| Age | Commit message (Collapse) | Author |
|---|
|
This change updates mainboard_init to call
gpio_configure_pads_with_override instead of gpio_configure_pads to
allow variants to provide overrides for the GPIO config table provided
by the baseboard.
BUG=b:111743717
TEST=Verified on phaser that GPIO config with and without this change
is the same.
Change-Id: I494a950100e5ec82504d652ff6e8a75746456d1f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27641
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The next build for phaser swapped the gpio for the touchscreen
enable. In order to support previous builds the devicetree needs
to be updated at runtime based on board revision id.
BUG=b:111808427,b:111743717
TEST=built
Change-Id: I45ef05ea0b991d04d5bf410cd7a175913bf0bf5d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/27638
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The variants of the octopus family have their own schedule and needs
for modifying settings based on the phase of the build schedule while
also needing to maintain support for previous builds. Therefore, utilize
the SoC callback, mainboard_devtree_update(), but just callback into
the newly introduced variant_update_devtree(). The indirection allows
for the ability to move the call around earlier than the
mainboard_devtree_update() if needed while maintaining consistency in
the naming of the variant API.
BUG=b:111808427,b:111743717
TEST=built
Change-Id: If1c2f60cabe65b5f1c6a04dd60e056e50c4993df
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/27637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
The variant_board_id() API was never used on octopus because all
boards in the octopus family used the EC to get board id, i.e. they
all use EC_GOOGLE_CHROMEEC_BOARDID. Therefore, remove the code
and declarations so as not to cause confusion.
BUG=b:111808427,b:111743717
TEST=built
Change-Id: I4f9a24b46dd4262120075d3d42daf22015a3dd50
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/27635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The used super IO is selected in Kconfig depending on the board variant, so use
the selected super IO instead of the board variant directly.
Change-Id: I8421e7c9b1f9ca875c9291f4105c3c20726adfd0
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/27629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Libgfxinit provides a better alternative to the native C init. While libgfxinit
mandates an ada compiler, we want to encourage use of it since it is in much
better shape and is actually maintained.
This way libgfxinit also gets build-tested by Jenkins.
Change-Id: I9228fa7eadfe2a827c1f4de9d6710b60d3f1b121
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Untested but expected to work.
Change-Id: I5a77b7a4343f108f46cf1f97a94e61e88eecb417
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27514
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
MT8183 only allows booting from eMMC, so we have to do eMMC emulation
from an external source, for example EC, which makes the size of
bootblock very important.
A fully functional bootblock (that can boot into verstage or romstage)
is about 38000 bytes. If self decompression (CONFIG_COMPRESS_BOOTBLOCK)
is enabled, only 25088 (66%) bytes are needed.
Inspired from crosreview.com/1070018.
BUG=b:80501386
TEST=manually flashed into kukui and boots into romstage.
Change-Id: I7a739866a4ea3bcafe2ff7b9e88d5ed00f3f3e40
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/27599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
These values are Intel recommended.
IccMax = 28A
DC and AC LL = 4mOhms
Pl2 = 18w
BUG=b:79666828
BRANCH=none
TEST=Enabled p-states with patch
Change-Id:I82d1516998cc26b789faa5d4e897feb06dc06020 and then
"emerge-nocturne depthcharge coreboot chromeos-bootimage", flash spi
image onto nocturne, boot to kernel and verify device stays alive and
responsive for several minutes without locking up.
Change-Id: I4c67c6a095aecc158e529a6b393baf03ec358a3d
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/27175
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables p-states for nocturne which was disabled by commit
de31587a (mb/google/poppy/variants/nocturne: disable p-states). p-states
feature was disabled as a temporary work-around as system was getting
hung while booting up. Now with IMVP7 firmwware turning and hardware
rework the issue is not seen, so its safe to enable p-states.
BUG=b:79666828
BRANCH=none
TEST=cherry picked Change-Id: I4c67c6a095aecc158e529a6b393baf03ec358a3d
patch and then "emerge-nocturne depthcharge coreboot chromeos-bootimage"
, flash spi image onto nocturne, boot to kernel and verify device stays
alive and responsive for several minutes without locking up.
Change-Id: I82d1516998cc26b789faa5d4e897feb06dc06020
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/27257
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For unused pins in octopus baseboard, configure them as GPIO input
and use the default termination. For the pins where board has an
external termination, remove SOC's internal termintation.
