| Age | Commit message (Collapse) | Author |
|---|
|
Set tdp_pl1_override to 15 for performance required by the thermal team.
Fix policies.critical index from 2 to 0.
BUG=b:313833488
TEST=emerge-nissa coreboot
Change-Id: I5341bd3d4842f9298a2f5d9e589918bb1b06ba69
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Keeping the PM timer enabled will disqualify an ADL system from entering
S0i3, and will also cause an increase in power during suspend states.
The PM timer is not required for brya boards, therefore disabling it.
Fixes: 0e90580 (soc/intel: transition full control over PM Timer from
FSP to coreboot)
This mirrors an identical commit for google/brya: 1ce0f3aab72d
("mb/google/brya: Fix S0i3 regression")
TEST=Boot Linux on google/drobit, verify S0i3 counter incrementing after
exiting S0ix suspend states.
Change-Id: I644e42388c0f6127512bf52e774b79721601ecc9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80612
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the glassway variant of the nivviks reference board by copying
the template files to a new directory named for the variant.
BUG=b:319071869
BRANCH=firmware-nissa-15217.B
TEST=None
Change-Id: I597666a5be6f71b82c7baddbe343da3d5117dd1c
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Enable DPTF functionality for brox board
BRANCH=None
BUG=b:324360936
TEST=Built and tested on brox board
Change-Id: I0315f7f45688ccc36d321d6be4fa4fac7559a16b
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Select this at the SoC level (like other modern Intel SoCs), and drop
it from individual boards which selected it.
Change-Id: I838ada7dfe948c58a5bb9805ade289b07368aa63
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
It's not needed other than for booting w/SeaBIOS, where it is already
selected by default, and enabling it with edk2 payload prevents Linux/
Windows from fully entering S0ix.
TEST=build/boot purism/librem_cnl (Mini v2), verify Win11/Linux able
to enter and exit S0ix properly.
Change-Id: I974a82bedc4e06f48ce801f2bc0c29afbd80ffcf
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80602
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The tcss.asl doesn't just relate to tcss, it is required for core
scheduling, so include it for all platforms.
Change-Id: I781ba8756e06133799e8d6d91302968cc3ea0a56
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80485
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds support for using ADL N 4-core MCH ID 0x4618.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I3e4855ce93666c54ab35def9b58e4b13bc9a8672
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80488
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The PcieRpEnable option is redundant to our on/off setting in the
devicetrees. Let's use the common coreboot infrastructure instead.
Thanks to Nicholas for doing all the mainboard legwork!
Change-Id: Iacfef5f032278919f1fcf49e31fa42bcbf1eaf20
Signed-off-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79920
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PcieRpEnable option is redundant to our on/off setting in the
devicetrees. Let's use the common coreboot infrastructure instead.
Thanks to Nicholas for doing all the mainboard legwork!
Change-Id: Iea7f616f6db579c06722369c08de7cf7261dece8
Signed-off-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79919
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Probe usb ports by FW_CONFIG setting to disable C1 port on
beadrix poin2 new daughterboard without C1 port.
BUG=b:316365055
BRANCH=firmware-dedede-13606.B
TEST=emerge-dedede coreboot
Change-Id: I494a922d2b04dcf7bd35680f5d95f8463e225f2d
Signed-off-by: Kevin Yang <kevin.yang@ecs.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80573
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Add beadrix supported memory parts in mem_parts_used.txt, generate
SPD id for this part.
1. CXMT CXDB4CBAM-ML-A
BUG=b:321830738
TEST=Use part_id_gen to generate related settings
Change-Id: I3a6925395b52dc7aa5c0f93b8820099369db4dbf
Signed-off-by: Kevin Yang <kevin.yang@ecs.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Now that the baseboard uses chipset devicetree references, remove
all references whose value is identical to the chipset devicetree
default or the baseboard default, since they are pointless clutter.
TEST=build/boot purism/librem_cnl (Mini v2), verify output of lspci
and lsusb unchanged before and after patch.
Change-Id: I12498e7261dafd7ee59fe79926532399392d1b09
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80600
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that the board uses chipset devicetree references, remove all
references whose value is identical to the chipset devicetree default,
since they are pointless clutter.
TEST=build/boot purism/librem_cnl (Mini v2), run lspci and verify output
unchanged before and after patch.
