| Age | Commit message (Collapse) | Author |
|---|
|
CLK_B1(GPIO_80) and DATA_2(GPIO_83) pins needs to be
configured as native mode to use them for DMIC record
on other potential DMIC's.
DMIC blobs configure the clocks. For stereo & quad channel
record, both CLK_A1 and CLK_B1 are enabled.
For mono channel record, only CLK_A1 is enabled.
BUG=chrome-os-partner:56918
BRANCH=None
TEST=During DMIC record, check CLK_B1 and DATA_2 lines
Change-Id: I838009b85190de5360d593238e48c9593c1dc43a
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/17199
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Note that currently, traps are only handled by the trap handler
installed in the bootblock. The romstage and ramstage don't override it.
TEST=Booted emulation/spike-qemu and lowrisc/nexys4ddr with a linux
payload. It worked as much as before (Linux didn't boot, but it
made some successful SBI calls)
Change-Id: Icce96ab3f41ae0f34bd86e30f9ff17c30317854e
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/17057
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Ron's code calculated the DLL and DLM registers of the 8250 UART, but
that's the job of the UART driver. uart_input_clock_divider isn't needed
anymore because the default value of 16 works.
As a bonus, the baud rate can now be selected in Kconfig, instead of
being hardcoded at 115200.
TEST=Booted the board at 9600 and 115200 baud.
Change-Id: I3d5e49568b798a6a6d944db1161def7d0a2d3b48
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/17188
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This brings the frequency down to 400kHz which is spec for
fast i2c.
BUG=chrome-os-partner:58889
Change-Id: Ibc5f152e55ed618f18ac6425264f086b1f2d1ffa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17215
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This brings the frequency down to 400kHz which is spec for
fast i2c.
BUG=chrome-os-partner:58889
Change-Id: I8689a062b5457aa431eaa7fb688a7170dad83fcf
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17214
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
1. Update dq, dqs map & Rcomp strength & Rcomp target.
2. Fix rvp3.spd.hex byte 2 to 0x0F(JEDEC LPDDR3 memory type).
Change-Id: I7efc3499b915d1e414cfe914830232993ef10ba2
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17162
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
1. Update gpio.h to set proper pad config for Kaby Lake RVP3.
2. Set spd index to zero.
3. Remove nhlt specific init.
Change-Id: I41a312d92acd2c111465a5e8f1771158e3f33e2b
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17161
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There are two configs, sdram-lpddr3-hynix-2GB.inc and
sdram-lpddr3-samsung-2GB-24EB.inc that use .ddrconfig = 14.
Changing .ddrconfig from 14 to 3 improves performance
especially on contiguous memory accesses. Comparing the .ddrconfig:
- if .ddrconfig = 3,
C RDRR RRRR RRRR RRRR RBBB CCCC CCCC C---
- if .ddrconfig = 14,
C DRBB BRRR RRRR RRRR RRRR CCCC CCCC C---
where
- R: indicates Row bits
- B: indicates Bank bits
- C: indicates Column bits
- D: indicates Chip selects bits
.ddrconfig = 3 has multiple banks switching which improves DDR timing.
BUG=chrome-os-partner:57321
TEST=Boot from fievel and play video
BRANCH=veyron
Change-Id: Ifdcedc28e84429b8b79c7553b38b667631d29c09
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 93882e4f2000d93c9dae5e6d4b2e1f4b7bc9489e
Original-Change-Id: Ic98ebae48609a7604ec678b6bd14dd2b29b669c4
Original-Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/404691
Original-Commit-Ready: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Tested-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17210
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add the new samsung DDR configs for all veyron except veyron_rialto:
* K4E6E304EB-EGCE, ramid = 0010, 4GB
* K4E8E324EB-EGCF, ramid = 1100, 2GB
BRANCH=veyron
BUG=none
TEST=boot fievel board
Change-Id: I747aa86f8c93174651a28face63b3386e22b23b3
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 5f55462e71bd481eda85af3d582cfe5b9873cc9c
Original-Change-Id: I19123634c994f685683323f7d85cc4d35814e2ab
Original-Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/345748
Original-Commit-Queue: Ren Kuo <ren.kuo@quantatw.com>
Original-Reviewed-by: Philip Chen <philipchen@chromium.org>
Original-(cherry-pick from cc990f27024255a326fd9fa9644deb28b01a31a7)
Original-Reviewed-on: https://chromium-review.googlesource.com/404690
Original-Commit-Ready: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Tested-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17209
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
framebuffer address is dynamically chosen by libpayload now, so there's
no need to configure it in coreboot.
