| Age | Commit message (Collapse) | Author |
|---|
|
For each sandybridge boards with option to use MRC or native platform
init code, add a copy of the board's USB port config, consolidated between
both code paths, into the southbridge devicetree, using special values
allocated for this consolidation.
These get hooked up in a separate patch.
Change-Id: I53efca3d29b3c5d4d5b7e3d6dc3e6ce6c34201e6
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81880
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This map is found stored in plain text in vendor firmware image.
They will take effect when USB config is transitioned to southbridge
devicetree.
Change-Id: Iab0a225560856771407bb815ff4d8bc95d0f884f
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
For mainboards using southbridge/intel/bd82x6x, copy the contents
of mainboard_usb_ports array into southbridge devicetree. In-line
comments are maintained.
Boards also capable of using MRC raminit are done in a separate
patch.
Change-Id: Ia8a967eb3466106f3a34e024260e13d02f449a25
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81879
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add wifi sar table support for xol. Bit 31 in CBI/FW_CONFIG
is used to select different sar table (index 0 or 1) but only
0 is in used at the moment.
BUG=b:344274789
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
Change-Id: Id4dc74c4f2a807d2e531b419ecb7b590d4c32ac2
Signed-off-by: YH Lin <yueherngl@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Current existing temperature thresholds of TSR1 sensor are set at 60C
to start fan. Due to this CPU gets hot and temperature goes over 80C.
In this situation, fan does not even start to lower down CPU temperature.
With updated new settings based on tuning from thermal team, start fan
early at 40C for TSR0 and TSR1 so the CPU temperature stays below 80C.
BUG=b:339493551
TEST=Built and tested on google/brox board
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Change-Id: I4765c13c10e436733d8c9d017085968daa561ccc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82784
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Change-Id: If43089560a391d6a844ef1716b277e3146c66945
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This change restores the EN_PP3300_SSD GPIO configuration in the
ramstage for the Rex0 variant. This is necessary to enable testing
of RO lockdown scenarios on FSI'ed Screbo devices, where bootblock
changes are not applicable.
Additionally, ensures locking the GPIO PAD from getting misconfigured
after booting to OS.
BUG=b/337971452
BRANCH=firmware-rex-15709.B
TEST=Able to boot google/rex with RO locked to an older version without
SSD GPIO refactored, and RW is with the latest revision.
Change-Id: Ia7564b14a20d00e9bb2c9466b7a737dd97f01351
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Add AX211 and AX203 wifi sar table for pujjoga wifi sar config.
Use fw_config to separate different wifi card settings.
WIFI_SAR_TABLE_AX211: 0
WIFI_SAR_TABLE_AX203: 1
BUG=b:336167281
Test=emerge-nissa coreboot
Change-Id: If0f542cb13e93e99960bf65d616b26cee7617a43
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add FW_CONFIG probe based on pujjoga boxster of below devices:
WWAN
Schematic version: 500E_GEN4S_ADL_N_MB_0418
BUG=b:336167281
TEST=Boot to OS and verify the WWAN devices is set based on
fw_config.
Change-Id: I94cb9ffe47888a8b7b5c6837ddfc390a1d2e77d1
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add bookem new supported memory parts in mem_parts_used.txt.
Generate SPD id for this part.
Zilia SDVB8D8A34XGCL3N3T
BUG=b:344482259
TEST=Use part_id_gen to generate related settings
Change-Id: I1cbf641e2bbe4fd4eea02a1bfa3d6b3c06e567e4
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82783
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Enable type-c port 0 USB2 function.
BUG=b:327549688
TEST= USE="-project_all project_bujia" emerge-brask coreboot
Change-Id: I0d7adc329a8c26941957d7a7472a5166b07bda5b
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82903
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Kconfig strings for the battery:
* Model
* OEM
* Technology
Change-Id: Ibbce87ad54874f490af45c41f31956a7e9e996f3
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81401
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These values were configured based on a default value of 110, but for
CML, it's actually 100.
Adjust it accordingly.
Change-Id: Ibffeeab67a7277625db9bdedca36d759ff0e72f6
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81414
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the TCC Offset based on the active power profile
Change-Id: I58940441a7cefc7a2a07e5e9f7e8a15cb8730ef3
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
All other variants use a function and definitions to get the power
profile. Make this board to the same.
Change-Id: I07ce71e20bd71229bb0cd3438ab59140cd0d8b42
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81412
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I27062c38c10df1d03f563b2f5391f79a3b6ee4fe
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81411
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It is now possible to hook up device ops directly to devices in
devicetree which removes the need for a fake chip.
This also fixes Hermes booting as the PCI ops were incorrectly hooked up
to a dummy device. The intel uart driver was requesting a resource from
the generic device and died since it does not exist:
[EMERG] GENERIC: 0.0 missing resource: 10
This was broken in commit b9165199c32a (mb/prodrive/hermes: Rework UART
devicetree entry).
Change-Id: I3b32d1cc52afaed2a321eea5815f2957fe730f79
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82940
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Replace `0x411111f0` with `AZALIA_PIN_CFG_NC(0)`, which evaluates to the
same value and conveys additional information to the reader. Done with a
bulk search and replace operation.
Change-Id: Ibd84daec017bc1ab1ee4edd906fda80231c134cc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82394
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Currently, the 3rdparty/fsp submodule contains only the IoT FSP for
ADL-N. However, coreboot's Kconfig is incorrectly applying the IoT
FSP for both Client and IoT configurations, despite the Client FSP
requiring distinct headers.
