| Age | Commit message (Collapse) | Author |
|---|
|
Enable acoustic noise mitgation for volteer platforms.
BUG=b:153015585
BRANCH=none
TEST= Measure the change in noise level by changing the values
in devicetree.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: I69a6453091bf607d3c5847c99bc077e6b7dbc639
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45053
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the two load line slope settings for the SVID3 telemetry.
AGESA sends these values to the SMU, which accepts them as units
of current. Proper calibration is determined by the AMD SDLE tool
and the Stardust test.
VDD Slope: 62852 -> 62641
SOC Slope: 28022 -> 28333
BUG=b:170531252
BRANCH=zork
TEST=1. emerge-zork coreboot
2. pass AMD SDLE/Stardust test
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: Id831907aa47be27fef2e33bb884a1118ffec14a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The disconnect voltage needs to be adjusted up because the HS DC voltage
level is 0xF.
BUG=b:170879690
TEST=Servo_v4 USB hub functions
BRANCH=zork
Change-Id: If8662015a45c57e457b4593e55af888084842f58
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
RW_LEGACY region needs to be 1 MiB to accommodate any alternate
firmware. Hence update the flash ROM layout as below:
* Grab ~512 KiB from each FW_MAIN_A/B regions and allocate them to
RW_LEGACY region so that it grows to 1 MiB.
* Remove VBLOCK_DEV region which is not used.
* Re-size the ELOG region to 4 KiB since that is the maximum size of the
ELOG mirror buffer.
* Resize RW_NVRAM, VBLOCK_A/B regions to 8 KiB since no more than that
size is used in those regions.
* Resize SHARED_DATA region to 4 KiB since no more than that size is
used in that region.
* Based on the resizing, allocate each FW_MAIN_A/B regions with 72 KiB.
BUG=b:167943992, b:167498108
TEST=Build and boot to OS in Drawlat. Ensure that the firmware test
setup and flash map test are successful. Ensure that the event logs are
synced properly between reboots. Ensure that the suspend/resume sequence
is working fine. Ensure that the ChromeOS firmware update completes
successfully for the boot image with updated flash map and the system
boots fine after the update.
Change-Id: I53ada5ac3bd73bea50f4dd4dd352556f1eda7838
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46569
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To support mipi WFC.
1. enable DRIVERS_INTEL_MIPI_CAMERA/SOC_INTEL_COMMON_BLOCK_IPU
2. add IPU/VCM/NVM/CAM1 in devicetree
BUG=b:163879470, b:171258890, b:170936728, b:167938257
TEST=Build and boot to OS. Capture frames using camera app.
Change-Id: I96f2ef682dff851d7788c2b612765a92228ddf75
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44939
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Andy Yeh <andy.yeh@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable caching of memory training data for recovery as well as normal
mode because memory training is taking too long in recovery as well.
This required creating a space in the fmap for RECOVERY_MRC_CACHE.
BUG=b:150502246
BRANCH=None
TEST=Run power_state:rec twice on lazor. Ensure that on first boot,
memory training occurs and on second boot, memory training is
skipped.
Change-Id: Id9059a8edd7527b0fe6cdc0447920d5ecbdf296e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46651
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the metaknight variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:169813211
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_METAKNIGHT
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Change-Id: Ia2e473eb1d0a2c819b874e497de0823fca75645a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add the Chrome OS specific GPIOs (WP, EC, H1, ...) GPIOs.
BUG=None
TEST=emerge-asurada coreboot; # also boots into emmc
BRANCH=None
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Change-Id: Ieeeee88a09ae4c3af15e2ae93a29684d30dde493
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46386
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure and initialize EC and TPM on Asurada.
BUG=none
TEST=boot asurada
Change-Id: I0f169407d1726899fd0c42e144d907024f036c6a
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46385
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The 0x30 register is eventually controlled by coreboot's
pnp_enable_resources() based on the on/off setting. Other
register settings were grouped with their respective "virtual"
LDN, where possible.