CQ-DEPEND=CL:401402
BUG=chrome-os-partner:58675
BRANCH=none
TEST=Boot from kevin, dev screen is visible
Change-Id: I9f1e581d5c63b3579b26be22ce5c8d1e71679f6f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b3b6675420592c30e1e0abc8f8e9dd6ed5abd04c
Original-Change-Id: I7e3162f24a4dc426fe4e10d74865cf0042c80db5
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/401401
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17109
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
To enable DDR Dynamic Voltage and Frequency Scaling (DVFS) we need to
train alternative configurations first, so do the training and store the
values.
BUG=None
BRANCH=None
TEST=Boot from kevin
Change-Id: I944a4b297a4ed6966893aa09553da88171307a42
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 94533ff3ba21bcb0ace00bedcf0cebb89a341be2
Original-Change-Id: I4a98bc0db5553d154fedb657e35b926a92aa80c7
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/386596
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17104
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add the eve board files using kabylake and FSP 2.0.
BUG=chrome-os-partner:58666
TEST=build and boot on eve board
Change-Id: I7ca71fe052608d710ee65d078df7af7b55d382bc
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17177
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
This was tested at the coreboot meeting in Berlin.
The uart programming may still not be right but when used with
the lowrisc bitstream for the board we were able to load
and start linux, although it does not yet get far due to
PTE version issues with lowrisc.
Change-Id: Ia1de1a92762631c9d7bb3d41b04f95296144caa3
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/17132
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
This patch updates the _ART table with other external sensor
TSR0 for Fan speed control on Skylake-U based Kunimitsu and
Lars boards.
Also, updates the temperature values in DPTF policy for
better performance.
BUG=chrome-os-partner:51025
BRANCH=firmware-glados-7820.B
TEST=Built and booted on kunimitsu and lars EVT boards.
Verified this updated _ART table on these boards with
different workloads.
Change-Id: Ib195910c5eb00e004e8b9bd50e266ade3c175be2
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/332349
Reviewed-on: https://review.coreboot.org/17066
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
In certain cases a board variant may need to override the NHLT
OEM strings in the main NHLT table. Therefore, provide that path.
BUG=chrome-os-partner:56918
Change-Id: I57cc4fd3665698e41ceebb1949180f86bb60b61f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17167
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
|
|
Going forward GPIO_17 is used to determine the configuration of
the board w.r.t. the number of DMICs on the board.
BUG=chrome-os-partner:56918
Change-Id: I03edb880e0649977030c1b87219ebebac631a519
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17163
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
In RS485 mode RTS line acts as a transceiver direction control.
The datasheet is not very clear about the polarity but register setting
here is tested to drive nRTS line high when transmitting.
Also note revision of B of the super-IO has errata and 8N1 setting does
not work properly, you would need revision C of the chip assembled to
fix this.
Change-Id: I705fe0c5a5f8369b0a9358a64c74500238b5c4ba
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14998
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
In anticipation of getting fixed material remove the disabling of
periodic training for MT53B512M32D2NP and MT53B256M32D1NP.
