| Age | Commit message (Collapse) | Author |
|---|
|
Set up EMMC gpios for payloads.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: I1e7ee9bfe3a26ed04374e8c74243f48552a1d254
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/28546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
As we don't use the MIPI camera on Rammus, disable SA Imaging Unit and
CIO2 devices to avoid the system failed to enter S0ix.
BUG=b:114502527
BRANCH=master
TEST=On DUT, echo freeze > /sys/power/state
1. check the S0ix status on EC console
2. check the value of /sys/kernel/debug/pmc_core/slp_s0_residency_usec
Change-Id: I91629732db01ee534f0ddb67a2b358d725ef810e
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/28543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We have a pin from AP to EC, called AP_IN_SLEEP_L (SRCLKENA0 on AP side,
pad R23) that is supposed to be high in S0, and low in S3 (and X/don't
care in S5).
This should be set as early as possible in bootblock.
BUG=b:113367227
TEST=make; boots and verified AP_IN_SLEEP_L GPIO is high.
BRANCH=None
Change-Id: Icd59fa366c162e7443b8932a851e65f110f551ab
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/28585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@google.com>
|
|
Turn on SOC_INTEL_CANNONLAKE_MEMCFG_INT for coffeelake rvp platform
for easier collabration on newer platform. The setting in memory.c get
from board design itself.
BUG=N/A
TEST=Build and boot up with whiskey lake rvp platform.
Change-Id: I10f3af4bed511153cef4d6f3a93caea57cc4ae90
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28257
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch sets the MRC UPD CmdTriStateDis for the atlas boards.
Atlas is a LPDDR3 design without RTT for CMD/CTRL.
The original change for
nocturne is I0f593761dcbd121e7e758421af178931b9d78295
mb/google/poppy: Set UPD CmdTriStateDis for Nocturne
BUG=b:111812662
Change-Id: I45b6dd22412c689c8db64f4650e9fa9e87dec2ec
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
At ECC 2017 user Bob reports, that an image built for the Lenovo T500
runs on the Lenovo W500 without any issues.
Change-Id: I17fd9725ab85ba2f0c99a70f40e35432265a81c1
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/22226
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Felix Singer <migy@darmstadt.ccc.de>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3eacba9c1c20bbfa270dd7a9afabe48ed9092bcc
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/28622
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ram_resource is board specific and should be moved there.
Change-Id: I50bd9aaaae39422e565d8bf205a6365c59299df0
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/28621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
IOMMU was tested on Xen 4.8 and Linux kernel 4.14.33. Following feature
set is enabled:
(XEN) AMD-Vi: Disabled HAP memory map sharing with IOMMU
(XEN) AMD-Vi: IOMMU Extended Features:
(XEN) - Peripheral Page Service Request
(XEN) - Guest Translation
(XEN) - Invalidate All Command
(XEN) - Guest APIC supported
(XEN) - Performance Counters
(XEN) AMD-Vi: IOMMU 0 Enabled.
Change-Id: I6dbfae78849248f3532caa78974c8f2ce61a530d
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-on: https://review.coreboot.org/26116
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9f7e7d70b850619e34a60fd8e7b16b44c728e9ca
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Based on SiFive bootloader code
Change-Id: I71043ce9e458e25e64da28d53cd36b02d2e22acc
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/28604
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Invoke clock_init in romstage for SiFive Unleashed.
Change-Id: Ib869762d557e8fdf4c83a53698102df116d80389
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/28602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The board version is part of EC's EEPROM, but is not being populated
from EEPROM. Instead a default Kconfig parameter is returned as board
version. Select GOOGLE_SMBIOS_MAINBOARD_VERSION Kconfig item to enable
requesting the EC for board version.
BUG=b:114001972,b:114677884,b:114677887
Change-Id: Ib404a9da35156e197d232088fd7ca69432effbca
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Tested-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/28539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This modification for DVT build and use CBI method
enable all memory particles.
BUG=b:112870780
TEST=verify it under the EVT unit and pre-test EVT
unit(rework RAM ID follow the proposal) respectively.
