| Age | Commit message (Collapse) | Author |
|---|
|
Braswell boards don't work well with the eMMC and SD controller
in ACPI in payloads other than depthcharge - SeaBIOS requires
an onerous workaround (manually determining the PCI BAR0 address
for each eMMC and SD controller, then adding adding etc/sdcard
entries to the CBFS), and Tianocore can't see the devices at all.
To make the common use-case work better, switch to PCI mode.
Test: build/boot cyan variants with SeaBIOS and Tianocore
payloads, verify eMMC and SD card visible and bootable to
both payloads and OSes.
Change-Id: I71947603e22a37fe2c8ef4eaac8a3aa0d0ed1cec
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40002
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Simply cyan variants by converting to overridetree format.
A few differences were ignored as there appears to be no
reason behind them:
- cyan had PCIe RP2 enabled, but nothing is attached to it
- kefka had the SPI 1 device disabled
- reks, relm, and ultima had HSUART 1 disabled
- edgar had I2C1 UPD disabled
Test: build/boot cyan and edgar variants, verify everything
still works
Change-Id: I9928cc59adcfda4661ddfdfa95f53a7820053b4a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39964
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Simplify glados variants by converting to overridetree format.
Change-Id: I6dd7a4b1ae7f1d3ce9fadb06ea95e021a1c880a5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39983
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The VR config values used in the variants' devicetrees is
identical to the domain defaults in vr_config.c, with the
exception of the icc_max value, which is calculated dynamically
based on SKU, and again matches the default values for
each domain and each varaint.
Test: add a print function to dump the VR config values for each
domain from the UPDs after setting, verify same output before/after.
Change-Id: I4307f6e19ae6f99d4f5e475b181fd66c5b92f28c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39982
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In preparation for conversion to overridetree format, clean up
the variant devicetrees in order to minimize the differences
across glados variants. This entails:
- minor reformatting and reordering of devicetree entries
- addition of setting default values on boards which skipped them
- disabling unused I2C2 on boards which left it enabled
- ensuring TCC offset set for all SKL-Y boards
- setting VR mailbox command 1 for caroline
- skipping init for UART2 on cave and glados
- dropping unused PCIe RP5 for sentry
Change-Id: I628b20a69fab187e67901c9eb98c0e2ddcb76b0d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39981
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the variants' devicetrees are almost identical, convert to
using an overridetree setup for simplicity.
As part of the cleanup, drop unused PCIe RP5 for buddy as well.
Test: build all auron variants, compare generated static.c to ensure
resulting generated contents unchanged (although layout will)
Change-Id: I290e7243335a64afdcfc629db7b8ce18f5aa993c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
beltino variants are Chromeboxes without built-in displays,
so now that default_brightness_levels.asl is no longer required
for all boards in a platform, drop it.
Change-Id: Ie8147763fc9fdf4f184d3d000bffd6794e134d9e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ie7eb4c43178acff2dc5ff7c685e71990d8f353c9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
No longer needed anywhere.
Change-Id: Ifeea76af44377d917ec46cac0d9d7375d1a68204
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39961
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
NDID/DID entries are no longer used by the GMA SSDT generator, so
drop them. SSDT generation will be simplified in a subsequent commit.
Remove direct setting of gnvs->ndid in qemu-q35 board since build
will otherwise break.
Change-Id: Ifbf08f43291c1fff7ccbc85272dc97334207983b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39954
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These two identifiers were always very confusing. We're not filling and
injecting generators. We are filling SSDTs and injecting into the DSDT.
So drop the `_generator` suffix. Hopefully, this also makes ACPI look a
little less scary.
Change-Id: I6f0e79632c9c855f38fe24c0186388a25990c44d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39977
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: David Guckian
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change reorganizes memory initialization code for LPDDR4x on
TGL to allow sharing of code when adding support for other memory
types. In follow-up changes, support for DDR4 will be added.
1. It adds configuration for memory topology which is currently only
MEMORY_DOWN, however DDR4 requires more topologies to be
supported.
