| Age | Commit message (Collapse) | Author |
|---|
|
Board Scarlet doesn't use usbphy1.
BUG=b:37685249
TEST=boot Scarlet, check the firmware log, and confirm
no errors about USB1
Change-Id: I66e0d8a235cc9057964f7abca32bc692d41e88fd
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/19489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add some known good values for some thinkpads displays.
Known good means that at this pwm frequency the display is evenly lit
on all duty cycles, the display makes minimal to no noise at lower
duty cycles and the display does not flicker. This values differs from
vendor (which uses an obviously wrong display clock (190MHz instead
of 320MHz) resulting in frequency more than 60% off the intended
value.
TESTED on Thinkpad X200 with edid ascii string in list and removed
from list to see if notice message is shown.
Change-Id: Id7bc0d453fac31e806852206ba2c895720b2c843
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19500
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
1. Add support for using cr50 I2C TPM on poppy. This will not be
enabled until the next build.
2. Also, configure GPIOs for SPI and I2C TPM only if the corresponding
Kconfig options are set.
BUG=b:36265511
TEST=Verified on a reworked board that I2C TPM communication works
fine.
Change-Id: I3b293b8d410a6973a6dfea393c17d0be425b6a28
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update GPIO table to match the schematics for next build.
Change-Id: I949a14bfaa7972f2257a0b11ee81dcb0771e2f7f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19517
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
The AFC—Additional Flash Control Register is set by
southbridge code.
Remove redundant calls and get rid of it in autoport.
Change-Id: I627082e09dd055e3b3c4dd8e0b90965a9fcb4342
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19493
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Based on Thinkpad x230 and schematics.
Verified by autoport.
USB debug port is the left front usb port
Thanks to Holger Levsen for the device.
Change-Id: I97c8e01a3ce0577d7dc9e8df7d33db3b155fe3d6
Tested-on: lenovo x1 carbon gen 1
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/16994
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Haswell, Broadwell, Baytrail, and Braswell ChromeOS devices'
FADT version were incorrectly set to 3, rather than the correct
ACPI_FADT_REV_ACPI_3_0. The incorrect value resulted in these
devices reporting compliance to ACPI 2.0, rather than ACPI 3.0.
This mirrors similar recent changes to SKL and APL SoCs.
Test: boot any affected device and check ACPI version reported
vai FADT header using OS-appropriate tools.
Change-Id: I689d2f848f4b8e5750742ea07f31162ee36ff64d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19498
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Enable audio:
* Add verb table for ALC286 & ALC298
* Enable virtual channel 1 for DmiVc1 & HdaVc1.
TEST= Build for kblrvp3 as well as kblrvp7. Boot to OS & verified
working of audio on both the boards.
Change-Id: Id27e3cf585b93ed4131d7bf3d3b53d3f5404b18e
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/18875
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable/Disable the PCIe ports to match factory BIOS. The port #6
is used for PCIe on the M.2 connector which allows for NVMe SSDs
to function.
Change-Id: I8058cbad3da651144545d588c0ae78c5f5e598ac
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19446
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Correct the default GBB_HWID to "ROWAN TEST 9387"
BRANCH=chromeos-2016.05
BUG=b:35774871
TEST=emerge-rowan coreboot chromeos-bootimage,
strings /build/rowan/firmware/image.bin | grep "ROWAN TEST"
and look for 9387 in output
Change-Id: I7851010305caf056958c8a6a328b0506bf2208cd
Signed-off-by: Patrick Berny <pberny@chromium.org>
Reviewed-on: https://review.coreboot.org/19488
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
BUG=b:37712455
Change-Id: I3209aaef774712edab5e9f656ee84bfb6917b1c1
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19472
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
BUG=b:37712790
Change-Id: I7764b4ec55b0beea82eeb6c379ef38ceeb1fb04e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19471
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable separate MRC cache for recovery mode. This requires change in
flash layout to accomodate another region for RECOVERY_MRC_CACHE.
BUG=b:37682566
TEST=Verified following scenarios:
1. Boot into recovery does not destroy normal mode MRC cache.
2. Once recovery MRC cache is populated, all future boots in recovery
mode re-use data from the cache.
3. Forcing recovery mode to retrain memory causes normal mode to retrain
memory as well.
Change-Id: I4c748a316436001c5a33754084ab4a74243e21df
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19457
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I1ef1323dc1f3005ed194ad82b75c87ef41864217
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19367
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I3a55c2e8077fdb10768df287f38efcd5e2e64bdf
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19365
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This needs some extra headers in amdk8/raminit.c that were otherwise
provided by that file.
