Age | Commit message (Collapse) | Author |
|
Enable all PCIe root ports for this mainboard.
Change-Id: I7f6feb2f0d4c45f32d9454838e67e1a244b2712b
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
There is no device on I2C0 which requires a lower clock rate.
Change-Id: Ib7c4e3251545b2d32368dd56206e3b4844a24800
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
All PCIe root ports of this mainboard do not have an associated CLKREQ
signal. Therefore the ports are marked with "CLKREQ_DISABLED".
Change-Id: I834b3b0c77223d81c950e27ccfff8e9aeece2aa4
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
On this mainboard there are legacy PCI device, which are connected to
different PCIe root ports via PCIe-2-PCI bridges. This patch disables
the unused PCI clock outputs on the XIO2001 PCI Express to PCI Bridges.
Change-Id: I2212c1080b72a656b5c8e68b040108a7adbec608
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard provides customer hardware reset button. A feature of
this button is that it holds the APL in reset state as long as the reset
button is pressed. After releasing the reset button the APL should
restart again without the need for a power cycle. When Bit 3 in Reset
Control Register (I/O port CF9h) is set to 1 and then the reset button
is pressed the PCH will drive SLP_S3 active (low).
Change-Id: Ib842f15b6ba14851d7f9b1b97c83389adc61f50b
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29530
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
There is an on-board PCI device where bus master has to be enabled in
PCI configuration space. As there is no need for a complete PCI driver
for this device just set the bus master bit in mainboard_final().
Change-Id: I1ef4a7774d4ca75c230063debbc63d03486fed6f
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
For this mainboard the correction of transmit voltage swing from SATA
interface is not necessary.
Change-Id: I900d0d44b88585c223182d85c78cf3ff1e3e9159
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
On this mainboard there is a legacy PCI device, which is connected to
the PCIe root port via a PCIe-2-PCI bridge. This device only supports
legacy interrupt routing. For this reason we have to adjust the PIR6
register (0x314c) which is responsible for PCIe device 13h and 14h. This
means that the interrupt routing will also be the same for both PCIe
devices. The bridge is connected to PCIe root port 2 and 3 over two
lanes (Device 13.0 and 13.1).
The following routing is required:
INTA#->PIRQD#, INTB#->PIRQA#, INTC#->PIRQB#, INTD#->PIRQC#
Change-Id: I5028c26769a2122b1c609ad7789c9949e3cb7a87
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29513
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change tcc offset from 0 to 10 for fleex.
Refer to b:117789732#1
BUG=b:117789732
TEST=Match the result from TAT UI
Change-Id: I481526ab10a16a33fe0cf9528b52b8524e012451
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Link memory.c instead of including it.
Change-Id: I2bc461b13332ec5885c33c87828a5fd023f8e730
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/29574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
* Remove dead code
* Add support for types 2504 and 2505
* Print dock info at romstage entry
* Improve dock disconnect for type 2505
* Move defines into dock.h for future ACPI code
* Reduce timeouts according to spec to decrease boot time on error
* Fix no docking detection (reduces boot time by 1 second)
* Configure GPIO LDN before reading GPIOs
* Use Kconfig values instead of fixed defines
* Add documentation
Tested on Lenovo T500 with docking 2504 and 2505.
Change-Id: Ic4510ffadc67da95961cecd51a6d8ed856b3ac99
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/29418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add 20ms adjust timing for edp panel in devicetree.
BUG=b:118011567
TEST=verify panel sequences by ODM.
Change-Id: Iab46f6fc653047a1ec6e8528eefa0999d7019690
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29473
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Add two parameters for panel initialization timing.
> lvds_poseq_varybl_to_blon
> lvds_poseq_blon_to_varybl
2. The BL_PWM is controlled by APU_EDP_BKLTEN_L/APU_DP_VARY_BL/
EDP_BKLTEN_L, so move APU_EDP_BKLTEN_L to early init stage,
and be enabled depends on SKU, thus we can control the delay
time by config APU_DP_VARY_BL.
BUG=b:118011567
TEST=emerge-grunt coreboot.
Change-Id: Ib20c48813b208d697b950b2f02a70a690e483fdb
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
generation
This changes uses drivers/intel/wifi chip for CNVi device to ensure that:
1. Correct device name shows in ACPI name space
2. Correct wake up shows in cat /proc/acpi/wakeup
3. Remove cnvi.asl from soc/intel/icelake
Change-Id: I21d3818ac9e384b0dbaa330d231022bdb8b8a547
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/29507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
GPIOs that use GPI_APIC setting with DEEP can cause an IRQ storm after
S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic
reset over PLTRST to prevent IRQ strom after S3 resume.
