| Age | Commit message (Collapse) | Author |
|---|
|
The ChromeEC board directories for auron and rambi have been removed
from the latest version of ChromeEC. Remove them here so the submodule
can be brought forward.
Change-Id: I763d03009f735d3f8aedbeb44788d03714c86102
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
Update the world facing camera sensor to OV13858 and also
add delay of 5ms after xshutdown rising which indicates system
ready status.
BUG=b:38326541
BRANCH=none
TEST=Build and boot soraka. Dump and verify that the generated DSDT table
has the required entries. Verified that sensor probe is successfull.
Change-Id: I0cd535e6568f104ffaa1092a13667def646df0eb
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Add clock frequency property into _DSD ACPI object and set it
to 19.2MHz for camera sensors. Upstream camera kernel has added
a check for clock frequency in sensor probe function and without
this property sensor probe fails.
BUG=b:38326541
BRANCH=none
TEST=Build and boot poppy. Dump and verify that the generated DSDT table
has the required entries. Verified that sensor probe is successfull.
Change-Id: I147b3c932a33ae034868f7f9b616500d24ca71e3
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20294
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Correct all checkpatch errors but leave two errors in place
that are caused by AMD typing.
Change-Id: I9daa374da76ff991de72d16bad0e8b586aa95525
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Switch Garnenia mainboard to single soc/ directory structure.
Change-Id: I095804d603bcccf324d3244965081a9dccba62ae
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
It does not work to enable the LPC range in the function
mainboard_init() because the LPC bus driver closes the range during PCI
enumeration again. For this reason, enabling decoding of the address
range for COM 3 will be done at a later point in time -
mainboard_final().
Change-Id: I452bca4e430b1ea75e4a327591da84500491fe84
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With enabled XDCI support we are not able to use USB port 0 over XHCI
driver. For this reason, we disable XDCI into devicetree.cb.
Change-Id: I1ed721d9ffd44a920a6f1f16855d5b7ceb1b17c5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This board can't be found to be tested, and compiles romstage with
romcc. If desired, it can be continued in the 4.6 branch.
Change-Id: I4826c277bbb444c2f0573729d76cd492ade95b4c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
resources
This patch controls the camera devices power through ACPI power resource.
* Add Opregions for PMIC,
* TI_PMIC_POWER_OPREGION
* TI_PMIC_VR_VAL_OPREGION
* TI_PMIC_CLK_OPREGION
* TI_PMIC_CLK_FREQ_OPREGION
* Add power resources for sensors and VCM,
* OVTH for CAM0
* OVFI for CAM1
* VCMP for VCM
* Implement _ON and _OFF methods for sensor and VCM module's power on
and power off sequences.
BUG=b:38326541
BRANCH=none
TEST=Build and boot poppy. Dump and verify that the generated DSDT table
has the required entries.
Change-Id: I87cd0508ed5ed922211a51f43ee96b6f44cf673d
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/20054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Bind the camera sensor and CIO2 devices through the ports and endpoints
configuration available in _DSD ACPI object.
* Port represents an interface in a device.
* Endpoint represents a connection to that interface.
BUG=b:38326541
BRANCH=none
TEST=Build and boot poppy. Dump and verify that the generated DSDT table
has the required entries.
Change-Id: I6d822165bb9a0cd6f7d4cdcb36333887953110a3
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable RT8168_GET_MAC_FROM_VPD in fizz Kconfig.
BUG=b:62090148, b:35775024
BRANCH=None
TEST=Boot to kernel. Insert mac address into VPD
vpd -s ethernet_mac=<address>
reboot the system.
Ensure we have ip address and corresponding mac
address with ifconfig.
Ensure ethernet controller shows up with lspci.
Change-Id: I00f63dcb56a2c9a4600c8461bc94e06ec5ab2d81
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/20232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
By default disabled. Will need to add
FIZZ_USE_SPI_TPM config to enable.
