| Age | Commit message (Collapse) | Author |
|---|
|
Add SPD support to lantis for MT53E512M32D1NP-046 WT:B
BUG=None
BRANCH=firmware-dedede-13606.B
TEST=FW_NAME=lantis emerge-dedede coreboot chromeos-bootimage
Change-Id: I22c50a55dd3b8bbda64ba1b607c8b22cc6592f98
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
irq(ACPI_IRQ_LEVEL_LOW) -> ACPI_DESCRIPTOR_INTERRUPT -> IO-APIC,
will assert interrupt frequently;
irq_gpio(ACPI_GPIO_IRQ_EDGE_BOTH) -> ACPI_DESCRIPTOR_GPIO -> INT34C8;
will not assert interrupt frequently;
Because IRQ configuration can't be setted to both EDGE trigger.
BUG=b:195635555
BRANCH=dedede
TEST=Cirrus audio codec PLT pass
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I65bca519f75af84848284f039b6ad67cb1887823
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56973
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
"Latched" GPIOs like this one are a virtual representation of the
pending interrupt flag for the edge-triggered pin and not a direct
representation of line state, so they should always be marked
ACTIVE_HIGH or depthcharge will incorrectly negate them. This has always
been wrong and meant that depthcharge doesn't correctly wait for Cr50
flow control responses on these platforms. Thankfully it doesn't seem
like we've seen any practical issues from this, but it's still very
wrong.
BRANCH=trogdor
BUG=none
TEST=Booted CoachZ (no visible difference)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie1586b0e10b64df0712e28552411c4d540a7e457
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
|
|
Setting the clock source depends on clock request pin for WLAN/SD/SSD device. Also turn off the unused (4/5/6) clock sources.
In guybrush, clock source 0/1/2/3 are routed for WLAN/SD/WWAN/SSD device.
BUG=b:186384256
BRANCH=none
TEST=Verify the config setting can update to the GPPCLKCONTROL registers.
Signed-off-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Change-Id: I240543e92cbc178cee034c37d7c26da0a6bbb7f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56895
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For mainboard devicetree, it always have definition for enabling
cpu_cluster 0 which is required for all the variants.
Since it is SoC related settings, it's better to keep in chipset.cb
as a common setting for all the mainboards using the same SoC.
BUG=None
BRANCH=None
TEST=Change has no functional impact on the brya board.
Change-Id: I20bf1a87c7a9b343a86053692617c127a1a3250d
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56955
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
coreboot always assumes that BSP APIC ID will be 0 and core enumeration
logic will look for lapic id from the mainboard.
As per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, this assumption might
not hold true and we may have any other core as BSP. To handle this,
we need to remove hardcoding of APIC ID 0 from mainboard.
BUG=None
BRANCH=None
TEST=Check if there is no functional impact on the board.
Change-Id: I175ae26f934f08e125bea7cc3195bdb5792c2360
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56954
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Kconfig options and enable TPM device in devicetree
BUG=None
TEST=Booted the image and checked the successful TPM
communication in verstage,romstage & ramstage from
coreboot logs.
Signed-off-by: Thejaswani Puta thejaswani.putta@intel.com <thejaswani.putta@intel.com>
Change-Id: Icaedf9f17e35e82c35cbabd6d2938c167e42e9e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
Create the driblee variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:191732473
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_DRIBLEE
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I1ad9a4e0cf7999337b55d62d5cc94e4f6c2e98f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Create the corori variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:194356176
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_CORORI
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I8380d5aab61c99d545625789ff1251ec1caa84a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56796
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All Atlas devices have the touchscreen controller, so probing for its
presence is unnecessary. Removing the probe requirement allows the
touchscreen ACPI device in Linux to re-enumerate when rebinding its
I2C adapter device.
Without this change, after rebinding the touchscreen's I2C adapter
device using sysfs the touchscreen ACPI and HID devices are absent, and
the touchscreen is unresponsive.
With this change, the touchscreen ACPI and HID devices are re-created
after rebinding its I2C adapter device, and the touchscreen becomes
responsive again.
BUG=b:177350937
TEST=Tested on 2 Atlas DUTs running Chrome OS R94 top-of-tree builds
with Linux 4.4 and 5.4.
Built new AP FW from Atlas Chrome OS firmware branch with this change
applied. Tested shipping RO + new RW, and new RO + new RW.
