aboutsummaryrefslogtreecommitdiff
path: root/src/mainboard
AgeCommit message (Collapse)Author
2021-02-07mb101: fix cmos.layoutEvgeny Zinoviev
2021-02-07mb101: add ME CMOS optionsEvgeny Zinoviev
2021-02-07Merge branch 'me-disable' into mbp101_medisable_1Evgeny Zinoviev
2021-02-07Merge branch 'macbookpro10_1' into mbp101_medisable_1Evgeny Zinoviev
2021-02-07sb/intel/bd82x6x: Support ME Soft Temporary Disable ModeEvgeny Zinoviev
- Add support for ME Soft Temporary Disable Mode. In this mode, ME doesn't load its kernel and freezes at Bring UP (BUP) phase. This mode is saved in ME NVRAM (and thus will remain for next reboots and poweroffs). - Add support of new CMOS option for Sandy Bridge and Ivy Bridge ThinkPads. HOW TO USE To disable ME: 1. nvramtool -w me_state=Disabled 2. reboot To enable it back: 1. nvramtool -w me_state=Normal 2. reboot To check current status: intelmetool -m Tested on ThinkPad X230 and ThinkPad X220. BACKGROUND There's no Intel documentation that would explain how this should be implemented, in public. Working binary sequence for MKHI command to put ME in Soft Temporary Disable Mode, as well as a way to bring ME out of it (by writing to H_GS register), was found and published by researchers from PT Security: 1. To disable ME, BIOS issues the disable command (before End of Post) and reboots. ME is supposed to be disabled on the next boot after DID (DRAM Init Done). My numerous tests show that issuing the command and rebooting is not enough. If we reboot too early, ME will not be disabled. Apparently, it is doing something in background after receiving the command. It works with a delay of 500-1000 ms. I also tried to dump all known (documented) registers, such as GMES and HFS, before and during the next 2 seconds after execution of the disable command to find a possible indication that something's changed in ME and we're ready to reboot. Found nothing unfortunately. 2. To enable ME back, host writes value 0x20000000 to H_GS. PT slides don't contain any more information on it, but my tests show, that after writing this value, GMES[31:28] is changing from 0x01 (BUP phase) to 0x03 (Policy Module) to 0x06 (Host Communication). Then, after some more time, fw_init_complete bit of HFS becomes 1. This means that ME starts loading its kernel immediately, without reboot. On the other hand, Lenovo BIOS clearly perform a reboot after enabling it (one reboot after saving the settings, then ThinkPad logo appears, and then one more reboot). I'm assuming we have to reset too. Change-Id: Ic01526c9731cbef4e8552bbc352133a2415787c2 Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
2021-02-06mb/emulation/qemu-q35: Mark TSEG region as reservedPatrick Rudolph
Mark TSEG as reserved, which is done on other platforms as well. For some reason CorebootPayloadPkg crashes when using the region where TSEG typically resides, which is basically RAM. UefiPayloadPkg doesn't show this issue. Change-Id: I3ae3659349d2a88bc3575fe9675433c054e28832 Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50267 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-02-06mb/google/kukui: Add byte mode/single rank DRAM support for burnet/escheKevin Chiu
ID#5: Hynix - H9HCNNNFAMMLXR-NEE (Byte mode) ID#7: MICRON - MT53E1G32D2NP-046 WT:A (Single rank) BUG=b:165768895 BRANCH=kukui TEST=1. emerge-jacuzzi coreboot 2. power on test ok Change-Id: Iaa735c23889860218f6f6571cf0bc0b21b304b51 Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50276 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com>
2021-02-06mb/intel/shadowmountain: Add bootblock and verstage codeV Sowmya
This patch includes the bootblock and verstage changes for shadowmountain board. BUG=b:175808146 TEST= Build and boot shadowmountain board till early romstage. Signed-off-by: V Sowmya <v.sowmya@intel.com> Change-Id: I5f805baf42203306ff10e91a258d9117dd986c4a Reviewed-on: https://review.coreboot.org/c/coreboot/+/49479 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
2021-02-06mb/google/zork: Adjust Dirinboz H1 I2C CLKKevin Chiu
Adjust H1 I2C CLK: 404kHz -> 391 kHz BUG=b:178656936 BRANCH=master TEST=1. emerge-zork coreboot chromeos-bootimage 2. power on proto board successfully 3. measure i2c freq by scope is close to 400kHz Change-Id: I9067db9fc7a4d6aa2ce33b86ba6a611dfd5d7838 Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50284 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Kangheui Won <khwon@chromium.org>
2021-02-06mb/google/dedede/var/galtic: Configure I2C high and low timeFrankChu
Configure the I2C bus high and low time for all enabled I2C buses. BUG=b:179100924 TEST=Measured the I2C bus frequency as 384 KHz, high time as 924 ns and low time as 1680 ns. Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com> Change-Id: I1525ecbf5baf9ae169afd7ce59079f395a2a45a8 Reviewed-on: https://review.coreboot.org/c/coreboot/+/50211 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2021-02-06mb/google/guybrush: First pass GPIO configuriation for GuybrushMathew King
