| Age | Commit message (Collapse) | Author |
|---|
|
Change-Id: I3a8e077656df02912b4e67c3947bd5af054a18bf
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The following was tested:
- CPUs with 800, 1067, 1333MHz FSB (1333MHz FSB needs a jumper set)
- The VGA output with libgfxinit
- USB
- COM1
- Ethernet
- SATA
- PCIe
- PCI
Has the following problems:
- The Ethernet NIC is not usable after S3 resume and requires Linux to reload
the driver. Vendor firmware also has this problem so it is quite likely it
is just a atl1c driver problem.
TODO: Add documentation
Change-Id: Ibce9ecdc0e44db3703401f116c9a8bff5b66437f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
STAPM programming was created inside function OemCustomizeInitEarly().
It should be SOC specific, and called by agesawrapper just before the
call to OemCustomizeInitEarly().
BUG=b:116196626
TEST=build and boot grunt
Change-Id: I8a2e51abda11a9d60a9057b38f2a484e1c8c9047
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28705
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit creates an ampton variant for Octopus. The initial settings
are copied from Bip, but the following changes are made to support
hardware differences:
* GPIO_66 is not connected (LTE).
* GPIO_67 is not connected (LTE).
* Updated comment for GPIO_134 (EC_AP_INT_ODL), but not configured yet.
* GPIO_143 is not connected.
* GPIO_144, GPIO_145 mapped to PEN_EJECT are not connected.
* EN_PP3300_TOUCHSCREEN moved from GPIO_213 to GPIO_146.
* GPIO_213 is not connected.
* GPIO_214 is not connected.
BUG=b:111498206
TEST=None
Change-Id: I7d6cf19c906df19115b1101e3d91c62f5f3f61e3
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/28663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add new mainboard variant of whiskey lake rvp, which is primary
validation platform for whiskey lake silicon, support socket DDR4 memory
module.
BUG=N/A
TEST=Build and flash, confirm boot up into kernel on whiskey lake rvp
platform.
Change-Id: I4a5e8a9ec76d5e55e55ef9bf968825c17fbe9816
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch sets the MRC UPD "CmdTriStateDis" to disable TriState for
the rammus boards. Rammus is LPDDR3 design without RTT for CMD/CTRL.
BUG=none
TEST=Run memtester app and also webgl fishtank on the LPDDR3 kabylake
boards and also check the margin data is proper in FSP.
Change-Id: Iee115f49ba5b36dc5b0425e9da02b58cd19b2236
Signed-off-by: Marx Wang <marx.wang@intel.com>
Reviewed-on: https://review.coreboot.org/28568
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's only DDR4 or LPDDR3 support for coffelake processor line,
details can be found out on EDS #570805.
BUG=N/A
TEST=N/A
Change-Id: I8ba6b6861b15b40b01237f87c8d55394f7fd6706
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add gpio programming difference for whiskeylake rvp platform.
BUG=N/A
TEST=N/A
Change-Id: I35a0384f828fd3219e0c3adb4830f5bdab800e32
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28367
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set up EC_IN_RW GPIO to boot depthcharge. Without this patch,
depthcharge will fail to tell if the EC firmware is RW.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui and see in logs, that depthcharge detects
EC_IN_RW GPIO.
Change-Id: Icb39d663f65b72e0ad54059c9590d9693106ee25
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/28670
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change GPP_D17 and GPP_D18 to no connects as DMIC was moved
to DMIC0.
BUG=b:113744731,b:111106010
TEST=none
Change-Id: I8ef42627e542182707c81389af9da33a114bc184
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28689
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Grunt variants need a way to customize the mainboard vendor based on the
platform. For future boards, this can probably be done via CBI, but
grunt doesn't support that method.
BUG=b:79874904
TEST=Build, boot, see updated mainboard vendor
Change-Id: I997dc39c7f36f70cf4320ef335831245889eb475
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/28651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@google.com>
|
|
Update Power Limit1 and Power Limit2 values along with stepsize.
Correct the charger effect for Temperature sensor2.
BUG=b:112448519
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: I01e0a94fe694537d9eebe3b92c11d0c83137d716
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/28530
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A negative side-effect is that those boards disappear from the board-status
output, but this is an issue on all variants.
