summaryrefslogtreecommitdiff
path: root/src/mainboard
AgeCommit message (Collapse)Author
2018-11-12siemens/mc_apl3: Disable PCI clock outputs on XIO bridgesMario Scheithauer
On this mainboard there are legacy PCI device, which are connected to different PCIe root ports via PCIe-2-PCI bridges. This patch disables the unused PCI clock outputs on the XIO2001 PCI Express to PCI Bridges. Change-Id: I2212c1080b72a656b5c8e68b040108a7adbec608 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/29549 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2018-11-12siemens/mc_apl3: Set Full Reset Bit into Reset Control RegisterMario Scheithauer
This mainboard provides customer hardware reset button. A feature of this button is that it holds the APL in reset state as long as the reset button is pressed. After releasing the reset button the APL should restart again without the need for a power cycle. When Bit 3 in Reset Control Register (I/O port CF9h) is set to 1 and then the reset button is pressed the PCH will drive SLP_S3 active (low). Change-Id: Ib842f15b6ba14851d7f9b1b97c83389adc61f50b Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/29530 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2018-11-12siemens/mc_apl3: Set bus master bit for on-board PCI deviceMario Scheithauer
There is an on-board PCI device where bus master has to be enabled in PCI configuration space. As there is no need for a complete PCI driver for this device just set the bus master bit in mainboard_final(). Change-Id: I1ef4a7774d4ca75c230063debbc63d03486fed6f Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/29528 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2018-11-12siemens/mc_apl3: Remove the correction of the Tx signal for SATAMario Scheithauer
For this mainboard the correction of transmit voltage swing from SATA interface is not necessary. Change-Id: I900d0d44b88585c223182d85c78cf3ff1e3e9159 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/29527 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2018-11-12siemens/mc_apl3: Adjust Legacy IRQ routing for PCI devicesMario Scheithauer
On this mainboard there is a legacy PCI device, which is connected to the PCIe root port via a PCIe-2-PCI bridge. This device only supports legacy interrupt routing. For this reason we have to adjust the PIR6 register (0x314c) which is responsible for PCIe device 13h and 14h. This means that the interrupt routing will also be the same for both PCIe devices. The bridge is connected to PCIe root port 2 and 3 over two lanes (Device 13.0 and 13.1). The following routing is required: INTA#->PIRQD#, INTB#->PIRQA#, INTC#->PIRQB#, INTD#->PIRQC# Change-Id: I5028c26769a2122b1c609ad7789c9949e3cb7a87 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/29513 Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-12mb/google/octopus/variants/fleex: Set up tcc offset for fleexJohn Su
Change tcc offset from 0 to 10 for fleex. Refer to b:117789732#1 BUG=b:117789732 TEST=Match the result from TAT UI Change-Id: I481526ab10a16a33fe0cf9528b52b8524e012451 Signed-off-by: John Su <john_su@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29413 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-11-11mb/emulation/qemu-i440fx|q35: Link memory.cPatrick Rudolph
Link memory.c instead of including it. Change-Id: I2bc461b13332ec5885c33c87828a5fd023f8e730 Signed-off-by: Patrick Rudolph <siro@das-labor.org> Reviewed-on: https://review.coreboot.org/29574 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2018-11-10mb/lenovo/t400: Improve docking codePatrick Rudolph
* Remove dead code * Add support for types 2504 and 2505 * Print dock info at romstage entry * Improve dock disconnect for type 2505 * Move defines into dock.h for future ACPI code * Reduce timeouts according to spec to decrease boot time on error * Fix no docking detection (reduces boot time by 1 second) * Configure GPIO LDN before reading GPIOs * Use Kconfig values instead of fixed defines * Add documentation Tested on Lenovo T500 with docking 2504 and 2505. Change-Id: Ic4510ffadc67da95961cecd51a6d8ed856b3ac99 Signed-off-by: Patrick Rudolph <siro@das-labor.org> Reviewed-on: https://review.coreboot.org/29418 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2018-11-09mb/google/kahlee/variants/liara: Decrease eDP adjust time to 20 msChris Wang
Add 20ms adjust timing for edp panel in devicetree. BUG=b:118011567 TEST=verify panel sequences by ODM. Change-Id: Iab46f6fc653047a1ec6e8528eefa0999d7019690 Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29473 Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-09mb/google/kahlee: Tune eDP panel initialization timeChris Wang
1. Add two parameters for panel initialization timing. > lvds_poseq_varybl_to_blon > lvds_poseq_blon_to_varybl 2. The BL_PWM is controlled by APU_EDP_BKLTEN_L/APU_DP_VARY_BL/ EDP_BKLTEN_L, so move APU_EDP_BKLTEN_L to early init stage, and be enabled depends on SKU, thus we can control the delay time by config APU_DP_VARY_BL. BUG=b:118011567 TEST=emerge-grunt coreboot. Change-Id: Ib20c48813b208d697b950b2f02a70a690e483fdb Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29469 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2018-11-09mb/intel/icelake_rvp: Move CNVi ASL entry from static DSDT to dynamic SSDT ↵Subrata Banik
generation This changes uses drivers/intel/wifi chip for CNVi device to ensure that: 1. Correct device name shows in ACPI name space 2. Correct wake up shows in cat /proc/acpi/wakeup 3. Remove cnvi.asl from soc/intel/icelake Change-Id: I21d3818ac9e384b0dbaa330d231022bdb8b8a547 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/29507 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shelley Chen <shchen@google.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
2018-11-08mb/google/sarien: Set runtime IRQs to reset on PLTRSTDuncan Laurie
GPIOs that use GPI_APIC setting with DEEP can cause an IRQ storm after S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic reset over PLTRST to prevent IRQ strom after S3 resume. For sarien/arcada these are all runtime IRQs only, not wake capable. Change-Id: Iec3706a3b47b54abbacd06081910f389979c330f Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/29539 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-11-08mb/google/sarien: Disable eSPI when ACPI is enabledDuncan Laurie