Test sequence:
1) Boot DUT, verify basic touchscreen functionality.
2) $ cd /sys/bus/platform/drivers/i2c_designware
3) $ ls -ld i2c_designware.0{,/i2c-6{,/i2c-ACPI0C50:00{,/0018:0483:1058.*{,/hidraw{,/hidraw*}}}}}
lrwxrwxrwx. 1 root root 0 Aug 12 01:07 i2c_designware.0 -> ../../../../devices/pci0000:00/0000:00:15.0/i2c_designware.0
drwxr-xr-x. 5 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6
drwxr-xr-x. 4 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00
drwxr-xr-x. 5 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0002
drwxr-xr-x. 3 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0002/hidraw
drwxr-xr-x. 3 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0002/hidraw/hidraw1
4) $ echo i2c_designware.0 > unbind
5) Verify touchscreen is unresponsive (as expected after unbind).
6) $ ls -ld i2c_designware.0
ls: cannot access 'i2c_designware.0': No such file or directory
7) $ echo i2c_designware.0 > bind
*** Without this change: ***
8) Touchscreen remains unresponsive.
9) $ ls -ld i2c_designware.0{,/i2c-6{,/i2c-ACPI0C50:00}}
ls: cannot access 'i2c_designware.0/i2c-6/i2c-ACPI0C50:00': No such file or directory
lrwxrwxrwx. 1 root root 0 Aug 12 01:18 i2c_designware.0 -> ../../../../devices/pci0000:00/0000:00:15.0/i2c_designware.0
drwxr-xr-x. 4 root root 0 Aug 12 01:18 i2c_designware.0/i2c-6
*** With this change: ***
8) Touchscreen is functional again.
9) $ ls -ld i2c_designware.0{,/i2c-6{,/i2c-ACPI0C50:00{,/0018:0483:1058.*{,/hidraw{,/hidraw*}}}}}
lrwxrwxrwx. 1 root root 0 Aug 12 01:09 i2c_designware.0 -> ../../../../devices/pci0000:00/0000:00:15.0/i2c_designware.0
drwxr-xr-x. 5 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6
drwxr-xr-x. 4 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00
drwxr-xr-x. 5 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0003
drwxr-xr-x. 3 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0003/hidraw
drwxr-xr-x. 3 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0003/hidraw/hidraw1
Signed-off-by: Matthew Blecker <matthewb@chromium.org>
Change-Id: I7b90690b0591e8748d7a007f8cc9688d393e59db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56928
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add supported memory parts in mem_parts_used.txt, and generate
SPD id for these parts.
MT53E512M32D1NP-046 WT:B
MT53E1G32D2NP-046 WT:B
BUG=b:192052098
TEST=FW_NAME=redrix emerge-brya coreboot
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I61377e6cdd3af9d6d80b9e1e68191b39f43358ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add I2C parameters to make sure each bus speed is around 390kHz.
BUG=b:188793264
TEST=Measure by scope.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib47228b8684c44f6acfec9e9e4b6e7b18ba6f6c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update initial gpio configuration for kano
BUG=b:192370253
TEST=FW_NAME=kano emerge-brya coreboot
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I4d6099fa8d17bebf798ddf236a68886087e2a95e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Recent change "7a8c68a: mb/google/brya: Configure H21 as GPO and A17
as low" turned EN_FCAM_PWR low since EN_FCAM_PWR is turned ON and
OFF by IPU driver while MIPI UFC probing. However USB UFC also
requires 3.3V which is enabled by A17. This caused USB UFC
enumeration to fail
BUG=b:196014678
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I88c204ec07b1f7511f0d88074e336cfc9116a7d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56882
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
modify reset_gpio as active low to meet touchscreen spec
BUG=b:195490284
BRANCH=none
TEST=build coreboot and touchscreen works
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I7ce1b3025db8abebf5693b34da846a7e969246fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable MKBP (Matrix Keyboard Protocol) interface for all Brya family
to use for buttons and switches. Disable TBMC (Tablet Mode Switch
device), as it is not needed anymore.
BUG=b:170966461
TEST=manual test on Brya P1: Volume Up/Down buttons
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: Ic9c707f57871f388c363e01c9ab78a3b358ce728
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add mainboard finalize and shutdown call to match zork.
