summaryrefslogtreecommitdiff
path: root/src/mainboard
AgeCommit message (Collapse)Author
2020-11-20mb/google/volteer/variants: Set TCSS PCIe RP0 to hidden by defaultDuncan Laurie
Set the default state of the TCSS PCIe RP0 to hidden so that coreboot does not allocate resources to this hotplug root port. The default behavior on the reference design is that there is only one USB4 port attached to port C1 while port C0 is only a USB3 port. Meanwhile the Voxel and Terrador variants do have USB4 on both C0 and C1 ports, so these boards change the default to 'on' so that coreboot does allocate resources for the hotplug port. BUG=b:159143739 BRANCH=volteer TEST=build volteer and voxel and check the resulting static.c to ensure the device is hidden or not. Also boot with the two different configurations and ensure resources are assigned or not. Finally check that S0ix still functions with the C0 port set to 'hidden' after authorizing a PCIe tunnel on port C1. Signed-off-by: Duncan Laurie <dlaurie@google.com> Change-Id: I8bb05ae8cd14412854212b7ed189cfa43d602c1d Reviewed-on: https://review.coreboot.org/c/coreboot/+/47198 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-20mb/google/volteer: Set up SATAXPCIE1 IOSSTATE based on detected deviceDuncan Laurie
There is an issue with the storage device being mis-detected on exit from S0ix which is causing the root device to disappear if the power is actually turned off via RTD3. To work around this read the RX state of the pin and apply the IOSSTATE setting to drive a 0 or 1 back to the internal controller. This will ensure the device is detected the same on resume as on initial boot. BUG=b:171993054 TEST=boot on volteer with PCIe NVMe and SATA SSD installed in the M.2 slot and ensure this pin is configured appropriately. Additionally test with PCIe RTD3 enabled to ensure suspend/resume works reliably. Signed-off-by: Duncan Laurie <dlaurie@google.com> Change-Id: I85542151eebd0ca411e2c70d8267a8498becee78 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47255 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2020-11-20mb/google/volteer: Enable RTD3 for SD cardDuncan Laurie
Enable the PCIe RTD3 driver for the PCIe attached SD card interface and provide the enable/reset GPIOs. These GPIOs are common across all variants so this is implemented in the baseboard devicetree with an fw_config probe if the device is present. The RTS5261 device does not have an enable GPIO so it is disabled in a workaround in mainboard.c, along with marking the SD-Express device as external. BUG=b:162289926, b:162289982 TEST=Tested on Delbin platform to ensure the system can enter the S0i3.2 substate and suspend/resume is stable. enabling this for the regular Genesys Change-Id: I40fe05829783c7bce2a2c4c1520a4a7430642e26 Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47377 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-20mb/google/volteer/variants: Enable RTD3 for the NVMe deviceDuncan Laurie
Enable Runtime D3 for the volteer variants that have GPIO power control of the NVMe device attached to PCIe Root Port 9. Enable the GPIO for power control for variants that do not already have it configured to allow the power to be disabled in D3 state. BUG=b:160996445 TEST=tested on delbin Change-Id: I6ebf813c6c3364fec2e489a9742f04452be92c45 Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46262 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-20soc/intel/common/acpi,mb/*: replace the two obsolete LPID with PEPDMichael Niewöhner
Replace the two obsolete LPID implementations with the new PEPD device. The PEPD device gets included in the plaforms' `southbridge.asl`, since it is required to load the `intel_pmc_core` module in Linux, which checks for the _HID. (See CB:46469 for more info on that.) There is no harm for mainboards not supporting S0ix, because the _DSM function won't be called with the LPS0 UUID on such boards. Such boards can use the debugging functionality of `intel_pmc_core`, too. Change-Id: Ic8427db33286451618b50ca429d41b604dbb08a5 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46471 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-19soc/intel/common/acpi: rename LPID to PEPDMichael Niewöhner
Rename LPID to PEPD for consistency. PEPD means "Power Engine Plug-In Device" and is the name Intel and vendors usually use, so let's comply. Change-Id: I1caa009a3946b1c55da8afbae058cafe98940c6d Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46470 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-19mb/google/zork: Set GPIO 86 high on bootMartin Roth
GPIO 86 should be set high on boot to save power. BUG=b:173340497 TEST=Build only BRANCH=Zork Signed-off-by: Martin Roth <martinroth@chromium.org> Change-Id: I31ef1d2a1967d82ba5370462783a909417088d2f Reviewed-on: https://review.coreboot.org/c/coreboot/+/47673 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Rob Barnes <robbarnes@google.com> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2020-11-19mb/google/volteer/var/terrador: Correct enable_gpio to GPP_F16David Wu
The GPP_F16 is for enable_gpio after check the schematic. BUG=b:151978872 TEST=FW_NAME=terrador emerge-volteer coreboot chromeos-bootimage Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: I63f43c231e624ed034ef18e8f06942ff3622d821 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47742 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Caveh Jalali <caveh@chromium.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
2020-11-19mb/clevo/cml-u/l140cu: Extend Kconfig option text with L141CUFelix Singer
Extend the Kconfig option text of L140CU with L141CU since the hardware of both is equal. Change-Id: If0e5061fc345208688a678a4cdf7c5ecaf47c17d Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47716 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2020-11-19mb/clevo/cml-u: Add comment to board selectionFelix Singer
Change-Id: I531865416b1bf9c5a73c809590059e7d7c8f373a Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47715 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-18mb/google/volteer: Add new Audio option to FW_CONFIGWisley Chen
Volteer has a new Audio option in FW_CONFIG. This patch adds support for it and when enabled, programs GPIO pins for I2S functionality. BUG=b:171174991 TEST=emerge-volteer coreboot Change-Id: I85bc37980957a3fb6c795858a4e4f44f3e3cc332 Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47291 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2020-11-18mb/google/hatch/var/ambassador: configure FSP option PcieRpSlotImplementedMatt Ziegelbaum
