Age | Commit message (Collapse) | Author |
|
Patch corrects IRQ and GPIO configuration for RT5682 codec's Jack INT.
Switching IOAPIC to GpioInt because ACPI Interrupt() doesn't support
jack triggering on both edges.
BUG=b:130180492
TEST=build and boot on a CML EVT board.
Use evtest & verify headset jack detection functions as expected.
Change-Id: Ia9bf8d554b54554f9ac1e78fd44a508964c8a14d
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Suggested-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32474
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use already defined system_reset() function.
Change-Id: I68ff4cffa2bfab6a15299795c3e1837fc9b85806
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Disable the GBB flag forcing manual recovery now that we can read
the manual recovery from H1.
Enable the GBB flag to skip EC software sync, since images built
from coreboot.org do not include the EC binaries by default.
Change-Id: I0e1d6304e3e29eda68c7b807cf0774275c37d710
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We do not want the RX signal to be floating on the board as that could
cause the ISH to remain in a higher power state (because there is logic
to keep the ISH in an higher power state when there is an active UART).
Add an internal 20K pull up on the RX line. In normal configuration this
will burn an additional 544uW.
BRANCH=R75
BUG=b:131241969
TEST=verify that ISH console still works with rework
Change-Id: Ifc9621bcafe4c86edfa9cd6d58b307254d3a81ca
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This patch adds the setting of psys_pmax to 136W. According to the
design, Rpsys is 11.8Kohm. Here is the equation to come out the
Psys_pmax value: Psys_pmax * 1.493uA/W * 11.8Kohm / 2 = 1.2V
Hence, Psys_pmax is 136W.
BUG=b:124792558
BRANCH=None
TEST=emerge-sarien coreboot chromeos-bootimage & Ensure the value is
passed to FSP by enabling FSP log & Boot into the OS
Change-Id: Id3f6be5f0c2346a7763195a992c0ae45faede056
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
The ACPI code of LPE device is included regardless of the
availability of the LPE controller.
Linux remains requesting the status of device LPEA even if
this device is disabled.
Include ACPI LPE controller code at Braswell mainboards with
LPE enabled.
BUG=N/A
TEST=Linux 4.17+ on Portwell PQ7-M107
Change-Id: Ic8acf9ea9e9b0ba9b272e20beb2023b7a4716a73
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
The dqs_map array is used only for LPDDR3 and LPDDR4. It is not used for
DDR4, and so it can be removed from the baseboard memory initialization
code.
BRANCH=none
BUG=b:129706819
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Change-Id: I07fac3097d68f37b4630d3f0010f987da2f03bd7
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32484
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
First configuration supported is 8 GB system memory:
4 x 2 GB (K4E6E304ED-EGCG).
BRANCH=none
BUG=b:129706819
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: Ibd92d585118ff75492e8a7188dcdb2a286836d56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Changes includes:
- enable TPM1 + add entry in devicetree
- configure LPC IO to make IPMI work + add entry in devicetree
- introduce DSDT and SMBIOS entries for IPMI to make it detectable
by ipmi_si driver
Signed-off-by: Lukasz Siudut <lsiudut@fb.com>
Change-Id: Ia975643064075f1f861f4ead6f24ed71f345ea04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Enable LTR for NVMe so it can use ASPM L1.2.
BUG=b:127593309
TEST=build and boot on sarien and check L1 substate with lspci
before: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2- ASPM_L1.1+
after: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
Change-Id: I9842beda6767f758556747f83cfcedbd00612698
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
|
|
This reverts commit 77fb3632a4a3d3004b3aa4950967be9164d9711d.
Reason for revert: This change inadvertently added a submodule.
Change-Id: I6cc2a3cd9d88986a2599a5ff2e5a066b1396a8c0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32472
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch revises the AC/DC loadline settings because some major
layout changes between proto and evt boards.
BUG=b:130740639
BRANCH=None
TEST=emerge-atlas coreboot chromeos-bootimage and boot to the OS.
