| Age | Commit message (Collapse) | Author |
|---|
|
The DPTF parameters were verified by the thermal team.
BUG=b:282598257
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I1f38ef52d3906960f8b692595fcc3b39bc000243
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Enabling MIPI UCAM for screebo project
BUG=b:277883010
TEST=none
Signed-off-by: jason.z.chen <jason.z.chen@intel.corp-partner.google.com>
Change-Id: Id06e5c162d911a4bd78190757c25e7f760160a8f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75157
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Haikun Zhou <zhouhaikun5@huaqin.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Set tcc_offset value to 20 in devicetree for Thermal Control Circuit
(TCC) activation feature for proto phase.
BUG=b:282865187
BRANCH=None
TEST=Build FW and test on Screebo board
Change-Id: I3a929aa20a700376d2a0a150911fed34e67f78eb
Signed-off-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75360
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Haikun Zhou <zhouhaikun5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Incorrect filename "MakeFile.inc" cause gpio.c can not be complied.
Rename to "Makefile.inc" and confirm gpio.c can load correctly.
BUG=b:281620454
BRANCH=dedede
TEST=build and confirm gpio.c can be loaded
Signed-off-by: Kevin Yang <kevin3.yang@lcfc.corp-partner.google.com>
Change-Id: I39947c66de04695e5242ab1affc328894f34f9f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75520
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move I2S config from common to board.
BUG=none
TEST=Build google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I51ca902e9b0077d5d5cc9c3507d26301a0f61bc2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75513
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable drivers for SoundWire codecs and define the topology in
the devicetree for the rex0 variant with the SoundWire daughter
board connected.
+------------------+ +--------------------+
| | | Headphone Codec |
| Intel Meteor Lake| +--->|Cirrus Logic CS42L42|
| SoundWire | | | ID 0 |
| Controller | | +--------------------+
| | |
| Link 0 +----+ +-------------------+
| | | Left Speaker Amp |
| Link 1 | +--->| Maxim MAX98363 |
| | | | ID 0 |
| Link 2 +----| +-------------------+
| | |
| Link 3 | | +-------------------+
| | | | Right Speaker Amp |
+------------------+ +--->| Maxim MAX98363 |
| ID 1 |
+-------------------+
This was tested by booting the firmware and dumping the SSDT table
to ensure that all SoundWire ACPI devices are created as expected with
the properties that are defined in coreboot under \_SB.PCI0:
HDAS - Intel Meteor Lake HDA PCI device
HDAS.SNDW - Intel Meteor Lake SoundWire Controller
HDAS.SNDW.SW00 - Cirrus Logic CS42L42 - Headphone Codec
HDAS.SNDW.SW20 - Maxim MAX98363 - Left Speaker Amp
HDAS.SNDW.SW21 - Maxim MAX98363 - Right Speaker Amp
BUG=b:269497731
TEST=Verified SSDT for SNDW in the OS. Playback and recording are also
validated on google/rex.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I3e11dc642ff686ba7da23ed76332f7f10e60fade
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73280
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The FBVDD_PWR_EN signal should be inverted in its control level
on Agah v.s. Hades. The original change covered the Hades
implementation, but needs to be updated to invert for Agah. This
change can be removed once we drop support for Agah.
BUG=b:280467267
TEST=built for Hades and Agah
Change-Id: I7f90c03b8d9b859004e5c124bf0a1f7b59921c3d
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75530
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Fine tune eMMC DLL settings based on Uldren board.
BUG=b:280120229
TEST=executed 2500 cycles of cold boot successfully on all eMMC sku.
Change-Id: I82a55a1fe17aa910eb02464df463603dcbbbef05
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75459
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ACPI DmaProperty for WLAN device. `is_untrusted` is eventually
ended up by adding DMA property _DSD which is similar to what
`add_acpi_dma_property` does for WWAN drivers, hence it makes sense to
have a unified name across different device drivers.
BUG=b:279676191
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I6d898a939aa0be31a671d2436a81c34f7a1ec030
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75460
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Add 'common_config.acp_config' to the device tree, so we have the
correct pin configuration.
BUG=b:225320579
TEST=USE=fwconsole emerge-skyrim ... ; verify 'devbeep' works in
depthcharge console
TEST=Boot into ChromeOS, verify YouTube sound works with internal
speakers and headphone jack
TEST=Boot into ChromeOS, verify microphone with Google Meet
Change-Id: Ie2d79408104273d8a53214b683800fa0663c14d3
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add beeps and blink SATA LED on critical errors.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I45b8b4fda00d58a1ab1d7dfab49d6f841bc0b000
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69821
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Incorrect memory part was used in CB:74745 to generate the DRAM Strap
ID. Amend the memory_parts_used.txt and regenerate the DRAM Strap ID.