2. spd_info structure is organized to allow mixed topologies as well.
3. DQ/DQS maps are organized to reflect hardware configuration.
TEST=Verified that volteer still boots and memory initialization is
successful.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib625f2ab30a6e1362a310d9abb3f2051f85c3013
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
This commit creates a malefor variant for Volteer. The initial settings
override the baseboard was copied from variant ripto. Fine tune GPIO
and memory DQ based on malefor schematics.
BUG=b:150653745
BRANCH=volteer
TEST=emerge-volteer coreboot
Signed-off-by: William Wei <wenxu.wei@bitland.corp-partner.google.com>
Change-Id: Idbeebb13e537287686344740211143df35b7863a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39857
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds GOOGLE_LAZOR which is just a copy of GOOGLE_TROGDOR for
now.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I0dca8e1c29bdd91625d58b3cb583b530ed925e9f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bob Moragues <moragues@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
|
|
This implementation removes all JSL references from the TGL SoC code.
Additionally, mainboard code changes are done to support build.
BUG=b:150217037
TEST=build tglrvp and volteer
Change-Id: I18853aba8b1e6ff7d37c03e8dae2521719c7c727
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Switch to using Jasper Lake SoC code from soc/intel/jasperlake and stop
referring from soc/intel/tigerlake.
Addtionally mainboard changes are done to support build.
BUG=b:150217037
TEST=Build and boot waddledoo. Build jasperlake_rvp and volteer board.
Change-Id: I39f117bd66cb610a305bcdb8ea65332fd0ff4814
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Certain PCIe endpoints cause an exception inside AmdInitMid when PCIe
ClockPM is enabled in AGESA PCIe initialization structures. Disable it
to allow platform to boot with such devices. coreboot driver enables
the ClockPM correctly on such devices anyway.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I7fb13f915861c26cf773960abb12a3a1c0211cdc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Including gma.asl at the platform level (vs the board level)
means that even desktop boards need to include the default
brightness levels, which makes no sense. To begin to clean this up,
include gma.asl in default_brightness_levels.asl (as well as
the handful of board-specific brightness files) and remove it
from the various platforms.
A follow-on commit will remove default_brightness_levels.asl
from all boards which lack an internal display.
Change-Id: I8063deeef4ab6d6ab34ed9b0be5b1d541d6e9b6b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39878
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allow Chrome OS to be enabled for this QEMU target. By default
this does not change anything unless it is selected in the build
configuration, but it makes it possible.
Native VGA init is not forced when Chrome OS is enabled because the
drm-bochs driver does not work with chrome (even the latest upstream
kernel driver with drm atomic support) but it does work with virtio.
The coreboot graphics init needs to match what is selected with qemu
(with -vga std or -vga virtio) which in turn will determine which
kernel driver is used.
A second FMAP is added with both RW-A and RW-B regions which is
required by chromeos.
Recovery mode can be entered by supplying a custom fw_cfg option
when launching qemu: -fw_cfg name=opt/cros/recovery,string=1
Change-Id: I24b4532ea961e68558663292c99d121f0a30ce3b
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This enables the mainboard to use a TPM if it is selected in the
configuration. By default this does nothing, but it allows the
TPM to be enabled and used with the CONFIG_USER_TPM2 Kconfig option.
Using a TPM with QEMU requires either a physical TPM backend or
the swtpm package with a socket:
-chardev socket,id=swtpm,path=/tmp/swtpm/socket
-tpmdev emulator,id=tpm0,chardev=swtpm
-device tpm-tis,tpmdev=tpm0
Change-Id: I0d79a5a0f590c57998ababb660b52d9e3ed2d484
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
QEMU does not have a separate northbridge chip, so the mainboard
needs to handle the ACPI name and paths so that devices can get
generated into the SSDT properly. This fixes the PIRQ and TPM
table generation.
This issue can be seen in the coreboot output:
ACPI_PIRQ_GEN: Missing LPCB ACPI path
Change-Id: Ifc7d4359eea38ac0b55d655e39191ae7f8655fe4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Ensure that the low memory is properly reserved so it does not get
marked as normal RAM and get wiped or reused by firmware or the kernel.