The CWWK CW-ADL-4L-V1.0 board relies on the FSP provided by the
3rdparty/fsp submodule, which means it has been using the IoT FSP by
default. To ensure the board continues to use the correct FSP as we
plan to introduce Client FSP headers into vendorcode, we are now
explicitly select FSP_TYPE_IOT for the CWWK CW-ADL-4L-V1.0 board.
Change-Id: Ie3844cb24740e4d95ee835a44e55b4d5cb6854e5
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82915
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Brandon Weeks <bweeks@google.com>
|
|
Currently, the 3rdparty/fsp submodule contains only the IoT FSP for
ADL-N. However, coreboot's Kconfig is incorrectly applying the IoT
FSP for both Client and IoT configurations, despite the Client FSP
requiring distinct headers.
The aoostar/wtr_r1 board relies on the FSP provided by the 3rdparty/fsp
submodule, which means it has been using the IoT FSP by default. To
ensure the board continues to use the correct FSP as we plan to
introduce Client FSP headers into vendorcode, we are now explicitly
select FSP_TYPE_IOT for the aoostar/wtr_r1 board.
Change-Id: I68feeaaffd825013ae1012694047b067535e7341
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82914
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove the entries which have the same state as the ones from the
chipset devicetree.
Change-Id: I4981cd835ef28a673d480808dd486fed4d9b45e5
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Based on lotso EVT schematics add dq map settings.
BUG=b:333494257
TEST=emerge-brox coreboot chromeos-bootimage and boot on
Change-Id: I4f03e8a90522cbf2fe06f4160414202dcc4a2199
Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82600
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Dengwu Yu <yudengwu@huaqin.corp-partner.google.com>
|
|
This was done using Haswell autoport, with manual fixes to get the
output to build against current main. I do not physically have this
board; I was sent the output of autoport with some fixes on top of
which I added additional changes. The VBT was copied from
/sys/kernel/debug/dri/0/i915_vbt on version 2.70 of the vendor firmware.
The flash chip is 8MiB in a socketed DIP8 package, making it easy to
externally flash to recover from a brick.
Working:
- Haswell MRC.bin
- S3 suspend and resume
- Libgfxinit
- HDMI
- DVI-I (including passive DVI to VGA adapter)
- DisplayPort
- SATA ports
- mSATA SSD
- mPCIe WiFi slot
- Rear USB ports
- USB 3.0 header
- Audio header
- Ethernet
- x16 PCIe slot
- EHCI debug with the CH347 (top USB 2.0 port by the PS/2 connector)
- edk2 (MrChromebox uefipayload_202309)
Not Tested:
- PS/2 keyboard/mouse
- eSATA
- USB 2.0 header
Change-Id: I56c22d8f5505f9a4da25f8b4406b00978af1a586
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81022
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I98aa3f582963f76690f907b678ac322ed4cc99d1
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82846
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I972516443bc57e193aefd54516ca994087d92054
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Based on lotso EVT schematics update gpio settings.
BUG=b:333494257
TEST=emerge-brox coreboot chromeos-bootimage and boot on
Change-Id: I13485cc7ccd8b15352f5e21ad9336aa2b3d35749
Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82573
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Based on schematic, update slot number for PCIe port used for NIC
controller.
Change-Id: I7a1ead8f7e4588db45303041e60dbfe27ee12ea7
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
There's two copies of the `get_cxl_mode()` function to map the OCP VPD
value to the values expected by platform code. As this is unnecessary,
have a single copy of this function in the OCP VPD driver code. As the
`get_cxl_mode()` function is Xeon-SP only, keep it in a separate file.
This change simplifies things for boards using OCP VPD for CXL and has
no impact for boards *not* using OCP VPD:
- Boards not using OCP VPD can still define get_cxl_mode() in mainboard
code as needed, just like they were able to do before.
- Boards using OCP VPD but without CXL (`SOC_INTEL_HAS_CXL` is not
enabled), this code won't get compiled in at all (see `Makefile.mk`).
- Boards using OCP VPD and CXL will automatically make use of this
`get_cxl_mode()` definition, which should be the same for all boards.
It is possible that this may need to be expanded/adapted in the future,
which is easy to handle in a follow-up commit when the need arises.
TEST=Build and boot on intel/archercity CRB
Change-Id: I935c4eb5b2392e2d0dc01b9f66d46c79b8141ea7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82224
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Set GSC_SOC_INT_ODL to GPP_A17 instead of GPP_A13.
BUG=b:333486830
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I065fdf2a66036c6df1e16dda3b2a684b5202cccc
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82717
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ib8f7ac7e586390a1d25cbe84d6d4c3ba31ff078f
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Set LpDdrDqDqsReTraining to 1 for xol. Value 0 will cause black screen
issue.
Reference: https://review.coreboot.org/c/coreboot/+/79527
> FSP default value for LpDdrDqDqsReTraining is 1. For boards
> that didn't set LpDdrDqDqsReTraining to any value, 0 was being
> assigned and it caused black screen issue.
BUG=b:332980211
BRANCH=brya
TEST=Built and verified there is no black screen issue during power
on/off test for over 100 cycles.