Change-Id: I488a0652ba348eff9a6d8591b0cfa6ed4fe808aa
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28579
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I637792d3bf22d2e452144d44ba03cfe45b47501d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28580
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
HAVE_INTEL_FIRMWARE is used to enable certain options that rely on a valid
Inter Flash Descriptor to exist. It does *not* identify platforms or boards
that are capable of running in descriptor mode if it's valid.
Refine the help text to make this clear.
Introduce a new option INTEL_DESCRIPTOR_MODE_CAPABLE that does simply
declare that IFD is supported by the platform. Select this value everywhere
instead of the HAVE_INTEL_FIRMWARE and default HAVE_INTEL_FIRMWARE to
y if INTEL_DESCRIPTOR_MODE_CAPABLE is selected.
Move the QEMU Q35 special case (deselection of HAVE_INTEL_FIRMWARE) to
the mainboard directory.
Change-Id: I4791fce03982bf0443bf0b8e26d9f4f06c6f2060
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/28371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Only for those that are x86 and also have a RW_LEGACY region.
The assumption is that all devices touched have 64k block sizes when
choosing size and alignment of the region.
Change-Id: I12addb137604f003d1296f34f555dae219330b18
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add MICRO 4G and 8G SPD file.
BUG=none
BRANCH=master
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure system boots up.
Change-Id: I7cb5b7f2bcdc6fbe0cbc640cad4af014f1a0edd6
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28484
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
add two memory parts and ram id:
hynix_dimm_H5ANAG6NCMR-VKC
micron_dimm_MT40A1G16KNR-075E
BUG=b:113983573
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: Ia052f16b6c1e64ee6458fbdeea56a482a728c35a
Signed-off-by: Ren Kuo <Ren.Kuo@quantatw.com>
Reviewed-on: https://review.coreboot.org/28536
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On rammus, headset uses DA7219 so that we need to enable it.
BUG=b:112945714
BRANCH=master
TEST=emerge-rammus coreboot chromeos-bootimage
Flash FW and check in kernel to see if DA7219 is up.
Change-Id: I92dd412374d007aab264661e698fbbbbcf1eae45
Signed-off-by: marxwang <marx.wang@intel.com>
Reviewed-on: https://review.coreboot.org/28537
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch sets the MRC UPD CmdTriStateDis for the
nocturne boards.Nocturne is LPDDR3 design without RTT
for CMD/CTRL.
BUG=b:111812662
TEST=Run memtester app and also webgl fishtank on
the LPDDR3 kabylake boards and also check the
margin data is proper in FSP.
Change-Id: I0f593761dcbd121e7e758421af178931b9d78295
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/28379
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
VPD reference: https://chromium.googlesource.com/chromiumos/platform/vpd/+/master/README.md
Copy ChromeOS VPD driver to add support for VPD without CROMEOS.
Possible use case:
* Storing calibration data
* Storing MAC address
* Storing serial
* Storing boot options
+ Now it's possible to define the VPD space by choosing
one of the following enums: VPD_ANY, VPD_RW, VPD_RO.
+ CHROMEOS selects now VPD as part of it.
+ VPD is implemented as driver.
Change-Id: Id9263bd39bf25d024e93daa57053fefcb1adc53a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25046
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
AMD chips don't hold off a reset to the end of I2C transitions, so
devices on the i2c bus can be left in a bad state. To avoid this,
make sure the trackpad and touchscreen chips get disabled
during boot.
BUG=b:114411165
TEST=build, reboot watch trackpad enable go low
Change-Id: Ie50f4a102249df79517da571a6e768dba804cd57
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28538
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds support for a x2 NVMe device on PCIe bus PCIe lines 5+6 and
clock#4.
BUG=b:113369699
TEST=booted on atlas
Change-Id: I08e7c4d65662ddbb7d936915c896eb1fcb240ba8
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Id7e8ad63de2a6094c66cbd47ae9b7707a9af4e81
Signed-off-by: Mikolaj Walczak <mwalczak@fb.com>
Reviewed-on: https://review.coreboot.org/28529
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
this enables spi console for wedge100s with broadwell_de. the console
size is 64kb. enabling spi console in `board.fmd` enables code which
calls into `timer_monotonic_get` (from `spi_flash_cmd_poll_bit`) and
`udelay` (from `ich_status_poll`). this patch selects `TSC_CONSTANT_RATE`
in fsp_broadwell_de's Kconfig to satisfy that.
