Age | Commit message (Collapse) | Author |
|
As a part of trying to get our boot time as low as possible, any delays
in the code should try to be refactored out. This removes the 50ms
delay in the WIFI sequence by enabling power and putting the wifi module
into reset in bootblock, then bringing it out of reset in ramstage.
This is significantly longer than the 50ms requirement. The reset GPIO
was already being set high in ramstage, so that code didn't need to be
added.
BUG=b:171513520
TEST=Boot on boards with different module types, WIFI works on both.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I211d3da338ad368d1f011f03cf7d05121c057075
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
1. Config EN_PP3300_SSD (GPP_B2) to gpo
2. EMMC_CLKREQ_ODL(GPP_C1) change to GPP_H11
3. WLAN_PERST_L (GPP_H10) change to GPP_H10
BUG=b:172630765, b:171467336
BRANCH=volteer
TEST=emerge-volteer coreboot chromeos-bootimage and boot into emmc
Change-Id: I9d112373c4ecd2cea5ce3d2d47b190c061d50da6
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47705
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Genesys GL9763E as PCI-to-eMMC bridge.
BUG=b:171467336
BRANCH=volteer
TEST=emerge-volteer coreboot
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I858c12151df5b6fc19132869317edfa1b090335d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Currently, the PCIe bridge 00:15.2 is not detected by coreboot, causing
the connected network device also to be missing.
This is caused by not configuring the third of the four PCIe General
Purpose Ports (GPP) of the AMD Fusion Controller Hub (FCH), which can be
exposed as one to four PCIe devices.
So, enable it in AGESA but disable enumeration in coreboot. Otherwise,
the serial console stops working in romstage after
[…]
PCI: 00:15.1 bridge ctrl <- 0013
PCI: 00:15.1 cmd <- 06
PCI: 00:15.2 bridge ctrl <- 0013
PCI: 00:15.2 cmd <- 07
and the system hangs in the payload (SeaBIOS banner is shown on VGA
attached monitor).
TEST=Serial console and payload works, and Linux 5.10-rc2 configures
PCIe bridge. Output of `lspci -t`:
-[0000:00]-+-00.0
+-00.2
+-01.0
+-01.1
+-10.0
+-10.1
+-11.0
+-12.0
+-12.2
+-13.0
+-13.2
+-14.0
+-14.2
+-14.3
+-14.4-[01]--
+-14.5
+-15.0-[02]--
+-15.1-[03]----00.0
+-15.2-[04]----00.0
+-18.0
+-18.1
+-18.2
+-18.3
+-18.4
\-18.5
Change-Id: Ia1d60a212b0d249c7d8b3f8ec16baf5e93c985da
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46527
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Working:
- TianoCore
- NVMe, SATA3
- USB2, USB3
- Thunderbolt
- Graphics (GOP and libgfxinit)
- Sound
- Webcam
- WLAN, LAN, Bluetooth, LTE
- Keyboard, touchpad
- TPM
- flashrom support; reading / flashing from Linux
- ACPI S3
WIP:
- Documentation
Not working:
- EC ACPI (e.g. Fn keys, battery and power information)
Boots Arch Linux (Linux 5.8.12) successfully.
Change-Id: I364f5849ef88f43b85efbd7a635a27e54d08c513
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The auxadc (auxiliary analogue-to-digital conversion) is a unit
to identify the plugged peripherals or measure the temperature
or voltages.
The MT8183 auxadc driver can be shared by multiple MediaTek SoCs
so we should move it to the common folder.
Signed-off-by: Po Xu <jg_poxu@mediatek.com>
Change-Id: Id4553e99c3578fa40e28b19a6e010b52650ba41e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Change-Id: Ic3ed97fc2b54d4974ec0b41b9f207fe3d49d2cce
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/25436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
A new field was defined for different keyboard layouts, so add this field
to the list and provide the two options that were defined.