Change-Id: I80450e5eb32eb502b3d777c56790db90491fc995
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19360
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
BUG=b:35647967
TEST=boot from bob
Change-Id: I756513f02ac13e159d5b8b1ac2346fa42cf3c219
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cf18ed7b8fdf11594f812e5c48a2bd0fde5cb820
Original-Change-Id: I50c053ab7a6f6c14daee4fb2ab1cdcaeee2d67da
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/452286
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19434
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
SD card detect pins should normally have a pull-up. It seems that for
micro-SD cards this doesn't really matter all that much, but for the
full-size slots we have on some Oak-derivatives (like Hana) it does.
BRANCH=oak
BUG=b:35854317
TEST=Booted Hana, confirmed that card detect no longer seemed stuck-on.
Booted Elm and confirmed that SD card behavior didn't change.
Change-Id: I9b20e0f6fe310e724d191e36ca0a81ab4fe5f593
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c2781eeef50f52c6f02ee9344274ddf4dcb0a946
Original-Change-Id: I428ac92efb07f94265673b04e0e0dd452649b9fd
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/452861
Original-Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://review.coreboot.org/19432
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The new touchpad firmware uses i2c-hid instead of custom reporting
protocol. The touchpad also exposed another slave address (0x1e) for
kernel to communicate with the touchpad EC.
Change-Id: Iecaf14f7b8aed836120569e9ade9c3115bc00264
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-on: https://review.coreboot.org/19461
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
In order for PD charge events to properly notify the OS when a charger is
attached we need to enable the PD MCU device and event source from the EC.
Without this change the charging still happens, but the OS does not notice
and update the charge state icon in the Chrome OS UI.
BUG=b:35586577
BRANCH=none
TEST=On a poppy board that has the VBUS rework applied, plug in a charger to
either port and see charge status updated to indicate charging in the
power_supply_info tool and the Chrome OS UI.
Change-Id: I59dcfc1cb5d11841f56cac7f4ffe461c2f9ec52a
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/19441
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
|
|
For this debug.c needs to be linked too.
Change-Id: I9cd1ffff2c39021693fe1d5d3f90ec5f70891f57
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19030
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
BUG=b:37684299, b:35775024
BRANCH=None
TEST=reboot and ensure graphics are displayed through
HDMI port.
Change-Id: I74a664b2d42f55adfa64f292f6ede4c956e16fbf
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19451
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:37486021
BRANCH=None
TEST=compile coreboot and make sure sda and sdb show
up in /sys/class/block.
Change-Id: I11344a4a5fc7e5b5d907d25439f92744a5fb70da
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19450
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I324edce44ad82217ac1fba177f4a0bb3c799308c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19426
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Replace ram_check with quick_ram_check, because ram_check is slow and
is destructive for dram content.
Change-Id: I5fb1bfe711549aabb6e597bda22848988a7e9cbe
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19416
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The silicon specific mainboard_romstage_entry() in amd/cpu/car.h,
which is used by all AMD silicon car code, caused a conflict.
Move the silicon specific defines to silicon header files. Also,
no longer include car.h in the romstage file.
Change-Id: Icfc759c4c93c8dfff76f5ef9a1a985dd704cfe94
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18769
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The devicetree data structures have been available in more than just
ramstage and romstage. In order to provide clearer and consistent
semantics two new macros are provided:
1. DEVTREE_EARLY which is true when !ENV_RAMSTAGE
2. DEVTREE_CONST as a replacment for ROMSTAGE_CONST
The ROMSTAGE_CONST attribute is used in the source code to mark
the devicetree data structures as const in early stages even though
it's not just romstage. Therefore, rename the attribute to
DEVTREE_CONST as that's the actual usage. The only place where the
usage was not devicetree related is console_loglevel, but the same
name was used for consistency. Any stage that is not ramstage has
the const C attribute applied when DEVTREE_CONST is used.
Change-Id: Ibd51c2628dc8f68e0896974f7e4e7c8588d333ed
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19333
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In the safety considerations, we should make sure the slot of SD is
enabled first, since we want to the power switch of corresponding is
powered up.
The different boards have the different power switch for sdmmc.
Some power switch IC need turn on delay for long time.
let's move the slot power of SD to romstage and avoid explicit delays
or per-board.
BRANCH=none
BUG=b:35813418, b:35573103
TEST=check the signal for children of gru, and boot up from sd card.