Change-Id: I6c656d227962548cebde61f1d82333837adbbf56
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80599
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select this at the SoC level (like other modern Intel SoCs), and drop
it from individual boards which selected it.
Change-Id: I8ebb915fbc21f82e39304473b0fcaa620559b5d5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80558
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It's already selected at the SoC level, so selecting at the board
level is redundant.
Change-Id: Ifbe7f88858b9e5e8e5185dbff5853186fd3c66cb
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80557
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib7beed7218f317bc2352b65a6191ef1cdaa0742d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Change-Id: Ied455ff29b151fb5f4bca26a189b1d4104d8cede
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80595
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ia2100d26027a7f71739d5445f781b52c517ed966
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80594
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Change-Id: Ib1bbf22480783f63fc2d729b94251e755d2f1720
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80593
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Id859c981d0bf5dcf90bf6858607a9fe726516309
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Change-Id: Ib100a677935cf3309a380952c35e9060e64433cb
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Change-Id: I71dc3dd270b9a61c86b59031f898af37f0fea345
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80590
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the references from the chipset devicetree as this makes the
comments superfluous.
Change-Id: I81dd67fd200768942fe355180b75db0746cda8ea
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
When 'reset_gpio' and 'enable_gpio' properties are defined in
overridetree.cb, the kernel will power on the FPMCU. If the device was
previously enabled the kernel will reset it.
To avoid situation in which the FPMCU is powered on and reset later we
leave the FPMCU powered off in coreboot and started by the kernel. This
is exactly what other boards do (e.g. brya).
TEST=Boot the board (e.g. karis) and make sure the FPMCU was booted once
(e.g. examine FPMCU console logs)
Change-Id: I5df8d9385be2621c02ccee2d36511a4e80ab87d1
Signed-off-by: Patryk Duda <patrykd@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80457
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For devices that require CNVi Bluetooth select WIFI_BT_CNVI
in FW_CONFIG. Discrete Bluetooth devices need to select
WIFI_BT_PCIE.
BUG=b:319188820,b:325084796
BRANCH=None
TEST=Boot image on SKU1,SKU2 and check BT devices enumerate.
Change-Id: Iba008682fcfa7ddc1ec400649c8742c721666f1d
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80564
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Setting the EC interrupt GPIO as an APIC is able to solve many
problems that we are currently seeing:
1. Routing through the APIC make the IRQ# associated with this pin
unavailable to claim for other devices in the kernel. This is causing
EC interrupts to not work.
2. Since EC interrupt are not working, we are not able to flash the
EC from the DUT.
3. Also, the GPI_INT configuration does not allow us to set the
polarity of the GPIO, which means that it is by default set as active
high. As a result, we are seeing an excessive number of host command
interrupts to the EC. This disappears when we change the
configuration to APIC and set the polarity as INVERT.
BUG=b:319129926,b:324707182
BRANCH=None
TEST=1. After boot up, check if ec_cros_lpcs driver was successfully
registered. Look for the following string:
"cros_ec_lpcs GOOG0004:00: Chrome EC device registered"
2. Make sure can flash the EC image from the DUT
3. Make sure EC console is not getting continuous stream of host
commands.
Change-Id: I74bff88d2ddbaf1f4b085c31d582bd66e18c438a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80467
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ashish Kumar Mishra <ashish.k.mishra@intel.corp-partner.google.com>
|
|
Configure PMC mux in devicetree. This allows PD controllers to be
used for both video and power delivery.
Tested on StarBook Mk VI with Ubuntu Lunar, by checking a USB-C PD
display can supply power and display video output.
Change-Id: I580b148b036e62fbcab50d1ca2ab1ed021cfed6b
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77664
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Configure PMC mux in devicetree. This allows PD controllers to be
used for both video and power delivery.
Tested on StarBook Mk VI with Ubuntu Lunar, by checking a USB-C PD
display can supply power and display video output.
Change-Id: I9e49612d7f165a9c9604093535f7b141a4c7048c
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79426
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit 977b8e83cb0a ("mb/emulation/qemu-aarch64: Add MMU support") adds
MMU support for ARM64 QEMU VMs, but registers a limited 1GiB region for
the DRAM, with a note that ramstage should update it.
However on recent versions of QEMU "virt" VMs, accessing RAM outside
this registered region results in an exception even if the address is
backed by actual RAM. This interferes with RAM detection which catches
these exceptions, effectively limiting us to detecting a maximum 1GiB of
RAM even if more is available.
