Age | Commit message (Collapse) | Author |
|
Update common files and add files for grunt to the variant directory.
BUG=b:68293392
TEST=Build only
Change-Id: I7b80e470058872d6613e66e64c8dd1494942e9b9
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=b:68293392
TEST=Build only
Change-Id: Ie4d039b4da10a992fc9dd2b0221fd4a1644aae6a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22373
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Stoney Ridge ASL uses global NVS for sharing data between ACPI and SMM.
Change-Id: I8f497870844da1f56ff5c3b126d5613be36a9bfb
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Several SPD hex files for chell were missing from upstream coreboot
(as compared to the Chromium tree/branch), which resulted in the
incorrect type and amount of RAM being reported on chell boards
with > 4GB RAM. Add these missing files and their Makefile entries.
TEST: boot google/chell m7/16GB config and observe correct RAM
type and amount reported via dmidecode and cbmem console log.
Change-Id: I37d708c96e754b438e40fc413420aa64bf234c29
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22402
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set the UMA memory size to 128 MiB. This value was empirically tested
by AMD as the lowest value one could use.
BUG=b:64927639
TEST=default, and 64, 128, 256, 384MB non-legacy configurations.
Change-Id: I2bc808d8b402c3eb16a1a5962f3fa9d6b224cf52
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/21335
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a #define for MB_DIMM_SLOTS and verify it doesn't exceed the max
supported for the device. AGESA's DRAM procedures follow the BKDG and
may vary depending on the number of slots on the motherboard. DIMM
numbering and ordering is also affected by this value.
Replace hardcoded integers with defined values for DIMM slots and
number of channels.
Change-Id: I4f7336da80b4e3d7f351502a63de0652e9ff5395
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/21853
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Kahlee needs to keep its DRAM contents after a reset. Move this
override out of the OemCustomize.c file to a devicetree register
setting.
Change-Id: I3196cb8b94bec64e8ce59e4285cf8d97f442bd3d
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/21858
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On Astronaunt, after the system enters the S5 power state, there is a
10-second timeout before the system transitions the power state from S5
to G3. The EN_PP3300_DX_LTE_SOC signal, which is controlled by GPIO_78
on the APL platform, remains on during that period. If the system is
powered back on before going to G3, the built-in modem won't go through
a power cycle as EN_PP3300_DX_LTE_SOC is never de-asserted.
Keeping the modem, and indirectly the SIM, powered during a quick system
power cycle may sometimes be undesirable. For instance, we would like a
SIM with PIN lock enabled to require unlocking each time the system is
powered on. After the SIM receives a PIN, it may remain unlocked until
its next power cycle.
Also, it is often desirable to power cycle the modem when the system
goes through a power cycle. For instance, a user may power cycle the
system to recover a wedged modem.
BUG=b:68365029
TEST=Tested the following on an Astronaunt device:
1. Verify that the modem is powered on after the system boots from cold.
2. Suspend the system to S0ix. Verify that the modem remains powered on
when the system is in S0ix. After the system goes back to S0, verify
that the SIM with PIN lock enabled doesn't request unlocking, and the
modem can quickly reconnect to a network.
3. Configure the system to suspend to S3 instead of S0ix, and then
repeat (2).
4. Perform a quick system power cycle, verify that the modem is powered
cycle and the SIM with PIN lock enabled requests unlocking.
Change-Id: Ie60776d5d9ebc6a69aa9e360bd882f455265dfa2
Signed-off-by: Ben Chan <benchan@chromium.org>
Reviewed-on: https://review.coreboot.org/22415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add dptf.asl (copied from reef) to baseboard variant includes,
instruct zoombini variant to use the baseboard's dptf.asl,
instruct zoombini variant to use the baseboard's gpio.h.
BUG=b:64395641
BRANCH=None
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x
-a" compiles successfully.
Change-Id: I9aa37f5afc35dab372917a4c84ff3121ec569546
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/22381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change EC_SCI_GPI to GPE0_ESPI.
BUG=b:69011806
BRANCH=master
TEST=none
Change-Id: I5d07bc0ef295d776635ff3a585c8de9028bd3f6a
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/22380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Poppy and variants won't be using deep S3. This change disables deep
S3 option in devicetree.
