| Age | Commit message (Collapse) | Author |
|---|
|
Needs the ramstage configuration enabling of SuperIO GPIO pnp devices
for BSEL straps.
Also needs VSBGATE# to be on for ram to be powered during S3.
TESTED with 800MHz and 1067MHz FSB CPUs at the correct straps when
resuming from S3.
Change-Id: I6ac927ee9dcce15fc7621aad57969fae8f5805ca
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enable Azalia controller, HD Audio DSP and select
the HDAudio IoBuffer Ownership for rvp3.
Check if device is enabled in HDA codec init function
to avoid failure when Azalia controller is disabled in
the devicetree.cb.
BUG=None
TEST=Build for kblrvp3, Make sure booting is fine irrespective of HDA
enable/disable.
Change-Id: I87212fe16ecc6053d6d00372904a5fd5d6f6b209
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20530
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
1. Due to reset signal, PMIC loses its internal register state. This
causes PMIC to be in improper state after sleep.
2. The intent of reset signal is to reset internal state of PMIC (which
happens once during power on), hence avoid asserting reset signal
when not needed.
3. As per PMIC (TPS68470) datasheet, device can be kept in SLEEP mode
when not in use to save max possible power.
To fix the same, do not reset PMIC while entering sleep.
By keeping PMIC in SLEEP mode, Power consumption is < 1uW (Typ) upto
3.63uW (Max). Refs: TPS68470 datasheet.
Measured value: 0.66uW
TEST= Build the firmware for Soraka & boot to OS. Do S3 resume & check
whether PMIC internal registers state are preserved.
Change-Id: I93ce4d76b0376b64ae6d1067aca0fd7467af3582
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20264
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We remove this particular header file already while remaining
of include fixes is longterm and pending work.
Change-Id: I869d426c1344290a00e2df60e07e9a4a3ae26887
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Chell doesn't have a touchscreen, so remove the driver
definition from devicetree. Leave the PCI device function 0
enabled since disabling results in the touchpad (function 1)
being disabled as well.
Change-Id: I32619b7618bc0cdd99fa54fdda9bf2b5c1bb79a4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I63c6febf8ba953a642fd7b04a555a4c6704abc79
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
With the existing SSID, the driver loaded by Windows results
in the headphone jack and internal mic being non-functional.
With the new SSID, the a functional driver is loaded and
everything works correctly. Linux works correctly with
either SSID so the change has no impact there.
New SSID extracted from Windows drivers (.inf).
Change-Id: I4195d00d6b18dcd0039747d9883cdf8e1a76f461
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Fix comments to reflect correct manufacturer/model, SSID.
Change-Id: Ibaa39fbb8081393ef4696c6f2470a546e801f483
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Port commit f1395d82: "ec/lenovo/h8: Add USB Always On"
to other Thinkpad boards, as it seems to work fine on all
generations.
Change-Id: I6dcbfaae2a444d9a679ecb64a87dc2a59b8fd281
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Add support for UAO AC only mode.
Needs tests on all platforms.
Change-Id: Ib52aab427ff687b00129024cde65b78060d21e32
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Change-Id: Ifba3257b0328d0b6ad1bee9bf885683998df5851
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I1f906c8c465108017bc4d08534653233078ef32d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Icca8bac5e67f83dfc5a8f5ef1cb87c6432e0a236
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ie8347a3eccce51de3e938d0c3c170e59a9f74716
Signed-off-by: Ryan Salsamendi <rsalsamendi@hotmail.com>
Reviewed-on: https://review.coreboot.org/20442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I6ccbbee00aab947079c3471fcf83ae9a66c01d59
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/19754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Toggle LEDs after successful dock and undock.
On boot the LED will light up and on undock button
press the LED will turn off again.
Tested on Lenovo T500.
Change-Id: Ib5851f4abcedf4041faae6b3b810102012f488cd
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Use the new PAD_CFG_GPI_INT macro to specify the headset codec
interrupt as specifically edge triggered (since it is registered
as EDGE_BOTH in the devicetree) in order to prevent the interrupt
from firing unexpectedly when the system is resuming.
