| Age | Commit message (Collapse) | Author |
|---|
|
The PCI_INTR table is an Index/Data pair of I/O ports
0xC00 and 0xC01. This table is responsible for physically
routing IRQs to the PIC and IOAPIC. The settings given
in this table are chipset and mainboard dependent, so the
table values will reside in the mainboard.c file. This
allows for a system to uniquely set its IRQ routing.
The function to write the PCI_INTR table resides in
cimx_util.c because the indices into the table have
the same definitions for all SBx00 FCH chipsets.
The next piece is a function that will read the PCI_INTR
table and program the INT_LINE and INT_PIN registers in
PCI config space appropriately. This function will read
a devices' INT_PIN register, which is always hardcoded to
a value if it uses hardware interrupts. It then uses this
value, along with the device and function numbers to
determine an index into the PCI_INTR table. It will read
the table and program the corresponding value into the PCI
config space register 0x3C, INT_LINE. Finally, it will set
this IRQ number to LEVEL_TRIGGERED on the PIC because it is
a PCI device interrupt and the must be level triggered.
For example, the SB800 USB EHCI device 0:18.2 has an INT_PIN
value hardcoded to 2. This corresponds to PIN B. On the
Persimmon mainboard, I want the USB device to use IRQ 11. I
will program the PCI_INTR table at index 0x31 (this USB device
index) to 11. This function will then read the INT_PIN register,
read the PCI_INTR table, and then program the INT_LINE register
with the value it read. It will then set the IRQ on the PIC to
LEVEL_TRIGGERED by writing a 1 to I/O port 0x4D1 at bit position 4.
Also, the SB700 has slightly different register definitions than
the newer SB800 and SB900 so it needs its own set of #defines for
the pci_intr registers.
Only the Persimmon mainboard is adapted to this change as an
example for other mainboards.
Change-Id: I6de858289a17fa1e1abacf6328ea5099be74b1d6
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/5877
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
S3 resume is expected to work now, however the 3s delay and flash wear
is still there.
Change-Id: I7edbce7bcf9c2160099fd5e371562b1ec63d45d8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5971
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
S3 resume now works, however the 3s delay and flash wear is still there.
Change-Id: I9d2eda5454baf7704807cf67f3aca94a67de3406
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5970
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
|
|
Change-Id: I5df1f0efdef2592b762fe391edaadbca4593e85a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5689
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I9c8f7cc98c65102486e17ec49fa2246211dffc4f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5688
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Ibbb07ef308c7e92a8a8dfe066f5e3866d5f8aee2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5687
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I158993bcb654ef27a9fc6b7e9dc3fc955fb740fa
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5686
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I3ac39441746d739ac19e831bb67c76405c24ba27
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5925
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
1. Remove #include .c in romstage.
2. Make romstage component symbols linker-time.
3. Provide header guards and prototypes in superio romstage support.
4. Correct function type-signatures to be static/non-static where
appropriate, avoid 'pretend optimisations' by unnecessarily inlining
functions.
5. Separate out UART enable from various other PNP hard coding
Change-Id: I9b8dad7c02d802e97db73ddf2913d5c6bb33a419
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5916
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Rewrite smsc/smscsuperio romstage component to be more consistent and
provide header there-by removing #include's of early_serial.c's in
mainboard's.
Change-Id: I572e0c76422f09d4de88935a36c0a59e5350e6e0
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5915
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
These non-ROMCC boards #include the model specific w83977tf Super I/O
romstage component. The generic winbond_early_serial() function serves
well here to further tighten integration into the new Super I/O
framework and drop dependence on #include'ing .c files, leaving only
ROMCC boards.
Change-Id: Ib63c0f29f994c54e6112702506f288535799706c
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5898
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Move samsung/stumpy board towards generic romstage component and away
from poorly written hard-coded model specific Super I/O component. This
is an incremental step towards getting obj-level abstraction between
board and Super I/O.