Deassert EN_PWR_FP in bootblock, power up correctly in finalize.
| Phase | SOC_FP_RST_L | EN_PWR_FP | S3 resume |
|-----------|--------------|-----------|----------------------|
| Bootblock | **Low** | **Low** | Maintain High / High |
| Romstage | Low | Low | Maintain High / High |
| Ramstage | Low | **High** | Maintain High / High |
| Finalize | **High** | High | |
| Shutdown | **Low** | **Low** | |
BUG=b:191694480
TEST=Build, verify GPIO configuration.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Iaae5feec60abb2480777d1f99174254c5132bb43
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Set PL4 value dynamically for brya board based on CPU SKUs
which is detectable at runtime.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 with below messages,
On brya (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (39000, 39000) PL4 (100000)
On brya (482):
Overriding DPTF power limits PL1 (4000, 28000) PL2 (43000, 43000) PL4 (105000)
Change-Id: I20b98ccd8493ed238de647cda8ceb25f62029133
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Lockdown configuration is done in their baseboards. Thus, remove the
setting from the variants overridetree.
Change-Id: Iadb1201718466503987e4f6bd72bf711a2d3128e
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Create the nipperkin variant of the guybrush reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=None
BRANCH=None
TEST=util/abuild/abuild -p none -t google/guybrush -x -a
make sure the build includes GOOGLE_NIPPERKIN
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ie525ea501e6c3d5d94e67c1db1d4e307fb7ccba7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56921
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add PL4 values for brya0 board for different CPU SKUs.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 with below messages,
On brya (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (39000, 39000) PL4 (100000)
On brya (482):
Overriding DPTF power limits PL1 (4000, 28000) PL2 (43000, 43000) PL4 (105000)
Change-Id: I095e9eda6665fd1927f35ee57d52922eddd8227a
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Tune the USB phy settings to update TXVREFTUNE0/COMPDISTUNE0 to
higher value for USB port 5 (Type-A).
BUG=b:194053549
TEST= Pass USB 2.0 SI Eye diagram measurement.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Id1ede34bdbee0c1f9f7d10fc7ffbc9648af31e3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56925
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DDR5 Maple Ridge SKU (Board ID 0x16) uses a Memory down DIMM
configuration.
TEST=Boot DDR5 MR SKU to OS.
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I0b7a96b5534d8b80776aa7578ce7c13181af7882
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56881
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Naming spd_info struct based on memory topology helps in reuse of
code.
lp4_lp5_spd_info -> memory_down_spd_info
ddr4_ddr5_spd_info -> dimm_module_spd_info
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I0b7a66b5524d8b80776ab7578ce7b13181af7882
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Change-Id: I8c5d6686bf7c694f9d594e3801c79cfd7fb3da80
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56342
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable MKBP (Matrix Keyboard Protocol) interface for all dedede family
to use for buttons and switches. Disable TBMC (Tablet Mode Switch
device), as it is not needed anymore.
BUG=b:170966461
TEST=manual test on Madoo:
Volume Up/Down and Power buttons, Tablet Mode switch
Cq-Depend: chromium:3069163
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: I9d1f43e4dd56318af4c1d5f5c1c3a2c237a05c5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56840
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With current setting Display audio codec probe fails.
Hence HDMI/DP audio fails.
Earlier, with FSP 2037 was used the mode was incorrectly programmed to 4T
This setting was carried ahead with below change:
Commit : 50f8b4ebdd7db8077b87ab7686637599c9d93af3
The issue was fixed in later FSPs and with current
FSP v2237, we need to set the TMODE to 8T as per spec.
TEST=Verify HDMI/DP Playback on ADL P RVP
Fixes: 50f8b4ebdd7db8077b87ab7686637599c9d93af3
(soc/intel/alderlake: Add enum for HDA audio configuration)
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Change-Id: Ia39a33f5da2fea0dc2eaf4eae45999a711c61c33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56208
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Balaji Manigandan <balaji.manigandan@intel.com>
Reviewed-by: Meera Ravindranath <meera.ravindranath@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
System76 uses several custom CMOS values downstream. Reduce our diff by
providing a generic layout with the defaults:
boot_option=Fallback
debug_level=Debug
power_on_after_fail=Enable
Tested on galp3-c, gaze15, oryp5, oryp6. All boards boot multiple times
with USE_OPTION_TABLE selected.