For sarien/arcada these are all runtime IRQs only, not wake capable.
Change-Id: Iec3706a3b47b54abbacd06081910f389979c330f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Select the option to disable eSPI when ACPI is enabled so the EC
is unable to assert an SMI when booted into the OS. There is a
kernel driver that implements the same mailbox interface so it
cannot also be used by the SMI handler.
Change-Id: I8bafc749f22aed5595e19e773762ee8b038950b9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
GPIO's that use GPI_APIC setting with DEEP causes an IRQ storm after
S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic
reset over PLTRST to prevent IRQ storm after S3 resume and hence
configuring GPP_D9 and GPP_D10 to use PLTRST.
BUG=b:119202293
TEST=none
Change-Id: I98d71100f28fb9bae05db3fb7d9afcb3f81beb43
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29538
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPP_C11 (FPMCU_INT_L) was set to DEEP, causing problems with S3.
Changed GPP_C11 configuration to use PLTRST instead.
BUG=b:114196791
TEST=Build, flash, boot nocturne, log in to kernel and execute
the following two commands and verify it passes :
echo 0 > /var/lib/power_manager/suspend_to_idle && restart powerd
sudo suspend_stress_test -c 2
Change-Id: I008532fce963c51a435378001440ac72b5ebfffc
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
FSP 2.0.7.1 provides UPD interface to execute IPC command. Configure
PmicPmcIpcCtrl for PMC to program PMIC PCH_PWROK delay from default
100ms to 10ms to improve cold boot and S3 resume performance.
BUG=b:118676361
CQ-DEPEND=CL:*703187
TEST=Verified system_resume_firmware_ec time reduction.
Change-Id: I41b8268c752573d828e31a1d94d3f175aa3cc145
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/29485
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
add the memory parts as ram id 10:
hynix_dimm_H5ANAG6NAFR-UHC
BUG=b:113983573
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: I137259b88f39779768a58959a2dcc565645eee6d
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change allows to redirect coreboot console output to COM2 by
setting appropriate UART index in Console menu in Kconfig.
Change is helpful for users which would like to use COM1 port for
other purposes, because COM1 is the only port with hardware flow
control.
Change-Id: I39f88d7e7794f603775a985afe07fef349172e5f
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/29255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This mainboard is based on mc_apl1. In a first step, it concerns a copy
of mc_apl1 directory with minimum changes. Special adaptations for
mc_apl4 mainboard will follow in separate commits.
Change-Id: I3dfdccc8198f3a23a45d319ede6080803a46f7f6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This mainboard variant requires GPIO adaptations to match the hardware.
Change-Id: I16387358d6c6fa15efd16f7ba7f6b89740477e9d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
RCBA address numbers in comments looks wrong and confusing. Let's fix
them.
This is a cosmetic change since no actual data is added or removed.
Change-Id: I0e521acdac17959586bc0af7d8a2f7182f1e6721
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
See also commit 4ad1446b with Change-Id
I036208a111d009620d8354fa9c97688eb4e872ad ("Fix non-local header treated
as local").
Change-Id: Idea19b52198e6f46b0da6022558a46246a52f2e7
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29501
Reviewed-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ia997c5188aef0c18d871658209c2d5f718ee2a19
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This structure was defined but never used. Let's use it.
Change-Id: I73baf428a7300e64fa486699e82ef62c6a53ea60
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Disable I2C7 because there is no device connected.
Change-Id: Ie9877d40b06f4a849163a873fd308ff03995fcdc
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Enable all PCIe root ports for this mainboard.
Change-Id: I62c7ba5048b4c2288bb502a78b9621edda333f2a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
There is no device on I2C0 which requires a lower clock rate.
Change-Id: Ib9ad4d9026267d2079e95245994d84c163b28dbb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29504
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
All PCIe root ports of this mainboard do not have an associated CLKREQ
signal. Therefore the ports are marked with "CLKREQ_DISABLED".
Change-Id: I59c1132c6d273ccefeb1be6243577e1ae5064ef4
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This mainboard variant requires GPIO adaptations to match the hardware.
Change-Id: I4ba475e7d387f46ed5f41b7a691c7933edbc50c5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change adds a sku_id() function that returns a static value to
differentiate the sarien and arcada boards.
Change-Id: I1fecc675573a6aece7188aae9370733068d45dbf
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29486
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Refer to CL:1043916
BUG=none
BRANCH=none
TEST=none
Change-Id: I3fbbbcac334646f68b8b9fd38fbb529d9e833581
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
generation
This changes uses drivers/intel/wifi chip for CNVi device to ensure that:
1. Correct device name shows in ACPI name space
2. Correct wake up shows in cat /proc/acpi/wakeup
3. Remove cnvi.asl from soc/intel/cannonlake
Change-Id: Ic81de2dce6045ced913766790a40ed19119f5118
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/29399
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Some variants of nami will have a fingerprint MCU.