Change-Id: Ic80804dc1f7d9c6f83ceee3db667019532c31d4c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28626
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The board_id() definition is the duplicate of chrome EC board_id
definition. Remove the duplicate definition and select
EC_GOOGLE_CHROMEEC_BOARDID Kconfig item.
BUG=b:114001972,b:114677884,b:114677887
Change-Id: Id8b7027d653649e8e5791e455652c4e893a746c2
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Tested-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reviewed-on: https://review.coreboot.org/28609
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The helper function to get the board version from EC returns 0 on
failure. But 0 is also a valid board version. Update the helper function
to return -1 on failure and update the use-cases.
BUG=b:114001972,b:114677884,b:114677887
Change-Id: I93e8dbce2ff26e76504b132055985f53cbf07d31
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Tested-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/28576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
|
|
Update DPTF settings based on recommendation from thermal team.
BUG=b:112550414
BRANCH=None
TEST=Manually tested by thermal team.
Change-Id: I26f09392a3293ce4b3481f2be341a667d606bc10
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-on: https://review.coreboot.org/28666
Reviewed-by: Todd Broch <tbroch@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable DRAM_PART_NUM_IN_CBI feature to get DRAM part number from CBI
and set DRAM_PART_IN_CBI_BOARD_ID_MIN to 1 for EVT.
BUG=b:115965629
TEST=verified it in meep proto board which rework ram id.
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I962b099d5b9fbe0ca29708be1e9c6ed60b10d363
Reviewed-on: https://review.coreboot.org/28658
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Change-Id: I4fcdb7467f1911af722f4c24ce64807079a91340
Signed-off-by: Evgeny Zinoviev <me@ch1p.com>
Reviewed-on: https://review.coreboot.org/28620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
With the addition of new boards using macros to set per board settings in the
same gpio.c file is getting too complicated so link separate files.
Change-Id: I3ab05f1af6ba0a04dd827816b3bcaa506a3f6aff
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
AMD has tested careena, and for the time being is recommending a scalar
of 68%, power limit of 7.8 W and time constant of 2500. Using new STAPM
configuration code, set the desired values.
BUG=b:111561217
TEST=none, code was tested with grunt.
Change-Id: I42671ab0e66b21dc4f8c8c326c1fa33328b1390e
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
While the pin was set to a pull-down, with the external pull-up, this
wasn't enough to keep the pin low. Set to output low to drive to 0V.
TEST=Boot grunt, verify EMMC_BRIDGE_RST is 0V.
BUG=b:115661061
Change-Id: Ife014b8a879274df5d892c1de386976808de1df0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
These values override the default subsystem IDs, and aren't needed.
BUG=b:113253260
TEST=Boot grunt
Change-Id: I3c56534b094ede8d8200b72f4433a891d0094064
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/28652
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
PC Engines boards are interfaced mainly via serial console.
Enable SeaBIOS serial console for these boards by default
when SeaBIOS selected as payload.
Change-Id: I9e65dd1e28859028c8c46f28a5442de8c59d4893
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/27824
Tested-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Default STAPM percentage causes a lot of thermal throttling on grunt.
AMD experimented with 80%, it works for grunt. This is initial code to
provide easy change path for other grunt based platforms.
BUG=b:111608748
TEST=build and boot grunt.
Change-Id: I22863f6ed76152bf872fce3e275f8a7fd8077504
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add google/buddy (Acer Chromeboase 24) as a variant of google/auron,
with the following changes:
- add buddy-specific variant code
- add handling to auron for buddy's lan init, which no other variants have
- add handling to auron's mainboard ACPI due buddy having different PCIe
port assigments than all other variants
Ported from Chromium branch firmware-buddy-6301.202.B, commit
ebb82ce [Buddy: Lock management engine + SPI descriptor]
Test: build/boot Linux on google/buddy using SeaBIOS and Tianocore payloads
Change-Id: Ib76eef47677b72ddaef81a2decef189a5f20c20a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/28613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Use an empty weak function for variant_romstage_entry(), rather than
having separate empty functions for boards which don't utilize it.