Ambassador is similar to puff. This change matches the PcieRpSlotImplemented configuration with Puff's, originally made for Puff in https://review.coreboot.org/c/coreboot/+/39986. Signed-off-by: Matt Ziegelbaum <ziegs@google.com> Change-Id: I5b6246f58c10e03a0d02278ad3621ded39bb6d6e Reviewed-on: https://review.coreboot.org/c/coreboot/+/47685 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-18mb/google/hatch/var/ambassador: update fan table and tdp configMatt Ziegelbaum
Fan table: provided by the ODM (see attachment in bug) based on measurements with EVT unit. BUG=b:173134210 TEST=flash to DUT Change-Id: I9f727f0f7e2eb7fe70385ebc843558d51e1860c5 Signed-off-by: Matt Ziegelbaum <ziegs@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47556 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-18mb/intel/adlrvp: Update HPD1/2 GPIO as per latest schematicsSubrata Banik
HPD_1: A19 -> E14 HPD_2: A20 -> A18 Change-Id: Idf3c8f4931bf8364bb9216a9369df7e05dcde047 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47683 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-18mb/google/asurada: Configure pins mode for SDWenbin Mei
Configure the pins for SD to msdc1 mode and change the driving value to 8mA. Enable VCC and VCCQ power supply for SD. Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com> Change-Id: I11151c659b251db987f797a6ae4a08a07971144b Reviewed-on: https://review.coreboot.org/c/coreboot/+/47008 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com>
2020-11-18mb/google/asurada: Implement enable_regulator and regulator_is_enabledYidi Lin
SD Card driver needs to access two regulators - MT6360_LDO5 and MT6360_LDO3. These two regulators are disabled by default. Two APIs are implemented: - mainboard_enable_regulator: Configure the regulator as enabled/disabled. - mainboard_regulator_is_enabled: Query if the regulator is enabled. BUG=b:168863056,b:147789962 BRANCH=none TEST=emerge-asurada coreboot Change-Id: I391f908fcb33ffdcccc53063644482eabc863ac4 Signed-off-by: Yidi Lin <yidi.lin@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46687 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-18mb/google/asurada: Implement board-specific regulator controlsYidi Lin
Currently, five regulator controls are implemented for DRAM calibration and DVFS feature. The regulators for VCORE and VM18 are controlled by MT6359. The reguatlors for VDD1, VDD2 and VMDDR are controlled by MT6360 via EC. BUG=b:147789962 BRANCH=none TEST=verified with DRAM driver Signed-off-by: Yidi Lin <yidi.lin@mediatek.com> Change-Id: Id06a8196ca4badc51b06759afb07b5664278d13b Reviewed-on: https://review.coreboot.org/c/coreboot/+/46406 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com>
2020-11-18soc/mediatek/mt8192: add pmic MT6359P driverHsin-Hsiung Wang
MT6359P is a PMIC chipset for Mediatek MT8192 platform. Reference datasheet: MT6359_PMIC_Data_Sheet_V1.5.docx, RH-D-2018-0205. BUG=b:155253454 BRANCH=none TEST=boot asurada correctly Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com> Change-Id: I62f69490165539847b8b7260942644533b15285b Reviewed-on: https://review.coreboot.org/c/coreboot/+/45399 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-18mb/google/volteer: Update flashmap descriptor to add ME_RW_A/B regionJamie Ryu
The current CSE firmware update implementation adds CSE RW binary to FW_MAIN_A/B and this increases the boot time due to the size increase of these regions leading to higher loading and hashing time. To mitigate this issue, CSE RW binary is moved from FW_MAIN_A/B to new region, ME_RW_A/B under RW_SECTON_A/B, and this updates the flashmap to add ME_RW_A/B region for CSE RW binary. BUG=b:169077783 TEST=build with cse rw binary, flash and verify volteer2 boots to OS. Verify me_rw binary is added to ME_RW_A/B region. Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com> Change-Id: I87da3824933ed2dd8e8ed0fed8686d2a3527faea Reviewed-on: https://review.coreboot.org/c/coreboot/+/46431 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-18mb/intel/jasperlake_rvp: Modify flash layout and enable CSE RW updateV Sowmya
This patch modifies flash layout to add ME_RW_A/B to add the CSE RW blob and also enable the CSE RW update feature for JSLRVP BUG=b:169077783 TEST= Built for jslrvp. Verified that CSE RW and metadata files are included in cbfs. Change-Id: I13baa317a06d00cec0337f08754892c7c8737f5d Signed-off-by: V Sowmya <v.sowmya@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47557 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2020-11-18mb/google/dedede: Modify flash layout to add ME_RW_A/B regionsV Sowmya
Existing implementation adds the CSE RW update binary to FW_MAIN_A/B regions and this has significant impact on boot time due to the increase in the size of these regions leading to higher loading and hashing time. This patch modifies flash layout to add new ME_RW_A/B fmap regions in the RW_SECTION_A/B. BUG=b:169077783 TEST= Built for dedede. Verified that CSE RW binary is added to the CSE_RW_A/B fmap region. Change-Id: I23a3e22a569488b39beb4d12f5b6309c7c742992 Signed-off-by: V Sowmya <v.sowmya@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47439 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-17mb/google/dedede/var/metaknight: Add touchscreen settingsTim Chen
Add Elan and Goodix touchscreen settings. BUG=b:169813211 BRANCH=None TEST=build metaknight firmware Change-Id: Ib2acd31a8076533c3b927d37127e7d27bac0bb57 Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47433 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2020-11-17mb/google/zork: Power off fingerprint sensor on shutdownMartin Roth
When the system shuts down, turn the fingerprint sensor off. This sets the GPIOs correctly for the next boot. The fingerprint sensor was previously left on, and was just powering down when the rails went low. On suspend, the fingerprint sensor stays awake and puts itself in a low powerstate mode based on the SLP_Sx_L pin states. BUG=b:171837716 TEST=Fingerprint sensor still works after S3, GPIO state on the boot following a shutdown is low. BRANCH=Zork Signed-off-by: Martin Roth <martinroth@chromium.org> Change-Id: I3837b58372d8f4a504535e76bd21c667d68f8995 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47311 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-17src: Add missing 'include <console/console.h>'Elyes HAOUAS
"Die()" needs <console/console.h>. Change-Id: I250988d77b0b0a093a1d116bea44a0cbb84189dd Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45540 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2020-11-17src: Add missing 'include <console/console.h>'Elyes HAOUAS