Change-Id: Ia346ce559b4509ea1a63abe28b12ad909f9b7b0d
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82778
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Due to system spec change, change audio codec ALC5650 to ALC5682I-VS
BUG=b:329787697
TEST= USE="-project_all project_bujia" emerge-brask coreboot
Change-Id: I38e5c58b3ef3fbe709b98601975ae3821bb77213
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
The Razer Blade Stealth Kaby Lake has 2 variants. One is the H2U
variant, as originally committed, with the SKU number RZ09-01962, also
known as the 2016 model, and the H3Q model with SKU numbers RZ09-01963
and RZ09-01964, known as the Mid 2017 model. This commit adds support
for the H3Q model. With respect to coreboot, there are few known
differences:
1. Only the H2U has TPM.
2. The USB ports are different.
3. The screen size (and therefore VBIOS Table) is different.
4. The hda_verb is very slightly different.
5. The gpio is different.
Change-Id: I493a651e52c2eb938daa67a05e9caaa784020fa4
Signed-off-by: Reagan Bohan <xbjfk.github@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I1ed280c1e62e0f094fd40d2165892240f76de390
Fixes: 29f1b791270b ("mb/system76/rpl: Add Adder WS 4 as a variant")
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Ensure per-board smart amp init is configured. Fixes speaker output on
oryp12.
Change-Id: I40ff1889dd144bf83ef85979a55535493aa7abdd
Fixes: 8b9716e2269d ("mb/system76/rpl: Add Oryx Pro 12 as a variant")
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
Change-Id: I55f2730f7277a3c699b86ded5864e9690d92d518
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82700
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Add Rex64 board to Kconfig menu
- Enable building for Rex64 with x86_64 support
Change-Id: I02e2c49b4aeb2cb98d9d0cb66717db18c3f96d45
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82625
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Update used USB port[2][3](type-a) setting for nova.
BUG=b:328711879
TEST=emerge-constitution coreboot chromeos-bootimage
Change-Id: I63cf97b23627feac05743f2a6e514a33fcaf7dff
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82703
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
The devicetree entry and gpio.c updated as per the schematics of Trulo
to map the OC fault signals from A0/A1 USB ports.
BUG=b:335858378
TEST= Able to build google/trulo
Change-Id: Ic17debc5eecebca8c000c43a660e1b52d2932f2a
Signed-off-by: Pranava Y N <pranavayn@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82637
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
|
|
<gpio.h> is supposed to chain-include <soc/gpio.h>.
Change-Id: Ib25581bd2c8dd38cdd0396561ce5f9a782365f14
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82691
Reviewed-by: Michał Kopeć <michal.kopec@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since this mainboard no longer uses the FSP GOP driver, the DDI port
settings are no longer necessary. The GOP driver was used in the initial
phase of development where we used Tianocore as payload for some test
cases. Finally, this mainboard uses a self-made Linux payload, which
does the graphic initialization.
BUG=none
TEST=Boot into Linux and check if graphic works correctly
Change-Id: Ie9e135fbc2627546d6ef95d7d5ff3e9a9222b5d2
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82663
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The Adder WS 4 (addw4) is a Raptor Lake-HX board.
Tested with a custom edk2 UefiPayloadPkg.
Working:
- PS/2 keyboard
- I2C HID touchpad
- Both DIMM slots (with Crucial CT8G48C40S5)
- M.2 NVMe SSDs
- All USB ports
- MicroSD card reader
- Webcam
- Ethernet
- WiFi/Bluetooth
- Integrated graphics using Intel GOP driver
- Backlight controls on Linux 6.8
- DisplayPort output over USB-C
- Internal microphone
- Internal speakers
- Combined headset + mic 3.5mm audio
- 3.5mm microphone input
- S3 suspend/resume
- Booting Pop!_OS Linux 22.04 with kernel 6.8.0
- TPM 2.0 device
Not working:
- Discrete/Hybrid graphics
- Detection of devices in TBT slot on boot
Change-Id: I4a6819cbcf64f68237008adebdd7eb196336514c
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82595
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Oryx Pro 12 (oryp12) is a Raptor Lake-HX board.
Tested with a custom edk2 UefiPayloadPkg.
Working:
- PS/2 keyboard
- I2C HID touchpad
- Both DIMM slots (with Crucial CT8G48C40S5)
- M.2 NVMe SSDs
- MicroSD card reader
- Webcam
- Ethernet
- WiFi/Bluetooth
- Integrated graphics using Intel GOP driver
- Backlight controls on Linux 6.8
- Internal microphone
- Internal speakers
- Combined headset + mic 3.5mm audio
- 3.5mm microphone input
- S3 suspend/resume
- Booting Pop!_OS Linux 22.04 with kernel 6.8.0
- TPM 2.0 device
Not working:
- Discrete/Hybrid graphics
- Thunderbolt
Change-Id: I11cf2dbd1512ebae44e0109bdb78e6eafa027444
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Some drives block the CPU from reaching C10 during S0ix suspend without
the RTD3 configs.
Fixes suspend with the following drives:
- Kingston KC3000 (SKC3000D/4096G)
- Kingston HyperX (SHPM2280P2H/240G)
- Solidigm P44 Pro (SSDPFKKW010X7)
The following drives continue to work:
- Samsung 970 Evo (MZVLB250HAHQ)
- WD Black SN770 (WDS250G3X0E)
- WD Green SN350 (WDS240G2G0C-00AJM0)
- WD Blue SN570 (WDS100T3B0C)
Change-Id: Ia369727d0f1aa5ff546cfb5700a63063730e8248
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Tested-by: Levi Portenier <levi@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
MKBP device is required for passing events from input sources to AP.
Input sources include buttons (power, volume); switches (lid, tablet
mode) and sysrq.
BUG=b:342227155
TEST=Able to build coreboot for mtlrvp platform and switch tablet
mode.
Change-Id: I630421c83784bb4492486d72290b9e8cdada1d47
Signed-off-by: Jay Patel <jay2.patel@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82612
Reviewed-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
|
|
Sundance support FM101 WWAN, use wwan_power.asl to handle the
power off sequence
BUG=b:343139385
TEST=Build and boot on sundance
Change-Id: I82085172db370ab5a6c0f77afe6042c53b89e43e
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Modify the Goodix touchscreen from new vendor and remove 3 unused
touchscreens. According to the information provided by the key-part
team.