Change-Id: I358c5abef85c2ffa1b7178025cde8834a35b0a51
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5899
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I280441aadb0575dc0b99584cdcd48cc76a0289a2
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5284
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I5cb496d0d582d3dc5c0c0635f632561f8a3dd853
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5897
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
The lock bit for UVSVC/LVSVC was set before both registers were programmed.
Change-Id: I000440db5c8dd2f260ebc1b69108b75621faf7b3
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5167
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Without it option ROM run results in just a black screen.
Change-Id: Id203f55ca0f02c290a3f40ac1ec7c5f23c5580bf
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5344
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
thinkpad_acpi checks that BIOS version matches some pattern.
Report version in this form.
Not cleaned up as the idea of this patch seems to be met with resistance.
Can make it Thinkpad-specific if the idea is accepted.
Change-Id: I15e33e87e7a7f42d6a06f12fb39b5172153af8a1
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4650
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Make superio romstage component link-time symbols.
Change-Id: Icde27465a05946498ff7b8f1aaa7a9e8ba074272
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5880
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Move towards the removal of the superio model specific xxx_serial_enable
implementation. Make remaining superio romstage parts link-time symbols
and fix corresponding mainboards to match.
The following mainboards remain unconverted as they are ROMCC:
- mainboard/supermicro/x6dai_g
- mainboard/supermicro/x6dhe_g
- mainboard/supermicro/x6dhr_ig
- mainboard/supermicro/x6dhr_ig2
and so block the final removal of w83627hf_serial_enable().
Special cases:
- mainboard/supermicro/h8qme_fam10: Provide local pnp_ sio func
Provide local superio pnp_ programming entry/exit functions as to avoid
making superio implementation global symbols. Although this is not the
proper/final solution, it does mitigate possible symbol collisions and
allow for continued superio refactorisation.
Change-Id: Iaefb25d77512503050cb38313ca90855ebb538ad
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5601
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Part 1/2: These are actually not necessary if Super I/O support is
properly utilized.
Change-Id: I39b621e582f8d0762276d29492c91dce500f0665
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5870
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Bay Trail-I Platform – Bayley Bay-I Customer Reference Board
The Bayley Bay CRB-I is a dual-channel DDR3L SO-DIMM non-ECC platform.
It is designed to support the Bay Trail-I SoC.
This implementation uses the Intel FSP (Vist the Intel FSP
website for details on FSP architecture and support).
This code does not currently support S3. All other features and IO
ports are functional. Booted on Ubuntu 14.04, Mint 16,
Fedora 20 with SeaBIOS payload. Memtest86, FWTS, and
other tests pass.
Notes:
- Generates a 2MB binary to be flashed to the upper 2MB of the ROM,
to preserve the existing Intel Flash Descriptor & TXE binary.
- Tested with B0 & B3 Baytrail I parts
Board support page will be updated on acceptance.
Change-Id: I80c836c7590f2dc25ec854e7a0bb939024cea600
Signed-off-by: Martin Roth <gaumless@gmail.com>
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/5792
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Depreciate the model specific early_serial.c romstage component for this
Super I/O in favor of the recent generic winbond romstage framework.
Change-Id: I22775dc9b6341c8994d21591b7176abe4dd99911
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5724
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
Depreciate the model specific early_serial.c romstage component for this
Super I/O in favor of the recent generic winbond romstage framework.
Convert dependent board to generic winbond serial init. Note the clock
function is actually invalid since it never enters into PNP config mode
to twiddle the register. Further, 48MHz is the default (page 9 of
data-sheet) and so romstage.c need not do anything to the clock rate
hence why it presumably works with this invalid function.
Change-Id: I4706a1446c1b391b8390ac0361700ce6f15b9206
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5725
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
We now have common ite_*_*() functions for romstage and hence no longer
require the model specific portion of this superio support.