Change-Id: I7a278ed716484bea377a5dd98d4a534502c8bab6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/28612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Set up EMMC gpios for payloads.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: I1e7ee9bfe3a26ed04374e8c74243f48552a1d254
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/28546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
As we don't use the MIPI camera on Rammus, disable SA Imaging Unit and
CIO2 devices to avoid the system failed to enter S0ix.
BUG=b:114502527
BRANCH=master
TEST=On DUT, echo freeze > /sys/power/state
1. check the S0ix status on EC console
2. check the value of /sys/kernel/debug/pmc_core/slp_s0_residency_usec
Change-Id: I91629732db01ee534f0ddb67a2b358d725ef810e
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/28543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We have a pin from AP to EC, called AP_IN_SLEEP_L (SRCLKENA0 on AP side,
pad R23) that is supposed to be high in S0, and low in S3 (and X/don't
care in S5).
This should be set as early as possible in bootblock.
BUG=b:113367227
TEST=make; boots and verified AP_IN_SLEEP_L GPIO is high.
BRANCH=None
Change-Id: Icd59fa366c162e7443b8932a851e65f110f551ab
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/28585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@google.com>
|
|
Turn on SOC_INTEL_CANNONLAKE_MEMCFG_INT for coffeelake rvp platform
for easier collabration on newer platform. The setting in memory.c get
from board design itself.
BUG=N/A
TEST=Build and boot up with whiskey lake rvp platform.
Change-Id: I10f3af4bed511153cef4d6f3a93caea57cc4ae90
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28257
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch sets the MRC UPD CmdTriStateDis for the atlas boards.
Atlas is a LPDDR3 design without RTT for CMD/CTRL.
The original change for
nocturne is I0f593761dcbd121e7e758421af178931b9d78295
mb/google/poppy: Set UPD CmdTriStateDis for Nocturne
BUG=b:111812662
Change-Id: I45b6dd22412c689c8db64f4650e9fa9e87dec2ec
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
At ECC 2017 user Bob reports, that an image built for the Lenovo T500
runs on the Lenovo W500 without any issues.
Change-Id: I17fd9725ab85ba2f0c99a70f40e35432265a81c1
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/22226
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Felix Singer <migy@darmstadt.ccc.de>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3eacba9c1c20bbfa270dd7a9afabe48ed9092bcc
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/28622
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ram_resource is board specific and should be moved there.
Change-Id: I50bd9aaaae39422e565d8bf205a6365c59299df0
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/28621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
IOMMU was tested on Xen 4.8 and Linux kernel 4.14.33. Following feature
set is enabled:
(XEN) AMD-Vi: Disabled HAP memory map sharing with IOMMU
(XEN) AMD-Vi: IOMMU Extended Features:
(XEN) - Peripheral Page Service Request
(XEN) - Guest Translation
(XEN) - Invalidate All Command
(XEN) - Guest APIC supported
(XEN) - Performance Counters
(XEN) AMD-Vi: IOMMU 0 Enabled.
Change-Id: I6dbfae78849248f3532caa78974c8f2ce61a530d
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-on: https://review.coreboot.org/26116
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9f7e7d70b850619e34a60fd8e7b16b44c728e9ca
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Based on SiFive bootloader code
Change-Id: I71043ce9e458e25e64da28d53cd36b02d2e22acc
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/28604
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Invoke clock_init in romstage for SiFive Unleashed.
Change-Id: Ib869762d557e8fdf4c83a53698102df116d80389
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/28602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The board version is part of EC's EEPROM, but is not being populated
from EEPROM. Instead a default Kconfig parameter is returned as board
version. Select GOOGLE_SMBIOS_MAINBOARD_VERSION Kconfig item to enable
requesting the EC for board version.
BUG=b:114001972,b:114677884,b:114677887
Change-Id: Ib404a9da35156e197d232088fd7ca69432effbca
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Tested-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/28539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This modification for DVT build and use CBI method
enable all memory particles.
BUG=b:112870780
TEST=verify it under the EVT unit and pre-test EVT
unit(rework RAM ID follow the proposal) respectively.
Change-Id: I488a0652ba348eff9a6d8591b0cfa6ed4fe808aa
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28579
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I637792d3bf22d2e452144d44ba03cfe45b47501d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28580
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
HAVE_INTEL_FIRMWARE is used to enable certain options that rely on a valid
Inter Flash Descriptor to exist. It does *not* identify platforms or boards
that are capable of running in descriptor mode if it's valid.
