summaryrefslogtreecommitdiff
path: root/src/mainboard
AgeCommit message (Collapse)Author
2024-11-13mb/google/fatcat: Add FW_CONFIG Support for ALC721 soundwireVarun Upadhyay
This change adds support for the ALC721 codec in the device tree and enables it based on the fw_config. BUG=b:368495490 TEST=Boot on google fatcat board Change-Id: If5ca1502942f0ca009db398589c4a243d9e2804c Signed-off-by: Varun Upadhyay <varun.upadhyay@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/85074 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-11-13mb/google/nissa/var/rull: when using pcie wifi7, turn off CNVI BTRui Zhou
When we use PCIE wifi7, CNVI BT and BT offload should be turned off. BUG=b:378053901 BRANCH=None TEST=emerge-nissa coreboot chromeos-bootimage Change-Id: I0adc446220051da59560c9a59d6f334b3a11ac7b Signed-off-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/85044 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kapil Porwal <kapilporwal@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Jayvik Desai <jayvik@google.com> Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-by: Eric Lai <ericllai@google.com>
2024-11-13mb/google/rauru: Pass reset gpio parameter to BL31Yidi Lin
Pass the reset gpio parameter to BL31 to support SoC reset. BUG=b:334753311 TEST=run reboot command Change-Id: I4ddecfb8f36a8f721b57ca16e6a861f933b058b4 Signed-off-by: Yidi Lin <yidilin@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84933 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Reviewed-by: Yidi Lin <yidilin@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-13mb/google/rauru: Configure TPMYidi Lin
1. Add Google Ti50 TPM support 2. Configure I2C speed to I2C_SPEED_FAST_PLUS 3. Pass GPIO_GSC_AP_INT_ODL to the payload 4. Configure IRQ type to IRQ_TYPE_EDGE_RISING for now BUG=b:317009620 TEST=build pass, boot ok and there is no CR50 TPM timeout log Pass log: [INFO ] Probing TPM I2C: done! DID_VID 0x504a6666 [DEBUG] GSC TPM 2.0 (i2c 1:0x50 id 0x504a) Change-Id: I582f010a9033ccb1771dbb3ccab9f16314628796 Signed-off-by: Yidi Lin <yidilin@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84932 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yidi Lin <yidilin@google.com>
2024-11-13mb/google/rauru: Enlarge RW_MRC_CACHE from 8K to 16KJarried Lin
Rauru has MT8196 SoC. Following previous MediaTek SoCs, MT8196 will enable CACHE_MRC_SETTINGS, in order to store the DRAM parameters in the FMAP section RW_MRC_CACHE. As the size of the MT8196 parameters is larger (15968 bytes) compared to previous SoCs (7616 bytes), enlarge RW_MRC_CACHE from 8K to 16K. TEST=Build pass BUG=b:317009620 Change-Id: I35aad5a3a82686a68dd66e993355aa32cc19043e Signed-off-by: Jarried Lin <jarried.lin@mediatek.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/85094 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yidi Lin <yidilin@google.com>
2024-11-12mb/google/fatcat/var/francka: Override DRAM FreqSubrata Banik
Due to the hardware limitation on francka, reduce the memory speed to 7467 MT/s. BUG=b:373394046 TEST=emerge-fatcat coreboot Change-Id: I9c45c90952e20fc96943df03f591075338624e88 Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/85102 Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com> Reviewed-by: Amanda Hwang <amanda_hwang@compal.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2024-11-12mb/google/brox: Do not select HAVE_ACPI_RESUMEKarthikeyan Ramasubramanian
Brox mainboard does not reliably support S3 entry/exit. Hence do not select HAVE_ACPI_RESUME config option. Also trigger a fail-safe board reset if the system resumes from S3. BUG=b:337274309 TEST=Build Brox BIOS image and boot to OS. Ensure that the _S3 name variable is not advertised in the DSDT. Trigger a S3 entry and ensure that on S3 exit, the board reset is triggered. Change-Id: Ief0936fbcd9e5e34ef175736a858f98edf840719 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/85038 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Bob Moragues <moragues@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-11-11via: Start template for VIA C7 w/ CX700 northbridgeNico Huber
The first steps to bring C7 and CX700 support back mainline. Most is skeleton copied from the `min86' example. The romstage entry is placed in the northbridge code, as that's where we'll perform raminit. Support to read the FSB frequency is added right away, same for a reset function (using CF9 reset), as both are required for a minimal build test. A mainboard VIA EPIA-EX is also introduced for build testing, and in later stages boot testing as well. Links: DS: https://theretroweb.com/chip/documentation/via-cx700-datasheet-feb06-666c8b172d347554179891.pdf PM: https://web.archive.org/web/20180616220857/http://linux.via.com.tw/support/beginDownload.action?eleid=141&fid=221 Change-Id: I66f678fae0d5a27bb09c0c6c702440900998e574 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82765 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-11mb/google/nissa/var/rull: Add ELAN touchscreen to devicetreeRui Zhou
Add Elan touchscreen override devicetree for rull based on the latest schematic NB7559_MB_SCH_V1_2024_1010.pdf. BUG=b:374629673 BRANCH=None TEST=1. emerge-nissa coreboot chromeos-bootimage 2. touchpanel function is normal and 'evtest' command displays the touch point Change-Id: Ie7f6dce0175c2940abfa14c4e407414912063112 Signed-off-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/85015 Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-11-11mb/google/var/riven: Optimize the stop delay for touchsreenKapil Porwal
Reduce stop delay for touchscreen based on the latest spec (EKTH6915 Product Spec_V1.0). This will optimize the touch response time to keep the S0ix resume time under 500ms. BUG=b:378012214 TEST=Verify improvement in resume time on Riven. Change-Id: Id7dcbc393bfae9bb62b5700bb9042a543152e968 Signed-off-by: Kapil Porwal <kapilporwal@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/85039 Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-10mb/hardkernel/odroid-h4: Correct number of jacks in hda_verb.cNicholas Sudsgaard
This was found due to the `_Static_assert()` from CB:84360 failing. Change-Id: I401e94b107612f8b7e8a73b3dbc12d7a5227ef01 Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/85076 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
2024-11-10mb/google/fatcat: Fix typo and missing carriage return characterJeremy Compostella
Change-Id: I2b5042795acee3e261765ca4c392d15ef7f5ca96 Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/85020 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
2024-11-10tree: Include static.h for remaining devicetree usagesNicholas Chin
As per commit 865173153760 ("sconfig: Move config_of_soc from device.h to static.h") and commit 05a13e7ed9b9 ("sconfig: Move (WEAK_)DEV_PTR from device.h to static.h"), sources that use code generated from the devicetree should directly include static.h. This allows static.h to be removed from device.h, eliminating many unnecessary dependencies on the devicetree for objects that only need the device types and function declarations. Add static.h to the includes of all remaining files that require static devicetree access through config_of_soc(), the sconfig generated names, or DEV_PTR(). Change-Id: I1d35ff2ac22f9ff5e0aa38b7ad707619e50387f3 Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84591 Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2024-11-10mb/google/*: Explicitly include static.h for DEV_PTRNicholas Chin
As per commit 05a13e7ed9b9 ("sconfig: Move (WEAK_)DEV_PTR from device.h to static.h"), sources that require access to devicetree static devices should directly include static.h. This allows static.h to be removed from device.h, eliminating unnecessary dependencies on the devicetree for objects that only need the device types and function declarations. The DEV_PTR macro resolves to names declared in static_devices.h, which is then included in static.h, so include the header whenever the macro is used. Change-Id: I05662e601af00866b7f26f4c6c6794b491bf676e Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84678 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Jayvik Desai <jayvik@google.com> Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-09mb/google/fatcat: Add ISH support with FW_CONFIG toggleSubrata Banik