BUG=b:62456589, b:35775024
BRANCH=None
TEST=Reboot and ensure that TPM works in verstage
CQ-DEPEND=CL:530184
Change-Id: I14ce73a1c3745c996b79c4d4758ca744e63a46b4
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/20134
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:62456589, b:35775024
BRANCH=None
TEST=Reboot and ensure verstage doesn't have any TPM errors
CQ-DEPEND=CL:530185
Change-Id: Icfde0f62bd058d960fcb0c6fc67f9d8f6b9462f5
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/20133
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds mipi_camera.asl,
* Add TPS68470 PMIC related ACPI objects.
* Add OV cameras related ACPI objects.
* Add Dongwoon AF DAC related ACPI objects.
* SSDB: Sensor specific database for camera sensor.
* CAMD: ACPI object to specify the camera device type.
BUG=b:38326541
BRANCH=none
TEST=Build and boot poppy. Dump and verify that the generated DSDT table
has the required entries.
Change-Id: If32a2a8313488d2f50aad3feaa79e17b1d06c80f
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/19621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Remove MIPI camera related register entries from devicetree.cb.
BUG=b:38326541
BRANCH=none
TEST=Build and boot poppy and soraka.
Change-Id: Ic6a6a98d4c8ed6cba760eae5fd87bc2a3f15d7d2
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/19619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fixes 2 reports found by undefined behavior sanitizer. Dereferencing
pointers that are not aligned to the size of access is undefiend
behavior.
Change-Id: Iaa3845308171c307f1ddc7937286aacbd00e3a10
Signed-off-by: Ryan Salsamendi <rsalsamendi@hotmail.com>
Reviewed-on: https://review.coreboot.org/20155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Disable TPM when VBOOT_MOCK_SECDATA is enabled.
BUG=None
BRANCH=None
TEST= Build image using USE="mocktpm" emerge-poppy coreboot depthcharge
vboot_reference chromeos-bootimage . Verify boot is successful with mock
tpm.
Change-Id: Iee527ed17cffb7d25d9089e48a194d99ac8c3cd1
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
RAMD_ID_1 moves to PAD_DSI_TE and RAM_ID_2 moves to PAD_RDP1_A on Rowan.
BUG=chrome-os-partner:62672
BRANCH=none
TEST=emerge-rowan coreboot
Change-Id: Iae44934d8d669d696b83f9d3e3450a0e408fe062
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Gerrit-Rebase-Ignore-CLs-Before: https://chromium-review.googlesource.com/539234
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/388068
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/453778
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/454921
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/455118
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/479613
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/487023
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/498587
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/506785
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/520572
Original-Commit-Id: 4da19b3c00578f96ec933cff9ad0c9988a4c4a30
Original-Change-Id: I64fd29de607a0b360d355fd3724e3a649adc658b
Original-Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/448397
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18583
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The differential signal of DQS needs to keep low
level before gate training. RPULL will connect
4Kn from PADP to VSS and a 4Kn from PADN to
VDDQ to ensure it. But if it has PHY side ODT
connected at this time, it will change the DQS
signal level. So it needs to disable PHY side ODT
when doing gate training.
BRANCH=None
BUG=None
TEST=boot from bob
Change-Id: I56ace8375067aa0bb54d558bc28172b431b92ca5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: cb024042c7297a6b17c41cf650990cd342b1376f
Original-Change-Id: I33cf743c3793a2765a21e5121ce7351410b9e19d
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/448278
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://review.coreboot.org/18582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Use verb table values from AMI firmware, consolidate NID
definitions using azalia macros. Fixes headphone jack detection
and microphone.
Change-Id: Ia31be6efc7afe921ad91b400f66694d951f0a260
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Initialize the audio codec without depending on DSP binary blobs.
The hda_verb.c was copied from the intel/kblrvp rvp7 variant, and the
hda_verb.h file was copied from the purism/librem13.
The IoBufferOwnership FSP option in devicetree has to be 0 for the azalia
driver to work.
Change-Id: Ifa36ac0839daedfa59c497057da0ace04d401f2a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Some NVMe devices (Intel 600p series for example) seem to lock up
in D3 drive power state (L1.2 PCIe power state).