Change-Id: Id164e4c4c900c6b1ca0251fc27db4cd36c56f6ff
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ea1b01cc13628033b85251dbb44407f075efdc85
Original-Change-Id: I48ab543143d3de9be46608fc12d78e09decf8d79
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/447076
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19430
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Delete the write to PM register 0xee. This register is not
listed in the current BKDG and S4 is not currently supported
on this APU.
NDA document #47517 "A55/.../A85X fusion Controller Hub Register
Reference Guide" provides some clues on the intent of this write.
This register has always been observed to power on with a value
of 0x08 so the write has no effect.
This should be revisited again when SMI and PSP fully implement
the support required for S3.
Change-Id: I35e6c5f7ad1de7f51b018543d2f7ce82182f11e4
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18494
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Unlike other oak derivatives, Rowan uses an 8-lane BOE tv097qxm-nu0
MIPI/DSI panel that requires dual DSI support.
Rework oak display initialization to special case Rowan, which uses a
provided edid struct for its panel, special panel backlight sequencing
and needs to configure mtk_ddp and mtk_dsi to use dual dsi mode.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: I136ba5bd1ab12c4ad92995e066fc6d6cf54d0898
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19389
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The MT817x display output pipeline can be configured to drive an 8-lane
MIPI/DSI panel using "dual DSI" mode. For the "dual DSI" video data path,
the UFO block is configured to reorder the data stream into left and right
halves which are then sent by the SPLIT1 block to the DSI0 and DSI1
respectively. The DSI0 and DSI1 outputs are then synchronously clocked at
half the nominal data rate by their respective MIPI_TX0/MIPI_TX1 phys.
Also, update the call sites in oak mainboard to avoid build breakage.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: Id47dfd7d9e98689b54398fc8d9142336b41dc29f
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19361
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This helper function was introduced so that mainboards don't need
to manually fill in these struct edid fields.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: Ic9404a786a28b314b710e037dcae776be4b584ca
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19388
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch enables TPM2 using cr50 over I2C for the Rowan board, and
adds an mt8173 specific TPM IRQ polling function. The function relies on
the appropriate EINT input configured to trigger the ready status on
the rising edge.
The cr50 TPM is on I2C address 0x50.
The cr50 interrupt GPIO is also made available for use by depthcharge
via the coreboot tables.
BRANCH=none
BUG=b:36786804
TEST=Boot rowan w/ serial enabled, verify coreboot and depthcharge are
configured to use IRQ flow control when talking to the Cr50 TPM.
Change-Id: If6cdd0e39e4ac86538f27f322c55c329179ee084
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19364
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
DRIVER_TPM_I2C_IRQ has been removed. TPM_TIS_ACPI_INTERRUPT now specifies
the TPM2 ACPI interrupt used by intel's tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: If66a2a1d461a411e112589c84a434066d48b9399
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19410
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
DRIVER_TPM_I2C_IRQ has been removed. TPM_TIS_ACPI_INTERRUPT now specifies
the TPM2 ACPI interrupt used by intel's tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: Ia1eacd15e71a46a37457ee2f117b156393c3393d
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19409
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
TPM_TIS_ACPI_INTERRUPT specifies the TPM2 ACPI interrupt used by intel's
tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: Ic69add8a3ce35be64fb37db4ed40163f6144fc9c
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19408
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
TPM_TIS_ACPI_INTERRUPT specifies the TPM2 ACPI interrupt used by intel's
tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: Ifeb09a0a35bff7cd9091f6d027f0065288ca35c9
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19407
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Utilize the intel/common code for tis_plat_irq_status() to remove
dependencies and code duplication on for bringing up a board
requiring tis_plat_irq_status().
Change-Id: I2aaa1d7d3ce171dc1788438ff9990fce533deb6c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19371
Tested-by: build bot (Jenkins)
|
|
The CR50 TPM can do both SPI and I2C communication. However,
there's situations where policy needs to be applied for CR50
generically regardless of the I/O transport. Therefore add
MAINBOARD_HAS_TPM_CR50 to encompass that. Additionally,
once the mainboard has selected CR50 TPM automatically select
MAINBOARD_HAS_TPM2 since CR50 TPM is TPM 2.0.
Change-Id: I878f9b9dc99cfb0252d6fef7fc020fa3d391fcec
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19370
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
TESTED on D510MO.
Change-Id: I05aa40df0d2a090fcf734416669e9e1bbff094e4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19414
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
For raminit to succeed on a hot reset the following things are
prevented from running:
* Clearing self refresh
* Setting memory frequency
* programming sdram dll timings
* programming rcomp
TESTED on Intel d510mo.