Change-Id: I30400abf27008a88072673075bba445f100d9ad3
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5838
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
Convert mainboard's that use model specific romstage functions of
it8712f to the generic framework by following the reasoning of:
a7d14a1 ite/common: Introduce common watchdog and 3.3V VSB helpers
Change-Id: I1485306a951103c9a4bc0dbe87c416c91f46c36f
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5737
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Change-Id: I2ff70cafdd808a235ed4f0663e182d306f493c7e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5685
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Removed function only read ACPI MMIO base address from a couple of
registers in IO space.
Change-Id: I25a31b7ac1706b9eebc5db0b9604039928328b0a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5683
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I9f27e1e814a80864d8ca315fe816a083c55708c6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5682
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Pass parameter Func like fam14, fam15tn and fam16kb.
Change-Id: I262bf88e431f7035e668ac8f3fb29ac0690b3e52
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5681
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This is x86 "standard" 0xcf9 reset mechanism.
Change-Id: Ieb48290b21a7cb1425881fdd65c794e96da0248f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5680
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
These boards return with AGESA_UNSUPPORTED, while other boards return
AGESA_SUCCESS here when there is no hardware for external reset signalling.
Change-Id: I5aed211b1812888af55a691cfbfa8d7b5aff91bc
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5679
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Most of the callouts are not specific to board or even family.
Start new file with default callouts doing nothing and returning
either AGESA_SUCCESS or AGESA_UNSUPPORTED.
Also add callout for returning empty IdsIdData. This feature is
not used and could be easily overriden at board-level at later time.
Change-Id: I65dbcdd80dddc89d47669ebe62c22caa63792f5c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5678
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: I219ae74d60fd7211de2edee96e74bbe13130bb94
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5849
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: I31841e7bf578c77d08d452779936fcf5b3026d4f
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5848
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Spotted by Clang
Change-Id: I26201c7f5e421c38d3965d8e7e62c4a8e670e449
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5833
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: Id967f6057759cf0603c84514d32b067c3658306f
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5831
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: I4e5f2d7e8e6b76703fccce38fc7e3165d763e97f
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5830
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Depreciate the model specific early_serial.c romstage component for this
Super I/O in favor of the recent generic winbond romstage framework.
Change-Id: I529c9cd1d8d63db3035b4828b3c3fc43911f49ce
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5727
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Remove bogus attempt to double program the Super I/O. Remove also a
questionable function that enters Super I/O LDN config space, does no
actual LDN programming, rather multi-function register programming and
then never leaves the config space. Further, we don't export pnp_
symbols from the early_serial.c component into the global namespace.
Change-Id: I7d6b97b174249ae16fe881728da5ca3dd069b696
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5800
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
The F2A85-M has IT8603E which is a strip down version of IT8728F.
Change configuration from provisional IT8712F to the IT8728F.
While at it also enable only needed LPC bridge decodes.
As the side effect, this change also implements setup of environmental
controller, thus it87 driver can detect the temperatures/fans.
Change-Id: I22067b13ea27ee37e959a246718d9559c2a3215d
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/4499
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: I6c5cc46385581d6b69d20f6bc9b016b799765d9e
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5829
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: Idda1a49277c156670014fac27b9f1c378f8df0cd
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5827
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: I61fe91e467c29f144323af9c4612420f322098b4
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5826
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: I46fad8d236c620ee5dbeb24f4517f20f00db839f
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5825
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: If948960abbd927aa6d2b471a42a2321a04d992f3
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5824
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: Idd7305cb34be77894ca4b6062bc0a2dc61126347
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5822
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Following the reasoning in:
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: I5be77fe6670601e103260077fae07a5b9fd41f1d
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5821
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
These are not local headers.
Change-Id: Ie0b0a682565a08dbfa089986dc7860fdb0846949
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5796
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
Change-Id: I29037c322dac5ed9ebc36b95bc1981acf21e5bd0
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5778
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
These NIC stub drivers were to initialize the Gigabit Ethernet adapters
just enough to keep coreboot from trying to execute an option ROM.
