| Age | Commit message (Collapse) | Author |
|---|
|
The firmware of devices connected to LPC should deassert the LPC CLKRUN#
signal when there is no bus activity on LPC.
Necessary changes:
- Enable LPC CLKRUN#
- Enable LPC PCE (Power Control Enable)
- Enable LPC CCE (Clock Control Enable)
- Remove I/O decoding range on LPC for COM 3
- Disable I/O UART driver
Change-Id: I2fd80e3fdcf23658f97b8182a77df7e09ddf25d6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Bayhub eMMC controller default runs SD base 50MHz at the first power on.
After boot into OS, mmc kernel driver will config controller to HS200/208MHz
and send MMC CMD21 (tuning block).
But Bayhub PCR register 0x3E4[22] (eMMC MODE select) is not clear
after system warm reset.
So eMMC will still run 208Mhz but there is no block tuning cmd in depthcharge.
It will cause two Sandisk eMMC (SDINBDA4-64G-V/SDINBDA4-32G-V) to fail to
load kernel and trap in 0x5B error (No bootable kernel found on disk).
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: Ic080682e67323577c7f0ba4ed08f8adafca620cc
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Reduce the CPU passive threshold sample rate from 5 seconds to 1
second so DPTF will react faster to rapid temperature increases.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BUG=b:113101335
BRANCH=atlas
TEST=manual performance/power testing on nocturne.
No longer see messages like below in syslog,
'CPU0: Package temperature above threshold'
Change-Id: I2dc9d157b54500bae29e123978bb8ad6e05ef619
Reviewed-on: https://review.coreboot.org/28325
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Reduce the CPU passive threshold sample rate from 5 seconds to 1
second so DPTF will react faster to rapid temperature increases.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BUG=b:67459049
BRANCH=nocturne
TEST=manual performance/power testing on nocturne.
No longer see messages like below in syslog,
'CPU3: Package temperature above threshold'
Change-Id: Ic20c718fd3a496db7c7192feec4f230d924cc458
Reviewed-on: https://review.coreboot.org/28324
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update TSR1 trip point from 48C to 50C.
Also, change power limit2 minimum value from 8W to 10W.
These are the values as per recent thermal tuning.
BUG=b:79779737
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: I33a9d2dc3e0e5566d95b1f1e46d3922dc8965b2b
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/28187
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit fixes the values and thus fixes the issue of
audio device not getting detected on random reboots.
Change-Id: I34a4f62815d192005c3324d4f71b0aba377fe738
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/28280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
|
|
Change-Id: Ie3ee4acfd272991133f02a56df6e23aa6071d3e9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Some unneeded includes are also removed.
Change-Id: Icd518c46d8503d11d24466c30840d7e514e9a05d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Most FADT report using ACPIv3 FADT table. Using the get revision
function keeps the table versions in sync.
Change-Id: Ie554faf1be65c7034dd0836f0029cdc79eae1aed
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28277
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch disables the unused PCI clock outputs on the XIO2001 PCI
Express to PCI Bridge.
Change-Id: I0b9cf51a713f4ab46e71d250397486d136c26177
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28284
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
add device "WCOM Digitizer" and "Synaptics Touchpad" for bobba
BUG=none
BRANCH=master
TEST=emerge-octopus coreboot
Change-Id: Ie0bf8ebab6d9cb9c8fe42a500efaa3d11ae359db
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28332
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
TEST: same sha256sum with BUILD_TIMELESS=1.
Change-Id: Icf3368bcf1351f0e7cd4041c3792d76362aec9e5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
To increase the lifetime of the circuit, it is necessary to reduce the
eMMC speed to DDR50 mode.
Change-Id: I40658b44a99e6600ed00950a1a177961f0055e7a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This enables CBAS device on Nocturne to allow hid-google-whisker driver
in kernel properly detect device configuration.
Change-Id: I5905a2de208e94062f2768a9b7d22147f85c7f38
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-on: https://review.coreboot.org/28262
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For the 1st redesign of mc_apl1 mainboard some adjustments are
necessary:
- The FPGA is now connected directly via a PCIe Root Port
- Internal Apollo Lake UARTs are now used
- Adjusting GPIO settings
Change-Id: I8917a52325306f24d1c39a88dac47b0cee760d57
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
A FPGA is not necessarily available in further mc_apl1 variants. So we
move the loading of the driver and the notify function to the mc_apl1
variant.