Change-Id: Iea12c621e7fab427a0de8f43f0290bf01d0c5a09
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: caveh jalali <caveh@chromium.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
|
|
Add FP_RST_ODL to early GPIO table, configured as low, so that the FPMCU
will get reset when coreboot enters bootblock.
BUG=b:130229952
BRANCH=none
TEST=Compiles (no Hatch device w/FP to test)
Change-Id: I8a8d8cc2c560f6518337f7500575fdc2265b6347
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Lynx Point switched to doing mainboard-specific super I/O setup in the
bootblock with commit d893a2635fdd ("sb/intel/lynxpoint: Enable LPC/SIO
setup in bootblock"). The X10SLM+-F was added while that commit was in
review, and hence did not receive the necessary changes to SIO setup.
This patch has not been tested on hardware.
Change-Id: I7a648ec967dea2113cbbde1a93c1963ca6dd3c88
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
On EC end, we want to change this pin from push-pull to open-drain.
And since there is no external pull-up resistor on the board, we'll
have to configure this pin as internal-pull-up on AP end.
BUG=b:129306003
TEST=None
Change-Id: Ibc1f89fc25773220db009c6571400b01390dd756
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add common SoC config.
Disable PCIe WiFi.
Add digitizer.
Turn off native SD card interface.
No WWAN.
Add DA7219 driver to Kconfig.
BUG=b:130310626
BRANCH=none
TEST=compiles (no Hatch ref or Kohaku device to test)
Change-Id: I17d5ba6ce4ec412384e4a1678474b8d26499ba40
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Not all Hatch variants utilize the SoC's native SD card support. Move
the support to board-specific variants instead of the base device tree.
BUG=none
BRANCH=none
TEST=compiles (no Hatch device to test with)
Change-Id: Iae24114aad2c4d042c25da6f8cb740ccc8960082
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32417
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Similar to hatch(CB:32278), this change sets SerialIo
config for UART0 to PchSerialIoSkipInit to skip initialization in
FSP.
This change also adds a device to kohaku override tree to ensure that
the settings in it take effect.
BUG=b:130310626
Change-Id: Ia25b45811be26d55fc0019e4cd22eb7310b5a4c4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Enable acoustic noise mitgation for arcada platform,
the slow slew rates for Ia and Gt are fast time dived by 8.
BUG=b:131144464
TEST=waveform test and hardware validation result pass.
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Change-Id: I37315ecfa245fce3085e62d1566ff037d8aa8ab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32403
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable the POWER_OFF_ON_CR50_UPDATE option on sarien/arcada. This is
needed so that platform properly boots after doing a Cr50 firmware
update when running on battery.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I0b687285eb95070eaffb68611a7d98eb8434ce2c
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Sarien during S0iX
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I48419132ba734f20ad5cf484c2dda609570a6dd0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32330
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sarien will change Melfas from HID to I2C and change address from
0x10 to 0x34. So we don't need VPD to separate Elan and Melfas
anymore.
BUG=b:131194574
TEST=boot up and check no Melfas HID device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic002f61b226743e1c18dbdbc51ce8b733916d8a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32437
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We want to disable touch for non-touch sku. We can use
strap pin GPP_B4 to identify it is connected with touch
or not.
touch sku: GPP_B4 is low
non-touch sku: GPP_B4 is high
BUG=b:131132419
TEST=boot up and check no touch device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If6681262c25e4b01e061a8520e38905d40345509
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32438
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SSD reset pin had been added on DVT2, the power sequnence requires
toggle in boot stage.
BUG=b:130741066
TEST=Boot up with simulated DVT2 platform and confirm SSD can be
detected during warm reboot.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie734875a49b8b61f8b813c473d30cbcaf4dd13d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32434
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tune I2C params for I2C buses 5, 6, and 7 to ensure that the
frequency does not exceed 400KHz.
BUG=b:131132499, b:128998988
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage and measured frequency
under 400 KHz
Change-Id: Ie8cfba72a0654402ccb0274c00b44fbfa2deea21
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add goodix touchscreen support
BUG=b:131082228
BRANCH=octopus
TEST=emerge-octopus coreboot and verify that touchscreen works on
bloog.