However this is no longer required as non-VGA option roms are not ran;
See:
b32816e Remove PCI_ROM_RUN option
Change-Id: Idc44619767c631c5fcf550a5948c8947bde5e218
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5777
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Remove use of global variables uma_memory_base and uma_memory_size
from builds with Intel northbridges, as these variables can be kept
within the chipset or even as stack locals.
Intel platforms have no functional implemenation for option GFXUMA.
If we did implement some choice between external and integrated graphics,
it needs to be named in less obscure fashion.
Change-Id: I12f18c4ee6bc89e65a561db6c2b514956f3e2d03
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5720
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This defines new board_info entry 'Vendor name' to be displayed in place of, or
in addition to, the CONFIG_VENDOR string 'Google'.
Also flag these as flashrom accessible SPI without socket. Instructions to
disable flash write-protection can be found at Chromium developer documentation.
Change-Id: I69791a091417a80d01e0ba2c6462417730a07be0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5750
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
While at it, fix frontrunner-af board URL.
Change-Id: I3b631830d679abc20f8a72411f2402689d9f9aac
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5706
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
|
|
When the system is started with dock, the serial port works.
As soon as the laptop is undocked and redocked, the serial port
no longer works. See below superiotool dump snippet:
Upon bootup: SIO @ 0x2e
LDN 0x03 (COM1)
idx 30 60 61 70 71 74 75 f0
val 01 03 f8 04 03 04 04 02
Redocked: SIO @ 0x2e
LDN 0x03 (COM1)
idx 30 60 61 70 71 74 75 f0
val 00 03 f8 04 03 04 04 02
Since the function dock_connect is executed every time the
dock is reconnected, starting without a dock and then attaching
it to a dock is now also fixed.
Change-Id: Ibd97589a8c743673a55e382a5db2ba62656c595e
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: http://review.coreboot.org/5761
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The Codec and ALS both have interrupt sources that can be configured.
The ALS kernel driver currently does not try to use it but the codec
driver does for things like jack detect.
ACPI Devices are added, but as with other ACPI devices the HID may
need to be updated once more official strings are decided.
BUG=chrome-os-partner:24380
BRANCH=baytrail
TEST=manual: build and boot on rambi and check for functional lightsensor
Change-Id: Ib51a2aaf32d5597926fcbe9183947e9ac53e1468
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/182366
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5049
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
In order to support probing I2C devices when the controller is
in ACPI mode the mainboard needs to decalre them in the proper
scope with the address/interrupt information. The touchpad devices
are ATML0000/ELAN0000 and the touchscreen is ATML0001 so they can
be distinguished in userland scripts based on ID. There is also
a special "ISTP" node that indicates whether the devices is a
touchpad (=1) or touchscreen (=0) in case this is useful to drivers.
These names may not be final but they are a starting point and can
be easily changed.
Atmel devices also have a bootloader mode which needs to be
declared as a separate device. Unfortunately it does not work as
expected to have multiple I2cSerialBus() resources declared in a
single device and have it select properly, even with the use of
StartDependentFn(), so bootloader devices are declared separately.
The original devices are left in \_SB scope and are only enabled
if the I2C controllers are in PCI mode. The new devices are only
enabled if the I2C controllers are in ACPI mode.
BUG=chrome-os-partner:24380
BRANCH=baytrail
TEST=manual
1) Ensure there is no change in functionality by default and that
the devices are still probed by chromeos_laptop in the kernel.
2) Enable lpss_acpi_mode=1 in devicetree.cb and kernel changes to
add _HID entries for devices in appropriate drivers. Ensure that
the devices are probed successfully. Further changes are needed
to the chromeos-touch-firmware scripts to load config and update
firmware based on the new ACPI _HID entries.
3) Put touchpad in bootloader mode (by flashing bad firmware) and
ensure that it is detected at address 0x25 and the firmware is
able to be updated.
Change-Id: I5b9b47ddc94474a677497271e963f62cb09438e0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/182259
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5045
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Nothing can actually use this as the EC cannot speak
using baytrail's SERIRQ protocol. Also, the voltage
bridge is going away so nothing will be hooked up to it.
