Age | Commit message (Collapse) | Author |
|
Use the 96 character limit for pad macros.
Change-Id: I03fd2f9309c04628c46e3473bed280edc57e215c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44470
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
GPIO Driver mode is used for configuration interrupt routing for
external devices through GPI. But there is no point in configuring
this for GPO. This patch replaces the PAD_CFG_GPO_GPIO_DRIVER macro
with others that do not set the corresponding bit in the Host Software
Pad Ownership register.
Change-Id: I406a08e526a6c655f38e4c0a355957c98e93881c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Add sc7180 display hardware pipeline programming support
and invoke the display initialization from soc_init.
Changes in V1:
- added display init required check.
- added edid read function using i2c communication.
- added sn65dsi86 bridge driver to init bridge.
- moved display initialization to mainboard file.
Changes in V2:
- moved diplay init sequence to mainboard file
- moved edid read function to bridge driver.
- calculated timing paramters using edid parameters.
- removed command mode config code.
- moved bridge driver to drivers/ti.
- seperated out bridge and soc code with mainboard file as interface.
Changes in V3:
- add GPIO selection at runtime based on boardid.
- add vbif register struct overlay.
Changes in V4:
- update gpio config for lazor board.
Change-Id: I7d5e3f1781c48759553243abeb3d694f76cd008e
Signed-off-by: Vinod Polimera <vpolimer@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add sn65dsi86 bridge driver to enable the eDP bridge.
Datasheet used : https://www.ti.com/lit/ds/sllseh2b/sllseh2b.pdf
Changes in V1:
- fix the dp lanes using mask
- separate out the refclk and hpd config to init function
Change-Id: I36a68f3241f0ba316c261a73c2f6d30fe6c3ccdc
Signed-off-by: Vinod Polimera <vpolimer@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Configure GPIO pins as I2S mode for audio speaker.
The audio speaker does not work on Trogdor revision 1, as the
layout was changed.
Developer/Reviewer reference, be aware of this issue:
https://partnerissuetracker.corp.google.com/issues/146533652
Change-Id: Ia4bbfea591a3231640b53e64f0e4e9d43c4437a3
Signed-off-by: vsujithk <vsujithk@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add memory parts and generate DRAM IDs for trondo.
BUG=None
TEST=FW_NAME=trondo emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I2e89ecaf73a30595ed48ac9ce94ccbd4bb7ed3c2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45164
Reviewed-by: Michael Niewöhner
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new memory.c to support DDR4 memory types.
Use the new meminit_ddr() and variant_memory_sku() for eldrid variant
code on memory.c
The initial settings override the baseboard from volteer and fine tune
gpio.c and overridetree.cb on eldrid's configuration.
BUG=b:161772961
TEST='emerge-volteer coreboot chromeos-bootimage' and verify that Eldrid
can boots. NOTE that tests the ddr4 side of the implementation.
Change-Id: I2c7b30093a8d85bac5aba5b83768af5eb36c4f70
Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
The console is initialized before mainboard_init, so the peripheral
should be initialized in bootblock_mainboard_early_init rather than
bootblock_mainboard_init.
Change-Id: I9f4ba29798eb0b1efea76f5ade4a234fb35a2f83
Signed-off-by: Sam Lewis <sam.vr.lewis@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Allow comments prefixed with '#' in mem_parts_used csv file.
BUG=None
TEST=Run gen_part_id with mem_parts_used file containing comments
Change-Id: Ia9e274d45aa06dea7a3a5f8cd1c8ee2b23398876
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The three Intel Apollo Lake boards (apl_rvp, leafhill and minnow3) do
not define MAX_CPUS, which would then default to 1. Since this is most
likely an oversight, use the same value as other Apollo Lake boards.
To ensure this does not happen again, factor out MAX_CPUS to SoC scope.
Change-Id: I5ed98a6b592c8010b59eca7ff773ae1ccc4cd7b1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45144
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
APL does not support Hyper-Threading, and has at most four CPU cores.
Change-Id: Ib2ffadc0c31cdd96bec8eed5364c984acb2e1250
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45143
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Both Gemini Lake boards in the tree use the same value.
Change-Id: Ib6bd05206026736fd7e3d44b49e4d8ba217c2708
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
For consistency with other platforms, use `SOC_INTEL_GEMINILAKE`.