Disabling L1 substates fixes it.
Change-Id: I00a327dc91d443beb565fe4e72aaf816e40a007c
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Enable libgfxinit.
Tested on Lenovo T430:
* LVDS
* VGA
* DP (using DP->HDMI adapter)
All three ports are working. The LVDS port is garbled under linux
when VGA or DP is connected, likely due to missing VBT.
Change-Id: I665661e93724072d1e8412cfcc0e818f824c8cb0
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use a GNVS variable to store the trackpad interrupt, in order to
support both SNB and IVB variants from a single build.
Change-Id: I53df35fff41f52a7d142aea9b1b590c65195bcfd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Existing value was copied from librem13 v1 board, use value
obtained from AMI firmware.
TEST: Observe Windows boots correctly, function keys work
under both Windows and Linux.
Change-Id: I0ea6cc4602ce1047cb803acc65cbca1af1f480b0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add default values for MAINBOARD_VERSION and CBFS_SIZE.
Change-Id: Ib6461cef78f3fea448baf1ada456e3c8335f1543
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
|
|
- remove unused I2C, serialIO defs
- set PL2 override, VR mailbox cmd based on SKL-U ref board,
as values copied from google/chell are for SKL-Y
Change-Id: I3a138c28d0322df6cb41ec1a845ae31602cb69a7
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19941
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Update devicetree USB config based on board spec.
Leave OC pins set to skip since the info is unavailable.
Change-Id: I2a4fe17ed7edacbbbaf56969f9d2801b45a20da9
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The board dutifully registers an int15h handler and provides the
defaults to add a VGABIOS.
That should be good enough to initialize graphics through the VGABIOS
file.
Fixes build on Chrome OS configurations (at least until the Ada toolchain
situation is resolved over there).
Change-Id: I1d956b5a163b7cdf2bd467197fba95f16e5e8fa3
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
As the hardware designed on gru, the AP_I2C_TP_PU_EN (gpio3_b4) controlled
the SCL/SDA status to avoid leakage. And the gpio3_b4 of rk3399 pull
resistor is 26k~71k and 3.3v for supply power, and gpio3_b4 pin connected
2.2k resistor to i2c of TP device.
The default of this gpio status is pulled up during the start to bootup,
it's very weak drive for the TP device that maybe cause to trigger the
recovery process of elan's firmware.
Also, the Elan updated its firmware(102.0.5.0) to delay checking the
i2c of touchpad is greater than 1 second.
So we have to drive the stronger pull-up within 1 second of powering up
the touchpad to prevent its firmware from falling into recovery.
Change-Id: I9a67d1c041afafde24ed9f00716ba41a9b41a8da
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Too low gfx_uma_size can result in problems if the framebuffer
does not fit.
This partially reverts: 7afcfe0 "gm45: enable setting all vram sizes
from cmos"
Change-Id: I485d24198cb784db5d2cfce0a8646e861a4a1695
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
TEST=Verified that board still boots to OS without any error.
Change-Id: I02d2a6cbcab92766a35993bfd20aaeed4ca22c90
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Now that we dynamically disable TPM interface based on config options,
add support for generation of SPI TPM ACPI node if SPI TPM is used.
Change-Id: I87d28a42b48ba916c70e45a061c5efd91a8a59bf
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Based on the config options selected, decide at runtime which TPM
interface should be disabled so that ACPI tables are not generated for
that interface.
TEST=Verified that unused interface does not show up in ACPI tables.
Change-Id: Iee8f49e484ed024c549f60c88d874c08873b75cb
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20141
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
There are many good reasons why we may want to run some sort of generic
callback before we're executing a reset. Unfortunateley, that is really
hard right now: code that wants to reset simply calls the hard_reset()
function (or one of its ill-differentiated cousins) which is directly
implemented by a myriad of different mainboards, northbridges, SoCs,
etc. More recent x86 SoCs have tried to solve the problem in their own
little corner of soc/intel/common, but it's really something that would
benefit all of coreboot.