Change-Id: Ic357446725e34221040705929d54cbce94c5ab8b
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Set the default state of the TCSS PCIe RP0 to hidden so that coreboot
does not allocate resources to this hotplug root port. The default
behavior on the reference design is that there is only one USB4 port
attached to port C1 while port C0 is only a USB3 port.
Meanwhile the Voxel and Terrador variants do have USB4 on both C0 and
C1 ports, so these boards change the default to 'on' so that coreboot
does allocate resources for the hotplug port.
BUG=b:159143739
BRANCH=volteer
TEST=build volteer and voxel and check the resulting static.c to
ensure the device is hidden or not. Also boot with the two different
configurations and ensure resources are assigned or not. Finally
check that S0ix still functions with the C0 port set to 'hidden'
after authorizing a PCIe tunnel on port C1.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I8bb05ae8cd14412854212b7ed189cfa43d602c1d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47198
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is an issue with the storage device being mis-detected on exit
from S0ix which is causing the root device to disappear if the power
is actually turned off via RTD3.
To work around this read the RX state of the pin and apply the IOSSTATE
setting to drive a 0 or 1 back to the internal controller. This will
ensure the device is detected the same on resume as on initial boot.
BUG=b:171993054
TEST=boot on volteer with PCIe NVMe and SATA SSD installed in the M.2
slot and ensure this pin is configured appropriately. Additionally
test with PCIe RTD3 enabled to ensure suspend/resume works reliably.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I85542151eebd0ca411e2c70d8267a8498becee78
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable the PCIe RTD3 driver for the PCIe attached SD card interface
and provide the enable/reset GPIOs. These GPIOs are common across
all variants so this is implemented in the baseboard devicetree with
an fw_config probe if the device is present. The RTS5261 device
does not have an enable GPIO so it is disabled in a workaround in
mainboard.c, along with marking the SD-Express device as external.
BUG=b:162289926, b:162289982
TEST=Tested on Delbin platform to ensure the system can enter the
S0i3.2 substate and suspend/resume is stable.
enabling this for the regular Genesys
Change-Id: I40fe05829783c7bce2a2c4c1520a4a7430642e26
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable Runtime D3 for the volteer variants that have GPIO power control
of the NVMe device attached to PCIe Root Port 9.
Enable the GPIO for power control for variants that do not already have
it configured to allow the power to be disabled in D3 state.
BUG=b:160996445
TEST=tested on delbin
Change-Id: I6ebf813c6c3364fec2e489a9742f04452be92c45
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46262
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Replace the two obsolete LPID implementations with the new PEPD device.
The PEPD device gets included in the plaforms' `southbridge.asl`, since
it is required to load the `intel_pmc_core` module in Linux, which
checks for the _HID. (See CB:46469 for more info on that.)
There is no harm for mainboards not supporting S0ix, because the _DSM
function won't be called with the LPS0 UUID on such boards. Such boards
can use the debugging functionality of `intel_pmc_core`, too.
Change-Id: Ic8427db33286451618b50ca429d41b604dbb08a5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46471
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename LPID to PEPD for consistency. PEPD means "Power Engine Plug-In
Device" and is the name Intel and vendors usually use, so let's comply.
Change-Id: I1caa009a3946b1c55da8afbae058cafe98940c6d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46470
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO 86 should be set high on boot to save power.
BUG=b:173340497
TEST=Build only
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I31ef1d2a1967d82ba5370462783a909417088d2f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The GPP_F16 is for enable_gpio after check the schematic.
BUG=b:151978872
TEST=FW_NAME=terrador emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I63f43c231e624ed034ef18e8f06942ff3622d821
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Extend the Kconfig option text of L140CU with L141CU since the hardware
of both is equal.
Change-Id: If0e5061fc345208688a678a4cdf7c5ecaf47c17d
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I531865416b1bf9c5a73c809590059e7d7c8f373a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47715
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Volteer has a new Audio option in FW_CONFIG. This patch adds
support for it and when enabled, programs GPIO pins for I2S
functionality.