Setting the CPU to Max Non-Turbo Ratio is also not absolutely necessary
for further variants.
Change-Id: I9f8438407f231df08e1ad04655bb6f747257e268
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This supports the Foxconn d41s, d42s, d51s, d52s.
The following is tested (SeaBIOS 1.12 + Linux 4.9) and works:
- COM1
- S3 resume (with SeaBIOS needs sercon disabled)
- Native graphic init on VGA output
- SATA
- USB
- Ethernet
- PS2 keyboard
The base for this mainboard port was the Intel D510MO port.
Change-Id: Ie4ec9cbf70adcdddbc2e5d805e4806825c320072
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28227
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
src/mainboard/google/octopus/mainboard.c
Function dev_find_slot may return NULL,
check before its usage.
Found-by: klockwork
BRANCH=None
TEST=Built & booted Yorp board.
Change-Id: I160adbe3b0a5a2b0f11fd1567513860664d4bee3
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28235
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The change updates GPIO configuration for meep.
1. Update touchscreen power enable GPIO in devicetree.
2. Provide default override tables for GPIO configuration.
BUG=b:112955087
TEST=Boot on meep proto board with Intel (Jefferson Peak) wifi card.
Change-Id: Idb4e7a510eef15c2e118058d5848080782f4f665
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/28252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Since ifdfake has been deprecated in favor of better alternatives, such
as flashrom IFD parsing. Therefore, there is no need to support ifdfake
any further. Remove the IFD_*_REGION values on the few motherboards with
them.
Change-Id: Ie07116a7fb960c6ca832d802016f22c6677baac9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28232
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates the board id check for version >=2 to apply new
GPIO configs.
BUG=b:112618194
Change-Id: I3544c9596c465615818d2040682e554a64fc6b1a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28263
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This should not be board specific.
Change-Id: Ifa617e84af767f33a94f1ddfa7d4883c1a45198f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change PL1 from 4.5W to 7W, based on thermal test results.
BRANCH=eve
BUG=b:73133864
TEST=Verify the MSR PL1 limitation is set to 7W.
Change-Id: Ic3629f9c3b7eb6eef1a1b5a3051c9a11448bc9ad
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28078
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds support for controlling the keyboard backlight over ACPI.
BUG=b:112619894
BRANCH=none
TEST=verified keyboard backlight can be adjusted using keyboard
shortcuts
Change-Id: I25713f341e8b5a4e50903ac109bfa717f20969d8
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28205
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Enhanced Intel SpeedStep (EIST) on nocturne.
Change-Id: Ie9b832f5bc3a5ef300783bd9bcd7cf5d186b98fa
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable Enhanced Intel SpeedStep (EIST) on eve.
Change-Id: I49b18b817cda570f5c3c4d048c4e03329ac10b87
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch moves uart functions which are common across multiple soc to
block/uart. This will remove redundant code copy from soc
{skylake/apollolake/cannonlake}.
BUG=b:78109109
BRANCH=none
TEST=Build and boot on KBL/APL/CNL platform.
Change-Id: I109d0e5c942e499cb763bde47cb7d53dfbf5cef6
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This is meant to solve an issue where the proximity sensor may fluctuate
between CLOSE / FAR in rapid succession upon the user removing their hand
from the unit, before settling on the correct output.
Using the hardware debouncing filter solves this issue and removes the
spurious fluctuations.
BRANCH=None
BUG=None
TEST=manual on Nocturne, observing events come in
Change-Id: I78cc4852d42fcda6209fedce1ce91236b5814571
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/28112
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Weida touchscreen controller needs 130 ms delay after reset
BUG=b:111102092
BRANCH=master
TEST=Verify touchscreen on fleex works with this change
Change-Id: Ia86c3acf3c0e09ca05cc1681113672b546f830a0
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I4b0577bf3c00307733a1096749c1835d86764f29
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ib5799cceacefa89385a7615ef1c4b4d06157044f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Fix scope of ResourceSource, which should match the scope of the
device itself.