BUG=b:340689681
TEST=Build and check Goodix touchscreen can work.
Change-Id: I1e6349e80431aadf27cd72b8439b01f95348071d
Signed-off-by: Roger Wang <roger2.wang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82427
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Currently Samsung eMMC (KLMBG2JETD-B041) can't power on to OS nomally.
According to Intel provides eMMC DLL delay patch that tuning on each
Sundance different eMMC system to modify some system can't boot to OS problem.
BUG=b:342057438
TEST=Build and check each SKU eMMC can work.
Change-Id: I29d4305bbe5f91d822d947cae942b654e80a8a57
Signed-off-by: Roger Wang <roger2.wang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82602
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Change-Id: I9ed1a82fcd3fc29124ddc406592bd45dc84d4628
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
<stdio.h> header is used for input/output operations (such as printf,
scanf, fopen, etc.). Although some input/output functions can manipulate
strings, they do not need to directly include <string.h> because they
are declared independently.
Change-Id: Ibe2a4ff6f68843a6d99cfdfe182cf2dd922802aa
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82665
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7d7ad562eeff7247b7377b6570d489faee0aeda0
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82669
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Commit 4c7e97b26a34 ("Update fsp submodule to upstream master branch")
included an update to the VBT from 240 to 250, breaking parsing of
existing VBTs.
After that commit, the VBT was parsed as (from gaze16-3060-b):
[DEBUG] PCI: 00:02.0 init
[INFO ] GMA: Found VBT in CBFS
[INFO ] GMA: Found valid VBT in CBFS
[INFO ] framebuffer_info: bytes_per_line: 4096, bits_per_pixel: 32
[INFO ] x_res x y_res: 1024 x 768, size: 3145728 at 0xd0000000
[DEBUG] PCI: 00:02.0 init finished in 6 msecs
When the expected output is:
[DEBUG] PCI: 00:00:02.0 init
[INFO ] GMA: Found VBT in CBFS
[INFO ] GMA: Found valid VBT in CBFS
[INFO ] framebuffer_info: bytes_per_line: 7680, bits_per_pixel: 32
[INFO ] x_res x y_res: 1920 x 1080, size: 8294400 at 0xd0000000
[DEBUG] PCI: 00:00:02.0 init finished in 6 msecs
Generate blobs for the new version using Intel Display Configuration
Tool (DisCon) v3.3, based on the existing 237 and 240 VBTs.
(For our edk2 payload, the UEFI GOP driver was updated to 17.0.1077.)
Tested on all affected systems:
- darp7
- galp5
- gaze16-3050
- gaze16-3060
- gaze16-3060-b
- lemp10
- oryp8
Tested:
- Boot splash displays on screen again
- Firmware setup menu is rendered, at correct resolution
Change-Id: I918356d9f660b985ee4408ef77544fbd071ab35f
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Tested-by: Daniel Sutton <daniel@system76.com>
Tested-by: Jacob Kauffmann <jacob@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Select MAINBOARD_USE_EARLY_LIBGFXINIT for brox to enable SOL image.
This patch enables Sign of Life image during MRC training.
BUG=b:335369811
TEST=Able to boot to ChromeOS with SOL image.
CPU log:
[SPEW ] bootmode is set to: 0 (boot with full config)
[0.384818] DP PHY mode status not complete
[0.388911] DP PHY mode status not complete
[0.393197] DP PHY mode status not complete
[0.397484] DP PHY mode status not complete
[0.401771] DP PHY mode status not complete
[0.406057] DP PHY mode status not complete
[0.410345] DP PHY mode status not complete
[0.414632] DP PHY mode status not complete
[0.418916] DP PHY mode status not complete
[0.423203] DP PHY mode status not complete
[0.427491] DP PHY mode status not complete
[0.431777] DP PHY mode status not complete
[INFO ] Informing user on-display of memory training.
[DEBUG] FMAP: area COREBOOT found @ 1877000 (7901184 bytes)
[WARN ] CBFS: 'preram_locales' not found.
[ERROR] ux_locales_get_text: preram_locales not found.
[DEBUG] FMAP: area RW_ELOG found @ f20000 (16384 bytes)
[INFO ] ELOG: NV offset 0xf20000 size 0x4000
elogtool list:
0 | 2024-05-10 02:26:07-0700 | Log area cleared | 4088
1 | 2024-05-10 02:26:07-0700 | Early Sign of Life | MRC Early SOL Screen Shown
2 | 2024-05-10 02:26:51-0700 | Memory Cache Update | Normal | Success
3 | 2024-05-10 02:27:09-0700 | System boot | 4
4 | 2024-05-10 02:27:09-0700 | Firmware Splash Screen | Enabled
5 | 2024-05-10 02:27:11-0700 | System Reset
6 | 2024-05-10 02:27:11-0700 | Firmware vboot info | boot_mode=Developer | fw_tried=A | fw_try_count=0 | fw_prev_tried=A | fw_prev_result=Unknown
7 | 2024-05-10 02:27:18-0700 | ACPI Enter | S5
8 | 2024-05-10 02:27:36-0700 | System boot | 5
9 | 2024-05-10 02:27:36-0700 | Firmware Splash Screen | Enabled
10 | 2024-05-10 02:27:37-0700 | System Reset
11 | 2024-05-10 02:27:37-0700 | Firmware vboot info | boot_mode=Developer | fw_tried=A | fw_try_count=0 | fw_prev_tried=A | fw_prev_result=Unknown
Change-Id: I1d4795825960bc58f8f7ef494b01aa975f3bc346
Signed-off-by: Sowmya Aralguppe <sowmya.aralguppe@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
|
|
This patch adds initial PCI device entries into the baseboard
devicetree.cb.