Change-Id: I0b3b481ca806b6452d67ace5dfe53f12a14ac3be
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This allows for serial console during the bootblock and enables
console in general for the bootblock.
Change-Id: I5c6e107c267a7acb5bf9cbeb54eb5361af3b6db4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30315
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Arcada during S0iX
Change-Id: I4b8f3fdc0d107b080c5febe6fa5d29ea5d1ed0fc
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Include pch.h in the source files instead in sandybridge.h.
Tested on Lenovo T520 (Intel Sandy Bridge).
Still boots to OS, no errors visible in dmesg.
Change-Id: I9e5b678e979a8d136d8d00b49486d0a882f77d81
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: Ib843eb7144b7dc2932931b9e8f3f1d816bcc1e1a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/26796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: David Guckian
|
|
Change-Id: Iddba5b03fc554a6edc4b26458d834e47958a6b08
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: David Guckian
|
|
Change-Id: Ie21c390ab04adb5b05d5f9760d227d2a175ccb56
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The pci_or_configx function makes the code shorter and more readable.
Change-Id: Ic1ba250f8ac9fb75cf3252aec18af80842bda7dd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32310
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Droid/Blorb supports keyboard backlight feature, so enable the ASL code.
BUG=b:130330141
BRANCH=octopus
TEST=Build and boot to OS, verify that the string 'KBLT' is in the DSDT.
Change-Id: I74684e3905d34b61fa4b851798dbca018f986e5a
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
When the components like LCM ID are not installed (i.e., NC), ADC will
return some value with much larger variation from standard value (out of
the tolerance we set). To support that, we should check tolerance only
on non-NC voltages.
Also improve the error messages so we can see the ADC raw values
instead of simple assertion error (which makes debugging more difficult
since we have to build another firmware image just to print the values).
BUG=None
TEST=Booted on Kukui and got correct SKU ID for NC LCMID.
BRANCH=None
Change-Id: I8d00956e0e3b48ddbcaa505dd3ade24720c3b4ad
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32353
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, Arcada only supports D3hot during S0iX and there is leakage
power around 5~10mW depending on SSD vendors.
To support D3cold for SSD during S0iX, one MOSFET will be added on DVT2
and two GPIOs are required to be configured.
GPP_H13 is to control SSD_SCP_PWR_EN(power enable) and GPP_H12 is to
control SSD reset.
BUG=b:130741066
TEST=Measure SSD power during S0iX from Arcada(DVT2)
Change-Id: I868590e9e85d5df07930a3681884e3fc3a5c4d50
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32361
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Previously Haswell used a romcc bootblock and starting verstage in
romstage was madatory but with C_ENVIRONMENT_BOOTBLOCK it is also
possible to have a separate verstage.
This selects using a separate verstage by default but still keeps the
option around to use verstage in romstage.
Also make sure mrc.bin is only added to the COREBOOT fmap region as it
requires to be run at a specific offset. This means that coreboot will
have to jump from a RW region to the RO region for that binary and
back to that RW region after that binary is done initializing the
memory.
Change-Id: I3b7b29f4a24c0fb830ff76fe31a35b6afcae4e67
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/26926
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ia4b7311f30f8ec951d02d3c31c30cf8895ed0eb2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
I2C 1 is not being used in any of the octopus variants, so disable it.
BUG=none
BRANCH=octopus
TEST=Verify on meep and bloog
reboot and s0ix suspend successfully
Change-Id: I7ed5065cfd0b9780d13feb27cc78b8090d7a03a6
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
arcada is designed to operate at max power of 140 Watt. Hence set psys_max to 140W.
BUG=b:124792558
TEST=Build and boot arcada.
Change-Id: I280dfb81b3e25c7619a68db487e2b18867f52fda
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
References to MAINBOARD_PCI_SUBSYSTEM_{DEVICE_ID,VENDOR_ID} were removed
in commits
dbd3132 sb/intel/{i82801g/i/j,bd82x6x}: Make use of generic set_subsystem()
00bb441 sb/intel/lynxpoint: Remove PCI bridge function
Change-Id: I72bba8406eea4a264e36cc9bcf467cf5cfbed379
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32107
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ensure Kohaku GPIO pins are configured correctly w/r/t Hatch. Implement the
base/override model for GPIOs (regular and early). The 'hatch' baseboard
contains the base GPIOs, and variants can override individual pads.