BUG=b:171174991
TEST=emerge-volteer coreboot
Change-Id: I85bc37980957a3fb6c795858a4e4f44f3e3cc332
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Ambassador is similar to puff. This change matches the
PcieRpSlotImplemented configuration with Puff's, originally made for
Puff in https://review.coreboot.org/c/coreboot/+/39986.
Signed-off-by: Matt Ziegelbaum <ziegs@google.com>
Change-Id: I5b6246f58c10e03a0d02278ad3621ded39bb6d6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fan table: provided by the ODM (see attachment in bug) based on
measurements with EVT unit.
BUG=b:173134210
TEST=flash to DUT
Change-Id: I9f727f0f7e2eb7fe70385ebc843558d51e1860c5
Signed-off-by: Matt Ziegelbaum <ziegs@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
HPD_1: A19 -> E14
HPD_2: A20 -> A18
Change-Id: Idf3c8f4931bf8364bb9216a9369df7e05dcde047
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Configure the pins for SD to msdc1 mode and change the driving
value to 8mA. Enable VCC and VCCQ power supply for SD.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: I11151c659b251db987f797a6ae4a08a07971144b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
SD Card driver needs to access two regulators - MT6360_LDO5 and
MT6360_LDO3. These two regulators are disabled by default.
Two APIs are implemented:
- mainboard_enable_regulator: Configure the regulator as enabled/disabled.
- mainboard_regulator_is_enabled: Query if the regulator is enabled.
BUG=b:168863056,b:147789962
BRANCH=none
TEST=emerge-asurada coreboot
Change-Id: I391f908fcb33ffdcccc53063644482eabc863ac4
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46687
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, five regulator controls are implemented for DRAM
calibration and DVFS feature.
The regulators for VCORE and VM18 are controlled by MT6359.
The reguatlors for VDD1, VDD2 and VMDDR are controlled by MT6360
via EC.
BUG=b:147789962
BRANCH=none
TEST=verified with DRAM driver
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Id06a8196ca4badc51b06759afb07b5664278d13b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
MT6359P is a PMIC chipset for Mediatek MT8192 platform.
Reference datasheet: MT6359_PMIC_Data_Sheet_V1.5.docx, RH-D-2018-0205.
BUG=b:155253454
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I62f69490165539847b8b7260942644533b15285b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45399
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current CSE firmware update implementation adds CSE RW binary to
FW_MAIN_A/B and this increases the boot time due to the size increase
of these regions leading to higher loading and hashing time.
To mitigate this issue, CSE RW binary is moved from FW_MAIN_A/B to new
region, ME_RW_A/B under RW_SECTON_A/B, and this updates the flashmap to
add ME_RW_A/B region for CSE RW binary.
BUG=b:169077783
TEST=build with cse rw binary, flash and verify volteer2 boots to OS.
Verify me_rw binary is added to ME_RW_A/B region.
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Change-Id: I87da3824933ed2dd8e8ed0fed8686d2a3527faea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46431
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch modifies flash layout to add ME_RW_A/B to add
the CSE RW blob and also enable the CSE RW update feature for
JSLRVP
BUG=b:169077783
TEST= Built for jslrvp. Verified that CSE RW and metadata files
are included in cbfs.
Change-Id: I13baa317a06d00cec0337f08754892c7c8737f5d
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Existing implementation adds the CSE RW update binary to FW_MAIN_A/B
regions and this has significant impact on boot time due to the
increase in the size of these regions leading to higher loading
and hashing time.
This patch modifies flash layout to add new ME_RW_A/B fmap regions
in the RW_SECTION_A/B.
BUG=b:169077783
TEST= Built for dedede. Verified that CSE RW binary is added to the
CSE_RW_A/B fmap region.
Change-Id: I23a3e22a569488b39beb4d12f5b6309c7c742992
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add Elan and Goodix touchscreen settings.