BUG=b:69053636
Change-Id: I5fb4a6a0e4216a3648b5ed888f6dc6618f1a9fc4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22378
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch enables customized NIC leds as follows:
Green Orange (Amber)
100M off blinking
1000M on blinking
BUG=b:65437780, b:68284778
TEST=Make sure the registers are programmed as expected and observe the
LEDs are behaving as expected. Perform suspend/resume test and the
LEDs are still working as expected.
Change-Id: I9bb1367a4c742c2755d620e14ee6dfe70ee7f34b
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This compares to the acpi directory in other variants.
BUG=b:68293392
TEST=Build and boot kahlee
Change-Id: I05d402995b280d6f020bc2575063dbffefa30670
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Even though this GPIO isn't used for Kahlee, it needs to be defined
so that the weak version of the variant_board_id() function can
compile.
BUG=b:68293392
TEST=Build and boot kahlee
Change-Id: Ia8daf70fbafe02ec37c6b5eb8421cdb11de3be8b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Now that recovery button has been enabled through cr50,
we can add VBOOT_PHYSICAL_REC_SWITCH config and treat
the recovery button like on any other chromebox.
BUG=b:37751915, b:63893483
BRANCH=None
TEST=With DUT in normal mode, boot into recovery, press ctrl+d
followed by pressing the recovery button. Should successfully
boot into dev mode.
CQ-DEPEND=CL:737477
Change-Id: I72fb42508083295e317dd06900796dc0cda753f6
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22368
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable Dialog DA7219 codec i2c device and add required SSDT parameters
BUG=b:68686020
TEST=With req'd driver support in kernel v4.4 verify audio on headset
Change-Id: Ic815c929f29bec0d26a2981e9933b752c2d84c70
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Shruthi Sudhakar <shruthi.sudhakar@intel.com>
Reviewed-on: https://review.coreboot.org/22264
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Nautilus board uses Dialog da7219 headset codec,
Select the appropriate NHLT blob to be packaged in CBFS.
Also generate the required ACPI NHLT table for codec
and the supported topology in nautilus.
Removes unwanted DMIC blob pick for nautilus
BUG=b:68686020
TEST=With the required driver support in kernel verify that
the Audio plays on headset and recording on headset mic
Change-Id: I104889f54da1de38854bcb72aabbc88b739d6c09
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/22325
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since we move from cannonlake U DDR 4 platform to cannonlake U LPDDR4
platform, it is also critical to revisit the GPIO settings as they are
different. Remove unused GPIO setting for old platform, and clean up the
native function definition. PAD_CFG_NF can only select NF1,NF2 ..., set
to GPIO mode is illegal.
TEST=Boot up in chromeos successfully.
Change-Id: I0022b791bd8459ea2afdcd0241b603ce81408785
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/22326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
SCI trigger logic had to be inverted.
This patch enables the system to wake up from S3 when lid is opened
when the system is in suspend state.We are trying to match what a
external EC card running ChromeEC FW is sending on the signal.
TEST = Verified that system wakes up from S3 on toggling lid switch
back to open state.
Change-Id: Ib42a38088ee028eddc6769921b0552c569da25a9
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Schander <coreboot@mimoja.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=b:68865273
Change-Id: Ia2e9b10035e9dd502a563cdf8324ea8ea1922db3
Signed-off-by: Lann Martin <lannm@chromium.org>
Reviewed-on: https://review.coreboot.org/22359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
For internal measurements this mainboard needs a marking inside the NC
FPGA when coreboot is ready and payload has been loaded.
Change-Id: I37908b21e2a077dec7fa99b0db6d1fd9b6878341
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ifc3423ff983fb631edcab087d04742937b25ef86
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/22310
Reviewed-by: FEI WANG <wangfei.jimei@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
RISC-V is moving towards OpenFirmware-derived device trees, and the old
functions to read the config string don't work anymore. Use dummy values
for the memory base and size until we can query the device tree.
Change-Id: Ice13feae4da2085ee56bac4ac2864268da18d8fe
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On older Grus, GPIO0_A2 was an audio voltage rail enable line. On
Scarlet, we instead moved the audio codec enable (previously on
GPIO1_A2) there. Unfortunately the code still had some hardcoded
leftovers that were overlooked in the initial port and make our speakers
smell weird.