BUG=b:110654510
Change-Id: I67ec62913b0ef47105289838218f5d74c004223c
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/27183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
As per the ACPI specification, there are two types of power button
devices:
1. Fixed hardware power button
2. Generic hardware power button
Fixed hardware power button is added by the OSPM if POWER_BUTTON flag
is not set in FADT by the BIOS. This device has its programming model
in PM1x_EVT_BLK. All ACPI compliant OSes are expected to add this
power button device by default if the power button FADT flag is not
set.
On the other hand, generic hardware power button can be used by
platforms if fixed register space cannot be used for the power button
device. In order to support this, power button device object with HID
PNP0C0C is expected to be added to ACPI tables. Additionally,
POWER_BUTTON flag should be set to indicate the presence of control
method for power button.
Chrome EC mainboards implemented the generic hardware power button in
a broken manner i.e. power button object with HID PNP0C0C is added to
ACPI however none of the boards set POWER_BUTTON flag in FADT. This
results in Linux kernel adding both fixed hardware power button as
well as generic hardware power button to the list of devices present
on the system. Though this is mostly harmless, it is logically
incorrect and can confuse any userspace utilities scanning the ACPI
devices.
This change gets rid of the generic hardware power button from all
google mainboards and relies completely on the fixed hardware power
button.
BUG=b:110913245
TEST=Verified that fixed hardware power button still works correctly
on nautilus.
Change-Id: I733e69affc82ed77aa79c5eca6654aaa531476ca
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Logic: If vboot is not used and the tpm is not initialized in the
romstage makes use of the ramstage driver to initialize the TPM
globally without having setup calls in lower SoC level implementations.
* Add TPM driver in ramstage chip init which calls the tpm_setup
function.
* Purge all occurrences of TPM init code and headers.
* Only compile TIS drivers into ramstage except for vboot usage.
* Remove Google Urara/Rotor TPM support because of missing i2c driver
in ramstage.
Change-Id: I7536c9734732aeaa85ccc7916c12eecb9ca26b2e
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/24905
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix VBT SSF setting for panel T8/T10 as Akali/Akali360 panel
has T8 minimum 33.3 ms and T10 minimum of 100 ms.
BUG=b:111530392
BRANCH=nami
TEST=emerge-nami coreboot chromeos-bootimage
Test & measure T8/T10 waveform
Change-Id: I642a1aa0b2d13b33e6113f94e73dfc77834766d4
Signed-off-by: T.H. Lin <t.h_lin@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Coolstar's custom touchpad drivers for Windows require level triggering,
and the Linux drivers don't care/perform identically either way. Set
touchpad interrupt to level trigger, matching change made to other
Chromebooks.
Test: boot Windows 10 on google/chell, verify touchpad functional
Change-Id: Id5f145b8b24c04f9c6661710a0cda95f135293e9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Explicitly enable VMX, as some OSes (eg, Windows) need VMX
feature enabled and locked in order to fully support virtualization
Test: boot Windows 10 on google/chell, verify OS reports virtualization
enabled
Change-Id: I53ff575755a9ca376dbf953db96191c17bf57f5f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add google/asuka (Dell Chromebook 13 3380) as a variant of
glados Skylake reference board:
- add asuka-specific DPTF, EC config, GPIO config, Kconfig,
NHLT config, PEI data, VBT, SPD data, and devicetree
Adapted from Chromium branch firmware-glados-7820.B, commit
b0c3efe54d877246d07f2467b2dff51cc30348fa [soc/intel/skylake: Enable VMX]
Test: build/boot google/asuka, verify correct functionality
Change-Id: I591578fea2514a28c75177835807c3f250904577
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27421
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add google/cave (Asus Chromebook Flip C302SA) as a variant of
glados Skylake reference board:
- add cave-specific DPTF, EC config, GPIO config, Kconfig,
NHLT config, PEI data, VBT, SPD data, and devicetree
Adapted from Chromium branch firmware-glados-7820.B, commit
b0c3efe54d877246d07f2467b2dff51cc30348fa [soc/intel/skylake: Enable VMX]
Test: build/boot google/cave, verify correct functionality
Change-Id: I5c5181ce68f7a24ccd49f53ecd9d48c081fd085a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add google/caroline (Samsung Chromebook Pro) as a variant of
