 vs 1,122,205)
but coreboot's configuration results in lower power consumption of
approximately 0.5W when idling - the reason why is unknown.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ib15eaede956f0aa55118d093fdff0fd9487df250
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74520
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add functionality to ensure that the FPMCU is power cycled long enough
on boot to ensure proper reset.
This solution relies solely on coreboot to sequence the power and reset
signals appropriately (150ms on boot).
-Confirmed power is off for 150ms on boot.
-Confirmed RCC_CSR of FPMCU indicates power cycle occurred.
-Confirmed reset is de-asserted approx 3ms after power application
(target >2.5ms)
BUG=b:245954151
TEST=Confirmed FPMCU is still functional on Nami and timings are
as expected.
Change-Id: I0a23bda96bc2ea90be81a2310605f75c55c0a839
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add functionality that allows a variant SKU to have a specific set of
GPIO configs in romstage (modeled after the existing one in
ramstage)
BUG=b:245954151
TEST=builds
Change-Id: I593a23951306908fadc00e6bc8d9d310f09c5e4b
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Generate RAM IDs for -
MT62F512M32D2DR-031 WT:B (LP5)
H9JCNNNBK3MLYR-N6E (LP5)
MT62F1G32D2DS-026 WT:B(LP5x)
H58G56BK7BX068 (LP5X)
BUG=b:276814951
TEST=Run part_id_gen tool without any errors
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I0fb2e488c06ed74d3fd493e5ca0ab89a825a9349
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74802
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The number of NID entries was too high for the Realtek
and Intel sound cards, preventing the verb table from
loading. Now the values are correct; it loads as intended.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I79825313a4801c120a0a2a321cbabab7c728aa71
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Commit 5103b87a4d7b ("mb/starlabs/starbook/adl: Add an option to
enable Hot Plug") introduced an option to enable Hot Plug for the
SSD. The port was set to 4 (RP5) which is the wireless card. Change
this to 8 (RP9) which is the SSD.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I884f4997d73e31bd422477952466f168afad66a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74738
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
add the initial gpio configuration for screebo initial variant
BUG=b:276814951
TEST=emerge-rex coreboot
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Change-Id: Ib96e03f47bc1d6e5628ae459c3e1eb4dc18849c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74475
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Because SPL fuse needs to be set before the FW lock. So enable
Markarth project to send the fuse SPL (security patch level)
command to the PSP.
BUG=b:279499511
BRANCH=none
TEST=FW_NAME="Markarth" emerge-skyrim coreboot chromeos-bootimage
Then get "PSP: SPL Fusing Update Requested." in the firmware log.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I8fbbd89d11b1bdb2c95c761955c10bedb366fd70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74753
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update Samsung 4G K3KL6L60GM-MGCT support
BRANCH=None
BUG=b:243337816
TEST=emerge-skyrim coreboot
Change-Id: I89b9798c16635a32dff12f1c0b65737d3c16cd59
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This patch adds new USB_DB FW_CONFIG to enable support for USB4 ANX7452
Rev 2.
BUG=b:279647370
TEST=Able to build and boot google/rex with Proto 2 SKU
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I878b591e5919d05d3c5fc2eefdeb492e95d4f7b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Set edp_panel_t9_ms to 8ms which means it will delay 8ms
between backlight off and vary backlight off.
BUG=b:271704149
BRANCH=Skyrim
TEST=Build; Verify the UPD was passed to system integrated table;
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I952d05b18e29cf30256f43562a5052007c5c6268
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74790
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename the UPD pwr_on_vary_bl_to_blon to edp_panel_t8_ms to
match the eDP sequence timing in milliseconds.
BUG=b:271704149
BRANCH=Skyrim
Test=Build/Boot to ChromeOS
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Iecdfe47cd9142d8a1ddeee0ec988d37b2a11028e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74787
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Update devicetree to support ELAN I2C generic touchscreen.
BUG=b:273791621
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I2779c2930d89ff42233f9b20bd8abdf6dc00c0e0
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74776
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
The MIPI panels will be used on the detachable variant starmie, and
there will be different MIPI panels used on starmie. In order to make
the different panels functional on unprovisioned devices, it needs
to pass the SKU ID and panel ID to the payload to load the matched
device tree for kernel. From the schematic, the starmie variant
will read the LCM ID from ADC channel 5.
