| Age | Commit message (Collapse) | Author |
|---|
|
Configure I2C bus 5 high and low time for p-sensor device.
BUG=b:181727056
TEST=Measured the I2C bus frequency reduce to 387 KHz.
Change-Id: I4b6d78d84b8ea145093f52bbb13684e2c6aa979c
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Function is identical for all mainboards, so factor it out.
Change-Id: Ibe08fa7ae19bfc238d09158309f0a9fdb31ad21c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50028
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I55815a824ea3a77e6e603ba4beb17457f37c48f5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch adds the changes to enable the TCSS.
BUG=b:175808146
TEST= Boot shadowmountain board, Test the functionality of the Type-C
ports on both the mainboard and daughterboard by plugging in the Type-C
devices and verified the devices are detected via EC console and in the
OS.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: Ieaf1170ca718a14d24b773a4a85516e0bbfbb569
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51026
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
P-sensor vendor fine-tune detect distance as 20mm for WWAN SAR table switch.
BUG=b:179000150
BRANCH=dedede
TEST=run "i2cdump -y -f 15 0x28" to confirm registers as expected.
un-approach：
=> register address: 0x01 value: 0x00
approach:
=> register address: 0x01 value: 0x02
Confirm WWAN SAR table work as expected.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I659721e60aa0766ed4c277dae43ded222e18ad1c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51343
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mainboard uses a Comet Lake SoC and mixed-topology DDR4 memory.
Drop LPDDR-specific DQ and DQS mappings and comment about Cannon Lake.
Change-Id: Icb986d1c074e64b3cfad3897b69d35d108f64bff
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ie3a3bb7526d734ae1936b8c4db43543b1174829d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I554e7193494a4bbf005aaf2fb4efd6ded383fe07
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51369
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia03169c524dd12b8e7803ea8039c0e98a2b069e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I623fd052404a08cf0adb471bb654622960f1aa62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I45dcaa8b430721f864d4e5d78ae60883175085c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I7de5e4a4d2273d0ea5a84210ea0ce28d312eaa95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:180529005
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I94d97a38d992f46b32c2c6aca4c8da688d3b76fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51257
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:180529005
TEST=boot majolica, all USB ports work
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I6d3506bb4d54c7f8ea1e53576ef68d2aface6c89
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:181910592
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I7851d3b11ea3b026b999019d02df1144f8393753
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
BUG=b:180653357
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Ifd43d9cc1832d8ed8d90c68ba88b5667e3c04f89
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:180507937
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I7b8b2ab73d66e0aaa0e9b7570661c885f7f777ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51296
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Define the 26th bit of the fw_config for the regular touchpad
and numpad touchpad selection.
REGULAR_TOUCHPAD: 1
NUMPAD_TOUCHPAD: 0
BUG=b:174964012
BRANCH=zork
TEST=build pass
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: Ie2055d6bb45a64bc0e59209cecc0f8a31c0f3718
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
The VGA BIOS for AMD Padmelon and Google Zork are stored in `amd_blobs`.
Do not force inclusion of VGA BIOS when `USE_AMD_BLOBS` is not enabled.
Change-Id: I206e8fadc14ec0d9b162dc4d72813fdd3d43958b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This option defaults to n already.
Change-Id: I9f6407152f7cf2e2ac6fd1fff874e400f89a27ae
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Some of the previous binaries were incorrect and should not be used
for Majolica because they are templates instead of APCBs specifically
built for the board. This APCB update also places the UMA region under
4G and size 32 MB which is essential for video output.
TEST=Boot with UEFI BIOS and verify we can get to OS. Also verify memory
region size, base and alignment.
Change-Id: Id797e2ad5bd67815c09752aedc19dad7dcf8ad12
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add ".data_hold_time_ns" to follow I2C specification.
The adjusted result aobut 0.315us(more than 0.3us)
BUG=b:181091107
BRANCH=zork
TEST=emerge-zork coreboot chromeos-bootimage
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: Id92fadcb54b9722709e32ced1f0be001b8c97975
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:182269526
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I351fb4fc493bb92b31e2c8bc946dfb048045335c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51384
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
To define Mainboard Type config, use the fw_config bit[26].
Check MB Type to modify SDLE settings for different VCORE IC.
BUG=b:177193131
BRANCH=zork
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: If153c0a3e641ae32ef89737925bd9f62dfb71f3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Add the UPD updating hook in early stage for customization.
BUG=b:117719313
BRANCH=zork
TEST=build,check the hook function been executed.