Change-Id: I9d0ff0ecc2721ec55b1ed12dddb495cd55966daf
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/28114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
All different memory configuration should be supported by now.
Thanks to Igor Lee.
Change-Id: Ib93c0e3cbdc29cbf6cff26292df4fbbb8208082f
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Igor Lee <getrun@gmail.com>
Reviewed-on: https://review.coreboot.org/27781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The romstage main() entry point on arm64 boards is usually in mainboard
code, but there are a handful of lines that are always needed in there
and not really mainboard specific (or chipset specific). We keep arguing
every once in a while that this isn't ideal, so rather than arguing any
longer let's just fix it. This patch moves the main() function into arch
code with callbacks that the platform can hook into. (This approach can
probably be expanded onto other architectures, so when that happens this
file should move into src/lib.)
Tested on Cheza and Kevin. I think the approach is straight-forward
enough that we can take this without testing every board. (Note that in
a few cases, this delays some platform-specific calls until after
console_init() and exception_init()... since these functions don't
really take that long, especially if there is no serial console
configured, I don't expect this to cause any issues.)
Change-Id: I7503acafebabed00dfeedb00b1354a26c536f0fe
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/28199
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After adjustment on Careena EVT
TP: 400.0 KHz
TS: 396.8 KHz
H1: 396.8 KHz
BUG=b:112663934,b:112664258
BRANCH=master
TEST=emerge-grunt coreboot
measure by scope
Change-Id: I9eeaf9290d95969a283f14618878e28faf0ea46f
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28119
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix the following failure from FWTS:
FAILED [LOW] AMLAsmASL_MSG_SERIALIZED_REQUIRED: Test 1, Assembler remark in line
131
Line | AML source
--------------------------------------------------------------------------------
00128| }
00129| }
00130| })
00131| Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
| ^
| Remark 2120: Control Method should be made Serialized (due to creation of named objects within)
00132| {
00133| Name (RBUF, ResourceTemplate ()
00134| {
================================================================================
ADVICE: (for Remark #2120, ASL_MSG_SERIALIZED_REQUIRED): A named object is
created inside a non-serialized method - this method should be serialized. It is
possible that one thread enters the method and blocks and then a second thread
also executes the method, ending up in two attempts to create the object and
causing a failure.
BUG=b:112476331
TEST= Run FWTS.
Change-Id: I6f4f6e7e94b01f673afc97d9415481ee63e406e3
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28122
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update SPD details to match with Coffeelake U RVP board
BUG=none
BRANCH=none
TEST=Boot on coffelake U rvp board and check if memory training is
passing and board boots till payload.
Change-Id: I953354cf5c6045731262f4f4e9da230187c2d246
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Update GPIO table as per board schematics.
GPIO table for other variants will be added later.
Change-Id: Ieb55d160ae2d6bff940840b1fba9411979332d4d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Nami doesn't support wakeup from hibernation by CR50. This causes the
device to remain turned off after CR50 update.
This patch disables turning off EC on cr50 update. CR50 resets the
whole system. So, EC reset is not required.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
BUG=b:112604277
BRANCH=none
TEST=gsctool -a -u /media/removable/cr50.bin && reboot
Verify EC reboots. AP prints 'Waiting for CR50 reset to pick up update'
then reboots.
Change-Id: I06f5eb6100e8af6ffec45d4de2b40eff44f89709
Reviewed-on: https://review.coreboot.org/28113
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These files are being updated to match the prevailing style
of cmos.default files.
Change-Id: I47d31d6fec8c9eb856aed0c63824d9556b7705e4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
change I2C irq to EDGE trigger
BUG=b:112616824
BRANCH=master
TEST=emerge-grunt coreboot
Raydium TS is working.
Change-Id: I86ec32bb3f2626e65d76c3259e3c4244a970e5de
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Used default console log level is 7 in src/console/Kconfig.
So let cmos.default use the same level as default.
Change-Id: Ia39ee457a8985142f6e7a674532995b11cb52198
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Side effect was observed that after override BayHub EMMC
driving strength to the max, EMMC CLK will be reduced to
51.x Mhz from 200 Mhz.