TEST=Able to build google/trulo.
Change-Id: I6ec25b98379cf7c8cbdb5be94d9f3ea43878620c
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82652
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This patch marks unused USB ports (USB2.0/TCSS) empty to avoid
prompting wrong dmesg as below.
```
usb usb2-port3: Cannot enable. Maybe the USB cable is bad?
```
Trulo variants to override the USB ports as per the target
board design.
TEST=Able to build google/trulo.
Change-Id: I6240e66ed3d1a7198c1a526fdca2483910157235
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This patch adds chip config entries for EC host cmd and memory map
ranges.
TEST=Able to build Google/Trulo.
Change-Id: Id4b0f3bba934c8da56b6d7ca8579b46b6cccac28
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
AOOSTAR R1 is a Chinese NAS based on Intel N100 (Alder Lake N), with
two 3.5" HDD slots, an M.2 NVMe 2280 SSD slot and a single DDR4-3200
SODIMM slot up to 32GB. It also comes with 2x 2.5Gb Intel NICs,
Intel AX200 WiFi + BT and USB-C Alt-DP Power Delivery.
Working:
- DDR4 RAM (tested with Crucial 16GB 3200MHz CL22)
- Automatic FAN control (IT8613E Super I/O)
- M.2 NVME slot
- 2x SATA ports (Issue on 3.5" HDD, see below)
- USB 2.0 ports
- USB 3.0 ports
- USB-C port with Alt-DP and PD
- HDMI / DisplayPort ports
- 2x 2.5Gb NICs
- WiFi + BT
- MicroSD card reader
- ASPM (Unavailable on stock)
- Linux (Arch Linux, kernel 6.8.7-arch1-1) UEFI booting with EDK2
- Windows 10 UEFI booting with EDK2
Broken:
- Power button (OFF->ON broken, ON->OFF works)
- 3.5" SATA HDDs (Detected only after reboot)
Untested:
- Internal audio
- S3
My motivation for doing this port is enabling ASPM, as it makes a
great difference on idle power consumption (from 8.4W to 5W measured
from the wall).
The last remaining annoyance of this port is the power button not
working. I spent a few hours double checking the Super I/O registers but
then I gave up. A workaround for this is to use the "ON after power
loss" feature and reconnect the power cord to turn on the board.
It's not a big problem for a NAS that will stay ON 24/7.
Any hint on the power button or 3.5" HDD issue is welcome.
VBT extracted from vendor UEFI firmware version 1AXFE 0.01 x64
(Build date and time 11/29/2023 10:57:44)
Compiled with FSP GOP video initialization, using IFD descriptor
and ME blob extracted from vendor UEFI firmware (see above).
The board can be flashed externally using a 1.8V adapter, I used a
CH341a modded for 3.3V I/O. Internal flashing works, as flash is
not read/write protected.
Patchset 5: Re-enabled dptf, added default options to Kconfig.
Patchset 7: Configured USB port mapping and overcurrent, USB3.0 works
Patchset 8: Fixed microSD card reader
Patchset 13: Change Super I/O Fan configuration to reduce fan noise
Change-Id: I9414eb742b6b90459e010b038c1994537e9801a5
Signed-off-by: Federico Amedeo Izzo <federico@izzo.pro>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82010
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust setting as recommended by power team.
Add ramstage.c in Makefile.inc to set psys_pl2_watts in
variant_devtree_update().
Also copy CPU power limit values from ovis baseboard.
BUG=b:320410462
BRANCH=firmware-rex-15709.B
TEST=FSP debug emerge-ovis coreboot intelfsp
check overrides setting
[INFO] CPU PsysPL2 = 178 Watts
[INFO] Overriding PsysPL2 (178)
[INFO] Overriding power limits PL1 (mW) (19000,28000) PL2 (mW)
(64000, 64000) PL4 (W) (120)
Change-Id: I9ce3a8f843a87e81d404778aaf250b876b6801eb
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Adjust settings as recommended by thermal team.
Set PL1 max value tdp_pl1_override from 28W to 33W.
PL2, PL4 remain the same as CPU default.
BUG=b:308704811
BRANCH=firmware-rex-15709.B
TEST=emerge-ovis coreboot chromeos-bootimage
built bootleg and verified test result by thermal team
Change-Id: Iad0bca913496dda666ba9bcfe5f6fce1a6396692
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82615
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust settings as recommended by thermal team.
Set tcc_offset value to 5 in devicetree.
BUG=b:308704811
BRANCH=firmware-rex-15709.B
TEST=emerge-ovis coreboot chromeos-bootimage
built bootleg and verified test result by thermal team
Change-Id: I30f54ae6017c54c91ff9b432bba0ebd5bfc65ab9
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82614
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Adjust settings as recommended by thermal team.
Update DPTF parameters based on b:308704811#comment4.
BUG=b:308704811
BRANCH=firmware-rex-15709.B
TEST=emerge-ovis coreboot chromeos-bootimage
built bootleg and verified test result by thermal team
Change-Id: I710682771bd0679ae4b44dd43be68f60e8984b2e
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
get_cxl_mode() is the interface for CXL mode config check used by
SoC codes. It could be implemented by mechanisms outside of the
SoC codes, e.g. board codes or OCP VPD driver.
Move the interface declaration out of soc/util.h to a dedicated
header, a.k.a., soc/config.h, so that the implementation codes do
not need to include soc/util.h where there are lots of irrelevant
definitions. Future SoC config check interfaces could be added
to soc/config.h as well.