BUG=b:272746814
TEST=Generate the DRAM Strap ID.
Change-Id: I0668d7e02345610a11f9113d8bbe99a474f33f1a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
BUG=b:283477280
TEST=Able to build and boot google/rex as per Proto 2 schematics
dated 05/16.
+-----------------+------------------------------------+---------------------------+--------+
| GPIO | In Proto 1 | In Proto 2 | Impact |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_C01 | SOC_TCHSCR_RST_L | SOC_TCHSCR_RST_R_L | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_D19 | NC | EC_SOC_REC_SWITCH_ODL | Y |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_E04 | HPS_INT_L | SOC_PEN_DETECT | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_E17 | EN_HPS_PWR | EN_PP3300_SPARE_X | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_F13 | GSPI1_SOC_MISO | GSPI1_SOC_MISO_R | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_F21 | GPIO_F21_SPI_CS_L | SPI_SOC_CS_UWB_L_STRAP | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_H00 | GPIO_H00_SPI_CLK_R | SPI_SOC_CLK_UWB_STRAP_R | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_H01 | GPIO_H01_SPI_MOSI_R | SPI_SOC_DO_UWB_DI_STRAP_R | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_H02 | GPIO_H02_SPI_MISO | SPI_SOC_DI_UWB_DO_STRAP | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_S00 | UNNAMED_8_METEORLAKEU_I137_GPPS00 | SDW_HP_CLK_WLAN_PCM_CLK | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_S01 | UNNAMED_8_METEORLAKEU_I137_GPPS01 | SDW_HP_DATA_WLAN_PCM_SYNC | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_S02 | UNNAMED_8_METEORLAKEU_I137_GPPS02 | DMIC_SOC_CLK0_WLAN_PCM_OUT| N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_S03 | UNNAMED_8_METEORLAKEU_I137_GPPS03 | DMIC_SOC_DATA0_WLAN_PCM_IN| N |
+-----------------+------------------------------------+---------------------------+--------+
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I4a8c43b0f845d3446188b7c926e482f91e5b45aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75407
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The IBM SBP1 is an evaluation platform.
It's utilising:
- 4 SPR sockets, having 16 DIMMs each
- 240C/480T at maximum
- 32x CPU PCIe slots
- 2x M.2 PCH PCIe slots
- Dual 200Gbit/s NIC
- SPI TPM
It has an AST2600 BMC for remote management.
It doesn't have:
- External facing USB ports
- Video outputs
- Audio codec
Test:
The board boots to Linux 5.15 with all 480 cores available.
All PCIe devices are working and no errors in ACPI.
All 64 memory DIMMS are working and M.2 devices can be used.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Change-Id: Ie21c744224e8d9e5232d63b8366d2981c9575d70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73392
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds two new chromeos_*.fmd files for release and debug FSP
builds targeting rex_ec_ish.
`rex_ec_ish` variant would pack ISH firmware into the CSE boot partition
hence, the blob size is expected to increase. Creates separate flash map
layout to ensure ISH work is not impacting on the regular `rex0` project
SPI flash usage.
BUG=b:284254353
TEST=Able to build google/rex_ish_ec board and boot on target hardware.
Change-Id: Ife4663d3ccf80a928646eadaac4c9ab49ad29055
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75471
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch creates a new variant to support the ISH enablement using
Rex platform.The idea here is to leverage the `rex0` code as much as
possible and add specific support for ISH enablement as per the hardware
schematic differences.
BUG=b:284254353
TEST=Able to build google/rex_ish_ec board and boot on target hardware.
Change-Id: I625fd0b31aed998f4e8f2d139827bc212ee8a90b
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75470
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Add support of variant_devtree_update() function to override
devtree settings for variant boards. Also, add CPU power limit
values for rex baseboard.
BRANCH=None
BUG=b:270664854
TEST=Built and verified power limit values as below log message
for 15W SKU on Rex board.
Overriding power limits PL1 (mW) (10000, 15000) PL2 (mW)
(57000, 57000) PL4 (W) (114)
Change-Id: If46445157358e3e0f227e26a35b4303fc9189a4b
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Harsha B R <harsha.b.r@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Restrict memory speed to 6400 MTS as per board design.
