| Age | Commit message (Collapse) | Author |
|---|
|
QEMU does not have a separate northbridge chip, so the mainboard
needs to handle the ACPI name and paths so that devices can get
generated into the SSDT properly. This fixes the PIRQ and TPM
table generation.
This issue can be seen in the coreboot output:
ACPI_PIRQ_GEN: Missing LPCB ACPI path
Change-Id: Ifc7d4359eea38ac0b55d655e39191ae7f8655fe4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Ensure that the low memory is properly reserved so it does not get
marked as normal RAM and get wiped or reused by firmware or the kernel.
This ensures that the low RSDP is always available for the kernel.
This is only noticed if something wipes the RSDP before the kernel
boots, which happens if you use the depthcharge payload and boot in
developer mode.
Change-Id: I7295018416229bc957ecbf26f77623a57965557e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
When the TPM is enabled in QEMU the fw_cfg interface will return
~200KiB of ACPI tables, so this needs to be increased from the default
in order to be able to boot.
This is seen when using a TPM with qemu as it will hang when
processing the fw_cfg tables.
qemu-system-x86_64 \
-machine q35 -enable-kvm -vga virtio -serial stdio \
-drive 'id=hd,file=disk.bin' -bios coreboot.rom \
-chardev 'socket,id=swtpm,path=/tmp/swtpm/swtpm-sock' \
-tpmdev 'emulator,id=tpm0,chardev=swtpm' \
-device 'tpm-tis,tpmdev=tpm0'
Change-Id: I21980aace8e86e636f5ae7b55148f4c31404edba
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Was accidentially removed in 6e50849
Change-Id: I090b6bc8863d17412cb1e23ac816c39f479290c1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39937
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the variants' devicetrees are almost identical, convert to
using an overridetree setup for simplicity.
Test: build all slippy variants, compare generated static.c to ensure
resulting generated contents unchanged (although layout will)
Change-Id: If237fad38a1bccfb8e51edfae3ecb75d05ade240
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Clean up Link's mainboard dir by putting the SPD files in
a spd subdirectory like all other/newer boards use, and
selecting GENERIC_SPD_BIN to include them in the build.
Test: build google/link and verify spd.bin unchanged
Change-Id: I9c2f9f77dbdd6552c5ae1e7a0df2051b9b85badc
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Link's DID data makes no sense, and ACPI backlight controls don't work
as a result. Replace them with the default profile used by most/all
other boards.
Test: build/boot google/link, verify ACPI backlight controls functional
Change-Id: Ia7cb3f10bd3c05ebaf414c17a8f94d2e9b40ae26
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Currently, those who want to use measured boot implemented within
vboot should enable verified boot first, along with sections such
as GBB and RW slots defined with manually written fmd files, even
if they do not actually want to verify anything.
As discussed in CB:34977, measured boot should be decoupled from
verified boot and make them two fully independent options. Crypto
routines necessary for measurement could be reused, and TPM and CRTM
init should be done somewhere other than vboot_logic_executed() if
verified boot is not enabled.
In this revision, only TCPA log is initialized during bootblock.
Before TPM gets set up, digests are not measured into tpm immediately,
but cached in TCPA log, and measured into determined PCRs right after
TPM is up.
This change allows those who do not want to use the verified boot
scheme implemented by vboot as well as its requirement of a more
complex partition scheme designed for chromeos to make use of the
measured boot functionality implemented within vboot library to
measure the boot process.
TODO: Measure MRC Cache somewhere, as MRC Cache has never resided in
CBFS any more, so it cannot be covered by tspi_measure_cbfs_hook().
Change-Id: I1fb376b4a8b98baffaee4d574937797bba1f8aee
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Add an enable reset delay to avoid messages like this in the
kernel:
i2c_hid i2c-WCOM50C1:00: failed to change power setting.
This gets rid of all the warnings except one on reboot/shutdown.
That last case likely isn't fixed because the sleep command is
being sent directly from i2c_hid_shutdown(), so no ACPI routines
get to run and provide the delay. Since the machine is going down
for shutdown/reboot anyway, fixing that last case is a lower
priority.