glados Skylake reference board:
- add caroline-specific DPTF, EC config, GPIO config, Kconfig,
NHLT config, PEI data, VBT, SPD data, and devicetree
- add caroline-specific memory-init param to romstage
- adjust mainboard EC SCI events for boards with tablet function
Adapted from Chromium branch firmware-glados-7820.B, commit
b0c3efe54d877246d07f2467b2dff51cc30348fa [soc/intel/skylake: Enable VMX]
Test: build/boot google/caroline, verify correct functionality
Change-Id: I611a4e76581ba2e5b42e1bc48b0a5b8c70f3598e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add google/sentry (Lenovo Thinkpad 13 Chromebook) as a variant of
glados Skylake reference board:
- add sentry-specific DPTF, EC config, GPIO config, Kconfig,
NHLT config, PEI data, VBT, SPD data, and devicetree
- add sentry-specific GPIO determination of which audio codec
is present
Adapted from Chromium branch firmware-glados-7820.B, commit
b0c3efe54d877246d07f2467b2dff51cc30348fa [soc/intel/skylake: Enable VMX]
Test: build/boot google/sentry, verify correct functionality
Change-Id: I783422aedac8b7fc52098eebd05b2061a1011b60
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27418
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Call sleep and wake functions
* Add GBEs for wake
Change-Id: I0cf2cffd06fe2470c2a8f1d8b57de282362ec17e
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/27511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change the I2c timings to the latest measurements.
BUG=b:72442912
TEST=Boot grunt
Change-Id: I6f9538d26b77ae952ad585e569b3a836e1a09da2
Signed-off-by: Matt Wells <dawells@google.com>
Reviewed-on: https://review.coreboot.org/27553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change adds variant rammus derived from baseboard poppy.
The setting is copied from the poppy and will be modified later
BUG=b:111579386
BRANCH=master
TEST=emerge-rammus coreboot
Change-Id: I169c225e28183a7a93f1142a3bf87a60b26ce9ca
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
CONFIG_VGA is only used with C native graphic textmode.
Change-Id: Iafa9e96fd001cd148889ef534e6499f562e7dec6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27530
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable fast or extended DRAM test based on devicetree setting.
The fast DRAM test takes less than a second, while the
extended runs about 1 minute.
Tested on Cavium Soc.
Change-Id: I6a375f3d4c5cea7c3c0cd4592287f3f85dc7d3cf
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/27103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
This change provides implementation of smbios_mainboard_sku
that queries the EC for SKU ID using CBI. Currently,
get_board_sku() is implemented as a common function for all
variants since this is the only way used by all the octopus
variants to query SKU ID. If this changes in the future,
this function can be changed to a variant_* callback.
BUG=b:111671163
TEST=Verified following on phaser:
1. "mosys platform sku" returns the SKU ID programmed in CBI
2. "dmidecode -t 1" shows SKU information as "skuXYZ" where XYZ
is the SKU ID programmed in CBI.
Change-Id: Ic0d344b3c13632f2ca582adc36aa337b99959712
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
This change increases COREBOOT region size by the amount of unused space
left in RO_SECTION. This extra space is useful when building images with
debug enabled.
BUG=b:111661025
Change-Id: Icbd88c3350f96707f37b69fe01f8ae9c7838ab82
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27555
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This board is quite similar to the other ones in this dir an can be
supported with little code changes.
TODO what works:
* DDR2 dual channel PC2-6400;
* SATA;
* USB;
* Ethernet;
* Audio;
* Native graphic init;
* SuperIO Sensors;
* Reboot, poweroff, S3 resume;
* Flashrom (vendor and coreboot);
TODO how tested:
Tests were run with SeaBIOS and Debian stretch, using Linux 4.9.65.
Change-Id: I6844efacaae109cf1e0894201852fddd8043a706
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Both g41c-gs and g41c-s can be supported by the same code since the
only difference is ethernet NIC.
What is tested:
TODO: components
How tested:
TODO: payload + OS
Change-Id: Ib69c2ac0a9dc1b5c46220d2d2d5239edc99b0516
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enable DW9807 NVM support by adding required ACPI code
BUG:b:110815821
TEST=On Nautilus board, execute "cat /sys/bus/i2c/devices/i2c-INT3499:00/eeprom"
in the terminal and see if there is any data to be dumped.