BUG=b:175143925 TEST=builds Signed-off-by: Mathew King <mathewk@chromium.org> Change-Id: Ia8211dbc3de09a61f264a0e5d44d1eac703b83c9 Reviewed-on: https://review.coreboot.org/c/coreboot/+/50091 Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-06mb/google/guybrush: Add stubs to configure GPIOsMathew King
BUG=b:175143925 TEST=builds Signed-off-by: Mathew King <mathewk@chromium.org> Change-Id: I5afd2df396ba41f7d25fa7ff6879b7c1f82f438c Reviewed-on: https://review.coreboot.org/c/coreboot/+/49954 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-02-05soc/amd/picasso: add UPD for RV2 USB3 phy setting adjustChris Wang
add UPD for RV2 USB3 phy setting adjust. Note: it only for RV2 silicon and not available for RV/PCO. Usb 3.1 PHY Parameters: 1. RX_EQ_DELTA_IQ_OVRD_VAL -Override value for rx_eq_delta_iq. Range 0-0xF 2. RX_EQ_DELTA_IQ_OVRD_EN -Enable override value for rx_eq_delta_iq. Range 0-0x1 3. Override value for rx_vref_ctrl. Range 0 - 0x1F 4. Enable override value for rx_vref_ctrl. Range 0 - 0x1 5. Override value for tx_vboost_lvl: 0 - 0x7. 6. Enable override value for tx_vboost_lvl. Range: 0 - 0x1 7. Override value for rx_vref_ctrl. Range 0 - 0x1F 8. Enable override value for rx_vref_ctrl. Range 0 - 0x1 9. Override value for tx_vboost_lvl: 0 - 0x7. 10. Enable override value for tx_vboost_lvl. Range: 0 - 0x1 BUG=b:175192931 TEST=Build/verify the valule will been apply on dirinboz Change-Id: I1d5f69e840952cc5171af1ce8597628d1bede5cb Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50240 Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Kangheui Won <khwon@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-05mb/gigabyte/ga-h61m-series: Drop broken thermal.aslAngel Pons
Was copy-pasted from another board and causes ACPI errors on Linux. Change-Id: I9d62462fb7ddc788d08489bf82b110aeae6a1ffc Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49927 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-by: Nico Huber <nico.h@gmx.de>
2021-02-05mb/google/zork: update telemetry settings for WoomaxKane Chen
Improve performance and meet stardust test requirement. PcdSet32(PcdTelemetry_VddcrVddfull_Scale_Current,102586) PcdSet32(PcdTelemetry_VddcrVddOffset, 0) PcdSet32(PcdTelemetry_VddcrSocfull_Scale_Current,24674) PcdSet32(PcdTelemetry_VddcrSocOffset, 0) BUG=b:176156237 BRANCH=zork TEST=emerge-zork coreboot Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com> Change-Id: I81dbfafffe7625c3d0d80419466240508f9b041b Reviewed-on: https://review.coreboot.org/c/coreboot/+/50256 Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-05mb/google/brya: Add support for Hynix H9HCNNNBKMMLXR-NEE LP4x DRAMTim Wawrzynczak
BUG=b:178681161 TEST=abuild Change-Id: Icccfa3d1659e6c74c14a7372ea39c749a5921c64 Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50271 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2021-02-05mb/apple/macbookair4_2: Add ACPI support for ECEvgeny Zinoviev
Add ACPI support for battery, AC and lid. I don't have MacBook Air 4,2 to test, but: - I tested it on 5,2; - I found decompiled DSDT for 4,2 and compared registers and bits, they are the same as on 5,2. So it should work. Change-Id: I592cb4501c878fe46684a524e729d32fb1d7920c Signed-off-by: Evgeny Zinoviev <me@ch1p.io> Reviewed-on: https://review.coreboot.org/c/coreboot/+/33103 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-02-05soc/intel/alderlake: Refactor PCIE port configEric Lai
Refactor PCIE port config structure. Make it easier to map from schematic. We don't have to convert the PCIE ports RP number and CLK source in devicetree. All the convert will be done by SoC level. Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: I0b390e43f8e99b19cfad178139b86a2f77d7a57b Reviewed-on: https://review.coreboot.org/c/coreboot/+/48340 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-02-05intel: Turn `DEFAULT_RCBA` into a Kconfig symbolAngel Pons
Create `FIXED_RCBA_MMIO_BASE` and use it everywhere, except in cases where a pointer cast would be necessary. Instances in Sandy Bridge MRC code were left as-is intentionally, so as not to collide with another cleanup patch train. Tested with BUILD_TIMELESS=1, these boards remain identical: - Asus P8Z77-V LX2 - Packard Bell MS2290 Change-Id: I642958fbd6f02dbf54812d6a75d6bc3087acc77a Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50036 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-05mb/google/dedede: Create kracko variantTony Huang
Create the kracko variant of the waddledee reference board by copying the template files to a new directory named for the variant. (Auto-Generated by create_coreboot_variant.sh version 4.5.0). BUG=b:178092096 BRANCH=dedede TEST=util/abuild/abuild -p none -t google/dedede -x -a make sure the build includes GOOGLE_KRACKO Change-Id: I7f8c7a4d4967e99896166ec9dd6b7381b7f6e5ed Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50255 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2021-02-04mb/google/zork/variants/vilboz: Enable BayHub lv2 driverJohn Su