This will cause OS installation fail on Samsung EMMC sku.
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I848ab0cae474b15fbc4264c8ade63d5c6b4e489d
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This file contains two instances of "dptf_enable" = "1". This change
removes the 2nd instance (it doesn't have an explicit comment like the
1st instance).
The dptf devices still seem to be present even with this change, as
expected.
Change-Id: I890006644be9176ebaf555cc121c816e12f2b596
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The spec of the sx9310 says the I2C interface can handle standard
(100kb/s) and fast mode (400kb/s). The current setting is using fast
plus (1000kb/s) so this change is reducing the speed to fast mode.
I've been using the sensors with this change for a few weeks now, though
I also don't recall seeing an issue prior to this change.
Change-Id: I337fc02c52565d6ec4d7bac1b3564f65238962dc
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28075
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit 1fdb76945a9d06bbff37dee9da69e13a86c933f4.
Camera power is now handled by ACPI rules - no need to force the GPIOs
on by default.
BUG=b:80106316,b:111141128
Change-Id: Ifefec320884989f106a4b09c956d3a3279a1491a
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28072
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Ping-chung Chen <ping-chung.chen@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This defines new GPIO pin for controlling the display panel CABC
function. The default value is high (enabled).
BUG=b:112154569
Change-Id: I29083ab18e37f929a55b450b143463c67fe0abea
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28070
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This updates the DPTF sensor names to reflect the sensor locations on
the board.
BUG=b:75454415
TEST=verified new strings show up in
/sys/devices/LNXSYSTM:00/LNXSYBUS:00/INT3400:00/*/description
Change-Id: Ibffe6cb361de212ca03e75deaa8c454546d267a5
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28069
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ia38c6f8d978065090564d449cae11d54ddb96421
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch updates Power Limit (PL) for AML.
- PL1 as 5W TDP as POR
- PL2 as 18W TDP as POR
BUG=None
BRANCH=None
TEST=Build coreboot for Nocturne board and check default PL1/PL2 TDP.
cat /sys/class/powercap/intel-rapl/intel-rapl\:0/constraint_0_power
5000000 (5W TDP)
cat /sys/class/powercap/intel-rapl/intel-rapl\:0/constraint_1_power
18000000 (18W TDP)
Change-Id: Icb02a8a7c5fcd5e6aee45f14eba540a6b3ed3d67
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/27427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add TSR2 DART/DTRT package
BUG=b:110451144
BRANCH=nami
TEST=emerge-nami coreboot chromeos-bootimage
Test image with dptf.dv
Change-Id: I3328e17328415f5ebdcf84263e5456e11e55f769
Signed-off-by: T.H. Lin <t.h_lin@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This change updates GPIO configuration for bobba boards with id >= 1
This follows the same model as fleex:
a. Dynamically update touchscreen power enable GPIO in devicetree.
b. Provide default and bid0 tables for GPIO configuration in ramstage.
c. Configure WLAN enable GPIO differently in bootblock based on
boardid.
BUG=b:112354568
TEST=Built firmware for bobba
Change-Id: Id4ee4a1815e16ddfe60ed268688a8aaf4fb75579
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/28071
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Coffeelake U has 32MB flash chip support. Adding fmd file and enabling
CFL U board's Kconfig to output 32MB rom file.
Change-Id: I21431b7ac813781b12b95f80c6f8960a78caf4bc
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Add support for new board coffeelake RVP.
This patch is a copy patch and copies entire coffeelake_rvp folder from
cannonlake_rvp.
Changes done on top of copy:
1. Change copyright year from 2017 to 2018
2. Rename Cannonlake to Coffelake whenever applicable
3. Update entries in Kconfig and Kconfig.name
4. Rename variant directories to match coffeelake boards
Change-Id: Id37bfeb0ae51fd630fec96273216dbb2900782c7
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27904
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I189c981f3334836ab24bbc74491e9b58a2d403a4
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/27921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The paths defined in southbridge/intel/common/firmware/Kconfig should work just
fine.
Change-Id: Iaa780d9b3080416c6b1a7f24d97ecb8214962405
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28012
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All broadwell board set HAVE_IFD_BIN to default n, overloading the option in
soc, therefore just use the defaults in sb/intel/common/firmware.