BUG=b:145094539
TEST=Run on kohaku, switch to guest mode and log out, no errors
Signed-off-by: Evan Green <evgreen@chromium.org>
Change-Id: I8fadf497dd09e5b95b1d74443fb0543d3555dbb8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39707
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
It is not a single mainboard anymore, it's actually three variants.
Change-Id: I66f1239abadd8bf93269d6d4617329dc4b925e8d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Make use of overridetrees, as these mainboards are very similar.
Tested on GA-H61MA-D3V, still works fine.
Change-Id: I1b587a091da631cb172eb76722958da6c7518893
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39668
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3dfa303b6aae2446fa3a1d67a6e31448277cacdb
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
TEST=build with BUILD_TIMELESS=1, binary does not change
Change-Id: I56983cabfad574b970aba098a178e691c6b354d1
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Get ready to squash all the ASUS i440BX boards together.
Change-Id: Ibc9bfa4fc5b582bf658215bda298523e8ee7b36b
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Coalescing is not needed, as root port #1 is enabled. Also, update the
comments to look more like the other two variants. Note that the Intel
H61 PCH only has six root ports, so devices 1c.6 and 1c.7 do not exist.
Change-Id: I3f4bf99ceec6c77f6e1eabea9b712245afee7d34
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39742
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This initial devicetree attempts to correctly configure the status of
each PCI device. Not all required drivers are instantiated, nor are
all of the SoC options fully selected yet.
PCIe root ports are enabled and clocks are assigned.
USB ports are assigned.
BUG=b:150165131
BRANCH=none
TEST=util/abuild/abuild -p none -t google/deltaur -x -a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I911ec08b0db3647d131113a138fb74a55612fd62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
This configuration sets up all of the GPIO pads for the first rev of
the board.
BUG=b:150165131
BRANCH=none
TEST=util/abuild/abuild -p none -t google/deltaur -x -a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4f6398808809492dcb345ccaa09e199fa35e40cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Created a new Google baseboard using Tiger Lake named deltaur, taking
volteer as a starting point.
BUG=b:151102807
TEST=make build successful
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Ib98f328df22f39e7d9d625a3292954881ee15b15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
In order to create a working baseline all ports are being set to have
retimers. Setting the TcssAuxOri UPD to 0 in order for the SoC to not
misconfigure the ports. Volteer will need some additional changes after
this is implemented to account for ports that do not have a retimer.
This setting is in the process of being documented in the TGL EDS and we
can update once it is fully understood what this setting is changing on
the SOC side.
BUG=b:145943811
BRANCH=none
TEST=Boot to OS and check Type-C port1 Display on Volteer,
Connecting Type-c display should work regardless of Type-c cable
orientation.
Change-Id: I29eb0513299126ad8d1ee11ded2c771f28ad13f3
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39460
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the halvor variant of the volteer reference board by copying the
template files to a new directory named for the variant.
BUG=b:151399850
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_HALVOR
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: If4d3417ba55d56af441c99d949a196328d7a1951
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Update the GPE configuration for dw0, dw1 and dw2.
BUG=None
TEST=build and boot tglrvp
Change-Id: I8b406bcbd710e84cec91a8c2d1557902e929f7cc
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39844
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable wifi sar feature and set wifi sar name for kled sku.
BUG=b:152277272
TEST=emerge-hatch coreboot chromeos-bootimage and
verify wifi SAR load by sku-id
Change-Id: I9ee242773fd05cc2bcd7bde07da8176022827677
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Glados boards do not have an exposed serial port outside
of the servo interface. Set board Kconfig so that a default
built image with Tianocore payload is bootable and doesn't
hang due to trying to send data over a non-existant serial port.
Test: build/boot google/chell with board defaults
Change-Id: Ifad6f805e66438e2c436d9fa235d9be2ecf69179
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use it wherever the standard numbers were copied to. Bit 31 is set
at runtime unconditionally, so we don't need it here.
