Age | Commit message (Collapse) | Author |
|
This change reorganizes the CNVi device entries in mainboard
devicetree/overridetree and SoC chipset tree to make it consistent
with how other SoC internal PCI devices are represented i.e. without a
chip driver around the SoC controller itself.
Before:
chip drivers/wifi/generic
register "wake" = "..."
device pci xx.y on end
end
After:
device pci xx.y on
chip drivers/wifi/generic
register "wake" = "..."
device generic 0 on end
end
end
Change-Id: I22660047a3afd5994400341de0ca461bbc0634e2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Terrador and Todor are fanless design, so disable DPTF active policy.
BUG=b:171019363,b:170699797
BRANCH=volteer
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I53a33b8706d7a7d4013a2a5627a620223fcffc3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46874
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO D4 was used for camera reset for both front and rear cameras
(RCAM_RST_L/FCAM_RST_L) in RIPTO. For later volteer versions,
GPIO F15 is dedicated to the rear camera reset (RCAM_RST_L).
Before, BOARD_GOOGLE_VOLTEER flag was used for setting the right
RCAM_RST_L per volteer version. However, we don't support RIPTO
anymore. Also using flags for different volteer version support can
be error-prone. Removing RIPTO support.
BUG=b:171726823
BRANCH=none
TEST=Build and boot volteer proto2 or later version. Camera should
work without an issue.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I961fc17092887b4807c12c95f7139bb7e7b33e91
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46826
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The min86 example SoC code along with the example mainboard
should serve as a minimal example how a buildable x86 SoC code
base can look like.
This can serve, for instance, as a basis to add new SoCs to
coreboot. Starting with a buildable commit should help with
the review of the actual code, and also avoid any regressions
when common coreboot code changes.
As the example code itself is build-tested, it should advance
with coreboot and can't rot like documentation might. It also
serves as a check what APIs need to be implemented with the
default Kconfig settings.
Change-Id: Id76ab15fe77ae3e405c43f9c8677694f178be112
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45710
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The camera privacy LED blinks during the boot and this gives a wrong
impression to the users that the camera is being used during the power
up. The blink happens when the camera module is probed and a series of
kernel patches and coreboot patches are being submitted to resolve the
issue.
The kernel patches are submitted to the chromium gerrit.
https://chromium-review.googlesource.com/2403386
https://chromium-review.googlesource.com/2403387
https://chromium-review.googlesource.com/2403385
https://chromium-review.googlesource.com/2403384
https://chromium-review.googlesource.com/2403383
https://chromium-review.googlesource.com/2403382
https://chromium-review.googlesource.com/2403381
https://chromium-review.googlesource.com/2403380
This is to separate the power resource for the VCM so that it can be
controlled by the driver and suppress the LED turn on.
BUG=b:169049942
BRANCH=none
TEST=Build and boot volteer board. Monitor camera privacy LED
and check if it blinks. It should not blink.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Id51c98e42c5f20e231d8096c9d2d98deebc7c968
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@google.com>
|
|
LTE module Fibocom L850-GL is lost after idle overnight,
with this workaround, host will not initiate U3 wakeup
at the same time with device, which will avoid the race condition.
If this option is set in the devicetree, the bits[7:4] in XHCI MMIO BAR +
offset 0x80A4 (PMCTRL_REG) will be updated from default 9 to 0.
BUG=b:169645448
BRANCH=octopus
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3a04320b0e2441dce540a5afdc461f12de45c41b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
|
|
We all knew this was coming, 32 bits is never enough. Doing this early
so that it doesn't affect too much code yet. Take care of every usage of
fw_config throughout the codebase so the conversion is all done at once.
BUG=b:169668368
TEST=Hacked up this code to OR 0x1_000_0000 with CBI-sourced FW_CONFIG
and verify the console print contained that bit.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6f2065d347eafa0ef7b346caeabdc3b626402092
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45939
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that soc_get_pmc_mux_device() is gone, the PMC MUX connector devices
can be hooked up together via devicetree aliases.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib51764da5b3c029f9ac7ac60199a0aedfc7f29b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45878
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current I2C5 bus frequency is 367 kHZ, which does not meet the spec.
This change updates scl_lcnt, scl_hcnt, scl_hcnt value for I2C5 to bring
the bus frequency closer to 400kHz.