Register the entire RAM space to MMU instead of just the 1GiB, so that
probing RAM addresses can correctly detect how much RAM we have.
Change-Id: I3afbd27b91ab37304a29a62506f965ac3cfb1c06
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
This port is not connected on the X230, X230i, X230t.
When X230 support was introduced and pei_data was filled in, this port
was disabled, but after commit 3dc12c1e1918
(bd82x6x: Consolidate early native USB init) it has become enabled.
Change-Id: I952193798c0894b256b21d9fb3f238074ff5f0f0
Signed-off-by: Alexei Sorokin <sor.alexei@meowr.ru>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80468
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7230bb8f9883f186c10f41132a2919c3fd99f8c1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Change-Id: I245eb8a9961e3e0025c0275f306a4d989b532331
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80491
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I2909375d38c37332293bd7928ae33d5bb502694f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80490
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Vbt data files extracted from dedede recovery image 120.0.6099.272.
Change-Id: I28485d501e519cdaa06c55c20eba07190c5c6b6f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The TCC offset is configured in devtree.c, so remove it from
the devicetree.
Change-Id: I044a68854cc142b057cf31b4e2456d2ad1d0dd3a
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80461
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
There is a modification for the x230 which uses the 2nd DP from the
dock as the integrated panel's connection, which allows using a custom
eDP panel instead of the stock LVDS display.
There are several adapter boards present on the market and all of them
use the same method of enabling the custom eDP panel.
To make this work with coreboot, the internal LVDS connector should be
disabled in libgfxinit. Additionally, VBT has been modified to keep
brightness controls functional on the adapter boards that use LVDS for
the job.
The modifications done to the VBT are:
- Remove the LVDS port entry.
- Move the DP-3 (which is the 2nd DP on the dock) entry to the first
position on the list.
- Set the DP-3 as internally connected.
This has been reported to work with the following panels:
- LP125WF2-SPB4 (1920*1080, 12.5")
- LQ125T1JW02 (2560*1440, 12.5")
- LQ133M1JW21 (1920*1080, 13.3")
- LTN133HL10-201 (1920*1080, 13.3")
- B133HAN04.6 (1920*1080, 13.3")
- B133QAN02.0 (2560*1600, 13.3")
Other eDP panels not on this list should work as well.
Change-Id: I0355d39a61956792e69bccd5274cfc2749d72bf0
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Signed-off-by: Alexei Sorokin <sor.alexei@meowr.ru>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This is the de facto method and should be enforced to keep things
consistent.
Change-Id: I7eee77f7fd49bc38e27cb0e6be0a4a6555098cc7
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Use the new JACK_PRESENCE_DETECT and NO_JACK_PRESENCE_DETECT enums
instead of raw values in the misc field of AZALIA_PIN_CFG.
TEST: Timeless build for clevo/tgl-u did not change
Change-Id: Ic3f4128ecbf89ddce3b6e705ebef76da343a433c
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Eliminates the use of a magic number, and the resulting DID entry in the
_DOD method is the same.
TEST=build/boot google/drallion, dump SSDT and verify DID entry is
unchanged.
Change-Id: Ic929cf7ec6849ba398653226bbe46d27b4e3fa81
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Set the display type for the LCD panel configured via the gfx/generic
driver. This will ensure the correct DID/device address are generated
in the SSDT.
Change-Id: If63374329ed5eb4330517ca1bf2ba1ada24fa54a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80244
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GMA driver generates the brightness controls expecting the name
LCD0, so we need to use it here as well so that the DSDT and SSDT parts
match.
Change-Id: Id52f7c0e542423ba08eeed89bf9b171e540e10e4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80243
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The GMA driver generates the brightness controls expecting the name
LCD0, so we need to use it here as well so that the DSDT and SSDT parts
match.
Change-Id: Id93cfea93edfefc8237b53214734531b811b36e4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80202
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set the display type for the LCD panel configured via the gfx/generic
driver. This will ensure the correct DID/device address are generated
in the SSDT.
Change-Id: I8f390c58710c91bf77555f664e8f89f08ca59b30
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Jinlon disables the eps device if no privacy screen is present, so add
a second generic gfx device 'no_eps' to handle that case, so that ACPI
backlight controls are generated either way. Add logic to ensure only
one of the two devices is active.