Also change the DSP interrupt to edge triggered since the kernel
is registering with IRQF_TRIGGER_RISING in order to prevent an
interrupt storm when it asserts.
BUG=b:35582164
TEST=manual testing on Eve:
1) ensure the headset codec sends interrupt on insert and remove
2) ensure there is only one interrupt counted when DSP asserts irq
Change-Id: I40a8ee667de653e4e70770cd96b6417442c1b0ec
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Make this pin a GPI as it is supposed to be an input from the touch
controller and not driven by the AP.
BUG=b:35581264
TEST=check pin state with a scope
Change-Id: Ife5f84fcc614255b20e44389279d515a12f5751d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Board changes in rev6+ have a fix to VDDQ that should fix the issue
that was being seen with this SKU, so only lower the memory speed on
older boards.
BUG=b:37172778
TEST=memory stress testing on rev6 boards
Change-Id: I6d6fe730cabd74af23eab3f02feef9da01a35fd4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add support for waking from and logging device events that
originate in the Embedded Controller. As this device uses
Deep S3 it relies on the EC to wake the AP from the trackpad
and DSP wake sources.
BUG=b:30624430
TEST=manual testing on Eve: wake from Deep S3 via trackpad and
DSP and verify the event log contains the expected device event.
Change-Id: I0d6a9c5bfd4cea85e13446ffaa6fe3dab0db96a2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The Chrome EC event for "thermal overload" was never implemented and
is being repurposed as the EC event mask is out of free bits.
Remove this from the boards that were enabling it.
BUG=b:36024430
TEST=build coreboot for affected boards
Change-Id: I6038389ad73cef8a57aec5041bbb9dea98ed2b6e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Set RX6110SA RTC backup mode to primary cell. This mode reduces the
backup current consumption of the RTC.
Change-Id: I7c0c26a0ed5d8f48587acc917f8bb1c5c2b8869a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The used RTC6110SA has issues to enter backup mode when the power supply
decreases too slow when the mainboard is turned off. Switch to backup
mode "primary cell" to make sure backup mode will be entered correctly
on power-off. In addition set IOCUTEN to minimize the backup current
consumption of the RTC.
Change-Id: I9733aa9f2981a25f6d42279eff0c4980e5eb5a5a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Use the plain address instead of the weird shifted encoding (e.g. if
we'd use `0xa0` as address, it's actually `0x50` encoded into a write
command).
Change-Id: I6febb2e04e1c6de4294dfa37bde16b147a80b7a8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
There are up to two on-board PCI devices where bus master has to be
enabled in PCI config space. As there is no need for a complete PCI
driver for these devices just set the bus master bit in
mainboard_final().
In a perfect world that would be the task of the runtime driver which
unfortunately don't do that.
Change-Id: Ic2896d5e7568a455737af26b14b2c398caae5f72
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I6ede71ec660678bb5f77693a9095aa0f198e4e26
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/19752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
- Describe RT5663 headphone codec in ACPI so it can
be enumerated by the OS.
- Supply NHLT binaries for RT5663
BUG=b:62872377
TEST=Apply full patch set and UCM, verify basic audio works.
Signed-off-by: Kevin Cheng <kevin.cheng@intel.com>
Change-Id: I5bbd58b0e660cdf5089e6a6dd35a757ecf8ec076
Reviewed-on: https://review.coreboot.org/20305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In the code we do the following in a number of places
to pre-initialize an array with a certain value before
overwriting some of the array with other values:
u8 mainboard_picr_data[FCH_INT_TABLE_SIZE] = {
[0 ... FCH_INT_TABLE_SIZE-1] = 0x1F,
}
clang does not like that behavior unless we specify
the option -Wno-initializer-overrides.
Remove the check for gcc in those places, too, because
1) it would silently change array contents between compilers
2) the check isn't sufficient to determine compilation on
clang vs gcc
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I93cc121b6fec099fcdbd5fd1114c2ff7cbc291dc
Reviewed-on: https://review.coreboot.org/20384
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Update Psi2Threshold, IccMax, AcLoadline, DcLoadline
VR config settings as per board design.
BUG=b:62063434
BRANCH=none
TEST=Build and boot soraka.