BUG=b:129707481
BRANCH=none
TEST=Compiles for all variants.
Change-Id: Ie5c83a0538d367ea11e9499f21cea41891d7a78e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Match SMBIOS type 17 device locator with motherboard silk screen,using
"DIMM-A" and "DIMM-B" instead of "Channel-0-DIMM-0" and
"Chaneel-1-DIMM-0".
TEST=Boot up with sarien platform and run dmidecode to check SMBIOS
type 17 have expected output.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie2125c0381bd24d96f725f68cde93a53da8c94c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
GPIO pin GPP_C23 is used as level trigger but not edge trigger, also it
is not inverted, correct it here. According to board schematic, GPP_C23
connected with 3.3v pull up, so the pin is low active.
BUG=b:128554235
TEST=Boot up arcada platform with stylus keep on touching the screen,
the touch screen is still functional once in OS stage. Without change,
touch screen is not functional at same scenario.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I2bee664198057e3997dda181a16b9a0388067036
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32347
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable the Kconfig option to automatically read the board ID
and populate it into the SMBIOS tables.
BUG=b:123261132
TEST=verify current board id from the OS:
cat /sys/class/dmi/id/board_version
rev1
Change-Id: Id41631bfaa627ca9d5034e2ebe93f8ace2ffdad8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32277
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set default configuration to low for gpio_178, and can remove the
override setting for bobba/bloog/fleex/meep/phaser.
For ampton, Change-Id I64a67f73564188ad0548a1a770169ef2bca47453 (
mb/google/ampton: Fix polarity of EN_PP3300_WLAN_L signal.)
modified the pin setting.
TEST=verified that boot into OS on meep board.
suspend/resume, reboot, and no failure found.
Change-Id: I7668ff4817edfca5c6cea63db779fcea21c7af92
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32247
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Write protection (get_write_protect_state) was hard-coded to 0 and
should be fixed to read from correct GPIO (PERIPHERAL_EN0 from
schematics).
BUG=b:130681408
TEST=make -j; boots on Kukui Rev2.
BRANCH=None
Change-Id: I75b98b1d587abe5e8cdf3df28ea661bc1ffa19f9
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-by: Joel Kitching <kitching@google.com>
|
|
Change VmxEnable UPD values based on Kconfig ENABLE_VMX
and remove it from Devicetree and chip.h
Remove Vmx dependency on Vt-d
Change-Id: I4180c2270038a28befd6ed53c9485905025a15ba
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32117
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Kukui is using MIPI display panel and needs some identifier to tell
payloads which LCD module is installed, and to select right kernel
device tree. Following Scarlet, the decision is to embed LCD module ID
as part of SKU ID.
The LCM ID is using a different voltage mapping table from the rest.
Considering the complexity in computation of SKU ID, it is better to
move the cache logic from get_index to caller.
Also revise the mapping table since ADC on 8183 only supports 12
levels.
BUG=b:129299873
TEST=make -j; boots on Kukui Rev2 unit.
Change-Id: Ib0c00bc8ce3c71c445c5c4561403ce8ef4dd5844
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32263
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The external RTC was removed on the mainboard as it is not needed.
Remove the usage of the driver for RX6110SA as well.
Change-Id: Ia476e58c0b0f343d4e9e4fa6039bf82b194a87d3
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
|
|
With commit
'4074ce0cc7 (intel/apollolake: Add HDA to disable_dev function)'
FSP is now requested to switch off HDA PCI device if it is disabled in
devicetree. Doing so results in a warm restart. Normally this event
will be stored in CMOS RAM (if the descriptor is configured to do so)
and therefore no further resets are requested by FSP on the next boots
as long as CMOS RAM is kept alive.