This patch adds support for the Integrated Sensor Hub (ISH) on the Fatcat mainboard. ISH can be enabled or disabled via FW_CONFIG bit 24. This allows for flexible configuration depending on the system requirements. The GPIO configuration for ISH is also updated based on CBI settings, ensuring correct initialization and communication. Verified that the device tree correctly probes ISH based on the FW_CONFIG setting: * FW_CONFIG with bit 24 set: ISH is probed successfully. * FW_CONFIG with bit 24 cleared: ISH is not probed. BUG=b:370984186 TEST=Verified ISH probing behavior with different FW_CONFIG settings using CBI. Change-Id: I1a9734139a49be982a7dd43d5afd92e7fea6b29c Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84998 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kapil Porwal <kapilporwal@google.com>
2024-11-08mb/google/rauru: Enable ChromeOS ECYidi Lin
1. Configure ChromeOS EC 2. Pass GPIO_EC_AP_INT_ODL to the payload TEST=build pass BUG=b:317009620 Change-Id: I20828eee93975e75dfb777fe29d5e1c3454b5059 Signed-off-by: Yidi Lin <yidilin@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84931 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Reviewed-by: Yidi Lin <yidilin@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
2024-11-08mb/google/nissa/var/riven: Configure Acoustic noise mitigationDavid Wu
Follow the power team’s recommendation: - Enable Acoustic noise mitigation - Set slow slew rate VCCIA and VCCGT to SLEW_FAST_4 - Set FastPkgCRampDisable VCCIA and VCCGT to 1 BUG=b:376165743 TEST=built firmware and verified by power team, the acoustic noise can be improved a lot. Change-Id: Ia71985ef21d634763fc5ae22e4f611f7f5e9652a Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84908 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Kapil Porwal <kapilporwal@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Jayvik Desai <jayvik@google.com>
2024-11-08mb/google/dedede/var/drawcia: Enable LTR mechanism for PCIe root port 8Robert Chen
Realtek AX generation IC utilizes LTR-issued latency requests to optimize WiFi latency and power consumption, it requires host enabling LTR to meet the design requirement. We enabled the host's LTR by enabling PCIe root port 8, which met resltek's technical requirements. BUG=b:377400590 TEST=Tested on Drawman with RTL8852BE Use command $ lspci -vv, LTR+ is listed on DevCtl2 BRANCH=firmware-dedede-13606.B Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com> Change-Id: I093951f71e971fe83d61d9fcda8bf16cc5f82ffe Reviewed-on: https://review.coreboot.org/c/coreboot/+/85011 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-07mb/google/rauru: Add new board variant HyliaYang Wu
Add a new Rauru follower 'Hylia'. BRANCH=rauru BUG=b:376357839 TEST=emerge-rauru coreboot chromeos-bootimage Change-Id: I79c4525347fd7b1ecea6df05e1a6b726b78e946f Signed-off-by: Yang Wu <wuyang5@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84924 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yidi Lin <yidilin@google.com>
2024-11-07mb/dell: OptiPlex 3050 Micro port (Intel KabyLake)Mate Kukri
- Boots Linux 6.11 (Debian) - GRUB and SeaBIOS payloads work - SMSC SCH5553 SIO/EC + Serial port works + PWM fan control works - Realtek Gigabit LAN works - WiFi slot works - NVMe SSD slot works - Extra: LPSS UART0 + Stock FW sets undocumented power gating bit, RTC battery needs to be pulled for it to work. + Signals exposed on test points on the back of the board. FIXME: add documentation about this - Needs 'deguard' to bypass BootGuard + See https://review.coreboot.org/admin/repos/deguard,general - Audio works - All USB ports work - Currently limited to the Micro form factor, but others are very similar - HDA verbs and VBT by Leah Rowe Change-Id: I8d443e39ee684a4eaa19c835a945cfe569c051e2 Signed-off-by: Mate Kukri <kukri.mate@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82053 Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2024-11-07mb/cwwk/ald: Remove DIMM_MAXArthur Heymans
For ADL DIMM_MAX is a soc property and not a mainboard property. Change-Id: I834b631ffb9b7b2272ec631122de61136e55651a Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84207 Reviewed-by: Alicja Michalska <ahplka19@gmail.com> Reviewed-by: Elyes Haouas <ehaouas@noos.fr> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-07mb/google/nissa/var/rull: Add Fn key scancodeRui Zhou
The Fn key on rull emits a scancode of 94 (0x5e). BUG=b:372211281 TEST=Flash rull, boot to Linux kernel, and verify that KEY_FN is generated when pressed using `evtest`. Change-Id: Idb02d7013fa78233abff556bc6fa1d224c434338 Signed-off-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/85014 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Lei Cao <caolei6@huaqin.corp-partner.google.com> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-11-07mb/google/nissa/var/rull: Change padbased_override to rtd3 of wifiRui Zhou
The previous method made cnvi wifi6 configuration cumbersome and unusable. And delete unused pins. We abandoned the fw_config judgment method and changed to the better rtd3. BUG=b:374629673 BRANCH=None TEST=1. emerge-nissa coreboot chromeos-bootimage 2. wifi7&wifi6 function is normal Change-Id: Ia95dc9f6b707db63840de9b15b38bdaea48ea192 Signed-off-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/85000 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jayvik Desai <jayvik@google.com>
2024-11-07mb/google/nissa/var/rull: add touchpad init config of Synaptics&PIXARTRui Zhou
Add Synaptics&PIXART init cpnfig, enable touchpad function BUG=b:374629673 BRANCH=None TEST=1. emerge-nissa coreboot chromeos-bootimage 2. touchpad function normal Change-Id: Iacf09cd46d4a97fb79f91043c84452f76689462f Signed-off-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84999 Reviewed-by: Lei Cao <caolei6@huaqin.corp-partner.google.com> Reviewed-by: Jayvik Desai <jayvik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-11-07mb/google/nissa/var/rull: add ssd timing and modify ssd GPIO pins of rtd3Rui Zhou
The previous GPIO config will cause the SSD device to not be recognized. Based on schematics NB7559_MB_SCH_V1_2024_1010.pdf. So we adjust the position of the enable and reset pins. BUG=b:374629673 BRANCH=None TEST=1. emerge-nissa coreboot chromeos-bootimage 2. power on proto board successfully Change-Id: Idb36f67206450612655cb3efd3cce240475ef3ab Signed-off-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84997 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-11-07mb/gigabyte/ga-h77m-d3h: Add Sandy/Ivy Bridge board GA-H77M-D3HFabian Groffen
This board is based off ga-b75m-d3h, which uses the same SuperIO chip. It doesn't have the ASMedia SATA3 controller, the H77 chipset comes with 2 SATA3 ports next to the 4 SATA2 ports. Flashing notes: These boards come with dual-BIOS feature. This is set of two unremovable what appears to be identical chips marked M_BIOS and B_BIOS. Flash the B_BIOS chip, and boot the system. Ensure you have a payload and setup ready to boot a Linux system with iomem=relaxed or similar. Immediately use flashrom -p internal to flash the same firmware again. If you skip this step your next boot will show weird exception traces in either coreboot or your payload. Flashing from there via the chip is very difficult (you have to try many times in order to get a booting run), which can all be remedied by doing a flash from internal. I suppose the dual-BIOS feature is somewhat in the way here. Tested with: - CPU Core i7-3770S - RAM single bank 4GB CL11, two banks 4+4GB CL11 - OS Gentoo Linux LiveUSB, KDE desktop (Linux 5.15.72) Working: - GRUB2 payload - Intel ME stripped - Integrated graphics with libgfxinit - (boot from) SATA2, SATA3 ports - Rear and mainboard connector USB ports, supporting boot - Atheros GbE NIC - 2.0 channel audio via lineout jack output - ACPI (power button triggers OS events) - S3 suspend/resume - PWM FAN control, FAN speed readings - Temperature sensor readings Signed-off-by: Fabian Groffen <grobian@gentoo.org> Change-Id: Icb3e74326a0a7aaf770d1917a2a0931feadd7eab Reviewed-on: https://review.coreboot.org/c/coreboot/+/77046 Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-07mb/asrock: Add Asrock Industrial IMB-1222 motherboardMaxim Polyakov