BUG=b:153588771
TEST=Verified that I2C5 frequency is between 389-396kHz.
Signed-off-by: Johnny Li <johnny_li@wistron.corp-partner.google.com>
Change-Id: If0803a74ba9071acf15486ce4038261c1681a92f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Flesh out the PCH configuration into a separate chip. Keep it within the
Broadwell SoC directory for now, to ease moving files around. The boards
were prepared beforehand and the devicetrees require next to no changes.
Tested on out-of-tree Acer Aspire E5-573, still boots.
Change-Id: I28d948f3e6d85e669d12b29516d867c1d1ae9e1a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46700
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
`chip` entries are only hooked up via device nodes to the tree. A `chip`
without a `device` below it does nothing. To allow variants to override
SATA tuning parameters, ensure a device exists under the PCH chip scope.
Without this change, some variants would not properly override the SATA
tuning parameters after extracting the PCH parts into a different chip.
TEST=Sanity-check static.c and verify overridetrees override properly.
Change-Id: I013dbe1403567b93c8ee0e66f76481f2a3f42796
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46769
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, all variants remain identical.
Change-Id: I0fe6de35f7471ce173df40db1444153623544f00
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46705
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, coreboot.rom remains identical.
Change-Id: I75d6594f9576c96a585526c652a070cb9616dbe9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46704
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, all variants remain identical.
Change-Id: I0fa486b8a0fc8be974f37d0bb4eb77a254e8cd86
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46703
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:170604353
BRANCH=volteer
TEST=emerge-volteer coreboot, and boot into kernel.
Change-Id: If354aa158f3ad60193268f38278a44f9c99bf3db
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46770
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the ambassador variant of the puff reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:171561514
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_AMBASSADOR
Signed-off-by: Matt Ziegelbaum <ziegs@chromium.org>
Change-Id: Ib0e3a813a120a4a8e984f3a89dc3ba100d94da95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
List of changes:
1. Split mem_cfg for DDR4 and LPDDR4 as per board_id
2. Move dq_pins_interleaved into board-specific memory configuration
information
TEST=Able to build and boot DDR4 and LPDDR4 ADLRVP SKUs.
Change-Id: I6ef19209767c810426bba0c8bc48178bf2e2a110
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46873
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The LDNs don't have a 0x30 register to enable them. However,
with the devices set to `off`, coreboot won't configure them.
Change-Id: Iaea37c88524904a1dae8a6d3b5f07c6ea25bc3b2
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46021
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop useless writes to read-only registers and don't re-write
default 0x00 values. In detail:
* Don't write read-only status registers.
* Don't try to write input bits in data registers
(iow. mask data values: `data &= ~io`).
* Don't write data registers if all GPIOs are set as
inputs (`io == 0xff`).
* Don't write default 0x00 for inversion and multiplex
registers.
Note: Both GPIO0 and WDT1 values look spurious. Maybe they
were dumped with the virtual devices disabled?
Change-Id: I7d948d6b697285e61e4352b7354b924dbf511e9a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46020
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I8f5a87d006f8bf20af40f7a4f09b1e4b597ba79f
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46019
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It is enabled by the vendor firmware.
Also drop spurious `io 0x60 = 0x00` setting. It's the default anyway
and the resource is kept disabled (it's controlled by the virtual
LDN 2e.008).
This fixes the hang in `PCI: 00:14.3 init` when doing
`outb(0, DMA1_RESET_REG)`.
Fixes: 2f8192bc ("asus/f2a85m_pro: Fix superio type in devicetree")
Change-Id: I351c93033bf2afd824eb6baa8d7625e7a33a295a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I6a16e2f829219f2eba8acd3ae7f371238c0d8de1
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Remove code to turn on backlight during ACPI mode because backlight has
been properly enabled in ACPI.
BUG=b:158087989
BRANCH=Zork
TEST=tested backlight during reboot and suspend
Signed-off-by: Josie Nordrum <JosieNordrum@google.com>
Change-Id: I3bf06042aa19e4559127d611d401f0ba0516b3a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Generate acpi methods which enable and disable backlight during _INI,
_WAK, and _PTS.