TEST=build/boot Win11 on google/hatch (jinlon), ensure LCD backlight
controls present and functional on device both with and without a
privacy screen.
Change-Id: Icf20de97d26c8be76c84e87d5dc6ed1a4b6dbfbc
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80178
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GMA driver generates the brightness controls expecting the name
LCD0, so we need to use it here as well so that the DSDT and SSDT parts
match.
TEST=build/boot Win11 on google/hatch (jinlon), verify LCD brightness
controls are functional.
Change-Id: I4204a518876bed38584260f7566d4d6c9aaa042f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80177
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GMA driver generates the brightness controls expecting the name
LCD0, so we need to use it here as well so that the DSDT and SSDT
parts match.
TEST=build/boot Win11 on google/brya (redrix), verify brightness
controls are functional.
Change-Id: I389553b2ddc5b09d165229e2d8066cacf852b82c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80174
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Won Chung <wonchung@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Redundant when generic gfx driver is used
Change-Id: I8ed1eede05f531f4c76e7fa168c2b92fae7e45cb
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The GMA driver generates the brightness controls expecting the name
LCD0, so we need to use it here as well so that the DSDT and SSDT parts
match.
TEST=build/boot Win11 on google/drallion, verify brightness controls are
functional.
Change-Id: I6fbdd0c5606ec8f2c497e85bf46d388957f15fa5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80175
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Puff-based Chromeboxes use a LSPCON for HDMI 2.0 output, but no driver
exists or is needed for Windows. Use the devicetree hidden keyword to
set the ACPI status to hidden for these devices, to prevent unknown
devices from being listed in Windows Device Manager.
TEST=build/boot Win11 on google/wyvern, verify no unknown devices in
Windows Device Manager for either LSPCON device.
Change-Id: Ib646e01a337b8d7baf20a886c49a8cb64d6408f3
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78040
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add a board-specific VBT file compatible with the latest FSP release
(requires VBT version 250).
TODO: Update all other volteer VBTs to v250 from v240.
TEST=build/boot google/volteer (drobit) with edk2 payload
Change-Id: Ie25a77be5204dfc8b888082492a285973843037c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80183
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Goal is to use existing defines for all pins to make the file
self-documenting, but it would make lines too long, so I'll just
start with the NC pins.
TEST=Timeless binary did not change.
Change-Id: I6da02d7bc4c87cc8477d687b238e6e6c9aec62cd
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79733
Reviewed-by: Nicholas Chin <nic.c3.14@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The name LEDLOGO comes from schematics. It's the red indicator, embedded
in the dot of the 'i' of the ThinkPad logo on laptop's lid.
In vendor firmware, this led starts fading in-and-out, or, in other
words, pulsing, when laptop is put to S3. It helps to determine whether
the laptop is in S3 just by taking a look at the logo.
As of now, coreboot doesn't do anything with this particular indicator,
it's always in enabled (on) state, which is not very convenient.
This patch fixes it.
Tested on T440p.
Change-Id: I85fb69c8c1bed8635a1b31e9b8385c7036bb46dd
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80437
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Nicholas Chin <nic.c3.14@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TCHSCR_RST_L signal was originally being configured to 1 in gpio.c but
this was causing some leakage. Configuring it to 0 initially in
romstage fixes this. Also, make sure that EN_PP3300_TCHSCR is
initialized in romstage as well.
BUG=b:322249892
BRANCH=None
TEST=Make brox boots and touchscreen is still working
Change-Id: I5bf1901a3a40a38237b950abcb758f96aebcc1cf
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80300
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is an existing issue for nissa where wake up from RTC wake is not working during suspend_stress_test.
The phenomenon of the issue is that after pulling out the stylus, can see an interrupt storm occurs, checking through:
"cat /proc/interrupts | grep acpi".
When the counter of interrupt is greater than a certain value, "Disabling IRQ #9" will occur, so RTC wake is not working.
Reference: https://review.coreboot.org/c/coreboot/+/65086
This patch skips the locking for GPP_F15 to allow kernel to
configure it later. The interrupt storm of acpi disappears.
BUG=b:321348117
TEST=1. cat /proc/interrupts | grep acpi
there isn't interrupt storm of acpi when pulling out stylus.