Change-Id: I250dbbc9d61ecedc1a1eb48751ad966732604349
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28011
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is no need set the default HAVE_IFD_BIN explicitly to n.
Change-Id: I4a5fe45e7f8f6dd018937861b0fb92a8da49904e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28008
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is no need to redefine option present in
southbridge/intel/common/firmware/Kconfig.
Change-Id: I9999440031b07006e2df11e00dfb9f3dbe04f832
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28007
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix to accomodate for boards with more than 16 cores.
Change-Id: I35b61d94491c21ef76717f761e566ca815880f27
Signed-off-by: Samuel Jimenez <aerojsam@gmail.com>
Reviewed-on: https://review.coreboot.org/27847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I2c5edadfd035c9af08af9ee326a5a2dc8b840faa
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I3108193c0e0b644cecb74ae0c7a7b54e24a75b58
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I80dd65484fd52e9048635091fb20a123e959e999
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27869
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Current coreboot does not create ACPI device for OS to recognize Raydium
touchscreen.
List the touch screen in the devicetree so that the correct ACPI device
are created.
BUG=none
BRANCH=master
TEST=emerge-octopus coreboot
Change-Id: Ic61a69e19e97520da0702dfe6cb7496563fc34f4
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This was blindly copied from logs created under vendor BIOS in non-descriptor
mode which apparently set LAND in BUC.
Change-Id: I94c917600421ee742ece7f6f71309da80261da28
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Remove icc_max overrides to allow SoC code to set proper
icc_max based on CPU SKU.
BUG=b:78122599
BRANCH=none
TEST='emerge-nocturne coreboot chromeos-bootimage', flash to
nocturne, boot to kernel and verify device doesn't hang after
a few minutes.
Change-Id: I37c44e2428b802d754f2b12b8a57601d257e6582
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27996
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds a function to overwrite PL2 setting based on CPU
sku. From doc #594883, PL2 is 18W for AML-Y.
BUG=b:110890675
BRANCH=None
TEST=emerge-nocturne coreboot chromeos-bootimage & test with AML-Y
and KBL-Y skus.
Change-Id: Idfdc0c2434fdef56a7c25df05e640837a5096973
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27997
Reviewed-by: Caveh Jalali <caveh@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds a function to overwrite PL2 setting based on CPU
sku. From doc #594883, PL2 is 18W for AML-Y.
BUG=b:110890675
BRANCH=None
TEST=emerge-atlas coreboot chromeos-bootimage & test with AML-Y
and KBL-Y skus.
Change-Id: I468befcd2c4ad6c2bb9ae91b323a43f87ff65a26
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/27765
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow thermal table (b:112274477 comment#1) for first tunning.
BUG=b:112274477
TEST=Match the result from DPTF UI.
Change-Id: I63b2e50a4f6fc5453e6564e277600498ac0e6244
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Enable the GEO SAR feature for Octopus. Program wifi_sar VPD key.
coreboot reads the VPD and creates the ACPI table as per the WGDS spec.
BUG=b:112288077
TEST=Program VPD key, extract acpi table ssdt and valiate WGDS entry.
Change-Id: I40a6fd9e0ec8b440996bf3389322fd89bcca15a4
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
PERST signal is asserted/deasserted by ACPI routines during
suspend/resume. Configuring IOStandby for WLAN_PE_RST can result in
failure to resume from suspend state with wake-over-WLAN. This change
removes the IOStandby configuration for WLAN_PE_RST.
BUG=b:112371978
Change-Id: Ic7c0b2aa144233f8bbb4e5169d96347a1290abe1
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27994
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
When CNVi is being used, external wake using GPIO_119 is not
required. This change configures GPIO_119 as PAD_NC if CNVi is taken
out of reset.
BUG=b:112371978
Change-Id: Ifee90f428ed43c4d7c612c170476aff43b4a33ce
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change uses drivers/intel/wifi chip for CNVi device to ensure
that:
1. Correct device name shows up in ACPI node
2. It is possible to pass any parameters from devicetree to wifi
driver for SSDT generation.