Change-Id: I254bbb88b82ddf278f0ec71bc98873df1d5e0d27
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: G Naveen <naveen.g@intel.com>
Reviewed-on: https://review.coreboot.org/20309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Soraka uses MPS2949 IMVP8 controller and does not need the VR
workaroud similar to Eve.
BUG=None
TEST=Build & boot on soraka. Ensure IMVP8 controller goes to low power
mode in S3 and S0ix by measuring power.
Change-Id: Ib98bb709ecc9e362a5cef437e7319e41f398a73b
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Reviewed-on: https://review.coreboot.org/20255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This requires to also unify the calling convention for
AGESA functions from
AGESA_STATUS (*agesa_func)(UINT32 Func, UINT32 Data, VOID *ConfigPtr)
to
AGESA_STATUS (*agesa_func)(UINT32 Func, UINTN Data, VOID *ConfigPtr)
On systems running 32bit x86 code this will not make a difference as
UINTN is uintptr_t which is 32bit on these machines.
Change-Id: I095ec2273c18a9fda11712654e290ebc41b27bd9
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/20380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: I8b02596b116c0b164e83e7b02449c547224a50a6
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/20330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The ChromeEC board directories for auron and rambi have been removed
from the latest version of ChromeEC. Remove them here so the submodule
can be brought forward.
Change-Id: I763d03009f735d3f8aedbeb44788d03714c86102
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
Update the world facing camera sensor to OV13858 and also
add delay of 5ms after xshutdown rising which indicates system
ready status.
BUG=b:38326541
BRANCH=none
TEST=Build and boot soraka. Dump and verify that the generated DSDT table
has the required entries. Verified that sensor probe is successfull.
Change-Id: I0cd535e6568f104ffaa1092a13667def646df0eb
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Add clock frequency property into _DSD ACPI object and set it
to 19.2MHz for camera sensors. Upstream camera kernel has added
a check for clock frequency in sensor probe function and without
this property sensor probe fails.
BUG=b:38326541
BRANCH=none
TEST=Build and boot poppy. Dump and verify that the generated DSDT table
has the required entries. Verified that sensor probe is successfull.
Change-Id: I147b3c932a33ae034868f7f9b616500d24ca71e3
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20294
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Correct all checkpatch errors but leave two errors in place
that are caused by AMD typing.
Change-Id: I9daa374da76ff991de72d16bad0e8b586aa95525
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Switch Garnenia mainboard to single soc/ directory structure.
Change-Id: I095804d603bcccf324d3244965081a9dccba62ae
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
It does not work to enable the LPC range in the function
mainboard_init() because the LPC bus driver closes the range during PCI
enumeration again. For this reason, enabling decoding of the address
range for COM 3 will be done at a later point in time -
mainboard_final().
Change-Id: I452bca4e430b1ea75e4a327591da84500491fe84
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With enabled XDCI support we are not able to use USB port 0 over XHCI
driver. For this reason, we disable XDCI into devicetree.cb.
Change-Id: I1ed721d9ffd44a920a6f1f16855d5b7ceb1b17c5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This board can't be found to be tested, and compiles romstage with
romcc. If desired, it can be continued in the 4.6 branch.
Change-Id: I4826c277bbb444c2f0573729d76cd492ade95b4c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
resources
This patch controls the camera devices power through ACPI power resource.
* Add Opregions for PMIC,
* TI_PMIC_POWER_OPREGION
* TI_PMIC_VR_VAL_OPREGION
* TI_PMIC_CLK_OPREGION
* TI_PMIC_CLK_FREQ_OPREGION
* Add power resources for sensors and VCM,
* OVTH for CAM0
* OVFI for CAM1
* VCMP for VCM
* Implement _ON and _OFF methods for sensor and VCM module's power on
and power off sequences.
BUG=b:38326541
BRANCH=none
TEST=Build and boot poppy. Dump and verify that the generated DSDT table
has the required entries.
Change-Id: I87cd0508ed5ed922211a51f43ee96b6f44cf673d
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/20054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Bind the camera sensor and CIO2 devices through the ports and endpoints
configuration available in _DSD ACPI object.
* Port represents an interface in a device.
* Endpoint represents a connection to that interface.