Refine the help text to make this clear.
Introduce a new option INTEL_DESCRIPTOR_MODE_CAPABLE that does simply
declare that IFD is supported by the platform. Select this value everywhere
instead of the HAVE_INTEL_FIRMWARE and default HAVE_INTEL_FIRMWARE to
y if INTEL_DESCRIPTOR_MODE_CAPABLE is selected.
Move the QEMU Q35 special case (deselection of HAVE_INTEL_FIRMWARE) to
the mainboard directory.
Change-Id: I4791fce03982bf0443bf0b8e26d9f4f06c6f2060
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/28371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Only for those that are x86 and also have a RW_LEGACY region.
The assumption is that all devices touched have 64k block sizes when
choosing size and alignment of the region.
Change-Id: I12addb137604f003d1296f34f555dae219330b18
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add MICRO 4G and 8G SPD file.
BUG=none
BRANCH=master
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure system boots up.
Change-Id: I7cb5b7f2bcdc6fbe0cbc640cad4af014f1a0edd6
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28484
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
add two memory parts and ram id:
hynix_dimm_H5ANAG6NCMR-VKC
micron_dimm_MT40A1G16KNR-075E
BUG=b:113983573
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: Ia052f16b6c1e64ee6458fbdeea56a482a728c35a
Signed-off-by: Ren Kuo <Ren.Kuo@quantatw.com>
Reviewed-on: https://review.coreboot.org/28536
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On rammus, headset uses DA7219 so that we need to enable it.
BUG=b:112945714
BRANCH=master
TEST=emerge-rammus coreboot chromeos-bootimage
Flash FW and check in kernel to see if DA7219 is up.
Change-Id: I92dd412374d007aab264661e698fbbbbcf1eae45
Signed-off-by: marxwang <marx.wang@intel.com>
Reviewed-on: https://review.coreboot.org/28537
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch sets the MRC UPD CmdTriStateDis for the
nocturne boards.Nocturne is LPDDR3 design without RTT
for CMD/CTRL.
BUG=b:111812662
TEST=Run memtester app and also webgl fishtank on
the LPDDR3 kabylake boards and also check the
margin data is proper in FSP.
Change-Id: I0f593761dcbd121e7e758421af178931b9d78295
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/28379
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
VPD reference: https://chromium.googlesource.com/chromiumos/platform/vpd/+/master/README.md
Copy ChromeOS VPD driver to add support for VPD without CROMEOS.
Possible use case:
* Storing calibration data
* Storing MAC address
* Storing serial
* Storing boot options
+ Now it's possible to define the VPD space by choosing
one of the following enums: VPD_ANY, VPD_RW, VPD_RO.
+ CHROMEOS selects now VPD as part of it.
+ VPD is implemented as driver.
Change-Id: Id9263bd39bf25d024e93daa57053fefcb1adc53a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25046
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
AMD chips don't hold off a reset to the end of I2C transitions, so
devices on the i2c bus can be left in a bad state. To avoid this,
make sure the trackpad and touchscreen chips get disabled
during boot.
BUG=b:114411165
TEST=build, reboot watch trackpad enable go low
Change-Id: Ie50f4a102249df79517da571a6e768dba804cd57
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28538
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds support for a x2 NVMe device on PCIe bus PCIe lines 5+6 and
clock#4.
BUG=b:113369699
TEST=booted on atlas
Change-Id: I08e7c4d65662ddbb7d936915c896eb1fcb240ba8
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Id7e8ad63de2a6094c66cbd47ae9b7707a9af4e81
Signed-off-by: Mikolaj Walczak <mwalczak@fb.com>
Reviewed-on: https://review.coreboot.org/28529
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
this enables spi console for wedge100s with broadwell_de. the console
size is 64kb. enabling spi console in `board.fmd` enables code which
calls into `timer_monotonic_get` (from `spi_flash_cmd_poll_bit`) and
`udelay` (from `ich_status_poll`). this patch selects `TSC_CONSTANT_RATE`
in fsp_broadwell_de's Kconfig to satisfy that.