Note, this temporarily breaks LDN 8 settings, as coreboot will
ignore configuration for disabled devices.
Change-Id: I8585dd08eed407ab12258f2accaa63dab294e7d8
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The `io` statement will prepare a 16-bit write, hence use `irq` for
miscellaneous 8-bit registers and fix actual `io` settings (i.e. merge
0x61 writes into 0x60). Note, using `irq` is still just a hack as these
are neither I/O nor IRQs, but it's common practice in coreboot.
Change-Id: I2e1c2286be726d126598cc4a97bb15a57faef42f
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The mainboard has a PS/2 port, so enable the keyboard controller in the
devicetree.
The PS/2 keyboard now works in SeaBIOS payload, but not in GNU/Linux,
probably as ACPI code still needs to be added.
Change-Id: I7846633bc1a3bdf6bffae628e0542bb8fb684804
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Enhance USB 2.0 SI by increasing the level of "HS DC Voltage Level"
and "Disconnect Threshold Adjustment".
COMPDISTUNE0: 0x3->0x7
TXVREFTUNE0: 0x6->0xf
BUG=b:162614573
BRANCH=zork
TEST=1. emerge-zork coreboot
2. check U2 registers are set correctly
3. test with servo v4 type-c, it's working expectedly.
4. U2 SI pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I278cc0aaddbc9fce595bf57ca69ee8abfc9f5659
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46537
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct the two load line slope settings for the SVID3 telemetry.
AGESA sends these values to the SMU, which accepts them as units
of current. Proper calibration is determined by the AMD SDLE tool
and the Stardust test.
BUG=b:168265881
BRANCH=zork
TEST=emerge-zork coreboot
Change-Id: Id6c4f1a92d7f2ad293df7b63694e9665b85f8018
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46472
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Early JSL silicon hang while booting Linux with ISST enabled. The
malfunctioning silicon revisions have been used only for development
purposes and have been phased out. Thus, drop the ISST workaround.
Change-Id: Ic335c0bf03a5b07130f79c24107a1b1b0ae75611
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Currently, the serial console does not work.
With the serial port enabled in the vendor firmware, `superiotool` outputs
the global control register values below.
Found Nuvoton NCT6779D (id=0xc562) at 0x2e
Register dump:
idx 10 11 13 14 1a 1b 1c 1d 20 21 22 24 25 26 27 28 2a 2b 2c 2f
val ff ff ff ff 3a 28 00 10 c5 62 df 04 00 00 10 00 48 20 00 01
def ff ff 00 00 30 70 10 00 c5 62 ff 04 00 MM 00 00 c0 00 01 MM
UART A needs to be enabled in CR 0x2a by clearing bit 7. Do this by
selecting the Super I/O Kconfig symbol `SUPERIO_NUVOTON_COMMON_COM_A`.
This changes the default value 0xc0 to 0x40.
Note, due configuring the system as legacy free with
`HUDSON_LEGACY_FREE=y`, AGESA in romstage disables the LPC controller in
`FchInitResetLpcProgram()`.
coreboot-4.12-3417-g192b9576fe Tue Oct 20 09:15:53 UTC 2020 romstage starting (log level: 7)...
APIC 00: CPU Family_Model = 00610f31
APIC 00: ** Enter AmdInitReset [00020007]
Fch OEM config in INIT RESET
`AmdInitReset() returned AGESA_SUCCESS` is not transmitted anymore. Only
when coreboot enables the LPC controller again in ramstage, serial output
continues.
PCI: 00:14.4 bridge ctrl <- 0013
PCI: 00:14.4 cmd <- 00
PCI: 00:14.5 cmd <- 02
PCI: 00:15.0 bridge ctrl <- 0013
PCI: 00:15.0 cmd <- 00
PCI: 00:15.1 bridge ctrl <- 0013
[…]
done.
BS: BS_DEV_ENABLE run times (exec / console): 0 / 30 ms
Initializing devices...