Change-Id: Ib925c5aee88b65c46a81534405c364dd5649f8e8
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-on: https://review.coreboot.org/28528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
This change configures GPIO_63 (which is used for H1 interrupts) as Rx
Level. This ensures that the signal gets passed on to the next logic
state as is and the APIC entry can be configured to trigger interrupt
on level or edge as per the kernel driver expectation.
TEST=Verified that no H1 interrupt timeouts are seen with 100
iterations of warm and 100 iterations of cold reboot.
Change-Id: I7aac30300a4251d9b40276dcca7ebc6a6d814c40
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
this enables mrc cache in fmap for wedge100s and always enable it in
Kconfig.
Change-Id: I27cd236f67a6500b40fc3eb731397d408402f041
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-on: https://review.coreboot.org/28527
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On rammus, system halt was observed because of gspi clk value being set to 0.
Log info from serial coreboot:
FMAP: area RW_NVRAM found @ 9fa000 (24576 bytes)
SF: Detected FAST_SPI Hardware Sequencer with sector size 0x1000, total 0x1000000
VBNV: Restore from flash failed
ASSERTION ERROR: file 'src/soc/intel/common/block/gspi/gspi.c', line 443
gspi.c
442
443 assert(gspi_clk_mhz != 0);
444 assert(ref_clk_mhz != 0);
445 return (DIV_ROUND_UP(ref_clk_mhz, gspi_clk_mhz) - 1) & SSCR0_SCR_MASK;
BUG=none
BRANCH=master
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure system boots up.
Change-Id: Ibe3937902901b2cdc1a196415c08fabb0f3155f2
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28405
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DMIC's are now connected to DMIC_CLK0/DMIC_DATA0.
So, enable the pins accordingly.
BUG=b:113744731,b:111106010
BRANCH=none
TEST='emerge-nocturne coreboot chromeos-bootimage' builds the image
Change-Id: I48cace3c6099a2853fcb377c695a5e325094baf6
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/28433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Nautilus-Wifi with m3 AP got a halt issue during CTS test.
Nautilus-Wifi was FCS with Celeron AP first and also its PCB/BOM was
validated only with Celeron. Since Celeron deos not support turbo
boost mode, its steady power demend and lower CPU frequency may not
reflect the potential noise hidden inside the board.
Bumping VCC_SA voltage offset 75mV confirmed works to mitigate the
potential noise coupling to VCC_GT/SA, and we verified this change
makes this issue go away on Nautilus-Wifi board.
Nautilus-LTE doesn't show this issue, since it has 10L PCB, will have
better grounding and less noise/ripple than 8L PCB.
BUG=b:111417632
BRANCH=poppy
TEST=Verified CTS test pass without an issue.
Change-Id: Id13fcc36a5b6ed42620c66f57a7303f30bff1a50
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/28439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change enables tablet mode ACPI device for all octopus boards.
BUG=b:113348027
Change-Id: I69a5dd41cd0958b93f8eed338fed4b6ee77a178f
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28466
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Set GPIO135 high to enable audio through the BCLK buffer.
BUG=b:113559558
TEST=None
BRANCH=grunt
Change-Id: I1dcecf5960d3c91e0c2165e7f8856ff423c06e8c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28482
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use ICH10's file instead of ICH7's.
Change-Id: I02678179e8f1dbd9b9f7d6407383a7a6cad15011
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/28450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add CMOS option that allows to use both integrated and discrete GPU.
Tested on ThinkPad W530.
Change-Id: I8842fef0fa1235eb91abf6b7e655ed4d8598adc7
Signed-off-by: Evgeny Zinoviev <me@ch1p.com>
Reviewed-on: https://review.coreboot.org/28393
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the mainboard.c in order to support the sku id in smbios
table where the sku id is queried from the eeprom via EC.
BUG=b:113714761
BRANCH=master
TEST=check the result of 'dmidecode'
Change-Id: I3413784cca1ac10a2468d84f2d06c0e1d701fdcb
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/28426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable dGPU power handling on Lenovo ThinkPad T430, T530 via PMH7
register 0x50.