This patch fixes the incorrect GPIO settings and adds the speaker enable
pin to the GPIOs passed through the coreboot table, so that depthcharge
doesn't have to keep its own definition of the pin which may go out of
sync.
Change-Id: I1ac70ee47ebf04b8b92ff17a46cbf5d839421a61
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
Reviewed-by: Alexandru Stan <amstan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Enable USB2 port 10 for CNVi bluetooth.
TEST=Boot to OS, verify bluetooth functionality.
Change-Id: I5f2390c149bf0de911efac09f54ccd641f51bbcd
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/22290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
|
|
Current VBT setting for T8 is only 1ms which is under Innolux
N116BCA-EA1 panel's spec.
Modify T8 to 100ms.
(Innolux's panel's spec requires T8 needs to be greater than 80ms)
CQ-DEPEND=CL:*496012
BUG=b:67756548
BRANCH=master
TEST=emerge-coral depthcharge coreboot chromeos-bootimage
Run on DUT and check panel sequence meets spec.
Change-Id: I580567decfccd78366c37181255015ac2cd76493
Signed-off-by: Ren Kuo <Ren.Kuo@quantatw.com>
Reviewed-on: https://review.coreboot.org/22306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quantatw.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
From what I can tell FILECODE isn't used at all in this file.
Remove it.
Change-Id: Ie88140e63a4917f470f42119c1fe4e8c7d2584ca
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: I513b26d39973d9714b531d1ab0755c66d19eb332
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I0bf4d6318ade6e931db4f8b1af08db1f9f93c313
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/22228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Set SCS SD enable FSP parameter and set card detect
gpio information.
Change-Id: Ic99466c0d2d59070418d765442ff6d217023803b
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/21603
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In skylake based platforms, setting GPIO pad reset config
to DEEP will reset the gpio configuration across warm reset,
set it to RSMRST to preserve the configuration across warm resets.
Also, moving the configuration from early to late as appropriate.
BUG=b:64386481
BRANCH=none
TEST= WiFi functionality across S3, DeepS3, S0ix and warm/cold reboot.
Change-Id: I38940b7c7d71e60bf0e51d6978a00be148ad61bc
Signed-off-by: Divya Chellap <divya.chellappa@intel.com>
Reviewed-on: https://review.coreboot.org/22174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Adapted from Chromium commit 12ad5b5: Reks : override USB2 Phy settings...
Base on Intel recommendation, override following
settings for USB2 port 1/2/3 on BSW D-stepping SOC.
1. Set USB[1] register for right side to 7321
2. Set USB[2] register for left side to 7021
3. Set USB[3] register for CCD to 7021
Original-Change-Id: I04240a010e875f29c47f4fea83ff918f180b0273
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Keith Tzeng <keith.tzeng@quantatw.com>
Change-Id: Iabd6312576e9897315c4e4dbf19341380d9d1414
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Adapted from Chromium commit 6ee6f3d: Reks: To set the RX ODT limit...
Override RX ODT and DRAM geometry for Micron part MT52L256M32D1PF-107.
Use get_ramid() to determine if override is necessary.
Original-Change-Id: I41f3aba030a00152e1217533ef953338ac396605
Original-Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Original-Reviewed-by: Kane Chen <kane.chen@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Keith Tzeng <keith.tzeng@quantatw.com>
Change-Id: Iea8c3c67e5afb21285dc15ad665474ad5f192423
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
ASL+ Optimizing Compiler/Disassembler version 20170831 shows the remark
below.
```
dsdt.aml 87: Method (_CRS, 0x0, NotSerialized)
Remark 2120 - ^ Control Method should be made Serialized \
(due to creation of named objects within)
```
So, serialize the method.
Fixes: commit 4a51ea8470 (google/kahlee: Add ASL for Elan touchpad)
Change-Id: I664f493318cbfd80d91565c0d29ec918278c4906
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/21901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Move files that are particularly specific to the mainboard into the
variant directory. Files that only have small areas of mainboard
specific pieces use #if to separate between the boards.