Change-Id: I0d853c3b8250a2c7b2d1a91985a555e4b17ad76c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39731
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Further backport the backlight-PWM handling from Skylake. Beside
configuring the PWM frequency in Hz, we also use the PCH's logic
for the brightness setting via BLM_PCH_OVERRIDE_ENABLE. Linux
would toggle it anyway and that might confuse our ASL code.
We assume that the 183Hz value that was set before for Slippy
variants was overridden by Linux with the 200Hz VBT value, like
it was for the Broadwell Chromebooks. So we set 200Hz for them
in the devicetrees. The calculated value for the T440p of 220Hz
seems sane and also matches the VBT.
Change-Id: I17dfe1a3610d5e2918c617cf5d10896692fdccb3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Cyan has no VGA BIOS available (at least not publicly), so
remove related options. Disable SoC serial output by default,
since no production devices have this exposed, but leave it
as a user option so it can be selected as needed (eg,
for use with a Google debug servo).
Change-Id: Ic079a39ca5ad0ac653b52248244b94d4bfbd08a4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39872
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Chrome-EC/PD images for all glados variants need to be built
from the board-specific branch, not master. Including the default
board names serves no purpose and requires users to deselect
the "use built-in EC firmware" in order for the board to build.
Test: build google/chell with defaults
Change-Id: Ic10f11337b85035068cdc4fe8147413e6b7f57ac
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add missing port definition for the mSATA/WWAN mPCIe port,
set OC pin for internal ports to OC_SKIP, fix port
descrption for mPCIe/WLAN port, remove USB3 definition for
right type-A port as it is USB2 only.
Test: insert WiFi module into WWAN port, observe BT portion
detected and functional.
Change-Id: Ie39b99eeb0f605ff07d57c32189fb1f4183713e4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Create the sushi variant of the hatch reference
board by copying the template files to a new directory named
for the variant.
(Auto-Generated by create_coreboot_variant.sh version 3.0.0).
BUG=None
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_SUSHI
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: Ie900d09ff55e695527eafe68a5a75cd4a0b6d340
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Just a minimal set of board files needed to get it to boot
in 1 CPU mode.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: Ie2f944964e938d8026a6d5d8a22a8449199d08aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Tioga Pass comes with AST2500 BMC which offers SuperIO functionality.
However we currently do not configure/enable SuperIO chip. As a result
system boots pretty silently on cold boot. Then FSP configures SuperIO
and resets the system so on next boot serial console does work. This
makes debugging difficult because pre-FSP output is invisible.
This patch enables bootblock to properly configure desired BMC SuperIO
port so early serial output is visible.
TEST=do a cold boot on OCP Tioga Pass, observe bootblock output starting
from bootblock.
Change-Id: Iff8e6a862858d733f529bb9b8c65e22e5ec6b521
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
|
|
Change-Id: Iad0b394dea017223a5b92fff0cb4c2ed1d5a7bd7
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39402
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1.Select CHROMEOS_EC related Kconfig for variant board with
external EC support.
2.Select proper CHROMEOS Kconfigs which are required for all
variants.
3.Disable Intel EC region in case of external EC.
BUG=None
BRANCH=None
TEST=Compilation is successful for both Jasper Lake RVP variants.
Change-Id: I290b3748777e18476651101de71df9080dd3105c
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39584
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The board version is part of EC's EEPROM, select Kconfig item to enable
requesting the EC for board version.
BUG=b:152374066
TEST=Verified the mainboard version is from EC's EEPROM.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Idd8aceed83439cb500e2b03153e9f8ba93979ee8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Change-Id: Icda241cfac7b428176515d7996a48cb01b1dc976
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39815
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7304b06d7bf34fb7126acfdef811481dc5cba598
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update the icc_max for the GT-Sliced VR domain according to the
hardware design.
BUG=N/A
TEST=build
Change-Id: Ib9f7d77d144a282214e6bda8a4e836873c395487
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39804
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The format for VPD has changed s.t. the first NIC should
always have a zero concat to the end.
Adjust all the respective boards to shift back by one and
adjust drivers/net friends to remove the 'special casing'
of idx == 0.