2. The stylus tools panel will pop up when pulling out it.
3. Inserts stylus can wakeup DUT after powerd_dbus_suspend.
4. Passed:
suspend_stress_test -c 2500 --suspend_min=15 --suspend_max=20
Change-Id: Ie143c43e0555d17d8a290f17637b537fba806144
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80316
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
EVT mini-build changes redriver IC from PS8745 to ANX7493, the ANX7493 not support DP AUX BIAS, so connects DP AUX BIAS of DB to SOC directly. Add DB_AUX_BIAS bit field to fw_config for compatibility.
BUG=b:320235566
TEST=DP function of MB and DB workable
Change-Id: I53974ec7444912a63d0fe0a9303c9e5d6941f68d
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80259
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ensure that the SerialIoDevMode config and common_soc_config registers
for each variant are programmed consistently with the devices'
enabled status in that variant's overridetree; remove and disable
extraneous devices as appropriate.
TEST=build/boot several puff variants, verify all components working
as expected, nothing missing from cbmem, lspci, etc.
Change-Id: Ib9d0cf48e405be7c00c553646651fc6f28c4e3f0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80164
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that the puff baseboard uses chipset devicetree references, remove
all references whose value is identical to the chipset devicetree
default or the baseboard default, since they are pointless clutter.
TEST=tested with rest of patch train
Change-Id: Iada32111367fdc964d6126ee43e261c1feb123cf
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Don't enable the i2c controllers, since the variants will enable the
ones they need individually in their overrridetrees.
Disable gspi1 since all variants disable it in their overridetrees.
TEST=tested with rest of patch train
Change-Id: Ia9c67a8e05923a080e31d04721ecae4c810e82e8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Now that puff uses chipset devicetree references, remove all references
whose value is identical to the chipset devicetree default, since
they are pointless clutter.
TEST=tested with rest of patch train
Change-Id: I3a515f13df1252ed2b769a535da22a523c95c359
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80141
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the references from the chipset devicetree as this makes the
comments superfluous.
Change-Id: I06a3acca0a72ff158a0143acc87d9479b2deb0d5
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
This patch selects the DRIVERS_MTK_WIFI and USE_MTCL configs for google/yaviks as
the first platform that provides a country list to the Linux kernel via an
ACPI function (MTCL) in SSDT for MediaTek WiFi chipsets that are capable of
operating on the 6GHz band.
BUG=b:295544553
TEST=Build on similar model (PUJJO) that I have access to and verify the
flag and feature work as intended.
TEST=Add wifi_mtcls.bin blob to cbfs
TEST=Build coreboot for pujjo `emerge-nissa coreboot chromeos-bootimage`
TEST=Verify that MTCL defined in the file is present:
TEST=`acpidump -b`
TEST=`iasl ssdt.dat`
TEST=`less ssdt.dsl`
TEST=Search for MTCL
Change-Id: Iec54fc582d68b443665fceda47187c28f1a9216c
Signed-off-by: David Ruth <druth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80305
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
In case where PAD_CFG_GPI_INT() is initialized with a pin value
lower to PAD_CFG_GPI_IRQ_WAKE() for same GPIO community
the set_ioapic_used() is only called for the PAD_CFG_GPI_IRQ_WAKE() pin.
Due to this the IRQ associated with PAD_CFG_GPI_INT() is found free by
find_free_unique_irq() during IRQ assignment and assigned to other pins
which causes IRQ conflicts
BUG=b:322984217
BRANCH=None
TEST=Boot test on brox, check if correct IRQ assigned to EC
Change-Id: I8c3d557e888b8d0ceac203f49b702910fba26d6d
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80334
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Upload initial GPIO configuration for xol based on proto schematics.
BUG=b:319506033
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
xol proto board can boot to ChromeOS
Change-Id: I224e58628e44571c07ce034136d690587e62be08
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80325
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Upload the initial devicetree and update Kconfig for xol following
proto schematics.
BUG=b:319506033
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot
Change-Id: I411932eb4872d77993394a290e8afdd1a0038faf
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80324
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Remove hardcoded B:D:F numbers for the first socket and pass the PCI
addresses to be locked within SMM by using the smm_pci_resource_store.
This allows to lock down SMM on all sockets without knowing the actual
bus topology or PCI segment group at compile time where the UBOX devices
reside on.
Tested: SMM is locked on all 4 sockets instead of just one.
Change-Id: Ica694911384005681662d3d7bed354a60bf08911
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80247
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the I2C configuration to match the usage such that only required
I2C controllers are enabled.