"printk()" needs <console/console.h>. Change-Id: Iac6b7000bcd8b1335fa3a0ba462a63aed2dc85b8 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45539 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2020-11-17mb/google/reef/variants/: add Naya NT6AN256T32AV-J2James Chao
BUG=b:172843935 BRANCH=coral TEST=emerge-coral coreboot chromeos-bootimage Signed-off-by: James Chao <james_chao@asus.corp-partner.google.com> Change-Id: I70195acc33218d3ad4c77acfdbc8f6ed93ab144e Reviewed-on: https://review.coreboot.org/c/coreboot/+/47382 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-17mb/google/zork: Assume VBOOT_STARTS_BEFORE_BOOTBLOCKMartin Roth
At this point, the zork platform will only use psp_verstage, so remove the VBOOT_STARTS_IN_BOOTBLOCK option and set code for VBOOT_STARTS- BEFORE_BOOTBLOCK to always be used. TEST=Build & Boot Morphius BRANCH=Zork BUG=b:172848137 Signed-off-by: Martin Roth <martin@coreboot.org> Change-Id: I30d90fe82c37966a860b52c07a3550dcecf8d19d Reviewed-on: https://review.coreboot.org/c/coreboot/+/47529 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-17mb/google/volteer/variants/volteer2: Tune Volteer2 I2C2 bus frequencyJohnny Li
The current I2C2 bus frequency is 344 kHZ, which does not meet the spec. This change updates scl_lcnt, scl_hcnt, sda_hold value for I2C2 to bring the bus frequency closer to 400 kHz. BUG=b:153588771 TEST=Verified that I2C2 frequency is 380 kHz. Signed-off-by: Johnny Li <johnny_li@wistron.corp-partner.google.com> Change-Id: I96fa5ed586de41324733ac7537b6bd73f39fc176 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47558 Reviewed-by: Caveh Jalali <caveh@chromium.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-17mb/google/octopus/variants/bobba: Add G2Touch touchscreen supportSheng-Liang Pan
Add G2Touch touchscreen support for bobba. BUG=b:171636614, b:169730666 BRANCH=octopus TEST=emerge-octopus coreboot chromeos-bootimage, and check touchscreen work. Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com> Change-Id: Ia361a56c050d7cbd7325b3c09fc34d8707441cc4 Reviewed-on: https://review.coreboot.org/c/coreboot/+/46808 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-16mb/google/hatch/dratini: Describe the privacy_gpioRicardo Ribalda
Add information regarding the privacy pin on the overridetree and gpio. BUG=b:172807539 Change-Id: Ic1bfa63e35a16d71a26adc3ec07b1ba36e6dc168 Signed-off-by: Ricardo Ribalda <ribalda@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47362 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-16mb/supermicro/x11-lga1151-series: Initialize mem_cfg in one lineAngel Pons
Change-Id: I50390f66d9570eb0fd703e3ad8a2735125d76b61 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47566 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Felix Singer <felixsinger@posteo.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-16dedede: Create lantis variantTony Huang
Create the lantis variant of the waddledee reference board by copying the template files to a new directory named for the variant. (Auto-Generated by create_coreboot_variant.sh version 4.2.0). BUG=b:171546871 BRANCH=dedede TEST=util/abuild/abuild -p none -t google/dedede -x -a make sure the build includes GOOGLE_LANTIS Change-Id: Ie3d15a687b870afc7d8bbeb6b5cab0792650da31 Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47510 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
2020-11-16mb/google/zork/: Enable REGULATORY_DOMAIN on VilbozEric Lai
WRDD table is needed for Intel WiFi module to enable SAR function. BUG=b:173066178 BRANCH=zork TEST=dump ACPI and check WRDD exist with Intel WiFi module. Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: I9fd6fd19ed188f7ab91faab9e2599b9b09ca5b22 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47554 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Amanda Hwang <amanda_hwang@compal.corp-partner.google.com>
2020-11-16volteer/variants/eldrid: Goodix touch panel power-on sequence tuningNick Chen
1. Enable panel stop GPIO in ramstage 2. generic.reset_delay_ms change to 30 BUG=b:171365316 Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com> Change-Id: I90ca39312252c668da6298183e598392bc9f9f28 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47502 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Caveh Jalali <caveh@chromium.org>
2020-11-16mb/google/zork: Init fingerprint GPIOs for boot vs resumeMartin Roth
Add a function that initializes GPIOs based on the sleep type that the system is coming back from. This allows initialization of the fingerprint GPIOs which need to be handled differently between wake from S3 and boot from S5. On initial boot, the state of the FP sensor could be either enabled or disabled. Because of this, on boot, we power off the sensor for >200ms, to reset its state, then power it back on. In suspend/resume, the fingerprint sensor should remain powered the entire time. If fingerprint is disabled on the trembyle-based board, set the pins to no-connect. Dalboz doesn't have fingerprint and the GPIOS are configured differently due to the FT5 chip having fewer GPIOS than FP5, so nothing needs to be initialized there. There were also a couple of trivial comment clean ups regarding the FPMCU GPIOS. BUG=b:171837716 TEST=Boot & Check GPIO states. BRANCH=Zork Signed-off-by: Martin Roth <martinroth@chromium.org> Change-Id: I16a2e621145782e0a908bb3e49478586c09a0e0a Reviewed-on: https://review.coreboot.org/c/coreboot/+/47308 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-16mb/google/volteer/var/voema: Add memory parts and generate DRAM IDsDavid Wu
This change adds memory parts used by variant voema to mem_parts_used.txt and generates DRAM IDs allocated to these parts. Added memory 1. H9HCNNNCRMBLPR-NEE 2. H9HCNNNFBMBLPR-NEE 3. MT53D1G64D4NW-046 WT:A BUG=b:172751925,b:172781673,b:172782100,b:172781562 TEST=emerge-volteer coreboot chromeos-bootimage Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: Ic832155448fb07152b906aa04ca49d384ec47b34 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47351 Reviewed-by: Caveh Jalali <caveh@chromium.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-16mb/google/kukui: Fix LCD sequence T3 fail issueTao Xia
The T3 that PPVARN_LCD low to LCM_RST_1V8 high is 0.1269ms and it does not meet the LCD specification that the T3 must be larger than 5ms. Because there is a delay between PPVARN_LCD_EN and PPVARN_LCD. An extra 9ms delay should be added on LCM_RST_1V8 in order to meet the specification "ProductSpec_NV105WUM-A51_ V4.3_P2(TLCM).pdf". BUG=b:172201138 BRANCH=kukui TEST=The LCD sequence T3 is larger than 5ms when power on. Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com> Change-Id: Iaf7ae494e30c4c207103d949287b335288688c54 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47443 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com>