Change-Id: I06310e5a9bca6c9504f19a6c2fe9b26626f290d4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Update critical and passive policy for TSR0.
BUG=b:167477885
BRANCH=puff
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I244e1b5cacabf5b73c47b4039ae150cd17fcd0fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45169
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sushi is not a real product, just a test of the new_variant program.
The effort to keep it up-to-date with the rest of Hatch is no longer
worth it. Remove the variant.
BUG=b:168030592
TEST=build bot is successful, hatch-cq builds successfully
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: I2b0036f3cbdea4bfaed1274ab87a20d24c75de57
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
CB:44774 introduced the non-existent SPD path. This is preventing the
device from booting up.
BUG=b:168053219
TEST=Build and boot drawcia board to OS.
Change-Id: I70ca5f4cf2c8e2e88ea5b1514b656caafb732743
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Tested=On OCP Delta Lake, with FSP WW36 dmidecode -t 11 can see the
SPD register vendor ID
String 7: b300 0000 b300 0000 b300 0000 b300 0000 b300 0000 b300 0000
Change-Id: I15ab9b4c709eb97a03d6e08fe0bcdcb7f8607db0
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
To minimize the quirks the kernel has to apply, the headset mic is set
to its correct value in coreboot.
Tested on lemp9, audio is functional.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I6b59de95f01360a5f7779f87f39edeb75dedc215
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43631
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ibe8844db74b43009e7c49df78882ed76b0bbebae
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ie084f93998dc16450bb3db99d7240905bed3d50e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:162232776
TEST=Measured the I2C bus frequency as 389 KHz, high time as 870 ns and
low time as 1580 ns.
Change-Id: I67d2725a7fc8d83e3fa8a56cfa86540c4e6f0971
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45084
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:163743035
TEST=Measured the I2C bus frequency as 384 KHz, high time as 924 ns and
low time as 1680 ns.
Change-Id: I60a5f6814fb9818c724f6b6fe465ea49d0de0f97
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45083
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PRM does not describe the relevant bits, but Linux's i915 driver
handles these bits the same way for both Ironlake and Sandy Bridge.
Change-Id: Ice7412e335752bd7e297ad50f685effcefbd41d2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
All boards currently have backlight on either LVDS or eDP.
Change-Id: I878bc7f1ff75a2b82b9556e855aff1d4d03e0268
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The corresponding bits in PP_ON_DELAYS are reserved MBZ.
Change-Id: Icd2554c928a5908dfb354b81d3e6c5b5f242f1d1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45034
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The corresponding bits in PP_ON_DELAYS are reserved MBZ.
Change-Id: I9789a7d50c4bce2ccad0bf476f877db25e3ff82e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Configure eldrid to use CSE Lite.
BUG=b:158140797
TEST=cd to volteer's asset_generation folder, execute
"./gen_all_variant_images.sh" and verify that all variant
images are produced.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I357abdac4102f358d3aa1cb50f600312039ef140
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
For Volteer (and future Tiger Lake boards) we can enable mode S0i3.4
only if we know that the Cr50 is generating 100us interrupt pulses.
We have to do so, because the SoC is not guaranteed to detect pulses
shorter than 100us in S0i3.4 substate.
A new Kconfig setting CR50_USE_LONG_INTERRUPT_PULSES controls new code
running in verstage, which will program a new Cr50 register, provided
that Cr50 firmware is new enough to support the register.
This CL adds code to detect the case when Cr50 is unable to generate
longer pulses, and in that case explicitly disable the S0i3.4 substate
as well as setting gpio_pm_override to all zeroes. This will increase
power usage slightly, but guarantee that the GPIO block in the SoC
does not switch to a slower sampling clock. In practice, this case
will only be encountered in the factory, before the Cr50 chip is
updated to a new RW image.
(Prior to this change, the gpio_pm_override was hardcoded to zero for
Volteer, but the S0i3.4 substate was not disabled. According to my
conversations with Intel engineers, that was not enough to guarantee
detection pulses shorter than 100us. But it is entirely possible that
we have just been "lucky" that the SoC has not gone into low power
mode during the boot process, where most of the cr50 communication
happens.)