BUG=b:282164577
TEST=Verified the settings on google/rex using debug FSP logs.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I3dec383c7c585b80a73089f3403011c5cda61f65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Use verbs enabling jack detect if the EC firmware has been updated
with fixed jack detection.
Test: Build Librem 14 and boot with latest EC, test headset jack
detection.
Change-Id: I57a27b1d51e4f6c7c712bcb2823d21692b9c5ce6
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74364
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Based on the schematic and vendor ASL code, PCI interrupt lines ABC of
the Ricoh R5C847 PC Card/Media Card/FireWire controller are routed DBC.
From lspci and the schematic this chip is PCI device 1. The original
config copied from the T400 was routed ABCD->BCDA, causing Linux to
issue an "irq 18: nobody cared" message when inserting an SD card.
This is fixed by this patch and the SD card now works properly.
Change-Id: Iede1de72d5369f1aebbac170792733739add3431
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75411
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
"extern" is automatically implied with function declaration.
Change-Id: Ic40218acab5a009621b6882faacfcac800aaf0b9
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71890
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Use fw_config to probe lte.
BUG=b:283199751
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I5596f3536b0a21453f89e67615acabbbf6a8409b
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75337
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use fw_config to probe touchpad.
BUG=b:283199751
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: Ib20abac74683c670c174821b821ede461dbb0163
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Enable touchpad for Google Screebo.
BUG=b:278160238
BRANCH=none
TEST=Build and boot to Google Screebo. Verify touchpad works.
Change-Id: Ib83e5ef5ca497592f5a26aa1e85d793d06d9dd7f
Signed-off-by: Zhongtian Wu <wuzhongtian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75412
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Commit f99d6700 ("mb/google/skyrim/var/winterhold: Fix USB port ACPI
generation") fixed the USB-A ports being double-nested, but neglected
to move the chip driver registers up into the correct scope. While the
generated ACPI is still correct, fix the register scope anyway to
avoid confusion.
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot winterhold, dump ACPI, verify unchanged
Change-Id: Ia9982fed0fe2093d787ee9506ac5bbadd6cc03f9
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75389
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Commit d81ee3f1 ("mb/google/skyrim/var/markarth: Fix USB port ACPI
generation") fixed the USB-A ports being double-nested, but neglected
to move the chip driver registers up into the correct scope. While the
generated ACPI is still correct, fix the register scope anyway to
avoid confusion.
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot markarth, dump ACPI, verify unchanged
Change-Id: I5c1cd23c49b512f55e9e13b2164d30dfb7fb682d
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75388
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Commit a539893c ("mb/google/skyrim/var/frostflow: Fix USB port ACPI
generation") fixed the USB-A ports being double-nested, but neglected
to move the chip driver registers up into the correct scope. While the
generated ACPI is still correct, fix the register scope anyway to
avoid confusion.
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot frostflow, dump ACPI, verify unchanged
Change-Id: I3912fe1b7d3f2a07cb379928cd4f5d87100d3284
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75387
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch overrides `SaGv` FSP-M UPD to enable SaGv feature to be
able to train memory (DIMM) at different frequencies.
On all latest Intel based platforms SaGv is expected to be enabled
to support dynamic switching of memory operating frequency.
BUG=b:267879107
TEST=Able to verify SaGv is enabled with 3 work point (0, 1 and 2)
and MRC retraining takes around ~20ms extra compared to SaGv being
disabled.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ic680bfeab4dd285c0d3916ba5e917cc12bae3284
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73534
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SKU1A C0 has no redriver, so enable SBU muxing in the SoC.
BUG=b:283044004
BRANCH=none
TEST=Voltages are correct on the C0 and C1 AUX bias pins
Change-Id: I18b4ade2c60c270855fb2e733a9201539e08d8ba
Signed-off-by: mike <mike5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Enabling BT for screebo project
BUG=b:278169273
TEST=Check whether BT can connect to Bluetooth device
Signed-off-by: qinwentao <qinwentao@huaqin.corp-partner.google.com>
Change-Id: I0ecd62abfbe751e1036948b1490844e7e63d7f0d
Signed-off-by: qinwentao <qinwentao@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75352
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Hades uses the SODIMM, enable the smbus to see the SPD address for the
memory.
BUG=b:283138024
TEST=i2cdetect -l can see the smubs adapter.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I3912a025afaf8388d04a4b08852a84d4a2a6bf06
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75399
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add devicetree and Kconfig entries to enable additional configuration
of the Pericom PI7C9X2G608GP PCIe switch on this board variant.