2020-11-13mrc_cache: Move code for triggering memory training into mrc_cacheShelley Chen
Currently the decision of whether or not to use mrc_cache in recovery mode is made within the individual platforms' drivers (ie: fsp2.0, fsp1.1, etc.). As this is not platform specific, but uses common vboot infrastructure, the code can be unified and moved into mrc_cache. The conditions are as follows: 1. If HAS_RECOVERY_MRC_CACHE, use mrc_cache data (unless retrain switch is true) 2. If !HAS_RECOVERY_MRC_CACHE && VBOOT_STARTS_IN_BOOTBLOCK, this means that memory training will occur after verified boot, meaning that mrc_cache will be filled with data from executing RW code. So in this case, we never want to use the training data in the mrc_cache for recovery mode. 3. If !HAS_RECOVERY_MRC_CACHE && VBOOT_STARTS_IN_ROMSTAGE, this means that memory training happens before verfied boot, meaning that the mrc_cache data is generated by RO code, so it is safe to use for a recovery boot. 4. Any platform that does not use vboot should be unaffected. Additionally, we have removed the MRC_CLEAR_NORMAL_CACHE_ON_RECOVERY_RETRAIN config because the mrc_cache driver takes care of invalidating the mrc_cache data for normal mode. If the platform: 1. !HAS_RECOVERY_MRC_CACHE, always invalidate mrc_cache data 2. HAS_RECOVERY_MRC_CACHE, only invalidate if retrain switch is set BUG=b:150502246 BRANCH=None TEST=1. run dut-control power_state:rec_force_mrc twice on lazor ensure that memory retraining happens both times run dut-control power_state:rec twice on lazor ensure that memory retraining happens only first time 2. remove HAS_RECOVERY_MRC_CACHE from lazor Kconfig boot twice to ensure caching of memory training occurred on each boot. Change-Id: I3875a7b4a4ba3c1aa8a3c1507b3993036a7155fc Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46855 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-13mb/google/volteer/variant/lindar: Update devicetree settingsStanley Wu
Update I2C address for Goodix touchscreen and add ELAN touchscreen & Synaptics trackpad device. Follow CB:47415 to correct HID over I2C device to be level triggerd. BUG=b:160013582 TEST=emerge-volteer coreboot and check system dmesg and evtest can get device. Change-Id: I070fb0e06b588f128253270502c9c2c427c62b84 Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47390 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2020-11-13soc/intel/cnl: replace the remains of HeciEnabled by device state in dtMichael Niewöhner
The option `HeciEnabled` was partly replaced by use of the device on/off state in the devicetree in commit 3de90d1. The option has been removed from the corresponding boards, so `HeciEnabled` is always 0 and ME always gets disabled during soc finalize, when `HECI_DISABLE_USING_SMM` is set. Replace the option in the finalize function by the same dt state check that sets the FSP option and drop the remaints of `HeciEnabled`. Devicetrees still having `HeciEnabled` have been adapted to keep the current behaviour. Change-Id: Ib4cca9099b9aa3434552a41fbafca7cf6a0dd0eb Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47195 Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Felix Singer <felixsinger@posteo.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-13mb/intel/adlrvp: Update WWAN GPIO as per latest schematicsSubrata Banik
WWAN_RST#: E10 -> F14 WWAN_PWR_EN: E13-> F21 Change-Id: I7182f384eb7a404dfe623c64e29467b41c6b0bdd Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47519 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-13soc/intel/{skl,cnl}: replace PM ACPI timer dt option by KconfigMichael Niewöhner
Select `PM_ACPI_TIMER_OPTIONAL` to enable the new PM ACPI Kconfig and set the FSP option for PM ACPI timer enablement from its value instead of using the old devicetree option. Also drop the obsolete devicetree option from soc code and from the mainboards and add a corresponding Kconfig entry instead. Change-Id: I10724ccf1647594404cec15c2349ab05b6c9714f Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45955 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-13mb/hp/folio_9480m: Update northbridge ACPI filenameAngel Pons
Fix build errors, since `haswell.asl` was dropped in commit 79e3a1f8a5 (nb/intel/haswell/acpi: Merge `haswell.asl` into `hostbridge.asl`) Change-Id: Iaec5de2d74dd81c58a581bb511ba6a63629141aa Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47575 Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-13mb/supermicro/x11-lga1151-series: Fix up comment styleAngel Pons
Change-Id: I5b6191d2b5f6fd6d127934eda56e3c24181b0c4c Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47565 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Felix Singer <felixsinger@posteo.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-13mb/clevo/cml-u: Fix up comment styleAngel Pons
Change-Id: Idefc15fec1d62d68d88e91c76f59e1a60a3996b6 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47564 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Felix Singer <felixsinger@posteo.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-13broadwell: Flatten `acpi_init_gnvs` functionAngel Pons
Instead of relying on mainboards to call it, do like Lynx Point. Change-Id: Idb7457e0734e19d0a26f0762079e273b6e740475 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46793 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-13broadwell: Factor out `acpi_fill_madt` functionAngel Pons
It is identical for all Broadwell mainboards, thus deduplicate it. Change-Id: I74559fbe42e44aa4d15ced5d88f6c15a1bf5203b Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46792 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-13nb/intel/haswell/acpi: Merge `haswell.asl` into `hostbridge.asl`Angel Pons
Tested with BUILD_TIMELESS=1, Google Wolf remains identical. Change-Id: I710581156937b042ba4cf5948c65d0795ad37bbf Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46789 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-13soc/intel/broadwell/acpi: Rename `systemagent.asl`Angel Pons
Rename it to `hostbridge.asl`, which is what Haswell uses. Change-Id: I6f97fc5c9459fe6b66dcfcf51900c751beda0ebe Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46786 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-13mb/google/reef: Configure IRQs as level triggered for HID over I2CKarthikeyan Ramasubramanian