TEST=util/abuild/abuild -t GOOGLE_VOLTEER -c max -x
BUG=b:154333137
Change-Id: Idef1fffd410a345678da4b3c8aea46ac74a01470
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add DTT (Dynamic Tuning Technology) support for Jasper Lake based rvp board.
Set power limits and CPU sensor thresholds for DTT based thermal control.
BRANCH=None
BUG=Noe
TEST=Build and boot on jslrvp board
Change-Id: I41409c70d8472c54ca452fc98d5ee9edf3ccd307
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Support 4GB Samsung K4UBE3D4AA-MGCR discrete DDR bootup.
BUG=b:162379736
BRANCH=kukui
TEST=emerge-jacuzzi coreboot
Change-Id: I2f4f084ece067e9884c23004506b450a281a77a6
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45101
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the dooly variant of the puff reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.2).
BUG=b:155261464
BRANCH=puff
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_DOOLY
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Change-Id: I8e714cc9bf4a49266da77db88f8c4a3ca45878d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
3.6 schematic will separate TS power from eDP PP3300 to GPIO
for power control and correct GPIO assignment from GPIO_90 to
GPIO_32 instead.
BUG=b:161579679
BRANCH=zork
TEST=emerge-zork coreboot
Change-Id: Ieef67e1d04201c5d9e1dc625c519e6d0307c55f0
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Ie663d424edbbeeb8f5691b00f3977f7501e9ab45
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45110
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Change-Id: Idd38ab530fd8a0c16231f3499eac393c333a9a92
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Change-Id: I8db3bfbdb557a84413408b4b39a13b24c45497cc
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Change-Id: I3371bed7c2678fbc3304f53af1413a93462933f5
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45108
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Enable SataPortsDevSlp for SATA ports 2 and 3.
Change-Id: Id6c69f4a6fe45cb5c6aad3f42c741a2724c6166c
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Change-Id: Idf64d98b36ca95a8bc17a6544993c26e23851cd8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45107
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Change-Id: Ic5587402700d7b137e20538549b8a09a64cb6a9f
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Enable the I2C HID driver, configure I2C bus 0 and add the touchpad
device to the devicetree.
Tested on lemp9, touchpad confirmed to use i2c-hid driver in Linux
instead of PS/2.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Ic3a90fda134b1d53f28ab687b3033ec52fee843b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43623
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop duplicated code for spd.bin generation that is provided globally
in lib/Makefile.inc.
For all affected boards it has been verified that the output binary
functionally matches the original one. The changed execution order of
Make instructions influenced the cbfs file order. Hence, the rom images
can't be compared directly.
Thus, the output files of the two timeless abuild runs have been compared.
Further, it was verified that the final files in cbfs stay identical, by
comparing the extracted cbfs of each board.
The boards (possibly) needing modification could be found with something
like this (with false positives, though):
find src/mainboard -name Makefile.inc | \
xargs egrep 'SPD_BIN|SPD_DEPS' | cut -d: -f1 | sort -u
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Icd3ac0fd6c901228554115c6350d88bb49874587
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
_GPE cannot be anywhere but at the root of the ACPI namespace.
This change ensures that is always the case.
Tested on lemp9, GPE still in correct location.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Ib31683b06e61da4b1859cd939c36879cebf4c03c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43630
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GPIOs required for DeepSx (e.g. SLP_SUS#) are not hooked up on the
lemp9. Therefore, drop the DeepSx settings.
Tested on lemp9, suspend works correctly.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Iab179abd7adc3a65dcfc43ce1b5742d514b711fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43629
Reviewed-by: Michael Niewöhner
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested on lemp9, SA thermal device appears in lspci.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I527e586b1dae5f8087d2364c63c9db5bcb643214
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner
|
|
Setting USBx_PORT_EMPTY is not a requirement anymore, since unset
devicetree settings default to 0 and the OC pin now only gets set when
the USB port is enabled (see CB:45112).
Thus, drop the setting from all devicetrees.
Change-Id: I899349c49fa7de1c1acdca24994ebe65c01d80c6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Don't configure USB3 port 4 since it's not used.
Change-Id: I6919f5ec3a5be53373f2ab75063764287b53baf5
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45105
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Michael Niewöhner
|
|
CPU_INTEL_HASWELL is already selected at nb/intel/haswell/Kconfig.