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I4954a438a51b29b086015624127e651fd06f971b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51181
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current driver is using chip registers map to configure the SAR
sensor, which is opaque, especially when the datasheet is not published
widely.
Use more descriptive names, as defined in Linux kernel documentation at
https://www.kernel.org/doc/Documentation/devicetree/bindings/iio/proximity/semtech%2Csx9310.yaml
BUG=b:173341604
BRANCH=volteer
TEST=Dump all tables, check semtech property:
for i in $(find /sys/firmware/acpi/tables/ -type f) ; do
f=$(basename $i); cat $i > /tmp/$f.dat ; iasl -d /tmp/$f.dat
done
In SSDT.dsl, we have:
Package (0x06)
{
Package (0x02)
{
"semtech,cs0-ground",
Zero
},
Package (0x02)
{
"semtech,startup-sensor",
Zero
},
Package (0x02)
{
"semtech,proxraw-strength",
Zero
},
Package (0x02)
{
"semtech,avg-pos-strength",
0x0200
},
Package (0x02)
{
"semtech,combined-sensors",
Package (0x03)
{
Zero,
One,
0x02
}
},
Package (0x02)
{
"semtech,resolution",
"finest"
}
}
Change-Id: I8d1c81b56eaeef1dbb0f73c1d74c3a20e8b2fd7b
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:180507707
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I25ce0ca869ca854ff33242d2c416319e9688cc6f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51264
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:180507937
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I3cdd6422b1bc53ea934346327359cbc6d86baeeb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51043
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Define the ChromeOS GPIOs (physical write-protect and virtual recovery
mode) in ACPI tables so the OS knows which physical pad is used for them.
BUG=b:181887865
TEST=flashrom_tester is able to "see" the WP GPIO
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I3feed366afd6507894a1d31304891cc785a4d314
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51347
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Intel ADL-P supports an additional memory-mapped 16MiB window into the
platform SPI flash. Support for this window already exists at the SoC
level, so all that is needed is to properly organize the flash map to
take advantage of this. FW_SECTION_A moves down to the bottom of the
available space in the lower 16MiB half, and FW_SECTION_B moves to the
bottom of the top 16MiB half. RW_LEGACY is squashed down to 2M.
BUG=b:182088676
TEST=build and boot to OS from FW_MAIN_A
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I60483b7e638c0a7e41f1f7e2b5503ae02e9906bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51345
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Enlarge CONSOLE_CBMEM_BUFFER_SIZE from 128K (default) to 512K, so that
more DRAM calibration logs can be stored in CBMEM console.
BUG=b:181933863
TEST=emerge-asurada coreboot
TEST="cbmem -c" shows the whole full calibration log
BRANCH=none
Change-Id: If82cbee5d2d5e97d98cbdaecda739d91a7cca0f8
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51275
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fleex has other project share the same FW. Only fleex has LTE sku.
So we need to make sure it is fleex then check if LTE sku.
BUG=b:181946744
BRANCH=octopus
TEST=Check no SAR table can be loaded with sku id 4 and 5.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I9f3d5fed4315fc716acad1a07735221d154c377e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
|
|
This file is common for all the AMD platforms.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I10ee600b4bcd7aaff39bfab075eb4dbc9096b435
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51299
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch pulls control of the memory pool serving allocations from the
CBFS_CACHE memlayout area into cbfs.c and makes it a core part of the
CBFS API. Previously, platforms would independently instantiate this as
part of boot_device_ro() (mostly through cbfs_spi.c). The new cbfs_cache
pool is exported as a global so these platforms can still use it to
directly back rdev_mmap() on their boot device, but the cbfs_cache can
now also use it to directly make allocations itself. This is used to
allow transparent decompression support in cbfs_map().
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I0d52b6a8f582a81a19fd0fd663bb89eab55a49d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=b:181809122
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I64475a475e9b72a6edd04ce0728591e0649d9f60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:180456030
TEST=`mosys` is able to detect the platform correctly
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ifbaa4a380bdb546bb54d579b46fe5760b2f4b754
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
BUG=b:181887865
TEST=`crossystem` shows correct state of WP signal when toggled
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: If49ca1d70cc36ab74d70e858336679c0a9a3258e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
To reduce qualification effort, we want to pre-populate DRAM by their
size, package type and geometry so when a new DRAM is introduced we
don't need to spin off a new firmware release.
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: I42ee170c159e551e840ab4e748f18f5149506b4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51202
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Support 4G+128G MT29VZZZAD9GQFSM-046 W.9S9 discrete DDR bootup.