The Siemens mainboards based on Apollo Lake do not have a CMOS battery
and therefore the CMOS is not backed up. This leads to reset requests
from FSP after PCI enumeration on every boot. To avoid this reset enable
HDA in devicetree for these mainboards. Though we do not have any usage
of HDA it should not be an issue that the HDA device is now enabled. The
benefit is though that no reset is requested anymore by FSP.
Change-Id: I637c7c01d73350700c6066fee74fecbb5b93b221
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32295
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on the power rail discharge times measured on hatch,
update the assertions widths that have to be programmed in SoC.
BUG=b:129328209
TEST=warm/cold reboot and S3 are working fine on hatch.
Change-Id: I3c6dce0a942e6dcd9e55ef5e58a7e9e8d2b0a1e3
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32266
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Laser would prefer to use different SAR values. Since Laser
sku id is 5.
BUG=b:130381493
BRANCH=octopus
TEST=build
Change-Id: I5cce38a191edfb235e274db3c788c58b65e0ebe1
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32296
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use common code to detect ACPI S3.
Tested on Thinkpad X60.
Change-Id: Ia759a9ed141efc8130860300f2a8961f0c084d70
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Use common code to detect ACPI S3.
Untested.
Change-Id: I2264c087b317f70506817b5458295a17e83b1efc
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32038
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Restore Goodix devicetree config because of the
missing Goodix config when moving from baseboard
devicetree to board level overridetree. And move
PENH from I2C#2 to I2C#1.
BUG=b:124460799
BRANCH=None
TEST=local build and tested with Goodix touch screen
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic028c5d7b687a069d7f0510897bea91dca58e91f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change uses GPIO IRQ instead of IOAPIC for GPP_A0 pad which is
the interrupt line for sx9310. This is required because IRQ# used by
GPP_A0 is allocated for PIRQ which does not allow IRQ# sharing.
Additionally, this change also configures GPP_A6 for GPIO IRQ. GPP_A6
is currently unused in the devicetree.
BUG=b:129794308
TEST=Verified that there are no interrupt storms on GPP_A0.
Change-Id: Ibb510a647391c0d9cb854d23656bb4b1cb7756ab
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This change configures reset config for all pads routed to IOAPIC as
PLTRST. This is required to ensure that the internal logic of the GPIO
gets reset any time the platform enters S3 or powers off and avoids
any interrupt storms on boot-up.
BUG=b:129933011
TEST=Verified that there are no interrupt storms on boot-up from S5.
Change-Id: Ib790280c9f1410fa18746d4d7d2a5027afd7585b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
UART0 is already configured in coreboot, so this change sets SerialIo
config for UART0 to PchSerialIoSkipInit to skip initialization in FSP.
BUG=b:130325418
Change-Id: Ifc88f4fa11bff2144417d5194776c15f9f7b60ac
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Adds virtual logical devices numbers for the Nuvoton (NCT6791D)
SuperIO to the devicetree.
Change-Id: I7df1633951c30fef14c62c89aaedebd3044b312f
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add the new configuration 'Krane' that will need at least its own EC.
There's currently no difference in coreboot side.
BUG=b:130011505
TEST=make menuconfig; make -j # select board=Krane
BRANCH=None
Change-Id: Ibb2ec42b08f9a51b22c22f3fe99b203f5eb31627
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Based on HW change, reserve gpio pins for D3 cold control.
A13,A15 for Card reader
H13 for M.2 SSD
BUG=b:123263562
TEST=N/A
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib4245be8d77c015e56df7b1d53ef82722c51d656
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Three GPIOs are not being used and this change will save 2-3mW
power during S0iX and this power saving is only for Arcada
BUG=b:129990365
TEST= Measure total platform power during S0iX from Arcada
Change-Id: Ie0208bd6c7affb2e87fd76005b727ea7effdf434
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
WiFi enable signal was configured and driven as active-high, but the signal is |To start the server in this Emacs process, stop the existing
actually active-low
BUG=b:130196983
BRANCH=none
TEST=Verified WiFi still works after boot, and also after a suspend/resume cycle. Device powers down correctly using "poweroff".