Change-Id: I608286aae72bc740be642a72109472fb235f37bf
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Currently HECI3 gets enabled by the option Heci3Enabled, but this
duplicates the devicetree on/off options. Therefore depend on the
devicetree for enablement of the HECI3 controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Heci3Enabled setting, and divergent
devicetrees were adjusted.
Change-Id: Ic7d52096aee225c2ced1e1bc29ca850fe5073edc
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44579
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on the Lindar's schematic, generate memory settings.
util: rename lp4x spds to include "lp4x-" in name
BUG=b:161089195
TEST=FW_NAME=lindar emerge-volteer coreboot chromeos-bootimage
Signed-off-by: Rasheed Hsueh <rasheed.hsueh@lcfc.corp-partner.google.com>
Change-Id: I1ec35d62f8ed21356329b78a614114edad78c2bc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Michael Niewöhner
|
|
Since there are 4 different versions of FSPs for the Comet Lake
platform, add a new Kconfig option for the currently used SoC being able
to differ between the various SoCs and FSPs.
The new Kconfig option selects the Comet Lake SoC as base for taking
over its specific configuration and is only used for configuring the
path to its specific FSP header files and FSP binary.
Also, adjust all related mainboards so that their Kconfig selects the
new option.
For details, please see
https://github.com/intel/FSP/tree/master/CometLakeFspBinPkg
Built System76/lemp9 with BUILD_TIMELESS=1 before and after this patch
and both images are equal.
Change-Id: I44b717bb942fbcd359c7a06ef1a0ef4306697f64
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
GPP_F14 should be configured to be routed via APIC and not SCI.
BUG=b:162528549
TEST=verified on a volteer
Change-Id: Ie262ceeaea1c07bcc99e1545f5eb99e0d0dee905
Signed-off-by: Alex Levin <levinale@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44948
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Dual DDR4 Samsung K4AAG165WA-BCTD 16Gb x 8
BUG=b:165956925
BRANCH=zork
TEST=1. gen part id by gen_part_id
2. emerge-zork coreboot
Change-Id: Ia21a561e9b89feeccb6509d9280eaf52cfc2f5a3
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Some Trogdor variants power their USB hub from a PMIC LDO that is
already enabled by QcLib, and some have a discrete LDO that is
controlled by GPIO_84. For the latter, let's make sure we assert that
GPIO on boot.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I9d206cd7154ded3bf179e68c2b1421d0a8ee89f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: mturney mturney <mturney@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
|
|
We're moving a lot of pins around on Trogdor again. For firmware this
only affects the RAM and SKU strapping ID pins. Since there are quite a
few of the old devices in circulation this time and some people seem to
care about mosys RAM information working, let's actually check the board
revision and support both cases this time.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If7728d8ea4b7f6e7ff6721ade90f975f6efd5ddd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
1. Update paramerters form thermal team.
2. Update PL2 Max/Min to 51W/15W.
BUG=b:167494420
BRANCH=puff
TEST=build noibat and verified by thermal team.
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: Id96e681e9a990a1a1eaeb22781b1c60a7369118b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45020
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Set tcc offset to 5 degree celsius
2. Apply the DPTF parameters receive from the thermal team.
3. Change PL2 min value from 25W to 15W.
BUG=b:167477885
BRANCH=puff
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I68fdefe99cf36a39797c29ad84d08321bb8175f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
DRIVERS_INTEL_WIFI is already set to yes.
Change-Id: I09f628a9c1feb8992b6fe7c7ca93c75243ffc0f1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
This reverts commit 2ad859988b5243411393fdf3116eea281b92b1bb.
Reason for revert: broke the build
Change-Id: I7e7d917c2e8b698d5c7c3ce0b6d34e80696185f3
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44993
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on the Lindar's schematic, generate memory settings.
BUG=b:161089195
TEST=FW_NAME=lindar emerge-volteer coreboot chromeos-bootimage
Signed-off-by: rasheed.hsueh <rasheed.hsueh@lcfc.corp-partner.google.com>
Change-Id: I75fb9254ec7aa40acc2e125f0c4fd31003d28be6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
1. Add new SPD file, "samsung_dimm_K4E8E324ED-EGCG.spd.hex".
2. Add SPD support in Rammus memory table, as follows:
SPD_SOURCES += samsung_dimm_K4E8E324ED-EGCG # 0b0110
SPD_SOURCES += samsung_dimm_K4E6E304ED-EGCG # 0b0111
BUG=b:166576463
BRANCH=firmware-rammus-11275.B
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure system boots up.