CPU_CLUSTER: 0 init
[…]
Note, due to incorrect Super I/O configuration in the devicetree, the boot
hangs in `PCI: 00:14.3 init` when doing `outb(0, DMA1_RESET_REG)`. This
will be fixed in follow-up commits.
TEST=Receive (some) coreboot log messages over the serial console.
Change-Id: I0aa367316f274ed0dd5964ba5ed045b9aeaccf8d
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Following commit f50ea988b a couple of symbols are gone, so follow up
that change for this board as well.
Change-Id: I09fd3a107447eb45bb46b7f0f821377943f140b2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46621
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Get rid of legacy pad macros by replacing them with their newer
equivalents.
TEST: TIMELESS-built board images match
Change-Id: I078f9bb3c78f642afc6dcfd64d77be823a4485c2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update PL1 max and min power values
BUG=None
BRANCH=None
TEST=build and verify on dralat system
Change-Id: I75d47fa721576564f71fbd5d5fd2e820fc3f1925
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Configure board specific DPTF parameters for terrador and todor
BUG=b:171019363,b:170699797
BRANCH=volteer
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I19935ca98ec7a078869e73d65ea471df70f37121
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add generic LPDDR4x SPD support for the following three memory
parts:
• K4U6E3S4AA-MGCR
• H9HCNNNBKMMLXR-NEE
• MT53E512M32D2NP-046 WT:F
BUG=b:170264065
TEST=none
Change-Id: Ie3163763a0ce291f27c43181d35c070c218b461d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add devicetree and device ID for P-sensor
BUG=b:161217096
BRANCH=NONE
TEST=We can get the data from P-sensor if touch the SAR antenna.
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: I70f303995b106cca9758b36ebcde112ebcc90950
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update devicetree of boten that enable stylus
BUG=b:160752604
BRANCH=NONE
TEST=build bios and verify function for boten
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: Ifbcac18fcf758f3d870a6af0d1b03e34369414c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
I often find myself having to increase the CBFS size so that TianoCore
fits. Raise the default CBFS size to 2 MiB to alleviate this issue.
Change-Id: I871bb95dee55cc5bad68bb6e71f89ddfa4823497
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46488
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds another X11 series board, the X11SSH-F, which is similiar to
X11SSH-TF but differs in PCIe interfaces/devices, ethernet interfaces.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: I92c32bff861f0b5697aea52ff282fae76b3b78ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Ied350570a695cca1424a6562e41120bcaf467797
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44568
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This Chili mainboard is used in an all-in-one PC.
For more information see
https://www.secunet.com/fileadmin/user_upload/_temp_/importexport/Print/Factsheets/englisch/SINA_Workstation_H_Client_V_Factsheet_EN_Web.pdf
Change-Id: Ic7a5dccbb0d5b7bceb154fb050cf991254475f7b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39995
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Thomas Heijligen <src@posteo.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Chili base board is a ruggedized laptop with additional industrial
interfaces. So far, only booting and basic interfaces (USB, UART,
Video) are working with the original model, the "base" variant.
No further development is planned for this variant, as our primary
target was another one that will be added in a follow-up.
Change-Id: I1d3508b615ec877edc8db756e9ad38132b37219c
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
BUG=b:170703029
BRANCH=octopus
TEST=emerge-octopus coreboot
Signed-off-by: James Chao <james_chao@asus.corp-partner.google.com>
Change-Id: I2bf642963283b8a31a3bd9504c40541ca2f64b34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
There's no need to have multiple Kconfig symbols which do the same
thing. Introduce `SUPERIO_NUVOTON_COMMON_COM_A` and update boards to use
the new symbol. To preserve alphabetical order in mainboard Kconfig,
place the new symbol above the Super I/O symbol (instead of below).
Change-Id: Ic0a30b3177a1a535261525638be301ae07c59c14
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46522
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
No recent Chromebooks have used I2C for TPM communication, and as a
result, a bug has crept in. The ability to extract Cr50 firmware string
is only supported via SPI, yet code in mainboard and vendorcode attempt
to do so unconditionally.