ASRock IMB-1222 Intel Comet Lake-S Q470E industrial thin mini-ITX motherboard [1]. Working: - Dual Channel DDR4 2933/2666/2400 MHz; - Intel UHD Graphics (VGA Option ROM, libgfxinit, GOP driver); - DP (both), HDMI; - PCIe x16 Slot (Gen3); - SATA ports; - USB 2.0 ports; - USB 3.2 ports; - M.2 Key-E 2230 slot for Wireless (PCIe x1, USB 2.0 and CNVi); - M.2 Key-B 3042/3052 slot for 4G/5G modem (PCIe x1); - M.2 Key-M 2242/2260/2280 for SSD/NVMe (PCIE x4, SATA3); - LAN1 Intel I225LM/I225V, 10/100/1000/2500 Mbps; - LAN2 Intel I219LM, 10/100/1000 Mbps; - Realtek ALC887 HD Audio (line-out, mic-in); - COM 1/2/3/4 ports; - onboard speaker; - HWM/FANs control (fintek f81966); - S3 suspend and wake; - TPM; - disabling ME with me_cleaner [2]; Payload: - Linux as payload; - LinuxBoot; - SeaBIOS; - edk2 [3]. Bootable OS: - Ubuntu 22.04 (Linux 6.5.0-15-generic); - Ubuntu 24.04 (Linux 6.8.0-41-generic); - Microsoft Windows 10 Pro (10.0.19045.4780, 22H2 2022); - Andoid 13, Bliss OS x86_64 (16.9.7, Linux 6.1.112-gloria-xanmod1). Unknown/untested: - USB3.0 in M.2 Key-B 3042/3052 slot; - eDP/LVDS; - PCIe riser cards; - SPDIF. There is no schematic/boardview, reverse engineering only. This port is based on system76/bonw14 because it has a similar topology. [1] https://web.archive.org/web/20220924171403/https:// www.asrockind.com/en-gb/IMB-1222 [2] XutaxKamay's me_cleaner fork, https://github.com/XutaxKamay/me_cleaner, v1.2-9-gf20532d [3] MrChromebox's edk2 fork, https://github.com/mrchromebox/edk2 uefipayload_2408 branch Change-Id: Id2b4c903546f9174b5e7dd26e54a0c5aaa09e1f8 Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83107 Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-06mb/google/brox: Hint romstage init about upcoming resetKarthikeyan Ramasubramanian
Add support for the mainboard to check for any potential firmware component update and hence the assosicated reset. This indication can be used to avoid any redundant resets during the boot flow. BUG=b:375444631 TEST=Build Brox BIOS image and boot to OS. Ensure that the hints are provided correctly and 2 redundant resets are filtered out. Change-Id: Ieed3f9013dee9aa501a3f0403f3a28722a3878f1 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84937 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-11-06mb/google/brox: Reduce PL4 only for battery disconnected scenarioSowmya Aralguppe
This patch reduces PL4 only for no battery condition i.e. when battery is disconnected or not physically present. BUG=b:377305625 TEST=Build Brox and boot when the battery is disconnected Change-Id: I59a1028ce9cd3a6cf98f865d9c085a64f391f201 Signed-off-by: Sowmya Aralguppe <sowmya.aralguppe@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/85002 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2024-11-06mb/google/dedede/var/awasuki: Enable LTR mechanism for PCIe root port 8Hualin Wei
Realtek AX generation IC utilizes LTR-issued latency requests to optimize WiFi latency and power consumption, it requires host enabling LTR to meet the design requirement. We enabled the host's LTR by enabling PCIe root port 8, which met resltek's technical requirements. BUG=b:366383364 TEST=Tested on Awasuki with RTL8852BE Use command $ lspci -vv, LTR+ is listed on DevCtl2 Change-Id: I0c80f89b4fdb52a5d9da17548537072ec2d40418 Signed-off-by: Hualin Wei <weihualin@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84951 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2024-11-06mb/google/dedede/var/drawcia: Update ext_vr for board version > 0xbRobert Chen
ext_vr_update should be run after board version 0xb, but skipped by return. Drawper LTE board version was set after 0x9, but there are more board added after that. Specific Drawper board version as 0xa, 0xb and 0xf. BUG=b:376828839 BRANCH=firmware-dedede-13606.B TEST=emerge-dedede coreboot chromeos-bootimage and test on DUTs. Change-Id: I13f4709b6f490169f69054cf2b26430b4de0746a Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84953 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Derek Huang <derekhuang@google.com>
2024-11-06mb/intel/coffeelake_rvp/cml_u: Correct number of jacks in hda_verb.cNicholas Sudsgaard
This was found due to the `_Static_assert()` from CB:84360 failing. As I do not own this board, I cannot test whether is change is "functionally correct". However, I believe it is more likely that the original authors forgot to update the verb table size, rather than them adding additional verb data which was not meant to be used. TEST=`_Static_assert()` mentioned above does not fail anymore. Change-Id: I8df44e056bc841bfb344749ba214e6fb71a1955b Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84487 Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-06mb/google/nissa/var/glassway: Add initial LTE related settingsDaniel Peng
1. Add DB_1C_LTE 4 on DB_USB fw_config. 2. Implement WWAN power sequencing. 3. Disable LTE-related GPIOs based on fw_config. 4. Add I2C SX9324 (P-sensor) support. Refer Schematic file: CA31AC_R10_MB_SUB_240903A_P.pdf BUG=b:374666995 BRANCH=firmware-nissa-15217.B TEST=emerge-nissa coreboot chromeos-bootimage Confirm the device node i2c-STH9324:00 created correctly, and command for # i2cdump -f -y 11 0x28 is workable. Change-Id: Ida56ff338d82f48aef419a65830a3380c83123d5 Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84925 Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
2024-11-06soc/mediatek/mt8196: Disable irq2axi featureRunyang Chen
Irq2axi translates wire-based interrupt into message signal interrupt. Since MT8196 uses legacy wire-based interrupt, this feature needs to be disabled. If the interrupt is not handled, it will cause the system fail to boot. TEST=Build pass, check irq2axi_disable log and the interrupt can be correctly handled by checking /proc/interrupts. BUG=b:317009620 Signed-off-by: Runyang Chen <runyang.chen@mediatek.corp-partner.google.com> Change-Id: I0e89a0ee75e574a4b9e8df0a0f6a5f6e03bba2d6 Reviewed-on: https://review.coreboot.org/c/coreboot/+/84896 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Reviewed-by: Yidi Lin <yidilin@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-06mb/google/rauru: Complete PCIe reset in romstageYidi Lin
De-assert PERST# at romstage to reduce the waiting time in ramstage. BUG=b:361728592 TEST=The boot time improves 62ms Change-Id: I2cd5cd59e7513b6e4036c3e8013a3c7322d2f787 Signed-off-by: Yidi Lin <yidilin@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84895 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Reviewed-by: Yidi Lin <yidilin@google.com>
2024-11-06mb/cwwk/adl/devicetree: correct PCIe RP 12 clock configurationFelix Held
Looking at Intel document 759603 revision 001, Alder Lake N only has 5 PCIe clock outputs and clock request pins. I only have the version 2 of this board which has a significantly different USB port configuration to version 1, but there the Ethernet controller on RP 11 and the E key m.2 slot on RP 12 share the last PCIe clock output. The on-board TUBF0304 clock buffer chip takes the clock output form the last PCH PCIe clock generator output and drives the clock inputs of both the last Ethernet chip and the E key m.2 slot. Since the last clock output is always active, since RP 11 has the PCIE_RP_CLK_REQ_UNUSED flag set, using the non-existent clock output and request for RP 12 didn't break things. ASPM L0s might still work though, since that one doesn't involve switching off the PCIe reference clock, but haven't tested that yet. Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: I103f7c3fe0b806f5c0a5202b8221f522a4b1c378 Reviewed-on: https://review.coreboot.org/c/coreboot/+/83911 Reviewed-by: coreboot org <coreboot.org@gmail.com> Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-05mb/lenovo: Add ThinkCentre M920q (Coffee Lake)Maciej Pijanowski