BUG=b:38326541
BRANCH=none
TEST=Build and boot poppy. Dump and verify that the generated DSDT table
has the required entries.
Change-Id: I6d822165bb9a0cd6f7d4cdcb36333887953110a3
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable RT8168_GET_MAC_FROM_VPD in fizz Kconfig.
BUG=b:62090148, b:35775024
BRANCH=None
TEST=Boot to kernel. Insert mac address into VPD
vpd -s ethernet_mac=<address>
reboot the system.
Ensure we have ip address and corresponding mac
address with ifconfig.
Ensure ethernet controller shows up with lspci.
Change-Id: I00f63dcb56a2c9a4600c8461bc94e06ec5ab2d81
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/20232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
By default disabled. Will need to add
FIZZ_USE_SPI_TPM config to enable.
BUG=b:62456589, b:35775024
BRANCH=None
TEST=Reboot and ensure that TPM works in verstage
CQ-DEPEND=CL:530184
Change-Id: I14ce73a1c3745c996b79c4d4758ca744e63a46b4
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/20134
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:62456589, b:35775024
BRANCH=None
TEST=Reboot and ensure verstage doesn't have any TPM errors
CQ-DEPEND=CL:530185
Change-Id: Icfde0f62bd058d960fcb0c6fc67f9d8f6b9462f5
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/20133
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds mipi_camera.asl,
* Add TPS68470 PMIC related ACPI objects.
* Add OV cameras related ACPI objects.
* Add Dongwoon AF DAC related ACPI objects.
* SSDB: Sensor specific database for camera sensor.
* CAMD: ACPI object to specify the camera device type.
BUG=b:38326541
BRANCH=none
TEST=Build and boot poppy. Dump and verify that the generated DSDT table
has the required entries.
Change-Id: If32a2a8313488d2f50aad3feaa79e17b1d06c80f
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/19621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Remove MIPI camera related register entries from devicetree.cb.
BUG=b:38326541
BRANCH=none
TEST=Build and boot poppy and soraka.
Change-Id: Ic6a6a98d4c8ed6cba760eae5fd87bc2a3f15d7d2
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/19619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fixes 2 reports found by undefined behavior sanitizer. Dereferencing
pointers that are not aligned to the size of access is undefiend
behavior.
Change-Id: Iaa3845308171c307f1ddc7937286aacbd00e3a10
Signed-off-by: Ryan Salsamendi <rsalsamendi@hotmail.com>
Reviewed-on: https://review.coreboot.org/20155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Disable TPM when VBOOT_MOCK_SECDATA is enabled.
BUG=None
BRANCH=None
TEST= Build image using USE="mocktpm" emerge-poppy coreboot depthcharge
vboot_reference chromeos-bootimage . Verify boot is successful with mock
tpm.
Change-Id: Iee527ed17cffb7d25d9089e48a194d99ac8c3cd1
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
RAMD_ID_1 moves to PAD_DSI_TE and RAM_ID_2 moves to PAD_RDP1_A on Rowan.
BUG=chrome-os-partner:62672
BRANCH=none
TEST=emerge-rowan coreboot
Change-Id: Iae44934d8d669d696b83f9d3e3450a0e408fe062
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Gerrit-Rebase-Ignore-CLs-Before: https://chromium-review.googlesource.com/539234
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/388068
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/453778
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/454921
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/455118
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/479613
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/487023
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/498587
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/506785
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/520572
Original-Commit-Id: 4da19b3c00578f96ec933cff9ad0c9988a4c4a30
Original-Change-Id: I64fd29de607a0b360d355fd3724e3a649adc658b
Original-Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/448397
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18583
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The differential signal of DQS needs to keep low
level before gate training. RPULL will connect
4Kn from PADP to VSS and a 4Kn from PADN to
VDDQ to ensure it. But if it has PHY side ODT
connected at this time, it will change the DQS
signal level. So it needs to disable PHY side ODT
when doing gate training.
BRANCH=None
BUG=None
TEST=boot from bob
Change-Id: I56ace8375067aa0bb54d558bc28172b431b92ca5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: cb024042c7297a6b17c41cf650990cd342b1376f
Original-Change-Id: I33cf743c3793a2765a21e5121ce7351410b9e19d
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/448278
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://review.coreboot.org/18582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Use verb table values from AMI firmware, consolidate NID
definitions using azalia macros. Fixes headphone jack detection
and microphone.