Although there's no Thinker-1 chip on these models according to
schematics, dGPU power control via PMH7 works the same as on T420/T520,
so they can be considered Thinker-1-compatible.
It can be tested from linux userspace using util/pmh7tool.
To turn dGPU power off:
pmh7tool -c 0x50 7
pmh7tool -c 0x50 3
To turn it on:
pmh7tool -s 0x50 3
pmh7tool -s 0x50 7
To check whether it is on (bash):
reg=0x$(pmh7tool -r 0x50)
echo "$(( (( reg & 0x08 )) >> 3 ))"
or just `pmh7tool -b 0x50 3` with
https://review.coreboot.org/#/c/coreboot/+/28388/
Tested on ThinkPad W530.
Change-Id: Ieab1a33b3c680c757cc0999660b5cb7e122474cc
Signed-off-by: Evgeny Zinoviev <me@ch1p.com>
Reviewed-on: https://review.coreboot.org/28392
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the DRIVERS_SPI_ACPI to enable the tpm device node.
Without DRIVERS_SPI_ACPI, the kernel will popped out the below error:
cr50-update[592]: Starting cr50 update
cr50_get_name[595]: updater is /usr/sbin/gsctool -s
cr50-update[609]: exit status: 3
cr50-update[613]: output: Could not open TPM: No such file or directory
cr50_get_name[615]: board_id: '' board_flags: '0x', extension: 'prod'
cr50-update[617]: hashing /opt/google/cr50/firmware/cr50.bin.prod
cr50-update[678]: current state 3 in /var/cache/cr50.a3055efbc9.state
cr50-update[682]: not running
cr50-result[782]: Not running normal image. Skip setting Board ID
trunksd[795]: TPM: Error opening tpm0 file descriptor at /dev/tpm0: No such file or directory
BUG=none
BRANCH=master
TEST=/dev/tpm0 is created
Change-Id: I35287c6c54299c2677c41fc830675570b9d45a94
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/28400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable Synaptics touchpad device for liara
BUG=b:113309346
BRANCH=master
TEST=Verify touchpad on liara works with this change
Change-Id: Icdafe34a00fd55d5338fa07ffa304e48e7b85e7b
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch overhauls the Cheza FMAP, removing some sections we don't
seem to need (RW_CDT, the two RW_XBL_BUFFERs, and the second copy of
RW_DDR_TRAINING), and adding new sections we're going to need soon or
should have had anyway (RO_DDR_TRAINING, RO_FSG, RW_LEGACY).
Make more use of implicit offsets and sizes, because we can and because
it should make future adjustments easier.
Change-Id: I0bd9e59e9cfa162c478c4bd1f048fcac61ad5062
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/28403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: T Michael Turney <mturney@codeaurora.org>
|
|
After adjustment on Liara Proto
Audio: 399.2 KHz
H1: 398.3 KHz
TP: 399.0 KHz
BUG=b:113319200
BRANCH=master
TEST=emerge-grunt coreboot chromeos-bootimage
measure by scope
Change-Id: Ibba8c823ed8451a804cf731d49e7568a94ac7c6b
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Because of an incorrect transmit voltage swing, the signal must be
adjusted. The factor of slices for full swing level can be corrected via
the High Speed I/O Transmit Control Register 3.
Change-Id: I116802cd2a944658fc3022e948eba43cebe52bb4
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Alex Thiessen <alex.thiessen.de+coreboot@gmail.com>
|
|
Set threshold parameter for grip sensor STH9321
.ProxCtrl6: 75
.ProxCtrl7: 99
BUG=b:113303916
BRANCH=poppy
TEST=Built and verified parameter passed to driver
Change-Id: I8a410a23b5e3831fc8e90118b810fc2409a026eb
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/28381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Enrico Granata <egranata@chromium.org>
|
|
Also removed internal pull ups for CX_PREQ_L and
CX_PREQ_L signals as they have external pull ups.
BUG=b:110654510
TEST=On Yorp Proto 2, flashed image and verified that it boots to OS.
Checked Wake-on-Wifi works with both cnvi and pcie modules.
Also executed a few suspend resume cycles.