The amplitude is being adjusted to 425 mV and de-emphasis level to
6.0 mV.
BUG=none
TEST=Read out the PCIe config space values of the switch and check if
they match with the ones configured over SMBus.
Change-Id: I11459f0794278ad614aa6e16c56df1ad578fe2f8
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
To improve the rate of data transfer for PCIe root port #2 (00:1c.1) and
root port #3 (00:1c.2) set the max payload size to 256 bytes for both
root ports.
Change-Id: I553f6cf090d799fbbaafb925646c6566d6951a86
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75127
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
|
|
Use fw_config to probe touchscreen.
BUG=b:283199751
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I5d8129b3af3aa09e5bc31160de82d9ef7af0dd59
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Override the weak function mainboard_ewl_check() and select OCP_EWL.
Select IPMI_KCS_ROMSTAGE and IPMI_OCP for OCP IPMI commands which are
needed for OCP EWL driver, but they are Meta-specific BMC commands
and don't really work for AC, this change is just for a demonstration
with AC.
Note that FSP UPD promoteWarnings needs to be disabled so that
FSP won't block and can return to coreboot for EWL processing
when memory EWL type 3 error occurs.
Tested=On Intel AC, connected with a faulty DIMM can see
EWL type 3 error being generated and halted with coreboot log:
[DEBUG] Number of EWL entries 3
[ERROR] EWL type: 3 size:32 severity level:1
[ERROR] Major Warning Code = 0x29, Minor Warning Code = 0x04,
[ERROR] Major Checkpoint: 0xb7
[ERROR] Minor Checkpoint: 0x74
[ERROR] Socket 0
[ERROR] Channel 4
[ERROR] Dimm 0
[ERROR] Rank 0
[ERROR] IPMI: ipmi_get_board_config command failed (ret=3 resp=0xc1)
[DEBUG] ipmi send memory training error
[DEBUG] EWL type: 1 size:19 severity level:1
[DEBUG] 0x6392e968: 01 00 00 00 13 00 01 00 00 00 b7 74 0a 03 00 04
[DEBUG] 0x6392e978: 00 00 00
[DEBUG] EWL type: 1 size:19 severity level:1
[DEBUG] 0x6392e97b: 01 00 00 00 13 00 01 00 00 00 b7 74 0a 03 00 04
[DEBUG] 0x6392e98b: 00 00 01
[EMERG] Memory Training Error!
Change-Id: I4602ae356aa6e55ed0611b8ac9a206db127c297c
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=untested, but same error/fix as frostflow variant.
Change-Id: Ic498afcc8b8e0224f344f405e2f1ef6184df1d6b
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75340
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=untested, but same error/fix as frostflow variant.
Change-Id: Ie40541ada508acfa5771ea800249b8a57b168e3b
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75339
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot frostflow, verify error no longer present in dmesg.
Change-Id: I0b87af6b2c04f9354e6f394a8f987fa660e49134
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75338
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Generate the RAM ID for Samsung K3KL6L60GM-MGCT.
DRAM Part Name ID to assign
K3KL6L60GM-MGCT 6 (0110)
BUG=b:273791621
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I05a2cd5f2235702dea8fd706349ebda6a9ffa2ef
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Add `ramtop` to CMOS layout so SOC_INTEL_COMMON_BASECODE_RAMTOP
can be used.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I88128d2c62bdc3246a3f30e768c353f0fe3faeb7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74432
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
BUG=b:282912666
TEST=set and unset bit20 in HW_CONFIG and check if VPU(0b.0)
is enabled when bit20 is set, and disabled when cleared
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: Iee6a9026a4d210407350bfb7ecc8a058e7ff5c24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
TEST=set the corresponding cbi bit, and saw SPI0 under sysfs
BUG=b:278783755
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I7099cde14cff90ad63e9164769f9913a8284a805
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
According to Thermal table 0518, adjust DPTC and STT settings.
BRANCH=none
BUG=b:273636128
TEST=emerge-skyrim coreboot chromeos-bootimage
Then the thermal team has verified.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Id1c1884eabc1ea58148270f39eaca836ccc3fb54
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chao Gui <chaogui@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Amanda Hwang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
The board needs this setting to boot.
Change-Id: I7f507c2478b63daf891430e95b008747b9b95a51
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
The Gazelle 18 (gaze18) is a Raptor Lake-H board.
Tested with a custom TianoCore UefiPayloadPkg.