This patch expands the concept onto all boards: hard_reset() and friends
get implemented in a generic location where they can run hooks before
calling the platform-specific implementation that is now called
do_hard_reset(). The existing Intel reset_prepare() gets generalized as
soc_reset_prepare() (and other hooks for arch, mainboard, etc. can now
easily be added later if necessary). We will also use this central point
to ensure all platforms flush their cache before reset, which is
generally useful for all cases where we're trying to persist information
in RAM across reboots (like the new persistent CBMEM console does).
Also remove cpu_reset() completely since it's not used anywhere and
doesn't seem very useful compared to the others.
Change-Id: I41b89ce4a923102f0748922496e1dd9bce8a610f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19789
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Since this mainboard provides 3 COM ports on LPC, enable decoding of the
corresponding address range for COM 3.
Change-Id: I15c0748fce67eef46401c314f441aa45f5e3c5fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
- use Siemens NC FPGA driver for backlight brightness and PWM control
- set Dsave time for board reset after falling edge of signal xdsave
Change-Id: I5077d4af162e54a3993e5e0d784a8356f51bd0c9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I558e6c63caf95ec5279ec5a866b54fb199116469
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Based on the Intel G41 chipset, ICH7 southbridge, and IT8720F Super I/O.
Tested, working:
* Booting Linux 4.11.3 and Windows 8.1 from USB and HDD
* Resume from S3 (Linux and Windows)
* Native raminit (DDR2-800)
* Native graphics init (SeaBIOS, Linux)
* Graphics init with VGA BIOS (SeaBIOS, Windows)
* PCI-E x16 PEG slot, PCI-E x1 slot from southbridge
* Realtek ALC888 HD Audio (including front panel and jack detection)
* Realtek R8168 Gigabit LAN
* Both SATA ports
* USB 1.1 and 2.0 devices (keyboard, mass storage)
* PC speaker beep
* COM header
* Super I/O Environment controller (temps, voltage, fans)
* PS/2 keyboard and mouse
* Flashing with `flashrom -p internal`
* 1MiB and 2MiB SPI flash chips
* CMOS gfx_uma_size
Appears, OS driver loads, but otherwise untested:
* IrDA header
* CIR header
* TPM header
Untested:
* S/PDIF digital audio
Tested, known broken:
* CMOS power_on_after_fail
* USB keyboard in secondary payloads
Change-Id: Ifc4c8935b1a11e55f4bf6cfa484a8a8d09b1adda
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20027
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
I updated my spike patch[1] to cleanly apply to current spike master.
As a side effect, the UART is now at 0x02100000.
[1]: https://github.com/riscv/riscv-isa-sim/pull/53
Change-Id: I4cb09014619e230011486fa57636abe183baa4be
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/20126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
For an unknown reason, the I2C ACPI devices were placed
under \SB intead of \SB.PCI0, as with all other non-Atom
based Intel platforms. While Linux is tolerant of this,
Windows is not. Correct by moving I2C ACPI devices where
they belong.
Also, adjust I2C devices at board level for google/rambi
as to not break compilation.
Change-Id: I4ef978214aa36078dc04ee1c73b3e2b4bb22f692
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20056
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The supported "G41C-GS" with a nuvoton nct6776 superio is actually
G41C-GS R2.0, which is different with the more easily-found revision
G41C-GS (R1.0) with Winbond W83627DHG superio, and should be ported
separately.
Photos for the two revision:
R1.0: https://web.archive.org/web/20160915160553/http://www.asrock.com/mb/photo/G41C-GS(L1).jpg
R2.0: https://web.archive.org/web/20160717203810/http://www.asrock.com/mb/photo/G41C-GS%20R2.0(L2).jpg
Change-Id: If60a694bcf0652ab32c0ac75ceec7e27e11fe9eb
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/19980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Update devicetree PCI config based on board spec:
- enable PCIe Root Ports 5 and 9 (wifi and nvme respectively)
- enable PCIe CLKREQ on RP9, disable on RP5
- enable USB OTG
- enable P2SB
Note: PCIe RP5 is on 0.1c.0 despite this being labeled as RP1
Change-Id: Ia71ed25bd41668df1ee3e4b4e28f54482722452c
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Needed for UEFI booting via Tianocore;
with PM timer disabled, payload hangs.