BUG=b:169813211
BRANCH=None
TEST=build metaknight firmware
Change-Id: Ib2acd31a8076533c3b927d37127e7d27bac0bb57
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
When the system shuts down, turn the fingerprint sensor off. This sets
the GPIOs correctly for the next boot. The fingerprint sensor was
previously left on, and was just powering down when the rails went low.
On suspend, the fingerprint sensor stays awake and puts itself in a low
powerstate mode based on the SLP_Sx_L pin states.
BUG=b:171837716
TEST=Fingerprint sensor still works after S3, GPIO state on the boot
following a shutdown is low.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I3837b58372d8f4a504535e76bd21c667d68f8995
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47311
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
"Die()" needs <console/console.h>.
Change-Id: I250988d77b0b0a093a1d116bea44a0cbb84189dd
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
"printk()" needs <console/console.h>.
Change-Id: Iac6b7000bcd8b1335fa3a0ba462a63aed2dc85b8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
BUG=b:172843935
BRANCH=coral
TEST=emerge-coral coreboot chromeos-bootimage
Signed-off-by: James Chao <james_chao@asus.corp-partner.google.com>
Change-Id: I70195acc33218d3ad4c77acfdbc8f6ed93ab144e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47382
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
At this point, the zork platform will only use psp_verstage, so remove
the VBOOT_STARTS_IN_BOOTBLOCK option and set code for VBOOT_STARTS-
BEFORE_BOOTBLOCK to always be used.
TEST=Build & Boot Morphius
BRANCH=Zork
BUG=b:172848137
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I30d90fe82c37966a860b52c07a3550dcecf8d19d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47529
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The current I2C2 bus frequency is 344 kHZ, which does not meet the spec. This change updates scl_lcnt, scl_hcnt, sda_hold value for I2C2 to bring
the bus frequency closer to 400 kHz.
BUG=b:153588771
TEST=Verified that I2C2 frequency is 380 kHz.
Signed-off-by: Johnny Li <johnny_li@wistron.corp-partner.google.com>
Change-Id: I96fa5ed586de41324733ac7537b6bd73f39fc176
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47558
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add G2Touch touchscreen support for bobba.
BUG=b:171636614, b:169730666
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage, and check touchscreen
work.
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ia361a56c050d7cbd7325b3c09fc34d8707441cc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add information regarding the privacy pin on the overridetree and gpio.
BUG=b:172807539
Change-Id: Ic1bfa63e35a16d71a26adc3ec07b1ba36e6dc168
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47362
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I50390f66d9570eb0fd703e3ad8a2735125d76b61
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47566
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the lantis variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:171546871
BRANCH=dedede
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_LANTIS
Change-Id: Ie3d15a687b870afc7d8bbeb6b5cab0792650da31
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
WRDD table is needed for Intel WiFi module to enable SAR function.
BUG=b:173066178
BRANCH=zork
TEST=dump ACPI and check WRDD exist with Intel WiFi module.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I9fd6fd19ed188f7ab91faab9e2599b9b09ca5b22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47554
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Amanda Hwang <amanda_hwang@compal.corp-partner.google.com>
|
|
1. Enable panel stop GPIO in ramstage
2. generic.reset_delay_ms change to 30
BUG=b:171365316
Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Change-Id: I90ca39312252c668da6298183e598392bc9f9f28
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
Add a function that initializes GPIOs based on the sleep type that
the system is coming back from. This allows initialization of the
fingerprint GPIOs which need to be handled differently between wake
from S3 and boot from S5.
On initial boot, the state of the FP sensor could be either
enabled or disabled. Because of this, on boot, we power off
the sensor for >200ms, to reset its state, then power it back on.
In suspend/resume, the fingerprint sensor should remain powered
the entire time.
If fingerprint is disabled on the trembyle-based board, set the pins
to no-connect. Dalboz doesn't have fingerprint and the GPIOS are
configured differently due to the FT5 chip having fewer GPIOS than
FP5, so nothing needs to be initialized there.
There were also a couple of trivial comment clean ups regarding the
FPMCU GPIOS.