BUG=b:112371978
Change-Id: Ia49820dd4f9cf2e0a9ef14931fbddd8a723208c0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change checks to see if CNVi module is out of reset:
1. If yes, then PCIe device for WiFi is disabled.
2. If no, then CNVi device is disabled.
BUG=b:112371978
Change-Id: I6e6cf2e646c897df017913056db87ac0cffa1a8e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27961
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
I2C2 is unused on all octopus variants. This change disables it in
devicetree.
BUG=b:112458032
Change-Id: I55abef864c06a448011f9570d3e6c0aa8bfdc5bc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28016
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates GPIO configuration for fleex boards with id >= 1
This follows the same model as phaser:
a. Dynamically update touchscreen power enable GPIO in devicetree.
b. Provide default and bid0 tables for GPIO configuration in ramstage.
c. Configure WLAN enable GPIO differently in bootblock based on
boardid.
d. Disable unused I2C devices in devicetree.
BUG=b:112458032
TEST=No errors observed on boot-up on fleex.
Change-Id: Ib4c449168b08e2393e2395d6b49469be5599c2ce
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The file `data.vbt` matches the VBT in the latest version of the vendor
firmware (version 3603). Tested with Linux 4.9 and everything works as
expected.
Change-Id: I8e3b1d274ac0df63989d966f477013e780611fa1
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/28050
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ib0839933f8b59f0c87cdda4e5374828bd6f1099f
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/23759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Allow for shared dram configuration by introducing a new table
that collapses the common settings after removing the part
numbers. When employing this scheme the part number comes
from CBI.
BUG=b:112203105
TEST=Placed part number in cbi. Faked out memory sku id. And enabled
DRAM part num always in cbi. Everything checked out.
Change-Id: I5229695ce3eb686421b89ac55d8df4b9fcec705c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/27991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Options that were deemed unneceesary on other code reviews have
been removed from the layout files. In addition, the checksummed
range has been extended to cover sata_mode and gfx_uma_size.
Change-Id: Id9e904f447809231806a786e39ed638f21e1bc5a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/27217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
I ported ga-h61m-s2pv based on the two Gigabyte b75m boards.
Based on another mainboard's code review comments, this patch
improves the code quality of these three similar boards.
ga-h61m-s2pv is tested and confirmed to be working, but I cannot
say the same regarding the other two mainboards as I do not have them.
Change-Id: Ib7747cceb5ba56f791677204cdc4c54c129c70c3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/27211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Rotor is dead, long live [PROJECT NAME REDACTED]!
Change-Id: Ia9308944257255e077a44c1df262c7f49c69890c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/27964
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add 3 new Kconfig options:
DRAM_PART_NUM_IN_CBI
DRAM_PART_NUM_ALWAYS_IN_CBI
DRAM_PART_IN_CBI_BOARD_ID_MIN
These control whether to 1. attempt to use CBI at all 2. always use cbi
and 3. conditionally use cbi based on board id. The intent is that the
MIN variant would be used for the tranisition period then cut over to
ALWAYS after full transition. Since multiple OEMs have different
schedules these options are there to bridge the gap. yorp. bip, and
octopus build targets would never flip DRAM_PART_NUM_IN_CBI, but in case
someone does the MIN values are 255 to always take the old path.
BUG=b:112203105
TEST=Set correct part number on phaser during testing.
Change-Id: If9a0102806d78e89330b42aa6947d503a8a2deac
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/27946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ief6a04ccb63658b5fb03cd1d298bf00948cf7410
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Careena EVT SanDisk EMMC sku has high fail rate of 0x5B reboot failure.
It'll need to increase 1.8V EMMC CLK/CMD, Data driving strength for
this issue.
CLK[6:4]
CMD,DATA[3:1]
original register value: 0x6B
enhanced: 0x7F
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I3db38ff12c566c258895c6643008a0472ca528bb
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27816
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Micron material that was broken has long since been fixed that
required this option. glkrvp had these stale entries and were
subsequently copied to octopus. Remove the need for this option.
BUG=b:35581751
Change-Id: Id73584367c2ad0e4958b5ea0f04a28e5fc82d085
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/27959
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Skylake SoC code now sets the icc_max based on the CPU SKU, so we
should not hard-code it in the device tree.