Add memory.c to split out the variant board id into a weak function.
Add baseboard/gpio.h to satisfy the build - this will be updated in the
next commit.
BUG=b:68293392
Change-Id: I7c1beb45f571f2547f3b5b0d7ec78923d0cec761
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The default setting for I2Cx is 400kHz. On this mainboard there is a
device on I2C0 which requires a lower clock rate to work correctly. For
this reason we set the frequency to 100kHz.
Change-Id: I637a58a0c89ead55ca1176d6aecdfaba5897d64f
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This mainboard has its own coreboot ready LED. The LED is switched on
via GPIO CNV_RGI_DT.
Change-Id: I179d013746c1334337dc9e6b7f09ac54eff0cd77
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
On this mainboard there are PCI devices, which are connected to the PCIe
root port via a PCIe-2-PCI bridge. One of the devices only supports
legacy interrupt routing. For this reason we have to adjust the PIR6
register (0x314c) which is responsible for PCIe device 13h and 14h. This
means that the interrupt routing will also be the same for both PCIe
devices. The bridge is connected to PCIe root port 4 (Device 14.0).
The following routing is required:
INTA#->PIRQB#, INTB#->PIRQC#, INTC#->PIRQD#, INTD#->PIRQA#
Change-Id: I5464c9a2669773bc1e6cd4b4d29d1be838dbfa27
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
add elan touchpad in devicetree.
BRANCH=master
BUG=b:66462881
TEST=emerge-nautilus coreboot
Change-Id: I30e6797ef06351690ff0b5c78ea76918547167a7
Signed-off-by: Chris Wang <chriswang@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/22187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: shkim <sh_.kim@samsung.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update GPIO settings to meet nautilus's schematic design.
BRANCH=master
BUG=b:66462881
TEST=emerge-nautilus coreboot
Change-Id: I11930df62130431764702371a3ba84949a65ba30
Signed-off-by: Chris Wang <chriswang@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/22183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: shkim <sh_.kim@samsung.com>
|
|
update with nautilus memory spds.
RAM_ID = 0 => K4E8E324EB-EGCF
RAM_ID = 1 => K4E6E304EB-EGCF
RAM_ID = 2 => K4EBE304EB-EGCG
BRANCH=master
BUG=b:66462881
TEST=emerge-nautilus coreboot
Change-Id: I29d8a76b170aee64bb0125276df0e4709012daba
Signed-off-by: Chris Wang <chriswang@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/22175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: shkim <sh_.kim@samsung.com>
|
|
Current VBT setting for T8 is only 1ms which is under Innolux N116BCA-EA1
panel's spec.
Modify T8 to 100ms.
(Innolux's panel's spec requires T8 needs to be greater than 80ms)
BUG=b:67756548
BRANCH=master
TEST=emerge-coral depthcharge coreboot chromeos-bootimage
Run on DUT and check panel sequence meets spec.
CQ-DEPEND=CL:*493633
Change-Id: I7934b0f6d40b15796c55d360995c5eb0c5049222
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/22294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Leaving the wifi related gpios unmodified for now
due to FSP problem. If H0-H3 is configured as native mode
and GPIORXDIS, GPIOTXDIS bits in DW0 are cleared, it causes
FSP to assert when wifi module is attached. coreboot gpio
macros clears these 2 bits because they are suppose to be
"don't care" in native mode.
TEST=Boot to OS and verify wifi
Change-Id: Ica5e1c43802d04a9471cdfa0087e86f669122fff
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/22094
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is to enable SPD word access to reduce boot time. It can save
80 ~ 100 ms per DIMM.
BUG=b:67021853
BRANCH=None
TEST=system boot, and boot time is reduced
Change-Id: Ic527a539ed634e15b939b18fff4b4e08ebb3ec57
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/22267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
For Raydium, export reset GPIO as well as PowerResource.
Let EN_PP3300_TOUCHSCREEN signal will goes to low at S3 mode.