It may come with 8th or 9th Gen CPUs. i5-8500T has been tested here. Works: - Serial adapter from daughter board (COM1 connector) - USB ports front and back - USB-C port (charging, data) - HDMI - Ethernet - SATA - NVMe - internal speaker - TPM2.0 - PCIe x8 port (x8 riser tested, x4 not) Does not work: - front audio jacks Change-Id: Iea1dc5745c0ecf687fa18b793f0aab4b0855d6d4 Signed-off-by: Maciej Pijanowski <maciej.pijanowski@3mdeb.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80609 Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-05mb/google/nissa/var/glassway: Add touch screen ILIT2901 supportDaniel Peng
1. Extend 1 bit [34] for the TOUCHSCREEN_SOURCE. SSFC range for TOUCHSCREEN_SOURCE is bit[32:34]. 2. Touchscreen panel: MUTTO A153728S1Y, and set TOUCHSCREEN_ILIT2901 to value "4" 3. Datasheet: #153728S1V1.0 SPEC_20240923.pdf BUG=b:375986645 BRANCH=firmware-nissa-15217.B TEST=1. emerge-nissa coreboot chromeos-bootimage 2. Confirm command evtest and touchscreen function is workable. Change-Id: I6e13c948edca5a894e1a00a1954f0f88c4a079cf Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84894 Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Jayvik Desai <jayvik@google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-04mb/google/fizz: Fix USB port defintionsMatt DeVillier
commit 6c83a71b0a80 ("skl mainboards/dt: Move usb{2,3}_ports settings into XHCI device scope") not only moved the USB port definitions under the XHCI device reference, but also combined multiple register definitions. In doing so, it broke the inheritance from the baseboard, since the variant overridetree registers now replaced the entire usb2_ports/usb3_ports structs, rather than replacing individual array elements therein. This resulted in any USB ports inherited from the baseboard and not overridden by the variant being non-functional as they were not included in the resulting combined devicetree. To fix this, return to overriding individual array elements in the usb2/3_ports structs. TEST=build/boot google/fizz/var/karma. Verify all USB ports present and functional. Verify mainboard/static.c in built shows all ports. Change-Id: I0e80bf4949a857c21d44537eb720a7a8a7db2f80 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84955 Reviewed-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-04mb/google/fatcat/var/fatcat: Configure eSPI alarm GPIOSukumar Ghorai
This patch configures the ESPI_SOC_ALERT_L GPIO pad on fatcat as NC to enable S0ix low power entry. TEST=Build fatcat and check the platform boots without an issue. Change-Id: Icb80a56177105c0281d05fe1f5daa87e6f7e291f Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84957 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
2024-11-04mb/google/fatcat: Disable package c-state auto-demotionSukumar Ghorai
Package C-state auto demotion feature allows hardware to determine lower C-state as per platform policy. Since platform sets performance policy to balanced from hardware, auto demotion can be disabled without performance impact. TEST=Build fatcat and check the platform boots without an issue. Change-Id: I01f2cb8ac1093ae98cc076e35ad1924baa53aa59 Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84956 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-11-04mb/google/dedede/var/awasuki: Tune I2C touchpad for freq and THWei Hualin
1. Modify the I2C frequency of the touchpad between 380 Khz and 400 Khz to meet the spec. 2. Increase clk the time of high (TH) to greater than 600ns. Before: I2C0 - 420KHz TH - 557ns After: I2C0 - 398Khz TH - 630ns BUG=b:351968527 TEST=Check that the wave form meets the spec. Change-Id: I5ccaa3a669e18319311de14833966410c7adf40d Signed-off-by: Hualin Wei <weihualin@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84898 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
2024-11-04mb/google/fatcat/var/francka: Generate RAM ID for MT62F2G32D4DS-020 WT:FAmanda Huang
Add Micron part MT62F2G32D4DS-020 WT:F only for Francka. DRAM Part Name ID to assign MT62F2G32D4DS-020 WT:F 0 (0000) BUG=b:373394046 TEST=emerge-fatcat coreboot Change-Id: I2de56c8c7a028edefbd3dc53f8b1e26dee3286f7 Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84781 Reviewed-by: Pranava Y N <pranavayn@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-02mb/google/fatcat: Add devicetree for MAX98357A codecAnil Kumar
Update device tree to support speaker o/p on MAX98357A AIC. BUG=b:357011633 TEST=build coreboot image and test audio playback on Google/Fatcat board. Signed-off-by: Anil Kumar <anil.kumar.k@intel.com> Change-Id: I20de87f673e947f0e2332b818ebca01c0fa5e200 Reviewed-on: https://review.coreboot.org/c/coreboot/+/84888 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-11-01mb/google/brya/var/banshee: select SOC_INTEL_RAPTORLAKEIan Feng
Select SOC_INTEL_RAPTORLAKE to force coreboot to use the RPL FSP headers for FSP as banshee is using a converged firmware image. This effort also helps to save banshee boot time by 80-100ms as RPL FSP is better optimized. Additionally, Raptor Lake platform only needs 1 SIPI-SIPI which saves 10ms of the boot time. BUG=b:358254132 TEST=Able to build and boot google/banshee. cold boot time w/o this CL ``` Total Time: 1,399,888 ``` cold boot time w/ this CL ``` Total Time: 1,295,334 ``` Change-Id: If22e07a4c1b35fe1d060ca523743c6c503937287 Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84949 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
2024-11-01mb/google/nissa/var/riven: Increase the VccIn Aux Imon IccMax to 30ADavid Wu
From power team's recommendation, increase the VccIn Aux Imon IccMax to 30A to meet HW settings. BUG=b:376306118 TEST=Build firmware and check the value is changing as expected. Paste the firmware log. [SPEW ] VccInAuxImonIccImax= 0x78 [SPEW ] (MAILBOX) VccInAuxImonIccImax = 120 (1/4 Amp) [INFO ] Override VccInAuxImonIccImax = 120 Change-Id: I71020c2f631cb517a52d4bb65e35277eb731ced7 Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84922 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Zhuohao Lee <zhuohao@google.com> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-10-31mb/google/rauru: Pre-initialize PCIe at the bootblock stageJianjun Wang
According to the PCIe CEM specification, the deassertion of PERST# should occur at least 100ms after the assertion. Right now we simply wait for 100ms in ramstage for that. To speed up the boot time, pre-initialize PCIe by asserting PERST# earlier in the bootblock stage. The pre-initialization time is stored in the early init data region, so that the PCIe initialization in ramstage could make sure the required 100ms delay is still reached. This pre-initialization will speed up the boot time by 100ms on rauru. TEST=Build pass, show pcie init pass log: mtk_pcie_domain_enable: PCIe link up success (1) BUG=b:317009620 Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com> Change-Id: I2b84c25ae3ea9069fd38fa6b20b8235a7fc3a484 Reviewed-on: https://review.coreboot.org/c/coreboot/+/84699 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yidi Lin <yidilin@google.com> Reviewed-by: Yu-Ping Wu <yupingso@google.com>
2024-10-31mb/google/nissa/var/teliks: Match VBT with SSFCzengqinghong