Enable this driver along with power saving. BUG=b:177955523 BRANCH=zork TEST=boot and see this message: BayHub LV2: Power-saving enabled 110102 Signed-off-by: John Su <john_su@compal.corp-partner.google.com> Change-Id: Icd87ea585dfaa2185abf1f7bf803e9c9a6e63972 Reviewed-on: https://review.coreboot.org/c/coreboot/+/49822 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-02-04drivers/intel/fsp2_0: Fix running on x86_64Patrick Rudolph
Add new Kconfig symbols to mark FSP binary as x86_32. Fix the FSP headers and replace void pointers by fixed sized integers depending on the used mode to compile the FSP. This issue has been reported here: https://github.com/intel/FSP/issues/59 This is necessary to run on x86_64, as pointers have different size. Add preprocessor error to warn that x86_64 FSP isn't supported by the current code. Tested on Intel Skylake. FSP-M no longer returns the error "Invalid Parameter". Change-Id: I6015005c4ee3fc2f361985cf8cff896bcefd04fb Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48174 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-02-04mb/google/volteer: update thermal table for EldridNick Chen
1. Add pl4 value 2. Change policies passive with sensor 0 and 1 3. Change granularity value with pl1 and pl2 BUG=b:178768749 TEST=make buildall Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com> Change-Id: I2f1fe9a6de4dbb587b79cb8758c5458a3ae5d768 Reviewed-on: https://review.coreboot.org/c/coreboot/+/50111 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-04mb/prodrive/hermes: Use some board settings from EEPROMAngel Pons
Cache the board settings in memory to avoid having to read them from the EEPROM multiple times. For now, configure the following settings: - DeepSx - USB power in S5 - Power state after G3 Change-Id: Id88529a0b064c54fdf341de3856a8877109d4b14 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48807 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2021-02-04mb/prodrive/hermes: Define board settings in EEPROMAngel Pons
Hermes has an EEPROM with firmware configuration data. Add definitions to read and verify the `board settings` from the EEPROM. Subsequent commits will hook up these EEPROM settings. Change-Id: Id86632192ae53fd6b0e4df5b26b5a0a81e972818 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48806 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2021-02-04mb/google/kukui: kakadu: update the initial code for BOE LCDSunway
The latest initial code is from BOE, the vendor. BUG=b:179206650 BRANCH=kukui TEST=Run long time aging test and the BOE LCD shows normally. Signed-off-by: Sunway <lisunwei@huaqin.corp-partner.google.com> Change-Id: Ibc1bd5147dbda4e3b94023e7ba52ff6a18abba0c Reviewed-on: https://review.coreboot.org/c/coreboot/+/50215 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-04src: Remove useless comments in "includes" linesElyes HAOUAS
Change-Id: Ide5673dc99688422c5078c8c28ca5935fd39c854 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50186 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-02-04mb/clevo/cml-u/bootblock.c: Remove unused includesElyes HAOUAS
Change-Id: I048e906306bf77a941b5f731ade15292fa944390 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50219 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Singer <felixsinger@posteo.net> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-02-04mb/amd/{parmer,thatcher}/bootblock.c: Remove unused includesElyes HAOUAS
Change-Id: I4d5520649addc671527e75f9090ea45a83b5db9b Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50218 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-02-04mb/amd/majolica: add fmd for use when building chromeosMathew King
BUG=b:177909472 TEST=builds Change-Id: I5eb3c60fe60e4029485fae642c88c5c013ffb3f6 Signed-off-by: Mathew King <mathewk@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50208 Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-04mb/emulation/qemu: Fix SMP bootPatrick Rudolph
Fix booting with SMP enabled, when specifying more CPUs than supported by the code. Change-Id: Ib3d7c1a1a7a8633d4d434ccbd46cf92b0074b724 Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50235 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2021-02-04src: Remove unused <bootstate.h>Elyes HAOUAS
Change-Id: I0d2ab4144970184f46e1d0e7a2464e94fa38aa63 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50203 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com> Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
2021-02-04src: Remove unused <cbfs.h>Elyes HAOUAS
Change-Id: Idc11f1e131df2e01864fedac864bda5e11f2d17b Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50166 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2021-02-04mb/google: Convert some CONFIG(CHROMEOS) preprocessorKyösti Mälkki
Change-Id: Ica8691e3dc4feecbeb11ba3f5868932f926965b2 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48785 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-04mainboards: Remove default CHROMEOS=yKyösti Mälkki
Even the boards with MAINBOARD_HAS_CHROMEOS need to be build-tested with CHROMEOS=n. Change-Id: I16fcf62a23dae1b21c77cee275c867f9c1de893b Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50118 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