BUG=b:162292216
BRANCH=kukui
TEST=Boots correctly on Kukui.
Signed-off-by: Jessy Jiang <jiangchao5@huaqin.corp-partner.google.com>
Change-Id: I5657a007154bc52c6f0f27e1de6e3294a5e74ad7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48686
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
This change moves GPE configuration from brya0/overridetree.cb to
baseboard/devicetree.cb since all variants will end up using the same
configuration.
TEST=Verified using "abuild -p none -t google/brya -b brya0
--timeless" that coreboot.rom generated with and without this change
is the same.
Change-Id: Ie31bf2bf8a91da82fca77c78fb0a735a2645de55
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change updates MAINBOARD_PART_NUMBER string to use uppercase for
first character. This matches what all others boards do.
BUG=b:180456030
Change-Id: I10eaeef5ec662a5718b787a3f0e3705cf70d751d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51297
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:181843816
Change-Id: I25309a8f0900070a8307fbce90ccb6d47f9c3dfc
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51261
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:181843816
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I74246cd0d2f866022604ec3e8a8d523c273cdef4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:181160586, b:181843816
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ic201ad047fd0d593749d2b993f843f7e188a5c98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51258
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Implement the mainboard_tcss_get_port_info weak function so that the TCSS
muxes can be properly configured to ensure mapping is correct in mux. This
ensures that any devices that are connected during boot are not improperly
configured by the Kernel.
BUG=b:180426950
BRANCH=firmare-volteer-13672.B
TEST= Verified that the SOC code that initialized TCSS muxes to disconnect
mode is executing properly for all TCSS ports and verified that USB3 devices
are no longer downgrading to USB2 speed if connected during boot.
Change-Id: I59e5c5a7d2ab5ef5293abe6c59c3a585b25f7b75
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I46bc854239e723a1685279f634e635b72e7b3af9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the memory parts. The memory parts being added are:
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
H9HCNNNBKMMLXR-NEE
BUG=None
TEST=Build the blipper board.
Change-Id: Ia7e4c1d5c06013c1902816d6dcafb5a8a0386bb3
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update telemetry settings for vilboz.
VDD Slope : 26939 -> 27225
VDD Offset: 125 -> 187
SOC Slope : 20001 -> 26559
SOC Offset: 168 -> 89
BUG=b:177162553
BRANCH=zork
TEST=emerge-zork coreboot
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Iaf7c5083c4c5affec5ae0b5583efb5237e10d0ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: chris wang <Chris.Wang@amd.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
1. No gpio control in bootblock
2. Power on and then deassert reset at the end of ramstage gpio
3. Disable power and assert reset when entering S5
On "reboot", the amount of time the power is disabled for is
equivalent to the amount of time between triggering #3 and wrapping
around to #2.
This change affects the following volteer variants that include an FPMCU:
1. Drobit
2. Eldrid
3. Elemi
4. Halvor
5. Malefor
6. Terrador
7. Trondo
8. Voema
9. Volteer2
10. Voxel
BUG=b:178094376
TEST=none
Change-Id: Ib51815349cea299907c10d6c56c27bd239e499e7
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Modify USB port to match schematics.
And assigned USB2 port to type-c use.
BUG=b:177481079
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Change-Id: I25412d16df8ad809c05635022c11bd8882d002c5
Signed-off-by: hao_chou <hao_chou@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49980
Reviewed-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Loading wifi_sar-vilboz-1.hex for vilboz360 LTE sku for the present.
BUG=b:177684735, b:176168400
BRANCH=zork
TEST=emerge-zork coreboot chromeos-bootimage, then verify that tables are
in CBFS and loaded by iwlwifi driver.
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I477b55d64fd9d33d753b10b2de443041a12d13e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Change-Id: I3e82a51173f561df560c36528a9b7ec26cf489b5
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
1) Micron MT53E1G32D2NP-046
2) Micron MT53E2G32D4NQ-046
BUG=b:181378727
TEST=none
Change-Id: I413e35cdb7c34388c3e159f8f9584fae2d21a355
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Current implementation exposes GPP_F4 cnvi reset pin as reset
gpio instead of GPP_D4(BT_DISABLE_L). GPP_F4 is native and driven
by SoC. It should not be driven by driver.