BUG=b:171837716
TEST=Boot & Check GPIO states.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I16a2e621145782e0a908bb3e49478586c09a0e0a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds memory parts used by variant voema to
mem_parts_used.txt and generates DRAM IDs allocated to these parts.
Added memory
1. H9HCNNNCRMBLPR-NEE
2. H9HCNNNFBMBLPR-NEE
3. MT53D1G64D4NW-046 WT:A
BUG=b:172751925,b:172781673,b:172782100,b:172781562
TEST=emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ic832155448fb07152b906aa04ca49d384ec47b34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47351
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The T3 that PPVARN_LCD low to LCM_RST_1V8 high is 0.1269ms and
it does not meet the LCD specification that the T3 must be larger
than 5ms. Because there is a delay between PPVARN_LCD_EN and
PPVARN_LCD. An extra 9ms delay should be added on LCM_RST_1V8
in order to meet the specification "ProductSpec_NV105WUM-A51_
V4.3_P2(TLCM).pdf".
BUG=b:172201138
BRANCH=kukui
TEST=The LCD sequence T3 is larger than 5ms when power on.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Iaf7ae494e30c4c207103d949287b335288688c54
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Currently the decision of whether or not to use mrc_cache in recovery
mode is made within the individual platforms' drivers (ie: fsp2.0,
fsp1.1, etc.). As this is not platform specific, but uses common
vboot infrastructure, the code can be unified and moved into
mrc_cache. The conditions are as follows:
1. If HAS_RECOVERY_MRC_CACHE, use mrc_cache data (unless retrain
switch is true)
2. If !HAS_RECOVERY_MRC_CACHE && VBOOT_STARTS_IN_BOOTBLOCK, this
means that memory training will occur after verified boot,
meaning that mrc_cache will be filled with data from executing
RW code. So in this case, we never want to use the training
data in the mrc_cache for recovery mode.
3. If !HAS_RECOVERY_MRC_CACHE && VBOOT_STARTS_IN_ROMSTAGE, this
means that memory training happens before verfied boot, meaning
that the mrc_cache data is generated by RO code, so it is safe
to use for a recovery boot.
4. Any platform that does not use vboot should be unaffected.
Additionally, we have removed the
MRC_CLEAR_NORMAL_CACHE_ON_RECOVERY_RETRAIN config because the
mrc_cache driver takes care of invalidating the mrc_cache data for
normal mode. If the platform:
1. !HAS_RECOVERY_MRC_CACHE, always invalidate mrc_cache data
2. HAS_RECOVERY_MRC_CACHE, only invalidate if retrain switch is set
BUG=b:150502246
BRANCH=None
TEST=1. run dut-control power_state:rec_force_mrc twice on lazor
ensure that memory retraining happens both times
run dut-control power_state:rec twice on lazor
ensure that memory retraining happens only first time
2. remove HAS_RECOVERY_MRC_CACHE from lazor Kconfig
boot twice to ensure caching of memory training occurred
on each boot.
Change-Id: I3875a7b4a4ba3c1aa8a3c1507b3993036a7155fc
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46855
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update I2C address for Goodix touchscreen and add ELAN touchscreen &
Synaptics trackpad device. Follow CB:47415 to correct HID over I2C
device to be level triggerd.
BUG=b:160013582
TEST=emerge-volteer coreboot and check system dmesg and evtest can get
device.
Change-Id: I070fb0e06b588f128253270502c9c2c427c62b84
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The option `HeciEnabled` was partly replaced by use of the device on/off
state in the devicetree in commit 3de90d1. The option has been removed
from the corresponding boards, so `HeciEnabled` is always 0 and ME
always gets disabled during soc finalize, when `HECI_DISABLE_USING_SMM`
is set.
Replace the option in the finalize function by the same dt state check
that sets the FSP option and drop the remaints of `HeciEnabled`.
Devicetrees still having `HeciEnabled` have been adapted to keep the
current behaviour.