Change-Id: I64a67f73564188ad0548a1a770169ef2bca47453
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32255
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The "write protect" GPIO's cached value is never actually
read after entering depthcharge. Ensure the value from
get_write_protect_state() is being transferred accurately,
so that we may read this GPIO value in depthcharge without
resampling.
The cached value of the "recovery" GPIO is read only on certain
boards which have a physical recovery switch. Correct some of
the values sent to boards which presumably never read the
previously incorrect value. Most of these inaccuracies are from
non-inverted values on ACTIVE_LOW GPIOs.
BUG=b:124141368, b:124192753, chromium:950273
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ic17a98768703d7098480a9233b752fe5b201bd51
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
For Kukui CR50_IRQ pin, we're going to replace external pull-up with
internal pull-up. This change won't break older boards, so we can just
always do that when setting up GPIOs.
BUG=b:124821269
BRANCH=none
TEST=Waveform looks correct.
Change-Id: Ib1a90dce583a6aa0cec8ac8ba96d1362f50c16a8
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
ODM reported issues that some systems can't be shutdown to S5 very
occasionally.
ODM found issue is gone if they remove the WLAN card.
So, this change to disable WLAN before system enters S5.
This change is validated by ODM and it does help issue.
BUG=b:129377927
Change-Id: Ib8e81022b8c9b63bc75e5cc14121233222da7595
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32246
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Chen Wisley <wisley.chen@quantatw.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I6095c3b30990b530c5bc4e2c808879252680e1d7
Signed-off-by: Andrea Barberio <barberio@fb.com>
Signed-off-by: David Hendricks <dhendrix@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
This pin should be set to its alternative function SRCLKENA0 instead of
GPIO, so that SPM (a power management component of MT8183) can control
it.
BUG=b:113367227
BRANCH=none
TEST=1. Boot. Run 'powerinfo' in EC console and see power state in S0.
2. Run 'powerd_dbus_suspend --wakeup_timeout=10', and then
run 'powerinfo' in EC console and see power state in S3.
3. Wait until AP resume.
4. Run 'powerinfo' in EC console and see power state back to S0.
Change-Id: I0a7e34f95381dec17eb6d166d6552c12e021bd9a
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32120
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a fmd file for 16MiB fmap, so that we can support
both 16MiB / 32MiB SPI flash ROM chips.
BUG=b:129464811
TEST=build hatch firmware image with 16MiB fmap and
verify fmap is updated by 'fuility dump_fmap'
Change-Id: Ifc0103c7fd0d99439f40a31d23422401a6dce826
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Expose the Bluetooth BT_DISABLE_L signal in Hatch's devicetree,
on both USB2 port 5 and 10.
BUG=b:123293169
BRANCH=none
TEST=compiles, verified kernel is able to find the reset-gpio
Change-Id: I6e4d9786e44f12da71533b6740fdd390f3a57e40
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32216
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ief1eaab960c8fdab5bd5041b1a4f0c6ba1dd833f
Signed-off-by: David Hendricks <dhendrix@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32222
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Another run of
find src/ -type f | xargs sed -i -e 's/IS_ENABLED\s*(CONFIG_/CONFIG(/g'
Change-Id: I3243197ab852a3fbc3eb2e2e782966a350b78af2
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The dev pointers were being dereferenced before the null
check. Move the checks so they are done earlier.
Found-by: Coverity Scan, CID 1241851 (REVERSE_INULL)
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: Ie578787c3c26a1f3acb4567c135486667e88a888
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
There is no device on I2C0 which requires a lower clock rate.
Change-Id: Iaf01be5ea4839c54eb2f0ba95bca272970c24bdb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Set new tcc_offset value to 10 degree C. This configures the Thermal
Control Circuit (TCC) activation value to 90 degree C. It prevents
any abrupt thermal shutdown while running heavy workload. This helps
to take early thermal throttling action when CPU temperature goes
above 90 degree C.
Change-Id: Ica77264782b4a3f3e72e73e1b8cb8b2e464fb033
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add a support melfas touch panel with i2c address:0x34.