Change-Id: I8f7e5c2958df29a96cdf856ade2f4f33707ad362
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19337
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
There is no need to override CBFS_SIZE since there is no additional
firmware needed on the flash.
Also due to it having a description CBFS_SIZE was displayed twice in
menuconfig, which is fixed by this.
Change-Id: I1a8e2e458ac4d420f3fd4628c2805b6d4e2ee529
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19331
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Tested on X230 with an external screen connected to every one of the
DP ports (miniDP on mainboard, two DP ports on dock), the GRUB payload
can display on both the external screen and the internal LVDS screen.
This is a copy-paste of I8e02c8003ff745d05ee272c59377174847f5219c.
Change-Id: I8f270d558668c1fe41bcdcc7d6d2aa7f053c85b6
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/19412
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Lid switch is not available.
Hence report lid state as always open.
Change-Id: Ia9c82c3ad323912bad51cf55ed80a37b3110b1ef
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/19219
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Configure PCI root port as per schematic.
Change-Id: I10ef682e8c54e22f328db5105d4da39c72ac2bed
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/19390
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Read DRAM SPD and populate MemorySpdPtr fields
in UPD data structure for FSP.
BUG=b:36490168, b:35775024
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/fizz -x -a
We are currently working on bringup and have no
hardware to test on yet.
Change-Id: I191cc6bf1fd8aa461855c538b48fd39e3ffd7848
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19205
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This board was added while the latest libgfxinit changes were in review.
Update to make it compile again and sanitize the port list.
Change-Id: I81b96e225945a8f8e47b64cefea91eb2747675ca
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19353
Tested-by: build bot (Jenkins)
Reviewed-by: Nicola Corna <nicola@corna.info>
|
|
TPM ACPI entries are automatically generated, and the old static
TPM ASL file is obsolete. Remove the reference to this obsolete
static and empty ASL file.
Delete src/drivers/pc80/tpm/acpi/tpm.asl.
Change-Id: I6163e6d59c53117ecbbbb0a6838101abb468de36
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19291
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
In the single GPU configuration, the T420 has an LVDS port, one DP++
and one VGA port connected to the IGD. Docking solutions feature up to
two additional DP/DVI-D ports, also directly connected to the IGD.
This makes the list of ports to probe pretty long (takes about 70ms
if nothing but LVDS is connected). We could save about 20~30ms if we'd
limit the ports in case we are not docked or have a discrete GPU.
Change-Id: I8e02c8003ff745d05ee272c59377174847f5219c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19378
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This commit changes the interrupt configuration for the touchpad to be
level triggered so it matches what the device is actually using.
When the system wakes from suspend by way of touchpad interrupt, or
there is touchpad input while in suspend that does not wake the device
(when the device is in tablet mode) the interrupt edge is not seen by
the AP so the driver does not handle the event and the touchpad keeps
the interrupt asserted and does not send further interrupts. The end
result is a non-functional touchpad after resume until it is reset or
the driver is reloaded.
This happens because the touchpad is actually treating the interrupt as
level triggered and expects the kernel driver to read a data packet over
I2C before it will de-assert the pending interrupt.
BUG=b:35774857
BRANCH=none
TEST=Test that the system can reliably wake from suspend by touchpad
event via the EC and continue to have a functional touchpad after resume.
Change-Id: Iaf7c04d9bc9d945bdcc196dff54c92a2a68368f3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19382
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Issue TPM startup on romstage completion via common LPC TPM
code if the TPM was enabled in Kconfig.
Change-Id: Id886d6aeefa045fb979f128b1cf4c10fff243b24
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/19338
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Kevin's center logic isn't super clean so it needs 925 mV for center
logic. All newer gru variants only need 900 mV.
BRANCH=gru
BUG=b:37429075
TEST=Reboot tests
Change-Id: I8c3bd6c245700b23c27cd5758c35c9993f801cb4
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/479463
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19357
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
It seems that we should only ever run at 900mV on center logic.
Changing it to 950mV before might have just masked over problems that
are now fixed.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=on kevin, run
stressapptest -M 1536 -s 1000
Change-Id: I5a09b1b403df800396bb2f2e8c76d14a4519d44a
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/391032
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Commit-Queue: Lin Huang <hl@rock-chips.com>
Tested-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19356
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Create Soraka board which derives from Poppy, a KBL reference board.
More Soraka specific changes need to be done later on.
BRANCH=master
BUG=b:36995255
TEST=Build (as initial setup)
Change-Id: I8af68d2cf475df56336aa0e3bebe86a54ece1999
Signed-off-by: YH Lin <yueherngl@chromium.org>
Reviewed-on: https://review.coreboot.org/19343
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Move current NHLT configuration implementation to baseboard so that
variants can leverage it or provide their own configuration.