BUG=b:67879912
BRANCH=coral
TEST=emerge-coral coreboot
Change-Id: Ibf501b40ecfc957fd8be7ebffd2357dfa0e07757
Signed-off-by: Pan Sheng-Liang <Sheng-Liang.Pan@quantatw.com>
Reviewed-on: https://review.coreboot.org/22252
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For MELFAS/Raydium, export reset GPIO as well as PowerResource
BUG=b:68141940
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: I1915ff8207502b80ecba6b63ce2ce1b866faf4c4
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22146
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ia21a3e93712bd6b6780fe7308c6cf79c553f4e1b
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There's no need to have these separated.
BUG=b:64932381
Test=Build & Boot
Change-Id: I22898d3bf95d5e9a8fc2643bfccae1e2f5b29e44
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add new board librem15v3 as a variant of the librem_skl baseboard.
Changes from the librem13v2:
- Change board name and version
- Change GPIO A18, A19, A20, D9, D10 and D11 from NC to GPIO
- Enable PCI device 1c.4
- Change USB port definitions in devicetree
TEST: build w/SeaBIOS, boot PureOS on Librem 15 v3 hardware
Change-Id: I7c762a34f5b961c908e4a29ec331da4b0dea9986
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22048
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Convert the Purism Librem13v2 board to a variant setup,
in preparation of adding the librem15v3 as a new variant.
The 13v2 and 15v3 are nearly identical, so this minimizes new
code to add support for the latter.
Change-Id: I5d648cdb8f63c03de5474253203b3d0853673294
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22047
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch refers to variant_gpio_table for board gpio configuration.
Change-Id: If5b4c20ceccb32fc1ab4246482d8fecb491777c4
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/22129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
It seems that recent changes in coreboot have fixed the raminit issues
on this board; the workaround of 10 ms delay after the S3 resume is not
needed anymore and can be removed.
Change-Id: If8fb97ecf3eb797f53270a053201fafd32031678
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/21485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Migrate the Librem13v2 from using FSP 1.1 to
the public/GitHub FSP 2.0 Skylake/Kabylake release:
- select FSP 2.0 in Kconfig
- adjust romstage/ramstage functions as required
- refactor pei_data functions
- remove VR_RING domain from devicetree (unsupported in FSP 2.0)
- add SataSpeedLimit parameter to work around power-related issue
when operating at SATA 6.0Gbps speed
TEST: build/boot Librem13v2, observe successful boot, lack of
SATA-related errors in dmesg.
Change-Id: Iedcc18d7279409ccd36deb0001567b0aa5197adf
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22046
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
In order to pass type C USB2 eye diagram for sku Astronaut,
USB2 port#1 PHY register needs to be overridden.
sku ID:0,1 Astronaut (USB)
port#1:
PERPORTPETXISET = 7
PERPORTTXISET = 2
sku ID:61,62 Astronaut (LTE)
port#1:
PERPORTPETXISET = 7
PERPORTTXISET = 5
BUG=b:68120012
BRANCH=master
TEST=emerge-coral coreboot chromeos-bootimage
Change-Id: Icf5c9e5f4dae15630ec4d6ca6648cae78ca910c6
Signed-off-by: Ren Kuo <ren.kuo@quantatw.com>
Reviewed-on: https://review.coreboot.org/22135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add a devicetree option to set temperature adjustment registers
required for thermal diode sensors and PECI. However, this commit does
not have the code needed to make PECI interface actually use these
registers. It only applies to diodes.
As a temporary workaround, one can set both THERMAL_DIODE and peci_tmpin
to the same TMPIN, e.g. TMPIN3.mode="THERMAL_DIODE" and peci_tmpin="3".
PECI, apparently, takes precedence over diode, so the adjustment register
will be set and PECI activated. Or simply use the followup patch, which
makes THERMAL_PECI a mode like THERMAL_DIODE.
I don't have hardware to test THERMAL_DIODE mode, but in case of PECI,
without this patch I had about -60°C on idle. Now, with offset 97,
which was taken from vendor bios, PECI readings became reasonable 35°C.
TEST=Set a temperature offset, then ensure that the value you set is
reflected in /sys/class/hwmon/hwmon*/temp[1-3]_offset
Change-Id: Ibce6809ca86b6c7c0c696676e309665fc57965d4
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This commit just moves the vboot sources into
the security directory and fixes kconfig/makefile paths.