Background:
https://chromeos.google.com/partner/dlm/docs/factory/vpd.html#field-ethernet_macn
V.2: Fixup a code comment typo while we are here.
V.3: Vary special casing semantics for idx==0 => default mac addr is set.
V.4: Rework to still support the legacy path.
BUG=b:152157720
BRANCH=none
TEST=none
Change-Id: Idf83cc621a9333186dabb668b22c4b78e211930a
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Refactor the code and split it into Xeon common and CPU-specific code.
Move most Skylake-SP code into skx/ and keep common code in the current
folder.
This is a preparation for future work that will enable next
generation server CPU.
TEST=Tested on OCP Tioga Pass. There does not seem to be degradation
of stability as far as I could tell.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I448e6cfd6a85efb83d132ad26565557fe55a265a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39601
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sometimes coreboot needs to compile external code (e.g.
vboot_reference) using its own set of system header files.
When these headers don't line up with C Standard Library,
it causes problems.
Create stdio.h and stdarg.h header files. Relocate snprintf
into stdio.h and vsnprintf into stdarg.h from string.h.
Chain include these header files from string.h, since coreboot
doesn't care so much about the legacy POSIX location of these
functions.
Also move va_* definitions from vtxprintf.h into stdarg.h where
they belong (in POSIX). Just use our own definitions regardless
of GCC or LLVM.
Add string.h header to a few C files which should have had it
in the first place.
BUG=b:124141368
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I7223cb96e745e11c82d4012c6671a51ced3297c2
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39468
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Define a chip option to explicitly soft reset all enabled GPIOs to
default state.
TEST=boot FreeBSD 11.2 on PC Engines apu1, change GPIO configuration
using nctgpio module and check whether GPIOs are reset after reboot
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Iae4205574800138402cbc95f4948167265a80d15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The 2nd COM port's base address defaults to 0x2f8. Current software
for this system expects the port at 0x3e8.
Configure COMB to use 0x3e8 instead of 0x2f8.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: Ibb462bad5f0594e0b5c8dea6e02cd42d58d999ab
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Remove unused SMM_STORE space and use it for RW_LEGACY area
BUG=None
TEST=None
Change-Id: I5724b860271025e8cb8b320ecbd33352ef779660
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
The concerned GPIO is configured as an open drain at the Embedded
Controller side without an external pull-up. This causes leakage in the
PP3300_A rail. So configure the GPIO to have a weak internal pull-up at
the SoC side.
BUG=b:151680590
TEST=Build the mainboard. Ensure that there are no leakages in the
PP3300_A rail.
Change-Id: I5553cf40adb92edc0fecab5c875ec8d72063ba7b
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We should only define function to get lid switch and recovery mode
switches when CHROMEEC_SWITCHES is not available. Correct this to avoid
compilation issues
BUG=None
BRANCH=None
TEST=jslrvp code compilation is fine
Change-Id: I2445d40da1540c9d8c8c5fc845a4f38a5abf983e
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39585
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add memory initialization parameters for Jasper Lake RVP boards
Jasper Lake RVP supports two variants, one with memory LPDDR4
and another with DDR4
Based on board id, mainboard will pass correct memory parameters
to the fsp.
BUG=None
BRANCH=None
TEST=Check compilation for Jasper Lake RVP and check memory training passes.
Change-Id: Idc92363a2148990df16c2068c7986013d015f604
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39195
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The ACPI Spec 2.0 states, that Processor declarations should be made
within the ACPI namespace \_SB and not \_PR anymore. \_PR is deprecated
and is removed here.
Additionally add processor scope patching for P-State SSDT created by
AGESA, becasue AGESA creates the tables with processors in \_PR scope.
TEST=boot Debian Linux on PC Engines apu2, check dmesg that there are
no errors, decompile ACPI tables with acpica to check whether the
processor scope is correct and if IASL does not complain on wrong
checksum, run FWTS
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I35f112e9f9f15f06ddb83b4192f082f9e51a969c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39698
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A bigger than zero value of bmc_boot_timeout must be set
for KCS ipmi_get_bmc_self_test_result() to run, otherwise
the self test result will be error and won't write SMBIOS
type 38 table. Here we set 60 seconds as the maximal self
test timeout.