Change-Id: Ib925c5aee88b65c46a81534405c364dd5649f8e8
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-on: https://review.coreboot.org/28528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
This change configures GPIO_63 (which is used for H1 interrupts) as Rx
Level. This ensures that the signal gets passed on to the next logic
state as is and the APIC entry can be configured to trigger interrupt
on level or edge as per the kernel driver expectation.
TEST=Verified that no H1 interrupt timeouts are seen with 100
iterations of warm and 100 iterations of cold reboot.
Change-Id: I7aac30300a4251d9b40276dcca7ebc6a6d814c40
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
this enables mrc cache in fmap for wedge100s and always enable it in
Kconfig.
Change-Id: I27cd236f67a6500b40fc3eb731397d408402f041
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-on: https://review.coreboot.org/28527
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On rammus, system halt was observed because of gspi clk value being set to 0.
Log info from serial coreboot:
FMAP: area RW_NVRAM found @ 9fa000 (24576 bytes)
SF: Detected FAST_SPI Hardware Sequencer with sector size 0x1000, total 0x1000000
VBNV: Restore from flash failed
ASSERTION ERROR: file 'src/soc/intel/common/block/gspi/gspi.c', line 443
gspi.c
442
443 assert(gspi_clk_mhz != 0);
444 assert(ref_clk_mhz != 0);
445 return (DIV_ROUND_UP(ref_clk_mhz, gspi_clk_mhz) - 1) & SSCR0_SCR_MASK;
BUG=none
BRANCH=master
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure system boots up.
Change-Id: Ibe3937902901b2cdc1a196415c08fabb0f3155f2
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28405
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DMIC's are now connected to DMIC_CLK0/DMIC_DATA0.
So, enable the pins accordingly.
BUG=b:113744731,b:111106010
BRANCH=none
TEST='emerge-nocturne coreboot chromeos-bootimage' builds the image
Change-Id: I48cace3c6099a2853fcb377c695a5e325094baf6
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/28433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Nautilus-Wifi with m3 AP got a halt issue during CTS test.
Nautilus-Wifi was FCS with Celeron AP first and also its PCB/BOM was
validated only with Celeron. Since Celeron deos not support turbo
boost mode, its steady power demend and lower CPU frequency may not
reflect the potential noise hidden inside the board.
Bumping VCC_SA voltage offset 75mV confirmed works to mitigate the
potential noise coupling to VCC_GT/SA, and we verified this change
makes this issue go away on Nautilus-Wifi board.
Nautilus-LTE doesn't show this issue, since it has 10L PCB, will have
better grounding and less noise/ripple than 8L PCB.
BUG=b:111417632
BRANCH=poppy
TEST=Verified CTS test pass without an issue.
Change-Id: Id13fcc36a5b6ed42620c66f57a7303f30bff1a50
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/28439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change enables tablet mode ACPI device for all octopus boards.
BUG=b:113348027
Change-Id: I69a5dd41cd0958b93f8eed338fed4b6ee77a178f
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28466
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Set GPIO135 high to enable audio through the BCLK buffer.
BUG=b:113559558
TEST=None
BRANCH=grunt
Change-Id: I1dcecf5960d3c91e0c2165e7f8856ff423c06e8c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28482
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use ICH10's file instead of ICH7's.
Change-Id: I02678179e8f1dbd9b9f7d6407383a7a6cad15011
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/28450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add CMOS option that allows to use both integrated and discrete GPU.
Tested on ThinkPad W530.
Change-Id: I8842fef0fa1235eb91abf6b7e655ed4d8598adc7
Signed-off-by: Evgeny Zinoviev <me@ch1p.com>
Reviewed-on: https://review.coreboot.org/28393
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the mainboard.c in order to support the sku id in smbios
table where the sku id is queried from the eeprom via EC.
BUG=b:113714761
BRANCH=master
TEST=check the result of 'dmidecode'
Change-Id: I3413784cca1ac10a2468d84f2d06c0e1d701fdcb
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/28426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable dGPU power handling on Lenovo ThinkPad T430, T530 via PMH7
register 0x50.
Although there's no Thinker-1 chip on these models according to
schematics, dGPU power control via PMH7 works the same as on T420/T520,
so they can be considered Thinker-1-compatible.