This ensures that the low RSDP is always available for the kernel.
This is only noticed if something wipes the RSDP before the kernel
boots, which happens if you use the depthcharge payload and boot in
developer mode.
Change-Id: I7295018416229bc957ecbf26f77623a57965557e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
When the TPM is enabled in QEMU the fw_cfg interface will return
~200KiB of ACPI tables, so this needs to be increased from the default
in order to be able to boot.
This is seen when using a TPM with qemu as it will hang when
processing the fw_cfg tables.
qemu-system-x86_64 \
-machine q35 -enable-kvm -vga virtio -serial stdio \
-drive 'id=hd,file=disk.bin' -bios coreboot.rom \
-chardev 'socket,id=swtpm,path=/tmp/swtpm/swtpm-sock' \
-tpmdev 'emulator,id=tpm0,chardev=swtpm' \
-device 'tpm-tis,tpmdev=tpm0'
Change-Id: I21980aace8e86e636f5ae7b55148f4c31404edba
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Was accidentially removed in 6e50849
Change-Id: I090b6bc8863d17412cb1e23ac816c39f479290c1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39937
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the variants' devicetrees are almost identical, convert to
using an overridetree setup for simplicity.
Test: build all slippy variants, compare generated static.c to ensure
resulting generated contents unchanged (although layout will)
Change-Id: If237fad38a1bccfb8e51edfae3ecb75d05ade240
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Clean up Link's mainboard dir by putting the SPD files in
a spd subdirectory like all other/newer boards use, and
selecting GENERIC_SPD_BIN to include them in the build.
Test: build google/link and verify spd.bin unchanged
Change-Id: I9c2f9f77dbdd6552c5ae1e7a0df2051b9b85badc
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Link's DID data makes no sense, and ACPI backlight controls don't work
as a result. Replace them with the default profile used by most/all
other boards.
Test: build/boot google/link, verify ACPI backlight controls functional
Change-Id: Ia7cb3f10bd3c05ebaf414c17a8f94d2e9b40ae26
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Currently, those who want to use measured boot implemented within
vboot should enable verified boot first, along with sections such
as GBB and RW slots defined with manually written fmd files, even
if they do not actually want to verify anything.
As discussed in CB:34977, measured boot should be decoupled from
verified boot and make them two fully independent options. Crypto
routines necessary for measurement could be reused, and TPM and CRTM
init should be done somewhere other than vboot_logic_executed() if
verified boot is not enabled.
In this revision, only TCPA log is initialized during bootblock.
Before TPM gets set up, digests are not measured into tpm immediately,
but cached in TCPA log, and measured into determined PCRs right after
TPM is up.
This change allows those who do not want to use the verified boot
scheme implemented by vboot as well as its requirement of a more
complex partition scheme designed for chromeos to make use of the
measured boot functionality implemented within vboot library to
measure the boot process.
TODO: Measure MRC Cache somewhere, as MRC Cache has never resided in
CBFS any more, so it cannot be covered by tspi_measure_cbfs_hook().
Change-Id: I1fb376b4a8b98baffaee4d574937797bba1f8aee
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Add an enable reset delay to avoid messages like this in the
kernel:
i2c_hid i2c-WCOM50C1:00: failed to change power setting.
This gets rid of all the warnings except one on reboot/shutdown.
That last case likely isn't fixed because the sleep command is
being sent directly from i2c_hid_shutdown(), so no ACPI routines
get to run and provide the delay. Since the machine is going down
for shutdown/reboot anyway, fixing that last case is a lower
priority.
BUG=b:145094539
TEST=Run on kohaku, switch to guest mode and log out, no errors
Signed-off-by: Evan Green <evgreen@chromium.org>
Change-Id: I8fadf497dd09e5b95b1d74443fb0543d3555dbb8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39707
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
It is not a single mainboard anymore, it's actually three variants.