2021-02-04vc/google/chromeos: Drop <acpi/vpd.asl>Kyösti Mälkki
This was used as a means to read the MAC address and dynamically return it to the ethernet driver via ACPI. The kernel team ended up going another direction so this became obsolete. Change-Id: I7065bea4b288c689b41cc969989ec6fd87c75f1f Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49902 Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-03mb/google/volteer/variants/drobit: Configure USB2 port for Type-CHEADmasterWayne3_Wang
USB2 ports assigned to type-C connector need to be configured properly by the USB2_PORT_TYPE_C. and also modify the description of USB port. BUG=b:177480902 BRANCH=firmware-volteer-13672.B TEST=emerge-volteer coreboot chromeos-bootimage build Pass And check the typeC port function is normal by manual. Signed-off-by: Wayne3_Wang <Wayne3_Wang@pegatron.corp-partner.google.com> Change-Id: I9e962f8cd76e1986700821168594c50bc21553e9 Reviewed-on: https://review.coreboot.org/c/coreboot/+/50217 Reviewed-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-03mb/google/volteer/var/voema: Enable EEPROM for OV2740David Wu
Add ACPI entries for AT24 NVM device. BUG=b:169551066 TEST=Build and run for basic camera functions. Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: Ib8fb684166649f78713050d62445bf47189b06ab Reviewed-on: https://review.coreboot.org/c/coreboot/+/50216 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jim Lai <jim.lai@intel.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-02-03mb/apple: Add MacBook Pro 10,1 (A1398) supportEvgeny Zinoviev
MacBook Pro 15 (Mid 2012) with Ivy Bridge CPU and Retina Display. Used autoported config as a template. Change-Id: Ica03aba442493c0d369a3d360ad569ddc16954df Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
2021-02-03soc/amd/picasso: clean up and re-sort UPD tableChris Wang
Clean up the unused UPD and re-sort the table, and also update the new phy parameter in the soc code and overridetree. remove: EDpPhySel EDpVersion rename: DpPhyOverride -> edp_phy_override EDpPhySel -> edp_physel DpVsPemphLevel -> edp_dp_vs_pemph_level MarginDeemPh -> edp_margin_deemph Deemph6db4 -> edp_deemph_6db_4 BoostAdj -> edp_boost_adj eDP phy setting: DP_VS_LEVEL0_PREEMPH_LEVEL0 = 0x00(0.4v 0db swing 0,pre-emphasis 0) COMMON_MAR_DEEMPH_NOM = 0x004b COMMON_SELDEEMPH60 = 0x0 CMD_BUS_GLOBAL_FOR_TX_LANE0 = 0x80 BUG=b:171269338 BRANCH=zork TEST=Build, verify the parameter pass to picasso-fsp Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com> Change-Id: I655af08e2f86398d088e30d330f49e71cf7e1275 Reviewed-on: https://review.coreboot.org/c/coreboot/+/50212 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2021-02-03mb/google/volteer/variant/copano: support regular/numpad touchpadZhuohao Lee
Define the 25th bit of the fw_config for the regular touchpad and numpad touchpad selection. BUG=b:174027837 BRANCH=firmware-volteer-13672.B TEST=build pass Change-Id: Ic5d61f19fd385600cfdcdd045dab1e61b06e4663 Signed-off-by: Zhuohao Lee <zhuohao@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50129 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Marco Chen <marcochen@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-02-03src: Remove unused <boardid.h>Elyes HAOUAS
Change-Id: I960870fabde1dacfe52a8a35c253b0bd097d3e10 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50183 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2021-02-03mb/google/volteer/variants/drobit: Modify touchpad I2C sequenceWayne3_Wang
Modify touchpad I2C sequence to meet requirement. BUG=b:178512111 BRANCH=firmware-volteer-13672.B TEST=emerge-volteer coreboot chromeos-bootimage build Pass And check the touchpad I2C5 sequence by EE. Signed-off-by: Wayne3_Wang <Wayne3_Wang@pegatron.corp-partner.google.com> Change-Id: Iebbeeec51b802c318ac014dcdd2603b600d931a9 Reviewed-on: https://review.coreboot.org/c/coreboot/+/49958 Reviewed-by: Zhuohao Lee <zhuohao@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Hao Chou <hao_chou@pegatron.corp-partner.google.com> Reviewed-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-03mb/google/volteer/variants/drobit: Add TBT PCIE rp setting for drobitWayne3_Wang
Add the TBT PCIE rp setting to on and also fixes system hang in recovery screen after selected "Power off" item problem. BUG=b:177963941 BRANCH=firmware-volteer-13672.B TEST=emerge-volteer coreboot chromeos-bootimage build Pass And check the system can power off normally in recovery page Cq-Depend: chrome-internal:3581043 Signed-off-by: Wayne3_Wang <Wayne3_Wang@pegatron.corp-partner.google.com> Change-Id: Ic0a4756b4af839ea0a23febb991bd71af7733dcc Reviewed-on: https://review.coreboot.org/c/coreboot/+/50103 Reviewed-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com> Reviewed-by: Ariel Chang <ariel_chang@pegatron.corp-partner.google.com> Reviewed-by: Zhuohao Lee <zhuohao@chromium.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-03hatch: Update fan and thermal settings for ambassadorNeill Corlett