BUG=b:37375693
Change-Id: I2a4317c112f9e3614bd01eb6809727b73328d29d
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19326
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add support for memory configuration by providing weak implementation
from the baseboard. All SPD files are present under spd/
directory. SPD_SOURCES must be provided by the variants to ensure that
required SPD hex files are included in the SPD binary.
BUG=b:37375693
Change-Id: Ic9bcc03d5a35bebd14061680f264ac072b3c0634
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19325
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add support for ChromeOS GPIO ACPI table information by providing weak
implementation from the baseboard.
BUG=b:37375693
Change-Id: I641afe6bb45f106ddebde081a8ac2c64278ebeb9
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19324
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Provide APIs for board_id() and gpio table functionality. Default weak
implementations are provided from the baseboard.
BUG=b:37375693
Change-Id: Ic3c946e6cb12b3c8ef3e83a1037ed0fc8cffbded
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19323
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In order to be able to share code across different poppy variants,
provide the concept of baseboard and variants. New directory layout:
variants/baseboard - code
variants/baseboard/include/baseboard - headers
variants/poppy - code
variants/poppy/include/variant - headers
New boards would then add themselves under their board name within
"variants" directory.
This is purely an organizational change.
BUG=b:37375693
Change-Id: If6c1c5f479cfffe768abf27495d379744104e2dc
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19322
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Clean up Kconfig file in order to support variants for poppy. Add
BOARD_GOOGLE_BASEBOARD_POPPY that can be set by various poppy variants
to use the common baseboard configs.
BUG=b:37375693
Change-Id: I399ecc8c3efb3af26e1fcf60fe2c75b24769fc0f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19321
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add camera related support
* Enable the SA Imaging Unit and CIO2 devices.
* Enable TPS68470 PMIC and populate related ACPI objects.
* Enable OV cameras and populate related ACPI objects.
* Enable Dongwoon AF DAC and populate related ACPI objects.
BUG=b:36580624
BRANCH=none
TEST=Build and boot poppy. Dump and verify that ACPI tables
have the required entries for all the camera devices.
Change-Id: Ifbe878bb6b25fc976e935fee16c4d59fadd47fe2
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18969
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This patch includes ipu.asl file in the main DSDT definition
to add ACPI entries for IMGU and CIO2 devices.
BUG=b:36580624
BRANCH=none
TEST=Build and boot poppy. Dump and verify that DSDT table
has the entries for IMGU and CIO2 devices.
Change-Id: Ib7485315cb9468da7c6aa090862657a265121493
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/19110
Tested-by: build bot (Jenkins)
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
1. Update formatting of gpio table to fit everything within 80 column
limit.
2. PEN_RESET gpio is non-existent. Get rid of it.
BUG=b:37375693
Change-Id: I1bcc4168659f365547e5f7227df8659e4bc7f243
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19320
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable lower power state when running on battery. Deep S3 is not
enabled when in AC mode to support standard "docked" config.
BUG=b:36087058,b:36723679
TEST=Verified following behavior with USB mouse:
1. If AC is connected when entering S3, USB mouse is able to wake up.
2. If AC is not connected when entering S3, USB mouse does not wake up.
3. If AC is connected when entering S3 and removed after entering S3,
USB mouse does not wake up.
4. If AC is not connected when entering S3 and attached after entering
S3, USB mouse does not wake up.
Change-Id: I141a8d4779de004e27fcd9357cef787a38a27b24
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19276
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
TPM ACPI entries are automatically generated, and the old static
TPM ASL file is obsolete. Remove the reference to this obsolete
static ASL file.
Change-Id: I3cb2a8a3ac337d1de8a3c394d7a28155597239d0
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/19283
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Commit bf264e94 (i945:) adds a PCI reset to the romstage, and commit
bc8613ec (Fix i945 based boards) fixes that to use the correct
delay of 200 ms. This code was then copied over, when adding support for
the Lenovo T60.
The reset was related to the shipped crypto card on the Roda RK886EX and
Kontron 986LCD-M, so is not needed on the Lenovo T60. So remove it, to
reduce the boot time by 200 ms.
The same change is done for the Lenovo X60 in commit 7676730b
(mb/lenovo/x60: Remove PCI reset code from romstage).
Change-Id: Ifff43f095a1236c9e9a9ef0687e8efe42e72c971
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/19298
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The HDA verb for falco/wolf's internal mic was wrong, preventing the mic
from working properly in Windows and macOS (the Linux driver overrides
the verb table, so wasn't affected). Set the verb connector/jack bits
properly, to no connector / no jack detect, in order to fix.