This CL makes it such that the code also compiles for future designs
using I2C. (Whether we want to enhance the I2C protocol to be able to
provide the version string, and then implement the support is a separate
question.)
This effort is prompted by the desire to use reworked Volteer EVT
devices for validating the new Ti50/Dauntless TPM. Dauntless will
primarily be using I2C in upcoming designs.
BRANCH=volteer
TEST=util/abuild/abuild -t GOOGLE_VOLTEER -c max -x
Change-Id: Ida1d732e486b19bdff6d95062a3ac1a7c4b58b45
Signed-off-by: jbk@chromium.org
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
This reverts commit c4a5acdabc28778b49a1c088b0736bac83e2ab51.
Reason for revert: Dalboz is missing pull-up on cmd line, so 400khz is not possible.
TEST=Boot Dalboz
BUG=b:159823235, b:169940175
BRANCH=zork
Change-Id: I89653bfeefa522c17ee2d736215bc22aa445871c
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The camera sensor component chosen for UFC and WFC have an address
conflict. Resolve it by enabling GPIO based I2C Multiplexer. Also
configure the GPIO that is used as select line.
BUG=b:169444894
TEST=Build and boot waddledee to OS. Ensure that the ACPI identifiers
are added for I2C devices multiplexed using I2C MUX under the
appropriate scope.
Change-Id: I9b09e063b4377587019ade9e6e194f4aadcdd312
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable the USB4 retimer driver with GPP_H10 as the power control.
Change-Id: I166bc477f94c159bb411620a6bf77b5d1f194fb2
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
To support camera second source GC5035 for kodama, add world facing
camera id as part of the sku id, which is determined by the data in
camera EEPROM. For models other than kodama, the camera id is always 0
and hence the sku id is unchanged.
BUG=b:144820097
TEST=emerge-kukui coreboot
TEST=Correct WFC id detected for kodama with GC5035 camera
BRANCH=kukui
Change-Id: I63a2b952b8c35c0ead8200d7c926e8d90a9f3fb8
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45811
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new memory.c to support DDR4 memory types.
BUG=b:170604353
TEST=emerge-volteer coreboot chromeos-bootimage
Change-Id: If96b0bda0ce95766f0957c37aa7cbecefc9c03e0
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
There's no need to use static functions to fill these settings in. Also,
add missing include for <stdint.h> and initialize `mem_cfg` in one line.
Change-Id: I82b0997846d4ec40cf9b1a8ebfb1e881b194e078
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46252
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update dptc setting:
Stapm_time_constant 1400
BUG=b:170696020
BRANCH=zork
TEST=emerge coreboot and check "Stapm_time_constant"
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I61d9e00a9d098ad9699b8cf89e70d11de2b95ffd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
The passive clause is constructed with the past participle, which is
*defined* in this case. Fix all occurrences in AMD vendor code with the
command below.
git grep -l "is define at" src/mainboard/ | xargs sed -i 's/is define at/is defined at/'
Change-Id: I5aa0e6e064410b305aa5f2775271f6a8988da64b
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46066
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With a tabulator length of eight spaces, the alignment is the same, but
the other macro definitions are using a space, so do the same for
consistency, better alignment in diff views.
git grep -l -P 'define\tBLD' | xargs sed -i 's,define\tBLD,define BLD,g'
Change-Id: Ib71057c84dc897028cb0ceac29952e67bc541d2e
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch adds some Kconfig hints to make it clearer that the
USE_QC_BLOBS option is required for SC7180 boards and guide the user in
the right direction through menuconfig. Also add those little arrows to
the Trogdor board options that are there on most other boards.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I973cae8026a229408a1a1817c4808b0266387ea7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philip Chen <philipchen@google.com>
|
|
This configuration option shares a name with the FSP UPD, but
is enumerated differently. Change its name to minimise confusion
about the options.