BUG=b:319390850
TEST=Build Brox BIOS image and boot to OS. Ensure that only the required
I2C controllers are enabled.
Change-Id: I9f24beb9ef587163362cc6ded88efb05be1329b9
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80303
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow reference design rex0, keep the GPIO settings of CNVi/PCIe.
Only set GPP_F04,GPP_F05/GPP_S01,GPP_S02 to NC when
WIFI_PCIE/WIFI_CNVI is selected.
BUG=none
TEST=Build and test on karis
Change-Id: Id23a2cfe0639f2d423980db9badc16c1477434d1
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Update element "KB_TYPE_CA" for align fw_config.
Only EC will reference KB_TYPE field in fw_config. This
CL is just for align fw_config.
BUG=none
TEST=emerge coreboot pass
Change-Id: Ied54f78dddd9dddca1272fc31c9502fc11c61dde
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
|
|
Introduce BOARD_AMD_BIRMAN_PHOENIX_OPENSIL which selects the openSIL
based Phoenix SoC code. Since the Phoenix chip.c is different due to
some FSP-specific data structures in there that are guarded in the
openSIL case, a separate devicetree for the openSIL case is added.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I248102e92818b2d395d561a4bf2627f80906b2f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Rename the BOARD_AMD_BIRMAN_PHOENIX option to
BOARD_AMD_BIRMAN_PHOENIX_FSP to distinguish between the FSP-based SoC
initialization and the non-FSP based one. Also change the
MAINBOARD_PART_NUMBER string to 'Birman_Phoenix_FSP'.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id3293a07cd1b1833df15ee0a40cad3127e19b7df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
The last 'endif' belongs to the 'if BOARD_AMD_BIRMAN_COMMON' in line 26,
so fix the comment. Commit 35a30de7afcc ("mb/amd/birman: Use common
option for variant configuration") changed that condition, but missed
updating this comment, so do this now.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I986e5a456e8f9fd92aacd007479c861feea06199
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
On Brox, HDA Codec used is ALC256. Add verb table for the same. Also,
add the related device tree changes for HDA related registers.
Realtek High Definition Audio Configuration-
Version : 5.0.3.1
BUG=b:317398558
BRANCH=None
TEST=verified HDA on Brox.
HDA Sound cards detected. Headphone working verified.
Device listed under sysfs as below:
cat /sys/bus/hdaudio/devices/ehdaudio0D0/chip_name
ID 256
cat /sys/bus/hdaudio/devices/ehdaudio0D0/vendor_name
Realtek
Change-Id: I1edd5aee053debe39b34048266703031c088cd00
Signed-off-by: Poornima Tom <poornima.tom@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79723
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This renames bus to upstream and link_list to downstream.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I80a81b6b8606e450ff180add9439481ec28c2420
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
GPP_E08 and GPP_E22 were set incorrectly previously.
This CL corrects these settings according to schematics.
BUG=b:305793886
TEST=Built FW image correctly.
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I8e427350e1ee564f9d6566bdfe1f42c92c87a711
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Macros can be confusing on their own; hiding commas make things worse.
This can sometimes be downright misleading. A "good" example would be
the code in soc/intel/xeon_sp/spr/chip.c:
CHIP_NAME("Intel SapphireRapids-SP").enable_dev = chip_enable_dev,
This appears as CHIP_NAME() being some struct when in fact these are
defining 2 separate members of the same struct.
It was decided to remove this macro altogether, as it does not do
anything special and incurs a maintenance burden.
Change-Id: Iaed6dfb144bddcf5c43634b0c955c19afce388f0
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80239
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
With Cr50, the GPIO EC_IN_RW is used to determine whether EC is trusted. However, With the switch to Ti50, it is determined by Ti50's boot mode. If the boot mode is TRUSTED_RO, the VB2_CONTEXT_EC_TRUSTED flag will be set in check_boot_mode(). Therefore in the Ti50 case get_ec_is_trusted() can just return 0.
The current code of get_ec_is_trusted() only checks the GPIO, which
causes the EC to be always considered "trusted". Therefore, correct the return value to 0 for TPM_GOOGLE_TI50.