BUG=b:118503113
BRANCH=Nami
TEST=None (build and boot, but no hw yet)
Change-Id: I446dc09cdf7f84a801723cb403d2de80e0997c65
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/29297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Marvell is the chip company, Marvel makes comic books.
Change-Id: I437ac0d4fc706fbb62a0a74ca74a197dba4499fb
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/29347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
WWAN start-up control requires RESET# assert after FULL_CARD_POWER_OFF#
set to high more than 10 ms, so force RESET#(GPP_D21) to low at
bootblock stage to match the sequence.
BUG=N/A
TEST=Boot up Sarien/Arcada board, check WWAN get detected as USB
devices through lsusb.
Change-Id: I36eb841a2e8f2b36771d20577314a7451fbee133
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/29430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This change removes the function defintions from variant
so that the weak definition in baseboard can be used.
Refer to CL:813944.
BUG=none
BRANCH=master
TEST=Build and boot on DUT
Change-Id: I561414fcc94e3c812bb88730df9b94e332c61781
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update GPP_D9 to fix audio jack can't detect issue.
BUG=b:118393646
BRANCH=master
TEST=Verify audio jack can auto detect.
Change-Id: I87d24ed294c1ddc59bbd6ba9194c76d1f66413f3
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use GPIO_134 as the EC sync interrupt and provide this value
to the embedded controller to be exported to the OS.
BRANCH=none
BUG=crbug:896347, b:118443377
CQ-DEPEND=CL:1298699
TEST=verify sensor events coming in on a reworked board
with companion EC and kernel patches
Change-Id: I41333cabe97bc8b0d59e19d84366f2ea2a59e026
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/29278
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add option for Nanya NT6CL256T32CM-H1 part.
Add comments to indicate total memory size for convenience.
BUG=b:118624505
BRANCH=master
TEST=none
Change-Id: I82200e7b3d0a13295cb38f53ab576697ff8d302b
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Ic08b191ee4dbcc56eb482601aa268394545936ba
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29292
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ib3aafcc586b1631a75f214cfd19706108ad8ca93
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29285
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I0668b73cd3a5bf5220af55c29785220b77eb5259
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29103
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Using a conditional statement to return 0 or 1 depending on a logic
value is unnecessarily complex.
Change-Id: I449ce2b71b72374de5ec4986f9cc9f91a67856ee
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29265
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are some small mistakes in these recently-added mainboards:
- board_info.txt: Lists board socket incorrectly.
- cmos.default: Loglevel was decreased some time ago.
- devicetree.cb: Spelling mistake.
- Kconfig: Mainboard name does not have a hyphen.
Change-Id: I08d9b06e79683acd3994b84647bce401ed6741e2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/29446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Get board id from AUXIN4 and RAM code from AUXIN3.
BUG=b:80501386
BRANCH=none
TEST=AUXIN4 is 0.074v and AUXIN3 is 0.212v on P0.
AUXIN4 is 0.212v and AUXIN3 is 0.212v on P1.
Change-Id: I50533e851d2fae66ae8c5e4e1aa36708d9058e94
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/29062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The Sarien mainboard uses the newly added Wilco EC.
- enable CONFIG_EC_GOOGLE_WILCO
- add the device and host command ranges to the devicetree
- have the mainboard SMI handlers call the EC handlers
- add EC and SuperIO devices to the ACPI DSDT
- call the early init hook for serial setup
Change-Id: Idfc4a4af52a613de910ec313d657167918aa2619
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add a variant of the Sarien board called Arcada. This is currently
very similar to Sarien with differences in PCIe, USB, and GPIO usage.
Change-Id: I432d2ba99558e960d4e775c809cc8bf6aa1a56bf
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29410
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sarien is a new board using Intel Whiskey Lake SOC. It also uses
the newly added Wilco EC, enabled in a separate commit.
Sarien is not a true reference board, it is just one variant of
a very similar design. For that reason it is not considered the
baseboard but rather a standalone variant.