Select the option to disable eSPI when ACPI is enabled so the EC is unable to assert an SMI when booted into the OS. There is a kernel driver that implements the same mailbox interface so it cannot also be used by the SMI handler. Change-Id: I8bafc749f22aed5595e19e773762ee8b038950b9 Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/29536 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-11-08mb/google/poppy/variant/nocturne: configure SAR irqs to use PLTRSTNick Vaccaro
GPIO's that use GPI_APIC setting with DEEP causes an IRQ storm after S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic reset over PLTRST to prevent IRQ storm after S3 resume and hence configuring GPP_D9 and GPP_D10 to use PLTRST. BUG=b:119202293 TEST=none Change-Id: I98d71100f28fb9bae05db3fb7d9afcb3f81beb43 Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/29538 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-08mb/google/poppy/variant/nocturne: use PLTRST for GPP_C11Nick Vaccaro
GPP_C11 (FPMCU_INT_L) was set to DEEP, causing problems with S3. Changed GPP_C11 configuration to use PLTRST instead. BUG=b:114196791 TEST=Build, flash, boot nocturne, log in to kernel and execute the following two commands and verify it passes : echo 0 > /var/lib/power_manager/suspend_to_idle && restart powerd sudo suspend_stress_test -c 2 Change-Id: I008532fce963c51a435378001440ac72b5ebfffc Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/29429 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-11-08mb/google/octopus/variants/baseboard: Improve cold boot and S3 resumeJohn Zhao
FSP 2.0.7.1 provides UPD interface to execute IPC command. Configure PmicPmcIpcCtrl for PMC to program PMIC PCH_PWROK delay from default 100ms to 10ms to improve cold boot and S3 resume performance. BUG=b:118676361 CQ-DEPEND=CL:*703187 TEST=Verified system_resume_firmware_ec time reduction. Change-Id: I41b8268c752573d828e31a1d94d3f175aa3cc145 Signed-off-by: John Zhao <john.zhao@intel.com> Reviewed-on: https://review.coreboot.org/29485 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-08mb/google/poppy/variants/nami: add the hynix memory partsRen Kuo
add the memory parts as ram id 10: hynix_dimm_H5ANAG6NAFR-UHC BUG=b:113983573 BRANCH=Nami TEST=emerge-nami coreboot chromeos-bootimage Change-Id: I137259b88f39779768a58959a2dcc565645eee6d Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29524 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-11-08src/mb/pcengines/apu2/romstage.c: Allow coreboot console output on COM2Michał Żygowski
This change allows to redirect coreboot console output to COM2 by setting appropriate UART index in Console menu in Kconfig. Change is helpful for users which would like to use COM1 port for other purposes, because COM1 is the only port with hardware flow control. Change-Id: I39f88d7e7794f603775a985afe07fef349172e5f Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com> Reviewed-on: https://review.coreboot.org/29255 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2018-11-07siemens/mc_apl4: Add new mainboard variant mc_apl4Mario Scheithauer
This mainboard is based on mc_apl1. In a first step, it concerns a copy of mc_apl1 directory with minimum changes. Special adaptations for mc_apl4 mainboard will follow in separate commits. Change-Id: I3dfdccc8198f3a23a45d319ede6080803a46f7f6 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/29467 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-11-07siemens/mc_apl2: Adjust GPIO settings for mc_apl2Mario Scheithauer
This mainboard variant requires GPIO adaptations to match the hardware. Change-Id: I16387358d6c6fa15efd16f7ba7f6b89740477e9d Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/29318 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2018-11-07mb/{lenovo/x201,packardbell/ms2290}/romstage: Fix commentsPeter Lemenkov
RCBA address numbers in comments looks wrong and confusing. Let's fix them. This is a cosmetic change since no actual data is added or removed. Change-Id: I0e521acdac17959586bc0af7d8a2f7182f1e6721 Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/29511 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-11-07mb/lenovo/*/*: Fix non-local header treated as localPeter Lemenkov
See also commit 4ad1446b with Change-Id I036208a111d009620d8354fa9c97688eb4e872ad ("Fix non-local header treated as local"). Change-Id: Idea19b52198e6f46b0da6022558a46246a52f2e7 Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/29501 Reviewed-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-07mb/lenovo/x201: Remove unnecessary include - delay.hPeter Lemenkov
Change-Id: Ia997c5188aef0c18d871658209c2d5f718ee2a19 Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/29499 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2018-11-07mb/lenovo/x201/gpio: Use reset structurePeter Lemenkov
This structure was defined but never used. Let's use it. Change-Id: I73baf428a7300e64fa486699e82ef62c6a53ea60 Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/29498 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2018-11-07siemens/mc_apl3: Disable I2C7 over devicetreeMario Scheithauer
Disable I2C7 because there is no device connected. Change-Id: Ie9877d40b06f4a849163a873fd308ff03995fcdc Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/29506 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2018-11-07siemens/mc_apl3: Enable all PCIe root portsMario Scheithauer
Enable all PCIe root ports for this mainboard. Change-Id: I62c7ba5048b4c2288bb502a78b9621edda333f2a Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/29505 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-11-07siemens/mc_apl3: Remove reduced clock rate for I2C0Mario Scheithauer
There is no device on I2C0 which requires a lower clock rate. Change-Id: Ib9ad4d9026267d2079e95245994d84c163b28dbb Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/29504 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-11-07siemens/mc_apl3: Disable CLKREQ of PCIe root portsMario Scheithauer