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I82386507c4e996e0a59c26ce50de3bced45b1196
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44854
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TPM2 set to yes by MAINBOARD_HAS_TPM2 at security/tpm/Kconfig file.
Change-Id: I815d545618e2e734f8e9b65731bbb4bed0b2d93d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
BOOTBLOCK_CONSOLE is already set to yes in console/Kconfig file.
Change-Id: I2a4ee517795bc7b378afc5eae92e2799ad36111b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
GENERATE_SMBIOS_TABLES is already set to yes at src/Kconfig
Change-Id: I2845f4f329283360a49ea40dfee7d9a232ab4ea1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Modify the BOARD_SDRAM_TABLE_OFFSET as 0x10
BUG=b:162891673
BRANCH=kukui
TEST=make
Change-Id: I5a4794d6e899e35686c40a553b991643f9e35ea3
Signed-off-by: xuxinxiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jianbo Zhang <zhangjianbo@huaqin.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
|
|
'CONSOLE_SERIAL' is already set to 'y' at src/console/Kconfig.
Change-Id: I350cf12a115c6ebe54a2b0821edc94c29db8d137
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
1. Apply the DPTF parameters receive from the thermal team.
2. Change PL2 min value from 25W to 15W.
3. Change PL2 max value from 64W to 51W.
BUG=b:166696500
BRANCH=puff
TEST=build and verify by thermal team
Change-Id: I53a4e8809369883c3ba77744fdc05fb510408209
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44903
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Convert 0X -> 0x
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Iea3ca67908135d0e85083a05bad2ea176ca34095
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch converts the current DPTF policies from static ASL files into
the new SSDT-based DPTF implementation. All settings are intended to be
copied exactly.
BUG=b:158986928
BRANCH=puff
TEST=duffy boots and dumped SSDT table for quick check.
Change-Id: I45987f44ec381917173f8d2a878edb50da454b4b
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Relative path to spd directory was wrong.
BUG=b:167175547
TEST=Boot Trembyle SKU 2
Change-Id: I63ae4f39ba69d2d80c25ac7383b6eb953901f56d
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44946
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO_144 is REPORT_EN pin for the touchscreen controller where 1 means
enable operation and 0 means stop operation. Override tree exposes
this pin as stop GPIO. Thus, it needs to be configured as active low
i.e. 0 = active (stop), 1 = inactive (enable report).
Change-Id: I349123655260349b78d2f75f846da0ce1dc966fc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
v3.6+ of reference schematics have moved to using active low polarity
for touchscreen GPIO. This change sets the default polarity in
override tree accordingly to active low. To support boards from older
builds, variant_touchscreen_update() already updates the polarity to
active high.
BUG=b:161937506
Change-Id: I370bdb27ea5d0601612d13b515113a6048018964
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
These changes are according to spd_binary_optimization_volteer_v0.4 sheet.
Offset Current value Updated value Analysis
1 0x10 0x11 As per SPD spec rev 1.1
5 0x19 0x21 16 bits for Row addrs, 10 bits for Column addrs
6 0x95 0xB5 4 die, 2 ch per pkg, Byte 16 signal matrix
12 0x02 0x0A 2 ranks per ch, 16 bits device data width
18 0x05 0x04 4267MHz support
29 0x90 0xC0 HW specific
30 0x06 0x68 HW specific
31 0xD0 0x60 HW specific
32 0x02 0x04 HW specific
125 0x00 0xE1 4267MHz support
BUG=b:159319534
TEST=Tested multiple cold boot cycles on TGL-UP3 with QS silicon
Change-Id: Ie506fbfe86a3ffb77763e8d9ef7e8aa69ea44bd3
Signed-off-by: Shreesh Chhabbi <shreesh.chhabbi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42524
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:155002684
TEST=emerge-dedede coreboot chromeos-bootimage
Change-Id: I87d8575131e745dec818bc5864ca6b21ce0825af
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Checked with the schematics that all PCIe clocks have a corresponding
clock enable pin.