Change-Id: Ie57b0e5713bba8ad46e1a4123a3ddd43e0eea964
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add charger current throttling support for galtic
control charger index * 64 = Value mA
32*64=2048
28*64=1792
24*64=1536
20*64=1280
BUG=b:187231627
TEST=Built and tested on boten system
Cq-Depend: chrome-internal:3846209
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I5e1849551ff051bca591f19f9e40da4c89ab74e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Yang <paul.f.yang@intel.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Haboki is project which use discrete TPM, so add discrete TPM and
disable cr50 in overrideree.
BUG=b:187094464
TEST=FW_NAME=haboki emerge-keeby coreboot chromeos-bootimage
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I08f2a562c3f62c60402350151ea260b70890a744
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Enable LTE PCIe port according to fw config.
BUG=b:192052098
TEST=emerge-brya coreboot chromeos-bootimage
Change-Id: Ic9472d2249c622858a75c63bc82e8e4e8166a3d7
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56894
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add mipi camera support by selecting the Kconfig symbols and adding it
to the devicetree with ACPI UID 0x50000 and name IPU0.
BUG=b:192052098
TEST=checked mipi camera works
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I69281f36ddbc1abf9905c8db9287500f9aa995c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56893
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
add GPP_D16 in gimle gpio.c and set value to 1 for PP1800 DMIC init sequence
BUG=b:195968649
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ia0639162e2c3f02f622470fa16c21fe8a067cf7c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56889
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New board introduced to trogdor family.
BUG=b:193870279
BRANCH=none
TEST=make
Change-Id: If3d9662e8725e30e1308d77b05545efbee29f846
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56384
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Based on schematic and gpio table of taeko, generate overridetree.cb
settings for taeko.
BUG=b:195494281
TEST=FW_NAME=taeko emerge-brya coreboot chromeos-bootimage
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I96aaf48284a226edc39115f870bf0f3dd83ab8b4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
TSR2 thermal sensor doesn't define in cret. Fix DPTF passive and
critical policies for getting negative temperatures in OS.
BUG=b:195868075
BRANCH=dedede
TEST=Build and boot to OS in cret. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I849662cbb3adc8e528d65af2c90e7c8e4880d607
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add dynamic power limits selection mechanism for aldrvp board.
BUG=None
BRANCH=None
TEST=Build FW and test on adlrvp with DPTF tool
On adlrvp (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (55000, 55000)
On adlrvp (682):
Overriding DPTF power limits PL1 (5000, 45000) PL2 (115000, 115000)
Change-Id: Id1aef0125c6e1e105665172f19bda271e232d94f
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BUG=b:195901486, b:195387997
BRANCH=none
TEST=Check fan is able to control by EC
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: If758d75ff24c88c9eaf0de90ac0ef08d172a2edd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56879
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allows using the internal speakers of the oryp6.
Smart AMP data was collected using a logic analyzer connected to the IC
during system start on proprietary firmware. This data is then used to
generate a C file [1].
[1]: https://github.com/system76/smart-amp
Change-Id: I57781a7223a52b8fc5295cf686412926529c3a7f
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For mainboard devicetree, it always have definition for enabling
cpu_cluster 0 which is required for all the variants.
Since it is SoC related settings, it's better to keep in chipset.cb
as a common setting for all the mainboards using the same SoC.
BUG=None
BRANCH=None
TEST=Change has no functional impact on the brya board.
Change-Id: I8f7c3184b62f8d84ca4605fb9f2a1cc569f1f964
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56853
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
coreboot always assumes that BSP APIC ID will be 0 and core enumeration
logic will look for lapic id from the mainboard.
As per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, this assumption might
not hold true and we may have any other core as BSP. To handle this,
we need to remove hardcoding of APIC ID 0 from mainboard.
BUG=None
BRANCH=None
TEST=Check if there is no functional impact on the board.
Change-Id: Ibc60494b0032a3139c1e6c79251fb2da750c8de8
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
update the DPTF parameters received from the thermal team.
BUG=b:195602767
TEST=emerge-ambassador coreboot
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: I5dc89d1d4c2b64c9aac780a7db743a91fd0ebc9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56819
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jeff Chase <jnchase@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Compatible headphone codec "Realtek ALC5682I-VD" and "cirrus CS42L42"
Compatible AMP codec "ALC1015Q-VB" and "MAX98360"
BUG=b:193373320
BRANCH=dedede
TEST=Both realtek and cirrus audio codec can work normally
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I9121e75eaf46b43e6dc5ef2e31029a153c7a807d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Based on the Taeko's schematic, generate memory settings.