All PCIe root ports of this mainboard do not have an associated CLKREQ signal. Therefore the ports are marked with "CLKREQ_DISABLED". Change-Id: I59c1132c6d273ccefeb1be6243577e1ae5064ef4 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/29502 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-11-07siemens/mc_apl3: Adjust GPIO settings for mc_apl3Mario Scheithauer
This mainboard variant requires GPIO adaptations to match the hardware. Change-Id: I4ba475e7d387f46ed5f41b7a691c7933edbc50c5 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/29496 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-11-07mb/google/sarien: Add sku_id functionDuncan Laurie
This change adds a sku_id() function that returns a static value to differentiate the sarien and arcada boards. Change-Id: I1fecc675573a6aece7188aae9370733068d45dbf Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/29486 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-07mb/google/fizz: Comment variant names in KconfigDavid Wu
Refer to CL:1043916 BUG=none BRANCH=none TEST=none Change-Id: I3fbbbcac334646f68b8b9fd38fbb529d9e833581 Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29464 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-11-07mb/{intel/google}: Move CNVi ASL entry from static DSDT to dynamic SSDT ↵Subrata Banik
generation This changes uses drivers/intel/wifi chip for CNVi device to ensure that: 1. Correct device name shows in ACPI name space 2. Correct wake up shows in cat /proc/acpi/wakeup 3. Remove cnvi.asl from soc/intel/cannonlake Change-Id: Ic81de2dce6045ced913766790a40ed19119f5118 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/29399 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-11-05mb/google/poppy/variants/nami: Enable FP MCUShelley Chen
Some variants of nami will have a fingerprint MCU. BUG=b:118503113 BRANCH=Nami TEST=None (build and boot, but no hw yet) Change-Id: I446dc09cdf7f84a801723cb403d2de80e0997c65 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/29297 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-11-05mb/asus/p5qc: Fix spelling of MarvellJonathan Neuschäfer
Marvell is the chip company, Marvel makes comic books. Change-Id: I437ac0d4fc706fbb62a0a74ca74a197dba4499fb Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-on: https://review.coreboot.org/29347 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2018-11-05mb/google/sarien: Enable WWAN detectionLijian Zhao
WWAN start-up control requires RESET# assert after FULL_CARD_POWER_OFF# set to high more than 10 ms, so force RESET#(GPP_D21) to low at bootblock stage to match the sequence. BUG=N/A TEST=Boot up Sarien/Arcada board, check WWAN get detected as USB devices through lsusb. Change-Id: I36eb841a2e8f2b36771d20577314a7451fbee133 Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/29430 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2018-11-05mb/google/fizz: Remove variant_cros_gpios from variantDavid Wu
This change removes the function defintions from variant so that the weak definition in baseboard can be used. Refer to CL:813944. BUG=none BRANCH=master TEST=Build and boot on DUT Change-Id: I561414fcc94e3c812bb88730df9b94e332c61781 Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29368 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-11-05mb/google/fizz/variants/karma: Update GPIO GPP_D9David Wu
Update GPP_D9 to fix audio jack can't detect issue. BUG=b:118393646 BRANCH=master TEST=Verify audio jack can auto detect. Change-Id: I87d24ed294c1ddc59bbd6ba9194c76d1f66413f3 Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29268 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Zhuohao Lee <zhuohao@chromium.org> Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-11-05mb/google/octopus/var/bobba: Define GPIO_134 as EC_SYNC_IRQEnrico Granata
Use GPIO_134 as the EC sync interrupt and provide this value to the embedded controller to be exported to the OS. BRANCH=none BUG=crbug:896347, b:118443377 CQ-DEPEND=CL:1298699 TEST=verify sensor events coming in on a reworked board with companion EC and kernel patches Change-Id: I41333cabe97bc8b0d59e19d84366f2ea2a59e026 Signed-off-by: Enrico Granata <egranata@chromium.org> Reviewed-on: https://review.coreboot.org/29278 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-05mb/google/poppy/variant/nocturne: add Nanya memory optionNick Vaccaro
Add option for Nanya NT6CL256T32CM-H1 part. Add comments to indicate total memory size for convenience. BUG=b:118624505 BRANCH=master TEST=none Change-Id: I82200e7b3d0a13295cb38f53ab576697ff8d302b Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/29341 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-11-05src: Remove unneeded include <arch/ioapic.h>Elyes HAOUAS
Change-Id: Ic08b191ee4dbcc56eb482601aa268394545936ba Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29292 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-05mainboard: Remove unneeded include <console/console.h>Elyes HAOUAS
Change-Id: Ib3aafcc586b1631a75f214cfd19706108ad8ca93 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29285 Reviewed-by: Patrick Rudolph <siro@das-labor.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-05amd: Fix non-local header treated as localElyes HAOUAS
Change-Id: I0668b73cd3a5bf5220af55c29785220b77eb5259 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29103 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-05src/mainboard: Remove irrelevant conditional statementElyes HAOUAS
Using a conditional statement to return 0 or 1 depending on a logic value is unnecessarily complex. Change-Id: I449ce2b71b72374de5ec4986f9cc9f91a67856ee Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29265 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-04src/mb/asus/p5qc: Fix some mistakesAngel Pons
There are some small mistakes in these recently-added mainboards: - board_info.txt: Lists board socket incorrectly. - cmos.default: Loglevel was decreased some time ago. - devicetree.cb: Spelling mistake. - Kconfig: Mainboard name does not have a hyphen. Change-Id: I08d9b06e79683acd3994b84647bce401ed6741e2 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/29446 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-11-02google/kukui: Add board id supportTristan Shieh