Change-Id: Id74f043ecd549bde4501320bff1dc080bde64057
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Berknip has SSD/eMMC SKU, we should turn off eMMC if storage is NVMe SSD.
BUG=b:170592992
BRANCH=zork
TEST=1. emerge-zork coreboot
2. Check eMMC is enabled or disabled based on the eMMC bit in
FW_CONFIG.
Change-Id: I7aeabc98fc16bc2837c8dcdc40c3c6a80898cdc9
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
TEST=Build and test booting ADL RVP form NVMe and Optane
localhost ~ # lspci -d :f1a6
Show all the NVMe devices and be really verbose
localhost ~ # lspci -vvvd :f1a6
Print PCIe lane capabilities and configurations for all the NVMe devices.
Change-Id: I0a04b23b17df574d4fa3bae233ca40cd3b104201
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
A regular M.2 NVMe SSD shows up on RP9 and runs at x4 width.
Optane memory module shows up as 2 NVMe devices in x2 config:
- NVMe storage device uses RP9
- NVMe Optane memory uses RP11
Note: These two devices are sharing CLK PINs because of same M.2 slot.
TEST=Build and boot ADL RVP board using Intel Optane card.
Change-Id: Ia21d7d2fd07c4fb32291af7bb5a2e41e40316278
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Make PCI ClkReq-to-ClkSrc mapping correct to fix SSD detection issue
on ADL RVP.
TEST=Able to detect WD SSD card over PCH SSD RP9.
Change-Id: I7e26429281f8d3b9edae0f266a5868118369be3f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch programs GPIO for PCH SSD Power Enable (GPP_D16) and Port
Detect (GPP_A12) as per schematics.
TEST=Able to build and boot ADL RVP.
Change-Id: I015e46bdf25437c6b196deb3e610bc1b58726070
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
HybridStorageMode FSP UPD needs to be set only for optane storage.
Enabling HybridStorageMode causes some extra delay in FspSiliconInit due
to HECI command and hence is avoided for NVMe and SATA scenerios. This
change disables "HybridStorageMode" for volteer baseboard. For boards
using optane HybridStorage needs to be enabled from overwrite devicetree.
We are enabling HybridStorage for volteer and volteer2 as those plaforms
have SKU's with optane storage.
BUG=b:158573805
TEST=Build and boot non optane device and confirm that FspSiliconInit
time is reduced. This saves ~100ms.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: I54fc78e3f888d4f2a02ba0ad6b9aef33eb872a9c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add required ASL files into dsdt.asl
TEST=Dump and disassemble DSDT and verify all ACPI devices are present.
Change-Id: I70829e2bdb12fad20627d9aea47e745d9095f07a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
List of changes:
1. Add devicetree.cb config parameters related to FSP-S UPD
2. Configure GPIO as per ADL-P RVP
3. Add files required for ramstage(ec.c, mainboard.c)
4. Add smihandler.c for SMM
5. Add devicetree changes as below
- USB OC PIN programing
- GPE configuration
- SATA port mapping
- LPSS configuration
- Audio configuration
- IA common SoC configuration
- EDP configuration
- TCSS USB configuration
- Enable S0ix
TEST=Able to boot ADL-P RVP without Chrome EC (using on-board EC) with
UART log over legacy UART0 port as 0x3f8 with NVME at RP9 reach till
depthcharge payload.
Change-Id: I120885956c88babfa09d24ce1079d49306919b8a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
These settings are not necessary for DDR4 and can be dropped.
Change-Id: I1946be239f0c90db995a60570474039cef45cfa9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Add tcc, critical, passive policy, and pl values from thermal team.
BUG=b:169215576
TEST=build and verify by thermal tool
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I4f61eaa7eab2b86b04ff0541886621afb3082b1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Enables Pcie M.2 support for WWAN and disable M.2 USB.
RP4 is already on and PcieRpEnable[3] is enabled. Clock source 2 is already
configured. Added missing gpio configuration.