Therefore disable this it.
BUG=chrome-os-partner:24693
BRANCH=rambi
TEST=Built and booted.
Change-Id: I406bb9c227578ec0a75eaf67143b3b27cb7880ae
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/182082
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/5042
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Fix build regression introduced in:
a823f9b mainboard/lenovo: Add Lenovo Thinkpad T520 support
Change-Id: I60d92f8cceda6427f43e6be9d78c2af82af4b061
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5738
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Short list of known issues for this patchset:
* Suspend/Resume - does not work
* Combi pci card for SD/MMC card reader with IEEE1394 - not found
* Shutdown - sometimes does not work as expected
* At least mysterious harddrive i/o
Change-Id: Iaba8d1f5e471cfeca20d82f4e1b416641e1f2ae9
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: http://review.coreboot.org/5672
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
Set critical temperature thresdholds to 70C. This will cause DPTF
framework to shut down the system so it may need to be higher or
lower but will need some testing.
BUG=chrome-os-partner:17279
BRANCH=rambi
TEST=build and boot on rambi, start DPTF framework and observe it
using specified critical thresholds.
Change-Id: Ibbf6d814295eb5ff006cb879676b7613f5eb56a3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/182025
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5038
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
- Add passive thresholds for thermal participants
- Disable the charger participant and remove from _TRT
BUG=chrome-os-partner:17279
BRANCH=rambi
TEST=build and boot on rambi and start ESIF framework
Change-Id: Ie5917413aceadee6e39594257aaafb0bcb399d09
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/181663
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5029
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
KBD_IRQ# is moved to GPIO SC101, with SC50 going back to its original
SERIRQ function.
Note that this change breaks Rambi 1.5 keyboard functionality.
BUG=chrome-os-partner:24424
TEST=Manual on Rambi 2.0. Verify KB functions in OS with SC50 / SERIRQ KB
interrupt toggling removed from EC code.
BRANCH=Rambi, Glimmer, Clapper
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I3fa40441741ea9d52a6e2ff15925570510b5b82b
Reviewed-on: https://chromium-review.googlesource.com/181757
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5030
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This is a empty struct that has propagated through the superio's & ec's
but really does nothing. Time to get rid of it before it adds yet more
cruft. However, since this touches many superio's at once we do this in
stages by first changing the function type to be a pure procedure.
Change-Id: Ibc732e676a9d4f0269114acabc92b15771d27ef2
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5617
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
We should configure i8254/i8259 down in to the southbridge rather than
romstage of every AGESA/CIMx board much like Intel boards do.
Change-Id: Id7c4f0baa0819d52aef9b0ee03c20d0fa16b9352
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5669
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The SoC needs to provide a 32k clock signal SUSCLK for
some modems to work properly, so this enables the signal.
BUG=chrome-os-partner:24425
TEST=Manual, check SUSCLK pin with a scope.
Change-Id: Ibc0d5bb38a2c3e16f381dfc256097fdced67fd1c
Reviewed-on: https://chromium-review.googlesource.com/180101
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Bernie Thompson <bhthompson@chromium.org>
Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Tested-by: Bernie Thompson <bhthompson@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5722
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
Tested-by: build bot (Jenkins)
|
|
eMMC CLK was incorrectly configured as PULL_UP, but should have been
PULL_DOWN. 2K pulls somehow masked this problem.
BUG=chrome-os-partner:24353
TEST=Verify eMMC is bootable on Rambi on boards that previously failed
with an all-20K, all-PU eMMC pin configuration.
BRANCH=None
Change-Id: I0cbb6ebbb6818f83402b99330728266b09a0f5d6
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/181034
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5026
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Rambi's reference code will live at slot 3 in the
verified firmware section.
BUG=chrome-os-partner:22867
BRANCH=None
TEST=Built and booted. Verified correct area where
reference code was loaded from.