BUG=b:161089195
TEST=FW_NAME=taeko emerge-brya coreboot chromeos-bootimage
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I4e23c28aaf20d9e52b43033b4e41c751e26872bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The TSR1._PSV has been redefined.
It will report errors when disassembling the ACPI tables with the iasl.
It is OK when Removing the TSR1._PSV and adding the TSR0._PSV
BUG=b:194509417
BRANCH=dedede
TEST=The iasl can run on Dut successfully
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I524255c79d3c71573d122944da5058389f79d95d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
This will enable to include multiple VBT binaries in a single image
and load corresponding file according to HW configuration.
BUG=None
TEST= Boot device on LP5/LP4, corresponding VBT file should be loaded.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: Iace0e5e0783b2074393a537da8cc645102d2acda
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55969
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Keep the clock source for PCIe slots as always on. Also turn off the
unused (0/1/5/6) clock sources. Currently bilby only uses clock sources
2, 3 and 4, out of which clock source 3 and 4 are routed for PCIe
external slot. And clock source 2 is routed for M.2 PCIe slot.
TEST:Verify end devices enumerate on D:F 1.1/1.2 RPs over warm reboot.
Signed-off-by: Aamir Bohra <aamirbohra@gmail.com>
Change-Id: Ida485b06279b0a8659c8d00873c3d6023d1e542f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56826
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update initial gpio configuration for taeko
BUG=b:195252436
TEST=FW_NAME=taeko emerge-brya coreboot
Change-Id: Ida1edbf874c93f6efac45c276920ead9311ac6f2
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Set power limits for brya0 variant board based on CPU SKUs
which is detectable at runtime.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 variant board with below messages,
On brya (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (39000, 39000)
On brya (482):
Overriding DPTF power limits PL1 (4000, 28000) PL2 (43000, 43000)
Change-Id: I4c07319af756b10e5d22f320e97ff956fb4a14c6
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56622
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Elan touchscreen and remove Goodix touchscreen. We also get confirmation by Elan that address is 0x15.
BUG=b:195494292
BRANCH=none
TEST=build coreboot and dmesg | grep hid, it showed i2c-ELAN9050:00.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I20a7fd0b370803c14990b77bab302727af197ccb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56801
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add dynamic power limits selection mechanism for brya board based on
CPU SKUs which is detectable at runtime.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya with below messages,
On brya (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (39000, 39000)
On brya (482):
Overriding DPTF power limits PL1 (4000, 28000) PL2 (43000, 43000)
Change-Id: I86619516adeec13642f02ba7faf9fc4945ad774e
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The board uses the default size specified in the SoC.
Change-Id: Ie71a0fea1ff9de6c4f1ce8db2db09bb3cd35d04d
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
coreboot always assumes that BSP APIC ID will be 0 and core enumeration
logic will look for lapic id from the mainboard.
As per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, this assumption might
not hold true and we may have any other core as BSP. To handle this,
we need to remove hardcoding of APIC ID 0 from mainboard.
BUG=None
BRANCH=None
TEST=Check if there is no functional impact on the board.
Change-Id: I726d70b4ffc35a28a654abbd20c866f1410e1aee
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Raise little CPU to 2GHz at romstage to improve boot time by about
100 ms.
BUG=b:195274787
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Id6aac8f9db86a6c1e61ea94863f2cbde12c0482e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Some eMMCs need 80+ms for CMD1 to complete. And the payload may need to
access eMMC in the very early stage (for example, Depthcharge needs it
20ms after started) so we have to start initialization in coreboot.
BUG=b:195274787
TEST=emerge-cherry coreboot
BRANCH=cherry
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: Idc86f9121fa4a34f09a683f7a81087c13ea3dd42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56842
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Select mmc storage config for cherry.
BUG=b:195274787
TEST=emerge-cherry coreboot
BRANCH=cherry
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: I67c8795b6e6fc121e8fe61c40da05593faa02d94
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56841
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Lulu is the only variant that does not disable channel 1 in pei_data
when the SPD index indicates it is unused. For consistency with the
other variants that use SPD files, disable channel 1 explicitly.
Change-Id: I8c613c5d90075495d2f76d33abf15d74ac63c125
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55802
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add camera support in devicetree and associated GPIO configuration.
BUG=b:193397569
BRANCH=dedede
TEST=Camera function is OK
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I3275ab408f6a03735a35eaa8025c36df09c9898c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Tested on prodrive/hermes.