BRANCH=corsola
BUG=b:275470328
TEST=boot starmie and see FW screen display
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I6339dc3c177fb8982f77fb3bd32dc00da735fce4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
|
|
The signals for the NV33 regulator were swapped (enable and power
good). Switch these back to the way they should be:
GPIO_NV33_PWR_EN GPP_E1
GPIO_NV33_PG GPP_E2
BUG=b:269371363
TEST=builds
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Change-Id: Ic2a53103e1feadd7ecebd4bed02dcc34410b8e3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74693
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Change-Id: I8b536f8a1ff4eab06f37aec0f25704525dc1b64e
Signed-off-by: Anand Vaikar <a.vaikar2021@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Because WD SSD drive isn't holding the clock low for some reason.
So we change to read eMMC clkreq signal instead.
BRANCH=none
BUG=b:274377518
TEST=emerge-skyrim coreboot chromeos-bootimage and verify ok.
Change-Id: I1329386631dc54209db54ac146e4aafe95b6a3ac
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
By default, coreboot includes support for all the different types of SPI
ROMs. Excluding the unused ROM types shrinks ramstage by almost 4k.
BUG=b:267735039
TEST=Build & Boot ROM
BRANCH=Skyrim
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: If6e402269d1f2cac8256d478eb36743441497bdf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72769
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Remove rtd3 for emmc device on taeko
BUG=b:271003060
TEST= emerge-brya coreboot, flash to DUT and can boot to OS
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I21191c9762a00ba137892e680d533f7dc3b53e86
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Remove rtd3 for emmc device on taniks
BUG=b:271003060
TEST=emerge-brya coreboot, flash to DUT and can boot to OS
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I03168ecbf4611f05acd8c6c722b6a5037a8cc31d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This will fix:
> [INFO ] Probing TPM I2C: tis_plat_irq_status() not implemented,
wasting 20ms to wait on Cr50!
BUG=b:277297687
TEST=builds
Change-Id: I611a2855d94167748d0f82a478687fe2cdf5846a
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74286
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure PCIe Clk Source and Clk Request mapping. Configure GPIOs used
for WLAN. Mapping derived from myst schematic.
BUG=b:275965982
TEST=Builds
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: I5059be0bc011978e74ab4245e6ae037aa177ef9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Ensure that DXIO descriptors are updated using info from AMD and Myst
board schematics.
BUG=b:275960920,b:276744321
TEST=builds
Change-Id: Icdad785bcb90de036095bcc4219c15f55f4277fe
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74112
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This mainboard has SD slot available and therefore it should be enabled.
Use the same SD card configuration as for mc_ehl2 mainboard.
Change-Id: Icd9b25301311679cf93b05ba83a24e551261a020
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard has the RTC RV-3028-C7 connected to the I2C1.
TEST:
- Console Log shows no errors for RV-3028-C7 during I2C1 init
- Finalize device for I2C 00:52 shows correct date and time
Change-Id: I1b4115d7844a0c218fdf92cb1af2da5a95eb4337
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74652
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct the USB settings, suitable for this mainboard.
Change-Id: I943eb891e2f2d967acfd441c085063dbad49e993
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74651
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since mc_ehl4 was only a copy of mc_ehl1 in a first step, the default
value of the Kconfig switch EARLY_PCI_BRIDGE_FUNCTION must be set to
'0'. On this mainboard NC FPGA is connected to PCIe root port #1
(00:1c.0).
Change-Id: I15035523d8575d486c3f2d0ffe3916712ee89d7d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Since mc_ehl4 was only a copy of mc_ehl1 in a first step, the GPIOs must
be adjust according to the circuit diagram for this mainboard.
Change-Id: I66bfbb380e9a05b3a2c08d5d1980e9749b46ee43
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The patch disables Tccold Handshake to prevent possible display
flicker issue for Omnigul board. Please refer to Intel doc#723158
for more information.
BUG=b:279539826
BRANCH=firmware-brya-14505.B
TEST=Verify the build for Omnigul board
Change-Id: I04e54df5afe09c12e1cf774445d57e13ffd8819e
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74737
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