Also, make (2) small non-functional fixes:
On falco, NID 0x1A was being disabled twice (instead of 0x1A and 0x1B
both being disabled - copy/paste error).
On wolf, NID 0x19 was set to an internal analog mic, where it should have
been disabled (again, copy/paste error).
Both these errors were introduced when consolidating/upstreaming
and were not present in the original Chromium sources.
Test: boot Windows [8/8.1/10] and verify mic functional with Realtek
drivers on both falco and wolf.
Change-Id: I9c343dda4762f0b1f814318c155e22c59d2da8db
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19262
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Remove the 'probed' setting from the Realtek 5663 headset codec I2C
device. This was added when we had a hardware issue that was preventing
I2C operation because the clock/data lines were swapped.
With new and/or reworked hardware this is no longer a problem and we do
not want the I2C layer in the kernel to talk to the device before the
rt5663 driver.
BUG=b:35585307
BRANCH=none
TEST=Boot on Eve and verify rt5663 driver still loads properly.
Change-Id: Ice38889e8f5d3fd1307056cab10fbe3f4e197749
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19304
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
- remove old, buggy NGI code from falco/peppy variants
- remove superfluous INTEL_DP/INTEL_DDI configs, since already
selected by northbridge/haswell
- always use libgfxinit when use native init config selected
- enable NGI/libgfxinit for all slippy variants
The reset of the old Haswell NGI code will be cleaned up in
a subsequent patchset.
Test: select MAINBOARD_DO_NATIVE_VGA_INIT, observe panel init
using SeaBIOS and Tianocore payloads on peppy, wolf variants
Change-Id: Id5727cad7f714ffa57e77e2a25505e3c28f55237
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18824
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use linker instead of '#include *.c'.
The smbus_fixup() was changed not to use a structure that's defined by a
northbridge since multiple different northbridges can be used. Instead
the caller now directly passed the memory slot details.
Change-Id: Ia369ece6365accbc531736fc463c713bbc134807
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/19082
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Remove the ACPI ALS device from the EC configuration because this system
has an ALS that is presented through the new EC sensor interface rather
than the legacy ACPI interface.
BUG=b:37179776
BRANCH=none
TEST=Boot an Eve device and ensure that 'acpi-als' device is not present
in /sys/bus/iio/devices.
Change-Id: Ie18b8a661e4d16464784ca8a227586036e7631de
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19265
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Set UART0 to "PchSerialIoSkipInit" so the pins for this device are not
set back to native mode by FSP when configured as GPIO input by coreboot.
Now that FSP is not touching the pins I also removed the workaround to
reconfigure the pins after FSP.
BUG=b:35647877
BRANCH=none
TEST=Verify that GPP_C8-GPP_C11 are configured as GPIO input once the OS
is booted and they are not set back to native function by FSP.
Change-Id: Ifec4fa3e66ceeb660bad00c66bc7bd44bb457a01
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19264
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
These lines act as inputs to both EC and AP and when the corresponding
TCPC mux is in low power mode the line is floating. Add an internal
pull-down to each GPIO to prevent it from floating in this state.
BUG=b:35775012
BRANCH=none
TEST=Verify that the kernel does not see a device present on DP when
the TCPC mux is in low power mode.
Change-Id: Ie229f84871e9994467c0ab660cc7e271a51d9cbb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19263
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
With EuP and PME enabled the USB power turns off during S5.
Change-Id: I8b9fd7bb308f544401f90f8aa5ffaec61251b2b3
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/19073
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This configures GPIO_177 as native function.
This enables OS to boot from sdcard.
BUG=b:35648535
TEST=Check OS boot from sdcard.
Change-Id: I73901d4a1b39752cbc452f3286d494587dac95d4
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-on: https://review.coreboot.org/18948
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
|
|
Weida touchscreen controller needs 130 ms delay after reset
BUG=b:35586513
BRANCH=reef
TEST=Verified that touchscreen works on power-on and suspend/resume
on snappy.
Change-Id: I8418e742a69a2d6395baa2799a4da42a9bb5b312
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/19245
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
In order to support a standard "docked" config disable Deep S3 when
connected to AC power. This allows USB devices to wake the device
from suspend if it is externally powered, but still retains the
lower power state when running on battery.