Working:
- PS/2 keyboard
- I2C HID touchpad
- Both DIMM slots
- M.2 NVMe SSD slot
- M.2 SATA SSD slot
- All USB ports
- Webcam
- Ethernet
- WiFi/Bluetooth
- Integrated graphics using Intel GOP driver
- Internal microphone
- Internal speakers
- Combined headphone + mic 3.5mm audio
- 3.5mm microphone input
- S3 suspend/resume
- Booting Pop!_OS Linux 22.04 with kernel 6.2.6
Not working:
- Discrete/Hybrid graphics
Change-Id: I4599bf12c0f3048f9328f336cc8971400f5fd1a0
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
Pujjoteen5 support WWAN 5G device, use variant.c to handle the
power on sequence.
BUG=b:279835626
TEST=Build and check WWAN 5G power on sequence.
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I7dc72f2c705bcb41745f4bf08bef286773fe8b13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75327
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Measured the I2C frequency meets spec
1. I2C0 (TPM): 976.1 Khz
2. I2C1 (TouchScreen); 394.0 Khz
3. I2C2 (WCAM); 377.9 Khz
4. I2C3 (Audio): 390.0 Khz
5. I2C5 (Touchpad): 389.3 Khz
BUG=b:283374537
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
and check all I2C devices measurement result
Change-Id: If6e3a4a2b1ac642561015a290e6579238c3c2b1b
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Set the DmaProperty in the device's _DSD so that the OS can treat the
device as untrusted.
BUG=b:278310256
TEST=cat /sys/bus/pci/devices/<wifi>/untrusted == 1
iperf3 -c <iperf3-server> -t 60 (No performance regressions seen)
Change-Id: I06369a19afa5b881b26f5c1eb243e2db41a9bb36
Signed-off-by: Mark Hasemeyer <markhas@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75095
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
Set all GPIOs to their target functions and do not depend on FSP to
configure them. The board support has stabilized and was tested with
many PCIe devices. There is no need to detect CLKREQ signals so we may
hardcode them.
TEST=Boot MSI PRO Z690-A DDR4 to Linux and check if all ASPM and Clock
PM features' state on PCIe root ports are the same before and after
the change.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I01dc83ce23ca27525b8905665da942510f249824
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Disable backlight before turning on bridge, otherwise the bridge will
initialize failed.
Fixes: d5c1e1(mb/google/corsola: Add support for MIPI panel)
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I7d10bf9e8675b2fb03bfd1e294af66207b9b0620
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75354
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
BUG=b:278156430
TEST=verify the fingerprint on screebo
Change-Id: I986e470b28145f7b17427e794055929a4283c721
Signed-off-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75287
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dolan Liu <liuyong5@huaqin.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
The upstream kernel privacy screen driver uses HID GOOG0010 to look for
firmware node to use. This method is used on other boards, e.g. redrix.
See: drivers/platform/chrome/chromeos_privacy_screen.c in linux sources.
Update jinlon gfx ACPI node to work with that.
BUG=b:279092050
TEST=privacy protection screen works with 5.15 and 4.19 kernels
Change-Id: Icba41e7f2be7292f713fea10dbe69b3ca128bde7
Signed-off-by: Kornel Dulęba <korneld@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75289
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Disable unused gpio for LTE daughter board, WFC and stylus.
BUG=b:277148122
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I6cc61321cd96a10dd34ff6cd9fcabe85a64bbfa9
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75293
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The support for the board has stabilized and PCIe ports have been
tested with many devices. Although hotplug is not commonly used
and it seems pointless to keep it enabled, so disable it.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I338c55cb57d971badd08235b71626a710fafb829
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Select INTEL_GMA_HAVE_VBT so VBT files are added by default. This board
has two specific VBT files that are hard-coded in the Makefile. Hence
set an empty INTEL_GMA_VBT_FILE string.
Change-Id: I0508c8016da06b401d6fbefd6e5cec1af018a5c8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
There is only a single place where we need the LVDS EDID string. Let's
call gm45_get_lvds_edid_str() right there. This simplifies the API and
helps to follow the execution flow.
The function is moved to avoid a forward declaration.
Change-Id: I86f3a88e6b661bcf60319edbe301e70304924727
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The PCI resource should only be probed as part of the device
.init process. We can simply do that first and know that we
can use the global `gtt_res` from then on.
This simplifies the signature of gm45_get_lvds_edid_str(), and
makes changes to the API user (lenovo/x200) necessary.
Change-Id: I6c96f715abfa56dcb1cd89fde0fbaef3f1cb63ae
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
As announced in the 4.20 release notes, support for the Intel Galileo
mainboard is moved to the 4.20 branch and dropped from master.