BUG=b:158087989
BRANCH=Zork
TEST=check backlight during reboot and suspend
Signed-off-by: Josie Nordrum <JosieNordrum@google.com>
Change-Id: I2f3434dc92de1f697693ff69ca15bd76647b89a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46671
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add internal pull-down for GPP_D19 to improve DMIC noise issue on
nightfury.
BUG=b:171669255
BRANCH=firmware-hatch-12672.B
TEST=Built and checked GPP_D19 voltage after booting
Change-Id: Ie63f260be3d6a55f91908db59312b3b0a8af98f4
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The corresponding devices and objects are already included in the
System Bus ACPI scope inside uncore.asl. There is no need to do this
again in the DSDT of the motherboard.
Change-Id: I98a8d60b585e2eafd76948baea0f249a029bae09
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Rename motherboard_fill_fadt() to the common override
mainboard_fill_fadt() function to override FADT.
Tested=On OCP Delta Lake, verify FADT PM Profile is set to
Enterprise Server.
Signed-off-by: Jingle Hsu <jingle_hsu@wiwynn.com>
Change-Id: Ie9ea7cc6e712d0aca57bbeac1a4154921d123be4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
To support gpio reset SoC, we need to pass the reset gpio parameter to
BL31.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Change-Id: I2ae7684a61af76693605cc0bcf8d20c8992c7bff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46388
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The pins for SD and MMC must be configured properly
so we can access them in payloads.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: Ie6bdffb987d5acf286645550f1c53f294f71c38a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
LTE module Fibocom L850-GL is lost after idle overnight,
with this workaround, host will not initiate U3 wakeup
at the same time with device, which will avoid the race condition.
If this option is set in the devicetree, the bits[7:4] in XHCI MMIO BAR +
offset 0x80A4 (PMCTRL_REG) will be updated from default 9 to 0.
BUG=b:171478764
BRANCH=octopus
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Change-Id: I213fed2b56f216747b2727b69f97d46d8c0c872e
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46701
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
invoke LTE power off function to meet LTE power sequence while DUT is
in reboot state.
BUG=b:167565015
BRANCH=octopus
TEST=build and verify on the DUT with LTE
Change-Id: I825cefb524ddaf9a9cb6add31c2ee0eea484f978
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46022
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, all variants remain identical.
Change-Id: I2b088b36c8e9ff9cbd47d625b14fc45ebd96532a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46702
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:168783630
TEST=Measured the I2C bus frequency reduce to 387 KHz.
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: I9f5b81815f86db7bdcea95a95b9c9b235b4a34b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46613
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The LCM ID is not really used on Jacuzzi followers and the reference
design expects ADC to return 0. However, there were hardware design
issues so the returned value became unexpected numbers.
- Juniper and Kappa returns 1.
- Burnet and Esche returns 1 on normal boot, and 0 on recovery boot.
- Cerise and Stern usually returns 0, and sometimes 1.
To fix that, we are changing LCM ID to fixed value for Jacuzzi followers.
BUG=b:170916885,b:171365301
BRANCH=kukui
TEST=1. emerge-jacuzzi coreboot
2. check burnet/esche skuid correctly
Change-Id: I3b43b9153315ec65e9168c4e84ea844dff14d446
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
1. Enable dptf feature and remove fan control part from overridetree.cb
2. Update tcc offset to 5
3. Follow thermal validation and update PL2 max_power to 51
BUG=b:167931578, b:170357248
Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Change-Id: I99e429b90ed7de08385fe51ca742865b1266eef9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This reverts commit 214c719eed83967b8f0564feca65eebb3d83f5bc.
CB:45857 overrides the GPIO PM configuration if Cr50 does not support
long interrupt pulse width. More recent Cr50 Firmware versions support
long pulse width and hence the GPIO PM can take the default
configuration.
BUG=None
TEST=Build and boot Drawlat to OS. Ensured that 200 iterations of
suspend/resume sequence, warm and cold reboot cycles each are
successful.
Change-Id: I8e3be42cd82fd3ae919d23d6f19c84a90b9c737a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46652
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
Tested=On OCP Delta Lake, log level can be changed via VPD.
Change-Id: I36d4b01b6fb6acc726749641df089cb3f9a4dc3e
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
The dt option `speed_shift_enable` is obsolete now. Drop it.
Change-Id: I5ac3b8efe37aedd442962234478fcdce675bf105
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Enable front camera power in ramstage.