Change-Id: I6c65cb9d3e6a10baea4cc1e2d9e94c36fe419561
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ib63e5e8a1bcbc25c288dec7d1ef6c06239ada34b
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The FSP Temp RAM init will fail if the mircocode values are set
to 0. A valid microcode update needs to be included and its size
and offset need to be set in the config.
Change-Id: I26d05bd7b37c8d91bf34f399c7c4189f9d3dd34a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19936
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Adding code to setup the spd information from sodimm.
Adapted from intel/kblrvp.
Change-Id: I0403f999dac1bdef0e9e1abe7c9c62407e223bb1
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The GPIO configuration matches the one from the original BIOS.
Some configs don't make much sense, but I kept it as is so it
would match (such as a NC pin with TX set to 1, or RXINV enabled).
Remove unnecessary early GPIO config.
Change-Id: Iaec8630cef9a523fb2e2503143aa4aa72fbedc1f
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19934
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Like other devices using ENE embedded controllers, the librem13v2
requires this config option for the PS2 keyboard and mouse
(trackpad) to function properly.
Change-Id: Ifba13b93a1fe2e76b2790d1c273fd9e2b5368ab0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add the initial directory for the port of the Librem 13 v2.
The base implementation was copied from the google/chell directory
and the chell references were replaced. spd directory was removed
since the RAM is not soldered on the MB. The Kconfig, board_info.txt
and devicetree.cb files were modified to match the Librem 13 v2
hardware information. The romstage.c, mainboard.c, Makefile.in and
dsdt.asl were modified to remove chromeos specific code. The boardid.c,
chromeos.c, chromeos.fmd, cmos.layout, ec.c, ec.h and smihandler.c
files were removed from the tree, and the acpi directory was replaced
with the acpi directory from the purism/librem13 board.
These changes allow us to remove the references to chromeos specific
code and allow coreboot to compile when the librem13v2 board is selected.
Change-Id: I24263fde18fcea70163dbdc59df6ea1d98c97af8
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The FADT revision was set to 5, but we do not implement the
ACPI v5.0 specification, which prevents Windows from booting.
Setting it to v3 (matching most other boards) fixes the issue
and Windows now boots normally.
Bug found by Matt DeVillier, fix tested by Youness Alaoui on
Librem 13 v1 hardware.
Please also see commits 00d250e2289de (intel/skylake: Switch FADT
to ACPI version 3.0) [1] and 27e6042bb7d0b1 (intel/apollolake:
Switch FADT to ACPI version 3.0) [2].
[1] https://review.coreboot.org/19453
[2] https://review.coreboot.org/19146
Change-Id: Ide97cbf64f7b05018433436431ab4723b217fe22
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
A simple rename of the directory and the config values
and string in Kconfig/Kconfig.name/board_info.txt
It will be less confusing for users since the first models
are referred to as 'v1' everywhere now.
Change-Id: I23fa977717230c2001868741bb684e9633a2c0bb
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19931
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
For an unknown reason, the I2C ACPI devices were placed
under \SB intead of \SB.PCI0, as with all other non-Atom
based Intel platforms. While Linux is tolerant of this,
Windows is not. Correct by moving I2C ACPI devices where
they belong.
Also, adjust I2C devices at board level for intel/strago
and google/cyan as to not break compilation.
Change-Id: Iaf8211bd86d6261ee8c4d9c4262338f7fe19ef43
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20055
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Change-Id: Ie0b64eadc634049f6b65cf555407337fb7c4363c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Switch from lapic to tsc.
Allows timestamps to be used in coreboot, as there's a reference
clock available to calculate correct time units.
Clean Kconfig, remove duplicated lapic code and include tsc dir for
LGA1155 boards.
Tested on Lenovo T430.