Change-Id: I8bee46600429ac8f732fe334852f69aff1324150
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/180027
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/5024
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Not used currently on rambi board. Disable in case it
saves power.
BUG=chrome-os-partner:23862
BRANCH=none
TEST=build and boot on rambi
Change-Id: Idb870c2cfa88cb6c3f1ada3caf0db566e33ec1eb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/180084
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5020
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
With the ACPI GNVS exported and depthcharge changed to
initialize eMMC in ACPI mode we can now put the SCC
devices into ACPI mode.
BUG=chrome-os-partner:24380
BRANCH=none
TEST=build and boot on rambi, test eMMC and SD card
Change-Id: I39716198f8227c0c3293ac23eb09660792e2c51b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179901
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5018
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Make use of the ITE common Super I/O framework and there-by removing any
hard coding of Super I/O base address.
Change-Id: I14af89d2727d7c6bac0f9840043c430726297429
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5717
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Following the reasoning of:
cf7b498 superio/fintek/*: Factor out generic romstage component
Change-Id: I4c0a9a5a7786eb8fcb0c3ed6251c7fe9bbbadae7
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5585
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Lines with 'select SERIAL_CPU_INIT' where redundant with the
default being yes. Since there is no 'unselect SERIAL_CPU_INIT'
possibility, invert the default and rename option.
This squelches Kconfig warnings about unmet dependencies.
Change-Id: Iae546c56006278489ebae10f2daa627af48abe94
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5700
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Turn on WDT support in the devicetree. Turn off CIR support.
Dispense with old commentary.
Change-Id: Icf0c0e12a0ed7ce6c3b6176653e076ffc2ba937e
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5698
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
CPU - fsp_model_206ax:
- Remove Kconfig options and mark this as using the FSP.
- Use shared FSP cache_as_ram.inc file
Mainboard - intel/cougar_canyon2:
- Update to use the shared FSP header file.
- Modify to call copy_and_run() directly instead of returning to
cache_as_ram.inc.
Northbridge - fsp_sandybridge:
- remove mrccache, fsp_util.[ch]
- add fsp/chipset_fsp_util.[ch] with chipset specific FSP bits.
- Update to use the shared FSP header file.
These changes were validated with FSP:
CHIEFRIVER_FSP_GOLD_001_09-OCTOBER-2013.fd
SHA256: e1bbd614058675636ee45f8dc1a6dbf0e818bcdb32318b7f8d8b6ac0ce730801
MD5: 24965382fbb832f7b184d3f24157abda
Change-Id: Ibc52a78312c2fcbd1e632bc2484e4379a4f057d4
Signed-off-by: Martin Roth <gaumless@gmail.com>
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/5636
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Following the same reasoning as commit
d3043313a91dff3bc2f879ffb3b4bf23a364d711 superio/fintek/f81865f: Avoid
.c includes
Clean up the early_serial #include directives in mainboard/romstage code.
Change-Id: Ia6ed36c8517a95b651fefdd855eec0ec91d73187
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5439
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Overriding global config entries in mainboard directory Kconfig
files often raise unnecessary warnings. Squelch some of those.
Change-Id: Ib5127672ae068670028aa25c8ccb5366277622f2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5699
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This enables the DPTF framework, but it doesn't do much
without some sort of kernel+user components to drive it.
BUG=chrome-os-partner:17279
BRANCH=none
TEST=build and boot on rambi, dump DSDT and look over \_SB.DPTF
Change-Id: Icb632a6e70c3912bbdfa6ef3f5c87cd79d2b8a3a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179480
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5003
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
These are the values that are seen with VBIOS and
may need tweaked for derivative panels.
BUG=chrome-os-partner:24367
BRANCH=none
TEST=boot on rambi in normal mode and see the panel come up
Change-Id: Ie3120ab3c5298135626e8534d3954acd263dc74b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179365
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5001
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Now that the SD card controller is limited to the SD card
2.0 spec it's possible to use 20K pulls for the pads.