BUG=b:169170677
BRANCH=volteer
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I8b5a9a8333ed518883aa3664a115a4ba2e8a0218
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
Add goodix touch pad as below:
HWID : GXTP7288
CID : PNP0C50
I2C address : 0x2C
I2C speed : 400Khz
HID Descriptor Address : 0x20
BUG=b:171351666
BRANCH=octopus
TEST=build image and verify goodix touch pad working.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Idb4f8d3aff09712dcc98c8ae0c9ae30dc4049e29
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46614
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In deltalake, there's no embedded controller and BMC version is
used to represent ec version.
TEST=Build with CB:45138 and CB:46070
Execute "dmidecode -t 0" to check if the firmware version is correct
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I388efd749170f0ebbb4dd4d32199675d92cc018e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
New SKU ID 5 is used for LTE touch SKU. This patch does LTE power off
for LTE sku and only use Wifi SAR table for non-LTE sku.
BUG=b:168001586
BRANCH=octopus
TEST=Check no SAR table can be loaded with sku id 4 and 5.
Change-Id: Ic0405d3e52aa813bbb1f350966a9e2825e595ce4
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46643
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:161759253
BRANCH=firmware-zork-13434.B
TEST=emerge-zork coreboot chromeos-bootimage
firmware log:
\_SB.I2C2.SEMTECH SX9324: SAR Proximity Sensor at I2C: 02:28
kernel log:
INFO kernel: [ 11.238644] sx932x i2c-STH9324:00: initial compensation success
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I6294ce291365443dd1c4550ba75cb7f33481b889
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45565
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4077b9dfeeb2a9126c35bbdd3d14c52e55a5e87c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45404
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since google_chromeec_cbi_get_board_version and google_chromeec_cbi_get_fw_config both call cbi_get_unit32 and return 0 as success, non-zero as failure. Let's add more readability for the false condition.
BUG=None
TEST=check with empty CBI value
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia49ac1ee35302f8f6afe8c0eb8e13afdf36c5b2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46566
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use PCIE_CLK_NOTUSED in place of 0xFF for unused PCIe ports
BUG=none
BRANCH=master
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I35f2bbce35420fa98541a35f77b14df7440e7980
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
According to the schematic, SRCCLKREQ1# is not connected, so disable it
for terrador and todor.
BUG=b:171278849
BRANCH=volteer
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I5f7734d64390bfadbdb8d152261103adb8e75f40
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
According to the schematic,SRCCLKREQ1# is not connected,so disable it
on voxel.
BUG=b:171279034
BRANCH=volteer
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ibc4f766bd737f30a9ac3c7354d54398e0c36d59d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46612
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Asurada EC is using the large packet (256B) mode, and we were
seeing lots of timeout errors on various commands.
The AcceptTimeoutUs in EC SPI driver is hard-coded at 5000,
and that is too small for large packet running in 1M so we
should change EC SPI to the same value that kernel is using (3M).
BUG=b:161509047
TEST=emerge-asurada coreboot chromeos-bootimage; flash and boot
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Change-Id: I9c47324022129ca23ef75d0c80e215da1692636d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46394
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adding the blank line reduces the differences with the variant
toucan-af.
Change-Id: I58bfc99109a2df2eab54a562dc13e7bd946890d9
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46716
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: If1d4128055a0fd50d109b4aa04c7d0c8ebb2f6c5
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: If58d87296ed6fb176d4bc42ba6f6f39ca069adfd
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Enhance USB 2.0 C0/C1 A0/A1 SI by increasing the level of
"HS DC Voltage Level" and " Disconnect Threshold Adjustment" registers.
COMPDISTUNE0: 0x3->0x7
TXVREFTUNE0: 0x6->0xf
BUG=b:166398726
BRANCH=zork
TEST=1. emerge-zork coreboot
2. check U2 register is set correctly.
3. U2 SI all pass
Change-Id: I69d942605c6d43ece0d71f67df3a5e00b998219b
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46545
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable acoustic noise mitgation for volteer platforms.
BUG=b:153015585
BRANCH=none
TEST= Measure the change in noise level by changing the values
in devicetree.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: I69a6453091bf607d3c5847c99bc077e6b7dbc639
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45053
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the two load line slope settings for the SVID3 telemetry.