Change-Id: Ia31be6efc7afe921ad91b400f66694d951f0a260
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Initialize the audio codec without depending on DSP binary blobs.
The hda_verb.c was copied from the intel/kblrvp rvp7 variant, and the
hda_verb.h file was copied from the purism/librem13.
The IoBufferOwnership FSP option in devicetree has to be 0 for the azalia
driver to work.
Change-Id: Ifa36ac0839daedfa59c497057da0ace04d401f2a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Some NVMe devices (Intel 600p series for example) seem to lock up
in D3 drive power state (L1.2 PCIe power state).
Disabling L1 substates fixes it.
Change-Id: I00a327dc91d443beb565fe4e72aaf816e40a007c
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Enable libgfxinit.
Tested on Lenovo T430:
* LVDS
* VGA
* DP (using DP->HDMI adapter)
All three ports are working. The LVDS port is garbled under linux
when VGA or DP is connected, likely due to missing VBT.
Change-Id: I665661e93724072d1e8412cfcc0e818f824c8cb0
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use a GNVS variable to store the trackpad interrupt, in order to
support both SNB and IVB variants from a single build.
Change-Id: I53df35fff41f52a7d142aea9b1b590c65195bcfd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Existing value was copied from librem13 v1 board, use value
obtained from AMI firmware.
TEST: Observe Windows boots correctly, function keys work
under both Windows and Linux.
Change-Id: I0ea6cc4602ce1047cb803acc65cbca1af1f480b0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add default values for MAINBOARD_VERSION and CBFS_SIZE.
Change-Id: Ib6461cef78f3fea448baf1ada456e3c8335f1543
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
|
|
- remove unused I2C, serialIO defs
- set PL2 override, VR mailbox cmd based on SKL-U ref board,
as values copied from google/chell are for SKL-Y
Change-Id: I3a138c28d0322df6cb41ec1a845ae31602cb69a7
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19941
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Update devicetree USB config based on board spec.
Leave OC pins set to skip since the info is unavailable.
Change-Id: I2a4fe17ed7edacbbbaf56969f9d2801b45a20da9
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The board dutifully registers an int15h handler and provides the
defaults to add a VGABIOS.
That should be good enough to initialize graphics through the VGABIOS
file.
Fixes build on Chrome OS configurations (at least until the Ada toolchain
situation is resolved over there).
Change-Id: I1d956b5a163b7cdf2bd467197fba95f16e5e8fa3
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
As the hardware designed on gru, the AP_I2C_TP_PU_EN (gpio3_b4) controlled
the SCL/SDA status to avoid leakage. And the gpio3_b4 of rk3399 pull
resistor is 26k~71k and 3.3v for supply power, and gpio3_b4 pin connected
2.2k resistor to i2c of TP device.
The default of this gpio status is pulled up during the start to bootup,
it's very weak drive for the TP device that maybe cause to trigger the
recovery process of elan's firmware.
Also, the Elan updated its firmware(102.0.5.0) to delay checking the
i2c of touchpad is greater than 1 second.
So we have to drive the stronger pull-up within 1 second of powering up
the touchpad to prevent its firmware from falling into recovery.
Change-Id: I9a67d1c041afafde24ed9f00716ba41a9b41a8da
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Too low gfx_uma_size can result in problems if the framebuffer
does not fit.
This partially reverts: 7afcfe0 "gm45: enable setting all vram sizes
from cmos"
Change-Id: I485d24198cb784db5d2cfce0a8646e861a4a1695
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
TEST=Verified that board still boots to OS without any error.
Change-Id: I02d2a6cbcab92766a35993bfd20aaeed4ca22c90
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Now that we dynamically disable TPM interface based on config options,
add support for generation of SPI TPM ACPI node if SPI TPM is used.
Change-Id: I87d28a42b48ba916c70e45a061c5efd91a8a59bf
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Based on the config options selected, decide at runtime which TPM
interface should be disabled so that ACPI tables are not generated for
that interface.