Change-Id: I66f1239abadd8bf93269d6d4617329dc4b925e8d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Make use of overridetrees, as these mainboards are very similar.
Tested on GA-H61MA-D3V, still works fine.
Change-Id: I1b587a091da631cb172eb76722958da6c7518893
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39668
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3dfa303b6aae2446fa3a1d67a6e31448277cacdb
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
TEST=build with BUILD_TIMELESS=1, binary does not change
Change-Id: I56983cabfad574b970aba098a178e691c6b354d1
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Get ready to squash all the ASUS i440BX boards together.
Change-Id: Ibc9bfa4fc5b582bf658215bda298523e8ee7b36b
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Coalescing is not needed, as root port #1 is enabled. Also, update the
comments to look more like the other two variants. Note that the Intel
H61 PCH only has six root ports, so devices 1c.6 and 1c.7 do not exist.
Change-Id: I3f4bf99ceec6c77f6e1eabea9b712245afee7d34
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39742
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This initial devicetree attempts to correctly configure the status of
each PCI device. Not all required drivers are instantiated, nor are
all of the SoC options fully selected yet.
PCIe root ports are enabled and clocks are assigned.
USB ports are assigned.
BUG=b:150165131
BRANCH=none
TEST=util/abuild/abuild -p none -t google/deltaur -x -a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I911ec08b0db3647d131113a138fb74a55612fd62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
This configuration sets up all of the GPIO pads for the first rev of
the board.
BUG=b:150165131
BRANCH=none
TEST=util/abuild/abuild -p none -t google/deltaur -x -a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4f6398808809492dcb345ccaa09e199fa35e40cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Created a new Google baseboard using Tiger Lake named deltaur, taking
volteer as a starting point.
BUG=b:151102807
TEST=make build successful
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Ib98f328df22f39e7d9d625a3292954881ee15b15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
In order to create a working baseline all ports are being set to have
retimers. Setting the TcssAuxOri UPD to 0 in order for the SoC to not
misconfigure the ports. Volteer will need some additional changes after
this is implemented to account for ports that do not have a retimer.
This setting is in the process of being documented in the TGL EDS and we
can update once it is fully understood what this setting is changing on
the SOC side.
BUG=b:145943811
BRANCH=none
TEST=Boot to OS and check Type-C port1 Display on Volteer,
Connecting Type-c display should work regardless of Type-c cable
orientation.
Change-Id: I29eb0513299126ad8d1ee11ded2c771f28ad13f3
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39460
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the halvor variant of the volteer reference board by copying the
template files to a new directory named for the variant.
BUG=b:151399850
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_HALVOR
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: If4d3417ba55d56af441c99d949a196328d7a1951
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Update the GPE configuration for dw0, dw1 and dw2.
BUG=None
TEST=build and boot tglrvp
Change-Id: I8b406bcbd710e84cec91a8c2d1557902e929f7cc
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39844
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable wifi sar feature and set wifi sar name for kled sku.
BUG=b:152277272
TEST=emerge-hatch coreboot chromeos-bootimage and
verify wifi SAR load by sku-id
Change-Id: I9ee242773fd05cc2bcd7bde07da8176022827677
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Glados boards do not have an exposed serial port outside
of the servo interface. Set board Kconfig so that a default
built image with Tianocore payload is bootable and doesn't
hang due to trying to send data over a non-existant serial port.
Test: build/boot google/chell with board defaults
Change-Id: Ifad6f805e66438e2c436d9fa235d9be2ecf69179
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use it wherever the standard numbers were copied to. Bit 31 is set
at runtime unconditionally, so we don't need it here.
Change-Id: I0d853c3b8250a2c7b2d1a91985a555e4b17ad76c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39731
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Further backport the backlight-PWM handling from Skylake. Beside
configuring the PWM frequency in Hz, we also use the PCH's logic
for the brightness setting via BLM_PCH_OVERRIDE_ENABLE. Linux
would toggle it anyway and that might confuse our ASL code.