Change-Id: Ib83fa1a522402a59566e3f55fa5c1af4490266e4
Signed-off-by: Alan Chiang <alanx.chiang@intel.com>
Reviewed-on: https://review.coreboot.org/27508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tomasz Figa <tfiga@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
|
|
Nautilus-WiFi board doesn't have external pull-up on USB2_OC2# route,then
abnormal over-current is asserted on USB type-A port.
It causes USB type-A port to be blocked, so we need this internal pull-up.
BUG=b:111578984
BRANCH=poppy
TEST=Verified over-current not triggered abnormally on basic sku board
Change-Id: I159f686cef9c8d254f390d7f1dff8011f43fc066
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Idb65d6c2ec85f09b8e7e9967ba0a055f876378df
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/27521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Convert lars to a variant of glados Skylake reference board:
- add lars-specific DPTF, EC config, GPIO config, Kconfig,
NHLT config, PEI data, VBT, SPD data, and devicetree
- add conditional generation of NHLT ACPI data for Maxim codec,
including override of OEM ID and OEM table ID
- remove existing lars board/directory
Test: build/boot google/lars, verify functionality unchanged
from pre-variant configuration
Change-Id: Iab37f1b92b0f3a5d99796f916a6fdcc14ce4eef4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27413
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Convert chell to a variant of glados Skylake reference board:
- add chell-specific DPTF, EC config, USB port defs, GPIO config,
NHLT config, PEI data, VBT, SPD data, and devicetree
- add romstage handler to turn on keyboard backlight for boards
so equipped
- remove existing chell board/directory
Test: build/boot google/chell, verify functionality unchanged
from pre-variant configuration
Change-Id: I7dfbafe3afcab7cee7bcb2bf91c6733c07b409c4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Convert Skylake reference board glados to variant setup in
preparation for merge with existing Skylake boards chell and lars,
and upstreaming of new boards asuka, caroline, cave, and sentry.
The following changes have been made:
- move DPTF to variant subdir
- move non-common EC defs to variant subdir
- adjust Kconfig for variant setup
- move non-common NHLT config to variant Kconfig
- make non-common NHLT ACPI code conditional
- move devicetree to variant subdir
- move board GPIO defs to variant subdir
- move board PEI data to variant subdir
- move SPD index calculation to romstage so available for
dual-channel determination during PEI for boards which need it
- move SPD compilation to variant makefile
- add weak function for determination of dual-channel RAM
- add weak function for mainboard_gpio_smi_sleep() so SKL-Y variants
can override and power down rails as needed
Test: build google/glados
Change-Id: I41615979dc11b5a10e32d6b5f477a256735cde53
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable the GEO SAR feature for nocturne. OxM programs wifi_sar VPD key in factory.
coreboot reads the VPD and creates the ACPI table as per the WGDS spec.
BUG=b:65155728
BRANCH=none
TEST= Set the wifi_sar VPD with below command (values are junk for test purpose only,
actual values would be set be OxM)
sudo vpd -f <coreboot.rom> -s wifi_sar=30313233343536373839303132333435363738393030313
24142433435364445463031324142433400364445463031323343444546303132333435
Flash the <coreboot.rom> and boot to kernel. Get ACPI table and WGDS would get created
with VPD values passed in.
Change-Id: I32ad591f15fdb34704c8d98d98646dfa2d8882ff
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/27501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Refactor GPIO code which will be reused among similar SOCs.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Elm
Change-Id: Icdd1f2a1dd1bd64a7218bf9c63bd4a0af1acbcc0
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Latest nocturne architecture uses clk src 3 for nvme.
BUG=b:111514174
BRANCH=none
TEST="emerge-nocturne coreboot chromeos-bootimage" and verify nvme
nocturne devices are able to recognize the nvme controller.
Change-Id: I5b2bf012ba88568cb4b0bb3918a3a2c6770ff4c1
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27536
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is based on the Grunt variant.
BUG=b:111607004
TEST=Build Liara
Change-Id: I8f23e972be0d1665c736d61621a0caaa4c4c5551
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This is based on the Grunt variant.