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4, the interrupt line used by the device is required to be level triggered. Hence, this change updates the configuration of the HID over I2C devices to be level triggered. References: [1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx BUG=b:172846122 TEST=./util/abuild/abuild Change-Id: Ifc6dd5f6549e7501f350afe8456a9a8096edcc25 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47425 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-13mb/google/poppy: Configure IRQs as level triggered for HID over I2CKarthikeyan Ramasubramanian
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4, the interrupt line used by the device is required to be level triggered. Hence, this change updates the configuration of the HID over I2C devices to be level triggered. References: [1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx BUG=b:172846122 TEST=./util/abuild/abuild Change-Id: Ida1b1d05b39e67a9eba3bfaecca37f38821a438b Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47423 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-13mb/google/kahlee: Configure IRQs as level triggered for HID over I2CKarthikeyan Ramasubramanian
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4, the interrupt line used by the device is required to be level triggered. Hence, this change updates the configuration of the HID over I2C devices to be level triggered. References: [1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx BUG=b:172846122 TEST=./util/abuild/abuild Change-Id: Ib2f203b5f5eea5c25cfd4543f5ed9f15101b1735 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47422 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-13mb/google/octopus: Configure IRQs as level triggered for HID over I2CKarthikeyan Ramasubramanian
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4, the interrupt line used by the device is required to be level triggered. Hence, this change updates the configuration of the HID over I2C devices to be level triggered. References: [1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx BUG=b:172846122 TEST=./util/abuild/abuild Change-Id: Ic334816712370da63471135da8dd598ab02d54ef Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47421 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-13mb/google/zork: Configure IRQs as level triggered for HID over I2CKarthikeyan Ramasubramanian
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4, the interrupt line used by the device is required to be level triggered. Hence, this change updates the configuration of the HID over I2C devices to be level triggered. References: [1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx BUG=b:172846122 TEST=./util/abuild/abuild Change-Id: I75a92616f11054993ff5a5bfefce5c3f4638c07c Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47420 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-13mb/google/drallion: Configure IRQs as level triggered for HID over I2CKarthikeyan Ramasubramanian
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4, the interrupt line used by the device is required to be level triggered. Hence, this change updates the configuration of the HID over I2C devices to be level triggered. References: [1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx BUG=b:172846122 TEST=./util/abuild/abuild Change-Id: Iff00667377eecedcf0b83bcfc0bf50bd4c3411eb Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47419 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-13mb/google/deltaur: Configure IRQs as level triggered for HID over I2CKarthikeyan Ramasubramanian
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4, the interrupt line used by the device is required to be level triggered. Hence, this change updates the configuration of the HID over I2C devices to be level triggered. References: [1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx BUG=b:172846122 TEST=./util/abuild/abuild Change-Id: I1773973f64bcc5ef6bd1856c5d8eb998bb6a4888 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47418 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-13mb/google/hatch: Configure IRQs as level triggered for HID over I2CKarthikeyan Ramasubramanian
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4, the interrupt line used by the device is required to be level triggered. Hence, this change updates the configuration of the HID over I2C devices to be level triggered. References: [1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx BUG=b:172846122 TEST=./util/abuild/abuild Change-Id: I320198d56131cf54e0f73227479f69968719b2a7 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47417 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-13mb/google/volteer: Configure IRQs as level triggered for HID over I2CKarthikeyan Ramasubramanian
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4, the interrupt line used by the device is required to be level triggered. Hence, this change updates the configuration of the HID over I2C devices to be level triggered. References: [1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx BUG=b:172846122 TEST=./util/abuild/abuild Change-Id: Ie7b82ea07ef97b2096d75229c445bd3a65cb3be0 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47416 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-13mb/google/dedede: Configure IRQs as level triggered for HID over I2CKarthikeyan Ramasubramanian
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4, the interrupt line used by the device is required to be level triggered. Hence, this change updates the configuration of the HID over I2C devices to be level triggered. References: [1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx BUG=b:172846122 TEST=emerge-dedede coreboot Change-Id: I9d8fa57ae0f554896a4a0722e3e89567676382d4 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47415 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-13mb/google/dedede/var/metaknight: enable USB2 port for cameraTim Chen
Enable USB2 port 5 for user facing camera. Enable USB2 port 6 for world facing camera. BUG=b:169813211 BRANCH=None TEST=build metaknight firmware Change-Id: Iecb7787d46eab7096dec9f838a16da101105e09a Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47391 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2020-11-13mb/google/dedede/var/metaknight: Disable I2C port 3Tim Chen
Disable I2C port 3 for metaknight BUG=b:169813211 BRANCH=None TEST=build metaknight firmware Change-Id: Ic4a056d53a8c8abd04a9b786428da0986a255276 Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47389 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2020-11-12mb/amd/mandolin/Kconfig: update help text for AMD_LPC_DEBUG_CARDFelix Held