TEST=Verified that unused interface does not show up in ACPI tables.
Change-Id: Iee8f49e484ed024c549f60c88d874c08873b75cb
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20141
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
There are many good reasons why we may want to run some sort of generic
callback before we're executing a reset. Unfortunateley, that is really
hard right now: code that wants to reset simply calls the hard_reset()
function (or one of its ill-differentiated cousins) which is directly
implemented by a myriad of different mainboards, northbridges, SoCs,
etc. More recent x86 SoCs have tried to solve the problem in their own
little corner of soc/intel/common, but it's really something that would
benefit all of coreboot.
This patch expands the concept onto all boards: hard_reset() and friends
get implemented in a generic location where they can run hooks before
calling the platform-specific implementation that is now called
do_hard_reset(). The existing Intel reset_prepare() gets generalized as
soc_reset_prepare() (and other hooks for arch, mainboard, etc. can now
easily be added later if necessary). We will also use this central point
to ensure all platforms flush their cache before reset, which is
generally useful for all cases where we're trying to persist information
in RAM across reboots (like the new persistent CBMEM console does).
Also remove cpu_reset() completely since it's not used anywhere and
doesn't seem very useful compared to the others.
Change-Id: I41b89ce4a923102f0748922496e1dd9bce8a610f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19789
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Since this mainboard provides 3 COM ports on LPC, enable decoding of the
corresponding address range for COM 3.
Change-Id: I15c0748fce67eef46401c314f441aa45f5e3c5fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
- use Siemens NC FPGA driver for backlight brightness and PWM control
- set Dsave time for board reset after falling edge of signal xdsave
Change-Id: I5077d4af162e54a3993e5e0d784a8356f51bd0c9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I558e6c63caf95ec5279ec5a866b54fb199116469
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Based on the Intel G41 chipset, ICH7 southbridge, and IT8720F Super I/O.
Tested, working:
* Booting Linux 4.11.3 and Windows 8.1 from USB and HDD
* Resume from S3 (Linux and Windows)
* Native raminit (DDR2-800)
* Native graphics init (SeaBIOS, Linux)
* Graphics init with VGA BIOS (SeaBIOS, Windows)
* PCI-E x16 PEG slot, PCI-E x1 slot from southbridge
* Realtek ALC888 HD Audio (including front panel and jack detection)
* Realtek R8168 Gigabit LAN
* Both SATA ports
* USB 1.1 and 2.0 devices (keyboard, mass storage)
* PC speaker beep
* COM header
* Super I/O Environment controller (temps, voltage, fans)
* PS/2 keyboard and mouse
* Flashing with `flashrom -p internal`
* 1MiB and 2MiB SPI flash chips
* CMOS gfx_uma_size
Appears, OS driver loads, but otherwise untested:
* IrDA header
* CIR header
* TPM header
Untested:
* S/PDIF digital audio
Tested, known broken:
* CMOS power_on_after_fail
* USB keyboard in secondary payloads
Change-Id: Ifc4c8935b1a11e55f4bf6cfa484a8a8d09b1adda
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20027
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
I updated my spike patch[1] to cleanly apply to current spike master.
As a side effect, the UART is now at 0x02100000.
[1]: https://github.com/riscv/riscv-isa-sim/pull/53
Change-Id: I4cb09014619e230011486fa57636abe183baa4be
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/20126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
For an unknown reason, the I2C ACPI devices were placed
under \SB intead of \SB.PCI0, as with all other non-Atom
based Intel platforms. While Linux is tolerant of this,
Windows is not. Correct by moving I2C ACPI devices where
they belong.
Also, adjust I2C devices at board level for google/rambi
as to not break compilation.
Change-Id: I4ef978214aa36078dc04ee1c73b3e2b4bb22f692
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20056
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The supported "G41C-GS" with a nuvoton nct6776 superio is actually
G41C-GS R2.0, which is different with the more easily-found revision
G41C-GS (R1.0) with Winbond W83627DHG superio, and should be ported
separately.