We want to configure different VBT timings for panels of different sizes and distinguish them through SSFC. We select the reserved bit 6 of SSFC as the flag bit. When using a 12-inch panel, set this bit to 0; when using an 11-inch panel, set this bit to 1. Without splitting, the platform_BootPerf test will fail. BUG=b:374428465 TEST= 1. can match VBT with SSFC -When SSFC is set to 0x40: $ cat /sys/firmware/log | grep vbt Bit 6 of SSFC is 1, use vbt-teliks_panel_11_inch.bin CBFS: Found 'vbt-teliks_panel_11_inch.bin' @0x1c6140 size 0x50f in mcache @0x76adda14 -When SSFC is set to 0x0: $ cat /sys/firmware/log | grep vbt Bit 6 of SSFC is 0, use vbt-teliks.bin CBFS: Found 'vbt-teliks.bin' @0x1c5bc0 size 0x50e in mcache @0x76add9b0 2. can pass platform_BootPerf test The platform_BootPerf time measured for all SKUs is less than 1.55s. Change-Id: Ia8fb45aede5ead4826d983760506c366a70643ee Signed-off-by: Qinghong Zeng <zengqinghong@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84871 Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jianeng Ceng <cengjianeng@huaqin.corp-partner.google.com> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-10-31mb/google/fatcat: Adjust EC host command range for microchip ECSubrata Banik
This commit adjusts the EC host command range for the Fatcat board to 0x800-0x807 & 0x200-0x20f. This change is necessary because the microchip EC used on the Fatcat board has a smaller host command range than the ITE/Nuvoton ECs used on other Fatcat variants. The `gen1_dec` register in the devicetree is updated to reflect this change. As per boot log, the `gen1_dec` aka offset 0x84, base address is 800 and size is 8 bytes. AP FW Boot log: [SPEW] PCI: 00:00:1f.0 resource base 800 size 8 align 0 gran 0 limit 0 flags c0000100 index 84 BUG=b:376207365 TEST=Able to build and boot google/fatcat w/o any error. without this patch: [SPEW ] LPC: Trying to open IO window from 800 size 8 [ERROR] LPC: Cannot open IO window: 800 size 8 [ERROR] No more IO windows with this patch: [SPEW ] LPC: Trying to open IO window from 800 size 8 Change-Id: Ifcee533341fa583d841a4b564f25831c6d04e951 Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84919 Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Pranava Y N <pranavayn@google.com> Reviewed-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
2024-10-30mb/google/fatcat: Define EC_SYNC_IRQ and GPIO_PCH_WP for variantsSubrata Banik
This commit defines the EC_SYNC_IRQ and GPIO_PCH_WP macros for different Fatcat variants. The EC_SYNC_IRQ macro is used for tight timestamps and wake support, while the GPIO_PCH_WP macro is used for the WP signal to the PCH. These macros were previously undefined or incorrectly defined for some variants. This commit fixes these issues and ensures that the macros are defined correctly for all variants. Specifically, this commit: - Defines EC_SYNC_IRQ and GPIO_PCH_WP for Fatcat Nuvo and Fatcat ITE. - Defines EC_SYNC_IRQ as 0 (not connected) for Fatcat. - Defines GPIO_PCH_WP as GPP_D02 for Fatcat. - Leaves EC_SYNC_IRQ and GPIO_PCH_WP as 0 (TODO) for Francka. TEST=Able to build and boot google/fatcat. w/o this patch: ``` cros_ec_lpcs GOOG0004:00: couldn't retrieve IRQ number (-22) cros_ec_lpcs GOOG0004:00: probe with driver cros_ec_lpcs failed with error -22 ``` w/ this patch: ``` cros_ec_lpcs GOOG0004:00: Chrome EC device registered ``` Change-Id: I9bd248496f08869c08cf6daafeed6584d0b166b7 Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84900 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Pranava Y N <pranavayn@google.com>
2024-10-30mb/google/fatcat: Ensure RW_SECTION_B at 16MB boundary for debug FMDSubrata Banik
This patch updates the flash map layout to guarantee that the RW_SECTION_B section starts at the 16MB boundary. Additionally, fix typo in flash descriptor comment, where comment incorrectly referred to "MTL" instead of "PTL". TEST=Successfully builds google/fatcat. Change-Id: Ia6dba611fba50f9694a75670d954a4630cde4d70 Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84899 Reviewed-by: Pranava Y N <pranavayn@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-28mb/google/nissa/var/telith: Modify touchscreen form ILITEK to ELANKun Liu
When creating variant, it was copied from teliks, and according to the requirements of telith project, update the override devicetree to use ELAN touchscreen. BUG=b:373510302 BRANCH=None TEST=1. emerge-nissa coreboot chromeos-bootimage 2. power on proto board successfully 3. touchscreen is functional Change-Id: If0da85a38f3a68b6f50cfd096a628174b313fcc9 Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84865 Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-10-28mb/google/brya: Create rull variantRui Zhou
Create the rull variant of the nissa reference board by copying the template files to a new directory named for the variant. And based on schematics NB7559_MB_SCH_V1_2024_1010.pdf update devicetree settings. (Auto-Generated by create_coreboot_variant.sh version 4.5.0) BUG=b:374673463 BRANCH=None TEST=util/abuild/abuild -p none -t google/brya -x -a make sure the build includes GOOGLE_RULL Change-Id: If48273f3e9db69507b41ea0313916d94ecabe309 Signed-off-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84828 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Eric Lai <ericllai@google.com>
2024-10-28mb/google/fatcat/var/fatcat: Enable iGPU display using FW_CONFIGSubrata Banik
This change enables the integrated GPU (iGPU) display on the Fatcat board based on the FW_CONFIG setting (specifically the DISPLAY bit). By conditionally probing the display based on FW_CONFIG, the iGPU is dynamically enabled or disabled according to the SKU configuration. TEST=Verified display functionality on Fatcat with the iGPU: > cbi set 6 0x58A814 4 (DISPLAY_ABSENT): - lspci does not list the iGPU. - No display output, but the device boots to the OS (verified via console). > cbi set 6 0x5CA814 4 (DISPLAY_PRESENT): - lspci lists the iGPU. - Display output is functional, showing firmware and OS UI. Change-Id: I5762adf5ec8a86a00c16544670cb2f998055bd35 Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84877 Reviewed-by: Jayvik Desai <jayvik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Pranava Y N <pranavayn@google.com> Reviewed-by: Eric Lai <ericllai@google.com>
2024-10-28mb/google/fatcat: Remove redundant iGPU device entrySubrata Banik
The iGPU device is enabled by default in the Pantherlake chipset configuration. Remove the redundant device entry in the Fatcat devicetree. This change ensures that the iGPU remains enabled without explicit configuration in the board-specific devicetree. TEST=Able to build google/fatcat and able to see firmware and OS display/UI. Change-Id: I9a2ec9b47acb389f5bb6b30e61352aaefa327328 Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84876 Reviewed-by: Jayvik Desai <jayvik@google.com> Reviewed-by: Pranava Y N <pranavayn@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2024-10-28mb/google/rauru: Add PCIe domain supportJianjun Wang
Add PCIe domain support. TEST=Build pass, show pcie init pass log: mtk_pcie_domain_enable: PCIe link up success (1) BUG=b:317009620 Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com> Change-Id: I3e06dfaf79924cd5352348afaa526fc7dedbb540 Reviewed-on: https://review.coreboot.org/c/coreboot/+/84700 Reviewed-by: Yidi Lin <yidilin@google.com> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-28mb/google/rauru: Add mainboard_needs_pcie_initJianjun Wang
Add a trivial mainboard_needs_pcie_init implementation that always return true. For now, the storage types of rauru SKUs are still unknown. TEST=Build pass, show pcie init pass log: mtk_pcie_domain_enable: PCIe link up success (1) BUG=b:317009620 Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com> Change-Id: I6b4f08e15f62da18aa37226075894f2827a9e7ba Reviewed-on: https://review.coreboot.org/c/coreboot/+/84697 Reviewed-by: Yidi Lin <yidilin@google.com> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-26mb/google/fatcat: Drop LOCK_CONFIG for GPP_D15 in early GPIO configSubrata Banik