BUG=b:321172119
TEST=emerge-nissa coreboot chromeos-bootimage
TEST=firmware_DevMode passed in FAFT test
Change-Id: I308f8b36411030911c4421d80827fc49ff325a1b
Signed-off-by: Qinghong Zeng <zengqinghong@huaqin.corp- partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add RAM ID for
H58G66BK7BX067 0 (0000)
BUG=b:322528721
BRANCH=firmware-rex-15709.B
TEST=Run part_id_gen tool without any errors
Change-Id: I31538988d1329d9e2f45d862eb0ae05c0d6a179e
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Check MTL EDS2, SOC_TCHSCR_RST(GPP_C01) default setting is NF1.
Set SOC_TCHSCR_RST to output low in early_gpio_table.
BUG=none
TEST=Build and test on karis, touchscreen function works
Change-Id: Ieebd3cf3c320bc895d036c372f792ec7b5d7ebf9
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Follow reference design rex0, toggles NVMe PWR pin as soon as
in early stage to make NVMe ready sooner.
BUG=none
TEST=Build karis and try warm reboot from OS console. Check the DUT
with WD SSD boots to OS again.
Change-Id: I24a702f02278355c4f2137f0d05c8a9da7cb3c1c
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80213
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current panel voltage measured at mainboard side is 1.79V and the
voltage at panel side is 1.74V. Since the panel requires 1.8V or more,
increase the circuit voltage to 1.9V to meet the panel requirement.
After adjustment mainboard side voltage is 1.89V and panel side is
1.84V.
BUG=b:322080023
TEST=Check ciri vm18 ldo voltage
BRANCH=None
Change-Id: I6d6193d45409f53c0b656890c44ddaef253c5e01
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80198
Reviewed-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ACPI_SCI_IRQ is defined as 9 for all AMD SoCs, so move the definition to
the common amdblocks/acpi.h. Since all but Stoneyridge's soc/acpi.h are
now empty, delete those files too.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8210c98dc4cf2c6001d5273d132053278ff7fea5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80222
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As a result of hardware changes on this board, the PHY previously
routed to the PSE GbE 1 is now routed to PSE GbE 0 on the Elkhart Lake
SoC.
This patch changes the device PCI ID in the board's devicetree and
accordingly, the GPIO configuration.
BUG=none
TEST=Boot into Linux and observe whether both PSE GbE 0 and PCH GbE
are working, while PSE GbE 1 remains inactive (not listed by 'ip link')
.
Change-Id: I322371f944d15134e6f48ecd84a4026c2fced27b
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The currently used panel type could work with 500 ms but increasing
the value to 1 second allows to use a wider range of LVDS LCD panels,
as many of them specify the delay of 1 s as minimum.
The patch has already been made for mc_ehl3 and serves the purpose of
standardization.
commit c0221aa980d3 ("mb/siemens/mc_ehl3/lcd_panel.c: Set LVDS re-power
delay to 1 s")
Change-Id: Ife26ff27b41298ceeed7d9aed0c1ae5553ab5ff8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
This patch enables Cnvi BT Audio Offload feature and also
configures the virtual GPIO for CNVi Bluetooth I2S pads.
BUG=b:303157827
TEST=Build and boot to anraggar. Verify the config from serial logs.
w/o this CL -
```
[SPEW ] -- CNVi Config --
[SPEW ] CNVi Mode= 1
[SPEW ] Wi-Fi Core= 1
[SPEW ] BT Core= 1
[SPEW ] BT Audio Offload= 0
[SPEW ] Pin Muxing
```
w/ this CL -
```
[SPEW ] -- CNVi Config --
[SPEW ] CNVi Mode= 1
[SPEW ] Wi-Fi Core= 1
[SPEW ] BT Core= 1
[SPEW ] BT Audio Offload= 1
[SPEW ] Pin Muxing
```
Change-Id: I9e6731c8ceaad6ee58b525d4246fa769bfe1b0c7
Signed-off-by: Jianeng Ceng <cengjianeng@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80001
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add WIFI SAR table for omniknight.
BUG=b:320172979
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: I70e79577612b3d5c4dc0f92211f87cbea0532d5d
Signed-off-by: jamie_chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80152
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This patch ensures the baseboard and variant configs (inside Kconfig
and Kconfig.name) are organized in alphabetic order.
TEST=execute make menuconfig and verify the google/rex variants
order are alphabetically correct.