Fix vboot2 headers
Change-Id: Icd87f95640186f7a625242a3937e1dd13347eb60
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Microcode blob has been updated, so update the length to match
Change-Id: I46ac10e5c6cd6492c98a7034649797f301101abc
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The USB settings were wrong in some places, or missing and the
USB_OC values were taken from the schematics.
Change-Id: I29b564a4161c486f5e8556b1726471bfa2351b7a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/22043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Disable SataDevSlp and update other values to match vendor/AMI firmware.
Change-Id: I6f278be54b86450575c366d68bfa6a67575b0fdd
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The RComp values have been updated to match what is shown in the schematics.
Extracting the Memory configuration blob from the original BIOS (A blob
which contains the correct binary sequence matching the RComp values appears
in object with GUID 2D27C618-7DCD-41F5-BB10-21166BE7E143), I could find
and confirm the DQ and DQS mapping.
Small code cleaning in romstage.c with no effect.
Change-Id: I35c734269b365fd759e9bd56224a80a8a8df5a57
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/22041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Check CBFS for 'serial_number' field, and use value if exists;
otherwise use value set at compile time.
Change-Id: I4b50f6310ca32b9dd372db075a5b5729e3b06619
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/22040
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add the missing device and ensure it shows up in the devicetree prior
to PCI enumeration.
Change-Id: Ia2c4ba1200422b36c533e86065a4fcd10c4b2722
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22055
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the missing device and ensure it shows up in the devicetree prior
to PCI enumeration.
Change-Id: I44c7df6a2be149ed61094f67ef1c578736e5b55c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Beside the high-resolution eDP panel, it features a dual-mode
mini-DP port.
Change-Id: Iae60c1f930f5778ee3b5d9d19227168257e9ae06
Tested-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/22125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Add GPE configuration table.
Remove GPE3 from the power button ASL and set the EC to GPE3(AGPIO22).
Set the EC and PCIE/WLAN SCI GPIO signals.
Set GPE ASL methods for:
PCIE/WLAN 8h
EHCI 18h
XHCI 1fh
Note EC GPE3 methods are in the EC ASL.
BUG=b:63268311
BRANCH=none
TEST=Test lidswitch powers the device on and off at the login screen.
Change-Id: I27c880ee84b6797d999d4d5951602b654ede948e
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22096
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set PL2 based on either 90% of usb c charger's max power or sku id if
using a barrel jack.
BUG=b:37473486
BRANCH=None
TEST=output debug info for different skus and make sure
PL2 set correctly.
Change-Id: I487fce4a5d0825a26488e71dee02400dbebbffb3
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/21772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Stoney Ridge has one EHCI controller and one XHCI controller.
Also, update the Kahlee and Gardenia mainboards ASL to match.
Change-Id: I5749ca0640796732e74e551147f8c4446317b77e
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change the board name from cannonlake U DDR4 to U LPDDR4 to match
actual platform.
TEST=NONE
Change-Id: Id350e3cbc299d49431197ef5f914ea9a7310a0a5
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/22112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
|
|
Include common platform.asl to have generic indication of power
transition state of system.
TEST=Enter and resume from S3, check the post code had been changed to
0096 and 0097.
Change-Id: Ic38ac6d7e60441caeba5c088c9dbe4d901355782
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/22111
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
|
|
In the original AGESA headers, these tables are not defined as const.
Cast them to void * so that they'll work with either version of the
headers.
BUG=b:64766233
TEST=Build in cros tree and upstream coreboot, with old headers
and updated headers.
Change-Id: I75387b57caf5a3c6c25655120aafd942254b5c73
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22059
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There was no reason to have the AGESA callout tables in each mainboard,
so move them to soc/amd/common.
Move chip specific functions into the stoneyridge directory:
- agesa_fch_initreset
- agesa_fch_initenv
- agesa_ReadSpd
Combine agesa_ReadSpd and agesa_ReadSpd_from_cbfs, and figure out which
to use.
Soldered-down memory still needs to be supported in a future commit, as
stoney supports both DDR3 & DDR4. A bug has been filed for support for
the upcoming Grunt platform.
BUG=b:67209686
TEST=Build and boot on Kahlee
Change-Id: Ife9bd90be9eb0ce0a7ce41d75cfef979b11e640b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Apu3 and apu5 are additional variants of apu2 board.