Update fan and thermal settings for ambassador, per recommendations from Quanta. BUG=b:177765580 TEST=Built AP firmware Change-Id: I080859f872caf696f0c085defb8372de658da58a Signed-off-by: Neill Corlett <corlett@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50100 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Joe Tessler <jrt@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-03mb/biostar/th61-itx/early_init.c: Clean includesElyes HAOUAS
Change-Id: I0619e567527812bd0e7088d23d91f114c8fec9ec Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50200 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2021-02-03mb/google/sarien: Turn `hda_verb.h` into `hda_verb.c`Angel Pons
Change-Id: I40c8145fdddf9605bc3cc66ae8075e52dca4e539 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50175 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-02-02mb/siemens/mc_apl1: do UART pad configuration at board-levelMichael Niewöhner
UART pad configuration should not be done in common code, because that may cause short circuits, when the user sets a wrong UART index. Thus, add the corresponding pads to the early UART gpio table for the board as a first step. Common UART pad config code then gets dropped in CB:48829. Also switch to `bootblock_mainboard_early_init` to configure the pads in early bootblock before console initialization, to make the console work as early as possible. The board does not do any other gpio configuration in bootblock, so this should not influence behaviour in a negative way (e.g. breaking overrides). Change-Id: Iac8a6e386b708ae5c4dbf0677bfe05f1358bf8fd Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49442 Tested-by: siemens-bot Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-02-02treewide [Kconfig]: Remove useless commentElyes HAOUAS
Change-Id: I3dafffa61f4fe6089fd11ef6579626aff8088df5 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50185 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-02-01mb/pcengines/apu2: Switch to proper GPIO APIKyösti Mälkki
Use the abstractions <gpio.h> provides. Change-Id: I348ba43a76287be5b24012ae3dfc28ed783da9c7 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/42521 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
2021-02-01sb/intel/i82801ix: Factor out common `acpi_fill_madt`Angel Pons
It is the same for all three mainboards. Change-Id: Ic5786bcc29e2549d6fc935d60c699c1cab84b237 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50027 Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-01mb/google/dedede/variants/drawcia/variant.c: Remove unused <bootstate.h>Elyes HAOUAS
Change-Id: I38d115f2c405128a8d80aec48d2d9d3f25867151 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45815 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-01mb/google/{butterfly,link,rambi,stout}: Remove unused <acpi/acpi_gnvs.h>Elyes HAOUAS
Change-Id: If5c35f3518e2cc4d5760a64e0d38fc4843af498a Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50164 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-01soc/intel/alderlake: Create separate Kconfig for CLKSRC and CLKREQSubrata Banik
As per Hardware Architecture Specification (HAS) ADL-P has 7 CLKSRC and 10 CLKREQ (7 SRCCLK is internal and 3 SRCCLK from external CLK chip). ADL-M has 6 SRCCLK and CLKREQ (no external CLK chip). Change-Id: I7d223c165f819669722cbc80245fa8ec20372352 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50130 Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-01mb/google/dedede/var/magolor: Configure Acoustic noise mitigation UPDsRen Kuo
Enable Acoustic noise mitigation for magolor and set slew rate to 1/8 which is calibrated value for the board. BUG=b:178678267 BRANCH=dedede TEST=build firmware to UPD and Acoustic noise test Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com> Change-Id: Idea2a801399bb5c7e0b8e59ee7a826c86a44f4ea Reviewed-on: https://review.coreboot.org/c/coreboot/+/50099 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-01drivers/security/cbnt: Fix bootblock sizeArthur Heymans
Change-Id: Ic5ad9d29f247b6f828501bfacc27a8af08761d55 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50082 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jonathan Zhang <jonzhang@fb.com> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2021-02-01mb/google/brya: Initiate peripheral busesEric Lai
Initiate peripheral buses based on latest schematic. BUG=b:174266035 TEST=Build Test Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: Ibf48aceca7ac8774b0353e31bd81e1880c4066ea Reviewed-on: https://review.coreboot.org/c/coreboot/+/49007 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-02-01mb/google/volteer: Select SOC_INTEL_CSE_LITE_SKU for volteer baseboardFurquan Shaikh
This change moves the selection of SOC_INTEL_CSE_LITE_SKU into Kconfig under BOARD_GOOGLE_BASEBOARD_VOLTEER instead of requiring each individual board to select it. TEST=Verified that timeless build does not result in any changes. Change-Id: I2d94931fdc3077794bed5cc51708b5a5d9e64972 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50096 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-02-01mb/google/volteer: Drop boldar variantFurquan Shaikh