BUG=chrome-os-partner:24423
BUG=chrome-os-partner:24312
BRANCH=None
TEST=Built and booted. Able to dd to/from /dev/mmcblk1 without
any errors.
Change-Id: Id5396c55330a84bf7a09d227507d2bfcde66a1a4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179423
Reviewed-on: http://review.coreboot.org/4999
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
The rambi board can only meet the SD card 2.0 specification.
Therefore, the controller capabilities need to be overridden
to match.
BUG=chrome-os-partner:24423
BRANCH=None
TEST=Built and booted. /sys/kernel/debug/mmc0/ios shows
high speed as maximum timing as well as 3.3V signal voltage.
Change-Id: Ib3824800852376e0f15a70584917d6692087ccfe
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179415
Reviewed-on: http://review.coreboot.org/4998
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Bay Trail has 3 banks of gpios. Therefore, in order to
properly identify a gpio the specific bank number as well
as the GPIO within that bank is needed. The SPI
write-protect GPIO is GPIO 6 within the SUS bank (offset
0x2000).
BUG=chrome-os-partner:24324
BUG=chrome-os-partner:24408
BRANCH=None
TEST=Built and booted. Looked at GPIO sysfs in the
chromeos_acpi directory.
Change-Id: Ic51b5abe3bacf6cf9b6a90cf666f1a63b098a0e3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179195
Reviewed-on: http://review.coreboot.org/4995
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Leave it under BOOTMODE_STRAPS to control whether these have
any functional meaning on the build.
Change-Id: Ieb59aa7ab4b1e8da6a1002e7a8e5462eb7988d35
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5643
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Ib8448f3d36a23538cd9fea897f09da3ec4ad007a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5647
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I72471ac68088cd26f8277b27b75b7d44ad72cfc4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5642
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
This feature is no longer specific to ChromeOS builds.
Change-Id: If27d4dc7caff8a551b5b325cdebdd05c079ec921
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5641
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change-Id: I7b3d044fad1d6973910e9bef347478a45c149a4f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5640
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Provision the configuration of the Fintek F71869AD Hardware Monitor's
configuration by way of devicetree.cb. Make use of this in the
jetway/nf81-t56n-lf board to properly control fan's.
Change-Id: Ic25b29d1b7a9145e0e209b490b25a2cbc46cb75c
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5580
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Facilitate for the configuration of so called "Multi-function Select
Registers" with devicetree.cb in ramstage.
Make use of this new functionality in, mainboard/jetway/nf81-t56n-lf to
correctly configure the Fintek's multiplexed GPIO pins to be in AMD TSI
mode. This allows the Fintek to correctly talk to the Southbridge over
the SMBus for CPU temperature data as to control fans and so on.
Change-Id: I80abcd8b767fc4b22d00d1384ce4ef89fe837e3d
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5576
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
romstage reports a completely unintelligible printf of "error level:",
fix this and document meaning of the return values in source.
Change-Id: Ia2fb9a6206e08822f6c2f62b69bf22cdae2ba819
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5465
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
ec_in_rw needs to be read by depthcharge, which only supports legacy
GPIOs.
BUG=chrome-os-partner:24408
TEST=Manual on Rambi. Cold + warm boot device, verify that depthcharge
detects the proper ec_in_ro state.
BRANCH=None
Change-Id: I25802b445c795eb85580c22d880efee8eeb21318
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179228
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4993
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
Strengthen PUs on all eMMC pins to fix problems with eMMC not coming up
on certain boards.
BUG=chrome-os-partner:24353
TEST=Manual. Burn FW on board that previously failed to boot eMMC,
verify chromeos can now install + boot from eMMC.
BRANCH=none
Change-Id: I7a9742968b8b8c2c42285ffc21de46aed9c87fb7
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/178917
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4991
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Rambi 1.5 boards use the native SD card controller on baytrail.