Ideally lock configuration is not applicable for early GPIO configuration (like bootblock/romstage) and is only required for GPIO PAD configuration by later statge (like ramstage). The GPP_D15 pin was previously configured with LOCK_CONFIG in the early bootblock GPIO configuration. This is not necessary and prevents later boot stages from configuring this GPIO. Change-Id: Ie0e648b750d7579def39ed95eab862dc3245499c Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84867 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Pranava Y N <pranavayn@google.com> Reviewed-by: Cliff Huang <cliff.huang@intel.com>
2024-10-25mb/google/brox/lotso: Enable BT audio offload configWentao Qin
Enable BT audio offload of WIFI_CNVI_WIFI6E or unprovisioned based on fw_config. BUG=b:373510270 TEST=Build and boot to Lotso. Verify the config from serial logs. w/o this CL - ``` [SPEW ] -- CNVi Config -- [SPEW ] CNVi Mode= 1 [SPEW ] Wi-Fi Core= 1 [SPEW ] BT Core= 1 [SPEW ] BT Audio Offload= 0 ``` w/ this CL - ``` [SPEW ] -- CNVi Config -- [SPEW ] CNVi Mode= 1 [SPEW ] Wi-Fi Core= 1 [SPEW ] BT Core= 1 [SPEW ] BT Audio Offload= 1 ``` Signed-off-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com> Change-Id: I36f8c3fb24166c86d5fc4099fa9cde8cdecb9d49 Reviewed-on: https://review.coreboot.org/c/coreboot/+/84768 Reviewed-by: Bob Moragues <moragues@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jian Tong <tongjian@huaqin.corp-partner.google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2024-10-24mb/google/fatcat: add GPIO pad configure based on fw_configJeremy Compostella
BUG=b:348678529 TEST=on Google Fatcat board. Set the proper CBI fw_config bit(s) and check that the corresponding GPIO PADs are configured as expected value accordingly. Change-Id: I914f73ff06bfb801fc319b45b23d7ce4cb7a6d54 Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84408 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aamir Bohra <aamirbohra@google.com> Reviewed-by: Pranava Y N <pranavayn@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-10-24mb/google/fatcat: Ensure RW_SECTION_B starts at 16MB boundarySubrata Banik
This patch updates the flash map layout to guarantee that the RW_SECTION_B section starts at a 16MB boundary. TEST=Successfully builds google/fatcat. Change-Id: I74ea21a8a4107d438bc03a0da182ea7e991e74bc Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84821 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Pranava Y N <pranavayn@google.com>
2024-10-24mb/google/brya/var/nova: Disable Thunderbolt deviceKenneth Chan
Nova doesn't support thunderbolt, so disable the TBT setting. Enabling TBT also causes the system to fail to enter S3/S5 state. S5 fail log: 24-10-21 20:23:34.610 Port 80 writes: 24-10-21 20:23:34.610 9a02 9a32 9a14 9c15 9c18 9c19 9c20 9c22 9c25 9c28 9c3f 9c43 9c44 9c4f 9c23 9a50 9a5f 9a33 9b40 9b41 24-10-21 20:23:34.620 9b42 9b47 9c80 9c81 9c82 9c83 9a61 9a63 9a03 9a04 9a05 9a06 9a07 9a0f 9a65 9a64 9c6a 9c71 9c7f 99 24-10-21 20:23:34.626 a0 a1 72 24 25 24 25 55 24 25 55 55 73 74 75 75 75 75 75 75 24-10-21 20:23:34.633 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 24-10-21 20:23:34.639 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 24-10-21 20:23:34.643 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 76 77 79 9c 24-10-21 20:23:34.649 93 7a fe 7b f8 aa ab 96 <--new powerinfo 24-10-21 20:23:59.424 powerinfo 24-10-21 20:23:59.424 power state 4 = S0, in 0x00ff The correct power state for S5 is G3, not S0. BUG=b:374213121 TEST=emerge-constitution coreboot chromeos-bootimage. Booting to OS and verify S3/S5 by EC log. Change-Id: I2bae8ae396f001dbef3322e361f9563792e1a1ef Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84838 Reviewed-by: Pranava Y N <pranavayn@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-10-24mb/google/nissa/var/glassway: Add touch screen ELAN9004 supportDaniel Peng
1. 2nd touch panel: INX N140HCN-EA1 C5 2. Set TOUCHSCREEN_ELAN9004 to value "3" BUG=b:374899470 BRANCH=firmware-nissa-15217.B TEST=1. emerge-nissa coreboot chromeos-bootimage 2. Confirm command evtest and touchscreen function is workable. Change-Id: Ic25bd46c7cb7948e920de4fd44edb87f20cf01c4 Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84834 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jayvik Desai <jayvik@google.com>
2024-10-24mb/google/nissa/var/glassway: Support Samsung K3LKBKB0BM-MGCPDaniel Peng
Add the new memory support: Samsung K3LKBKB0BM-MGCP BUG=b:374880584 BRANCH=firmware-nissa-15217.B TEST=Run command "go run ./util/spd_tools/src/part_id_gen/\ part_id_gen.go ADL lp5 \ src/mainboard/google/brya/variants/glassway/memory/ \ src/mainboard/google/brya/variants/glassway/memory/\ mem_parts_used.txt" Change-Id: I47d9fd64fa841a2cf60930c5e319a9130019b0a5 Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84831 Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jayvik Desai <jayvik@google.com>
2024-10-23mb/erying: Add Erying Polestar G613 Pro (TGL-H)Alicja Michalska
Erying is a Chinese manufacturer selling desktop motherboards with laptop SoCs and custom shim to mount desktop coolers. Working: - Serial port (IT8613E 0x3f8) - All rear USB ports (3.0, 2.0) - Both HDMI ports - Realtek GbE NIC - Internal audio (ALC897/ TGL-H HDMI) - Environment Controller (SuperIO fan control) - All SATA ports - All PCI-E/M.2 ports - M.2 NGFF WiFi - PCI-E Resizable BAR (ReBAR) - VT-x WIP/Broken: - PCI-E ASPM (also broken on vendor's FW, clocks are messed up) - S3/s0ix (also broken on stock, setting 3VSB register didn't help - system goes to sleep, but RAM loses power) - DisplayPort on I/O panel (seemingly a simple fix) - One of USB2 FP connectors, as well as NGFF USB isn't mapped (yet) - Automatic fan control (IT8613E can't read CPU_TIN at the moment) Can be flashed using `flashrom -p internal -w build/coreboot.rom`, as vendor hasn't enabled any protections on SPI chip. TEST=Flash coreboot build onto the motherboard, install following PCI-E cards: Radeon RX 7800XT, Kingston KC3000, Optane 900P, Audigy X-Fi. Power the system up and boot into Windows 10 to check ACPI sanity, then reboot into Fedora Linux (kernel 6.10.9) and launch 3D application, disk benchmark, compilation at the same time to check system's stability. Change-Id: Iffb9e357da2eb686bdcd9a9837df8a60fa94011e Signed-off-by: Alicja Michalska <ahplka19@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80853 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2024-10-23device/pciexp: Add hot-plug capable helper functionPatrick Rudolph
Add and use a new helper function to determine if a device is 1) a PCIe device 2) it's mark hot-plug capable Change-Id: I61cc013844024b43808cd2f054310cb6676ba69e Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84792 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shuo Liu <shuo.liu@intel.com>
2024-10-23mb/ocp/deltalake: Clean codePatrick Rudolph
Use dev_find_all_devices_on_stack() to find the PCI device on a given stack. That way open coded duplicated code can be dropped and there's no need to call socket0_get_ubox_busno(), which allows to drop socket0_get_ubox_busno(). In addition it adds PCI multi segment support. Change-Id: Ib0ed177ae22112a9f2ed32199409d91cb5851ede Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84790 Reviewed-by: Alicja Michalska <ahplka19@gmail.com> Reviewed-by: Shuo Liu <shuo.liu@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-21mb/google/fatcat: Disable C1 state auto-demotion for ES SoCJamie Ryu
This disables C1 state auto-demotion to run the coreboot with Panther Lake ES SoC without an issue. This configuration will be remove later once the related features are fully verified. BUG=b:373915085 TEST=Build fatcat and check the platform boots without an issue. Change-Id: I384dba2918cfd04deb90284513c204fa8c21094b Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84767 Reviewed-by: Dinesh Gehlot <digehlot@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Jayvik Desai <jayvik@google.com>
2024-10-21mb/google/brox/jubilant: Modify WWAN Rolling RW101R-GL power sequenceRen Kuo