The default weak implementation is moved out of util.c to
config.c as well.
TEST=Build and boot on intel/archercity CRB
Change-Id: Ia0302b0d3fd93c49e1d6f64e8159f59d50f33e20
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82293
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch tries to simplify the baseboard/variant GPIO programming
for Google/Trulo. The idea is to let each variant maintain
its own complete GPIO PAD configuration table instead of having a
back-and-forth call between baseboard and variants.
With this patch coreboot performing GPIO programming is now much
simpler where the common code block calls into respective variants
and gets the gpio table prior to the pad configuration.
BUG=b:334826281 ([TWL] Decouple GPIO from baseboard to variant)
TEST=Able to build google/orisa.
Change-Id: I4ab88ac094a45c608cd894feb5eeec24b867527a
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
* Introduce a null check before calling `gpio_padbased_override`
in `variant_configure_pads`.
* This prevents potential errors in cases where the
`variant_gpio_override_table` function returns a null pointer,
indicating that there are no override pads to configure.
BUG=b:334826281
TEST=Able to avoid hang incase there is no GPIO override.
Change-Id: I733210a08091b37eda6e6b0d6924aafd5e7e6280
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82628
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The CHECK_REV_IN_OPROM_NAME Kconfig option was introduced to solve the
problem of the PCI VID/DID combination of the Picasso iGPU not being
sufficient information to know which VGA BIOS file to run, so a new
function that additionally checks the PCI revision of that device was
introduced. Later it turned out that there might be a case where even
that isn't sufficient, so the soc_is_raven2() function is used in the
remap function to always use the correct VBIOS file.
Picasso is the only SoC that selected the CHECK_REV_IN_OPROM_NAME
Kconfig option, so all other SoCs are unaffected by this change.
Now that we use the VBIOS images with only the PCI VID and DID in the
CBFS file name for Picasso, SeaBIOS will find the VBIOS with the same ID
as the iGPU in CBFS and we don't need the workaround to add a third
VBIOS image via VGA_BIOS_DGPU_* that has the name that SeaBIOS expects.
This will result in SeaBIOS now running the VBIOS that has the same PCI
VID/DID as the hardware which will be the wrong one in the RV2 silicon
showing the PCO silicon PCI VID/DID, but that was also the case with the
VGA_BIOS_DGPU_* workaround where the board's Kconfig just selected one
of the two possible images during build time and hoped that it was the
correct one for that actual hardware. The only board where this patch
might cause a regression compared to the old behavior is the AMD Cereme
reference board with Pollock APU, but I'm not even sure if any coreboot
developer still has one of those boards, so I'm willing to accept that.
To properly solve the problem with SeaBIOS using the correct VBIOS file
in all cases, we'd need to generate that info during coreboot runtime
and somehow pass it to SeaBIOS, but that's out of scope for this patch.
TEST=On Mandolin with PCO silicon, the display output in both SeaBIOS
and Ubuntu still works. Booting Windows 10 via the pre-built EDK2
payload that I'm using also resulted in the display output working.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia6de533c536044698d85404427719b8f534870fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82598
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Type-C kernel driver no longer programs the AP mux, as of
https://review.coreboot.org/c/coreboot/+/82077. So remove device
references to the TCSS Mux control device from the Type-C port driver.
This eliminates the following kernel error which was observed as a
result of the kernel trying to program muxes it no longer has control
over:
[ 4.618600] cros-ec-typec GOOG0014:00: Failed to get mux info for port: 0, err = -95
[ 4.618608] cros-ec-typec GOOG0014:00: Configure muxes failed, err = -95
BUG=b:341331428
TEST=Run system reboot; configure mux kernel errors no longer seen.
Change-Id: I93e498b12b109c0e649a23a4a49868976a9ee06b
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82599
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5208ceeec17051e7849263a4caa0838efd59c044
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82608
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iaf4478814e672fb8cfae5ffc4fa89c475f5bb0b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82607
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1) Add all changes needed for early graphics
2) select MAINBOARD_USE_EARLY_LIBGFXINIT for nissa
The InnoLux (N156HCN-EBA C7) panel is used for the device tree.
BUG=b:296433986
TEST=On-screen text message seen during MRC training on Craask
Logs:
[NOTE ] MRC: no data in 'RW_MRC_CACHE'
[SPEW ] bootmode is set to: 0
[0.171409] DP PHY mode status not complete
[0.175509] DP PHY mode status not complete
[0.179799] DP PHY mode status not complete
[0.184087] DP PHY mode status not complete
[0.188376] DP PHY mode status not complete
[0.192665] DP PHY mode status not complete
[0.196954] DP PHY mode status not complete
[0.201243] DP PHY mode status not complete
[0.205532] DP PHY mode status not complete
[0.209821] DP PHY mode status not complete
[0.214110] DP PHY mode status not complete
[0.218397] DP PHY mode status not complete
[INFO ] Informing user on-display of memory training.
Change-Id: I33cfc5d1f8c25c344e598befd21c50a78a65275a
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78932
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This board is the CWWK variant based upon Alder Lake with 4 2.5 GbE
ports, similar boards are available in other port configurations. As a
low cost, relatively high performance board with 4 NICs, it is well
suited for networking or 'homelab' tasks.