Change-Id: I2e38f617694ed2c2ef746ff8083f2bfd58cbc775
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable the radium touchscreen support
BUG=b:117960394
BRANCH=master
TEST=
1. emerge-nami coreboot chromeos-bootimage
2. boot up on ekko DUT to check touchscreen device by evtest
/dev/input/event3: Raydium Touchscreen
Change-Id: I16167d5d3ce6eac9d64832b52bb1945999a63a90
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29365
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modify flash layout to match ICL-IFWI layout for early SoC PO support
Flash Reg 0: Descriptor [0x0 - 0xFFF]
Flash Reg 1: BIOS [0x400000 - 0xFFFFFF]
Flash Reg 2: IFWI (consist of ME primary & secondary partition and PMC FW)
[0x81000 - 0x3FFFFF]
Flash Reg 8: EC (applicable for Intel RVP with internal EC support)
[0x1000 - 0x80FFF]
Change-Id: I462a384739b5972d9a59569ffdcadba7cdef6a81
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/29316
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The function `acpi_fill_madt()` is identical among all the Lynx Point
boards and sb/intel/bd82x6x, so share a common function between them.
Earlier Intel platforms have similar implementations of this function.
The common implementation might only need minor alterations to support
them.
Tested on an ASRock H81M-HDS and Google Peppy (variant of Slippy). No
issues arose from this patch.
Change-Id: Ife9e3917febf43d8a92cac66b502e2dee8527556
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/29388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The platform.asl file is copied from sb/intel/bd82x6x, and also matches
the contents deleted from each mainboard's platform.asl.
Tested on an ASRock H81M-HDS and a Google Peppy board (variant of
Slippy). No issues arose from this patch.
Change-Id: I539e401ce9af83070f69147526ca3b1c122f042c
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/29386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This patch is based on a8a9f34e9b7b ("sb/intel/i82801{g,j}x:
Automatically generate ACPI PIRQ tables")
Tested on an ASRock H81M-HDS. The generated _PRT object looks correct,
and the system doesn't show any issue when running. The following
assignments occur:
ACPI_PIRQ_GEN: PCI: 00:02.0: pin=0 pirq=0
ACPI_PIRQ_GEN: PCI: 00:03.0: pin=0 pirq=0
ACPI_PIRQ_GEN: PCI: 00:14.0: pin=0 pirq=0
ACPI_PIRQ_GEN: PCI: 00:16.0: pin=0 pirq=0
ACPI_PIRQ_GEN: PCI: 00:1a.0: pin=0 pirq=0
ACPI_PIRQ_GEN: PCI: 00:1b.0: pin=0 pirq=6
ACPI_PIRQ_GEN: PCI: 00:1c.0: pin=0 pirq=0
ACPI_PIRQ_GEN: PCI: 00:1c.1: pin=1 pirq=1
ACPI_PIRQ_GEN: PCI: 00:1c.2: pin=2 pirq=2
ACPI_PIRQ_GEN: PCI: 00:1c.3: pin=3 pirq=3
ACPI_PIRQ_GEN: PCI: 00:1d.0: pin=0 pirq=7
ACPI_PIRQ_GEN: PCI: 00:1f.2: pin=1 pirq=3
ACPI_PIRQ_GEN: PCI: 00:1f.3: pin=2 pirq=2
Also tested on a Google Peppy board. The following assignments occur:
ACPI_PIRQ_GEN: PCI: 00:02.0: pin=0 pirq=0
ACPI_PIRQ_GEN: PCI: 00:03.0: pin=0 pirq=0
ACPI_PIRQ_GEN: PCI: 00:14.0: pin=0 pirq=2
ACPI_PIRQ_GEN: PCI: 00:1b.0: pin=0 pirq=6
ACPI_PIRQ_GEN: PCI: 00:1c.0: pin=0 pirq=0
ACPI_PIRQ_GEN: PCI: 00:1d.0: pin=0 pirq=3
ACPI_PIRQ_GEN: PCI: 00:1f.2: pin=0 pirq=6
ACPI_PIRQ_GEN: PCI: 00:1f.3: pin=1 pirq=2
ACPI_PIRQ_GEN: PCI: 00:1f.6: pin=2 pirq=1
A diff of the _PRT object for the Google Peppy board is below. The code
used in the diff has been modified for clarity, but the semantics remain
the same. To summarise the diff:
* The disabled PCIe root ports are no longer included.
* The LPC controller is no longer included, as it has no interrupt pin.
The pins for the remaining LPC devices are each one less. Perhaps the
original _PRT object was incorrect?
* The SDIO device is no longer included, as it is disabled.
* The Serial IO devices are no longer included, but that is due to a
separate issue I am having with this system (the devices don't show up
under Linux regardless of this patch). In short: their omission is not
a fault of this patch.