AGESA sends these values to the SMU, which accepts them as units
of current. Proper calibration is determined by the AMD SDLE tool
and the Stardust test.
VDD Slope: 62852 -> 62641
SOC Slope: 28022 -> 28333
BUG=b:170531252
BRANCH=zork
TEST=1. emerge-zork coreboot
2. pass AMD SDLE/Stardust test
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: Id831907aa47be27fef2e33bb884a1118ffec14a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The disconnect voltage needs to be adjusted up because the HS DC voltage
level is 0xF.
BUG=b:170879690
TEST=Servo_v4 USB hub functions
BRANCH=zork
Change-Id: If8662015a45c57e457b4593e55af888084842f58
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
RW_LEGACY region needs to be 1 MiB to accommodate any alternate
firmware. Hence update the flash ROM layout as below:
* Grab ~512 KiB from each FW_MAIN_A/B regions and allocate them to
RW_LEGACY region so that it grows to 1 MiB.
* Remove VBLOCK_DEV region which is not used.
* Re-size the ELOG region to 4 KiB since that is the maximum size of the
ELOG mirror buffer.
* Resize RW_NVRAM, VBLOCK_A/B regions to 8 KiB since no more than that
size is used in those regions.
* Resize SHARED_DATA region to 4 KiB since no more than that size is
used in that region.
* Based on the resizing, allocate each FW_MAIN_A/B regions with 72 KiB.
BUG=b:167943992, b:167498108
TEST=Build and boot to OS in Drawlat. Ensure that the firmware test
setup and flash map test are successful. Ensure that the event logs are
synced properly between reboots. Ensure that the suspend/resume sequence
is working fine. Ensure that the ChromeOS firmware update completes
successfully for the boot image with updated flash map and the system
boots fine after the update.
Change-Id: I53ada5ac3bd73bea50f4dd4dd352556f1eda7838
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46569
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To support mipi WFC.
1. enable DRIVERS_INTEL_MIPI_CAMERA/SOC_INTEL_COMMON_BLOCK_IPU
2. add IPU/VCM/NVM/CAM1 in devicetree
BUG=b:163879470, b:171258890, b:170936728, b:167938257
TEST=Build and boot to OS. Capture frames using camera app.
Change-Id: I96f2ef682dff851d7788c2b612765a92228ddf75
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44939
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Andy Yeh <andy.yeh@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable caching of memory training data for recovery as well as normal
mode because memory training is taking too long in recovery as well.
This required creating a space in the fmap for RECOVERY_MRC_CACHE.
BUG=b:150502246
BRANCH=None
TEST=Run power_state:rec twice on lazor. Ensure that on first boot,
memory training occurs and on second boot, memory training is
skipped.
Change-Id: Id9059a8edd7527b0fe6cdc0447920d5ecbdf296e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46651
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the metaknight variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:169813211
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_METAKNIGHT
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Change-Id: Ia2e473eb1d0a2c819b874e497de0823fca75645a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add the Chrome OS specific GPIOs (WP, EC, H1, ...) GPIOs.
BUG=None
TEST=emerge-asurada coreboot; # also boots into emmc
BRANCH=None
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Change-Id: Ieeeee88a09ae4c3af15e2ae93a29684d30dde493
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46386
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure and initialize EC and TPM on Asurada.
BUG=none
TEST=boot asurada
Change-Id: I0f169407d1726899fd0c42e144d907024f036c6a
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46385
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The 0x30 register is eventually controlled by coreboot's
pnp_enable_resources() based on the on/off setting. Other
register settings were grouped with their respective "virtual"
LDN, where possible.
Note, this temporarily breaks LDN 8 settings, as coreboot will
ignore configuration for disabled devices.
Change-Id: I8585dd08eed407ab12258f2accaa63dab294e7d8
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The `io` statement will prepare a 16-bit write, hence use `irq` for
miscellaneous 8-bit registers and fix actual `io` settings (i.e. merge
0x61 writes into 0x60). Note, using `irq` is still just a hack as these
are neither I/O nor IRQs, but it's common practice in coreboot.
Change-Id: I2e1c2286be726d126598cc4a97bb15a57faef42f
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The mainboard has a PS/2 port, so enable the keyboard controller in the
devicetree.
The PS/2 keyboard now works in SeaBIOS payload, but not in GNU/Linux,
probably as ACPI code still needs to be added.