BUG=b:111606874
TEST=Build Aleena
Change-Id: I6fd42db6f9f309c3c375b670cd22f818555e4195
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Implement ACPI S3 resume control to restore the state before entering
sleep.
* Store the requested state wake state for bluetooth and WWAN.
* Add new methods to init the state and apply the requested state on wake.
* Call the new method on all devices.
Change-Id: I13c08b8c6b1bf0f3deb25a464b26880d8469c005
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/22377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Tested on LVDS (internal), VGA and HDMI (on the dock DP++ connector) output with
both native resolution and textmode.
Change-Id: Ibfcb586d7b4cac7f1d22540bb96c288704a277a0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27513
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Add support for secure/unsecure split
* Use MMCONF to access devices in domain0
* Program MSIX vectors to fix a crash in GNU/Linux
Tested on Cavium CN81XX_EVB.
All PCI devices are visible.
Change-Id: I881f38a26a165e6bd965fcd73547473b5e32d4b0
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25750
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for SMBIOS table 'IPMI Device Information' and use it on
HP Compaq 8200 Elite SFF.
Tested on HP Compaq 8200. dmidecode prints the table and sensors-detect scans
for IPMI compatible devices.
Change-Id: I66b4c4658da9d44941430d8040384d022d76f51e
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/25386
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Observed thermal shutdown initiated by DPTF due to CPU temperature
reaching critical temperature trip value. During stress testing with
busty workloads like Octane, Aquarium on open yorp board with heat sink,
sometime CPU temperature spikes till 99 degree Celsius and DPTF
initiates system shutdown. With reference to previous APL/reef/coral
platforms, this updates 105 degree Celsius for the CPU critical
temperature trip value to avoid shutdown. This patch also updates power
limit1 value to avoid the abrupt thermal shutdown by DPTF.
BUG=b:79779737
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: Icd786d3c9b5f7c733dac3fd3e22579e2434058a6
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/27294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Put the PCIe clock pins in power-saving mode for the WiFi module to save
power.
Note: This currently does not appear to have any effect on grunt.
BUG=b:110041917
BRANCH=none
TEST=boot without this patch:
$ iotools mem_read32 0xfed80e00
0x0046f3ff
With this patch:
$ iotools mem_read32 0xfed80e00
0x0046f3f1
Change-Id: I389815bc36b8610a30b0cbb9d73262ad392e0181
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
We should use active-state power management where possible to reduce
power consumption during normal operation. Enable these options.
Linux does not seem to enable this for AMD, and the Intel code in coreboot
does enable these options.
PCIEXP_COMMON_CLOCK is enabled also, to follow how Intel does it.
BUG=b:110041917
TEST=boot on grunt, see that WiFi and eMMC still run OK
Change-Id: Ia7c711304ffe460a9fb0d4f654a51485958239ea
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27464
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This creates a meep variant for octopus.
The devicetree overrides are copied from yorp, otherwise everything
just defaults to baseboard settings.
BUG=b:111543000
TEST=None
Change-Id: I791f8d1589d7323fbe884dddf0f9d7362a41b9ac
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/27516
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Extracted from live running Thinkpad X201 with vendor firmware.
Change-Id: Ia33b4c1a2af6f7d460375cc8ea4e404963a72244
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Extracted from the stock UEFI using UEFItool & intelvbttool.
Without it, the kernel complains about the missing VBT table.
Additionally, the invalid oprom signature warning given by i915
is also gone.
Change-Id: I1871eca9e9c21531d842289f6624ec44420d9844
Signed-off-by: Pablo Moyano <42.pablo.ms@gmail.com>
Reviewed-on: https://review.coreboot.org/27482
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Atlas has one sensor, create a single endpoint to CIO2. Create power
resource for enabling/disabling camera.
BUG=b:111141128
Branch=None
TEST=Testing on Atlas board
Change-Id: Ide0e923bbc34f869dd0227c0a29977645bc5d58d
Signed-off-by: Ping-Chung Chen <ping-chung.chen@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/27350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
|
|
* Fix CID1393963 (Uninitialized variables)
* Comment in working code
* Remove workaround to limit DDR speed
Change-Id: I96289da43c1018c2fdf9d013ce7f21d7511ba595
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/27452
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Keep the backlight off until it is needed.
BUG=b:72694972
TEST=Backlight turns on at ChromeOS splash screen, not prior.