Get board id from AUXIN4 and RAM code from AUXIN3. BUG=b:80501386 BRANCH=none TEST=AUXIN4 is 0.074v and AUXIN3 is 0.212v on P0. AUXIN4 is 0.212v and AUXIN3 is 0.212v on P1. Change-Id: I50533e851d2fae66ae8c5e4e1aa36708d9058e94 Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com> Reviewed-on: https://review.coreboot.org/29062 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2018-11-02mb/google/sarien: Enable Wilco ECDuncan Laurie
The Sarien mainboard uses the newly added Wilco EC. - enable CONFIG_EC_GOOGLE_WILCO - add the device and host command ranges to the devicetree - have the mainboard SMI handlers call the EC handlers - add EC and SuperIO devices to the ACPI DSDT - call the early init hook for serial setup Change-Id: Idfc4a4af52a613de910ec313d657167918aa2619 Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/29411 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-11-02mb/google/sarien: Add Arcada variantDuncan Laurie
Add a variant of the Sarien board called Arcada. This is currently very similar to Sarien with differences in PCIe, USB, and GPIO usage. Change-Id: I432d2ba99558e960d4e775c809cc8bf6aa1a56bf Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/29410 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-02mb/google/sarien: Add new mainboardDuncan Laurie
Sarien is a new board using Intel Whiskey Lake SOC. It also uses the newly added Wilco EC, enabled in a separate commit. Sarien is not a true reference board, it is just one variant of a very similar design. For that reason it is not considered the baseboard but rather a standalone variant. Change-Id: I2e38f617694ed2c2ef746ff8083f2bfd58cbc775 Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/29409 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-11-02mb/google/poppy/variants/nami: Enable radium touchscreen supportRen Kuo
Enable the radium touchscreen support BUG=b:117960394 BRANCH=master TEST= 1. emerge-nami coreboot chromeos-bootimage 2. boot up on ekko DUT to check touchscreen device by evtest /dev/input/event3: Raydium Touchscreen Change-Id: I16167d5d3ce6eac9d64832b52bb1945999a63a90 Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29365 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-02mainboard/intel/icelake_rvp: Add ICL flash layout to support IFWI 1.6Aamir Bohra
Modify flash layout to match ICL-IFWI layout for early SoC PO support Flash Reg 0: Descriptor [0x0 - 0xFFF] Flash Reg 1: BIOS [0x400000 - 0xFFFFFF] Flash Reg 2: IFWI (consist of ME primary & secondary partition and PMC FW) [0x81000 - 0x3FFFFF] Flash Reg 8: EC (applicable for Intel RVP with internal EC support) [0x1000 - 0x80FFF] Change-Id: I462a384739b5972d9a59569ffdcadba7cdef6a81 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Signed-off-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-on: https://review.coreboot.org/29316 Reviewed-by: Shelley Chen <shchen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-01sb/intel/common: Create a common implementation of `acpi_fill_madt()`Tristan Corrick
The function `acpi_fill_madt()` is identical among all the Lynx Point boards and sb/intel/bd82x6x, so share a common function between them. Earlier Intel platforms have similar implementations of this function. The common implementation might only need minor alterations to support them. Tested on an ASRock H81M-HDS and Google Peppy (variant of Slippy). No issues arose from this patch. Change-Id: Ife9e3917febf43d8a92cac66b502e2dee8527556 Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/29388 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-11-01sb/intel/lynxpoint: Add a common platform.asl fileTristan Corrick
The platform.asl file is copied from sb/intel/bd82x6x, and also matches the contents deleted from each mainboard's platform.asl. Tested on an ASRock H81M-HDS and a Google Peppy board (variant of Slippy). No issues arose from this patch. Change-Id: I539e401ce9af83070f69147526ca3b1c122f042c Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/29386 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-11-01sb/intel/lynxpoint: Automatically generate the ACPI PCI routing tableTristan Corrick
This patch is based on a8a9f34e9b7b ("sb/intel/i82801{g,j}x: Automatically generate ACPI PIRQ tables") Tested on an ASRock H81M-HDS. The generated _PRT object looks correct, and the system doesn't show any issue when running. The following assignments occur: ACPI_PIRQ_GEN: PCI: 00:02.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:03.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:14.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:16.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:1a.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:1b.0: pin=0 pirq=6 ACPI_PIRQ_GEN: PCI: 00:1c.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:1c.1: pin=1 pirq=1 ACPI_PIRQ_GEN: PCI: 00:1c.2: pin=2 pirq=2 ACPI_PIRQ_GEN: PCI: 00:1c.3: pin=3 pirq=3 ACPI_PIRQ_GEN: PCI: 00:1d.0: pin=0 pirq=7 ACPI_PIRQ_GEN: PCI: 00:1f.2: pin=1 pirq=3 ACPI_PIRQ_GEN: PCI: 00:1f.3: pin=2 pirq=2 Also tested on a Google Peppy board. The following assignments occur: ACPI_PIRQ_GEN: PCI: 00:02.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:03.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:14.0: pin=0 pirq=2 ACPI_PIRQ_GEN: PCI: 00:1b.0: pin=0 pirq=6 ACPI_PIRQ_GEN: PCI: 00:1c.0: pin=0 pirq=0 ACPI_PIRQ_GEN: PCI: 00:1d.0: pin=0 pirq=3 ACPI_PIRQ_GEN: PCI: 00:1f.2: pin=0 pirq=6 ACPI_PIRQ_GEN: PCI: 00:1f.3: pin=1 pirq=2 ACPI_PIRQ_GEN: PCI: 00:1f.6: pin=2 pirq=1 A diff of the _PRT object for the Google Peppy board is below. The code used in the diff has been modified for clarity, but the semantics remain the same. To summarise the diff: * The disabled PCIe root ports are no longer included. * The LPC controller is no longer included, as it has no interrupt pin. The pins for the remaining LPC devices are each one less. Perhaps the original _PRT object was incorrect? * The SDIO device is no longer included, as it is disabled. * The Serial IO devices are no longer included, but that is due to a separate issue I am having with this system (the devices don't show up under Linux regardless of this patch). In short: their omission is not a fault of this