Change-Id: I132adf2782721738c954252665fdcd7bb8e1a1cd
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63284
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: ron minnich <rminnich@gmail.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Generate the RAM ID for Samsung K3KL6L60GM-MGCT.
DRAM Part Name ID to assign
K3KL6L60GM-MGCT 6 (0110)
BUG=b:281928906
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: Ia5193d3ab3d654f25d519ad9a954f2ca8a15a978
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75152
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@google.com>
|
|
GC6 - Low power mode for system idle on Nvidia GPU
In GC6I Before ramp of PEXVDD:
Deassert FBVDDQ Enable, no delay is needed before or after.
In GC6O After ramp of PEXVDD:
Assert FBVDDQ Enable, no delay is needed before or after.
BUG=b:280467267
TEST=built for Hades and Agah, tested on Agah
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I0277772b1d2f6f4e6a3f74b92035e8b36f2670ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75302
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables stylus support by configuring the "GPP_D08" irqs for
rex SoC. This allows the SoC to detect a stylus device, when in use.
However stylus is not a wake up source for the rex.
BUG=b:282256460
Test=Stylus is detected on proto1 device.
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Change-Id: I84a71aa664698e105b738f8680d0a4751ca1fc72
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Phoenix has one more Type C port and two more USB2 ports which are used
as the legacy USB part of the two USB4 ports. The USB struct version
numbers have also changed, since it's a newer and incompatible version
of that struct.
TEST=After changing FSP to not hard-code the USB PHY config, but use the
configuration provided by coreboot, and applying this patch, the USB
connector on the USB2 port 4 lines works.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If52934595dd612154b97e7b90dbd96243146017a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73379
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Things with prompts should not use selects, but should instead default
to y. If there's a reason they need to be selected, they should be able
to be hidden when they're selected.
This isn't one of those cases where a select is needed, so set the
default to y instead.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: If6de339c3a1ceb3cd71008402bba49b5efc4af3f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
The SPD format in the APCB has changed for Phoenix, and the injection
tool 'apcbtool' needs to be updated to match. Until this happens, the
APCB will be built containing the correct SPD.
BUG=b:281983434
TEST=Build
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: If575f98511c796e93c5a12cd450a3a7985e39806
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
This hook is specifically for asus/p3b-f so its mainboard code has
a chance to put SPD away after RAM init completes. What it intends
to do is done when GPO gets programmed in ramstage (and it's safe
to do so), and no other board needs this hook, so drop it.
Change-Id: Ib7874b4d2b69fdaa5f3c5a3421a62a629c4154a4
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Pujjoteen5 support WWAN 5G device, add GPIO setting for WWAN 5G device
BUG=b:281943398
TEST=Build and check serial log
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: Ie2e0ea34c54a453645d626f892f50654ef5064ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75195
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pujjoteen5 support WWAN 5G device, enable PCIe port 3 for WWAN 5G device
BUG=b:281943398
TEST=Build and boot on pujjo
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I6d2e8eaecae968ed51095d9497beab492ba7e0c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
BUG=b:280843816
TEST=builds
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I55a85335a34eee227abb6ff355719f7ca2cbf04a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Use AUDIO PROBE to determine speaker amp config, set SOF driver
profile accordingly.
TEST=build/boot Win11 on Delbin and Drobit, verify correct audio profile
selected, drivers loaded and functional.
Change-Id: I13d787cb5ccb74d2774151ccd5deeb45b3364319
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Taniks uses a 4-channel output config, rather than 2-channel.
Update the SOF speaker topology accordingly.
TEST=build/boot Win11 on taniks, verify speaker output functional.
Change-Id: I3c08b12b11464dcada014289174e0cc468d1c39d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
By moving certain FW UI assets from RO to RW sections, 4 MiB is
sufficient for RO section. Split the resultant available 4 MiB equally
between 2 RW sections. This will help in getting to 16 MiB SPI flash for
the mainboard.
BUG=b:281567816
TEST=Build Myst BIOS image with the updated layout.
Cq-Depend: chromium:4519688
Change-Id: I09948ceac0a6a1cb109322fc4856b8b486318664
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75184
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
Update USB port macros:
- change onboard ports to SHORT: MYSTIC LIGHT, LAN_USB1, PS2_USB1,
HUB to USB 2.0 headers, HUB to rear USB 2.0
- change USB type C header to LONG which caused hard lockups on the
port making it unable to enumerate in UEFI Payload and Linux
- add empty definitions for USBr ports
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I91198aa713e9084ff3906c267ee1b37b10c71843
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69820
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
copy from dibbi since taranza base on dibbi,this is only for first
initial configuration, will update the more setting afterward.