Change-Id: I7846633bc1a3bdf6bffae628e0542bb8fb684804
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Enhance USB 2.0 SI by increasing the level of "HS DC Voltage Level"
and "Disconnect Threshold Adjustment".
COMPDISTUNE0: 0x3->0x7
TXVREFTUNE0: 0x6->0xf
BUG=b:162614573
BRANCH=zork
TEST=1. emerge-zork coreboot
2. check U2 registers are set correctly
3. test with servo v4 type-c, it's working expectedly.
4. U2 SI pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I278cc0aaddbc9fce595bf57ca69ee8abfc9f5659
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46537
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct the two load line slope settings for the SVID3 telemetry.
AGESA sends these values to the SMU, which accepts them as units
of current. Proper calibration is determined by the AMD SDLE tool
and the Stardust test.
BUG=b:168265881
BRANCH=zork
TEST=emerge-zork coreboot
Change-Id: Id6c4f1a92d7f2ad293df7b63694e9665b85f8018
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46472
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Early JSL silicon hang while booting Linux with ISST enabled. The
malfunctioning silicon revisions have been used only for development
purposes and have been phased out. Thus, drop the ISST workaround.
Change-Id: Ic335c0bf03a5b07130f79c24107a1b1b0ae75611
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Currently, the serial console does not work.
With the serial port enabled in the vendor firmware, `superiotool` outputs
the global control register values below.
Found Nuvoton NCT6779D (id=0xc562) at 0x2e
Register dump:
idx 10 11 13 14 1a 1b 1c 1d 20 21 22 24 25 26 27 28 2a 2b 2c 2f
val ff ff ff ff 3a 28 00 10 c5 62 df 04 00 00 10 00 48 20 00 01
def ff ff 00 00 30 70 10 00 c5 62 ff 04 00 MM 00 00 c0 00 01 MM
UART A needs to be enabled in CR 0x2a by clearing bit 7. Do this by
selecting the Super I/O Kconfig symbol `SUPERIO_NUVOTON_COMMON_COM_A`.
This changes the default value 0xc0 to 0x40.
Note, due configuring the system as legacy free with
`HUDSON_LEGACY_FREE=y`, AGESA in romstage disables the LPC controller in
`FchInitResetLpcProgram()`.
coreboot-4.12-3417-g192b9576fe Tue Oct 20 09:15:53 UTC 2020 romstage starting (log level: 7)...
APIC 00: CPU Family_Model = 00610f31
APIC 00: ** Enter AmdInitReset [00020007]
Fch OEM config in INIT RESET
`AmdInitReset() returned AGESA_SUCCESS` is not transmitted anymore. Only
when coreboot enables the LPC controller again in ramstage, serial output
continues.
PCI: 00:14.4 bridge ctrl <- 0013
PCI: 00:14.4 cmd <- 00
PCI: 00:14.5 cmd <- 02
PCI: 00:15.0 bridge ctrl <- 0013
PCI: 00:15.0 cmd <- 00
PCI: 00:15.1 bridge ctrl <- 0013
[…]
done.
BS: BS_DEV_ENABLE run times (exec / console): 0 / 30 ms
Initializing devices...
CPU_CLUSTER: 0 init
[…]
Note, due to incorrect Super I/O configuration in the devicetree, the boot
hangs in `PCI: 00:14.3 init` when doing `outb(0, DMA1_RESET_REG)`. This
will be fixed in follow-up commits.
TEST=Receive (some) coreboot log messages over the serial console.
Change-Id: I0aa367316f274ed0dd5964ba5ed045b9aeaccf8d
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Following commit f50ea988b a couple of symbols are gone, so follow up
that change for this board as well.
Change-Id: I09fd3a107447eb45bb46b7f0f821377943f140b2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46621
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Get rid of legacy pad macros by replacing them with their newer
equivalents.