We assume that the 183Hz value that was set before for Slippy
variants was overridden by Linux with the 200Hz VBT value, like
it was for the Broadwell Chromebooks. So we set 200Hz for them
in the devicetrees. The calculated value for the T440p of 220Hz
seems sane and also matches the VBT.
Change-Id: I17dfe1a3610d5e2918c617cf5d10896692fdccb3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Cyan has no VGA BIOS available (at least not publicly), so
remove related options. Disable SoC serial output by default,
since no production devices have this exposed, but leave it
as a user option so it can be selected as needed (eg,
for use with a Google debug servo).
Change-Id: Ic079a39ca5ad0ac653b52248244b94d4bfbd08a4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39872
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Chrome-EC/PD images for all glados variants need to be built
from the board-specific branch, not master. Including the default
board names serves no purpose and requires users to deselect
the "use built-in EC firmware" in order for the board to build.
Test: build google/chell with defaults
Change-Id: Ic10f11337b85035068cdc4fe8147413e6b7f57ac
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add missing port definition for the mSATA/WWAN mPCIe port,
set OC pin for internal ports to OC_SKIP, fix port
descrption for mPCIe/WLAN port, remove USB3 definition for
right type-A port as it is USB2 only.
Test: insert WiFi module into WWAN port, observe BT portion
detected and functional.
Change-Id: Ie39b99eeb0f605ff07d57c32189fb1f4183713e4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Create the sushi variant of the hatch reference
board by copying the template files to a new directory named
for the variant.
(Auto-Generated by create_coreboot_variant.sh version 3.0.0).
BUG=None
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_SUSHI
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: Ie900d09ff55e695527eafe68a5a75cd4a0b6d340
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Just a minimal set of board files needed to get it to boot
in 1 CPU mode.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: Ie2f944964e938d8026a6d5d8a22a8449199d08aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Tioga Pass comes with AST2500 BMC which offers SuperIO functionality.
However we currently do not configure/enable SuperIO chip. As a result
system boots pretty silently on cold boot. Then FSP configures SuperIO
and resets the system so on next boot serial console does work. This
makes debugging difficult because pre-FSP output is invisible.
This patch enables bootblock to properly configure desired BMC SuperIO
port so early serial output is visible.
TEST=do a cold boot on OCP Tioga Pass, observe bootblock output starting
from bootblock.
Change-Id: Iff8e6a862858d733f529bb9b8c65e22e5ec6b521
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
|
|
Change-Id: Iad0b394dea017223a5b92fff0cb4c2ed1d5a7bd7
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39402
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1.Select CHROMEOS_EC related Kconfig for variant board with
external EC support.
2.Select proper CHROMEOS Kconfigs which are required for all
variants.
3.Disable Intel EC region in case of external EC.
BUG=None
BRANCH=None
TEST=Compilation is successful for both Jasper Lake RVP variants.
Change-Id: I290b3748777e18476651101de71df9080dd3105c
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39584
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The board version is part of EC's EEPROM, select Kconfig item to enable
requesting the EC for board version.
BUG=b:152374066
TEST=Verified the mainboard version is from EC's EEPROM.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Idd8aceed83439cb500e2b03153e9f8ba93979ee8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Change-Id: Icda241cfac7b428176515d7996a48cb01b1dc976
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39815
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7304b06d7bf34fb7126acfdef811481dc5cba598
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update the icc_max for the GT-Sliced VR domain according to the
hardware design.
BUG=N/A
TEST=build
Change-Id: Ib9f7d77d144a282214e6bda8a4e836873c395487
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39804
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The format for VPD has changed s.t. the first NIC should
always have a zero concat to the end.
Adjust all the respective boards to shift back by one and
adjust drivers/net friends to remove the 'special casing'
of idx == 0.
Background:
https://chromeos.google.com/partner/dlm/docs/factory/vpd.html#field-ethernet_macn
V.2: Fixup a code comment typo while we are here.
V.3: Vary special casing semantics for idx==0 => default mac addr is set.
V.4: Rework to still support the legacy path.