Change-Id: I0a76cd2a1481c828fc092aaf7e870a411624879c
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/28328
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Grunt takes a few seconds to update the EC, so display a notification
screen while that's happening.
BUG=b:113286040
TEST=Boot Grunt with old EC firmware, see update screen
Change-Id: I95fc4d3430bac66c09f57a4d34abde08752e5f0e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add weida touchscreen support
BUG=none
BRANCH=master
TEST=emerge-octopus coreboot, and verified that touchscreen works on
meep.
Change-Id: I4352322820237e4c2289410af6643e15109060a1
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Modify the previously SOC_CNL_LPDDR4_INIT to SOC_CNL_MEMCFG_INIT, to
make the infrasturture to handle both LPDDR4 and DDR4 cases in the
future. Consider the case of reading SPD from SMBus other than providing
SPD pointer directly.
BUG=N/A
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully.
Change-Id: I2f898147f67dd52b89cc3d9fc4e6b3854fa81f57
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28248
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set EC SPI bus config and init SPI bus according to the config.
BUG=b:80501386
BRANCH=none
TEST=EC is not working yet. This makes depthcharge go forward a little.
Change-Id: Id9209b6429417430cfcf7f5a5a1659e7e4bc7866
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/28251
Reviewed-by: Joel Kitching <kitching@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set up EC interrupt GPIO to boot depthcharge. Without this patch,
depthcharge will fail to detect EC interrupt GPIO.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui and see in logs, that depthcharge detects
EC interrupt GPIO.
Change-Id: I0ec2c70c189a059219954e0384aaf98995285728
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/28250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The firmware of devices connected to LPC should deassert the LPC CLKRUN#
signal when there is no bus activity on LPC.
Necessary changes:
- Enable LPC CLKRUN#
- Enable LPC PCE (Power Control Enable)
- Enable LPC CCE (Clock Control Enable)
- Remove I/O decoding range on LPC for COM 3
- Disable I/O UART driver
Change-Id: I2fd80e3fdcf23658f97b8182a77df7e09ddf25d6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Bayhub eMMC controller default runs SD base 50MHz at the first power on.
After boot into OS, mmc kernel driver will config controller to HS200/208MHz
and send MMC CMD21 (tuning block).
But Bayhub PCR register 0x3E4[22] (eMMC MODE select) is not clear
after system warm reset.
So eMMC will still run 208Mhz but there is no block tuning cmd in depthcharge.
It will cause two Sandisk eMMC (SDINBDA4-64G-V/SDINBDA4-32G-V) to fail to
load kernel and trap in 0x5B error (No bootable kernel found on disk).
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: Ic080682e67323577c7f0ba4ed08f8adafca620cc
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Reduce the CPU passive threshold sample rate from 5 seconds to 1
second so DPTF will react faster to rapid temperature increases.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BUG=b:113101335
BRANCH=atlas
TEST=manual performance/power testing on nocturne.
No longer see messages like below in syslog,
'CPU0: Package temperature above threshold'
Change-Id: I2dc9d157b54500bae29e123978bb8ad6e05ef619
Reviewed-on: https://review.coreboot.org/28325
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Reduce the CPU passive threshold sample rate from 5 seconds to 1
second so DPTF will react faster to rapid temperature increases.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BUG=b:67459049
BRANCH=nocturne
TEST=manual performance/power testing on nocturne.
No longer see messages like below in syslog,
'CPU3: Package temperature above threshold'
Change-Id: Ic20c718fd3a496db7c7192feec4f230d924cc458
Reviewed-on: https://review.coreboot.org/28324
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update TSR1 trip point from 48C to 50C.
Also, change power limit2 minimum value from 8W to 10W.
These are the values as per recent thermal tuning.
BUG=b:79779737
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: I33a9d2dc3e0e5566d95b1f1e46d3922dc8965b2b
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/28187
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit fixes the values and thus fixes the issue of
audio device not getting detected on random reboots.
Change-Id: I34a4f62815d192005c3324d4f71b0aba377fe738
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/28280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
|
|
Change-Id: Ie3ee4acfd272991133f02a56df6e23aa6071d3e9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Some unneeded includes are also removed.