BUG=b:180875586
Change-Id: I589fc2b55ee2947cc638fe17540bbd24f5bfb8f4
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51178
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ASL+ Optimizing Compiler/Disassembler version 20200925 remarks:
IASL build/dsdt.aml
Intel ACPI Component Architecture
ASL+ Optimizing Compiler/Disassembler version 20200925
Copyright (c) 2000 - 2020 Intel Corporation
dsdt.asl 222: Name(PSa, Package(){
Remark 2182 - ^ At least one lower case letter found in NameSeg, ASL is case insensitive - converting to upper case (PSA_)
dsdt.asl 228: Name(APSa, Package(){
Remark 2182 - ^ At least one lower case letter found in NameSeg, ASL is case insensitive - converting to upper case (APSA)
Execute the command below to fix all occurences:
git grep -l PSa | xargs sed -i 's/PSa/PSA/g'
Change-Id: Ia458c98a4774fb5745825aecf996a476e66eaa3f
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51152
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The `FORCE_ENABLE` and `FORCE_DISABLE` names do not match what FSP UPDs
say, and can be confused with the `PchHdaTestPowerClockGating` UPD.
Replace the enum with a bool, and drop the confusing names. Note that
the enum for Ice Lake was incorrect, but no mainboards used the option.
Change-Id: I2c9b4c6a2f210ffca946ca196299fa672a06ccc7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51154
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make the SATA LED blink when coreboot dies. GPIO functions aren't
compiled in for postcar, so add a check to prevent linker failures.
TEST: Try to boot Librem Mini WHL without RAM, observe blinking (and
also blinding LED). Re-install RAM (and re-seat RAM a few times),
boot to OS, and observe SATA LED operating normally, as expected.
Change-Id: I0ffac0ab02e52e9fbba7990f401d87e50a1b5154
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50013
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PCIEXP_HOTPLUG has a prompt and as such is not supposed to be forced.
Just change the default value to 'y'.
Change-Id: Ie4248700f5ab5168bff551b740d347713273763c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Pineview does not support PEG.
Change-Id: Ib0006dbd54e6f2031b97ed11ce61407ffcfa6244
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This is a cosmetic change.
Make the formatting consistent with the rest of the tree.
Change-Id: Ic90e5584938592f1c2ab41edfcc773702822070d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Booted fine on the first try. Most things work properly, but I haven't
tested them thoroughly. Native raminit chokes with a DIMM in the second
slot, but the first slot works properly.
Change-Id: I2126c7d31e0d8a8f80df69fdcdcd202b87f219a4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
There is going to be an upcoming board version for Drawlat/man and
Drawcia. Hence apply the override GPIO table without pad termination for
board versions 6 or 8 alone.
BUG=None
BRANCH=dedede
TEST=Build and boot to OS in Drawcia.
Change-Id: I320de9a0c37ac033f3efda74eeb8f36e34667fd4
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
These files were automatically generated by the lpddr4 version of
gen_part_id.go.
BUG=b:178715165
TEST=Build
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I3797ba6d52248961418000614a4f7885182521a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
These SPDs were generated by the lpddr4 version of gen_spd.go from the
global_lp4x_mem_parts.json.txt file.
BUG=b:178715165
TEST=None
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I7b9bd04534d6e45dbfe10a0028052978ef3d7c17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Looks like I forgot about trogdor-rev1 in CB:51004. Unlike rev0 (other
special case) or rev2 (works like CoachZ/Homestar), rev1 used the same
pin as Lazor and Pompom for EN_PP3300_DX_EDP. Apparently there are still
some people using these, so add in another special case for that.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I7093aa63778d69fde240af3b0c62b97ac99c28dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51196
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Most devices are now disabled by default in the chipset. Enable the
iGPU and two XHCI controllers that are required to boot the board.
BUG=b:180528708
TEST=To be tested
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I54a4547217fb8e9f67fc0c8e1e36e96dfaae331c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51095
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:180523962
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Ic8f30f6d7c4781d4e8451546b39395a74393608f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50882
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:180507937
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Ic607d6bca5c70255332a6fbee2b63e6daba7d1e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51047
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1) Both SAR sensors had a UID of `2`, making them indistinguishable
2) No `device` underneath max98357a `chip`
Change-Id: Icf586229532819a7779652cbee73755b036dfbdc
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51145
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Even though `device` entries are children of `chip` entries in the
devicetree source format, the chips in the translated C structures
are only hooked up to device nodes. Hence, to configure a chip in
a device- or overridetree, it always needs a `device` below it.
This should fix docking events for the X200 ThinkPad.
Change-Id: I561e7ae81f2e096a091868ce51daa1c8f66af067
Signed-off-by: Nico Huber <nico.h@gmx.de>
Found-by: Kevin Keijzer <kevin@quietlife.nl>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kevin Keijzer
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Enabling the GPIO_SIGN_OF_LIFE option will allow for early boot testing.