There is no ACPI power resource for LTE module Rolling RW101R-GL, therefore implement the power sequence of power-on, power-off, and reset timing from GPIO init, bootstate init callbacks, and smihandler function. BUG=b:368450447 BRANCH=None TEST= Build firmware and verify on jubilant with LTE:RW101R-GL. Measure the power on, power off, and reset timing. Run warm boot, cold boot and suspend/resume to make sure WWAN devcie is workable. Change-Id: I4a205e3db777c7c225d31b6cc802883fd7167089 Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84689 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2024-10-21mb/google/brox/jubilant: Update CPU power limitsRen Kuo
Update jubilant CPU PL4 from 9 watt to 14 watt for critical battery boot. The maximum peak power is set at 14 watt which is 45W multiplied by 32% efficiency. Overriding power limits for AC power without battery: PL1 (15000, 18000) PL2 (41000, 41000) PL4 (14) BUG=b:364441688 BRANCH=None TEST=Able to successfully boot on jubilant SKU1 and SKU2 with AC only. Test on AC 65W and 45W w/o battery, and check PL4 values from log. Change-Id: Id1e58797206a61d241f48b057b304e05c9c323d9 Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84784 Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Sowmya Aralguppe <sowmya.aralguppe@intel.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-21mb/google/dedede/var/drawcia: Add Realtek WLAN card supportRobert Chen
Add wifi PCIe hosts M.2 E-key WLAN to fulfill drawman_jsl_schematic_20200528. BUG=None BRANCH=firmware-dedede-13606.B TEST=emerge-dedede coreboot chromeos-bootimage Change-Id: If414ff1941d2d70c5f0444ac58b228ed5c95303a Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84612 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Derek Huang <derekhuang@google.com>
2024-10-19mb/google/rauru: Add new board variant NaviLeo Chou
Add a new Rauru follower 'Navi'. BUG=b:341210522 TEST=emerge-cherry coreboot Change-Id: Ia2a6c1c09b3cedc0ef7f51ec93fdabf2c07c8885 Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84694 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Reviewed-by: Yidi Lin <yidilin@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-19mb/google/rauru: Add NAU8318 supportAmanda Huang
NAU8318 supports beep function via GPIO control. Configure the GPIO pins and pass them to the payload. BUG=b:343143718 TEST=Verify beep function through CLI in depthcharge successfully. We can test with: firmware-shell: badusbbeep firmware-shell: devbeep Change-Id: I79277bc1947dab517dea5aba583c5b4e0ac81bc4 Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84693 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Reviewed-by: Yidi Lin <yidilin@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-19mb/google/rauru: Configure the fingerprint pinsYidi Lin
There is no powering-on control in the fingerprint kernel driver. The fingerprint team of ChromeOS suggests powering-on FP MCU in the FW. Follow trogdor to pull down FP_RST_1V8_S3_L, AP_FP_FW_UP_STRAP, EN_PWR_FP and pull up EN_PWR_FP in ramstage for power rail to be stable. BUG=b:340401582 TEST=measure waveform and the fingerprint works on ChromeOS Change-Id: I05600d90fdf922faeb778a36d8a08f68c1bb4125 Signed-off-by: Yidi Lin <yidilin@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84692 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yidi Lin <yidilin@google.com>
2024-10-19mb/google/rauru: Pass XHCI_INIT_DONE to the payloadYidi Lin
Configure GPIO EINT28 (XHCI_INIT_DONE) as output, so that payloads (for example depthcharge) can assert it to notify EC to enable USB VBUS. BUG=b:317009620 TEST=emerge-rauru coreboot Change-Id: I5950974435b56997626886b16d371cd8e6472e3c Signed-off-by: Yidi Lin <yidilin@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84691 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yidi Lin <yidilin@google.com>
2024-10-17mb/google/nissa/var/glassway: Add convertible and clamshell WIFI SAR ↵Daniel Peng
FW_CONFIG ids Based on Gallida360 design, we add two new options for WIFI_SAR_ID: - WIFI_SAR_ID_INTEL_CONVERTIBLE 2 - WIFI_SAR_ID_INTEL_CLAMSHELL 3 BUG=b:372354703 BRANCH=firmware-nissa-15217.B TEST=emerge-nissa coreboot chromeos-bootimage Change-Id: I1b58c4f572d4dbcb269d38485664ddc51e378e5e Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84779 Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jayvik Desai <jayvik@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-10-17mb/google/fatcat: Create francka variantIan Feng
Create the francka variant of the fatcat reference board. BUG=b:370666276 TEST=util/abuild/abuild -p none -t google/fatcat -x -a make sure the build includes GOOGLE_FRANCKA Change-Id: I372f445f7007d0d33020545a8febbce27c260e41 Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84769 Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com> Reviewed-by: Amanda Hwang <amanda_hwang@compal.corp-partner.google.com> Reviewed-by: Pranava Y N <pranavayn@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-17mb/google/fatcat: add pre-mem configuration based on fw_configCliff Huang
Add the GPIO pad configuration to be performed before memory is set up along with the relevant devices definition. This patch includes: - FW config for pre-mem GPIO PAD configuration - Add overridetree changes used by pre-mem FW config BUG=b:348678529 TEST=Boot on Google Fatcat board. Note this cannot be tested by itself directly. Test with CL:84408, set the proper CBI fw_config bit(s) and check that the corresponding GPIO PADs are configured as expected value accordingly. Signed-off-by: Cliff Huang <cliff.huang@intel.com> Change-Id: Iac1f637c21a9818512b224dc4cbe4a75dbc516ce Reviewed-on: https://review.coreboot.org/c/coreboot/+/84718 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Pranava Y N <pranavayn@google.com>
2024-10-16mb/google/brya: Create telith variantKun Liu
Create the telith variant of the nissa reference board by copying the template files to a new directory named for the variant. (Auto-Generated by create_coreboot_variant.sh version 4.5.0) BUG=372506691 BRANCH=None TEST=util/abuild/abuild -p none -t google/brya -x -a make sure the build includes GOOGLE_TELITH Change-Id: I4971b9691d3dd293ca640795967c36472afef9c9 Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84759 Reviewed-by: Dinesh Gehlot <digehlot@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jian Tong <tongjian@huaqin.corp-partner.google.com> Reviewed-by: Eric Lai <ericllai@google.com>
2024-10-16mb/arm/rdn2: Add support for Arm Neoverse N2Naresh Solanki
Add support for Arm Neoverse N2 Reference design. Based on Arm Neoverse N2 reference design Revision: Release D TEST=Build Arm Neoverse N2 & make sure there is no error. Change-Id: I17908d3ce773d4a88924bafb1d0e9e2a043c7fbc Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79103 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com> Reviewed-by: Julius Werner <jwerner@chromium.org>
2024-10-16mb/ibm/sbp1: Add SMBIOS slotsPatrick Rudolph
Add the BMC and all PCIe slots that the board implements. There are 32 RSSDs and 2 M.2 slots. Change-Id: Id7d72990d6997d1e8b9ce75477ce3dc571c99839 Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84560 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2024-10-16mb/google/brya/var/glassway: Add Stylus FunctionDaniel Peng
1. Add STYLUS fw_config setting. 2. Enable stylus device settings. 3. Disable the stylus GPIO pins based on fw_config. BUG=b:364798563 BRANCH=firmware-nissa-15217.B TEST=1. emerge-nissa coreboot 2. Confirm command evtest for stylus PRP0001:00 and workable. Change-Id: Ifa8555eed1c31e9342a50a735fc618106f26d41a Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84713 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
2024-10-14i945: Use nullptr instead of NULLElyes Haouas