Tested=Check if the BMC IPMI response data and SMBIOS type
38 on OCP Tioga Pass are correct or not.
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Change-Id: I3678973736a675ed22b5bc9da20a2ca947220f4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Nuvoton NCT5104d has no LDN 0xe according to its datasheet.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I0d34218d88b779b08c380d2396ff9ab9253597fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Enable ASPM L0s and L1, Common Clock and Clock Power Management for
all PCIe ports.
TEST=boot Debian linux and check new PCIe capabilities appear in lspci
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I0a4c83731742f31ab8ef1d326e800dfdc2abb1b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
PC Engines apu2 had many problems with PCIe cards detection. The cards
were inconsistently detected when booted from G3, S5 or after a reboot.
AGESA can reset PCIe slots using GPIO via callback. Use it to reset the
slots that support using GPIO as reset signal.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I8ff7db6ff85cce45b84729be905e6c895a24f6f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The `link_frequency_270_mhz` setting was originally used by the native
graphics init code for Sandy/Ivy Bridge, which is long gone.
The value of this information (which board had it set) is questionable.
The only board that had an LVDS panel and set it to 0 was the ThinkPad
L520, where native graphics init was never reported to work. Also, the
native graphics init only used it for calculations, but never confi-
gured the hardware to use a specific frequency. A look into the docu-
mentation also doesn't reveal any straps that could be used to confi-
gure it.
Change-Id: Ieceaa13e4529096a8ba9036479fd84969faebd14
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39763
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
_DCS, _DGS and _DSS are required by specification. However,
we never implemented them properly, and no OS driver com-
plained yet. So we stub them out and keep the traditional
behavior in case an OS driver checks for their existence.
The old implementations also only returned static values as
there never was any write to their GNVS variables. The TRAP()
that was called in one place is actually implemented by some
ThinkPad's SMI handler as docking event. However, as the call
precedes these SMI handlers in coreboot history, it's most
likely an accident.
Change-Id: Ib0b9fcdd58df254d3b2290900e3bc206a7abd92d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
The format for VPD has changed s.t. the first NIC should
always have a zero concat to the end. drivers/net supports
this with the workaround of setting the idx to 1.
The longer term fix is to adjust all the respective boards
to shift back by one and adjust drivers/net friends to
remove the 'special casing' of idx == 0.
Background:
https://chromeos.google.com/partner/dlm/docs/factory/vpd.html#field-ethernet_macn
BUG=b:152157720
BRANCH=none
TEST=none
Change-Id: I510428c555b92398a5199b346dffb85d38495d74
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39768
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I385339761b3e1b5dcadb67b8ca29b1518c2db408
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The ACPI Spec 2.0 states, that Processor declarations should be made
within the ACPI namespace \_SB and not \_PR anymore. \_PR is deprecated
and is removed here for Intel CPUs only.
Tested on:
* X11SSH (Kabylake)
* CFL Platform
* Asus P8Z77-V LX2 and Windows 10
FWTS does not return FAIL anymore on ACPI tests
Tested-by: Angel Pons <th3fanbus@gmail.com>
Change-Id: Ib101ed718f90f9056d2ecbc31b13b749ed1fc438
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
A certain somebody (that would be me) forgot how to count, it seems.
Change-Id: Iac0ac5827ca242c465a2e8be92a823c8fc9b2935
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39741
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Coalescing is not needed, as all PCIe ports are used.
Change-Id: Icf31f6672e0a54d119a6537da1b52c42f9cee823
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39740
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
IRQ 0x70 was not declared for device 2e.7, and coreboot whined about it.
Change-Id: If40aa390722cf253169003129b31f20543fde5dd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39739
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Linux does not handle either value in any special way, though.