BUG=b:36723679
BRANCH=none
TEST=manual testing on Eve for USB wake behavior:
1) when suspended on battery USB keyboard does not wake
2) when suspended while connected to AC a USB keyboard does wake
3) if suspended with AC, and then AC is removed, system does not
wake with USB keyboard
4) if suspended without AC, and then AC is added, system does not
wake with USB keyboard (it cannot get enabled without waking and
re-suspending)
Change-Id: I670e39d42cdb5b80612206da899be82ef3b2cbf2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19240
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable the Intel WiFi SAR feature for Eve, which will be used to
provide wifi power tables based on values read from VPD.
This is enabled based on CONFIG_CHROMEOS because it relies on the
presence of VPD code from vendorcode/google/chromeos.
BUG=b:36727652
BRANCH=none
TEST=test on Eve by setting "wifi_sar" in VPD and ensuring that
the ACPI WIFI device gets the expected "WRDS" and "EWRD" tables
with the values that were set in VPD.
Change-Id: I11c129baca891221177575108ac09ba1707b516e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19241
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Currently when enabling Deep S3 or Deep S5 it unconditionally gets enabled
in both DC and AC states. However since using Deep S3 disables some
expected features like wake-on-USB it is not always desired to enable the
same state in both modes.
To address this split the setting and add a separate config for Deep Sx in
AC and DC states.
All motherboards that set this config were updated, but there is no actual
change in behavior in this commit.
BUG=b:36723679
BRANCH=none
TEST=This commit has no runtime visible changes, I verified on Eve that the
Deep SX config registers are unchanged, and it compiles for all affected boards.
Change-Id: I590f145847785b5a7687f235304e988888fcea8a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19239
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
These lines act as inputs to both EC and AP. Thus, add internal
pull-downs to prevent them from floating.
BUG=b:35648530
Change-Id: I42326c810775d5449e99e52e81870970247ce335
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19243
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Put all configs required for enabling cr50 SPI TPM on poppy under
POPPY_USE_SPI_TPM so that it can be enabled any time for testing SPI
TPM on this board.
Also, add required callback for irq status and devicetree config for
GSPI0.
BUG=b:36873582
Change-Id: I67793093c006c1325fc16f669a96126525f83243
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19238
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Scarlet don't have eDP and MIPI driver is not ready, skipping
display for now or else Scarlet would be stuck in
reading eDP HPD because there even not power for it.
TEST=boot to kernel on Scarlet
Change-Id: I02ab4ef21bf77b98414f537aca57b46c11922348
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19237
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Due to issues with stability limit the SKU with K4EBE304EB-EGCF
memory to 1600MHz instead of 1866MHz.
BUG=b:37172778
BRANCH=none
TEST=pass stress testing on devices with this memory
Change-Id: I02af7e9c35e2c5b0b85223d58025cbd29841d973
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19227
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This is needed if one wants to use the header more than once.
Change-Id: I375d08465b6c64cd91e7563e3917764507d779ba
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19029
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Update the I2C rise/fall timings based on newly measured values
on a new board with updated pull-up resistor values.
Touchscreen: rise time 98ns, fall time 38ms
Touchpad: rise time 111ns, fall time 41ns
TPM: rise time 112ns, fall time 34ns
BUG=b:35583133
BRANCH=none
TEST=Each I2C bus frequency was verified on a scope to be ~400MHz
Change-Id: Ibb3a15fa0cc862f36c1b9c63ac7847221020c4c0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19202
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Some renamings force us to update our code:
* Scan_Ports() moved into a new package Display_Probing.
* Ports Digital[123] are called HDMI[123] now (finally!).
* `Configs_Type` became `Pipe_Configs`, `Config_Index` `Pipe_Index`.
Other noteworthy changes in libgfxinit:
* libgfxinit now knows about ports that share pins (e.g. HDMI1 and
DP1) and refuses to enable any of them if both are connected
(which is physically possible on certain ThinkPad docks).
* Major refactoring of the high-level GMA code.
Change-Id: I0ac376c6a3da997fa4a23054198819ca664b8bf0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/18770
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch cleans up the code by:
o adding necessary default definitions to Kconfig
o removing incorrect definitions from devicetree
o removing irrelevant entries from FMD file
devicetree.cb and minnow3.fmd carried over a lot of code from google/reef
which is not correct for Minnow3 hardware. Minnow3 is not intended to
boot Chrome OS and does not need Chrome related flash regions. The
erroneous code is removed.