Change-Id: I72be8bde59d9eb0c1eff8c65dc734c6805732e09
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56086
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: <wouter.eckhardt@prodrive-technologies.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This feature was added in ADL-M RVP for discovering correct
audio topology using OEM string e.g., "ADL_MAX98373_ALC5682I_I2S"
for discovering boards having audio expansion card
Bug=None
Test= With CBI FW_CONFIG set to 0x100
localhost /home/root # dmidecode -t 11
Getting SMBIOS data from sysfs.
SMBIOS 3.0 present.
Handle 0x0009, DMI type 11, 5 bytes
OEM Strings
String 1: ADL_MAX98373_ALC5682I_I2S
Change-Id: I05887d9d654eae6d9d2da731d8ab4cf4a05c287f
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55368
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I80f11b8f0c2a1fdccbc322c3c4783c61684ff37a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55634
Reviewed-by: Selma Bensaid <selma.bensaid@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Gimble don't have retimer on port0, the port need to be configured for the SOC to handle Aux orientation flipping.
Also add "typec_aux_bias_pads" lets the SoC IOM firmware control the Aux DC bias voltages.
BUG=b:195087071
BRANCH=none
TEST=check both orientation can output display on type-c monitor.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I057048c14110bb81bf5b5fd0e3151deb031ca5d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable IOMMU PCIe device.
BUG=b:194173037
TEST=lspci shows IOMMU device
00:00.2 IOMMU: Advanced Micro Devices, Inc. [AMD] Device 1631
Cq-Depend: chrome-internal:4027293,4027294
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Change-Id: Ia84276ca98163158d818a0efc3e021b93ab365de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Create the bugzzy variant of the waddledoo reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:192521391
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_BUGZZY
Signed-off-by: Raymond Chung <raymondchung@ami.corp-partner.google.com>
Change-Id: I851b9a75c387586d2fb84b762788e962f33472b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56762
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:187969783
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I1e063524cfa4121c38cfed23e95557953511d884
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BUG=b:195378817
BRANCH=none
TEST=Check fan is able to control by EC
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I84c020e470194072bb796f75f8a1304832504469
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56768
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The all shipped magolor and maglia has SSFC= 0x840.
The value is defined as 5M MIPI camera.But the value:0x840 will
conflict with the updated touchscreen field.
It will cause some touchscreen no function if make auto-update new
firmware.The CL would correct the field error.
The original fields:
CAMERA_WFC 38 40
TS_SOURCE 41 44
Correct fields:
MIPI Cam
CAMERA_WFC 38 40
CAMERA_UFC 41 42
CAMERA_VCM 43 44
Touch-screen
TS_SOURCE 45 48
The SSFC value of Magolor:
CAMERA_OVTI5675 5M AF (SSFC = 0x840)
CAMERA_OVTI8856 8M AF (SSFC = 0x880)
BUG=b:194639170
TEST=Build firmware and verify on camera and touch-screen devices
Change-Id: I13d76ce8b932f483e20ca5388f1c67eb39ba12a1
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56685
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DDI 0/1 ports are shared for DP and HDMI. This implementation
adds support for HDMI display when HDMI is set as connector type
in ddi descriptors.
TEST=verify display over HDMI(0 and 1) in OS.
Signed-off-by: Aamir Bohra <aamirbohra@gmail.com>
Change-Id: I9697211c556f12d1fc0d49418b227fbe6b342673
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
According to the schematic diagram of proto, added drivers/i2c/max98390 to device ref i2c0 and deleted device ref hda.
BUG=b:191811888
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I0f0a8c84db3fbc963797d11246c5d31b395bb744
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56757
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
DP2 and DP2 is muxed with USBC port. This implementation
configures mux for DP functioanlity.
TEST=Verify display over DP2 and DP3.
Signed-off-by: Aamir Bohra <aamirbohra@gmail.com>
Change-Id: If0c8dfbb47175789bb27d4506c1e8b45c425c76a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: ritul guru <ritul.bits@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enable the PCIe RTD3 driver for WWAN device attached to PCIe Root
Port 6 and provide the reset GPIO / src clk pins.
BUG=None
BRANCH=None
TEST=Build and boot the coreboot image, check if device is enumerated
in the lspci list after warm/cold reboot cycles, run suspend cycles and
check if WWAN is entering L2 LPM.