Change-Id: Icd518c46d8503d11d24466c30840d7e514e9a05d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Most FADT report using ACPIv3 FADT table. Using the get revision
function keeps the table versions in sync.
Change-Id: Ie554faf1be65c7034dd0836f0029cdc79eae1aed
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28277
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch disables the unused PCI clock outputs on the XIO2001 PCI
Express to PCI Bridge.
Change-Id: I0b9cf51a713f4ab46e71d250397486d136c26177
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28284
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
add device "WCOM Digitizer" and "Synaptics Touchpad" for bobba
BUG=none
BRANCH=master
TEST=emerge-octopus coreboot
Change-Id: Ie0bf8ebab6d9cb9c8fe42a500efaa3d11ae359db
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28332
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
TEST: same sha256sum with BUILD_TIMELESS=1.
Change-Id: Icf3368bcf1351f0e7cd4041c3792d76362aec9e5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
To increase the lifetime of the circuit, it is necessary to reduce the
eMMC speed to DDR50 mode.
Change-Id: I40658b44a99e6600ed00950a1a177961f0055e7a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This enables CBAS device on Nocturne to allow hid-google-whisker driver
in kernel properly detect device configuration.
Change-Id: I5905a2de208e94062f2768a9b7d22147f85c7f38
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-on: https://review.coreboot.org/28262
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For the 1st redesign of mc_apl1 mainboard some adjustments are
necessary:
- The FPGA is now connected directly via a PCIe Root Port
- Internal Apollo Lake UARTs are now used
- Adjusting GPIO settings
Change-Id: I8917a52325306f24d1c39a88dac47b0cee760d57
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
A FPGA is not necessarily available in further mc_apl1 variants. So we
move the loading of the driver and the notify function to the mc_apl1
variant.
Setting the CPU to Max Non-Turbo Ratio is also not absolutely necessary
for further variants.
Change-Id: I9f8438407f231df08e1ad04655bb6f747257e268
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This supports the Foxconn d41s, d42s, d51s, d52s.
The following is tested (SeaBIOS 1.12 + Linux 4.9) and works:
- COM1
- S3 resume (with SeaBIOS needs sercon disabled)
- Native graphic init on VGA output
- SATA
- USB
- Ethernet
- PS2 keyboard
The base for this mainboard port was the Intel D510MO port.
Change-Id: Ie4ec9cbf70adcdddbc2e5d805e4806825c320072
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28227
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
src/mainboard/google/octopus/mainboard.c
Function dev_find_slot may return NULL,
check before its usage.
Found-by: klockwork
BRANCH=None
TEST=Built & booted Yorp board.
Change-Id: I160adbe3b0a5a2b0f11fd1567513860664d4bee3
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28235
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The change updates GPIO configuration for meep.
1. Update touchscreen power enable GPIO in devicetree.
2. Provide default override tables for GPIO configuration.
BUG=b:112955087
TEST=Boot on meep proto board with Intel (Jefferson Peak) wifi card.
Change-Id: Idb4e7a510eef15c2e118058d5848080782f4f665
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/28252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Since ifdfake has been deprecated in favor of better alternatives, such
as flashrom IFD parsing. Therefore, there is no need to support ifdfake
any further. Remove the IFD_*_REGION values on the few motherboards with
them.
Change-Id: Ie07116a7fb960c6ca832d802016f22c6677baac9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28232
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates the board id check for version >=2 to apply new
GPIO configs.
BUG=b:112618194
Change-Id: I3544c9596c465615818d2040682e554a64fc6b1a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28263
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This should not be board specific.
Change-Id: Ifa617e84af767f33a94f1ddfa7d4883c1a45198f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change PL1 from 4.5W to 7W, based on thermal test results.
BRANCH=eve
BUG=b:73133864
TEST=Verify the MSR PL1 limitation is set to 7W.
Change-Id: Ic3629f9c3b7eb6eef1a1b5a3051c9a11448bc9ad
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28078
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds support for controlling the keyboard backlight over ACPI.
BUG=b:112619894
BRANCH=none
TEST=verified keyboard backlight can be adjusted using keyboard
shortcuts
Change-Id: I25713f341e8b5a4e50903ac109bfa717f20969d8
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28205
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Enhanced Intel SpeedStep (EIST) on nocturne.