BUG=chrome-os-partner:59003
Change-Id: Iaadaa979d85cab78dda527db7480420af02fd832
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17130
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Explain the reasoning for the part_num strings used in the
memory SKU table explaining the necessity of keeping mosys
in sync with the strings used. It's possible that actual part
numbers could change as the higher speed material gets cheaper,
for example.
BUG=chrome-os-partner:58966
Change-Id: If895e52791dc56e283261b3438106116b8b2ea05
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17129
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Remove the FADT from the individual mainboards and select and
use COMMON_FADT in the SOC instead. Set the ACPI revision to 5.
Change-Id: Ieb87c467c71bc125f80c7d941486c2fbc9cd4020
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17138
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=chrome-os-partner:57846
Change-Id: Ibd3ef8cebcf99ee2186dfed98b04373dd17e798e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17093
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Those registers are only used on more recent Intel platforms featuring a
PCH. The DP registers on G4X hardware are at a different offset.
Change-Id: Ib49e54d4e7d6595dc09fb1be35ac8178b80c7f71
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17110
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
According to: "Intel ® 4 Series Chipset Family datasheet"
the IGD only has 1 IRQ pin.
Change-Id: I974f002f5a213056f4593a1eab10772527bb241d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17098
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add support for Kaby Lake RVP3.
Use kunimitsu at commit 028200f as base.
Kabylake RVP3 is based on Kabylake-Y with onboard Dual Channel
LPDDR3 DIMM.
* Update board name to kblrvp
* Remove fsp 1.1 specific code( As Kabylake uses fsp2.0)
* Remove board id function.
* Remove unused spd & add rvp3 spd file.
This is an initial commit does not have full support to boot.
Will add more CLs to boot Chrome OS with depthcharge.
Change-Id: Id8e32c5b93fc32ba84278c5c5da8f8e30c201bea
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17032
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
CQ-DEPEND=CL:379684
BUG=chrome-os-partner:58064
TEST=verified on hana rev0
Change-Id: Icd076dcaf07a97f3b83b428b9619e8a4dafe744d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7c483951a0dcd419735fffb79e6187f9ca3b08a8
Original-Change-Id: I9d886abf15931496ac61e8fd38d7fd306f2a1bf7
Original-Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/379504
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Philip Chen <philipchen@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17107
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There are some sdram configurations that are no longer used. Drop them.
BUG=None
BRANCH=None
TEST=None
Change-Id: Ib6d2d58c3071147a3095bc1ed7fa7b02c748e1a5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 111d375005ec6a3b91e47acdd676e8f1644c931c
Original-Change-Id: I5f9278093f02e785b2894faa8e8cf09ecec20325
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/399122
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17103
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We found sdram may fail in pctl_cfg(), so we check the status in this
function. If it exceeds 100ms still in this function, we will restart
the system. We also found there are rare chances DDR training fails,
so also restart system in that case.
BUG=chrome-os-partner:57988
BRANCH=None
TEST=coreboot resets on failure and eventually the system comes up
Change-Id: Icc0688da028a8f4f81eafe36bbaa79fdf2bcea74
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 89e45f8352f62e19a203316330aba14ccc5c8b11
Original-Change-Id: If4e78983abcfdfe1e0e26847448d86169e598700
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/397439
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17045
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
It's a better default than QEMU-armv7, which is currently the default
board when coreboot is configured for the first time, because most
coreboot development targets x86.
With this patch, the minimal steps to coreboot+SeaBIOS booting in QEMU
become:
git clone https://review.coreboot.org/coreboot.git && cd coreboot
make crossgcc-x86
make olddefconfig && make
qemu-system-x86_64 -bios build/coreboot.rom
Change-Id: Ie44a5d95547a55df93f29082c3b5a86fb83aa1e7
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/16987
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Define reset_gpio and enable_gpio for touchscreen device so that when
kernel puts this device into D3, we put the device into
reset. PowerResource _ON and _OFF routines are used to put the device
into D0 and D3 states.