nullptr was introduced in C11 spec and gcc 4.7. https://en.cppreference.com/w/cpp/language/nullptr https://stackoverflow.com/questions/16256586/how-to-enable-c11-on-later-versions-of-gcc coreboot switched to GCC 4.7.2 on October 25, 2021, prior to coreboot v4.1. https://review.coreboot.org/c/coreboot/+/1609 GCC-13 implemented nullptr constant: https://www.open-std.org/jtc1/sc22/wg14/www/docs/n3042.htm So use it insted of NULL macro. Change-Id: I7d47e692a33d739345a81f589d4329a31beeb8c5 Signed-off-by: Elyes Haouas <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83860 Reviewed-by: Martin L Roth <gaumless@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-14drivers/pc80/tpm: Remove flag TPM_RDRESP_NEED_DELAYBill XIE
After CB:76315, TPM_RDRESP_NEED_DELAY, whose historical mission has ended, could be removed. Signed-off-by: Bill XIE <persmule@hardenedlinux.org> Change-Id: I51e046fb738d2ff7a23225739de62a1a7780bc1c Reviewed-on: https://review.coreboot.org/c/coreboot/+/84717 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Crawford <tcrawford@system76.com>
2024-10-14mb/google/nissa/var/sundance: Change touch panel and wwan gpio settingRoger Wang
In order to fit the specification, change gpio setting for touch panel and wwan. Change items: 1. wwan : Add WWAN_RST_L to 0. And we want WWAN_EN to pull high more early than WWAN_RST_L, so add WWAN_EN to 1 in romstage stage. 2. touch panel : First we add EN_PP3300_TCHSCR and USI_RST_L to 0 to init status. And we want EN_PP3300_TCHSCR to pull high more early than USI_RST_L so delete USI_RST_L pull high in romstage. BUG=b:357764679 Test=emerge-nissa coreboot Change-Id: I0a07ea8e2bf3d165dcebd89c4c564f157d9d4846 Signed-off-by: Roger Wang <roger2.wang@lcfc.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84668 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-13mb/google/brox/var/lotso: Reduce gspi speed from 10 MHz to 9 MHzKun Liu
Reduce gspi speed from 10 MHz to 9 MHz, because Raptor Lake Refresh platform GSPI supports max frequency 9 MHz. BUG=b:342932183 TEST=emerge-brox coreboot Change-Id: If5b7885d95cfe21ec71cc37e6d72419935b0844f Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84708 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Jian Tong <tongjian@huaqin.corp-partner.google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-12mb/google/brox/lotso: Enable devices on unprovisioned fw_configWentao Qin
Setting devices to unprovisioned allows us to perform functional testing without having to rewrite the fw config during the SMT phase of factory production. BUG=None TEST=Build lotso firmware and boot to OS when fw_config is unprovisioned and ensure all devices are enable. Change-Id: I3b8285ce335ee0f3595d184eb0921f697bdbd0c2 Signed-off-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84714 Reviewed-by: Jian Tong <tongjian@huaqin.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2024-10-11mb/starlabs/*: Rework the performance profilesSean Rhodes
Rather than hardcoded values, simply change these to -25% of the defaults for Power Saving, and +25% for Performance. Change-Id: I16aeb4d5dc25a3f240a775509276c9d3189e9699 Signed-off-by: Sean Rhodes <sean@starlabs.systems> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84661 Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-11mb/starlabs/*: Adjust the scope of PTTSean Rhodes
The Windows driver only checks PCI0, so move the window accordingly so that it can be used. Tested on `starlite_adl` by booting Windows 11 installation medium. Prior to this patch, it would flag that the security requirements were not met - it now happily installs. Change-Id: I5d0d062502af99104690f9a9affec09f42b5bc71 Signed-off-by: Sean Rhodes <sean@starlabs.systems> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84663 Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
2024-10-11mb/starlabs/byte_adl: Configure GPP_E14 as EDP_HPDSean Rhodes
This pin is used by the DisplayPort connector for Hot Plug. Change-Id: I3c63e2e3e168a915daee81afd6a9084a3f01b986 Signed-off-by: Sean Rhodes <sean@starlabs.systems> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84662 Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-11mb/starlabs/*: Set PL4 to 1.0C of the batterySean Rhodes
Override the PL4 to the maximum power the battery can provide without a charger connected to prevent drawing too much power. Change-Id: I2945e1ed0f33ab6692631e327c1457980b353c06 Signed-off-by: Sean Rhodes <sean@starlabs.systems> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84660 Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-11mb/starlabs/starlite_adl: Correct the SOC definition in devtreeSean Rhodes
The wrong definition was used, so the code had no effect. The ID for the processor used is `b06e0`. Change-Id: I36e13074a77b93871c1d86664e35a33afe39a402 Signed-off-by: Sean Rhodes <sean@starlabs.systems> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84659 Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-11mb/starlabs/*: Enhance USB configuration and commentsSean Rhodes
Some boards use hubs for devices, so correct the ACPI configuration for these ports. Also, add more information to the comments for the ports. Change-Id: I8472130aba8e777557cf68280fa0058dbeb77df9 Signed-off-by: Sean Rhodes <sean@starlabs.systems> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84650 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
2024-10-11mb/starlabs/*: Add PLD Groups to USB ACPI configurationSean Rhodes
Change-Id: I6fb228bab06b050ac1a51de46ffe5c0d3d80adfb Signed-off-by: Sean Rhodes <sean@starlabs.systems> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84649 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
2024-10-11mb/starlabs/starlite_adl: Make I2C speed configurableSean Rhodes
Make the I2C speed user configurable from CMOS. Both the touchscreen and accelerometer support running at 100MHz or 400MHz. They perform better at 400MHz but use more power - this patch lets the user choose. Change-Id: Ia1b08d7ec6212418bb95d0a52077f01c930f8830 Signed-off-by: Sean Rhodes <sean@starlabs.systems> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83882 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
2024-10-11mb/starlabs/starlite_adl: Alphabetize and group FSP UPDsSean Rhodes
Change-Id: Ibe47f242ce12fc4906baeee89393a34a56eaca76 Signed-off-by: Sean Rhodes <sean@starlabs.systems> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83881 Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-10mb/starlabs/*: Disable c6dramSean Rhodes
None of these boards support or use S0ix so c6dram isn't needed, so disable it. Change-Id: I8124899a1f7ce20442f28919f7315ee7e52355e5 Signed-off-by: Sean Rhodes <sean@starlabs.systems> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84632 Reviewed-by: Maxim <max.senia.poliak@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-10mb/starlabs/byte_adl/mk_ii: Correct USB Port Names to Type-ASean Rhodes
There is only 1 Type-C port, the rest are Type-A. Tested on Linux by verified the correct names are shown in dmesg. Change-Id: Iaf5a29f3d25f299658116fa61ae488775e2b70a2 Signed-off-by: Sean Rhodes <sean@starlabs.systems> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84642 Reviewed-by: Maxim <max.senia.poliak@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-10-10mb/starlabs/starlite_adl: Adjust the configuration for USB 2 Port 2Sean Rhodes
Port 2 is a hub, used for the internal keyboard and the card reader. Adjust this to a hub. Change-Id: I3a9b9e6803934291b46fb502ff1b3b088c047703 Signed-off-by: Sean Rhodes <sean@starlabs.systems> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84641 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Maxim <max.senia.poliak@gmail.com>
2024-10-10mb/starlabs/starlite_adl: Add PLD groups to USB ACPI configurationSean Rhodes
Change-Id: I8ea01c21ec03c11e9599684dbe51d103c07c172a Signed-off-by: Sean Rhodes <sean@starlabs.systems> Reviewed-on: https://review.coreboot.org/c/coreboot/+/84640 Reviewed-by: Maxim <max.senia.poliak@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-27 14:43:55 +0000