Change-Id: I0acc2cec21b4607856127b04c400ec416f0c0dd2
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80206
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the new memory support:
Samsung K4U6E3S4AB-MGCL
BUG=b:320137193
BRANCH=firmware-dedede-13606.B
TEST=Run command "go run ./util/spd_tools/src/part_id_gen/\
part_id_gen.go JSL lp4x \
src/mainboard/google/dedede/variants/galtic/memory/ \
src/mainboard/google/dedede/variants/galtic/memory/\
mem_parts_used.txt"
Change-Id: I3f6c784a194e141a3dd1e5a37b3cf12106e692d6
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80150
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
BUG=b:300690448,b:319393777
BRANCH=None
TEST=tested on a device with i2cdetect
Also tested with evtest and make sure Wacom is listed
Change-Id: I4f528b0d778c8c4a4e83774d5c167ccb2d6afd9a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79895
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is causing an assertion error on the devices that don't have CNVi
enabled because CNVi is hidden behind a FW_CONFIG flag in the
overridetree now.
BUG=b:319188820
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
make sure we can boot to kernel on device.
Change-Id: Ifcfbc04825d4d4e7f2874a4c52f9c5cf3e657856
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80211
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib69236fb5d68272f92405512dc231fa75ecccaa6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch adds APCB blobs to the mainboard directory and it replaces
CB:76445 Also this brings onyx_poc mainboard inline with how APCB are
included in other AMD mainboard: commit 95d05d830162 ("mb/google/zork:
Add and use APCB configuration data"), commit I352f58e0d39 ("mb/google/
skyrim: Add and use APCB configuration data") and commit I1c34528fa0f
("mb/amd/onyx_poc: Add and use APCB configuration data").
BUG=none
TEST=build/boot onyx_poc
Change-Id: I1c34528fa0fd15b847c22c995713078c60ac3873
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80204
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As with other devices with only an external display, the Librem mini/
mini-v2 need a few extra seconds (vs an internal panel) for display init in order for the edk2 boot splash to be visible before the
default boot target is booted.
TEST=build/boot Librem Mini v2 w/edk2 payload, verify splash screen
shown / user has time to enter setup menu.
Change-Id: I9d2d514719a9918ee58cc63969b3adae44ac1632
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
|
|
Alphabetize the ordering of model configs and selects in Kconfig and
Kconfig.name
BUG=None
BRANCH=None
TEST='emerge-brya coreboot' and verify it builds.
Change-Id: Id9347421337d451ce72fcf3984489b06f372f70c
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This change eliminates the unnecessary override of the tcc_offset
chip configuration to 10, as the default rex baseboard now handles
this setting correctly.
TEST=Successfully built and booted google/karis, confirming tcc_offset
remains at 10.
Change-Id: Ie40db1431fb0197ee360ad5656878e57f51c855b
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Follow thermal team request, override tcc_offset to 20.
TEST=Build and verified by thermal team using google/screebo.
Change-Id: Idc76f9c0054f21f066b779e6404a1c175eb396a0
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This CL update setting according to schematic v0.4.
BUG=b:320201111
BRANCH=firmware-rex-15709.B
TEST=Built FW image correctly.
Change-Id: Ia4570d26ee9fd175ed9099bd057cee3c30c95704
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80156
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Looking at photos and service manuals, all the WLAN slots are short
(half-height) and WWAN slots long (full-height).
Change-Id: I894f8216d1b836fbc41423180177bb8651040fbb
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Some variants added the generic gfx driver with an LCD device without
specifying the address, which is required for the backlight controls
to be functional under Windows. Add the address value where missing.
Address value used (0x80010400) is same as on other Brya variants which
did properly set it, and is taken from the ACPI 6.5 spec section B.4.2,
_DOD (display output device enumeration), table B-2:
- bit 31 = use the ACPI-defined (vs vendor-defined) bit scheme for bits
15-0
- bit 16 = platform firmware can detect the device
- bit 10 = display type is internal/integrated flat panel (aka LCD)
TEST=build/boot Win11 on google/brya (osiris), verify ACPI backlight
controls functional.
Change-Id: Id24e330cfb7c993d12665a704e1ca78e2e38874f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
and amplifier
Compatible headphone codec "ALC5682I-VS" and speaker amplifier "ALC1015Q-VB"
BUG=b:183305590
TEST=ALC5682I-VD and ALC1015Q-VB can work normally
Change-Id: I4f212f063a1180d7a1c14769f61b0afef7565cad
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79831
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