It can be tested from linux userspace using util/pmh7tool.
To turn dGPU power off:
pmh7tool -c 0x50 7
pmh7tool -c 0x50 3
To turn it on:
pmh7tool -s 0x50 3
pmh7tool -s 0x50 7
To check whether it is on (bash):
reg=0x$(pmh7tool -r 0x50)
echo "$(( (( reg & 0x08 )) >> 3 ))"
or just `pmh7tool -b 0x50 3` with
https://review.coreboot.org/#/c/coreboot/+/28388/
Tested on ThinkPad W530.
Change-Id: Ieab1a33b3c680c757cc0999660b5cb7e122474cc
Signed-off-by: Evgeny Zinoviev <me@ch1p.com>
Reviewed-on: https://review.coreboot.org/28392
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the DRIVERS_SPI_ACPI to enable the tpm device node.
Without DRIVERS_SPI_ACPI, the kernel will popped out the below error:
cr50-update[592]: Starting cr50 update
cr50_get_name[595]: updater is /usr/sbin/gsctool -s
cr50-update[609]: exit status: 3
cr50-update[613]: output: Could not open TPM: No such file or directory
cr50_get_name[615]: board_id: '' board_flags: '0x', extension: 'prod'
cr50-update[617]: hashing /opt/google/cr50/firmware/cr50.bin.prod
cr50-update[678]: current state 3 in /var/cache/cr50.a3055efbc9.state
cr50-update[682]: not running
cr50-result[782]: Not running normal image. Skip setting Board ID
trunksd[795]: TPM: Error opening tpm0 file descriptor at /dev/tpm0: No such file or directory
BUG=none
BRANCH=master
TEST=/dev/tpm0 is created
Change-Id: I35287c6c54299c2677c41fc830675570b9d45a94
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/28400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable Synaptics touchpad device for liara
BUG=b:113309346
BRANCH=master
TEST=Verify touchpad on liara works with this change
Change-Id: Icdafe34a00fd55d5338fa07ffa304e48e7b85e7b
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch overhauls the Cheza FMAP, removing some sections we don't
seem to need (RW_CDT, the two RW_XBL_BUFFERs, and the second copy of
RW_DDR_TRAINING), and adding new sections we're going to need soon or
should have had anyway (RO_DDR_TRAINING, RO_FSG, RW_LEGACY).
Make more use of implicit offsets and sizes, because we can and because
it should make future adjustments easier.
Change-Id: I0bd9e59e9cfa162c478c4bd1f048fcac61ad5062
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/28403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: T Michael Turney <mturney@codeaurora.org>
|
|
After adjustment on Liara Proto
Audio: 399.2 KHz
H1: 398.3 KHz
TP: 399.0 KHz
BUG=b:113319200
BRANCH=master
TEST=emerge-grunt coreboot chromeos-bootimage
measure by scope
Change-Id: Ibba8c823ed8451a804cf731d49e7568a94ac7c6b
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Because of an incorrect transmit voltage swing, the signal must be
adjusted. The factor of slices for full swing level can be corrected via
the High Speed I/O Transmit Control Register 3.
Change-Id: I116802cd2a944658fc3022e948eba43cebe52bb4
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Alex Thiessen <alex.thiessen.de+coreboot@gmail.com>
|
|
Set threshold parameter for grip sensor STH9321
.ProxCtrl6: 75
.ProxCtrl7: 99
BUG=b:113303916
BRANCH=poppy
TEST=Built and verified parameter passed to driver
Change-Id: I8a410a23b5e3831fc8e90118b810fc2409a026eb
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/28381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Enrico Granata <egranata@chromium.org>
|
|
Also removed internal pull ups for CX_PREQ_L and
CX_PREQ_L signals as they have external pull ups.
BUG=b:110654510
TEST=On Yorp Proto 2, flashed image and verified that it boots to OS.
Checked Wake-on-Wifi works with both cnvi and pcie modules.
Also executed a few suspend resume cycles.
Change-Id: I0a76cd2a1481c828fc092aaf7e870a411624879c
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/28328
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Grunt takes a few seconds to update the EC, so display a notification
screen while that's happening.