BUG=b:180721202
TEST=builds
Change-Id: I069623ae76a4e4d1e43a47dd95fdfcece398ebfb
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
This is to align with newer platforms.
Change-Id: If33ea3a7835ec071be3fd060f9712c47678bd6bf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50963
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modify I2C3 setting to follow I2C specification (lower than 400kHz).
Original setting:
.rise_time_ns = 184
.fall_time_ns = 42
Change to:
.rise_time_ns = 110
.fall_time_ns = 34
BUG=b:181091107
BRANCH=zork
TEST=emerge-zork coreboot chromeos-bootimage
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: Ibdbb9a7dde524bdbde4789ee7ea005646080d97a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51052
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ie3870bc666acaea316f00b205de512cf790e720c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Fill the ECC type in `struct memory_info` in romstage, and in SoC code.
The SMBIOS override is unnecessary, and this is not mainboard-specific.
Change-Id: I8370b3ee7d75914b895946b53923598adf87b522
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50179
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure I2C high / low time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (400 kHz).
Measured I2C frequency just as below after tuning:
touchpad:372 kHz
audio codec RT5682:386.8 kHz
speaker AMP L:387.5 kHz
speaker AMP R:388.9 kHz
BUG=b:181342340
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400kHz
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I05d78c088190e349281a34b2aeed39ae8d867dc2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51112
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ELAN touchscreen into devicetree for storo.
BUG=b:177389448
BRANCH=dedede
TEST=built storo firmware and verified touchscreen function
Change-Id: I0d9e5005928c6fda3d1f0ce8bd9ae135e4a04867
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50981
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:177834652
BRANCH=dedede
TEST=build kracko firmware
Change-Id: I360920f80f4ce5dcbcde25c433e23803fa72569b
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This reverts commit d510b60f5b4eee6c165039be4acbe89ff25d8a4a.
This patch includes the DSDT ASL code for shadowmountain board.
BUG=b:175808146
TEST= Boot shadowmountain board, dump and verify the DSDT ASL entries.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I5aa60730fc9b93fa97b2bafbb8b2714b6b37becc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch includes the ramstage changes for the
shadowmountain board.
BUG=b:175808146
TEST= Build and boot shadowmountain board.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I419eecefddf9ee6e4249ada041ebeb1b78e85eb7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49732
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Brya’s chromeos.fmd contains a region for RECOVERY_MRC_CACHE,
but does not select HAS_RECOVERY_MRC_CACHE, so it’s unused.
BUG=b:174266035
TEST=Check MRC cache can allocate in recovery mode.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I6b83eec3dcf27bafde610a701e55f1371a5d4571
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51081
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per CL:2641346, update GBB flag names:
GBB_FLAG_FORCE_DEV_BOOT_LEGACY -> GBB_FLAG_FORCE_DEV_BOOT_ALTFW
GBB_FLAG_DEFAULT_DEV_BOOT_LEGACY -> GBB_FLAG_DEFAULT_DEV_BOOT_ALTFW
BUG=b:179458327
TEST=make clean && make test-abuild
BRANCH=none
Signed-off-by: Joel Kitching <kitching@google.com>
Change-Id: I0ac5c9fde5a175f8844e9006bb18f792923f4f6d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Follow elan's suggestion to configure IRQ as level trigger to prevent touchscreen lost
BUG=b:180778934
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I3aca0ad20791c989dec9e70d69d637b28c9cc043
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50417
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a weak variant routine to allow variants to perform any needed
initialization in ramstage.
BUG=b:178094376
TEST=none
Change-Id: I65dc1cdf15b68d9f2239e02fcb4b2c902d749378
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50827
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPP_E11 should be configured to be routed via APIC to avoid
p-sensor communication error in OS.
BUG=b:178465379
BRANCH=dedede
TEST=run "i2cdump -y -f 15 0x28" to confirm registers as expected.
un-approach：
=> register address: 0x01 value: 0x00
approach:
=> register address: 0x01 value: 0x02
verify sx932x IRQ in "/proc/interrupts" loading as expected.
Change-Id: I7d639ec1f9b31b240475dc1c8025bf59ae1e8e0b
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50876
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the blipper variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:179648964
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_BLIPPER
Signed-off-by: chenzanxi <chenzanxi@huaqin.corp-partner.google.com>
Change-Id: I8e67521bd9ab05c257cb3d5d5d4cf506f258bfa7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
New boards introduced to trogodor family.