The existing help text wasn't updated for Mandolin after it was copied from an older reference board and contained some information that doesn't apply to Mandolin. Change-Id: Ib34abb2ee8b289df5f7085957042fe00ad506ca9 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47481 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2020-11-12mb/amd/mandolin/Kconfig: add help text for the EC blobFelix Held
Change-Id: If8d3ebdb9a41330312c26fb5796c07de1b87b3eb Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47480 Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com> Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-12mb/clevo/l140cu: add CMOS layout and defaultsMichael Niewöhner
Add CMOS layout and defaults files and enable CMOS options in Kconfig. Test: changed loglevel setting, rebooted and checked the log. Change-Id: Ia1a27818b2d12fb7578189e5748b8073c8f928e3 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46311 Reviewed-by: Felix Singer <felixsinger@posteo.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-12mb/*/Kconfig: Annotate closing endif with corresponding conditionPaul Menzel
It’s common to annotate the closing endif, so do it for these four files. Change-Id: Ia5d071e1f544c9dea5af9c6bc3c605d9a0c5c0f5 Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47477 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2020-11-12Delete mainboard/google/chezaJulius Werner
Work on this mainboard was abandoned and never finished. It's not really usable in its current state, so let's get rid of it. Signed-off-by: Julius Werner <jwerner@chromium.org> Change-Id: I4cd2e2cd0ee69d9846472653a942fa074e2b924d Reviewed-on: https://review.coreboot.org/c/coreboot/+/47427 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-11soc/intel/tigerlake: Update Kconfig for NEM Enhanced ModeShreesh Chhabbi
This change switches the selection of CAR mode so that INTEL_CAR_NEM_ENHANCED_V2 is the default unless mainboard selects INTEL_CAR_NEM. INTEL_CAR_NEM is selected only by mainboards using older silicon (ES1 or ES2) that did not support NEM enhanced mode. This enables NEM Enhanced Mode for TGL-U/Y RVPs. Bug=b:171601324 BRANCH=volteer Test=Build coreboot for volteer. Boot on SKU that has 4MB L3 cache. Change-Id: Ib6e041261cb8ca9c6e602935da4962aac0d9ece5 Signed-off-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47259 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-11mb/hp/folio_9480m: Drop `sata_ahci` from devtreeAngel Pons
Commit 8084b38568 (sb/intel/lynxpoint/sata: Always use AHCI mode) dropped the devtree option, but missed this recently-added mainboard. Change-Id: I6ab3a763c0bcd7431193c48e473639589b1a1e1a Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47426 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2020-11-10sb/intel/lynxpoint/sata: Always use AHCI modeAngel Pons
The other two modes are not used by any mainboard, and the code seems to be copied from older southbridges. As the code looks incorrect, drop it. Change-Id: I374546279a85cead1aea13e0952bbfd6f643a75b Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47022 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2020-11-10mb/asus/f2a85-m: Disable `HUDSON_LEGACY_FREE` for working serial consolePaul Menzel
The Asus F2A85-M, F2A85-M LE and F2A85-M PRO all have a Super I/O, and therefore have legacy devices like a serial console. Selecting `HUDSON_LEGACY_FREE` currently disable the serial console during bootup in romstage, which is undesired. So, deselect the symbol by default. TEST=Boot Asus F2A85-M PRO and verify serial console is *not* disabled during romstage. Change-Id: Ia6588c0d4b2c24c7cb9da04805d13274c8ae295e Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47363 Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Mike Banon <mikebdp2@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-10mb/google/zork: Create Shuboz variantKane Chen
Create the shuboz variant of the zork reference board by copying the template files to a new directory named for the variant. (Auto-Generated by create_coreboot_variant.sh version 4.2.0). BUG=b:172021093 BRANCH=none TEST=emerge-zork coreboot Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com> Change-Id: I3f62625f8cbde1c9adf8ab335edeb9e811e32679 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47152 Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-10mb/hp: Add HP EliteBook Folio 9480mIru Cai
The code is based on autoport, with necessary modifications. This laptop uses SMSC MEC1322 embedded controller, but the EC interface is the same as the EliteBook laptops of previous generations that use KBC1126 EC. So it still uses ec/hp/kbc1126, but does not need EC firmware inserted into CBFS. We also need to leave the end of the OEM flash content untouched, so the default ROM size is set to 12MiB instead of 16MiB, and we need to modify the IFD when flashing. Thanks to persmule for providing the laptop and pointing out how to program the system flash chip of it. Change-Id: I2328c43cbb1f488aa1d0ddd9116814d971e5d8ae Signed-off-by: Iru Cai <mytbk920423@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45578 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-10mb/google/puff/var/dooly: Add WEIDA touchscreen deviceTony Huang
Adds ACPI properties for WDT8762A device. Per spec v0.8 HID name WDHT2002 T14=100ms BUG=b:163561649 BRANCH=puff TEST=emerge-puff coreboot and check system dmesg and evtest can get device. Change-Id: I178e9d5aa1e1501d33b3cd4092f3f522bb6f1a74 Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47280 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Sam McNally <sammc@google.com> Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
2020-11-09soc/intel/skylake: Enable PCH thermal depending on devicetreeBenjamin Doron
Hook up PCH thermal subsystem configuration to devicetree. Change-Id: I84bac2cec079370370ecf1e5e4742e6704921d40 Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47116 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Singer <felixsinger@posteo.net> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2020-11-09mb/emulation/q35: Define pm_acpi_smi_cmd_portArthur Heymans
The X86 Qemu targets use the AMD64 SMM save state, but unlike most AMD CPU's the PM ACPI SMI port is not configurable and uses the Intel default APM_CNT, 0xb2 port. This will be used by the common save state handler. Change-Id: Ifee9476f628a2df710fb4340ce6a19b008df1033 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45814 Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-09mb/intel/adlrvp: Replace if-else-if ladder with switch constructSridhar Siricilla