This variant never really got used and can be deprecated. Change-Id: I5d59460c90266ba5f9c3bdb951f53a37ffae9e03 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50095 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-02-01mb/google/brya: Change EC -> PCH wake pin to GPP_F17Boris Mittelberg
A new schematic revision indicates that the old wake pin is not used, and brya will only use 1 IRQ pin from EC, routed to GPP_F17 BUG=b:178605367 TEST=Build test Signed-off-by: Boris Mittelberg <bmbm@google.com> Change-Id: Ia2bc5b1562ab30b4461fc7e3b1a4bc3e370db588 Reviewed-on: https://review.coreboot.org/c/coreboot/+/50084 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-02-01Revert "mb/google/hatch/dratini: Describe the privacy_gpio"Ricardo Ribalda
This reverts commit f41645c34d8b22a3d887abd56138ae794fc2dfa5. In Dragonair, during the MP stage, one of the resistors needed for this functionality has been removed. This results in the privacy-switch not readable back by the system. BUG=b:178458332 Change-Id: I0781f338d5ecd89fccee613fb13ea25c59385625 Signed-off-by: Ricardo Ribalda <ribalda@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50044 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-02-01ipmi/ocp: Move common OCP/Facebook IPMI OEM codes into drivers/ipmi/ocpJohnny Lin
1. These are common OCP/Facebook IPMI OEM commands, move from mainboard into drivers/ipmi/ocp to avoid code duplication and provide better reusability. 2. OCP Tioga Pass enables IPMI_OCP driver. Tested=On OCP Delta Lake and Tioga Pass verify the commands still work correctly. Change-Id: Idd116a89239273fd5cc7b06c7768146085a3ed69 Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49235 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
2021-01-31mb/emulation/qemu-q35: Use common MADTAngel Pons
Select SOUTHBRIDGE_INTEL_COMMON_ACPI_MADT and drop the `acpi_fill_madt` function definition, which is redundant. Tested, still boots to payload. Change-Id: I6ba448f264a478e7ef060ea1dfbf5016a310d528 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50026 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Nico Huber <nico.h@gmx.de>
2021-01-31mb/emulation/qemu-q35: Define and use MMCONF_BUS_NUMBERAngel Pons
Also refactor the machine type checks to avoid code duplication. Tested, still boots to payload with 256, 128 and 64 busses. Change-Id: Ib394ba605bbfeee75aa645e989c23034cceff348 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50025 Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-30mb/amd/majolica: Add an empty bootblock function to handle GPIOZheng Bao
Change-Id: I35da3812a424ea1beef86d043a756a87e6afdaa3 Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50117 Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-30mb/amd/majolica: Add an empty function of mainboard bootblockZheng Bao
Change-Id: I985405b51c81d1e5a3a593bfb759e9850beb2244 Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50116 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2021-01-30mb/intel/adlrvp: Remove unnecessary whitespaceSubrata Banik
Change-Id: I46af3e789de10ca6951b9e17f286c094c08a477f Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50131 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2021-01-29mb/emulation/qemu-q35: Consolidate host bridge definitionsAngel Pons
Move all Q35 register definitions into the q35.h header. Note that real hardware does not have EXT_TSEG_MBYTES, because it is QEMU-specific. Change-Id: I4c86ac0bb05563dee111b9b4a4a71c1c31198acd Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50024 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-29mb/emulation/qemu-q35: Rename headerAngel Pons
The emulated northbridge is Q35. GM35 does not exist. Tested, still boots. Change-Id: Id8e114a43b54b71087d09d143176ed94329ab7af Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50023 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2021-01-29device/Kconfig: Declare MMCONF symbols' type onceAngel Pons
Only specify the type of MMCONF_BASE_ADDRESS and MMCONF_BUS_NUMBER once. Change-Id: Iacd2ed0dae5f1fb6b309124da53b3fa0eef32693 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50032 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-29mb/purism/librem_bdw: Turn comments into codeAngel Pons
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 does not change. Change-Id: Iec84fc2b43c23ea85f5cf13d9f0bace73e448c97 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49285 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2021-01-29mb/emulation/qemu-q35: Rename PICF to PICM in ASLKyösti Mälkki
Change-Id: I395056a164b6597b6fb3dfda0d85f9a0374cd893 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49998 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2021-01-28mb/google/butterfly: Convert to ASL 2.0 syntaxElyes HAOUAS
Generated 'build/dsdt.dsl' files are same. Change-Id: I85edf649a5170a1658fb135b797c1c6e1d2a9d70 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46171 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-01-28mb/gizmosphere/gizmo2: Convert to ASL 2.0 syntaxElyes HAOUAS