TEST: TIMELESS-built board images match
Change-Id: I078f9bb3c78f642afc6dcfd64d77be823a4485c2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update PL1 max and min power values
BUG=None
BRANCH=None
TEST=build and verify on dralat system
Change-Id: I75d47fa721576564f71fbd5d5fd2e820fc3f1925
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Configure board specific DPTF parameters for terrador and todor
BUG=b:171019363,b:170699797
BRANCH=volteer
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I19935ca98ec7a078869e73d65ea471df70f37121
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add generic LPDDR4x SPD support for the following three memory
parts:
• K4U6E3S4AA-MGCR
• H9HCNNNBKMMLXR-NEE
• MT53E512M32D2NP-046 WT:F
BUG=b:170264065
TEST=none
Change-Id: Ie3163763a0ce291f27c43181d35c070c218b461d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add devicetree and device ID for P-sensor
BUG=b:161217096
BRANCH=NONE
TEST=We can get the data from P-sensor if touch the SAR antenna.
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: I70f303995b106cca9758b36ebcde112ebcc90950
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update devicetree of boten that enable stylus
BUG=b:160752604
BRANCH=NONE
TEST=build bios and verify function for boten
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: Ifbcac18fcf758f3d870a6af0d1b03e34369414c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
I often find myself having to increase the CBFS size so that TianoCore
fits. Raise the default CBFS size to 2 MiB to alleviate this issue.
Change-Id: I871bb95dee55cc5bad68bb6e71f89ddfa4823497
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46488
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds another X11 series board, the X11SSH-F, which is similiar to
X11SSH-TF but differs in PCIe interfaces/devices, ethernet interfaces.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: I92c32bff861f0b5697aea52ff282fae76b3b78ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Ied350570a695cca1424a6562e41120bcaf467797
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44568
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This Chili mainboard is used in an all-in-one PC.
For more information see
https://www.secunet.com/fileadmin/user_upload/_temp_/importexport/Print/Factsheets/englisch/SINA_Workstation_H_Client_V_Factsheet_EN_Web.pdf
Change-Id: Ic7a5dccbb0d5b7bceb154fb050cf991254475f7b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39995
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Thomas Heijligen <src@posteo.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Chili base board is a ruggedized laptop with additional industrial
interfaces. So far, only booting and basic interfaces (USB, UART,
Video) are working with the original model, the "base" variant.
No further development is planned for this variant, as our primary
target was another one that will be added in a follow-up.
Change-Id: I1d3508b615ec877edc8db756e9ad38132b37219c
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
BUG=b:170703029
BRANCH=octopus
TEST=emerge-octopus coreboot
Signed-off-by: James Chao <james_chao@asus.corp-partner.google.com>
Change-Id: I2bf642963283b8a31a3bd9504c40541ca2f64b34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
There's no need to have multiple Kconfig symbols which do the same
thing. Introduce `SUPERIO_NUVOTON_COMMON_COM_A` and update boards to use
the new symbol. To preserve alphabetical order in mainboard Kconfig,
place the new symbol above the Super I/O symbol (instead of below).
Change-Id: Ic0a30b3177a1a535261525638be301ae07c59c14
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46522
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
No recent Chromebooks have used I2C for TPM communication, and as a
result, a bug has crept in. The ability to extract Cr50 firmware string
is only supported via SPI, yet code in mainboard and vendorcode attempt
to do so unconditionally.
This CL makes it such that the code also compiles for future designs
using I2C. (Whether we want to enhance the I2C protocol to be able to
provide the version string, and then implement the support is a separate
question.)
This effort is prompted by the desire to use reworked Volteer EVT
devices for validating the new Ti50/Dauntless TPM. Dauntless will
primarily be using I2C in upcoming designs.
BRANCH=volteer
TEST=util/abuild/abuild -t GOOGLE_VOLTEER -c max -x
Change-Id: Ida1d732e486b19bdff6d95062a3ac1a7c4b58b45
Signed-off-by: jbk@chromium.org
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
This reverts commit c4a5acdabc28778b49a1c088b0736bac83e2ab51.
Reason for revert: Dalboz is missing pull-up on cmd line, so 400khz is not possible.
TEST=Boot Dalboz
BUG=b:159823235, b:169940175
BRANCH=zork
Change-Id: I89653bfeefa522c17ee2d736215bc22aa445871c
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The camera sensor component chosen for UFC and WFC have an address
conflict. Resolve it by enabling GPIO based I2C Multiplexer. Also
configure the GPIO that is used as select line.
BUG=b:169444894
TEST=Build and boot waddledee to OS. Ensure that the ACPI identifiers
are added for I2C devices multiplexed using I2C MUX under the
appropriate scope.