BUG=b:149970243
BRANCH=zork
Change-Id: If96cdf95e213682217e46a98fc69c5c2ef4a148d
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44892
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:149970243
BRANCH=zork
Change-Id: I0b31466c5a991b02cef3432942f8de45805fe546
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44891
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:149970243
BRANCH=zork
Change-Id: Ie3fc83484c6ce769956dc8e6e57194ffebb4f5b0
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44890
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
dirinboz does not support stylus, config AGPIO4/5 to NC
to prevent unexpected wake event for s3.
BUG=none
BRANCH=zork
TEST=emerge-zork coreboot chromeos-bootimage
Change-Id: I3cfdeb326c3d3775148b2a00732c7d848dab35cb
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44894
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
berknip does not support stylus, config AGPIO4/5 to NC
to prevent unexpected wake event for s3.
BUG=b:162376046
BRANCH=zork
TEST=emerge-zork coreboot
Change-Id: I8d9b711ce1d7300181fe496d490dd33b38bc5983
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44893
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some Linux kernel drivers bind to "DMI quirks." In this case, the audio
fw_config is added as an OEM string, e.g., "AUDIO-MAX98357_ALC5682I_I2S"
so the audio topology can be correctly discovered.
But add all successfully probed fw_config items as well, because this
makes it easier to view what is selected from userspace.
BUG=b:161963281
TEST=With CBI FW_CONFIG field set to 0x201:
localhost ~ # dmidecode -t 11
# dmidecode 3.2
Getting SMBIOS data from sysfs.
SMBIOS 3.0 present.
Handle 0x0009, DMI type 11, 5 bytes
OEM Strings
String 1: DB_USB-USB4_GEN2
String 2: AUDIO-MAX98373_ALC5682I_I2S
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I7b7586b0ebfe7b2fd888f448a50ae086364fa718
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I21378acd6408a4fae5600a54a41f695e54221dc2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44829
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ibc2446d7b8d4334e26ca6335179f50b7abe301cb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44831
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPP_F11 was in the early gpio table, but the definition was missing
from the main gpio_table. This change adds GPP_F11 to the gpio_table
array.
BUG=none
TEST="emerge-volteer coreboot" and verify it builds correctly.
Change-Id: I40f887300a9dfd4f8e790031b77bbee8a014f499
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
Add Makefile.inc to include six generic DDR4 SPDs for the following
parts for Eldrid:
DRAM Part Name DRAM ID to assign
H5AN8G6NDJR-XNC 0 (0000)
MT40A512M16TB-062E:J 1 (0001)
H5ANAG6NCMR-XNC 2 (0010)
K4A8G165WC-BCWE 0 (0000)
K4AAG165WA-BCWE 3 (0011)
MT40A1G16KD-062E:E 3 (0011)
Add mem_list_variant.txt as a manifest of eldrid's DRAM parts for use
by gen_spd, the generic DD4 SPD generation tool.
Add dram_id_generated.txt to specify DRAM ID strap settings.
NOTE that Eldrid specified DRAM IDs for the first three parts to be 0
though 2 (i.e. no combined DRAM IDs for parts that use the same SPD).
BUG=b:161772961
TEST="FW_NAME=eldrid emerge-volteer coreboot" and verify it builds
without error.
Change-Id: Ica62e299ed40e60c2d5928b29ead5d2205b1af66
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44272
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4c7f23615bcfd9c2bda2cac8808544b98f8e25a2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ib82689150689716bc9afdf8d4527a1dcd5deae56
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Enable TBT2 setting in overridetree.cb based on schematic.
BUG=b:165175296, b:166060548
BRANCH=none
TEST=Check all USB ports USB2 and USB3 both functional
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I23ecf76a3c2f631211b0ae2898707c68862b374b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44747
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Set tcc offset to 5 degree celsius for kaisa and duffy
BUG=b:166696500
BRANCH=puff
TEST=Build, and verify test result by thermal team.
Change-Id: I2bb977b98c0764f0b9cac3543074da56057717cf
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44901
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
MODEM_CLKREQ / CNVI_CLKREQ has no external pull-down resistor.
When there is no M.2 card populated, the pin is floating. Thus
enable an internal 20K PD.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I37e0a9d7e9e0a8c8a7ac198abfd3995b8b0f9e3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Add CNVi and PCIe wifi devices to the devicetree and enable the wifi
driver and SMBIOS tables in Kconfig.