CPU: Intel N100 or N350
Memory: DDR5-4800 SODIMM (max 16 GB)
NIC: 4x Intel I226-V 2.5 GbE
Expansion:
- M.2 2230 E key
- M.2 2280 M key
- USB 2.0 header
- Fan header
External ports:
- DC power
- 4x Ethernet
- Display Port
- HDMI
- 4x USB 2.0
- Micro SD
Working:
- Boots Debian 12 with SeaBIOS and EDK II payloads
- Serial port
- External USB ports
- DisplayPort / HDMI
- 4x Intel I226 2.5 GbE NICs
- M.2 ports
- Micro SD slot
- ACPI S3
Not working / not tested:
- Fan (ITE IT8613E)
- Audio
- S0ix
- Internal USB ports
VBT extracted from vendor UEFI firmware version ADLN 0.01 x64
(04/04/2023 11:42:38).
Change-Id: Ice9174d95c10afc6a22ddd15fb3be4fa38d329be
Signed-off-by: Brandon Weeks <me@brandonweeks.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add Micron part MT62F512M32D2DR-031 WT:B only for Orisa.
DRAM Part Name ID to assign
MT62F512M32D2DR-031 WT:B 0 (0000)
BUG=b:337178014
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I559ed817250c40795e6c613794d4f65c636f5fc5
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82586
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 7088257b1ab715e93506619727e3bf589ea688fb.
Reason for revert: Intel suggest is NC only.
No need to change anything that isn't broken.
Change-Id: I976a85b35c69b03f1bc0ccd2bc7df923e47be815
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82572
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the `AZALIA_PIN_CFG_NC(0)` macro instead of `0x411111f0` and tidy up
some comments (align them and be consistent with capitalisation).
Tested with BUILD_TIMELESS=1, prodrive/hermes remains identical.
Change-Id: I1ff1197b1309fc0e5b978d6d36867a3f1a68c67c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
Now that we also have the devicetree registers for the USB PHY config
in the openSIL case, add the USB PHY config setting from the Phoenix
with FSP devicetree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3a0acbf1b9d705dbf09f4480eb35e71e587ddd44
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Use the now common get_ddi1_type function to update the connector type
of the DDI1 port to match the display output extension card plugged into
the reference board.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7c51eab0d32e0a1708da415f690689a8ec38dcd3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82583
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Both port descriptor files used in the FSP case contain an identical
get_ddi1_type implementation, so factor it out into a separate file.
This will also allow using the same function in the openSIL case in a
following patch.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6f5b75b9bdbdc67901d157079785c8fa2915bf0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82582
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a static DDI port configuration to the devicetree used in the
Phoenix with openSIL case. The configuration is taken from the
birman_ddi_descriptors array in port_descriptor_phoenix.c.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7b85b04114591f3e9da183019c98ca2cb08e59da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82581
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove the unexpected '<' char at the end of the comment about the PSPP
policy config.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id821351ce3a7a2b7844d8e7478fa3de3227a7da9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82579
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
Guard OCP functions calls to allow builds without OCP drivers.
Change-Id: Ie9a82387366a8bb3387bcba3ec7a4c7f0100f78c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Update Makefile to include fw_config file for mtlrvp board.
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: Id41cd8b015a796f7a959ceccf85106a48d15ae35
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82559
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit f867c9c5473156617691d78350c362cd993bfcdd.
The new verb table breaks external mic detection on brox.
Revert and use old verb tables instead.
BUG=b:330433089
BRANCH=main
TEST=Verified headset on Brox
When connected to audiojack in power_save state of legacy hda driver,
headset is detected and audio is resumed.
Change-Id: I0d8c092de6166b2c62f5ecc3deaf4960128e6106
Signed-off-by: Terry Cheong <htcheong@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82273
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Nova will use SOLDERDOWN. Add memory.c to override baseboard.
Update dram id table for correct platform parameter.
BUG=b:328711879
Change-Id: I6fbce991ef5ab9f0e6216ad1a5af73fcc1996a2a
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82474
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On GreenbayPOC, HDA Codec used is ALC236, different with Brox (ALC256)
Update to Realtek provided verb table for ALC236 audio codec.
BUG=b:336967284
TEST=Verified headset and audio workable on DUT with "rec" and
"aplay" command.
Change-Id: I9fbe57a0acab20387754f6b6cb5705e34c1c149b
Signed-off-by: Wu Garen <wu.garen@inventec.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82413
Reviewed-by: Ivan Chen <yulunchen@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add devicetree settings per the schematic.
Differences to gladios:
1. remove SD reader
2. remove EMMC setting
3. modify USB port distribution
FRONT
-------------------------------------------------------
| A3 A1 |
| C0 A2 A0 |
-------------------------------------------------------
BACK
-------------------------------------------------------
| --------------- |
| | TX25A | |
-------------------------------------------------------
BUG=b:327549688
TEST= USE="-project_all project_bujia" emerge-brask coreboot
Change-Id: Ia010e99c21e8d6088f6bb873f79dc19cadc9e455
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81447
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Refactor the `get_port_b_vref_cfg()` function to only return the
variable bits of the value. The NID itself is not connected, and
the `misc` field in the verb conveys the Vref value.
Change-Id: I5108f5339c5b002403a4e5339da6d52046c8bcbe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82395
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Probe C1 port in devicetree and disable un-used C1/A1 port by FW_CONFG.
BUG=b:339534479
BRANCH=firmware-dedede-13606.B
TEST=emerge-dedede coreboot chromeos-bootimage
flash and check boot log on DUT.
Change-Id: I944ff6f2fa712e7579ed1c9879f75835adc3ac4c
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Remove unused setting for retimer.
BUG=b:328711879
Change-Id: I48d8680d43a07aa3408dfbf5b25b568c2b51b343
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82475
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Beechnut City CRB is the 2 socket reference board for 6th Gen Xeon-SP
SP SoCs (Granite Rapids SP and Sierra Forest SP).
This patch initially sets the code set up as a compilation target with
GNR N-1 FSP, and with basic feature supports (Integrated IO Controller
(IIO) configuration, BMC, UART, HPET).