Apu3 has no LPC connector exposed, but has additional USB header. It has
also 2 slots for SIM cards and one of the gpios is used to control
switching between them.
Apu5 is differing by having 6 SIM card slots (3 SIMSWAP switches).
This patch adds support for those other variants by not introducing
additional code redundancy.
Change-Id: I4fded98fed7a8085062cdea035ecac3d608cd2a0
Signed-off-by: Kamil Wcislo <kamil.wcislo@3mdeb.com>
Reviewed-on: https://review.coreboot.org/21981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add GPIO initialization for mc_bdx1 mainboard. Call init_gpios() as
early as possible as FSP will set up things (like hiding PCI devices)
rather early. If connections on the mainboard are dependent on GPIO
settings then FSP can screw things up (e.g. disabling not yet connected
PCI root ports).
Change-Id: I003277cfb871f861900b7fcdc5ec851d4c1c1e6a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/22035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Creates identical object files.
Change-Id: Ie8adb21a753cee6a72dae5eeb64a255e6ead2fe7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21652
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Change-Id: I907f55622e6aaba401471239f706ab24cd26319f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
These were OEM configurations hidden inside a header file, notation
was already dropped for f15tb and f16kb.
Change-Id: Id64fa861fd516e9f7cae9eba9b8145e033fe9bdd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
This change adds timestamps to romstage in order to keep
PC Engines apu2 platform in active codebase.
Change-Id: Ie0286d4982623da9d035c47df6077edaf51e5110
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/22071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change adds support for logging EC events during S0ix resume.
BUG=b:67874513
TEST=Verified that EC events are correctly logged during S0ix resume:
284 | 2017-10-16 20:45:12 | S0ix Enter
285 | 2017-10-16 20:45:16 | S0ix Exit
286 | 2017-10-16 20:45:16 | Wake Source | Power Button | 0
287 | 2017-10-16 20:45:16 | EC Event | Power Button
288 | 2017-10-16 20:45:35 | S0ix Enter
289 | 2017-10-16 20:45:40 | S0ix Exit
290 | 2017-10-16 20:45:40 | Wake Source | GPIO | 112
291 | 2017-10-16 20:45:40 | EC Event | Lid Open
292 | 2017-10-16 20:50:51 | S0ix Enter
293 | 2017-10-16 20:50:59 | S0ix Exit
294 | 2017-10-16 20:50:59 | Wake Source | GPIO | 112
295 | 2017-10-16 20:50:59 | EC Event | Mode change
Change-Id: I9f6dcb8852d94ebf90bb5b63a17fde524d58d49f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch provides configuration parameter to enable/disable
Intel Speed Shift Technology.
Change-Id: I95a240e8be6e19ac0e14698ab33543c491a8c974
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/22049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Enable Audio DSP by default on cannonlake rvp platform.
TEST=Boot up into OS and check Audio driver debug print.
Change-Id: I6892c6d349019550c967ef30b84d385f396fc388
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/21888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Define PCI express clock usage for cannonlake u and cannonlake y rvp
based on board design.
TEST=Bootable into OS.
Change-Id: I7d71d9a87d87ce6a3e3270f67518afdd54a48db4
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/21879
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
14" BigDaddy needs to override USB2 TxiSet additionally to
enhance driving strength.
Otherwise EA test will fail on USB2 eye pattern.
BUG=b:67820719
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: I674c121a71866a5d44439eeb49e07f917d816de8
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch skips SPD data reading when system resumes from S3 since
MRC cahce is adopted and validated in fsp_memory_init.
BUG=b:67021596
TEST=Run suspend/resume on Fizz and make sure the systems are
working well when system resumes from S3. Checked dmidecode
information and SMBIOS type 17 data is the same with cold
boot.
Change-Id: I1692fca8456290d1471973b746537b5fec504e03
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/21987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Set SCS emmc HS400 enable FSP parameter.
TEST=Boot to OS, verify HS400 SDHCI print
Change-Id: I3ef8a6740ef985a0c51115d9b0ea753b5db2c70d
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/22008
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
|
|
This is already selected in `src/cpu/amd/agesa/Kconfig`.