Change-Id: Ia1aba787734e2976146ecd305dd821f0b326f0db
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
BUG=b:72694972
TEST=Backlight turns on ChromeOS resume
Change-Id: I452e2ea94b508b137cf52301df5d2d1ad5c9ab70
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27488
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable the backlight in the OS callback to SMI for APMC. This keeps
the backlight off until the OS is ready to display something.
BUG=b:72694972
TEST=Backlight turns on at ChromeOS splash screen
Change-Id: Idf32b1a3d45971883571a829a5c0c1f8563bb1f7
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add the mainboard resume function and __weak variant override.
Change-Id: I808734208bd1ce81428771ea203709b53db56cd3
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This updates the IDPROM region along with the unused regions.
Change-Id: If73bb8162d3d0733e3bd8561cd5549f2184db2be
Signed-off-by: David Hendricks <dhendricks@fb.com>
Reviewed-on: https://review.coreboot.org/27505
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move the EC under the LPC PCI device to make sure that the SSDT path
matches the DSDT. Matches the behaviour of all other Lenovo devices.
Change-Id: I9ded7f639866d71d39ea0d5d0c36602d386c177f
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/27481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Matthias Gazzari <mail@qtux.eu>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
there are 3 thermal sensors and index is:
0: 1 Charger
1: 1 SOC
2: 0 CPU
it needs to adjust sensor to index 2 to have correct
CPU temperature.
BUG=b:111284412
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I27afb6c5b64b0c39d6db15e6c61ea16a1fda1ca3
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This device claims to run at 75MHz with dual read, but it is not always
reliable. Add an option to change the SPI flash speed to 16MHz, to avoid
any problems.
BUG=b:111363976
TEST=manually try to get my em100 running (it doesn't yet)
Change-Id: I78d3d32c467aac82c72d31c773bfb0f69808aed4
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27466
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This applied to AMD devices as well as Intel, although the mechanism is
different. Move the option to a common place.
BUG=b:111363976
TEST=USE=em100-mode emerge-reef coreboot
See that a message appears:
* Enabling em100 mode (slow SPI flash)
Change-Id: Iea437bdf42e7bc49b1d28c812bfc6128e3eb68bd
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add new Pantheon sku-id for loading vbt-pantheon.bin
BUG=b:78663963
BRANCH=firmware-nami-10775.B
TEST=Boots to OS and display comes up.
Check the board specific vbt binary loaded.
Change-Id: I1ee156372754ac0e77caae5959a9ca9884de95f4
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27432
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:111195311
TEST=Build grunt, verify SPDs are present
Change-Id: Ief5ed5c3ca1d96b36926f1fc84c344a8d66dcda5
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/27437
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The FCAM_PWR_EN gpio should be GPP_B4 according to the latest board
schematics.
Change-Id: Id926bd224b3392d8a61b6d8ae0509053afaa5b9e
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Reviewed-on: https://review.coreboot.org/27433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tomasz Figa <tfiga@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Currently thermal event support can not be disabled at board level.
Define and dependent code are placed in same file.
Move define of HAVE_THERM_EVENT_HANDLER to mainboard file.
Change-Id: Icb532e5bc7fd171ee2921f9a4b9b2150ba9f05c5
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/27415
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables tablet mode ACPI device for yorp.
BUG=b:111264961
CQ-DEPEND=CL:1132686
Change-Id: I81140b84a1adb5b21f1656fd89d953331e538f01
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Enabling of TBMC device on AP side requires corresponding support on the
EC side as well. Since not all octopus variants have tablet mode support
enabled, this change enables TBMC device only for phaser.
BUG=b:111264961
Change-Id: I1ce181baa8ebaff0a9d767e97ddc256eef9789e8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
This change enables EC SW sync for bip by removing GBB flag selection
for disabling SW sync.
BUG=b:110523189
TEST=Verified that EC SW sync works fine on bip.
Change-Id: Iff8ee67fd682530a4fa82643cd1d00a645b347a3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Remove "IshEnable" from soc_intel_skylake_config since it's not
used anymore.
Enable/disable ISH by checking if ISH device is turned on or not.
Refer to https://review.coreboot.org/#/c/coreboot/+/26485/.
BUG=b:79244403
BRANCH=none
TEST=Built.