patch. --- pre/_PRT +++ post/_PRT @@ -1,301 +1,157 @@ Method (_PRT, 0, NotSerialized) // _PRT: PCI Routing Table { If (PICM) { - Return (Package (0x12) + Return (Package (0x09) { Package (0x04) { 0x0002FFFF, Zero, Zero, 0x10 }, Package (0x04) { 0x0003FFFF, Zero, Zero, 0x10 }, Package (0x04) { 0x0014FFFF, Zero, Zero, 0x12 }, Package (0x04) { 0x001BFFFF, Zero, Zero, 0x16 }, Package (0x04) { 0x001CFFFF, Zero, Zero, 0x10 }, - Package (0x04) - { - 0x001CFFFF, - One, - Zero, - 0x11 - }, - - Package (0x04) - { - 0x001CFFFF, - 0x02, - Zero, - 0x12 - }, - - Package (0x04) - { - 0x001CFFFF, - 0x03, - Zero, - 0x13 - }, - Package (0x04) { 0x001DFFFF, Zero, Zero, 0x13 }, Package (0x04) { 0x001FFFFF, Zero, Zero, 0x16 }, Package (0x04) { 0x001FFFFF, One, Zero, 0x12 }, Package (0x04) { 0x001FFFFF, 0x02, Zero, 0x11 - }, - - Package (0x04) - { - 0x001FFFFF, - 0x03, - Zero, - 0x10 - }, - - Package (0x04) - { - 0x0015FFFF, - Zero, - Zero, - 0x14 - }, - - Package (0x04) - { - 0x0015FFFF, - One, - Zero, - 0x15 - }, - - Package (0x04) - { - 0x0015FFFF, - 0x02, - Zero, - 0x15 - }, - - Package (0x04) - { - 0x0015FFFF, - 0x03, - Zero, - 0x15 - }, - - Package (0x04) - { - 0x0017FFFF, - Zero, - Zero, - 0x17 } }) } Else { - Return (Package (0x12) + Return (Package (0x09) { Package (0x04) { 0x0002FFFF, Zero, ^LPCB.LNKA, Zero }, Package (0x04) { 0x0003FFFF, Zero, ^LPCB.LNKA, Zero }, Package (0x04) { 0x0014FFFF, Zero, ^LPCB.LNKC, Zero }, Package (0x04) { 0x001BFFFF, Zero, ^LPCB.LNKG, Zero }, Package (0x04) { 0x001CFFFF, Zero, ^LPCB.LNKA, Zero }, - Package (0x04) - { - 0x001CFFFF, - One, - ^LPCB.LNKB, - Zero - }, - - Package (0x04) - { - 0x001CFFFF, - 0x02, - ^LPCB.LNKC, - Zero - }, - - Package (0x04) - { - 0x001CFFFF, - 0x03, - ^LPCB.LNKD, - Zero - }, - Package (0x04) { 0x001DFFFF, Zero, ^LPCB.LNKD, Zero }, Package (0x04) { 0x001FFFFF, Zero, ^LPCB.LNKG, Zero }, Package (0x04) { 0x001FFFFF, One, ^LPCB.LNKC, Zero }, Package (0x04) { 0x001FFFFF, 0x02, ^LPCB.LNKB, Zero - }, - - Package (0x04) - { - 0x001FFFFF, - 0x03, - ^LPCB.LNKA, - Zero - }, - - Package (0x04) - { - 0x0015FFFF, - Zero, - ^LPCB.LNKE, - Zero - }, - - Package (0x04) - { - 0x0015FFFF, - One, - ^LPCB.LNKF, - Zero - }, - - Package (0x04) - { - 0x0015FFFF, - 0x02, - ^LPCB.LNKF, - Zero - }, - - Package (0x04) - { - 0x0015FFFF, - 0x03, - ^LPCB.LNKF, - Zero - }, - - Package (0x04) - { - 0x0017FFFF, - Zero, - ^LPCB.LNKH, - Zero } }) } } Change-Id: Id3f067cbf7c7d649fbbf774648d8ff928cb752a4 Signed-off-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-on: https://review.coreboot.org/29381 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-11-01mb/google/fizz/variants/karma: Rename kalista to karmaDavid Wu
Change the variant name from kalista to karma. According to the CL:1298319, the baseboard name is kalista and the board name is karma. BUG=none BRANCH=master TEST=emerge-kalista coreboot chromeos-bootimage Change-Id: Idea295cc14249721a6dc0fc4e2ef6470d43e16eb Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29314 Reviewed-by: Zhuohao Lee <zhuohao@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-11-01src: Add missing include <stdint.h>Elyes HAOUAS
Change-Id: Idf10a09745756887a517da4c26db7a90a1bf9543 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29403 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-10-31Veyron: add Hynix H9CCNNNBKTMLBR-NTD ddr with RAMID '00Z1'Loop_Wu
Confirm with RK, H9CCNNNBKTMLBR-NTD uses this sdram config. sdram-lpddr3-hynix-4GB.inc BUG=b:117967129 BRANCH=master TEST=None Change-Id: I98afc33fd2cb61343be0dcdc007add75bee9c2af Signed-off-by: Loop_Wu <Loop_Wu@asus.com> Reviewed-on: https://review.coreboot.org/29366 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2018-10-31reset: Finalize move to new APINico Huber
Move soft_reset() to `southbridge/amd/common/` it's only used for amdfam10 now. Drop hard_reset() for good. Change-Id: Ifdc5791160653c5578007f6c1b96015efe2b3e1e Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/29059 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-10-31mb/google/poppy/variants/nami: Perform PL2 setting for syndraJohn Su
According to syndra thermal table, PL2 need to check cpu id. Set up syndra PL2 value. 1. KBL_U PL2 is 25w. 2. KBL_R PL2 is 29w. Refer to b:116836990#comment10. BUG=b:116836990 TEST=The thermal team verify OK Change-Id: I766a886121a089683565608252b4c176c70e88a3 Signed-off-by: John Su <john_su@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29269 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-by: Shelley Chen <shchen@google.com>
2018-10-30mb/google/kahlee: Disable IOMMUMartin Roth
Unfortunately Stoney has an issue where enabling the IOMMU causes a 10%-50% decrease in the integrated graphics performance. It is also disabled by default on other stoney platforms. BUG=b:118612241 TEST=Verify that IOMMU is disabled. Change-Id: Ia396c7227cb21461ec8afbdf746721d4fb28083d Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/29342 Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Daniel Kurtz <djkurtz@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-30siemens/mc_apl3: Add new mainboard variant mc_apl3Mario Scheithauer
This mainboard is based on mc_apl1. In a first step, it concerns a copy of mc_apl1 directory with minimum changes. Special adaptations for mc_apl3 mainboard will follow in separate commits. Change-Id: I963ec63bccf71296c3fdabfcf9f3009c2febc791 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/29353 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2018-10-30src: Add missing include <stdint.h>Elyes HAOUAS
Change-Id: I6a9d71e69ed9230b92f0f330875515a5df29fc06 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29312 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-29mb/google/poppy/variants/nami: Add field to identify single channel DDRShelley Chen
Variants of Nami need to accommodate single channel DDR. Will use GPP_D10 on nami for identification. GPP_D10 will return 1 when device is using single channel DDR and 0 when using dual channel DDR. BUG=b:117194353 BRANCH=None TEST=dmidecode | grep Channel and make sure that the correct number of channels gets returned. Change-Id: If86ab2c5404c4e818ce496ea935227ab5e51730a Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/29233 Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-29mb/lenovo/t430: Set USB always on when calling SMI sleepPeter Lemenkov