Change-Id: I833cb94e65b9ddfb79edbcdd0216c70740aa4a16
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add camera ACPI configuration for Ripto/Volteer
BUG=None
BRANCH=None
TEST=Build and boot Ripto or Volteer. Start camera app and able to
capture images.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I2b47ccd989192273a29f09bf097e12e357929334
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39684
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
This is required for PD notifications on the cros_ec driver.
BUG=b:150649744
TEST=Boot volteer with this patch and verify that PD notifier events are
being generated.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Change-Id: I2e72320b025a3dfa7412181586cb142a4503eda5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use information provided by AGESA to fill the SMBIOS memory tables.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Id73de7c2b23c6eb71722f1c78dbf0d246f429c63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Update Audio AIC UPD settings and gpio pad configs for Tiger Lake.
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I45935b79f6fa4ad66238eead9258a4f15feec508
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39466
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Camera ACPI had an incorrect board config flag for TGL-UP4.
BUG=None
BRANCH=None
TEST=Build and boot TGLRVP-UP3 or UP4. Start camera app and able to
capture images.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Ided0e146a9240169d3f1f27a86218ac1a942b899
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Micron memory part uses SPD Index 0.
BUG=b:152005386
TEST=Build the mainboard.
Change-Id: I990a95b13d636148f0f922fd5c6d4e489d35ed2c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I487fb53bb2b011d214f002fc200ade2f128a4cc6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
1. Configure Audio GPIOs.
2. Set i2c4 configuration.
3. Update PCH HDA configuration
TEST=Verify codecs gets listed with aplay -l command.
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Change-Id: Ic0516c7a8fee79ce17343a7f42895d6ef534fec9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add HID field in max98357a_config and allow mainboards to set it.
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I22d2d078a9a4eb6ab330da8439737ff5133086d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39286
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I005bf205142d4d8c5e12378f33d2100d278fa174
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I78f06b54a6a03d565cf86f1d7bdf37965c3f6ad0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
They are already in AUTHORS.
Change-Id: I315c0c57babfa239e3d7c501a4183b8996999e6e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Updating devicetree to enable ELAN touchpad and ELAN touchscreen on nightfury
BUG=none
BRANCH=firmware-hatch-12672.B
TEST=built and verified touchpad and touchscreen worked
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Change-Id: Ieba6558ce3897ce2f95f51ed667465d84b4ab189
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The VGA port has the DDC on port B.
Select the correct Kconfig and fix graphics init failing on VGA.
Tested on HP Z220, libgfxinit reports success and SeaBIOS is displayed
on the connected VGA monitor.
Change-Id: Ie5ec1a2d4606a21e1dc4217ff6fefe5ee35ac543
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is a µATX mainboard with a LGA1150 socket and four DDR3 DIMM slots.
Working:
- All four DIMM slots
- Serial port to emit spam
- Some USB ports
- Integrated graphics (libgfxinit)
- HDMI and DVI
- Intel GbE
- All PCIe ports
- Both PCI ports behind the ASM1083 PCI bridge
- At least one SATA port
- RAM initialization with MRC binary
- Flashing with flashrom
- S3 suspend/resume
- Rear audio output
- VBT
- SeaBIOS to boot Arch Linux
Not working:
- PS/2 keyboard (detected as mouse)
Untested:
- The other audio jacks
- S/PDIF
- VGA
- EHCI debug
- Front USB headers
- Non-Linux OSes
- TPM header
- Parallel port
Change-Id: I10a16dfc56f2aa88648c8aaaba4feab40c491504
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36770
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adds GMM into the baseboard of Octopus
For GLK, PCI device 3 is GMM according to
Document#: 569262(Glk EDS Vol-1 rev2-7)
Related to Gerrit review 39579
BUG=b:151115705
BRANCH=None
TEST=Flashed final image on Chromebook
Change-Id: I75b4a835c18c5eeb542b7f7b89deea45a31e47bd
Signed-off-by: Franklin He <franklinh@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The integrated BT is routed via USB2 port 8, add USB configuration
to support integrated BT enumeration.