BUG=b:152157720
BRANCH=none
TEST=none
Change-Id: Idf83cc621a9333186dabb668b22c4b78e211930a
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Refactor the code and split it into Xeon common and CPU-specific code.
Move most Skylake-SP code into skx/ and keep common code in the current
folder.
This is a preparation for future work that will enable next
generation server CPU.
TEST=Tested on OCP Tioga Pass. There does not seem to be degradation
of stability as far as I could tell.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I448e6cfd6a85efb83d132ad26565557fe55a265a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39601
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sometimes coreboot needs to compile external code (e.g.
vboot_reference) using its own set of system header files.
When these headers don't line up with C Standard Library,
it causes problems.
Create stdio.h and stdarg.h header files. Relocate snprintf
into stdio.h and vsnprintf into stdarg.h from string.h.
Chain include these header files from string.h, since coreboot
doesn't care so much about the legacy POSIX location of these
functions.
Also move va_* definitions from vtxprintf.h into stdarg.h where
they belong (in POSIX). Just use our own definitions regardless
of GCC or LLVM.
Add string.h header to a few C files which should have had it
in the first place.
BUG=b:124141368
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I7223cb96e745e11c82d4012c6671a51ced3297c2
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39468
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Define a chip option to explicitly soft reset all enabled GPIOs to
default state.
TEST=boot FreeBSD 11.2 on PC Engines apu1, change GPIO configuration
using nctgpio module and check whether GPIOs are reset after reboot
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Iae4205574800138402cbc95f4948167265a80d15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The 2nd COM port's base address defaults to 0x2f8. Current software
for this system expects the port at 0x3e8.
Configure COMB to use 0x3e8 instead of 0x2f8.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: Ibb462bad5f0594e0b5c8dea6e02cd42d58d999ab
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Remove unused SMM_STORE space and use it for RW_LEGACY area
BUG=None
TEST=None
Change-Id: I5724b860271025e8cb8b320ecbd33352ef779660
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
The concerned GPIO is configured as an open drain at the Embedded
Controller side without an external pull-up. This causes leakage in the
PP3300_A rail. So configure the GPIO to have a weak internal pull-up at
the SoC side.
BUG=b:151680590
TEST=Build the mainboard. Ensure that there are no leakages in the
PP3300_A rail.
Change-Id: I5553cf40adb92edc0fecab5c875ec8d72063ba7b
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We should only define function to get lid switch and recovery mode
switches when CHROMEEC_SWITCHES is not available. Correct this to avoid
compilation issues
BUG=None
BRANCH=None
TEST=jslrvp code compilation is fine
Change-Id: I2445d40da1540c9d8c8c5fc845a4f38a5abf983e
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39585
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add memory initialization parameters for Jasper Lake RVP boards
Jasper Lake RVP supports two variants, one with memory LPDDR4
and another with DDR4
Based on board id, mainboard will pass correct memory parameters
to the fsp.
BUG=None
BRANCH=None
TEST=Check compilation for Jasper Lake RVP and check memory training passes.
Change-Id: Idc92363a2148990df16c2068c7986013d015f604
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39195
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The ACPI Spec 2.0 states, that Processor declarations should be made
within the ACPI namespace \_SB and not \_PR anymore. \_PR is deprecated
and is removed here.
Additionally add processor scope patching for P-State SSDT created by
AGESA, becasue AGESA creates the tables with processors in \_PR scope.
TEST=boot Debian Linux on PC Engines apu2, check dmesg that there are
no errors, decompile ACPI tables with acpica to check whether the
processor scope is correct and if IASL does not complain on wrong
checksum, run FWTS
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I35f112e9f9f15f06ddb83b4192f082f9e51a969c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39698
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A bigger than zero value of bmc_boot_timeout must be set
for KCS ipmi_get_bmc_self_test_result() to run, otherwise
the self test result will be error and won't write SMBIOS
type 38 table. Here we set 60 seconds as the maximal self
test timeout.
Tested=Check if the BMC IPMI response data and SMBIOS type
38 on OCP Tioga Pass are correct or not.