Change-Id: I9b09e063b4377587019ade9e6e194f4aadcdd312
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable the USB4 retimer driver with GPP_H10 as the power control.
Change-Id: I166bc477f94c159bb411620a6bf77b5d1f194fb2
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
To support camera second source GC5035 for kodama, add world facing
camera id as part of the sku id, which is determined by the data in
camera EEPROM. For models other than kodama, the camera id is always 0
and hence the sku id is unchanged.
BUG=b:144820097
TEST=emerge-kukui coreboot
TEST=Correct WFC id detected for kodama with GC5035 camera
BRANCH=kukui
Change-Id: I63a2b952b8c35c0ead8200d7c926e8d90a9f3fb8
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45811
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new memory.c to support DDR4 memory types.
BUG=b:170604353
TEST=emerge-volteer coreboot chromeos-bootimage
Change-Id: If96b0bda0ce95766f0957c37aa7cbecefc9c03e0
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
There's no need to use static functions to fill these settings in. Also,
add missing include for <stdint.h> and initialize `mem_cfg` in one line.
Change-Id: I82b0997846d4ec40cf9b1a8ebfb1e881b194e078
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46252
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update dptc setting:
Stapm_time_constant 1400
BUG=b:170696020
BRANCH=zork
TEST=emerge coreboot and check "Stapm_time_constant"
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I61d9e00a9d098ad9699b8cf89e70d11de2b95ffd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
The passive clause is constructed with the past participle, which is
*defined* in this case. Fix all occurrences in AMD vendor code with the
command below.
git grep -l "is define at" src/mainboard/ | xargs sed -i 's/is define at/is defined at/'
Change-Id: I5aa0e6e064410b305aa5f2775271f6a8988da64b
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46066
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With a tabulator length of eight spaces, the alignment is the same, but
the other macro definitions are using a space, so do the same for
consistency, better alignment in diff views.
git grep -l -P 'define\tBLD' | xargs sed -i 's,define\tBLD,define BLD,g'
Change-Id: Ib71057c84dc897028cb0ceac29952e67bc541d2e
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch adds some Kconfig hints to make it clearer that the
USE_QC_BLOBS option is required for SC7180 boards and guide the user in
the right direction through menuconfig. Also add those little arrows to
the Trogdor board options that are there on most other boards.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I973cae8026a229408a1a1817c4808b0266387ea7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philip Chen <philipchen@google.com>
|
|
This configuration option shares a name with the FSP UPD, but
is enumerated differently. Change its name to minimise confusion
about the options.
Change-Id: Id74f043ecd549bde4501320bff1dc080bde64057
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Berknip has SSD/eMMC SKU, we should turn off eMMC if storage is NVMe SSD.
BUG=b:170592992
BRANCH=zork
TEST=1. emerge-zork coreboot
2. Check eMMC is enabled or disabled based on the eMMC bit in
FW_CONFIG.
Change-Id: I7aeabc98fc16bc2837c8dcdc40c3c6a80898cdc9
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
TEST=Build and test booting ADL RVP form NVMe and Optane
localhost ~ # lspci -d :f1a6
Show all the NVMe devices and be really verbose
localhost ~ # lspci -vvvd :f1a6
Print PCIe lane capabilities and configurations for all the NVMe devices.
Change-Id: I0a04b23b17df574d4fa3bae233ca40cd3b104201
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
A regular M.2 NVMe SSD shows up on RP9 and runs at x4 width.
Optane memory module shows up as 2 NVMe devices in x2 config:
- NVMe storage device uses RP9
- NVMe Optane memory uses RP11
Note: These two devices are sharing CLK PINs because of same M.2 slot.
TEST=Build and boot ADL RVP board using Intel Optane card.
Change-Id: Ia21d7d2fd07c4fb32291af7bb5a2e41e40316278
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Make PCI ClkReq-to-ClkSrc mapping correct to fix SSD detection issue
on ADL RVP.
TEST=Able to detect WD SSD card over PCH SSD RP9.
Change-Id: I7e26429281f8d3b9edae0f266a5868118369be3f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch programs GPIO for PCH SSD Power Enable (GPP_D16) and Port
Detect (GPP_A12) as per schematics.
TEST=Able to build and boot ADL RVP.
Change-Id: I015e46bdf25437c6b196deb3e610bc1b58726070
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|