Change-Id: I46d8c92ba57cd72a91ee15ef4d11f07824c29e9a
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I426518e8e18de1c8efcfb7ecb0835df3e257dca1
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39608
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I09cc279b1f75952bb397de2c3f2b299255163685
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I18e513cefc373b1cd70d31d1159928cc948a8476
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I57fc98788bb47df16d6aedd0f0701e9991801743
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39606
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
* Change power sequence to make it closer to ov8856 sensor
data sheet version 2
* Handle different PWREN GPIO pins for up3 and up4
* Add link frequencies definitions to sensor side
* Clean up format
BUG=None
BRANCH=None
TEST=Build and boot TGLRVP U or Y. Start camera app and able to
capture images.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Ic11a36f1f82fe425c1a5796847ce020007064403
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39529
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Method RAOW is assuming that the first argument is a Field object
and writing to it expecting the register to get updated. However,
the callers are passing in the value of the Field object instead.
This eventually is resulting the IMGCLK not getting enable/disabled on the
platform.
Fix this by sending the exact address of the register to be updated.
Also MCCT was setting the clock frequency in both case i.e, Clock Enable
and Disable. Split the MCCT method in two, MCON and MCOF to fix the sequencing
like below
MCON:
Set frequency
Enable clock
MCOF:
Disable clock
Also, make use of MCON and MCOF methods for camera clock control in tglrvp.
This is to avoid the buildbot marking the patch unstable.
BUG=None
BRANCH=None
TEST=Build and Boot waddledoo board and verified that IMGCLKOUT for
world facing camera is enabled/disabled and able to capture images.
Build and Boot Tiger Lake RVP board and verified that IMGCLKOUT for
world facing camera is enabled/disabled and able to capture images.
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change-Id: I8b886255d5f38819502ae1f4af0851b5a0922b22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39498
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Foob360 would prefer to use different SAR values. Since Foob360
sku id is 9.
BUG=b:149362272
BRANCH=octopus
TEST=build
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I8cc5d73629990f19d2c1044debdba4990c54d07e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
|
|
These platforms use the standard fixed function power button
and do not need a second power button device declared or the
kernel will end up with two devices reporting the same event.
Same change was applied to all google mainboards in
CB:27272 which contains more detail.
Change-Id: I17c85e43493530d04f4fa13f33bec6d027cb3147
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39577
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add initial support for waddledee variant board.
BUG=b:151576904
TEST=Build the mainboard and variant board.
Change-Id: I20d41fbbb78c7fd2f964a97ffebbc9c3bbfb1c5c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39580
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BRANCH=none
BUG=b:145946347
TEST=boot to OS with TGL RVP UP3,
then copied ISH firmware to host file system /lib/firmware/intel/tglrvp_ish.bin
check "dmesg |grep ish", it shows:
ish-loader: ISH firmware intel/tglrvp_ish.bin loaded
cros_ec_ishtp: Chrome EC device registered
Those means shim loader in coreboot has loaded ISH firmware, and
firmware is running successfully.
Signed-off-by: Hu, Hebo <hebo.hu@intel.com>
Signed-off-by: li feng <li1.feng@intel.com>
Change-Id: I1ee8050aef6ec0828f16ef2695b5347278caa820
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39481
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The X210 EC reports battery values in broken mAh. These have to be
adjusted by 10000 * DGVO, as documented in
https://github.com/torvalds/linux/blob/master/drivers/acpi/battery.c.
Taken from https://github.com/harrykipper/coreboot, commits
2f68f138adb25605e5715896636cf33f6de5bd95
c1c72cc43708a6647f263a767c39cf3072908e20
Change-Id: Ie097272443b18b16c3937034f874d3b5a6bdd62a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39142
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Add USB ports for SD card reader, fingerprint reader,
and internal port.
- Enable PcieRpClkReqSupport on NVMe root port,
correct values for ClkReq/ClkSrc.