Signed-off-by: Thejaswani Putta <thejaswani.putta@intel.com>
Change-Id: Ie9d1ce55cc1297ea0e1069979bbecfaac8f8de05
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
- configure TROGDOR_HAS_MIPI_PANEL to "n" by default, it can be updated for mipi panels.
- add simple rm69299 panel as an example to append new mipi panels.
- use existing edid struct to update mipi panel parameters.
- add dsi command tx interface for mipi panel on commands.
Change-Id: Id698265a4e2399ad1c26e026e9a5f8ecd305467f
Signed-off-by: Vinod Polimera <vpolimer@codeaurora.org>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52662
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:195274799
TEST=USE="project_primus" emerge-brya coreboot and verify it builds
without error.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I4abf7b2d98b188735ef79f8ffbee4c02099ec021
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56583
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch initiates the brask setting which includes
the gpio and device tree setting.
BUG=b:191472401
BRANCH=None
TEST=build pass
Change-Id: I1bb42c7bb2492402de0810bc4ab2e8d8c0e2392b
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This reverts commit f29437862269de24f85392d49f6afa6fa60ac43e.
Reason for revert: It makes cret can't boot to os without depthcharge change. The depthcharge change related with fw_config and will effect other variants.
BUG=b:194961854
TEST=Build and boot to OS.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I929369c9419375e74be61a4ff3e5566b0f41ce65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Crashlog is a debug feature and not used in normal mode of operation.
Disabling this feature will allow us to disable unused IPs and also
provide boot time savings of ~5-7 ms.
BUG=b:195327879
BRANCH=None
TEST=Platform boots and no function impact
Change-Id: I1f7def4ea41ff7a566aada080be1e791c11766e6
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56654
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the felwinter variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:194431541
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_FELWINTER
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: Iff2b9daec40995a013f9fe0dd76ad667d1807d1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56765
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Init basic override devicetree based on schematics
BUG=b:192052098
TEST=FW_NAME=redrix emerge-brya coreboot chromeos-bootimage
Change-Id: I9fb752fe8280893b84c172d8a519578fa4220184
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Change TypeC port1 usb3 port="3".
BUG=b:194472269
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: Iaba27aad2adfb0a9e83058ac756ca46a762107bc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56545
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some legacy devices need to have the master bit set in the PCI config
due to old drivers not setting it correctly. Set the master bit if the
feature is enabled via Kconfig switch PCI_ALLOW_BUS_MASTER_ANY_DEVICE.
For now, the PCI devices with the ID 110a:403e and 110a:403f needs this
master bit to be set.
Change-Id: Id3f6bda97e5f47d0613a1db8f8adac0b158ab8b1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56632
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Boards based on mc_ehl have, just like some mc_apl variants, legacy
devices on the PCI bus which take longer to boot. In order to ensure
that they will be enumerated correctly wait for them to come up before
PCI scan starts.
TEST=Checked that the new message is visible in the log.
Change-Id: If2f935b69ddaa9364566deacfada5e7d41fcdabd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56631
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new board 'pico' and set correct ram_id offset.
BUG=b:194985056
TEST=None
BRANCH=kukui
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Change-Id: I33c37d99fa0451239bc6626e71bfddb29a11e97b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56691
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
1. Replace OV5675 ACPI entries with IMX208
2. Replace FW_CONFIG name
3. Add support for NVM inside UFC
BUG=b:190674542
TEST=Build and boot to OS on Brya, raw capture on UFC
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I6a3bf13ec844fb46e11ce58382057fcc7187c135
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
As per the schematics, UFC has on card oscillator so we donot need
H21 in NF1 that is IMGCLKOUT
H21 is used to enable this oscialltor so configuring it as 1
A17 is configured as high while _ON method is called by driver and
it is configured as low when _OFF method is called by driver.
Hence coreboot should configure it as low on boot.
BUG=b:190674542
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I745169a5ab6a9c20b6e1bda792a43193d04ac48d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56655
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The cappy2 removed the anpec apw8738bqbi and "disable_external_bypass_vr" should be set to "1" to disable
BUG=b:194146867
BRANCH=dedede
TEST=VCCIN_AUX is disable
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: Ieb4182a989459db629e3b69757c293ca26e8b0cd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
|
|
Using Tpm2.0 device instead of the Cr50 in cappy2
BUG=b:191743435
BRANCH=dedede
TEST=tpm2.0 device function is ok
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I216ceb6386ad57c9f1982187a4525d89869fa9c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56658
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
LTE module L850-GL may encounter U3 wakeup race condition with the host.