Change-Id: I849ca2b3908116d9d22907039cd6e4464444b1d1
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update user facing camera i2c address to 0x36.
BUG=None
TEST=Build & boot on soraka. Make sure user facing camera is detected.
Change-Id: I4645ae5734faef4b6a821c04ab817a7b99da6e4b
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
|
|
The new config choice is called RUN_FSP_GOP. Some things had to happen
on the road:
* Drop confusing config GOP_SUPPORT,
* Add HAVE_FSP_GOP to chipsets that support it,
* Make running the GOP an option for FSP2.0 by returning 0
in random VBT getters.
Change-Id: I92f88424004a4c0abf1f39cc02e2a146bddbcedf
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Provide all gfx init methods as a Kconfig `choice`. This elimates the
option to select native gfx init along with running a Video BIOS. It's
been only theoretically useful in one corner case: Hybrid graphics
where only one controller is supported by native gfx init. Though I
suppose in that case it's fair to assume that one would use SeaBIOS to
run the VBIOS.
For the case that we want the payload to initialize graphics or no
pre-boot graphics at all, the new symbol NO_GFX_INIT was added to the
choice. If multiple options are available, the default is chosen as
follows:
* NO_GFX_INIT, if we add a Video BIOS and the payload is SeaBIOS,
* VGA_ROM_RUN, if we add a Video BIOS and the payload is not SeaBIOS,
* NATIVE_VGA_INIT, if we don't add a Video BIOS.
As a side effect, libgfxinit is now an independent choice.
Change-Id: I06bc65ecf3724f299f59888a97219fdbd3d2d08b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
MAINBOARD_FORCE_NATIVE_VGA_INIT is to be selected instead of the user
option MAINBOARD_DO_NATIVE_VGA_INIT. The distinction is necessary to
use the latter in a choice.
Change-Id: I689aa5cadea9e1091180fd38b1dc093c6938d69c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add support for ELAN 5515 device.
BUG=b:62331218
Change-Id: Id91a41743330c9e356293cfda7b2e3743dcd480c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20040
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The word 'coreboot' should always be written in lowercase, even at the
start of a sentence.
Change-Id: I7945ddb988262e7483da4e623cedf972380e65a2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The coreboot sites support HTTPS, and requests over HTTP with SSL are
also redirected. So use the more secure URLs, which also saves a
request most of the times, as nothing needs to be redirected.
Run the command below to replace all occurences.
```
$ git grep -l -E 'http://(www.|review.|)coreboot.org'
| xargs sed -i 's,http://\(.*\)coreboot.org,https://\1coreboot.org,g'
```
Change-Id: If53f8b66f1ac72fb1a38fa392b26eade9963c369
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/20034
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Wrapping the long line tries to address a warning by `checkpatch.pl`,
but the line is still over 80 characters long.
Change-Id: Ib75d4da1880624eb83f7a419cb6762f1c4c2a7b2
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/20033
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The comma-separated PCI vendor and device ID is used to associate the
VGA BIOS to the video device by using it as the file name of the VGA
Option ROM.
Change-Id: I755554eeb9a560d034d6e8fe49de619d800ea045
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/18741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Changes the offsets of some options so that options that span multiple
bytes are byte aligned.
To make the cmos.layout file more consistent some things where moved
around in the cmos.layout of thinkpads X200 and T400.
Change-Id: Ic84a2a5dc6f9c102f041085871c2ed55e2f3692a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
A new variant copied from reef.
Allow override of the SKU.
Change-Id: Ibe160e75aa23623812f0fb9121d1d8226afc00d8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20020
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each rambi variant has a different USB port config.
Port data currently available for only candy and squawks;
other variants to be added once data obtained.
Change-Id: If7ce3d135d6ffe53ab1566d5258d01b052ac47f4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each jecht variant has a different USB port config.
Change-Id: I3b15aac9c4971e2ae230106016fba3a583ec6c9a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19971
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each auron variant has a different USB port config.
Change-Id: Id17f21c23540d2e3d5a902a2174b66c7a5a5f3e0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since dual-channel setups use same RAM/SPD for both channels,
populate spd_data[1] with same SPD data as spd_data[0],
allowing info for both channels to propogate into the
SBMIOS tables.