BUG=none
TEST=Boot to OS, check WWAN functionality
Change-Id: Ie9b7915062b2ef65d881d478e64322c0b8765614
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45828
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add generic wifi ACPI entry for wake on lan event.
Change configuration of GPIO 2/WIFI_PCIE_WAKE_ODL to SCI.
BUG=b:162605108
TEST=$ iw phy phy0 wowlan enable disconnect
$ cat /proc/acpi/wakeup | grep WF
WF00 S3 *enabled pci:0000:01:00.0
$ powerd_dbus_suspend
Reboot wifi router, DUT wakes up
BRANCH=zork
Change-Id: Idbeb2cfbc4995b8382ffc26cbe7b53764fc9252d
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45745
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable ALS ACPI devices for dooly.
BUG=b:168426118
BRANCH=puff
TEST=Ensure that ALS devices are enabled in ACPI tables.
Change-Id: Idd44d6ae1e7b62939fdfc3a0ab01924d2c1714aa
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Change-Id: I1e0489ec6730760f74102cdd00e4aaa66975d69a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Make output AML file name uniform.
Change-Id: Ic6cac4748a6159c695888b2737ada677d91f4262
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I5a5f4e7067948c5cc7a715a08f7a5a3e9b391191
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Create the elemi variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:170604353
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_ELEMI
Change-Id: I6013b6d8b28610a79f5ec49d373b2897799bffef
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Change-Id: I71ee54116ade4d6826dffc31ee879a70d3fc967f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This change switches all mainboard devices to use drivers/wifi/generic
instead of drivers/intel/wifi chip driver for Intel WiFi
devices. There is no need for two separate chip drivers in coreboot to
handle Intel and non-Intel WiFi devices since the differences can be
handled at runtime using the PCI vendor ID. This also allows mainboard
to easily multi-source WiFi chips and still use the same firmware
image without having to distinguish between the chip drivers.
BUG=b:169802515
BRANCH=zork
Change-Id: Ieac603a970cb2c9bf835021d1fb0fd07fd535280
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Pictures on the internet show that the Asrock H110M-DVS (Kconfig.name)
only has two DIMM slots. Since the vendor's website advertises support
for dual channel memory, drop the SPD addresses for the second slot of
each channel. The result is the same as several other two-slot boards.
Change-Id: I4b62e9196bfa3a688016399d7e025ca995f3c12c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The DQ and DQS byte maps do not apply to DDR4 configurations, and the
RCOMP resistor and target values are not correct for SKL-S (or KBL-S).
Drop the byte maps and use RCOMP values for the correct platform type.
RCOMP resistor values for all non-socketed platforms are listed in the
Platform Design Guide, and also appear in schematics. For SKL-S, the
RCOMP resistors are on the CPU and their values have been confirmed
by measuring them on an i5-6400, and match the PDG values for SKL-H.
RCOMP target values can be guessed from Intel Document #573387 and some
of them are also present in datasheet volume 1, under DC specifications.
Change-Id: I699d46b9b516be8946367e6d9b24883ae1e78d03
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Update Slot Designation strings and add SSD0_M2_Boot_Drive for config A.
TEST="dmidecode -t 9" to verify the results are expected.