Change-Id: I4d2889af118659852431c87cb516fd19b577efc5
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
To enable ISH device on atlas board, change "device pci 13.0 off end" to
"device pci 13.0 on end" in file
mainboard/google/poppy/variants/atlas/devicetree.cb. "IshEnable" is
not needed.
Config atlas board specific ISH setting in devicetree.cb.
Dynamically load gpio setting for ISH enabled/disabled cases.
BUG=b:79244403
BRANCH=none
TEST=Verified on Atlas board with ISH rework. ISH log showed on console.
Change-Id: I8269a85cd2ab7917bfc0e7d63d988e0e678d0bf2
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In order to get better performance, map dram as cached after dram ready
in romstage.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui. Need a futher check after dram
calibration code ready.
Change-Id: Ie541fe08ee1d5b260abbabc0a5c18fb04e602b9c
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27304
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Refactor MMU operation code which will be reused among similar SOCs.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Elm
Change-Id: Id8173da0a02e57e863263fcd89c91a9c089e8a0f
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add an extra space after 8th value on each line to make it easier
to count the values.
Update the empty spd to remove two random 0x80 values.
BUG=None
TEST=None
Change-Id: If330dbf0c133f65aedddc58ecb351a80b0e45a05
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/27423
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:111079089, b:80375243
TEST=Build grunt, verify that SPDs are included.
Change-Id: Idb03a3fa0842f7f89bb8c66dedbb8a0b293569be
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/27422
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I07428161615bcd3d03a3eea0df2dd813e08c8f66
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Set cntfrq_el0 to provide correct timer frequency.
Change-Id: I4b6d0b0cf646a066fc5a51552a1891eccbd91e5e
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25450
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Print some useful information about the board.
Change-Id: I0acac7a29290bc2eb9f4283317165fa0cf1b24e1
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25449
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Only init UART_FOR_CONSOLE
* Allow UART init with zero baudrate.
* Init UART0..3 on Cavium's cn8100_sff_evb to fix kernel panic.
Tested on CN8100_SFF_EVB.
Change-Id: I1043b30318ec6210e2dd6b7ac313a41171d37f55
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
* Configure and enable MMU.
* Cover the whole I/O space.
* A minimum of 512KB TTB space is required.
* Use secure mem attribute as firmware is running in ARM TZ region.
Tested on Cavium SoC.
Change-Id: I969446da62b4cc7adf9393fab69ff84ebf49220d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
This adds Cavium CN81xx SoC and SFF EVB files.
Code is based off of Cavium's Octeon-TX SDK:
https://github.com/Cavium-Open-Source-Distributions/OCTEON-TX-SDK
BDK coreboot differences:
bootblock:
- Get rid of BDK header
- Add Kconfig for link address
- Move CAR setup code into assembly
- Move unaligned memory access enable into assembly
- Implement custom bootblock entry function
- Add CLIB and CSIB blobs
romstage:
- Use minimal DRAM init only
devicetree:
- Convert FTD to static C file containing key value pairs
Tested on CN81xx:
- Boots to payload
- Tested with GNU/Linux 4.16.3
- All hardware is usable (after applying additional commits)
Implemented in future commits:
- Vboot integration
- MMU suuport
- L2 Cache handling
- ATF from external repo
- Devicetree patching
- Extended DRAM testing
- UART init
Not working:
- Booting a payload
- Booting upstream ATF
TODO:
- Configuration straps
Change-Id: I47b4412d29203b45aee49bfa026c1d86ef7ce688
Signed-off-by: David Hendricks <dhendricks@fb.com>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/23037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Change-Id: Iedc2e48349e40e94863c8080d11e11dbe6084c9d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
These two files were added before I was able to get the updated linter
committed. Updated/Add the headers so the stable header lint check
can be updated.
Change-Id: I464ddecb5eebe8c5b907f3dcfeab1b06501af6ab
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
change I2C irq to EDGE trigger
BUG=b:110962003
BRANCH=master
TEST=emerge-grunt coreboot
Raydium TS is working.