Clean up calculations using SPD length to avoid repetition.
Changes modeled after google/auron variants.
Change-Id: I7e14b35642a3fbaecaeb7d1d33b5a7c1405bac45
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
No reason to compile/include chromeos.c for non-ChromeOS builds
Change-Id: Ie8ef1f4c521b2a7308941299f2501073937bdf4a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
sata_devslp_disable was set to work around some buggy SSD
firmware, but as it's disabled by default in both Linux and
Windows, no reason to disable at the firmware level when
many properly-functioning SSDs can take advantage of power
savings.
Change-Id: Ib15f8b51db19b3d9d2e135f85c71a15a45a2ffbd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Update camera sensor detail to OV 13858
Also update i2c address of OV5670
BUG=None
TEST= Build & boot to ChromeOS. Check for both the camera detection.
Change-Id: I3b6192815201f605d3ebdb4bf54db26a8e837b35
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fix for all Sandy-Bridge and Ivy-Bridge devices.
Remove unused option "hyper_threading".
Increase CMOS checksum range to cover all user adjustable settings.
Change-Id: I02f7af13d9c82d7f531d4b49b3bc0e5a20c14b55
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This is to align with the SD_CD GpioInt setting in acpi
BUG=b:62067569
TEST=checked unused interrupt on SD_CD does not happen after s3 resume
Change-Id: I40aefcb0f571e7f6773a6d20226f357707aa041a
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/20001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Like HAVE_VGA_TEXT_FRAMEBUFFER, these are selected by graphics drivers
that support a linear framebuffer. Some related settings moved to the
drivers (i.e. for rockchip/rk3288 and nvidia/tegra124) since they are
hardcoded.
Change-Id: Iff6dac5a5f61af49456bc6312e7a376def02ab00
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
* Rename it to HAVE_VGA_TEXT_FRAMEBUFFER.
* Let drivers select it if they are in charge.
* Don't select it on the mainboard level if a driver handles it.
Change-Id: I2d9d09be9aa6d019e77460e69a245ad2d8cda4ea
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The separate directory was the old way of handling variant boards.
Update bakersport_fsp to the new method. All of the other pieces
were already moved into bayleybay_fsp.
Change-Id: I5712c1b399570bd7ab7fc9e42af25fbf15a0ba78
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/19077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Light sensor isn't used and ACPI already removed, so disable
I2C5 bus interface as well.
Disable I2C6 for devices without a touchscreen
Change-Id: Ib0e041ae9131615ef1140bad064de5aae91f8ee4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19956
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Remove MONOTONIC_TIMER_MSR selection from mainboard
Konfigs, as it only does a reduntant selection of
HAVE_MONOTONIC_TIMER config, already selected under
skylake soc Kconfig.
Change-Id: Ib3177ceb9e8b6c16ce0e437a4a02b94f215af58f
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/20002
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
This board is almost identical to D510MO, the only differences are
some differences in populated connections, CPU with less L2 cache and
a 10/100 Realtek NIC.
The vendor uses the very same binary for both D510M0 and D410PT.
Change-Id: I220515365b69e785ef249c4e3a9af5f7fddf02f9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Enable H1 I2C TPM in Kconfig and devicetree for poppy.
CQ-DEPEND=CL:513513,CL:*381534
BUG=b:36265511
BRANCH=None
TEST=Compiles successfully.
Change-Id: I4c6c94fa05abf9f5374505ded5956e879ac79726
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nicolas Boichat <drinkcat@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=b:62147763
Change-Id: Iba88fed972b847448e01fcfca8c7129d950244c2
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19953
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each slippy variant has slightly different USB port config;
data for falco and leon to be added once available
Change-Id: Icc3b5b1161f62ac0b840380679acafeff363cf45
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
All beltino variants use the exact same USB port layout.
Change-Id: If5b540949ea071f7165876e12ac1ef50e62d2b22
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Move inclusion of mainboard.asl after southbridge asl files
so scopes referenced in usb.asl are valid.