- Improve comment for M.2-2230 USB port (BT)
Parts derived from x210_test branch of HarryKipper's repo:
https://github.com/harrykipper/coreboot
Change-Id: Ib64629ada4726e5edc080608f71a51f56a9b747c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Derived from x210_test branch of HarryKipper's repo:
https://github.com/harrykipper/coreboot
Test: build/boot x210, test eDP, MiniDP, VGA outputs
Change-Id: Ie2b79b236a458ebd243c992d6e615e41930eeb50
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The 51nb X210 is a replacement motherboard for Thinkpad X200/X201 systems,
based on a modern Kabylake CPU. It also ships with no firmware protection,
(IFD is fully unlocked, no protected regions are set, no Bootguard),
making it an ideal coreboot target. This port is based on the support for
the Skylake-based Purism Librem 13v3, with the following significant
changes:
* EC firmware is contained within the system SPI flash, and so a blob of
EC firmware must be injected to a defined location during image build.
* GPIO layout is different - this is currently just a raw import of the
GPIO configuration from the vendor firmware
* The system has two DIMMs, so an additional SPD address has been added
* The USB port layout is different
* The EC must be enabled at boot time through SuperIO-style logical device
configuration
* EC register layout is different, necessitating changes in the ACPI tables
* The HDA pins are different
* The genx_dec config is different
All hardware appears to work as expected, although the SD reader is
untested.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Change-Id: If74621e76d703f629b54f1feb1acfc95cc72d183
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32531
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This is new Elan touch screen IC, which includes touch panel and USI pen.
BUG=b:151514167
TEST=build bios and verify touch screen works fine
Signed-off-by: Tommie Lin <tong.lin@bitland.corp-partner.google.com>
Change-Id: I98801b8c31812637f71d7eaaa0f12b47901dc47a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The code is for Arrandale CPUs, whose System Agent is Ironlake.
This change simply replaces `nehalem` with `ironlake` and `NEHALEM`
with `IRONLAKE`. The remaining `Nehalem` cases are handled later, as
changing some of them would impact the resulting binary.
Tested with BUILD_TIMELESS=1 without adding the configuration options
into the binary, and packardbell/ms2290 does not change.
Change-Id: I8eb96eeb5e69f49150d47793b33e87b650c64acc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38941
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Consistently use the official uppercase spelling.
Change-Id: I2e2d62389d1b965f4a391080a10e7f97fa787d14
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39350
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable CNVi in devicetree and add gpio pad configs for CNVi
BUG=none
BRANCH=none
TEST=Build and boot tglrvp
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I71146960e0d53dae87946a0365dac6f224a72391
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39464
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Palkia as a variant of Hatch.
BUG=b:150254194
BRANCH=none
TEST=none
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I6a303d9fc2be9ea358ad66cd648738187c974193
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38860
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Volteer uses 4 bits (hardware straps) to indicate what memory
configuration the board is populated with (i.e. which SPD file
to use for the populated memory). This allows for only 16
different SPDs for supporting Volteer and all future variants of
Volteer. Currently, each memory chip needs its own SPD file, so we
can only support 16 different memory chip options for Volteer and
all of its variants.
Generic SPD files are just SPD files that have been stripped down
to contain only fields that are important for the memory controller
(strips out items like vendor info, for example). Using generic SPD
files allows for more than 16 different memory options given it's no
longer a 1-to-1 mapping as similar memory modules from different
vendors can share the same generic SPD file.
BUG=b:147857288
TEST="emerge-volteer coreboot chromeos-bootimage", flash ripto and
verify ripto boots to kernel and "cat /proc/meminfo" reports 8GB
of memory.
Change-Id: I17bd4f4a00b4e3bbaf845d6d321962c11569a186
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39423
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Turn on CNVi device. Turn on PCIe Root port that hosts WLAN device.
Configure PCIe Clk Source and Clk Request mapping. Configure GPIOs used
for WLAN - both CNVi and M.2.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I9bb8e57cdb688bc544929c94af380b9ef1d936a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Disable the BT module in bootblock and enable it in ramstage. This
allows for loading the BT firmware during reboot.
TEST=Build and boot the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I0406a68ffcab2675a1aedb212cb7c8508a5b61fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39446
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable GEO SAR function.
BUG=b:150347463
BRANCH=drallion
TEST=NA
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Iace9aa0245840328aa13920512747ca7f60e85dd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39467
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