Change-Id: Ib4cca9099b9aa3434552a41fbafca7cf6a0dd0eb
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47195
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
WWAN_RST#: E10 -> F14
WWAN_PWR_EN: E13-> F21
Change-Id: I7182f384eb7a404dfe623c64e29467b41c6b0bdd
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47519
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Select `PM_ACPI_TIMER_OPTIONAL` to enable the new PM ACPI Kconfig and
set the FSP option for PM ACPI timer enablement from its value instead
of using the old devicetree option.
Also drop the obsolete devicetree option from soc code and from the
mainboards and add a corresponding Kconfig entry instead.
Change-Id: I10724ccf1647594404cec15c2349ab05b6c9714f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45955
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix build errors, since `haswell.asl` was dropped in commit 79e3a1f8a5
(nb/intel/haswell/acpi: Merge `haswell.asl` into `hostbridge.asl`)
Change-Id: Iaec5de2d74dd81c58a581bb511ba6a63629141aa
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47575
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I5b6191d2b5f6fd6d127934eda56e3c24181b0c4c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47565
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Idefc15fec1d62d68d88e91c76f59e1a60a3996b6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47564
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of relying on mainboards to call it, do like Lynx Point.
Change-Id: Idb7457e0734e19d0a26f0762079e273b6e740475
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46793
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It is identical for all Broadwell mainboards, thus deduplicate it.
Change-Id: I74559fbe42e44aa4d15ced5d88f6c15a1bf5203b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46792
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, Google Wolf remains identical.
Change-Id: I710581156937b042ba4cf5948c65d0795ad37bbf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46789
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename it to `hostbridge.asl`, which is what Haswell uses.
Change-Id: I6f97fc5c9459fe6b66dcfcf51900c751beda0ebe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46786
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: Ifc6dd5f6549e7501f350afe8456a9a8096edcc25
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: Ida1b1d05b39e67a9eba3bfaecca37f38821a438b
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: Ib2f203b5f5eea5c25cfd4543f5ed9f15101b1735
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: Ic334816712370da63471135da8dd598ab02d54ef
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: I75a92616f11054993ff5a5bfefce5c3f4638c07c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: Iff00667377eecedcf0b83bcfc0bf50bd4c3411eb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: I1773973f64bcc5ef6bd1856c5d8eb998bb6a4888
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: I320198d56131cf54e0f73227479f69968719b2a7
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: Ie7b82ea07ef97b2096d75229c445bd3a65cb3be0
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=emerge-dedede coreboot
Change-Id: I9d8fa57ae0f554896a4a0722e3e89567676382d4
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable USB2 port 5 for user facing camera.
Enable USB2 port 6 for world facing camera.
BUG=b:169813211
BRANCH=None
TEST=build metaknight firmware
Change-Id: Iecb7787d46eab7096dec9f838a16da101105e09a
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Disable I2C port 3 for metaknight
BUG=b:169813211
BRANCH=None
TEST=build metaknight firmware
Change-Id: Ic4a056d53a8c8abd04a9b786428da0986a255276
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The existing help text wasn't updated for Mandolin after it was copied
from an older reference board and contained some information that
doesn't apply to Mandolin.
Change-Id: Ib34abb2ee8b289df5f7085957042fe00ad506ca9
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: If8d3ebdb9a41330312c26fb5796c07de1b87b3eb
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47480
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add CMOS layout and defaults files and enable CMOS options in Kconfig.
Test: changed loglevel setting, rebooted and checked the log.
Change-Id: Ia1a27818b2d12fb7578189e5748b8073c8f928e3
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46311
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It’s common to annotate the closing endif, so do it for these four
files.
Change-Id: Ia5d071e1f544c9dea5af9c6bc3c605d9a0c5c0f5
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Work on this mainboard was abandoned and never finished. It's not really
usable in its current state, so let's get rid of it.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I4cd2e2cd0ee69d9846472653a942fa074e2b924d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change switches the selection of CAR mode so that
INTEL_CAR_NEM_ENHANCED_V2 is the default unless mainboard
selects INTEL_CAR_NEM. INTEL_CAR_NEM is selected only by
mainboards using older silicon (ES1 or ES2) that did not
support NEM enhanced mode.