Generated build/dsdt.dsl files are same. Change-Id: I0a4af7ebe6114338c2e8fb5fdf39a1de2cd47138 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46168 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-01-28mb/gigabyte/ga-b75m-d3h: Convert to ASL 2.0 syntaxElyes HAOUAS
Generated 'build/dsdt.dsl' are identical. Change-Id: Ic9b7dfd786ff8e1512c8678590a1dad7c984bca8 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46165 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-01-28mb/hp/pavilion_m6_1035dx: Convert to ASL 2.0 syntaxElyes HAOUAS
Generated 'Build/dsdt.dsl' are identical. Change-Id: Id48df4fa0f8e5486636292ad11b8a86e71db4b17 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46080 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-28mb/asrock/e350m1: Convert to ASL 2.0 syntaxElyes HAOUAS
Generated 'build/dsdt.dsl' are identical. Change-Id: Ief7ea77f8081cd6b7fb18fbf1d25c7394daca07d Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46154 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-28mb/hp/abm: Convert to ASL 2.0 syntaxElyes HAOUAS
Generated 'Build/dsdt.dsl' are identical. Change-Id: Ie93dd1f6de1357cb3f448ed79a33b688abd91731 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46164 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-01-28mb/asrock/imb-a180: Convert to ASL 2.0 syntaxElyes HAOUAS
Generated 'build/dsdt.dsl' are identical. Change-Id: I100b6c596d8a1dd74f096f71675026618da32e6f Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46155 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-01-28mb/amd/thatcher: Convert to ASL 2.0 syntaxElyes HAOUAS
Change-Id: If1869d091f9c78db7e308143d96b5d3046510ac8 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46152 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-28mb/amd/parmer: Convert to ASL 2.0 syntaxElyes HAOUAS
Change-Id: I563cd549858429049223677ebc503f9c9304baa0 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46149 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-28mb/amd/padmelon: Convert to ASL 2.0 syntaxElyes HAOUAS
Change-Id: I88c1c907916c3de51f6b3b72f7a49e90a1b1a383 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46148 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-28mb/biostar/a68n_5200: Convert to ASL 2.0 syntaxElyes HAOUAS
Generated 'build/dsdt.dsl' files are same. Change-Id: I122f27bf7e7b809802efdbd443694b3d6e715108 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46076 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-01-28mb/elmex/pcm205400: Convert to ASL 2.0 syntaxElyes HAOUAS
Generated 'build/dsdt.dsl' files are same. Change-Id: I1cec4049adac74270641736709774156628b2539 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46162 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-01-28treewide: Remove unused #includes of spi_winbond.hDaniel Gröber
We want to add some function declarations as static_testable to this header but including it in a .c file outside of tests will yield a gcc warning like: error: 'function' declared 'static' but never defined [-Werror=unused-function] It seems these includes aren't necessary anyways so we just remove them. Change-Id: I17147136579140b94728ceb1c369b1348714bc53 Signed-off-by: Daniel Gröber <dxld@darkboxed.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44090 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Frans Hendriks <fhendriks@eltan.com> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
2021-01-28mb/system76/oryp5: Fix up DSDTPatrick Georgi
We started depending on dsdt_top.asl in dsdt.asl but this newly added board wasn't adapted yet, so have it catch up. Change-Id: If00280a33fd9e5c3ef1b3d07c41e81ed18013714 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50021 Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-28mb/emulation/qemu-q35: Solve lint-001 errorFrans Hendriks
lint-001-no-global-config-in-romstage error on D0F0_PCIEXBAR_LO. DOF0_PCIEXBAR_LO is defined in bootblock.c and romstage.c. Place D0F0_PCIEXBAR_XX in local gm35.h. BUG = N/A TEST = Build and boot QEMU x86 q35/ich9 Change-Id: Ia5ac9eb797de996186282193647313b9f7b42624 Signed-off-by: Frans Hendriks <fhendriks@eltan.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49930 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com> Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
2021-01-28mb/google/dedede/var/galith: Add Wifi SAR for convertiblesFrankChu
Add wifi sar for galith Using convertible mode of fw config to decide to load custom wifi sar or not. BUG=b:176206495 TEST=enable CHROMEOS_WIFI_SAR in config of coreboot, emerge-dedede coreboot-private-files-baseboard-dedede coreboot chromeos-bootimage. Cq-Depend: chromium:2649378,chrome-internal:3559387 Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com> Change-Id: I0f9a7ddedef550317da4bf798317619ffd1fa979 Reviewed-on: https://review.coreboot.org/c/coreboot/+/49923 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2021-01-28mb/intel/adlrvp: Configure SATA DEVSLP as per latest schematicsSubrata Banik