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Change-Id: I3678973736a675ed22b5bc9da20a2ca947220f4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Nuvoton NCT5104d has no LDN 0xe according to its datasheet.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I0d34218d88b779b08c380d2396ff9ab9253597fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Enable ASPM L0s and L1, Common Clock and Clock Power Management for
all PCIe ports.
TEST=boot Debian linux and check new PCIe capabilities appear in lspci
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I0a4c83731742f31ab8ef1d326e800dfdc2abb1b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
PC Engines apu2 had many problems with PCIe cards detection. The cards
were inconsistently detected when booted from G3, S5 or after a reboot.
AGESA can reset PCIe slots using GPIO via callback. Use it to reset the
slots that support using GPIO as reset signal.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I8ff7db6ff85cce45b84729be905e6c895a24f6f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The `link_frequency_270_mhz` setting was originally used by the native
graphics init code for Sandy/Ivy Bridge, which is long gone.
The value of this information (which board had it set) is questionable.
The only board that had an LVDS panel and set it to 0 was the ThinkPad
L520, where native graphics init was never reported to work. Also, the
native graphics init only used it for calculations, but never confi-
gured the hardware to use a specific frequency. A look into the docu-
mentation also doesn't reveal any straps that could be used to confi-
gure it.
Change-Id: Ieceaa13e4529096a8ba9036479fd84969faebd14
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39763
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
_DCS, _DGS and _DSS are required by specification. However,
we never implemented them properly, and no OS driver com-
plained yet. So we stub them out and keep the traditional
behavior in case an OS driver checks for their existence.
The old implementations also only returned static values as
there never was any write to their GNVS variables. The TRAP()
that was called in one place is actually implemented by some
ThinkPad's SMI handler as docking event. However, as the call
precedes these SMI handlers in coreboot history, it's most
likely an accident.
Change-Id: Ib0b9fcdd58df254d3b2290900e3bc206a7abd92d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
The format for VPD has changed s.t. the first NIC should
always have a zero concat to the end. drivers/net supports
this with the workaround of setting the idx to 1.
The longer term fix is to adjust all the respective boards
to shift back by one and adjust drivers/net friends to
remove the 'special casing' of idx == 0.
Background:
https://chromeos.google.com/partner/dlm/docs/factory/vpd.html#field-ethernet_macn
BUG=b:152157720
BRANCH=none
TEST=none
Change-Id: I510428c555b92398a5199b346dffb85d38495d74
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39768
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I385339761b3e1b5dcadb67b8ca29b1518c2db408
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The ACPI Spec 2.0 states, that Processor declarations should be made
within the ACPI namespace \_SB and not \_PR anymore. \_PR is deprecated
and is removed here for Intel CPUs only.
Tested on:
* X11SSH (Kabylake)
* CFL Platform
* Asus P8Z77-V LX2 and Windows 10
FWTS does not return FAIL anymore on ACPI tests
Tested-by: Angel Pons <th3fanbus@gmail.com>
Change-Id: Ib101ed718f90f9056d2ecbc31b13b749ed1fc438
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
A certain somebody (that would be me) forgot how to count, it seems.
Change-Id: Iac0ac5827ca242c465a2e8be92a823c8fc9b2935
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39741
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Coalescing is not needed, as all PCIe ports are used.
Change-Id: Icf31f6672e0a54d119a6537da1b52c42f9cee823
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39740
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
IRQ 0x70 was not declared for device 2e.7, and coreboot whined about it.
Change-Id: If40aa390722cf253169003129b31f20543fde5dd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39739
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Linux does not handle either value in any special way, though.
Change-Id: I833cb94e65b9ddfb79edbcdd0216c70740aa4a16
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add camera ACPI configuration for Ripto/Volteer
BUG=None
BRANCH=None
TEST=Build and boot Ripto or Volteer. Start camera app and able to
capture images.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I2b47ccd989192273a29f09bf097e12e357929334
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39684
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
This is required for PD notifications on the cros_ec driver.