Looks like we must do it in the same way as in l520, t420, t420s, t430s, t520, t530, x201, x220, x230 models. No idea why t430 should be handled differently. Change-Id: Ic4851022267caca267b667b4e3c327838e0a0b66 Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/29031 Reviewed-by: Patrick Rudolph <siro@das-labor.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-29mb/lenovo/t400: Use acpi_s3_resume_allowed()Paul Menzel
Apply commit 12d681b2 (intel/i945 gm45: Use acpi_s3_resume_allowed()) also to the Lenovo T400. See also commit 42ae0bae with Change-Id I4e1e0ccf2abbe175c0e5ddcbb6ee7bf6afb1ae88 (mb/lenovo/x200: Use acpi_s3_resume_allowed()) Change-Id: I9d4ac711375977a979a8b3e5606e2197847e88de Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/29147 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2018-10-29Documentation/mainboard: Add emulation/spike-riscv.mdJonathan Neuschäfer
Move the usage instructions from their ad-hoc place in Kconfig.name to the Documentation directory, and expand them a bit. Change-Id: Id6c7bbca40a21ecba00cab736af2f2662a985106 Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-on: https://review.coreboot.org/28874 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Philipp Hug <philipp@hug.cx>
2018-10-27mb/lenovo/x200: Link gpio map instead of including a headerArthur Heymans
Linking should allow to link depending on possible future variants. E.g. in Makefile.inc romstage-$(CONFIG_'VARIANT0') += gpio_variant0.c etc. This commit follows up on commit 7dee9745 with Change-Id I88b5ef8e12ac606751952a493f626e1b146e98f7 ("mb/lenovo/x201: Link gpio map instead of including a header"). Change-Id: Ibdb96deafbe422bf50fd2e1fc56a57ae53ccd5a0 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/29286 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2018-10-27mb/lenovo/*/acpi_tables: Remove comment about IGD displaysPeter Lemenkov
IGD display handling was rewritten with commit dd2bc3f8 with Change-Id I556769e5e28b83e7465e3db689e26c8c0ab44757 ("igd.asl rewrite"). These comments were removed as well (with some accidentally left behind). Let's remove them and those who were introduced later with new ports. Change-Id: I8d3e12d0c3b03b0de38e65f36b94ed706fbf893c Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/29271 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-27mb/lenovo/*/gpio: Remove ifdef guardsPeter Lemenkov
These ifdefs are the remains from the following commits: * fa1d688a with Change-Id I9909a5b2bdb4b59219db6304fa4332802fe0301c ("sandy/ivy native: dedup romstage.c main()") * 7dee9745 with Change-Id I88b5ef8e12ac606751952a493f626e1b146e98f7 ("mb/lenovo/x201: Link gpio map instead of including a header") Change-Id: If83189688151f531a05780a87db3409cbacfbeff Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/29283 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2018-10-26mainboard/intel/icelake_rvp: Do initial mainboard commitAamir Bohra
Clone entirely from mainboard/intel/cannonlake_rvp commit id: af89f49b83260a04dece84b34e97560fb85d29ae List of changes on top off initial cannonlake_rvp clone 1. Rename "Cannonlake" with "Icelake". 2. Replace "cannonlake_rvp" with "icelake_rvp". 3. Rename "cnl" with "icl". 4. Remove unwanted SPD file, will add correct SPD with mainboard patches. 5. Remove NHLT related implementation. 6. Remove FSP configs, will add once FSP headers are available. 7. Removed smihandler.c, will add later if needed. Change-Id: I875972d1fb2f630bf5eb29bd955c484e7f9aa415 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Signed-off-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-on: https://review.coreboot.org/29164 Reviewed-by: Naresh Solanki <naresh.solanki@intel.com> Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-25mb/google/kahlee/irq_tables.c: Prefer using '"%s...", __func__'Richard Spiegel
In function write_pirq_routing_table(), the function name is used in a print string. Use __func__ instead. BUG=b:117642170 TEST=Build grunt. Change-Id: Ibf8673c5b2cda1105aae1edb46f6589d55208c50 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/29245 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2018-10-25mb/google/fizz/variants/kalista: Add variant for kalistaDavid Wu
Add a new variant of fizz for the kalista board. Key differences from baseboard include: - GPIO changes - devicetree.cb changes BUG=b:117066935 BRANCH=master TEST=Build (as initial setup) Change-Id: I808c5e0883049575cbedd181c249a78a833fa96a Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29205 Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-25mb/google/fizz: Enable use of override devicetreeFurquan Shaikh
This change enables override device tree for Fizz to allow variants to provide their own overrides and also moves I2C5 realtek node to fizz/overridetree.cb since it doesn't apply to some variants being added for Fizz. Change-Id: Ia1a069fc539b51a22882ef94b55baf5bf7cd302f Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/29242 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
2018-10-25google/kukui: Support recovery modeTristan Shieh
Get recovery mode switch from EC and pass it to payload. BUG=b:80501386 BRANCH=none Test: Boots correctly on Kukui. Change-Id: Ib92afca885e5a97ec4646f55f2279ef56a61af5a Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com> Reviewed-on: https://review.coreboot.org/29190 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2018-10-24mb/google/kahlee: Enable 2T mode for liarachris wang
Liara auto restart issue is caused by memory access error and consequent kernel panic. To solve this issue, revert the CL:1243666 (Disable NbP-state on Liara) and use 2T mode instead. BUG=b:116082728 TEST=verify the 2T mode is enabled/boot into ChromeOS and no auto restart/run memtester passed 10 cycle. Change-Id: I3a96276d88ffb70530d72b15c07b59a01cc6209a Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29179 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
2018-10-24mb/google/octopus/variants/fleex: Update DPTF parametersJohn Su