Signed-off-by: Jingle Hsu <jingle_hsu@wiwynn.com>
Change-Id: I3fc03a14ff7dc43d6ddf5aa36710c99dbc648afa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
1. Add speaker amplifier ALC1015
2. Enable dmic+ssp registers for speaker and camera DMIC
3. Correct I2C#2 to LVDS, I2C#3 to Touchscreen
BUG=b:170273526
BRANCH=puff
TEST=Build and check DUT function status
Change-Id: I5f6f19b40c6fcce8dca9b010ae97ea6e3eeb1473
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46289
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove unused device in Dooly
no SD card reader
no built-in LAN
BUG=b:170273526
BRANCH=puff
TEST=Build and check DUT function status
Change-Id: I8ab1e156031bfb4d5ea30048d8a10400f2a49411
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Dooly has USBA*2 and USBC*2
BUG=b:170273526
BRANCH=puff
TEST=Build and check DUT function status
Change-Id: Icb66a8d5382ca9664e7f0b3660f446aeb3cf1dd3
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46126
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Override unused device
SD card reader, built-in LAN
ALC1015 speaker amplifier SPK_AMP_ON
Update touchscreen/lvds gpio pin
BUG=b:170273526
BRANCH=puff
TEST=Build and check DUT function status
Change-Id: Ife14adf59609870abe9f4ba1eabe2573cb6e92dd
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Change-Id: I6f4d0bf9adc1cce4942a16675a072ffea00bd2e0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
0x5 to 0x2
DSDT revision 2 is used for ACPI v2 and greater.
Change-Id: Ia019358be6574db1b2b06a8a7d52ae996cf45571
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Refer to commit d7b88dc (mb/google/x86-boards: Get rid of power button
device in coreboot)
This change gets rid of the generic hardware power button from all
intel mainboards and relies completely on the fixed hardware power
button.
Change-Id: I8f9d73048041d42d809750fdb52092f40ab8f11f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The DQ and DQS byte maps do not apply to DDR4 configurations, thus
simply drop them.
Also drop ECT, as it's already initialized to zero and can't be used on
DDR4 anyway.
Further, trim down all the meaningless and/or wrong comments.
Change-Id: I32f1b7bb46eaaf0f0ecad1df310f5de988f64c85
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46249
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop the disabled SPD indices from memcfg, since they're already
initialized to 0.
Change-Id: I6d88bdac17222c2c5c35439517fe0bea46744b2b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Drop USE_LEGACY_8254_TIMER, since it's not required anymore for
booting grub, despite the comment. The issue was resolved upstream
five years ago: http://git.savannah.gnu.org/cgit/grub.git/commit/?id=d43a5ee65143f384357fbfdcace4258e3537c214
Test:
- Boot EFI GRUB2 from TianoCore payload
(Debian Live, Ubuntu installer)
- Boot GRUB2 payload
Change-Id: I5ce4f5168586bf305969b2e24b6ee895c8552749
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45960
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The keyboard only works randomly, because SeaBIOS initializes PS/2
before the EC is ready.
Set the PS/2 timeout for SeaBIOS to 500 ms, to wait for the EC before
initializing the keyboard.
Test: keyboard works fine.
Change-Id: I2be75961035f04a7ffa6f7e1dbaabb1243b857f9
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45959
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPP_A19 and GPP_A20 set no connection, disables DdiPort1Hpd and DdiPort2Hpd
BUG=b:169690329
TEST=build and verify type-c(C0/C1) port functional normally
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I4405526ae777332d3c72041db7b4eda25ae31b8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46069
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: TH Lin <t.h_lin@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Refactor DPTF section of code under the baseboard devicetree
and overridetree. This makes override mechanism more simpler,
because not all the DPTF fields need to be overridden.
BUG=None
BRANCH=None
TEST=Built and tested on dedede system
Change-Id: I8e7cfe60c010ed4c07f9089325b289519e861f84
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
It builds same binary for ibase/mb899 using BUILD_TIMELESS=1
Change-Id: I947c4228641abc38a5cd75e51fa2f096fda95d6f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45280
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It builds same binary for intel/d945gclf using BUILD_TIMELESS=1
Change-Id: Ic48008719a9cf6942ae8cdaebaab6ba43e665489
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45281
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9f5a89946888be3ed033c2ee079f171a23404e90
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I6ddc3d0c50c5907e24644cea5979d064bea4acd1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45913
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Generated buils/dsdt.dsl for intel/kblrvp11 are same.
Change-Id: I41195be171b48f41fe2955e4639d8b770853d483
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46081
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Change-Id: I91f65fecdcdf41dc41f136e8d66bbf730343aef3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46078
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ie2b1b27c0715fc223e644c3df6c0e9cb876322c8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Generated 'build/dsdt.dsl' files are same.