Setting xHCI LFPS periodic sampling off time to 0ms so that the host would not
miss the device-initiated U3 wakeup thus avoid the race condition.
BUG=b:187801363
BRANCH=dedede
TEST=flash the image to the device. Run following command to check the bits[7:4] is 0x0:
iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: stanley.wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I9328e758ed92389e44b25ff4daf6ec19b37ae7d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56689
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Ben Kao <ben.kao@intel.corp-partner.google.com>
|
|
WWAN (fibocom L850-GL) works in USB mode, so turn off PCIe 6.
BUG=b:194861116
Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: Ie04a5bb2af9ce11f57339f460a7f880bfc14b688
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add tp and audio devices support in devicetree.
BUG=b:193099842
BRANCH=dedede
TEST=i2c devices function is OK
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I995e93b5a4c4294d6f6b97c48d14fabf48004d92
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56513
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to support different baseboard configuration, we
add the BASEBOARD_DIR to switch the directory. The expected
structure looks like:
mb
..|_ google
.........|_ brya
.............. |_ variants
.....................|_ baseboard
..............................|_ brya
....................................|_ gpio.c
....................................|_ memory.c
....................................|_ devicetree
..............................|_ brask
....................................|_ gpio.c
....................................|_ memory.c
....................................|_ devicetree
......................|_ brya_variant1
......................|_ brya_variant2
......................|_ ...
......................|_ brask_variant1
......................|_ brask_variant2
......................|_ ...
...............|_ <all mb common code>
BUG=b:191472401
BRANCH=None
TEST=build pass
Change-Id: Ic99e42dbbd27fa3e1f6cb3a1b5daee1c8c7b1083
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Realtek speaker amplifiers under auto mode operation have Absolute Max
Rating (AMR) at 1.98 V. Hence probe the firmware config for speaker
amplifier and program the VCCIOSEL accordingly.
BUG=b:194120188
TEST=Build and boot to OS in Storo. Ensure that the VCCIO selection is
configured as expected and probing the GPIO reads the configured
voltage.
Change-Id: Ibd3bc90bd0bbc9a35922b29e3d1e106321bc7a06
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56616
Reviewed-by: Evan Green <evgreen@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Latency Tolerance Reporting is yet another PCIe power management feature
which can have a bad influence on realtime performance. Disable this
feature for all PCIe root ports.
Change-Id: I38023e095ca55efd2178ad944f651fee1f1c34cd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
L1 substates of a PCIe link are meant to save some power when the link
is not active but have the drawback that the PCIe latency is increased
as PLLs are switched on and off as needed.
In order to get a better realtime performance, disable all substates for
every PCIe root port.
Change-Id: Ic5bc8410709d0f0094810bc11a7723e88c30e397
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This variant uses I210 MACPHYs so enable the I210 driver in order to set
the needed MAC addresses. In addition add the function to retrieve a
valid MAC address for the given MACPHY.
Change-Id: Id1d59349db1b86cfdd71bbe27577c0530e8f0b51
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56567
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All the boards based on the mc_ehl baseboard have the NC-FPGA available.
Enable the appropriate driver on baseboard level.
Change-Id: I40b76a837b7ddb70ceba3135996b1c1080170c4d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56566
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All variants based on mc_ehl will use the Siemens HWILIB. Select the
Kconfig switch on baseboard level.
Change-Id: I940f84a4a7449487fe78c793f8dbb1c1b49fa54b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56565
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable IBECC for mc_ehl1 to provide a memory failure protection.
Change-Id: If8f81d6bacb77dc38e231c1cedf22831de8a38a9
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56564
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In favor of better realtime performance disable dynamic frequency
support in the System Agent for mc_ehl1.
Change-Id: I0e62bcf2e5efa97d89bf7192f1536747a02ad992
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56563
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable measured boot for all boards based on mc_ehl baseboard.
Change-Id: I3aff943305c024d1f25d2127e6f60495828da3eb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
All the boards based on the mc_ehl baseboard have a TPM which is
connected to SPI but mapped into the address space of the x86 so that
it acts like a LPC attached TPM. Enable the TPM driver so that it will
be used. In addition add the needed entry in devicetree.
Change-Id: I301d0ed4a108bac45d95eced120e7ba280945d9c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