BUG=b:110890675
BRANCH=None
TEST=boots on atlas
Change-Id: I7eb3499b7bea9ab2c49e1f299e2dbb688c8d1c33
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com>
|
|
This configures the ACPI FADT perferred power management profile to
PM_MOBILE instead of PM_DESKTOP.
I'm not sure what impact this actually has. I just noticed the other
boards have it set.
BUG=b:110971913
TEST=Made sure SYSTEM_TYPE_LAPTOP shows up in coreboot.config
Change-Id: Iea1b8359b80d167e69745358f543f025713294ba
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The devicetree is not run through a C pre-processor, so remove it.
Change-Id: I161be45b2035f3a8724bf3217260e7571c429da8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27927
Reviewed-by: Naresh Solanki <naresh.solanki.2011@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If GPP_E22(CABC_EN) remained floating GPI(SoC default) at V3.3_DX_EDP on,
it may cause damage on the GPIO pad.
To prevent, we would set this pad to GPO on romstage before EDP power on.
Since we need to cover all systems in market, I put it into romstage
instead of early_gpio_table.
BUG=b:111860510
BRANCH=poppy
TEST=Verified CABC_EN is set to GPO high 5ms before EDP power on
Change-Id: I34e2fe86329a88eb05e0ea3c6beac6a64754b41e
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds variant callback to get GPIO configuration table in
romstage and configures these GPIOs before memory training is
performed.
BUG=b:111860510
BRANCH=poppy
Change-Id: I1eb51356fb3f4c0f4ff29b22dbcde6dbece303ad
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change provides implementation of smbios_mainboard_sku() to add
proper "skuX" string to SMBIOS table 1.
BUG=b:112163362
TEST=Verified "dmidecode -t 1" reports skuX correctly.
Change-Id: I7e42d2c80d791ea7170d066d2eeaa0c6811eb9c9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add default PSPP AGESA setting for Kahlee/Grunt mainboards.
BUG=b:112020107
TEST= build test
Change-Id: I8a8605402379de88a04f3a16553c308513fa1531
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Now that an updated bootloader with important fixes is available at coreboot
repository, all stoneyridge boards should use it. Move the selection of
SOC_AMD_PSP_SELECTABLE_SMU_FW from mb/google/kahlee to soc/amd/stoneyridge.
BUG=b:111428800
TEST=Build and boot grunt.
Change-Id: Idf8e348efbc85569aa1163125f412c5242c46eb4
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27844
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update power limit1 value from 8W to 10W. There is an error
in the energy calculation for current VR solution on GLK.
Experiments show that when power limit1 set to 10W, gained
performance improvement with SoC TDP reaches max (6W) power.
BUG=b:79779737
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: Ic320d442e7401e4be2e8e16d691db4c803f0fdc1
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/27819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds ACPI properties for WDT8752A device.
BUG=b:111402335, b:111102092
BRANCH=master
TEST=Verify touchscreen on fleex works with this change
Change-Id: Id186d5b87343007ae7e631d5d27464ee27e5b27d
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use the default value for Iccmax which is specified in vr_config.c.
The AcLoadline and DcLoadline keep the poppy value. Besides, the
USB 2.0 ports located on the mainboard are set to USB2_PORT_SHORT
and the others on the daughterboard are set to USB2_PORT_LONG.
Those setting need to be fine tuned later.
BUG=b:111579386
BRANCH=Master
TEST=Build pass
Change-Id: Icabfac04c94b3d480872c243d811509e274ef122
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The gpio setting is based on the proto board schematics
BUG=b:111579386
BRANCH=Master
TEST=Build pass
Change-Id: I20fc081d372b8686f6128a7e85276f9c6798b199
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add memory configuration based on the proto board schematics
BUG=b:111579386
BRANCH=Master
TEST=Build pass
Change-Id: I45efdc7893b5bcbca0de6e932e1452cc1a2ff028
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Rammus uses DA7219 Headset, Maxim MAX98927 Smart Amps and 4 channel dmic
BUG=b:111579386
BRANCH=Master
TEST=Build pass
Change-Id: If21a3870ee4b000a776d2f3e025fb43ef2fe48c7
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