Change-Id: I15b332033f3d492f9e01bb5f1eb25892dee418de
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Change-Id: I35dc4be65f0843c3c74695c443dd958676e6c12c
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Allow MRC training in SaGv low, mid and high frequencies.
TEST=Verify memory trains at low, mid and high SaGv point
through FSP debug logs enabled.
Change-Id: I0f60aad031ce9dfe23e54426753311c35db46c05
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45196
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix typo for power limit values under comment section in baseboard
BUG=None
BRANCH=None
TEST=Build for volteer system
Change-Id: I879b9587e863360bf4efda4099d96b42b904377e
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Tested on OCP deltalake. The console now shows up on the serial.
Change-Id: If4c412c1ca749f1feba47b2ce0beb52d0111be86
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
- This change is required to execute EC sync in coreboot instead
of depthcharge
Bug=none
Test=build and boot coreboot on TGLRVP
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I40ae104d4de93c12097e049253a33b23a46c6203
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44689
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Bug=none
Test=emerge build and boot on tglrvp and check that
tpm is probed successfully from coreboot.
Cq-Depend:chromium-review:1881839
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I4a3aec98f72524e8e2a1834878ef75b9f933ae3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
|
|
Add trackpad, touchscreen, and usb port to devicetree
BUG=b:160664447
BRANCH=NONE
TEST=build bios and verify theirs function for boten
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: I057f7d15d20d1a78acd733cc5463357e9c87afb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add SPD support for DDR4 memory part H5ANAG6NCJR-XNC.
Eldrid should use DRAM_ID strap ID 4 (0100) on SKUs populated
with H5ANAG6NCJR-XNC DDR4 memory parts.
BUG=b:161772961
TEST="FW_NAME=eldrid emerge-volteer coreboot" and verify it builds
successfully.
Change-Id: Ia26315479ce1a749a0f7c9e81f134f7068d7eb0b
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=Boot dirinboz, run integrity test, b:169940185
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I6bac8284b67070ff2c5838257f4ae2ead0e69c22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45934
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=WIP
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I1191d73a2a3f72f99de187a946162460acbb287a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45935
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=WIP
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I2fcbe35103020c3444902c077b4985f87f970671
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45936
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=Boot on Vilboz with emmc
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I9a1e47dbee3fcc7317857d40c5418be30d755d61
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45933
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ethernet hardware on jecht variants doesn't support AER, so
disable it to mitigate continuous AER timeout errors in dmesg:
> pcieport 0000:00:1c.0: AER: Corrected error received: 0000:00:1c.0
> pcieport 0000:00:1c.0: AER: PCIe Bus Error: severity=Corrected, type=Data Link Layer, (Transmitter ID)
> pcieport 0000:00:1c.0: AER: device [8086:9c94] error status/mask=00001000/00002000
> pcieport 0000:00:1c.0: AER: [12] Timeout
Change-Id: Ieda82c6e13c2bbc4b3a051a3d2a7ae90728ccdc6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46137
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ethernet hardware on beltino variants doesn't support AER, so
disable it to mitigate continuous AER timeout errors in dmesg:
> pcieport 0000:00:1c.0: AER: Corrected error received: 0000:00:1c.0
> pcieport 0000:00:1c.0: AER: PCIe Bus Error: severity=Corrected, type=Data Link Layer, (Transmitter ID)
> pcieport 0000:00:1c.0: AER: device [8086:9c94] error status/mask=00001000/00002000
> pcieport 0000:00:1c.0: AER: [12] Timeout
Change-Id: I0f592a21d08e79cda251e80cd1f1184c4311e9df
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46136
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A SATA drive may be connected to SATA0.
BUG=b:162909831
BRANCH=puff
TEST=none
Change-Id: I2a4ce2f89fa6d786358e01add15f2eedfbe4b20f
Signed-off-by: Sam McNally <sammc@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