BUG=b:277664211
BRANCH=dedede
TEST=build
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ia319f65897c0fea2f0558c20a5bc36bb6fbaea96
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts.
BUG=b:277664211
BRANCH=dedede
TEST=build
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I6bbb67ccdd8ebc21719921d00320907f8dbb285f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74933
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds support for variant specific chip config update similar
to commit 061a93f93d2 ("mb/google/brya: Add variant specific soc chip config update").
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I60a4042cba608fd527527af9340ec0215f3086ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75046
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
add initial devicetree config for screebo
BUG=b:276814951
TEST=emerge-rex coreboot
Change-Id: Ie64d0e50ec22b3e363597af64eb723ef1f86dfa8
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The detachable Starmie will use MIPI panels, which require reading
serializable data from the CBFS. So we add MIPI panel support to the
display configuration and align the configuration sequence with the
panels that use MIPI bridges.
The PMIC Datasheet:
TPS65132-Single-Inductor-Dual-Output-Power-Supply.pdf
BUG=b:275470328
BRANCH=corsola
TEST=emerge-corsola coreboot chromeos-bootimage and display normally
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I6f079e54f0317ff2f685f0e3834ebd1ceb8e9fcb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Error message ´Cannot map compressed file config without cbfs_cache' is reported.
Compressed parts of CBFS can not be used during bootblock stage.
Remove config from mb_log_list.
Will be added to verified items by CB:74752.
BUG=NA
TEST=booting and verify log on facebook FBG1701
Change-Id: Iacf023bc8b9c2ebc66137c4ea683589751a30d2f
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add wifi sar table for uldren
BUG=b:279679700
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I9e3d7a06beb673b204f2dfe8e7beb919730aa885
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
BUG=b:278022971
TEST=verified on screebo
Change-Id: I16f1d66ca7f885120358eb2a2d3c6fb111319f11
Signed-off-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75173
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When using a 32-MiB ROM chip, the ABL leaves the SPI flash in 4-byte
addressing mode, so ensure the driver exits that mode for regular
operation.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I9a846be743a65ffe5b3ef94e20e0b5fc5e273961
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
TPM IRQ should be A20 not A13. RAM table is correct.
BUG=b:282164589
TEST=able to boot up
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I82a709cc280288d612c65697b8da3c4274d4cd3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75191
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow schematic to correct I2C bus.
BUG=b:282164589
TEST=able to boot up
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I277e5190302c98dbce809d09c1a32fac758aa8e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Adjust the touchpad HID/CID/HRV to allow coolstar's crostouchpad
Windows drivers to properly attach. Change the interrupt type
from EDGE to LEVEL.
TEST=build/boot samsung/lumpy, verify touchpad functional under
both Windows 10/11 and Linux, verify Windows overlay driver
correctly remaps top row keys.
Change-Id: Ie4268b4de5779ee148699c7bef8c700a99816f1e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Adjust the touchpad HID/CID/HRV to allow coolstar's crostouchpad
Windows drivers to properly attach.
TEST=build/boot google/parrot, verify touchpad functional under
both Windows 10/11 and Linux, verify Windows overlay driver
correctly remaps top row keys.
Change-Id: Ic164244eceb52221653bd60f7217f9a09e38c1b6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75180
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust the touchpad HID/CID/HRV to allow coolstar's crostouchpad
Windows drivers to properly attach. Change the interrupt type
from EDGE to LEVEL.
TEST=build/boot google/butterfly, verify touchpad functional under
both Windows 10/11 and Linux, verify Windows overlay driver
correctly remaps top row keys.
Change-Id: I971795becfb05fb42921ff6f40a20892f4f5654a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Use board-specific ASL for PS2-attached trackpad rather than the EC/SIO
default, so that Windows installs a multitouch-capable driver rather
than the standard PS2 mouse driver.
TEST=build/boot Win11 on google/stout, verify trackpad is multitouch
capable.
Change-Id: Id93bbe53f35b1e2c35e36d8175889786b9f5de8b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75176
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
VMX is enabled through a bit in the IA32_FEATURE_CONTROL MSR, which can
be locked. The MSR remains locked after a non-power cycle reset, though.