BUG=b:122019253
TEST=tested with new melfas touch panel and worked
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I27f5c47517d093c819cbbbcdafd85d74145887e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32169
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I23bc0191ca8fcd88364e5c08be7c90195019e399
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: David Guckian
|
|
Change-Id: I020c1b9558f6aec47b048fa575c64c619b8c592a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32013
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds support PCIe Gen 3 with 8GT/s link speed for PEG x16
slot. All parameters for FSP are set during initialization in
romstage. Now there is no need to additionally configure the FSP
before building the ROM image.
Tested on Intel Core i5-6600 processor with the following devices:
- LP11000e Fibre Channel HBA (Gen2 x8);
- PEX8734 PCIe Fabric/Switch (Gen3 x16);
- NVIDIA GeForce GTX 1060 GPU (Gen3 x16).
GPU works with an nouveau and proprietary driver under Ubuntu 18.04.2
(4.15.0-46-generic GNU/Linux kernel). Discrete graphic card is used
as primary device for display output. Dynamic switching is not yet
supported.
Tianocore (edk2-stable201811-216-g51be9d0) is used as the payload.
Change-Id: Ia4f29df47d76de5069fe53120434cc7c2ab6f044
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31948
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If an external graphics card is inserted in the PEG, it will be used
as the primary display device (as in the AMI BIOS)
Change-Id: Iea846179fc309c2b98093de37c05ceb332081f4f
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The InternalGfx option in devicetree.cb is not used to enable iGPU.
The patch removes this option from chip.h and mb/*/devicetree.cb
files for all boards with skl/kbl processor.
Change-Id: I41ecca3fdfb1d4b20ee634a13263ff481dcf440e
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This change moves the I2C/SPI devices and configs which do not apply
to all variants to override tree. Currently, there are just two
variants. However, as we prepare to add more variants, these devices
need to be moved out of the base devicetree.
BUG=b:129728235
TEST=Verified that I2C/SPI devices are present in static.c for hatch
and hatch_whl.
Change-Id: I9426f6bf5f8514de5f1889e22e57105749fd92de
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32138
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In S3 the PCH is driving the DEVSLP signal low, assuming that the SATA device
is already powered off. However on hatch the SATA power is still enabled. And,
since DEVSLP is low, this causes the SATA device to not enter low power state.
The fix here is to set the pad config to be reset on PLTRST assertion which
will cause the pin to be high impedance state and will be pulled up by the
SATA device.
BUG=b:126611255
BRANCH=None
TEST=Make sure that S3 and S0ix is working fine on hatch.
And also make sure that DEVSLP is pulled high in S3.
Change-Id: Ifb6a71a72244522c8dd8d48e9b9f8dc6feef8981
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch provides a clock on Pin PMU_SUSCLK. This is necessary for correct
function of the SMARC module.
Test=mc_apl4 flashed, booted into Linux, ckecked CLK with scope
Change-Id: Ieb1d66b5a09363c9bed2b19e7a204f206ee04158
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32168
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set GPP_B4 to low in S5 to meet touch panel power sequence
BUG=b:124197348
BRANCH=master
TEST=Verify GPP_B4 is low.
Change-Id: I65deb33a45fdc0c0ce64deaa29c2790029dc1d12
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch configures FSP UPD values for HPD and DDC of DDI ports for
CMLRVP.
BUG=none
TEST= Tested that eDP works on CMLRVP.
Change-Id: If8c8480eaf2d63cec0b5598b5af3088c630dd78a
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32140
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adding Kohaku as a variant of hatch.
BUG=b:129706980
BRANCH=NONE
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
make sure HATCH_KOHAKU is built as well.
Change-Id: I5b451f421f6d353005e6b73eac180dcec2e8b0c0
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Creating Kohaku hatch variant. Currently taking a copy of the hatch
variant. Kohaku-specific changes to come in future CLs.