--- pre/_PRT
+++ post/_PRT
@@ -1,301 +1,157 @@
Method (_PRT, 0, NotSerialized) // _PRT: PCI Routing Table
{
If (PICM)
{
- Return (Package (0x12)
+ Return (Package (0x09)
{
Package (0x04)
{
0x0002FFFF,
Zero,
Zero,
0x10
},
Package (0x04)
{
0x0003FFFF,
Zero,
Zero,
0x10
},
Package (0x04)
{
0x0014FFFF,
Zero,
Zero,
0x12
},
Package (0x04)
{
0x001BFFFF,
Zero,
Zero,
0x16
},
Package (0x04)
{
0x001CFFFF,
Zero,
Zero,
0x10
},
- Package (0x04)
- {
- 0x001CFFFF,
- One,
- Zero,
- 0x11
- },
-
- Package (0x04)
- {
- 0x001CFFFF,
- 0x02,
- Zero,
- 0x12
- },
-
- Package (0x04)
- {
- 0x001CFFFF,
- 0x03,
- Zero,
- 0x13
- },
-
Package (0x04)
{
0x001DFFFF,
Zero,
Zero,
0x13
},
Package (0x04)
{
0x001FFFFF,
Zero,
Zero,
0x16
},
Package (0x04)
{
0x001FFFFF,
One,
Zero,
0x12
},
Package (0x04)
{
0x001FFFFF,
0x02,
Zero,
0x11
- },
-
- Package (0x04)
- {
- 0x001FFFFF,
- 0x03,
- Zero,
- 0x10
- },
-
- Package (0x04)
- {
- 0x0015FFFF,
- Zero,
- Zero,
- 0x14
- },
-
- Package (0x04)
- {
- 0x0015FFFF,
- One,
- Zero,
- 0x15
- },
-
- Package (0x04)
- {
- 0x0015FFFF,
- 0x02,
- Zero,
- 0x15
- },
-
- Package (0x04)
- {
- 0x0015FFFF,
- 0x03,
- Zero,
- 0x15
- },
-
- Package (0x04)
- {
- 0x0017FFFF,
- Zero,
- Zero,
- 0x17
}
})
}
Else
{
- Return (Package (0x12)
+ Return (Package (0x09)
{
Package (0x04)
{
0x0002FFFF,
Zero,
^LPCB.LNKA,
Zero
},
Package (0x04)
{
0x0003FFFF,
Zero,
^LPCB.LNKA,
Zero
},
Package (0x04)
{
0x0014FFFF,
Zero,
^LPCB.LNKC,
Zero
},
Package (0x04)
{
0x001BFFFF,
Zero,
^LPCB.LNKG,
Zero
},
Package (0x04)
{
0x001CFFFF,
Zero,
^LPCB.LNKA,
Zero
},
- Package (0x04)
- {
- 0x001CFFFF,
- One,
- ^LPCB.LNKB,
- Zero
- },
-
- Package (0x04)
- {
- 0x001CFFFF,
- 0x02,
- ^LPCB.LNKC,
- Zero
- },
-
- Package (0x04)
- {
- 0x001CFFFF,
- 0x03,
- ^LPCB.LNKD,
- Zero
- },
-
Package (0x04)
{
0x001DFFFF,
Zero,
^LPCB.LNKD,
Zero
},
Package (0x04)
{
0x001FFFFF,
Zero,
^LPCB.LNKG,
Zero
},
Package (0x04)
{
0x001FFFFF,
One,
^LPCB.LNKC,
Zero
},
Package (0x04)
{
0x001FFFFF,
0x02,
^LPCB.LNKB,
Zero
- },
-
- Package (0x04)
- {
- 0x001FFFFF,
- 0x03,
- ^LPCB.LNKA,
- Zero
- },
-
- Package (0x04)
- {
- 0x0015FFFF,
- Zero,
- ^LPCB.LNKE,
- Zero
- },
-
- Package (0x04)
- {
- 0x0015FFFF,
- One,
- ^LPCB.LNKF,
- Zero
- },
-
- Package (0x04)
- {
- 0x0015FFFF,
- 0x02,
- ^LPCB.LNKF,
- Zero
- },
-
- Package (0x04)
- {
- 0x0015FFFF,
- 0x03,
- ^LPCB.LNKF,
- Zero
- },
-
- Package (0x04)
- {
- 0x0017FFFF,
- Zero,
- ^LPCB.LNKH,
- Zero
}
})
}
}
Change-Id: Id3f067cbf7c7d649fbbf774648d8ff928cb752a4
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/29381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change the variant name from kalista to karma.
According to the CL:1298319, the baseboard name is kalista
and the board name is karma.
BUG=none
BRANCH=master
TEST=emerge-kalista coreboot chromeos-bootimage
Change-Id: Idea295cc14249721a6dc0fc4e2ef6470d43e16eb
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29314
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Idf10a09745756887a517da4c26db7a90a1bf9543
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Confirm with RK, H9CCNNNBKTMLBR-NTD uses this sdram config.
sdram-lpddr3-hynix-4GB.inc
BUG=b:117967129
BRANCH=master
TEST=None
Change-Id: I98afc33fd2cb61343be0dcdc007add75bee9c2af
Signed-off-by: Loop_Wu <Loop_Wu@asus.com>
Reviewed-on: https://review.coreboot.org/29366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Move soft_reset() to `southbridge/amd/common/` it's only used for
amdfam10 now.