If the MSR is locked, coreboot bails out and leaves VMX in the state it
was found. Because of this, changes to the VMX enable option in the BMC
only take effect after the system is power cycled.
This behaviour is highly undesirable because users are likely not aware
that a power cycle is required for changes to VMX state to take effect.
So, if VMX is supported, the IA32_FEATURE_CONTROL MSR is locked and the
current VMX state does not match the requested state, then issue a full
reset. This will power cycle the system and unlock the MSR, so that the
desired VMX state can be programmed into the MSR. This is checked early
to avoid needlessly doing time-consuming operations (running FSP) twice
if we know we will need to power cycle the system anyway.
Note that a user may change the VMX setting after the newly-added check
but before the setting is read in ramstage to program the MSR, but this
is a non-issue as firmware settings need a reset to take effect anyway.
TEST: Toggle VMX setting in BMC and reboot without power cycle, observe
coreboot automatically issues a power cycle reset because the MSR
is locked and the VMX state differs. Verify that the system boots
properly with VMX in the correct state after having power cycled.
Change-Id: Id9061ba896a7062da45a86fb26eeb58927184dcb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Instead of having the maximum number of possible CPU objects defined in
the DSDT, dynamically generate the number of needed CPU devices in the
SSDT like it's done on all other x86 platforms in coreboot.
TEST=APU2 still boots and Linux doesn't show any ACPI errors with this
patch applied and it prints "ACPI: \_SB_.P000: Found 2 idle states".
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id6f057ad130a27b371722fa66ce0a982afc43c6c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73073
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The `get_board_settings()` function always returns non-NULL, so there is
no need for NULL checks. When only one member is accessed, also drop the
local variable and directly dereference the function's return value.
Change-Id: I4fc62ca2454f4da7c8ade506064a7b0e6ba48749
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75140
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
This mainboard contains in addition to its base variant, mc_ehl2, an LCD
panel driven through the PTN3460 eDP-to-LVDS bridge.
This patch enables the PTN3460 support by adding the device to
devicetree.cb and board-specific configuration parameters in
lcd_panel.c.
BUG=none
TEST=Boot with the LCD panel attached and observe whether the picture is
stable and free of artifacts coming from wrong resolution and timing.
Change-Id: I196d7ceeb7ac241c9b95db2ef791a5f3ff7890a7
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard is based on mc_ehl2. In a first step, it contains a copy
of mc_ehl2 directory with minimum changes. Special adaptations for
mc_ehl5 mainboard will follow in separate commits.
Change-Id: Id80f8eb49dd2fed0ed1ffc479d47d8669eca84c9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Based on touchscreen product spec.
For uldren variants with a touchscreen, drive the enable GPIO high
starting in romstage while holding in reset, then disable the reset
GPIO in ramstage (done in the baseboard).
BUG=b:279989974
TEST=Build and boot to OS in uldren. Touch screen is workable.
Change-Id: Ib1b1ce80aa1dd8c312e3663fc50c9e9f53cc07fe
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74835
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Replace `memupd->FspmConfig.` with `mcfg->` for the sake of brevity.
Change-Id: If2e7cccca955b0c1e07c1ecf100d29a923107856
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75136
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
|
|
This signal isn't functionally being used and is causing leakage
during suspend. Set it to NC.
BUG=b:279762779
TEST=builds. WWAN functional.
Change-Id: I93f2b0a781e250678280b57e4ab1d80ef27ff460
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
If reading the serial/part number fails, returning an empty string is
very confusing. Instead, return "INVALID" to make problems obvious.
Change-Id: I3c174ca76d51b44456c7b68f4fcffb4c8f9379be
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
|
|
The Realtek RTL8111F NIC is currently not defined at all, nor as a child
device, resulting in the on_board flag not being set to 1. This means
that Linux / udev will call the device enp3s0 rather than eno0, as it's
appropriate for on-board ethernet devices.
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Change-Id: I95f01a466a59234d1cbe2420f208bf58ae28fcc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This board has a TPM connector, enable support for it.
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Change-Id: I1861df95eef15bc2bd29412240d61456eaaad8c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75105
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Small typo in brask/gma-mainboards-ads
Should be brask/gma-mainboards.ads
BUG=b:277861633
BRANCH=firmware-brya-14505.B
TEST=Builds
Change-Id: I9800870dcef13a3e16f6235137e79234a5e6bf83
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75052
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Create the gothrax variant of the nissa reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.).
BUG=279614675
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_GOTHRAX
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: I129e4a55e4b87091e425a45392024d04f3977c79
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74748
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