BUG=b:113286040
TEST=Boot Grunt with old EC firmware, see update screen
Change-Id: I95fc4d3430bac66c09f57a4d34abde08752e5f0e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add weida touchscreen support
BUG=none
BRANCH=master
TEST=emerge-octopus coreboot, and verified that touchscreen works on
meep.
Change-Id: I4352322820237e4c2289410af6643e15109060a1
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Modify the previously SOC_CNL_LPDDR4_INIT to SOC_CNL_MEMCFG_INIT, to
make the infrasturture to handle both LPDDR4 and DDR4 cases in the
future. Consider the case of reading SPD from SMBus other than providing
SPD pointer directly.
BUG=N/A
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully.
Change-Id: I2f898147f67dd52b89cc3d9fc4e6b3854fa81f57
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28248
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set EC SPI bus config and init SPI bus according to the config.
BUG=b:80501386
BRANCH=none
TEST=EC is not working yet. This makes depthcharge go forward a little.
Change-Id: Id9209b6429417430cfcf7f5a5a1659e7e4bc7866
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/28251
Reviewed-by: Joel Kitching <kitching@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set up EC interrupt GPIO to boot depthcharge. Without this patch,
depthcharge will fail to detect EC interrupt GPIO.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui and see in logs, that depthcharge detects
EC interrupt GPIO.
Change-Id: I0ec2c70c189a059219954e0384aaf98995285728
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/28250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The firmware of devices connected to LPC should deassert the LPC CLKRUN#
signal when there is no bus activity on LPC.
Necessary changes:
- Enable LPC CLKRUN#
- Enable LPC PCE (Power Control Enable)
- Enable LPC CCE (Clock Control Enable)
- Remove I/O decoding range on LPC for COM 3
- Disable I/O UART driver
Change-Id: I2fd80e3fdcf23658f97b8182a77df7e09ddf25d6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Bayhub eMMC controller default runs SD base 50MHz at the first power on.
After boot into OS, mmc kernel driver will config controller to HS200/208MHz
and send MMC CMD21 (tuning block).
But Bayhub PCR register 0x3E4[22] (eMMC MODE select) is not clear
after system warm reset.
So eMMC will still run 208Mhz but there is no block tuning cmd in depthcharge.
It will cause two Sandisk eMMC (SDINBDA4-64G-V/SDINBDA4-32G-V) to fail to
load kernel and trap in 0x5B error (No bootable kernel found on disk).
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: Ic080682e67323577c7f0ba4ed08f8adafca620cc
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Reduce the CPU passive threshold sample rate from 5 seconds to 1
second so DPTF will react faster to rapid temperature increases.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BUG=b:113101335
BRANCH=atlas
TEST=manual performance/power testing on nocturne.
No longer see messages like below in syslog,
'CPU0: Package temperature above threshold'
Change-Id: I2dc9d157b54500bae29e123978bb8ad6e05ef619
Reviewed-on: https://review.coreboot.org/28325
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Reduce the CPU passive threshold sample rate from 5 seconds to 1
second so DPTF will react faster to rapid temperature increases.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BUG=b:67459049
BRANCH=nocturne
TEST=manual performance/power testing on nocturne.
No longer see messages like below in syslog,
'CPU3: Package temperature above threshold'
Change-Id: Ic20c718fd3a496db7c7192feec4f230d924cc458
Reviewed-on: https://review.coreboot.org/28324
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update TSR1 trip point from 48C to 50C.
Also, change power limit2 minimum value from 8W to 10W.
These are the values as per recent thermal tuning.
BUG=b:79779737
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: I33a9d2dc3e0e5566d95b1f1e46d3922dc8965b2b
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/28187
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit fixes the values and thus fixes the issue of
audio device not getting detected on random reboots.
Change-Id: I34a4f62815d192005c3324d4f71b0aba377fe738
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/28280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
|
|
Change-Id: Ie3ee4acfd272991133f02a56df6e23aa6071d3e9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Some unneeded includes are also removed.
Change-Id: Icd518c46d8503d11d24466c30840d7e514e9a05d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Most FADT report using ACPIv3 FADT table. Using the get revision
function keeps the table versions in sync.