Drop hard_reset() for good.
Change-Id: Ifdc5791160653c5578007f6c1b96015efe2b3e1e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
According to syndra thermal table, PL2 need to check cpu id.
Set up syndra PL2 value.
1. KBL_U PL2 is 25w.
2. KBL_R PL2 is 29w.
Refer to b:116836990#comment10.
BUG=b:116836990
TEST=The thermal team verify OK
Change-Id: I766a886121a089683565608252b4c176c70e88a3
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Unfortunately Stoney has an issue where enabling the IOMMU causes
a 10%-50% decrease in the integrated graphics performance. It is
also disabled by default on other stoney platforms.
BUG=b:118612241
TEST=Verify that IOMMU is disabled.
Change-Id: Ia396c7227cb21461ec8afbdf746721d4fb28083d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/29342
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mainboard is based on mc_apl1. In a first step, it concerns a copy
of mc_apl1 directory with minimum changes. Special adaptations for
mc_apl3 mainboard will follow in separate commits.
Change-Id: I963ec63bccf71296c3fdabfcf9f3009c2febc791
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: I6a9d71e69ed9230b92f0f330875515a5df29fc06
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29312
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Variants of Nami need to accommodate single channel DDR. Will use
GPP_D10 on nami for identification. GPP_D10 will return 1 when device
is using single channel DDR and 0 when using dual channel DDR.
BUG=b:117194353
BRANCH=None
TEST=dmidecode | grep Channel and make sure that the correct number of
channels gets returned.
Change-Id: If86ab2c5404c4e818ce496ea935227ab5e51730a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/29233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Looks like we must do it in the same way as in l520, t420, t420s,
t430s, t520, t530, x201, x220, x230 models. No idea why t430 should be
handled differently.
Change-Id: Ic4851022267caca267b667b4e3c327838e0a0b66
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29031
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Apply commit 12d681b2 (intel/i945 gm45: Use acpi_s3_resume_allowed())
also to the Lenovo T400.
See also commit 42ae0bae with Change-Id
I4e1e0ccf2abbe175c0e5ddcbb6ee7bf6afb1ae88 (mb/lenovo/x200: Use
acpi_s3_resume_allowed())
Change-Id: I9d4ac711375977a979a8b3e5606e2197847e88de
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Move the usage instructions from their ad-hoc place in Kconfig.name to
the Documentation directory, and expand them a bit.
Change-Id: Id6c7bbca40a21ecba00cab736af2f2662a985106
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
|
|
Linking should allow to link depending on possible future variants.
E.g. in Makefile.inc romstage-$(CONFIG_'VARIANT0') += gpio_variant0.c
etc.
This commit follows up on commit 7dee9745 with Change-Id
I88b5ef8e12ac606751952a493f626e1b146e98f7 ("mb/lenovo/x201: Link gpio
map instead of including a header").
Change-Id: Ibdb96deafbe422bf50fd2e1fc56a57ae53ccd5a0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29286
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
IGD display handling was rewritten with commit dd2bc3f8 with Change-Id
I556769e5e28b83e7465e3db689e26c8c0ab44757 ("igd.asl rewrite"). These
comments were removed as well (with some accidentally left behind).
Let's remove them and those who were introduced later with new ports.
Change-Id: I8d3e12d0c3b03b0de38e65f36b94ed706fbf893c
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29271
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These ifdefs are the remains from the following commits:
* fa1d688a with Change-Id I9909a5b2bdb4b59219db6304fa4332802fe0301c
("sandy/ivy native: dedup romstage.c main()")
* 7dee9745 with Change-Id I88b5ef8e12ac606751952a493f626e1b146e98f7
("mb/lenovo/x201: Link gpio map instead of including a header")
Change-Id: If83189688151f531a05780a87db3409cbacfbeff
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Clone entirely from mainboard/intel/cannonlake_rvp
commit id: af89f49b83260a04dece84b34e97560fb85d29ae
List of changes on top off initial cannonlake_rvp clone
1. Rename "Cannonlake" with "Icelake".
2. Replace "cannonlake_rvp" with "icelake_rvp".
3. Rename "cnl" with "icl".
4. Remove unwanted SPD file, will add correct SPD with mainboard
patches.
5. Remove NHLT related implementation.
6. Remove FSP configs, will add once FSP headers are available.
7. Removed smihandler.c, will add later if needed.
Change-Id: I875972d1fb2f630bf5eb29bd955c484e7f9aa415
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/29164
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In function write_pirq_routing_table(), the function name is used in a print
string. Use __func__ instead.