BUG=b:150649744
TEST=Boot volteer with this patch and verify that PD notifier events are
being generated.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Change-Id: I2e72320b025a3dfa7412181586cb142a4503eda5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use information provided by AGESA to fill the SMBIOS memory tables.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Id73de7c2b23c6eb71722f1c78dbf0d246f429c63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Update Audio AIC UPD settings and gpio pad configs for Tiger Lake.
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I45935b79f6fa4ad66238eead9258a4f15feec508
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39466
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Camera ACPI had an incorrect board config flag for TGL-UP4.
BUG=None
BRANCH=None
TEST=Build and boot TGLRVP-UP3 or UP4. Start camera app and able to
capture images.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Ided0e146a9240169d3f1f27a86218ac1a942b899
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Micron memory part uses SPD Index 0.
BUG=b:152005386
TEST=Build the mainboard.
Change-Id: I990a95b13d636148f0f922fd5c6d4e489d35ed2c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I487fb53bb2b011d214f002fc200ade2f128a4cc6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
1. Configure Audio GPIOs.
2. Set i2c4 configuration.
3. Update PCH HDA configuration
TEST=Verify codecs gets listed with aplay -l command.
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Change-Id: Ic0516c7a8fee79ce17343a7f42895d6ef534fec9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add HID field in max98357a_config and allow mainboards to set it.
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I22d2d078a9a4eb6ab330da8439737ff5133086d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39286
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I005bf205142d4d8c5e12378f33d2100d278fa174
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I78f06b54a6a03d565cf86f1d7bdf37965c3f6ad0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
They are already in AUTHORS.
Change-Id: I315c0c57babfa239e3d7c501a4183b8996999e6e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Updating devicetree to enable ELAN touchpad and ELAN touchscreen on nightfury
BUG=none
BRANCH=firmware-hatch-12672.B
TEST=built and verified touchpad and touchscreen worked
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Change-Id: Ieba6558ce3897ce2f95f51ed667465d84b4ab189
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The VGA port has the DDC on port B.
Select the correct Kconfig and fix graphics init failing on VGA.
Tested on HP Z220, libgfxinit reports success and SeaBIOS is displayed
on the connected VGA monitor.
Change-Id: Ie5ec1a2d4606a21e1dc4217ff6fefe5ee35ac543
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is a µATX mainboard with a LGA1150 socket and four DDR3 DIMM slots.
Working:
- All four DIMM slots
- Serial port to emit spam
- Some USB ports
- Integrated graphics (libgfxinit)
- HDMI and DVI
- Intel GbE
- All PCIe ports
- Both PCI ports behind the ASM1083 PCI bridge
- At least one SATA port
- RAM initialization with MRC binary
- Flashing with flashrom
- S3 suspend/resume
- Rear audio output
- VBT
- SeaBIOS to boot Arch Linux
Not working:
- PS/2 keyboard (detected as mouse)
Untested:
- The other audio jacks
- S/PDIF
- VGA
- EHCI debug
- Front USB headers
- Non-Linux OSes
- TPM header
- Parallel port
Change-Id: I10a16dfc56f2aa88648c8aaaba4feab40c491504
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36770
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adds GMM into the baseboard of Octopus
For GLK, PCI device 3 is GMM according to
Document#: 569262(Glk EDS Vol-1 rev2-7)
Related to Gerrit review 39579
BUG=b:151115705
BRANCH=None
TEST=Flashed final image on Chromebook
Change-Id: I75b4a835c18c5eeb542b7f7b89deea45a31e47bd
Signed-off-by: Franklin He <franklinh@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The integrated BT is routed via USB2 port 8, add USB configuration
to support integrated BT enumeration.
Change-Id: I46d8c92ba57cd72a91ee15ef4d11f07824c29e9a
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I426518e8e18de1c8efcfb7ecb0835df3e257dca1
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39608
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I09cc279b1f75952bb397de2c3f2b299255163685
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I18e513cefc373b1cd70d31d1159928cc948a8476
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