Change-Id: I58ea0b43f7f2c2692630df3bdb06af92566c1202
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Port 0 is connected to SD-card reader.
Don't mark it as hot-plugable.
Change-Id: I5d3d4c7541683a6c09aac47ca251a6dad23ad1ab
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
To unify the hwinfo handling along all Siemens MC boards the hwinfo
files have to be removed from the mainboard directory. They will be added
to cbfs in site-local/Makefile.inc.
Change-Id: Ia3dcb2e0118527b37aed872740273c4fa7004aef
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The prior used RTC PCF8523 is replaced with RX6110SA on this mainboard.
Switch to the new RTC in Kconfig and adapt devicetree to the new chip.
Change-Id: I7c4911191cae254900f9a958da42ecd18497484c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Modify the DPTF configuration on Eve to relax the severe throttling that
is currently applied and allow performance testing to see better results.
BUG=b:35581264
TEST=performance tests show better results and thermal tests still pass.
Change-Id: I0838f4ec3026bc8bac814698043fa97cf6772cb4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Instead of having the SMI handler power off the touchscreen on the
way into suspend add power resource controls to the ACPI device so
the power is managed by the kernel instead of the BIOS.
BUG=b:35581264
TEST=manual testing on Eve to ensure that the touchscreen is still
functional at boot and after suspend/resume, and that it does not
draw power in suspend.
Change-Id: Id9a98807d24bbc7dff32408f3d113f6fad5bc023
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The Tegra210 SoC never had a proper cpu_reset() implementation, so it's
pointless to pretend there is one. Most ARM SoCs/boards only define
hard_reset() at the moment anyway, so let's stick with that.
Change-Id: I40f39921fa99d6dfabf818e7abe7a5732341cf4f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Get rid of mainboard_io_trap_handler.
The only purpose is to enable tp-smapi, but is already done on all
boards in h8_enable, as of devicetree setting config0.
Change-Id: I33fd829a7e34aefa8f76ca6020cc8e802f7aab17
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Instead of assuming the mapping of dimm number to SPD SMBus address,
allow the mainboard to provide its own mapping. That way, global
resources of empty SPD contents aren't wasted in order to address
a dimm on a mainboard that doesn't meet the current assumption.
Change-Id: Id0e79231dc2303373badaae003038a1ac06a5635
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
GPP_C2 is being used as strapping option, so
should not be set to NF. Signal was floating
previously, which can lead to an assertion of
smbalert#.
BUG=b:37681121, b:35775024
BRANCH=None
TEST=powerd_dbus_suspend and ensure stays in suspend
Change-Id: I68091206014621419b886b723a5681541be989bc
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19904
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Do not enable touchscreen device by default in gpio configuration.
2. Select use of PowerResource for touchscreen device in devicetree so
that the ACPI subsystem can take care of powering on/off the
device. When system enters suspend, touchscreen device is powered off
and on resume, it is powered back on.
BUG=b:62028489
TEST=Verified 100 cycles of suspend-resume. Touchscreen still works on
poppy.
Change-Id: Ia0bebc7259b10cc60a9fa5b53542dfdd9685663e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19829
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Should result in a tiny speed bump in raminit since those addresses
are not checked for present DIMMs.
Checked in schematics of both Thinkpad X60 and T60 and tested to
configure raminit correctly for all DIMMs populated on X60.
Change-Id: I56c4f3176541bc75a8de3aac9f87526a77fc819b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Change-Id: Ia44097f32f74ffd749219415984224ce33d9252b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Update Psi2Threshold, IccMax, AcLoadline, DcLoadline
VR config settings as per board design.
BUG=b:38415991
BRANCH=none
TEST=Build and boot eve.
Change-Id: I274245821f68fb3151e5563ea0c75eaa1ad32c08
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/19826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Soraka uses OV 13858 sensor. Hence update the same.
Change-Id: I4dd39a25da47e379cca3f8748250b3ce1ff61e50
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/19639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