Change-Id: Ie9b832f5bc3a5ef300783bd9bcd7cf5d186b98fa
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable Enhanced Intel SpeedStep (EIST) on eve.
Change-Id: I49b18b817cda570f5c3c4d048c4e03329ac10b87
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch moves uart functions which are common across multiple soc to
block/uart. This will remove redundant code copy from soc
{skylake/apollolake/cannonlake}.
BUG=b:78109109
BRANCH=none
TEST=Build and boot on KBL/APL/CNL platform.
Change-Id: I109d0e5c942e499cb763bde47cb7d53dfbf5cef6
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This is meant to solve an issue where the proximity sensor may fluctuate
between CLOSE / FAR in rapid succession upon the user removing their hand
from the unit, before settling on the correct output.
Using the hardware debouncing filter solves this issue and removes the
spurious fluctuations.
BRANCH=None
BUG=None
TEST=manual on Nocturne, observing events come in
Change-Id: I78cc4852d42fcda6209fedce1ce91236b5814571
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/28112
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Weida touchscreen controller needs 130 ms delay after reset
BUG=b:111102092
BRANCH=master
TEST=Verify touchscreen on fleex works with this change
Change-Id: Ia86c3acf3c0e09ca05cc1681113672b546f830a0
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I4b0577bf3c00307733a1096749c1835d86764f29
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ib5799cceacefa89385a7615ef1c4b4d06157044f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Fix scope of ResourceSource, which should match the scope of the
device itself.
Change-Id: I9d0ff0ecc2721ec55b1ed12dddb495cd55966daf
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/28114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
All different memory configuration should be supported by now.
Thanks to Igor Lee.
Change-Id: Ib93c0e3cbdc29cbf6cff26292df4fbbb8208082f
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Igor Lee <getrun@gmail.com>
Reviewed-on: https://review.coreboot.org/27781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The romstage main() entry point on arm64 boards is usually in mainboard
code, but there are a handful of lines that are always needed in there
and not really mainboard specific (or chipset specific). We keep arguing
every once in a while that this isn't ideal, so rather than arguing any
longer let's just fix it. This patch moves the main() function into arch
code with callbacks that the platform can hook into. (This approach can
probably be expanded onto other architectures, so when that happens this
file should move into src/lib.)
Tested on Cheza and Kevin. I think the approach is straight-forward
enough that we can take this without testing every board. (Note that in
a few cases, this delays some platform-specific calls until after
console_init() and exception_init()... since these functions don't
really take that long, especially if there is no serial console
configured, I don't expect this to cause any issues.)
Change-Id: I7503acafebabed00dfeedb00b1354a26c536f0fe
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/28199
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After adjustment on Careena EVT
TP: 400.0 KHz
TS: 396.8 KHz
H1: 396.8 KHz
BUG=b:112663934,b:112664258
BRANCH=master
TEST=emerge-grunt coreboot
measure by scope
Change-Id: I9eeaf9290d95969a283f14618878e28faf0ea46f
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28119
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix the following failure from FWTS:
FAILED [LOW] AMLAsmASL_MSG_SERIALIZED_REQUIRED: Test 1, Assembler remark in line
131
Line | AML source
--------------------------------------------------------------------------------
00128| }
00129| }
00130| })
00131| Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
| ^
| Remark 2120: Control Method should be made Serialized (due to creation of named objects within)
00132| {
00133| Name (RBUF, ResourceTemplate ()
00134| {
================================================================================
ADVICE: (for Remark #2120, ASL_MSG_SERIALIZED_REQUIRED): A named object is
created inside a non-serialized method - this method should be serialized. It is
possible that one thread enters the method and blocks and then a second thread
also executes the method, ending up in two attempts to create the object and
causing a failure.
BUG=b:112476331
TEST= Run FWTS.
Change-Id: I6f4f6e7e94b01f673afc97d9415481ee63e406e3
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28122
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update SPD details to match with Coffeelake U RVP board
BUG=none
BRANCH=none
TEST=Boot on coffelake U rvp board and check if memory training is
passing and board boots till payload.