Change-Id: Iff3acf4199d23b29dff209ec1c03a731679c6cbe
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27327
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change configures ACPI to properly route notifications from the EC
for tablet mode events to userspace. Relevant EC config changes are at:
https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/1125261
BUG=b:111078678
TEST=With EC change, tablet mode detected by evtest and powerd
Change-Id: Ifbc318186b195534f647f062544de4968aa87401
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/27346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
the FPMCU_INT_L on GPP_C11 is active low but the kernel irq handler is
defined as IRQF_TRIGGER_LOW, so do not invert it twice.
BRANCH=poppy
BUG=b:78613978
TEST=On Nocturne, the 'cros_ec' IRQ count in /proc/interrupts does not
increment wildly.
Change-Id: I56c13c797b133dd22669a2299bcd16ef14eed335
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/27221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I3bdb93e51cabbfc14fe992ccdb6556e344e03c2f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27345
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: Iee237206f309409be64307d2daee044da52a05e1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I85cd567a923cccd2504f351aae276b5f0d9db4de
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/27347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt Delco <delco@google.com>
Reviewed-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Clean up leftovers of old SPD generation and utilize
common procedure to produce SPD binary.
Change-Id: I4e48817c03b4372887bc0ea14209736ae2b4e48f
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/27301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I0df578b98c5b346caa6f6df5fdabda28788e6b66
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Ia658c117434c3fae45bbbe6c472ca58ba4f1a117
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Until now, chromeec was doing keyboard initialization for the boards
that have DRIVERS_PS2_KEYBOARD selected. However, coreboot does not
leave the keyboard controller in a default reset state. This could
result in payloads or OS failing to probe the controller as there
could be stale data buffered in the controller during the handoff.
Since the boards using chromeec already perform keyboard
initialization in payload, there is no need to initialize the
keyboard in coreboot too. This change gets rid of DRIVERS_PS2_KEYBOARD
selection from all google mainboards using chromeec.
BUG=b:110024487
Change-Id: I9af48e648231c18f98d0cc1ddd178b8d00082b0a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Until now, chromeec was doing keyboard initialization for the boards
that have DRIVERS_PS2_KEYBOARD selected. However, coreboot does not
leave the keyboard controller in a default reset state. This could
result in payloads or OS failing to probe the controller as there
could be stale data buffered in the controller during the handoff.
Since the boards using chromeec already perform keyboard
initialization in payload, there is no need to initialize the keyboard
in coreboot too. This change gets rid of DRIVERS_PS2_KEYBOARD
selection from all google mainboards using chromeec.
BUG=b:110024487
TEST=Keyboard works fine after booting to OS even if user hits keys
during BIOS to OS handoff.
Change-Id: I1f49b060eb005c0f2b86f9d68d6758954eeb3cf0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27291
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3873cc8ff82cb043e4867a6fe8c1f253ab18714a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Also remove some unnedded includes.
Change-Id: I036208a111d009620d8354fa9c97688eb4e872ad
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
To uniform the naming of the 'Dual Graphics' mode amongst the ThinkPads that
support it, the T400 CMOS value needs a change. This was the outcome of a
discussion on another patch: https://review.coreboot.org/#/c/coreboot/+/23040/
This might cause breakage for automated NVRAM configuration scripts, and
manuals. I only found one manual using the previous 'Switchable' option:
https://libreboot.org/docs/install/r400_external.html#a-note-about-gpus
Change-Id: I2e4d8bafbae5de97c78dab118f75fdefff1d7c37
Signed-off-by: Nico Rikken <nico@nicorikken.eu>
Reviewed-on: https://review.coreboot.org/27158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Enable Image Processing Unit and CIO2 device that constitute IPU3.
BUG=None
TEST=Build and boot up into Nocturne platform and check with lspci.
Change-Id: Ic2edf5ec7bde5c55ce1b13cf7b680094a9fffc6a
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/27124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
To make image sensor working, the intended power sequence need to
applied.
BUG=NONE
TEST=NONE
Change-Id: I4833c0e303174b297c1d193495e08e55d294a717
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/27094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Sensors and CSI2 receiver configuration for Nocturne platform.
IMX355 module has VCM, NVM and is on the second port of receiver.
IMX319 module has NVM and is on the first port of receiver.
Change-Id: I37c877df8062d5c79e25ed27775ab58e977555db
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/26283
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These bits start the acquisition process. They should only be set by the
driver.
BUG=b:74363445
TEST=compile
Change-Id: I9e10f5570ac82124f7f4b5cc7aaad27da0c578be
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/27265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