These changes are the same as those done for leafhill in commit:
6a48923 mainboard/intel/leafhill: Clean up
This was tested by building with the new configuration and
booting to UEFI Payload
Change-Id: I620dcbcd622f9326917c74b2a38984d9e49cff2b
Signed-off-by: Brenton Dong <brenton.m.dong@intel.com>
Reviewed-on: https://review.coreboot.org/18963
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This fixes the following issues, with no functional changes:
ERROR:POINTER_LOCATION: "foo * bar" should be "foo *bar"
ERROR:SPACING: space required after that ',' (ctx:VxV)
WARNING:LONG_LINE_COMMENT: line over 80 characters
WARNING:SPACE_BEFORE_TAB: please, no space before tabs
ERROR:FUNCTION_WITHOUT_ARGS: Bad function definition
ERROR:SPACING: space prohibited before that close parenthesis ')'
WARNING:RETURN_VOID: void function return statements are not generally
useful
2 unfixed issues:
ERROR:COMPLEX_MACRO: Macros with complex values should be enclosed in
parentheses
Verified that the binary was the same before and after the changes.
Change-Id: Ie9afb50e268f4140872e39fe8bede231a43d5cc6
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/19078
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: York Yang <york.yang@intel.com>
|
|
All boards select INTEL_EDID, move it to nb folder.
Change-Id: I35f075a87f2d841856b208f9440cf41af6a3c8e6
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19086
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Linking should allow to link depending on possible future variants.
E.g. in Makefile.inc romstage-$(CONFIG_'VARIANT0') += gpio_variant0.c
etc.
Change-Id: I88b5ef8e12ac606751952a493f626e1b146e98f7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19139
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Add package options to the CPU Kconfig that may be selected by the
mainboard's Kconfig file. Stoney Ridge is available in FP4 and FT4
packages and each requires a unique binaryPI image. Default to the
correct blob used by the northbridge by looking at the CPU's package.
Also modify Gardenia to select the right package.
See the Infrastructure Roadmap for FP4 (#53555) and FT4 (#55349) for
additional details for the packages.
Original-Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Original-Reviewed-by: Marc Jones <marcj303@gmail.com>
(cherry picked from commit 7b8ed7b732b7cf5503862c5edc6537d672109aec)
Change-Id: I7bb15bc4c85c5b4d3d5a6c926c4bc346a282ef27
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/18989
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The term 'callout' has a specific meaning in AGESA, meaning
invoking the said function from AGESA / PI proper.
OemPostParams() does not fall into that category.
Change-Id: I0ad1cbf244501207af96e0ac415a5b80ced91052
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19141
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The term 'callout' has a specific meaning in AGESA, meaning
invoking the said function from AGESA / PI proper.
OemPostParams() does not fall into that category.
Change-Id: I45913d93323b3813fc35b1dd1fdca3d782d4b01f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19140
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
BUG=b:35583511
TEST=check i2c bus 0 initializes from ap console log
Change-Id: Ibb6709159f5ed28ad0b62397d2ddb504dec55167
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/19105
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Using linker instead of '#include *.c'.
Change-Id: Ie1bc538aa29c4f18dd6f31a83d3da58f196f2078
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/19081
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Even though the i2c spec has no minimum data hold time in fast
mode the trackpad vendor indicates 300ns is their minimum. However,
the topology of the board uses FET isolation to cross voltage
domains. Therefore, the default 300ns which should work isn't reflected
on the device side of the voltage isolation circuit. Therefore,
increase the data hold time to show an observed data hold time of
more than 300ns on the device side.
BUG=b:36469182
Change-Id: I1b70f2f53c5a29cc7cfd5035a71ca5811b3bcba0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19065
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
SD card detect pin is moved to GPP_E15 in the next build. Update
device tree and gpio config accordingly.
BUG=b:36012095
Change-Id: Ic0ff72cdcb0f1ca27abc7eb8da9ccd8a21b28522
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19107
Tested-by: build bot (Jenkins)
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.corp-partner.google.com>
|
|
This mainboard uses a LVDS connection for LCD panels. Apollo Lake SoC
provides a display controller with three independent pipes (1x eDP and
2x DP/HDMI). PTN3460 is an embedded DisplayPort to LVDS bridge device
that enables connectivity between an eDP source and LVDS display panel
(http://www.nxp.com/documents/data_sheet/PTN3460.pdf).
The bridge contains an On-chip Extended Display Identification Data
(EDIT) emulation for EDIT data structures.
This patch sets up PTN3460 to be used with the appropriate LCD panel.
Change-Id: Ib8fa79bb608f1842f26c1af3d7bf4bb0513fa94d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19043
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I79d4a4d1d5966ab46c8a9b9e9ca4e09e21ecfea7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18717
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I074dc7d5edbe3444f841e67a5644938e23118942
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18716
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