Change-Id: I953354cf5c6045731262f4f4e9da230187c2d246
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Update GPIO table as per board schematics.
GPIO table for other variants will be added later.
Change-Id: Ieb55d160ae2d6bff940840b1fba9411979332d4d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Nami doesn't support wakeup from hibernation by CR50. This causes the
device to remain turned off after CR50 update.
This patch disables turning off EC on cr50 update. CR50 resets the
whole system. So, EC reset is not required.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
BUG=b:112604277
BRANCH=none
TEST=gsctool -a -u /media/removable/cr50.bin && reboot
Verify EC reboots. AP prints 'Waiting for CR50 reset to pick up update'
then reboots.
Change-Id: I06f5eb6100e8af6ffec45d4de2b40eff44f89709
Reviewed-on: https://review.coreboot.org/28113
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These files are being updated to match the prevailing style
of cmos.default files.
Change-Id: I47d31d6fec8c9eb856aed0c63824d9556b7705e4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
change I2C irq to EDGE trigger
BUG=b:112616824
BRANCH=master
TEST=emerge-grunt coreboot
Raydium TS is working.
Change-Id: I86ec32bb3f2626e65d76c3259e3c4244a970e5de
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Used default console log level is 7 in src/console/Kconfig.
So let cmos.default use the same level as default.
Change-Id: Ia39ee457a8985142f6e7a674532995b11cb52198
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Side effect was observed that after override BayHub EMMC
driving strength to the max, EMMC CLK will be reduced to
51.x Mhz from 200 Mhz.
This will cause OS installation fail on Samsung EMMC sku.
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I848ab0cae474b15fbc4264c8ade63d5c6b4e489d
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This file contains two instances of "dptf_enable" = "1". This change
removes the 2nd instance (it doesn't have an explicit comment like the
1st instance).
The dptf devices still seem to be present even with this change, as
expected.
Change-Id: I890006644be9176ebaf555cc121c816e12f2b596
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The spec of the sx9310 says the I2C interface can handle standard
(100kb/s) and fast mode (400kb/s). The current setting is using fast
plus (1000kb/s) so this change is reducing the speed to fast mode.
I've been using the sensors with this change for a few weeks now, though
I also don't recall seeing an issue prior to this change.
Change-Id: I337fc02c52565d6ec4d7bac1b3564f65238962dc
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28075
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit 1fdb76945a9d06bbff37dee9da69e13a86c933f4.
Camera power is now handled by ACPI rules - no need to force the GPIOs
on by default.
BUG=b:80106316,b:111141128
Change-Id: Ifefec320884989f106a4b09c956d3a3279a1491a
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28072
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Ping-chung Chen <ping-chung.chen@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This defines new GPIO pin for controlling the display panel CABC
function. The default value is high (enabled).
BUG=b:112154569
Change-Id: I29083ab18e37f929a55b450b143463c67fe0abea
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28070
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This updates the DPTF sensor names to reflect the sensor locations on
the board.
BUG=b:75454415
TEST=verified new strings show up in
/sys/devices/LNXSYSTM:00/LNXSYBUS:00/INT3400:00/*/description
Change-Id: Ibffe6cb361de212ca03e75deaa8c454546d267a5
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28069
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ia38c6f8d978065090564d449cae11d54ddb96421
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch updates Power Limit (PL) for AML.
- PL1 as 5W TDP as POR
- PL2 as 18W TDP as POR
BUG=None
BRANCH=None
TEST=Build coreboot for Nocturne board and check default PL1/PL2 TDP.
cat /sys/class/powercap/intel-rapl/intel-rapl\:0/constraint_0_power
5000000 (5W TDP)
cat /sys/class/powercap/intel-rapl/intel-rapl\:0/constraint_1_power
18000000 (18W TDP)
Change-Id: Icb02a8a7c5fcd5e6aee45f14eba540a6b3ed3d67
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/27427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add TSR2 DART/DTRT package
BUG=b:110451144
BRANCH=nami
TEST=emerge-nami coreboot chromeos-bootimage
Test image with dptf.dv
Change-Id: I3328e17328415f5ebdcf84263e5456e11e55f769
Signed-off-by: T.H. Lin <t.h_lin@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