The patch replaces if-else-if ladder with switch case for readability purpose. Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com> Change-Id: I268db8bc63aaf64d4a91c9a44ef5282154b20a53 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47054 Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-09hatch: Create genesis variantMatt Ziegelbaum
Create the genesis variant of the puff reference board by copying the template files to a new directory named for the variant. (Auto-Generated by create_coreboot_variant.sh version 4.2.0). BUG=b:172620124 BRANCH=None TEST=util/abuild/abuild -p none -t google/hatch -x -a make sure the build includes GOOGLE_GENESIS Signed-off-by: Matt Ziegelbaum <ziegs@chromium.org> Change-Id: I70886c2c5a25f5de1a4941ff235547ee812fa50d Reviewed-on: https://review.coreboot.org/c/coreboot/+/47334 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
2020-11-09mb/intel/adlrvp: Add PMC.MUX.CONx device configuration for adlrvpV Sowmya
This patch adds the PMC MUX and CONx devices for adlrvp. Device specific method contains the port and orientation details used to configure the mux. BUG=b:170607415 TEST=Built and booted adlrvp. Verified the PMC.MUX CONx objects in SSDT tables. Change-Id: I3b5bb73991feb99577c16fea00c381dd0f855769 Signed-off-by: V Sowmya <v.sowmya@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47289 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subrata.banik@intel.com>
2020-11-09mb/purism/librem_cnl: Add new variant 'Librem Mini v2'Matt DeVillier
Add Kconfig entries, and update existing documentation to accomodate both v1/v2 versions of the board. Change-Id: I856bb914941211cfbec4fed871ba2a5a038e23c3 Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46984 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-09mb/purism/librem_mini: Fix USB_OC mapping in devicetreeMatt DeVillier
Correct USB over-current mappings in devicetree now that the GPIO config has been fixed per schematics. Change-Id: I564630231933c7c17a2c0a2a403fdcca9189b92e Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47222 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2020-11-09mb/purism/librem_mini: drop PcieRpSlotImplemented from LAN PCIeMatt DeVillier
The LAN NIC is onboard, not installed in a slot. Change-Id: I77ee7ee8c944b7942ca78d35cd881277c4030ab9 Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47252 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-09mb/purism/librem_mini: Update smbios_slot_desc for M.2/WLANMatt DeVillier
Add strings for M.2 keying and number of PCIe lanes. Change-Id: I2e13749b50263ee5c2388a419bc8d784af6bd880 Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47251 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-09mb/purism/librem_mini: Fix PCIe clock source mapping in devicetreeMatt DeVillier
Correct PCIe clock source mapping in devicetree now that the GPIO config has been fixed. Move ClkSrcUsage/ClkSrcClkReq registers under their associated PCIe root ports. Change-Id: Ibdaba51d971a39a6da6df82652b7420d7324dee5 Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47221 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2020-11-09mb/purism/librem_mini: Adjust GPIO pad config per schematicsMatt DeVillier
- set pads GPP_B6/B8 for PCIe CLK_REQ lines - set pad GPP_B14 to speaker output - adjust comment for GPP_C22 / USB3_P1_PWREN - set pad GPP_E4 to NF1 / SATA_DEVSLP0 - set pads GPP_E9/E10 to USB2_OC0#/USB2_OC1# Change-Id: I8bf8af620370ec2d4c864e513db5d710a9c65d27 Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47220 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-09mb/google/volteer/eldrid: Describe the privacy_gpioRicardo Ribalda
Add information regarding the privacy pin on the overridetree and the gpio. BUG=b:171888751 Change-Id: I1ab19a863715ba5a928dd7c16402d398e5475edc Signed-off-by: Ricardo Ribalda <ribalda@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46964 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-09mb/google/hatch/jinlon: Describe the privacy_gpioRicardo Ribalda
Add information regarding the privacy pin on the overridetree and gpio. BUG=b:169840271 Change-Id: Ifa628dda03f3f65976850aeabaf516f528a921b7 Signed-off-by: Ricardo Ribalda <ribalda@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46962 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-09mb/google/dedede/variants/magolor: Update Power Limit2 minimum valueSumeet R Pawnikar
Update Power Limit2 (PL2) minimum value to the same as maximum value for magolor board. DTT does not throttle PL2, so this minimum value change here does not impact any existing behavior on the system. BUG=b:168353037 BRANCH=None TEST=Build and test on magolor board Change-Id: I74e960de506d366cba2c8aefb23f9e69337fd163 Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47285 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2020-11-09mb/google/dedede/var/boten: Add LTE power on/off sequenceKarthikeyan Ramasubramanian
LTE module used in boten has a specific power on/off sequence. GPIOs related to power sequnce are: * GPP_A10 - LTE_PWR_OFF_R_ODL * GPP_H17 - LTE_RESET_R_ODL 1. Power on: GPP_A10 -> 20ms -> GPP_H17 2. Power off: GPP_H17 -> 10ms -> GPP_A10 3. Warm reset: Power off -> 500ms -> Power on Configure the GPIOs based on these requirements. BUG=b:163100335 TEST=Build and boot Boten to OS. Ensure that the LTE module power sequence requirements are met. Change-Id: Ic6d5d21ce5267f147b332a4c9b01a29b3b8ccfb8 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44588 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Peichao Wang <pwang12@lenovo.corp-partner.google.com> Reviewed-by: Marco Chen <marcochen@google.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-09mb/google/dedede: Add support for variant specific SMI sleep flowKarthikeyan Ramasubramanian
This support is required to power off certain components that exist only in certain variants. BUG=None TEST=Build and boot Boten to OS. Change-Id: Ib43ada784666919a4d26246a683dad7f3546fabb Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44587 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Peichao Wang <pwang12@lenovo.corp-partner.google.com> Reviewed-by: Marco Chen <marcochen@google.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-09mb/google/volteer/var/voema: Add memory parts and generate DRAM IDsDavid Wu