This enables NEM Enhanced Mode for TGL-U/Y RVPs.
Bug=b:171601324
BRANCH=volteer
Test=Build coreboot for volteer. Boot on SKU that has 4MB L3 cache.
Change-Id: Ib6e041261cb8ca9c6e602935da4962aac0d9ece5
Signed-off-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Commit 8084b38568 (sb/intel/lynxpoint/sata: Always use AHCI mode)
dropped the devtree option, but missed this recently-added mainboard.
Change-Id: I6ab3a763c0bcd7431193c48e473639589b1a1e1a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The other two modes are not used by any mainboard, and the code seems to
be copied from older southbridges. As the code looks incorrect, drop it.
Change-Id: I374546279a85cead1aea13e0952bbfd6f643a75b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The Asus F2A85-M, F2A85-M LE and F2A85-M PRO all have a Super I/O, and
therefore have legacy devices like a serial console.
Selecting `HUDSON_LEGACY_FREE` currently disable the serial console
during bootup in romstage, which is undesired.
So, deselect the symbol by default.
TEST=Boot Asus F2A85-M PRO and verify serial console is *not* disabled
during romstage.
Change-Id: Ia6588c0d4b2c24c7cb9da04805d13274c8ae295e
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47363
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Mike Banon <mikebdp2@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the shuboz variant of the zork reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:172021093
BRANCH=none
TEST=emerge-zork coreboot
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I3f62625f8cbde1c9adf8ab335edeb9e811e32679
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47152
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The code is based on autoport, with necessary modifications.
This laptop uses SMSC MEC1322 embedded controller, but the EC
interface is the same as the EliteBook laptops of previous generations
that use KBC1126 EC. So it still uses ec/hp/kbc1126, but does not need
EC firmware inserted into CBFS. We also need to leave the end of the
OEM flash content untouched, so the default ROM size is set to 12MiB
instead of 16MiB, and we need to modify the IFD when flashing.
Thanks to persmule for providing the laptop and pointing out how to
program the system flash chip of it.
Change-Id: I2328c43cbb1f488aa1d0ddd9116814d971e5d8ae
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45578
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Adds ACPI properties for WDT8762A device.
Per spec v0.8
HID name WDHT2002
T14=100ms
BUG=b:163561649
BRANCH=puff
TEST=emerge-puff coreboot and check system dmesg and evtest can get device.
Change-Id: I178e9d5aa1e1501d33b3cd4092f3f522bb6f1a74
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Hook up PCH thermal subsystem configuration to devicetree.
Change-Id: I84bac2cec079370370ecf1e5e4742e6704921d40
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The X86 Qemu targets use the AMD64 SMM save state, but unlike
most AMD CPU's the PM ACPI SMI port is not configurable and uses
the Intel default APM_CNT, 0xb2 port.
This will be used by the common save state handler.
Change-Id: Ifee9476f628a2df710fb4340ce6a19b008df1033
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45814
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The patch replaces if-else-if ladder with switch case for readability
purpose.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I268db8bc63aaf64d4a91c9a44ef5282154b20a53
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47054
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the genesis variant of the puff reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:172620124
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_GENESIS
Signed-off-by: Matt Ziegelbaum <ziegs@chromium.org>
Change-Id: I70886c2c5a25f5de1a4941ff235547ee812fa50d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
This patch adds the PMC MUX and CONx devices for adlrvp. Device
specific method contains the port and orientation details used
to configure the mux.
BUG=b:170607415
TEST=Built and booted adlrvp. Verified the PMC.MUX CONx objects
in SSDT tables.
Change-Id: I3b5bb73991feb99577c16fea00c381dd0f855769
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Add Kconfig entries, and update existing documentation to
accomodate both v1/v2 versions of the board.