TEST=Build on intel/beechnutcity CRB
Change-Id: I3f6a0fb97b62baadb438fb9f11fdd78fccb3f89a
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Co-authored-by: Gang Chen <gang.c.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Avenue City CRB is the 2 socket reference board for 6th Gen Xeon-SP
AP SoCs (Granite Rapids AP and Sierra Forest AP).
This patch initially sets the code set up as a compilation target
with GNR N-1 FSP, and with basic feature supports (Integrated IO
Controller (IIO) configuration, BMC, UART, HPET).
TEST=Build on intel/avenuecity CRB
Change-Id: I64fdd5388aadf7732f6d3daa600c1455d3672a46
Signed-off-by: Gang Chen <gang.c.chen@intel.com>
Co-authored-by: Shuo Liu <shuo.liu@intel.com>
Co-authored-by: Jincheng Li <jincheng.li@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Instead of including stub/mpio/chip.h, include chip/mpio/chip.h that
will include the correct implementation to be able to use the same file
with both the openSIL stub and the actual openSIL implementation glue
code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iaae26a0dfe0ba96842e72582c06f1b0b3f29871c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82472
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch removes VPU enablement code that is no longer needed because
the VPU is already enabled by default in the baseboard devicetree.
BUG=b:332488817
TEST=Able to see VPU PCI device in lspci list after booting
google/screebo to OS
Change-Id: I94de92e970be1548068ed4e19309a95129f041ff
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82423
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch enables the Versatile Processing Unit (VPU) by default for
Rex/Ovis baseboard. VPU is a dedicated AI engine that is included in
the 14th generation "Meteor Lake" Core processors.
The VPU is designed to efficiently run AI models directly on the
system on chip (SoC). There is no power regression observed while
keeping the VPU default enabled to run AI models natively hence, this
patch enables the VPU by default.
BUG=b:332488817
TEST=Able to see VPU PCI device in lspci (0:11:0) list after booting
google/screebo to OS.
Change-Id: I8b3521c8ec613b002f971eaf9d346927fe8cd656
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
There is no direct way to override CPU default power_limits for
different SKUs.
This CL add structure variant_get_soc_power_limit_config() for
variants to define and configure the values of soc_power_limits_config
for current CPU SKU.
Variants can override these values i.e. pl1, pl2, psyspl2
in variant_devtree_update().
BUG=b:320410462
BRANCH=firmware-rex-15709.B
TEST=FSP debug emerge-ovis coreboot intelfsp
check overrides setting
Change-Id: Ib60fa4e3fc502d0aeb0c94ad46ba5a55b4dd027c
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82199
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on latest schematic to update the gpio table.
BUG=b:327549688
TEST= USE="-project_all project_bujia" emerge-brask coreboot
Change-Id: I3d01e3b9eaef72d9e143f5163ee49d8c8f455b5f
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82412
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Phoenix 2 has less PCIe lanes than Phoenix, so some of the lane end
numbers need to be adjusted to take that into account. When the Kconfig
options WLAN01 or WWAN01 are set, either the WLAN or the WWAN card uses
both PICe lanes that are available for those two devices, so the MPIO
descriptor information the devicetree needs to be updated accordingly
and the bridge to the PCIe port that doesn't have any lane left needs to
be disabled. Two other PCIe devices will be disabled when the
corresponding Kconfig options ENABLE_EVAL_CARD and DISABLE_DT_M2 have
the value that results in the device being disabled via some GPIO driven
by the EC. Since the code is specific to the openSIL case, only include
it in the build in the CONFIG_BOARD_AMD_BIRMAN_PHOENIX_OPENSIL case.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I23c14cc03980ea1e39f7e5aec551b975c237e487
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
Add the stub MPIO chips that contain the PCIe engine configuration for
the external PCIe interfaces to the devicetree. Birman's
port_descriptors_phoenix.c was used as a reference. The static
configuration in the devicetree assumes that the default WLAN0_WWAN0 is
selected; for the other cases we'll still need to fix up things
accordingly in the mutable devicetree. The WLAN01 and WWAN01 cases still
need to be handled in a follow-up patch. Since openSIL currently doesn't
use the info from the gpio_group struct element, but deasserts both PCIe
reset pins GPIO 26 and 27, the gpio_group isn't specified in the chip
configuration in the devicetree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Icabe60322d46c1195284dd77ec39f9d143e3d2cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Create the orisa variant of the nissa reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:337178014
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_ORISA
Change-Id: I0cd8d763ffd8864b455a7f8909e95f6aee8bb23e
Signed-off-by: EricKY Cheng <ericky_cheng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Amanda Hwang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Iccmax of VccIn_Aux is 25A with MBVR design.
BUG=b:330117043
BRANCH=firmware-nissa-15217.B
TEST=Local build successfully and boot to OOBE normally.
Change-Id: I105dc9df53c624fd7fc697408a1097e023a3cd68
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81445
Reviewed-by: Simon Yang <simon1.yang@intel.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add stop pin control for G2 touchscreen refer to
G7500_Datasheet_Ver.1.2.
BUG=b:335803573
TEST=build and verified touchscreen works normally
Change-Id: I4f085c67c0cdb8b9ca3ff03993fda69cca6319ef
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82254
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Copy the data.vbt from brox to greenbayupoc
BUG=b:326413034
TEST=emerge-brox coreboot chromeos-bootimage, flash and boot on DUT
Change-Id: I1e8101519ab2ecbb4654c20485fbe83c90656e4d
Signed-off-by: Eren Peng <peng.eren@inventec.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82108
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