Therefore, enable those signals. The CLK, D*, and CMD pins use
2K pulls as these were shown to not exhibit any errors when
doing reads or writes to a DDR50 sd card.
Note that if a servo is connected on needs to enable the
sd_vref_sel rail to pp1800 as this causes issues with card
detect if it is not set to pp1800.
BUG=chrome-os-partner:24312
BRANCH=None
TEST=Built and booted. Tested sd card read and write works in kernel.
Also noted that write protect detection works as well.
Change-Id: I520e2808acbd8494534fcb710411dbc0e12fc874
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/178961
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4990
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Rambi has the LPE audio codec connected to PMC_PLT_CLK[0].
Configure it for 25MHz.
BUG=chrome-os-partner:23791
BRANCH=None
TEST=Built and booted. Noted message in console output.
Change-Id: I11297ba951149e5831c65ca70ac7bdbbed113098
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/178781
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4987
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ic555d23a9112677a784dd814601f8202d4d17261
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/5691
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Some 1.5 boards have a single channel ram configuration.
Accomodate such configs.
BUG=chrome-os-partner:22865
BRANCH=None
TEST=Built and booted ChromeOS.
Change-Id: I513327e47b9211d2dd1ea960d7da671a3773cb91
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/178340
Reviewed-by: Nick Sanders <nsanders@chromium.org>
Tested-by: Bernie Thompson <bhthompson@chromium.org>
Tested-by: Nick Sanders <nsanders@chromium.org>
Reviewed-on: http://review.coreboot.org/4983
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The level shifting between 3.3V and 1.8V for the SERIRQ
signal is not working. Instead use the SERIRQ pad as
a gpio which is used as a direct IRQ signal for the
keyboard interupt.
BUG=chrome-os-partner:23965
BRANCH=None
TEST=Built and booted rambi. Keyboard works with associated EC change.
CQ-DEPEND=CL:177189
Change-Id: Ifc270ca38207828a6d4711551d4bde9121559cca
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/177223
Tested-by: Bernie Thompson <bhthompson@chromium.org>
Reviewed-on: http://review.coreboot.org/4979
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The romstage code for rambi uses the mmio way of reading
inputs. However, this is a problem is the GPIOs are set up
as legacy mode. Subsequent warm resets mean the ram_id is
read incorrectly. Ensure the ram_id is read consistently
by keeping the GPIOs for ram_id in mmio mode.
BUG=chrome-os-partner:24085
BRANCH=None
TEST=Built and booted. And rebooted. Now seeing consistent ram_id
values on warm resets.
Change-Id: Ieff98c000be80998854f325754f1e819975d2be5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/177230
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4977
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Some of the drivers in the kernel were not so happy about
having shared IRQs. Also, sharing IRQs means more code
needs to be run in interrupt context to determine if the IRQ
was meant for a particular device. Fix this.
No more 'mmc1: got irq while runtime suspended' messages.
BUG=chrome-os-partner:24056
BRANCH=None
TEST=Built and booted. Looked at /proc/interrupts and noted no
more sharing between pci devices.
Change-Id: Ie5da102204ffe3156dd55ab17af77df245a57c97
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176792
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4973
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The kernel chromeos_laptop driver nomenclature expects the
board name to not be in all caps. Fix this as well as the i2c
address for the trackpad.
BUG=chrome-os-partner:24307
BRANCH=None
TEST=Built and booted. trackpad device is found. IRQs still not
working yet.
Change-Id: Id6be8ee4bce2835e303ea4fe63944be80d2d7ec2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176680
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4970
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Also add the relevant info about these pins to the ASL tables + add
SMBIOS type 41 data for these parts.
BUG=chrome-os-partner:22863
TEST=Manual on Rambi. Set some pins to GPIO_DIRQ, and then verify DIRQ
regwrites w/ GPIO_DEBUG look correct.
Change-Id: Id40655f9fb2ea7b10e1ff58d0b2a8b4cc6f05ff8
Reviewed-on: https://chromium-review.googlesource.com/176299
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4963
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