Change-Id: I856bb914941211cfbec4fed871ba2a5a038e23c3
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46984
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct USB over-current mappings in devicetree now that the
GPIO config has been fixed per schematics.
Change-Id: I564630231933c7c17a2c0a2a403fdcca9189b92e
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The LAN NIC is onboard, not installed in a slot.
Change-Id: I77ee7ee8c944b7942ca78d35cd881277c4030ab9
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add strings for M.2 keying and number of PCIe lanes.
Change-Id: I2e13749b50263ee5c2388a419bc8d784af6bd880
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47251
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct PCIe clock source mapping in devicetree now that the GPIO
config has been fixed. Move ClkSrcUsage/ClkSrcClkReq registers
under their associated PCIe root ports.
Change-Id: Ibdaba51d971a39a6da6df82652b7420d7324dee5
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
- set pads GPP_B6/B8 for PCIe CLK_REQ lines
- set pad GPP_B14 to speaker output
- adjust comment for GPP_C22 / USB3_P1_PWREN
- set pad GPP_E4 to NF1 / SATA_DEVSLP0
- set pads GPP_E9/E10 to USB2_OC0#/USB2_OC1#
Change-Id: I8bf8af620370ec2d4c864e513db5d710a9c65d27
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47220
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add information regarding the privacy pin on the overridetree and the
gpio.
BUG=b:171888751
Change-Id: I1ab19a863715ba5a928dd7c16402d398e5475edc
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add information regarding the privacy pin on the overridetree and gpio.
BUG=b:169840271
Change-Id: Ifa628dda03f3f65976850aeabaf516f528a921b7
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update Power Limit2 (PL2) minimum value to the same as maximum value
for magolor board. DTT does not throttle PL2, so this minimum value
change here does not impact any existing behavior on the system.
BUG=b:168353037
BRANCH=None
TEST=Build and test on magolor board
Change-Id: I74e960de506d366cba2c8aefb23f9e69337fd163
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
LTE module used in boten has a specific power on/off sequence.
GPIOs related to power sequnce are:
* GPP_A10 - LTE_PWR_OFF_R_ODL
* GPP_H17 - LTE_RESET_R_ODL
1. Power on: GPP_A10 -> 20ms -> GPP_H17
2. Power off: GPP_H17 -> 10ms -> GPP_A10
3. Warm reset: Power off -> 500ms -> Power on
Configure the GPIOs based on these requirements.
BUG=b:163100335
TEST=Build and boot Boten to OS. Ensure that the LTE module power
sequence requirements are met.
Change-Id: Ic6d5d21ce5267f147b332a4c9b01a29b3b8ccfb8
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Peichao Wang <pwang12@lenovo.corp-partner.google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This support is required to power off certain components that exist only
in certain variants.
BUG=None
TEST=Build and boot Boten to OS.
Change-Id: Ib43ada784666919a4d26246a683dad7f3546fabb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Peichao Wang <pwang12@lenovo.corp-partner.google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds memory parts used by variant voema to
mem_parts_used.txt and generates DRAM IDs allocated to these parts.
Added memory
1. MT53E512M64D4NW-046 WT:E
2. MT53E1G64D8NW-046 WT:E
BUG=b:171755775
TEST=emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I24d466f92a7e0fa3ab2f6241f0b5af025c53ed98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
This patch makes Atlas resume from S0ix by AC plug and unplug.
BUG=b:165328935
BRANCH=atlas
TEST=Put Atlas in suspend. Wake it up by AC plug.
TEST=Put Atlas in suspend. Wake it up by AC unplug.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Change-Id: I95676d785bfc1488a8c1bdd3d56f2c38d95f3fb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
EEPROM in the camera module does not require any specific power
resources. This will ensure that no unnecessary resources are turned on
while accessing the camera EEPROM.
BUG=b:167938257
TEST=Build and boot to OS in Drawlat. Ensure that the camera EEPROM is
listed in the output of i2cdetect.
Change-Id: Iece9b3f657bf94a21cc08bf1745353575858f9b2
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|