Test: both CNVi and PCIe wifi devices work fine
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I16e04dbbf5fc3a163ce5a2bb8de646877d5cbc0f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43654
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rework the comments:
- fix wrong gpio / net names
- convert all comments to <gpio> / <net name>
- add more information where appropriate
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I51b552fd3255d5627dcc012e677bad51be517cf0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43650
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Convert PAD_CFG_TERM_GPO with pull "NONE" to its shorter equivalent
PAD_CFG_GPO.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I9ed4d97ba184fa3e72425d5d16042a142b0640b4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43649
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
INTP_OUT can be used as Type-C VBUS sense input/interrupt but is
currently unused in coreboot. It isn't a requirement for PD to work.
Disable it for now.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I233fbb562969487dff095ba6589fb9da3301ae4a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43647
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable internal pull-ups for SATAXPCIE pads since there are external
ones at the M.2 slot's PEDET pins.
Test: both, SATA and NVME devices work fine on both slots
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I6be716620695ac38c44a17abe1c4de97b099b8d7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43645
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are pads being unused for various reasons:
a) missing board support (DeepSx: SUSWARN#)
b) unneeded feature ID pins
- currently no known device models without keyboard backlight
- currently no known device models without TPM
c) BOARD_ID (L140CU/L140ZU) is fixed and known at build time
d) DDR_TYPE_*: there is only one known ram model
e) strap-only pads
f) unconnected pads
Configure them as NC with appropriate pull-up if no external pull exists.
The latter was checked by schematics and looking at the board.
When any of the unused ID pins is needed in the future, they can be
reactivated easily (configure as GPI).
Further, convert from use of legacy macro PAD_CFG_NC to PAD_NC.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ia370c180d5ae6f48360be14af3cbab29e6814e75
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43644
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To support CSE Lite firmware update, CSE RW partition is extracted from
CSE blob binary and added to FW_MAIN_A and FW_MAIN_B.
CSE RW size for TGL is close to 2.3MB; hence, the size of FW_MAIN_A and
FW_MAIN_B is increased to avoid an overflow.
BUG=b:140448618
TEST=build with me_rw binary blob for volteer and boot to kernel.
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Change-Id: Ie3c2b657f0426d206dfe3729829ec34ff57812c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43790
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
L140CU has a TPM2 connected via SPI. Add the TPM device to the
devicetree and enable it.
According to Intel doc#615170-001, PIRQ is required for SPI TPM to work.
Since the TPM is connected to GPP_A7, enable NF1 (PIRQA#) and set it as
TPM interrupt in Kconfig.
Note: The PCH maps either LPC TPM or SPI TPM to the same address and
handles either LPC or SPI communication transparently. Thus we can use
MAINBOARD_HAS_LPC_TPM here, which implements TPM via that address.
Tested, but only polling works currently, because there is some upstream
issue with the tpm_tis module in current Linux kernels. [1]
[1] https://bugzilla.redhat.com/show_bug.cgi?id=1770021
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I26d3b396fe1e99368e18fd3a6a9f02e3585b9f6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43641
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
burnet/esche
Add LPDDR4x DRAM index#0 Samsung K4UBE3D4AA-MGCR 4GB
BUG=b:165956924
BRANCH=kukui
TEST=emerge-jacuzzi coreboot
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I644b65d77b79891ed65215d810b970fe43b29e3f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44821
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modify USI_RESET_L GPIO_140 in touchscreen power on/off sequence
to be active low.
BUG=b:160126287
BRANCH=Zork
TEST=emerge-zork coreboot
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I53dd872fdacb95cda43f297d2c3f9c6723b27bad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44858
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SATA is currently turned on in the Dalboz and Trembyle base board
variant devicetrees, even though no Google/Zork device uses SATA; for
mass storage they either use eMMC or NVME PCIe SSDs. This patch disables
both the SATA PCIe device and the bus where it was the only enabled
device on. The next patch in this patch train sets a new FSP-M UPD
setting
BUG=b:162302027
Change-Id: Ie7773d9dcb0518c3e01bdd0af23b62268ab64694
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44068
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested on OCP Delta Lake, with FSP WW34 DCI can be connected if enabled.
Change-Id: I8e0dff921cef02dfc66467a2b8fa3e196fb36ac2
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|