Photos for the two revision:
R1.0: https://web.archive.org/web/20160915160553/http://www.asrock.com/mb/photo/G41C-GS(L1).jpg
R2.0: https://web.archive.org/web/20160717203810/http://www.asrock.com/mb/photo/G41C-GS%20R2.0(L2).jpg
Change-Id: If60a694bcf0652ab32c0ac75ceec7e27e11fe9eb
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/19980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Update devicetree PCI config based on board spec:
- enable PCIe Root Ports 5 and 9 (wifi and nvme respectively)
- enable PCIe CLKREQ on RP9, disable on RP5
- enable USB OTG
- enable P2SB
Note: PCIe RP5 is on 0.1c.0 despite this being labeled as RP1
Change-Id: Ia71ed25bd41668df1ee3e4b4e28f54482722452c
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Needed for UEFI booting via Tianocore;
with PM timer disabled, payload hangs.
Change-Id: I6c65cb9d3e6a10baea4cc1e2d9e94c36fe419561
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ib63e5e8a1bcbc25c288dec7d1ef6c06239ada34b
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The FSP Temp RAM init will fail if the mircocode values are set
to 0. A valid microcode update needs to be included and its size
and offset need to be set in the config.
Change-Id: I26d05bd7b37c8d91bf34f399c7c4189f9d3dd34a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19936
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Adding code to setup the spd information from sodimm.
Adapted from intel/kblrvp.
Change-Id: I0403f999dac1bdef0e9e1abe7c9c62407e223bb1
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The GPIO configuration matches the one from the original BIOS.
Some configs don't make much sense, but I kept it as is so it
would match (such as a NC pin with TX set to 1, or RXINV enabled).
Remove unnecessary early GPIO config.
Change-Id: Iaec8630cef9a523fb2e2503143aa4aa72fbedc1f
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19934
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Like other devices using ENE embedded controllers, the librem13v2
requires this config option for the PS2 keyboard and mouse
(trackpad) to function properly.
Change-Id: Ifba13b93a1fe2e76b2790d1c273fd9e2b5368ab0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add the initial directory for the port of the Librem 13 v2.
The base implementation was copied from the google/chell directory
and the chell references were replaced. spd directory was removed
since the RAM is not soldered on the MB. The Kconfig, board_info.txt
and devicetree.cb files were modified to match the Librem 13 v2
hardware information. The romstage.c, mainboard.c, Makefile.in and
dsdt.asl were modified to remove chromeos specific code. The boardid.c,
chromeos.c, chromeos.fmd, cmos.layout, ec.c, ec.h and smihandler.c
files were removed from the tree, and the acpi directory was replaced
with the acpi directory from the purism/librem13 board.
These changes allow us to remove the references to chromeos specific
code and allow coreboot to compile when the librem13v2 board is selected.
Change-Id: I24263fde18fcea70163dbdc59df6ea1d98c97af8
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The FADT revision was set to 5, but we do not implement the
ACPI v5.0 specification, which prevents Windows from booting.
Setting it to v3 (matching most other boards) fixes the issue
and Windows now boots normally.
Bug found by Matt DeVillier, fix tested by Youness Alaoui on
Librem 13 v1 hardware.
Please also see commits 00d250e2289de (intel/skylake: Switch FADT
to ACPI version 3.0) [1] and 27e6042bb7d0b1 (intel/apollolake:
Switch FADT to ACPI version 3.0) [2].
[1] https://review.coreboot.org/19453
[2] https://review.coreboot.org/19146
Change-Id: Ide97cbf64f7b05018433436431ab4723b217fe22
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
A simple rename of the directory and the config values
and string in Kconfig/Kconfig.name/board_info.txt
It will be less confusing for users since the first models
are referred to as 'v1' everywhere now.
Change-Id: I23fa977717230c2001868741bb684e9633a2c0bb
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19931
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
For an unknown reason, the I2C ACPI devices were placed
under \SB intead of \SB.PCI0, as with all other non-Atom
based Intel platforms. While Linux is tolerant of this,
Windows is not. Correct by moving I2C ACPI devices where
they belong.
Also, adjust I2C devices at board level for intel/strago
and google/cyan as to not break compilation.
Change-Id: Iaf8211bd86d6261ee8c4d9c4262338f7fe19ef43
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20055
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Change-Id: Ie0b64eadc634049f6b65cf555407337fb7c4363c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Switch from lapic to tsc.