This change adds memory parts used by variant voema to mem_parts_used.txt and generates DRAM IDs allocated to these parts. Added memory 1. MT53E512M64D4NW-046 WT:E 2. MT53E1G64D8NW-046 WT:E BUG=b:171755775 TEST=emerge-volteer coreboot chromeos-bootimage Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: I24d466f92a7e0fa3ab2f6241f0b5af025c53ed98 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47228 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org> Reviewed-by: Caveh Jalali <caveh@chromium.org>
2020-11-09Atlas: Wake up AP on AC plug and unplugDaisuke Nojiri
This patch makes Atlas resume from S0ix by AC plug and unplug. BUG=b:165328935 BRANCH=atlas TEST=Put Atlas in suspend. Wake it up by AC plug. TEST=Put Atlas in suspend. Wake it up by AC unplug. Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Change-Id: I95676d785bfc1488a8c1bdd3d56f2c38d95f3fb6 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47144 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Caveh Jalali <caveh@chromium.org>
2020-11-09mb/google/dedede/var/drawcia: Remove camera EEPROM power resourceKarthikeyan Ramasubramanian
EEPROM in the camera module does not require any specific power resources. This will ensure that no unnecessary resources are turned on while accessing the camera EEPROM. BUG=b:167938257 TEST=Build and boot to OS in Drawlat. Ensure that the camera EEPROM is listed in the output of i2cdetect. Change-Id: Iece9b3f657bf94a21cc08bf1745353575858f9b2 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47230 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-09mb/google/dedede: Enable Wake on AC connect and disconnectKarthikeyan Ramasubramanian
Handle AC connect and disconnect notifications from Embedded Controller (EC) and wake from S3/S0ix. BUG=b:172266344 TEST=Build and Boot to OS in Drawlat. Ensure that the system wakes up from suspend on AC connect and disconnect on both the TypeC ports. 276 | 2020-11-04 12:21:29 | S0ix Enter 277 | 2020-11-04 12:21:40 | S0ix Exit 278 | 2020-11-04 12:21:40 | EC Event | AC Disconnected 279 | 2020-11-04 12:21:57 | S0ix Enter 280 | 2020-11-04 12:22:03 | S0ix Exit 281 | 2020-11-04 12:22:03 | EC Event | AC Connected 282 | 2020-11-04 12:22:35 | S0ix Enter 283 | 2020-11-04 12:22:47 | S0ix Exit 284 | 2020-11-04 12:22:47 | EC Event | AC Disconnected 285 | 2020-11-04 12:23:08 | S0ix Enter 286 | 2020-11-04 12:23:16 | S0ix Exit 287 | 2020-11-04 12:23:16 | EC Event | AC Connected Change-Id: I7fa4ac0096548fd63af86e9f56c4c1ee25491399 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47210 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-09mb/google/dedede/variants: Update Power Limit2 minimum valueSumeet R Pawnikar
Update Power Limit2 (PL2) minimum value to the same as maximum value for dedede variants (baseboard and drawcia). Currently, variants like boten, waddledee, waddledoo, metaknight and wheelie uses the DTT entries from baseboard devicetree since there is no override present for these variants. So, these variants will also reflect this change of PL1 minimum value. For madoo variant, PL2 minimum value already set the same as PL2 maximum value. DTT does not throttle PL2, so this minimum value change here does not impact any existing behavior on the system. BUG=None BRANCH=None TEST=Build and test on drawcia system Change-Id: I7ecf1ffcc7871192ebe18eb8c3c3fd3e1193721e Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47154 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-09mb/intel/jasperlake_rvp: Update Power Limit2 minimum valueSumeet R Pawnikar
Update Power Limit2 (PL2) minimum value to the same as maximum value for jasperlake rvp board. DTT does not throttle PL2, so this minimum value change here does not impact any existing behavior on the system. BUG=None BRANCH=None TEST=Build and test on jasperlake rvp board Change-Id: I862f7106846de5fb37f74419807eedc3096ded8a Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47201 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-09soc/intel/*/chip: Remove unused devicetree entryPatrick Rudolph
InternalGfx isn't used so drop it. Change-Id: I12f424d8d883e065ef8d007e56a8bff41a7fae53 Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47176 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-09mb/google/volteer/var/voema: config CSE LITEDavid Wu
Config voema to use CSE LITE BUG=b:171755775 TEST=FW_NAME=voema emerge-volteer coreboot chromeos-bootimage Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: Ic4ca82ce844e6367da70ed052445943572ae7b09 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47203 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2020-11-09mb/google/variant/voema: Select USE_CAR_NEM_ENHANCED_V2 for voemaDavid Wu
BUG=b:171755775 TEST=FW_NAME=voema emerge-volteer coreboot chromeos-bootimage Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: Ibedbbe8f9ac039cbde114ace3266ec067a4003ba Reviewed-on: https://review.coreboot.org/c/coreboot/+/47159 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2020-11-09mb/google/volteer: Skip TPM detection except on SPIJes Klinke
Production Volteer devices have Cr50 TPM connected via SPI, depending on Cr50 firmware version it may or may not support long enough interrupt pulses for the SoC to safely be able to enable lowest power mode. Some reworked Volteer devices have had the Cr50 (Haven) TPM replaced with Dauntless, communicating via I2C. The I2C drivers do not support being accessed early in ramstage, before chip init and memory mapping, (tlcl_lib_init() will halt with an error finding the I2C controller base address.) Since the Dauntless device under development can be made to support longer interrupts, or a completely new interrupt signalling mode, there is no need to try to go through the same discovery as is done via SPI. This CL will skip the discovery, enabling the S0i3.4 sleep mode in all cases, on the reworked test devices. BUG=b:169526865, b:172509545 TEST=abuild -t GOOGLE_VOLTEER2 -c max -x Change-Id: I08a533cede30a3c0ab943938961dc7e4b572d4ce Signed-off-by: Jes Bodi Klinke <jbk@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47049 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-09mb/google/volteer/variants/volteer2: Tune I2C3 camera bus freq 400 kHzJohnny Li
The current I2C3 bus frequency is 341 kHZ, which does not meet the spec. This change updates scl_lcnt, scl_hcnt, sda_hold value for I2C3 to bring the bus frequency closer to 400kHz. BUG=b:153588771 TEST=Verified that I2C3 frequency is 394kHz. Signed-off-by: Johnny Li <johnny_li@wistron.corp-partner.google.com> Change-Id: Ie1ef95bb39d71fbb113120a0ec88305bc23e7ab9 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47225 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Caveh Jalali <caveh@chromium.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-25 13:46:31 +0000