BUG=b:117642170
TEST=Build grunt.
Change-Id: Ibf8673c5b2cda1105aae1edb46f6589d55208c50
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Add a new variant of fizz for the kalista board.
Key differences from baseboard include:
- GPIO changes
- devicetree.cb changes
BUG=b:117066935
BRANCH=master
TEST=Build (as initial setup)
Change-Id: I808c5e0883049575cbedd181c249a78a833fa96a
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29205
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables override device tree for Fizz to allow variants to
provide their own overrides and also moves I2C5 realtek node to
fizz/overridetree.cb since it doesn't apply to some variants being
added for Fizz.
Change-Id: Ia1a069fc539b51a22882ef94b55baf5bf7cd302f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
Get recovery mode switch from EC and pass it to payload.
BUG=b:80501386
BRANCH=none
Test: Boots correctly on Kukui.
Change-Id: Ib92afca885e5a97ec4646f55f2279ef56a61af5a
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/29190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Liara auto restart issue is caused by memory access error and consequent
kernel panic. To solve this issue, revert the CL:1243666 (Disable
NbP-state on Liara) and use 2T mode instead.
BUG=b:116082728
TEST=verify the 2T mode is enabled/boot into ChromeOS and no auto restart/run
memtester passed 10 cycle.
Change-Id: I3a96276d88ffb70530d72b15c07b59a01cc6209a
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
1. Update PSV values for cpu and sensers.
2. Change PL1 min value from 3w to 4.5w.
3. Change TSR2 TRT source from charger to CPU.
Refer to 112448519#comment31.
BUG=b:112448519
TEST=Build coreboot for Octopus board
Change-Id: I7c7df0f54374fdaa4cf57d5c255d841d7db38cfc
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This change uses CRFP ACPI name for FP device since user space
utilities expect this name for triggering different actions.
BUG=b:112974410
BRANCH=nocturne
Change-Id: I63309227c916b43917e529c223cf738fc3baa209
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29231
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On rammus, set GPIO GPP_C22 to 1 for touchscreen power on.
And add touchscreen device "PNP0C50" to I2C0.
According to touchscreen spec, device power on initialization takes
105 ms, so set "generic.enable_delay_ms" to 120.
We found there is i2c error log pop up when we set delay
time to be 110ms or 105ms. If we set delay time to be
120ms. System will not pop up i2c error log.
BUG=b:115944726
BRANCH=master
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure touchscreen works.
Change-Id: Ibce552d04991e85c99ae3a0a92455fc747d9fced
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change uses DIMM_INFO_PART_NUMBER_SIZE to decide the size of
part_num_store that holds the number of DRAM part. It ensures that
host advertises the supported size to read part number from the EC.
BUG=b:115697578
Change-Id: I8439a301fc037b0acdc8b1226ad04d2f363838ef
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Jett Rink <jettrink@chromium.org>
|
|
Before entering the OS, the AP relies on the smi handler to shutdown the
system when the lid closes. Without the smi_events setting, the AP will
not receive the smi handler. As a result, the AP won't shutdown and will
always keep in S0.
This problem is caused by the https://review.coreboot.org/c/coreboot/+/28983
and this patch adds the smi_events back to support the smi handler for
the lid close.
BRANCH=master
BUG=b:115572596
TEST=test_that -b ${BOARD} ${IP} firmware_ECLidShutdown
Change-Id: Id82311a8ccd109f9c26516f59a45bdf34da98529
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/29191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Change-Id: I6c77f4289b46646872731ef9c20dc115f0cf876d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The file soc/amd/stoneyridge/acpi/smbus.asl has 0 bytes (no content). Remove
the include of this file.
BUG=b:117814641
TEST=Build grunt and gardenia.
Change-Id: I0c48167195a9708afc255490bb1996b6dfc7bdfb
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29178
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change uses the newly added macros for configuring the same GPI
pad(GPIO_135) for IRQ (normal interrupt operations) and
wake (interrupt for waking from S3/S0ix) for the trackpad device. The
other pad GPIO_142 is now configured as not connected.
BUG=b:117553222
TEST=Verified that yorp and bobba wake from S3 and S0ix using
trackpad.
Change-Id: I2b704f1be493141629c647b79723b0025b0f7dd6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29189
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change link frequency of IMX319 from 360Mhz to 482.4 Mhz to match the
changes from kernel driver. IMX319 has two PLLs and it can be configured
either single or dual. Previous driver implemente dual PLL mode, however
image sensor vendor prefer single PLL mode and calculate the pixel rate
became easier. So the kernel driver changed to use single pll, coreboot
change will match that.