Change-Id: Ie554faf1be65c7034dd0836f0029cdc79eae1aed
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28277
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch disables the unused PCI clock outputs on the XIO2001 PCI
Express to PCI Bridge.
Change-Id: I0b9cf51a713f4ab46e71d250397486d136c26177
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28284
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
add device "WCOM Digitizer" and "Synaptics Touchpad" for bobba
BUG=none
BRANCH=master
TEST=emerge-octopus coreboot
Change-Id: Ie0bf8ebab6d9cb9c8fe42a500efaa3d11ae359db
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28332
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
TEST: same sha256sum with BUILD_TIMELESS=1.
Change-Id: Icf3368bcf1351f0e7cd4041c3792d76362aec9e5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
To increase the lifetime of the circuit, it is necessary to reduce the
eMMC speed to DDR50 mode.
Change-Id: I40658b44a99e6600ed00950a1a177961f0055e7a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This enables CBAS device on Nocturne to allow hid-google-whisker driver
in kernel properly detect device configuration.
Change-Id: I5905a2de208e94062f2768a9b7d22147f85c7f38
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-on: https://review.coreboot.org/28262
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For the 1st redesign of mc_apl1 mainboard some adjustments are
necessary:
- The FPGA is now connected directly via a PCIe Root Port
- Internal Apollo Lake UARTs are now used
- Adjusting GPIO settings
Change-Id: I8917a52325306f24d1c39a88dac47b0cee760d57
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
A FPGA is not necessarily available in further mc_apl1 variants. So we
move the loading of the driver and the notify function to the mc_apl1
variant.
Setting the CPU to Max Non-Turbo Ratio is also not absolutely necessary
for further variants.
Change-Id: I9f8438407f231df08e1ad04655bb6f747257e268
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This supports the Foxconn d41s, d42s, d51s, d52s.
The following is tested (SeaBIOS 1.12 + Linux 4.9) and works:
- COM1
- S3 resume (with SeaBIOS needs sercon disabled)
- Native graphic init on VGA output
- SATA
- USB
- Ethernet
- PS2 keyboard
The base for this mainboard port was the Intel D510MO port.
Change-Id: Ie4ec9cbf70adcdddbc2e5d805e4806825c320072
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28227
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
src/mainboard/google/octopus/mainboard.c
Function dev_find_slot may return NULL,
check before its usage.
Found-by: klockwork
BRANCH=None
TEST=Built & booted Yorp board.
Change-Id: I160adbe3b0a5a2b0f11fd1567513860664d4bee3
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28235
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The change updates GPIO configuration for meep.
1. Update touchscreen power enable GPIO in devicetree.
2. Provide default override tables for GPIO configuration.
BUG=b:112955087
TEST=Boot on meep proto board with Intel (Jefferson Peak) wifi card.
Change-Id: Idb4e7a510eef15c2e118058d5848080782f4f665
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/28252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Since ifdfake has been deprecated in favor of better alternatives, such
as flashrom IFD parsing. Therefore, there is no need to support ifdfake
any further. Remove the IFD_*_REGION values on the few motherboards with
them.
Change-Id: Ie07116a7fb960c6ca832d802016f22c6677baac9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28232
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates the board id check for version >=2 to apply new
GPIO configs.
BUG=b:112618194
Change-Id: I3544c9596c465615818d2040682e554a64fc6b1a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28263
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This should not be board specific.
Change-Id: Ifa617e84af767f33a94f1ddfa7d4883c1a45198f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change PL1 from 4.5W to 7W, based on thermal test results.
BRANCH=eve
BUG=b:73133864
TEST=Verify the MSR PL1 limitation is set to 7W.
Change-Id: Ic3629f9c3b7eb6eef1a1b5a3051c9a11448bc9ad
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28078
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds support for controlling the keyboard backlight over ACPI.
BUG=b:112619894
BRANCH=none
TEST=verified keyboard backlight can be adjusted using keyboard
shortcuts
Change-Id: I25713f341e8b5a4e50903ac109bfa717f20969d8
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28205
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Enhanced Intel SpeedStep (EIST) on nocturne.
Change-Id: Ie9b832f5bc3a5ef300783bd9bcd7cf5d186b98fa
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