BUG=b:129706980
BRANCH=NONE
TEST=NONE
Change-Id: Ib4b8c2c8332910d992549e3aae8e6aff5234698b
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32160
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This option is duplicated in depthcharge:
https://crrev.com/c/1545144
BUG=b:124141368, b:124192753, chromium:943150
TEST=make clean && make test-abuild
CQ-DEPEND=CL:1545144
BRANCH=none
Change-Id: I48e20ad21cdcb948a23387d3e5fcf142723b0c82
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Enable Goodix touch screen.
Follow GT7375P_Datasheet_Rev.0.1
BUG=b:124460799
BRANCH=None
TEST=local build and tested with Goodix touch screen
Change-Id: Ib204e6b77b87ba6c775cf38e572476dd9eb37d1d
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32134
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow thermal table for second tunning.
BUG=b:129509918
TEST=Built and tested on sarien system
Change-Id: I64844b84891dc3ab7abe9378cdca5dcf57b3e433
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
The sku ids are updated for Pantheon.
Sync'ing the sku_ids list in the master sku sheet for Pantheon.
BUG=b:121207221
BRANCH=firmware-nami-10775.B
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: Ibf683ca8219b2980ea9d9c40b06db264d58440b0
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
|
|
For HW require to change GPIO_E1.
Change GOIO_E1 setting from NF2(SATAGP1) to NF1(SATAPCIE1).
BUG=b:123730924
TEST=flash BIOS and make sure hatch boots up properly
Change-Id: I0f5569e13b17a2dc713be5031a63436e8f31f911
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32099
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPP_A12 has a Native3 (SX_EXIT_HOLDOFF#) mode, which allows to delay
resuming to S0. If this pad is not locked and platform was not initially
designed for this functionality, malware could reconfigure this pads
setting under OS (switch to Native3), which would make platform not able
to resume until G3 is applied. To prevent misuse of this pad,
re-configure this pad before entering S3 and S5 to guarantee that the
pad configuration is correct.
BUG=b:128686027
Change-Id: I1e7979baa491acf2c56d223afb4618f0f6429e37
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I790303a1fab64dbbe749563325394b9be2c109ad
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The dead_code() macro can be used to ensure that a certain code path is
compile-time eliminated (e.g. if you want to make sure it's never
executed for certain Kconfig combinations). Unfortunately, the current
implementation via __attribute__((error)) hits only at the GCC level.
This can catch code that can be compile-time eliminated based on state
within the same file, but it cannot be used in cases where a certain
library function is built but then garbage collected at link time.
This patch improves the macro by relying solely on the linker finding an
undefined reference. Unfortunately this makes the error message a little
less expressive (can no longer pass a custom string), but it is still
readable and one can add code comments next to the assertion to
elaborate further if necessary
Change-Id: I63399dc484e2150d8c027bc0256d9285e471f7cc
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32113
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add bluetooth Rfkill function to recover the Bluetooth controller in
cases where itself has entered a bad state and needs to be recovered.
Bug=b:129375810
TEST=Boot up into OS and dump SSDT table, check there's _DSD entry under
Bluetooth devices with GPIO in. Also confirm bluetooth itself is
functional.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I79a310a55d94d7d20d1705afc11fe47cbb81abc1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
GPP_A12 is being used as FPMCU_RST in hatch. This GPIO is being padlocked in
FSP and cannot used in kernel. Hence unlock the GPIO pads to export this pin
in kernel to be used as FPMCU_RST.
BUG=b:128686027
BRANCH=None
TEST=Read Pad Configuration Lock (PADCFGLOCK_GPP_A_0) register.
localhost /sys/class/gpio # iotools mmio_read32 0xfd6e0080
0x00000000
localhost /sys/class/gpio # echo 212 > export
Change-Id: Ie0439956e6c8e386435e535665ccaf2ab82adeb0
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32126
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select support in Kconfig and configure device in devicetree
Tested with ASUS addon TPM modules, v1.2 (ASUS TPM-L FW3.19 rev1.02H) and v2.0 (ASUS TPM-L R2.0 rev1.00) using SeaBIOS and Linux OS
Change-Id: Icdad9a41b61221b536f2ac695f44319f6b0599e7
Signed-off-by: Simon Newton <simon.newton@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|