1. Update PSV values for cpu and sensers. 2. Change PL1 min value from 3w to 4.5w. 3. Change TSR2 TRT source from charger to CPU. Refer to 112448519#comment31. BUG=b:112448519 TEST=Build coreboot for Octopus board Change-Id: I7c7df0f54374fdaa4cf57d5c255d841d7db38cfc Signed-off-by: John Su <john_su@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29146 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
2018-10-24mb/google/poppy/var/nocturne: Use CRFP as device name for FP deviceFurquan Shaikh
This change uses CRFP ACPI name for FP device since user space utilities expect this name for triggering different actions. BUG=b:112974410 BRANCH=nocturne Change-Id: I63309227c916b43917e529c223cf738fc3baa209 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/29231 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-24mainboard/google/poppy/variants/rammus: Enable touchscreenkane_chen
On rammus, set GPIO GPP_C22 to 1 for touchscreen power on. And add touchscreen device "PNP0C50" to I2C0. According to touchscreen spec, device power on initialization takes 105 ms, so set "generic.enable_delay_ms" to 120. We found there is i2c error log pop up when we set delay time to be 110ms or 105ms. If we set delay time to be 120ms. System will not pop up i2c error log. BUG=b:115944726 BRANCH=master TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage Flash FW to DUT, and make sure touchscreen works. Change-Id: Ibce552d04991e85c99ae3a0a92455fc747d9fced Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/28598 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Zhuohao Lee <zhuohao@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-10-24mb/google/octopus: Use DIMM_INFO_PART_NUMBER_SIZE for part_num_storeFurquan Shaikh
This change uses DIMM_INFO_PART_NUMBER_SIZE to decide the size of part_num_store that holds the number of DRAM part. It ensures that host advertises the supported size to read part number from the EC. BUG=b:115697578 Change-Id: I8439a301fc037b0acdc8b1226ad04d2f363838ef Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/29241 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Jett Rink <jettrink@chromium.org>
2018-10-23mb/google/poppy: add the smi_events backZhuohao Lee
Before entering the OS, the AP relies on the smi handler to shutdown the system when the lid closes. Without the smi_events setting, the AP will not receive the smi handler. As a result, the AP won't shutdown and will always keep in S0. This problem is caused by the https://review.coreboot.org/c/coreboot/+/28983 and this patch adds the smi_events back to support the smi handler for the lid close. BRANCH=master BUG=b:115572596 TEST=test_that -b ${BOARD} ${IP} firmware_ECLidShutdown Change-Id: Id82311a8ccd109f9c26516f59a45bdf34da98529 Signed-off-by: Zhuohao Lee <zhuohao@chromium.org> Reviewed-on: https://review.coreboot.org/29191 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2018-10-23src: Remove unneeded whitespaceElyes HAOUAS
Change-Id: I6c77f4289b46646872731ef9c20dc115f0cf876d Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/29161 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2018-10-23mb/kahlee mb/gardenia: Remove smbus.asl includeRichard Spiegel
The file soc/amd/stoneyridge/acpi/smbus.asl has 0 bytes (no content). Remove the include of this file. BUG=b:117814641 TEST=Build grunt and gardenia. Change-Id: I0c48167195a9708afc255490bb1996b6dfc7bdfb Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/29178 Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-23mb/google/octopus: Use a single GPIO for trackpad wake and IRQFurquan Shaikh
This change uses the newly added macros for configuring the same GPI pad(GPIO_135) for IRQ (normal interrupt operations) and wake (interrupt for waking from S3/S0ix) for the trackpad device. The other pad GPIO_142 is now configured as not connected. BUG=b:117553222 TEST=Verified that yorp and bobba wake from S3 and S0ix using trackpad. Change-Id: I2b704f1be493141629c647b79723b0025b0f7dd6 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/29189 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-22mb/google/poppy/var/nocturne: Change IMX319 sensor link freqLijian Zhao
Change link frequency of IMX319 from 360Mhz to 482.4 Mhz to match the changes from kernel driver. IMX319 has two PLLs and it can be configured either single or dual. Previous driver implemente dual PLL mode, however image sensor vendor prefer single PLL mode and calculate the pixel rate became easier. So the kernel driver changed to use single pll, coreboot change will match that. Bug=b:116082248 Change-Id: Iac9a72253e0529bf2c0785fb701b7bc251bcbab5 Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/28736 Reviewed-by: Tomasz Figa <tfiga@google.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-22mb/lenovo/*/romstage: No need to specify board's model in commentsPeter Lemenkov
This is a cosmetic one. It just removes some board names from comments since these functions sometimes are very similar, so no need to add extra difference between them. Change-Id: I26b9296b402d98bcf048580da51da7bbb0c237e4 Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/29180 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2018-10-22mainboard/: Select MISSING_BOARD_RESET appropriatelyNico Huber
We didn't have a hard_reset() implementation for these boards. So select the board_reset() stub for them. Change-Id: I77651e3844632fb1a347008c96e53d23cc5a2646 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/29170 Reviewed-by: Julius Werner <jwerner@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-22amdfam10: Convert to `board_reset()`Nico Huber
And here comes the mess... This just renames do_hard_reset() to do_board_reset() and keeps current behaviour. As these are never called from chipset or board code but only from common code, it's likely that their implementations are untested and not what we actually want. Also note, that sometimes implementations for rom- and ramstage differ considerably. Change-Id: Icdf55ed1a0e0294933f61749a37da2ced01da61c Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/29058 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-22intel: Use CF9 reset (part 1)Patrick Rudolph