Change-Id: I691a2ade10ee461b6bc34ea24d57a911281791f3
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/22011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Replace the support for Cannonlake U DDR4 board to Cannonlake U LPDDR4
platform.
TEST=Able to boot up on CNL U LPDDR RVP.
Change-Id: I2a3dd39875705dcb93a60ceba7c143e3e5328148
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/22001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=b:65386429
BRANCH=none
TEST=panel lights up
Change-Id: I9871969314b9b64bee2b20332e35bfc6fbd2ddda
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/22002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Remove IRQ and MP tables. Modern OS use ACPI instead of legacy tables.
Use Kconfig for reversable configuration if using old OS.
BUG=b:62241143
Change-Id: I5fc833c8af47b5f6fad757e129250e6202810dbb
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/21963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Enable PCIe Advanced Error Reporting for PCIe
root port 2, 3, 4 ,8.
BUG=b:64798078
TEST="lspci" shows that AER is enabled in the capabilities list.
Change-Id: I6438250d674e7d06cdecd8f25fadebca1973721e
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/21946
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use GENERIC_SPD_BIN method of adding the SPD bins to final rom.
Change-Id: I242e393bafac41aa7743f83b52cadf027019ee6e
Signed-off-by: Kamil Wcislo <kamil.wcislo@3mdeb.com>
Reviewed-on: https://review.coreboot.org/21980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
For Kahlee, the AMD firmware directory should be in the 1MB location
so that it's in the RO cbfs section.
BUG=b:65484600
TEST=Build & boot
Change-Id: I650d8bc0bfa773f5fb5dc11167fe3db3b9550b68
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22003
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove sample configuration code for internal
Broadcom GbE device in AMD A55E aka Hudson-E1.
Change-Id: Ib0262805aafc62513d9237019ade473cb1efbf1c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Notify the EC the system is going to sleep.
Change-Id: I025e268a4f806d827348d91effff43a6a339a148
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/21881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Forward the apmc call to the chromeec.
Change-Id: Id724c1abf15617ad1ba28f2c0247455b014c1867
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/21880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add support for google/wizpig (white label Chromebook) as
a variant of the cyan Braswell baseboard.
- Add board-specific code as the new wizpig variant
- Add new shared SPD file to the baseboard
Sourced from Chromium branch firmware-strago-7287.B,
commit 02dc8db: Banon: 2nd source DDR memory (Micro-MT52L256M32D1PF)
Change-Id: I424d2256eb79ca3ea0a62620954c57c09ae0c0b2
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21577
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add support for google/ultima (Lenovo Yoga 11e G3) as
a variant of the cyan Braswell baseboard.
- Add board-specific code as the new ultima variant
Sourced from Chromium branch firmware-ultima-7287.131.B,
commit 3ef9e73: Revert "Revert "soc/intel/braswell: Put SERIRQ in quiet mode""
Change-Id: Ib38b110f50f4d6ae6eda40e787cd3c1c8dd5ece7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
|
Add support for google/setzer (HP Chromebook 11 G5) as
a variant of the cyan Braswell baseboard.
- Add board-specific code as the new setzer variant
- Add new I2C touchscreen device and SPD files to the baseboard
for potential reuse by other variants
Sourced from Chromium branch firmware-strago-7287.B,
commit 02dc8db: Banon: 2nd source DDR memory (Micro-MT52L256M32D1PF)
Change-Id: Ibcebebeb469c4bd6139b8ce83a1ca5ca560c2252
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This updates board info of PC Engines platforms, changes board names
to official manufacturer's names and adds info about ROM. Removing
"Clone of" option for ALIX platforms makes them independent.
Change-Id: Ie76d65ea84f14b9043a8e5b86678a9da4c187cc9
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/21722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
SPI mode needs to be set early to normal and Quad I/O disabled
on this board for some reason
Change-Id: I4dbc52010eebf492087d0b1c155a24a307bcc8b0
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/21945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
TESTED on Biostar A68N-5200: boots to GNU/Linux
With proprietary VBIOS, even the gfx works in SeaBIOS.
Change-Id: Id44b81345ba189f82413042760d570a746294a1e
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/21872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|