BUG=b:180668002
BRANCH=none
TEST=make
Signed-off-by: xuxinxiong <xuxinxiong@huaqin.corp-partner.google.com>
Change-Id: If0f9b6c89198a882acae7191d08b166eb8c1dd71
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Stamp_boost 1640 parameter is too short to keep APU performance.
Restore parameter to 2500 then APU could have longer boost time (~3xxx sec)
BUG=b:175364713
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test => pass
Change-Id: Ie08394d0b1a693f71336cb4cb6ce9528dfdce14b
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Because the entries were formatted differently to the baseboard, the
devicetree overrides didn't work as intended, and all 5 entries from
the baseboard were included, and then the overrides were applied, but
the baseboard's entries were kept, so there were duplicate ACPI
entries, which causes errors when parsing the table.
Fixes: 5f30ae3714d ("mb/google/volteer: update thermal table for Eldrid")
BUG=b:181034399
TEST=compile, verify static.c is correct now
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I32fe2eae591ed4d3c08378977c463327f7ee1100
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51044
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the first version DPTF parameters. The TDP is down to 13w for acoustic concern.
BUG=b:177777472
BRANCH=firmware-volteer-13672.B
TEST=build test image and verified by thermal team.
Change-Id: I36f016530a61e3660938ce8d2948bb3b0f275d88
Signed-off-by: Wayne3 Wang <Wayne3_Wang@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51030
Reviewed-by: Paul Yang <paul.f.yang@intel.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com>
Reviewed-by: Ariel Chang <ariel_chang@pegatron.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the first version DPTF parameters received from the thermal team.
BUG=b:177628854
TEST=cros build-ap --debug -b dedede --fw-name galtic
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Ia8e76d303db0add95e77693f15cad108fa92303b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49480
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=b:177399759
TEST=firmware_EventLog passed on asurada
BRANCH=none
Change-Id: I759f9030f525fa9e34ed542198a9dba8f25909f5
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Use different verb tables depending on board revision.
For board revision R03 and older use the existing verb tables.
For revisions newer than R03 use the new verb tables and also
apply the dynamic audio configuration recently added.
Also do the following:
* Use correct NID port mapping
* Fix verb count in ALC888 header
* Fix NID in Intel codec verbs
Change-Id: I24ea9149eb2cddb815ff82744a351c926a94aaef
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
List of changes:
1. Add mainboard Kconfig to Kconfig.name files
2. Handle mainboard names in Kconfig file for adlrvp
3. Created a new devicetree.cb for Adlrvp-m.
3. Add override devicetree for ADL-M RVP.
4. Configure proper PCI and USB ports as per schematics for ADL-M
BUG=None
BRANCH=None
TEST=Able to build ADL-M RVP variants adlrvp_m and adlrvp_m_ext_ec.
Signed-0ff-by: Maulik Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I997b89ba87fb03dfa6a836caec51efd05baa2e8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49871
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ELAN touchpad into devicetree for storo.
BUG=b:177393444
BRANCH=dedede
TEST=built storo firmware and verified touchpad function
Change-Id: I95780d23b9ea5425d7762e850c25fd14d8a9caf4
Signed-off-by: chenzanxi <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50979
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow vendor suggestion to configure IRQs as level triggered to prevent TS lost.
BUG=b:171440909
BRANCH=dedede
TEST=1. emerge-dedede coreboot chromeos-bootimage
2. power on, suspend DUT to check TS is functional
Change-Id: I07a5cd5e2ac9caad9dbcca12e05bda7f08f42dce
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
associated GPIO configuartion
Adding LTE module support into devicetree and associated GPIO configuartion.
BUG=b:177385043
BRANCH=dedede
TEST=LTE function is OK
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I4d91045176fd6413ac6a5eed70289a5668e5b94f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
speaker amplifier support into devicetree
Adding audio codec and speaker amplifier support into devicetree
BUG=b:177479444
BRANCH=dedede
TEST=audio function is OK
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I90ff3a107278c711a085d04ae708e41f95d454ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Adding Touchpad support into devicetree.
BUG=b:177348842
BRANCH=dedede
TEST=touchpad function is OK
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I7ecafb5b3e39ff2ed9e176531bd0939f830a6397
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
and associated GPIO configuration
Adding camera support in devicetree and associated GPIO configuration.
BUG=b:177351873
BRANCH=dedede
TEST=camera function is OK
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I539e969e180c8c71d4b54b50519d2e1ff25415f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