Allows timestamps to be used in coreboot, as there's a reference
clock available to calculate correct time units.
Clean Kconfig, remove duplicated lapic code and include tsc dir for
LGA1155 boards.
Tested on Lenovo T430.
Change-Id: I849ca2b3908116d9d22907039cd6e4464444b1d1
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update user facing camera i2c address to 0x36.
BUG=None
TEST=Build & boot on soraka. Make sure user facing camera is detected.
Change-Id: I4645ae5734faef4b6a821c04ab817a7b99da6e4b
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
|
|
The new config choice is called RUN_FSP_GOP. Some things had to happen
on the road:
* Drop confusing config GOP_SUPPORT,
* Add HAVE_FSP_GOP to chipsets that support it,
* Make running the GOP an option for FSP2.0 by returning 0
in random VBT getters.
Change-Id: I92f88424004a4c0abf1f39cc02e2a146bddbcedf
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Provide all gfx init methods as a Kconfig `choice`. This elimates the
option to select native gfx init along with running a Video BIOS. It's
been only theoretically useful in one corner case: Hybrid graphics
where only one controller is supported by native gfx init. Though I
suppose in that case it's fair to assume that one would use SeaBIOS to
run the VBIOS.
For the case that we want the payload to initialize graphics or no
pre-boot graphics at all, the new symbol NO_GFX_INIT was added to the
choice. If multiple options are available, the default is chosen as
follows:
* NO_GFX_INIT, if we add a Video BIOS and the payload is SeaBIOS,
* VGA_ROM_RUN, if we add a Video BIOS and the payload is not SeaBIOS,
* NATIVE_VGA_INIT, if we don't add a Video BIOS.
As a side effect, libgfxinit is now an independent choice.
Change-Id: I06bc65ecf3724f299f59888a97219fdbd3d2d08b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
MAINBOARD_FORCE_NATIVE_VGA_INIT is to be selected instead of the user
option MAINBOARD_DO_NATIVE_VGA_INIT. The distinction is necessary to
use the latter in a choice.
Change-Id: I689aa5cadea9e1091180fd38b1dc093c6938d69c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add support for ELAN 5515 device.
BUG=b:62331218
Change-Id: Id91a41743330c9e356293cfda7b2e3743dcd480c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20040
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The word 'coreboot' should always be written in lowercase, even at the
start of a sentence.
Change-Id: I7945ddb988262e7483da4e623cedf972380e65a2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The coreboot sites support HTTPS, and requests over HTTP with SSL are
also redirected. So use the more secure URLs, which also saves a
request most of the times, as nothing needs to be redirected.
Run the command below to replace all occurences.
```
$ git grep -l -E 'http://(www.|review.|)coreboot.org'
| xargs sed -i 's,http://\(.*\)coreboot.org,https://\1coreboot.org,g'
```
Change-Id: If53f8b66f1ac72fb1a38fa392b26eade9963c369
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/20034
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Wrapping the long line tries to address a warning by `checkpatch.pl`,
but the line is still over 80 characters long.
Change-Id: Ib75d4da1880624eb83f7a419cb6762f1c4c2a7b2
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/20033
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The comma-separated PCI vendor and device ID is used to associate the
VGA BIOS to the video device by using it as the file name of the VGA
Option ROM.
Change-Id: I755554eeb9a560d034d6e8fe49de619d800ea045
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/18741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Changes the offsets of some options so that options that span multiple
bytes are byte aligned.
To make the cmos.layout file more consistent some things where moved
around in the cmos.layout of thinkpads X200 and T400.
Change-Id: Ic84a2a5dc6f9c102f041085871c2ed55e2f3692a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
A new variant copied from reef.
Allow override of the SKU.
Change-Id: Ibe160e75aa23623812f0fb9121d1d8226afc00d8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20020
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each rambi variant has a different USB port config.
Port data currently available for only candy and squawks;
other variants to be added once data obtained.
Change-Id: If7ce3d135d6ffe53ab1566d5258d01b052ac47f4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each jecht variant has a different USB port config.
Change-Id: I3b15aac9c4971e2ae230106016fba3a583ec6c9a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19971
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