1. GPP_E5 => Remove unused GPIOs 2. GPP_H12, GPP_H13 => Program the correct Native Functions for GPIO Change-Id: I588a8c1153eaa1bf818a081c6c5d18a669017d95 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49964 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2021-01-28mb/google/parrot: Convert to ASL 2.0 syntaxElyes HAOUAS
Change-Id: Ie802b540cea13000227c969bbc262f034d1b6b84 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46177 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-01-28mb/google/asurada: Improve boot time by raising little CPU frequencyYidi Lin
Raise little CPU to 2GHz at romstage to improve boot time. BUG=b:177389446 TEST=observe boot time by `cbmem` Before: 1,062,359 us After: 907,458 us Signed-off-by: Yidi Lin <yidi.lin@mediatek.com> Change-Id: I723a916d7f708627525ef11e3c5ea0b381f269aa Reviewed-on: https://review.coreboot.org/c/coreboot/+/49935 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com>
2021-01-28mb/google/dedede/var/sasuke: Configure GPP_G7 as nativeSeunghwan Kim
Configuring GPP_G7 as NC causes SD card detection issue on sasuke. So we'd like to remove the GPP_G7 override and keep the baseboard configuration as native function (SDIO_WP). BUG=b:175831709 BRANCH=firmware-dedede-13606.B TEST=Built and verified SDR104 SD card operation on sasuke Change-Id: If73337b482f04fd263caaa6fed0e54aa87bd876e Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49791 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jamie Chen <jamie.chen@intel.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2021-01-28bayhub bh720: Factor out common HS200 init codeAngel Pons
Except for one debug print in sarien, both functions are identical. Move them to driver code to avoid unnecessary redundancy. Change-Id: I82635a289e3c05119eab4ee1f7a6bf3a8a1725c1 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49833 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
2021-01-28mb/google/asurada: Add config for spherionYu-Ping Wu
BUG=b:178440482 TEST=emerge-asurada coreboot BRANCH=none Change-Id: Ica09b73f97509db065c93c6be757c0d77c9b7a87 Signed-off-by: Yu-Ping Wu <yupingso@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49956 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2021-01-28mb/emulation/qemu-i440fx: Convert to ASL 2.0 syntaxElyes HAOUAS
Generated 'build/dsdt.dsl' files are identical. Change-Id: I9157d9fc61339792dbbc45e82e1cb04fa51c6aae Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46077 Reviewed-by: Patrick Rudolph <siro@das-labor.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-28mb/emulation/qemu-q35: Convert to ASL 2.0 syntaxElyes HAOUAS
Generated 'build/dsdt.dsl' files are identical. Change-Id: I4e0f64def6c4c712793d3b2ede99dd74f9046fcb Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46163 Reviewed-by: Patrick Rudolph <siro@das-labor.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-28mb/google/volteer: Add GL9755 support to DrobitWayne3_Wang
Add the GL9755 support to drobit and also fixes the S0ix can't into C3~C9 problem BUG=b:174348200 BRANCH=firmware-volteer-13672.B TEST=emerge-volteer coreboot Signed-off-by: Wayne3_Wang <Wayne3_Wang@pegatron.corp-partner.google.com> Change-Id: I52df6b2cdebfaf8a5eb010c4af1a2cf3d918f5e5 Reviewed-on: https://review.coreboot.org/c/coreboot/+/49921 Reviewed-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com> Reviewed-by: Paul2 Huang <paul2_huang@pegatron.corp-partner.google.com> Reviewed-by: Zhuohao Lee <zhuohao@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-28mb/google/brya: Add variants overridetree.cb path and remove unused registersEric Lai
Add variants overridetree.cb path remove unused registers BUG=b:174266035 TEST=Build Test Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: I2940332044aa4c2de6d58f5d0d2a2a7c1b2c3478 Reviewed-on: https://review.coreboot.org/c/coreboot/+/49920 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-01-28mb/google/zork: add MST details to trembyle devicetreeShiyu Sun
Added device hid info to the MST RTD2141b device on trembyle. BRANCH=zork BUG=b:147402710 TEST=Build and flash BIOS image, see 10EC2141 appears under /sys/bus/i2c/devices Signed-off-by: Shiyu Sun <sshiyu@chromium.org> Change-Id: I97a67f9dbc31cd788d579252d7d355b24d97ca30 Reviewed-on: https://review.coreboot.org/c/coreboot/+/48229 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Sam McNally <sammc@google.com>
2021-01-28mb/system76/oryp5: Add System76 Oryx Pro 5Tim Crawford
Tested with TianoCore payload (UefiPayloadPkg). Working: - PS/2 keyboard, touchpad - Both DIMM slots - Both NVMe ports - SATA port - All USB ports - Webcam - Ethernet - Integrated graphics - Internal microphone - S3 suspend/resume - Flashing with flashrom - Booting to Ubuntu Linux and Windows Not working: - Discrete/Hybrid graphics - Internal speakers These two require new drivers to work correctly, which will be added and enabled later. Change-Id: Iae6e530dcd52df3642cdfe74b65bfff5aa0dd402 Signed-off-by: Tim Crawford <tcrawford@system76.com> Signed-off-by: Jeremy Soller <jeremy@system76.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47892 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-06-30 22:38:39 +0000