Add SOUTHBRIDGE_INTEL_COMMON_RESET for all Intel platforms that used to perform a "system reset" in their hard_reset() implementation. Replace all duplicate CF9 reset implementations for these platforms. Change-Id: I8e359b0c4d5a1060edd0940d24c2f78dfed8a590 Signed-off-by: Patrick Rudolph <siro@das-labor.org> Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/28862 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-10-22soc/rockchip/rk3399: Convert to `board_reset()`Nico Huber
Change-Id: Id07e1c7fbd35393ffafda53fc7a15ec0e157d075 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/29049 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2018-10-22reset: Convert individual boards to `board_reset()`Nico Huber
Change-Id: I6182da172ae2f4107a9b5d8190e4b3b10ed2f0b9 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/29048 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2018-10-19mb/google/octopus: Preserve MRC training data across firmware updateFurquan Shaikh
This change udpates FMAP to wrap MRC training data in RW_PRESERVE section so that we don't lose the data when performing full firmware updates on octopus. BUG=b:117882029 TEST=Verified that chromeos-firmwareupdate doing full firmware update preserves training data on octopus. Change-Id: I5adb9bfa926327057b003360150685a8b4778c8c Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/29183 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-10-19mb/google/fizz: Provide nhlt variant APIDavid Wu
Move current NHLT configuration implementation to baseboard so that variants can leverage it or provide their own configuration. BUG=b:117066935 BRANCH=Fizz TEST=emerge-fizz coreboot Change-Id: I30d93babb6fc09e8642b3740f1f7638fa33f0ade Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/28965 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-10-19mb/google/fizz: Provide cros_gpio variant APIDavid Wu
Add support for ChromeOS GPIO ACPI table information by providing weak implementation from the baseboard. BUG=b:117066935 BRANCH=Fizz TEST=emerge-fizz coreboot Change-Id: I2fa52c005cacdbcc322d107a3ac92d22df3f3697 Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/28964 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-10-19mb/google/fizz: Add variant API for gpioDavid Wu
Provide API for gpio table functionality. Default weak implementations are provided from the baseboard. BUG=b:117066935 BRANCH=Fizz TEST=emerge-fizz coreboot Change-Id: Iaafa8d6932bc0a37826175b15816f1b9a4f4c314 Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/28963 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-10-19mb/google/fizz: Provide baseboard and variant conceptsDavid Wu
In order to be able to share code across different fizz variants, provide the concept of baseboard and variants. New directory layout: variants/baseboard - code variants/baseboard/include/baseboard - headers variants/fizz - code variants/fizz/include/variant - headers New boards would then add themselves under their board name within "variants" directory. This is purely an organizational change. BUG=b:117066935 BRANCH=Fizz TEST=emerge-fizz coreboot CQ-DEPEND=CL:1273514 Change-Id: I28cc41681e7af88ddeba2e847dc0a4686606feb2 Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/28962 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-10-19google/grunt: Remove unused MRC regions from FMAPRaul E Rangel
I didn't change the offsets of all the other regions because I didn't want to cause all dogfood devices to lose their corp enrollment. BUG=b:117797131, b:117798830 BRANCH=none TEST=Ran autotest and made sure the tests were skipped /tmp/test_that_results_2OZ90v/results-1-firmware_CorruptRecoveryCache [ PASSED ] /tmp/test_that_results_2OZ90v/results-1-firmware_CorruptRecoveryCache TEST_NA: No RECOVERY_MRC_CACHE was found on DUT. /tmp/test_that_results_2OZ90v/results-1-firmware_CorruptRecoveryCache/firmware_CorruptRecoveryCache.normal [ PASSED ] /tmp/test_that_results_2OZ90v/results-1-firmware_CorruptRecoveryCache/firmware_CorruptRecoveryCache.normal TEST_NA: No RECOVERY_MRC_CACHE was found on DUT. Change-Id: I5cdbf4139dde80fe6e9d0045139a97841b03bc42 Signed-off-by: Raul E Rangel <rrangel@chromium.org> Reviewed-on: https://review.coreboot.org/29171 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-10-19mb/intel/coffeelake_rvp: Add HDA controller driver support for coffee lakepraveen hodagatta pranesh
this patch adds following changes - Select config to initialize codecs in common HDA driver. - Add audio verb table for coffee lake RVP11 & RVP8. BUG: None TEST: boot to yocto linux and windows os on CFL RVP11 & RVP8. verified audio playback and record functionality over anolog audio jack & HDMI display. Change-Id: I567e317c0e9ac9f91e159866c7f896e4c101712b Signed-off-by: praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com> Reviewed-on: https://review.coreboot.org/29067 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-10-19mb/lenovo/*/romstage: Remove explicit power-on defaultsPeter Lemenkov
Change-Id: Ib359e4039f87bb87faac040f24f70cc0988c0ea8 Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/29107 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2018-10-18src/mainboard: Remove unneeded whitespaceElyes HAOUAS
Change-Id: Ibf23f49e7864c611a3cb32a91891b6023a692e1d Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/28979 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2018-10-18mb/google/glados/variants/sentry: Remove unnneded whitespaceElyes HAOUAS
Change-Id: Ibc928dc66e00dbb40d25420fd92f6c5f8049dec1 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/28703 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-18minnowmax: allow both 1333 and 1066 MHz memory SKUsMichał Żygowski
The E3827 and E3845 SKUs are fused at 1333MHz DDR3 speeds. Use frequency as a proxy to determine SKU. The E3805, E3815, E3825, and E3826 are all <= 1460MHz while the E3827 and E3845 are 1750MHz and 1910MHz, respectively. This will allow to boot quad-core Minnowboard Turbot especially. Change-Id: I5e57dd419b443dfa742c8812cec87274af557728 Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com> Reviewed-on: https://review.coreboot.org/27989 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 11:42:10 +0000