Bug=b:116082248
Change-Id: Iac9a72253e0529bf2c0785fb701b7bc251bcbab5
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28736
Reviewed-by: Tomasz Figa <tfiga@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is a cosmetic one. It just removes some board names from comments
since these functions sometimes are very similar, so no need to add
extra difference between them.
Change-Id: I26b9296b402d98bcf048580da51da7bbb0c237e4
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
We didn't have a hard_reset() implementation for these boards. So
select the board_reset() stub for them.
Change-Id: I77651e3844632fb1a347008c96e53d23cc5a2646
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29170
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
And here comes the mess...
This just renames do_hard_reset() to do_board_reset() and keeps current
behaviour. As these are never called from chipset or board code but only
from common code, it's likely that their implementations are untested
and not what we actually want. Also note, that sometimes implementations
for rom- and ramstage differ considerably.
Change-Id: Icdf55ed1a0e0294933f61749a37da2ced01da61c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29058
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SOUTHBRIDGE_INTEL_COMMON_RESET for all Intel platforms that used to
perform a "system reset" in their hard_reset() implementation. Replace
all duplicate CF9 reset implementations for these platforms.
Change-Id: I8e359b0c4d5a1060edd0940d24c2f78dfed8a590
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Id07e1c7fbd35393ffafda53fc7a15ec0e157d075
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: I6182da172ae2f4107a9b5d8190e4b3b10ed2f0b9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This change udpates FMAP to wrap MRC training data in RW_PRESERVE
section so that we don't lose the data when performing full firmware
updates on octopus.
BUG=b:117882029
TEST=Verified that chromeos-firmwareupdate doing full firmware update
preserves training data on octopus.
Change-Id: I5adb9bfa926327057b003360150685a8b4778c8c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Move current NHLT configuration implementation to baseboard so that
variants can leverage it or provide their own configuration.
BUG=b:117066935
BRANCH=Fizz
TEST=emerge-fizz coreboot
Change-Id: I30d93babb6fc09e8642b3740f1f7638fa33f0ade
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add support for ChromeOS GPIO ACPI table information by providing weak
implementation from the baseboard.
BUG=b:117066935
BRANCH=Fizz
TEST=emerge-fizz coreboot
Change-Id: I2fa52c005cacdbcc322d107a3ac92d22df3f3697
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Provide API for gpio table functionality. Default weak
implementations are provided from the baseboard.
BUG=b:117066935
BRANCH=Fizz
TEST=emerge-fizz coreboot
Change-Id: Iaafa8d6932bc0a37826175b15816f1b9a4f4c314
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In order to be able to share code across different fizz variants,
provide the concept of baseboard and variants. New directory layout:
variants/baseboard - code
variants/baseboard/include/baseboard - headers
variants/fizz - code
variants/fizz/include/variant - headers
New boards would then add themselves under their board name within
"variants" directory.
This is purely an organizational change.
BUG=b:117066935
BRANCH=Fizz
TEST=emerge-fizz coreboot
CQ-DEPEND=CL:1273514
Change-Id: I28cc41681e7af88ddeba2e847dc0a4686606feb2
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
I didn't change the offsets of all the other regions because I didn't
want to cause all dogfood devices to lose their corp enrollment.
BUG=b:117797131, b:117798830
BRANCH=none
TEST=Ran autotest and made sure the tests were skipped
/tmp/test_that_results_2OZ90v/results-1-firmware_CorruptRecoveryCache [ PASSED ]
/tmp/test_that_results_2OZ90v/results-1-firmware_CorruptRecoveryCache TEST_NA: No RECOVERY_MRC_CACHE was found on DUT.
/tmp/test_that_results_2OZ90v/results-1-firmware_CorruptRecoveryCache/firmware_CorruptRecoveryCache.normal [ PASSED ]
/tmp/test_that_results_2OZ90v/results-1-firmware_CorruptRecoveryCache/firmware_CorruptRecoveryCache.normal TEST_NA: No RECOVERY_MRC_CACHE was found on DUT.
Change-Id: I5cdbf4139dde80fe6e9d0045139a97841b03bc42
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/29171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
this patch adds following changes
- Select config to initialize codecs in common HDA driver.
- Add audio verb table for coffee lake RVP11 & RVP8.
BUG: None
TEST: boot to yocto linux and windows os on CFL RVP11 & RVP8. verified audio
playback and record functionality over anolog audio jack & HDMI display.
Change-Id: I567e317c0e9ac9f91e159866c7f896e4c101712b
Signed-off-by: praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/29067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Ib359e4039f87bb87faac040f24f70cc0988c0ea8
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29107
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|