BUG=chrome-os-partner:55988
Change-Id: Ia905f9eb630cd96767b639aec74131dbd7952d0e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17083
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Change-Id: I627338505fe1273366bc8f6f528d829b3162b371
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16916
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I7515288190ca57a321fb8ffe57a1181b638c336a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16978
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I2fae9e02e2fccaff97f2441fd17f8960e8ab9786
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16975
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ife9c0b8a1ab55fe683c88e34239d7f5806e1ff9b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16971
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I765814450b82755f84c010f63bc8f919bb0cd4c1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16970
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This version of coreboot successfully starts a Harvey (Plan 9) kernel as a payload,
entering main() with no supporting assembly code for startup. The Harvey port
is not complete so it just panics but ... it gets started.
We provide a standard payload function that takes a pointer argument
and makes the jump from machine to supervisor mode;
the days of kernels running in machine mode are over.
We do some small tweaks to the virtual memory code. We temporarily
disable two functions that won't work on some targets as register
numbers changed between 1.7 and 1.9. Once lowrisc catches up
we'll reenable them.
We add the PAGETABLES to the memlayout.ld and use _pagetables in the virtual
memory setup code.
We now use the _stack and _estack from memlayout so we know where things are.
As time goes on maybe we can kill all the magic numbers.
Change-Id: I6caadfa9627fa35e31580492be01d4af908d31d9
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/17058
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I2a3bf53e6bc4084305238fa176ae46161da4be8f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16967
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I4e628cbe11da32d291c4b8e4c7be91e9b0a86ad9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16966
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I137b27ffb0e54a9ca6b0bd3a454b1d99b3e1c22b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16907
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add choice to select between FSP 1.1 & FSP2.0 driver to be used.
Change-Id: Ied7eab6f4a2191e0bcf220cde5ca519a3c3e2d76
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17051
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Create the initial Snappy variant which refers to the Reef device.
Snappy, an Apollolake-platform, is deviated from reference board Reef.
BRANCH=master
BUG=None
TEST=Built & booted
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I6f32c0b1a154edbd8c4822acdbdbdbeb4a0098e6
Reviewed-on: https://review.coreboot.org/17043
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
MAINBOARD_HAS_NATIVE_VGA_INIT_TEXTMODECFG should only occur together with
MAINBOARD_HAS_NATIVE_VGA_INIT. It seems to be used to just have to have
the option to be able to select SEABIOS_VGA_COREBOOT.
This patch makes these boards use MAINBOARD_DO_NATIVE_VGA_INIT and
MAINBOARD_HAS_NATIVE_VGA_INIT to have it select SEABIOS_VGA_COREBOOT
by default when SeaBIOS is chosen.
Change-Id: If0a36af1883a3d62b16a61483733be981a85e5e2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16981
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Configure GPIO 122 as PERST on DVT. This is to assert WiFi PERST
during s0ix entry.
BUG=chrome-os-partner:55877
TEST=S0ix functional on DVT
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Change-Id: Iab18b2de621a1a9226c78493f6defa15081db875
Reviewed-on: https://review.coreboot.org/17030
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Reef is using APL SoC SKU's with 6W TDP max. We've done
experiments and found the energy calculation is wrong with
the current VR solution. Experiments show that SoC TDP max
(6W) can be reached when RAPL PL1 is set to 12W. Therefore,
we've inserted 12W override after reading the fused value (6W)
so that the system can reach the right performance level.
BUG=chrome-os-partner:56922
TEST=webGL performance(fps) not impacted before and after S3.
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Change-Id: I21c278e82b82d805f6925f4d9c82187825fd0aa0
Reviewed-on: https://review.coreboot.org/17029
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
TEST=Compiled for and ran on spike; it booted as before.
Change-Id: Id173643a3571962406f9191db248b206235dca35
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/16995
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
spike_util.h:
- (LOG_)REGBYTES and STORE are already defined in
arch/riscv/include/bits.h.
- TOHOST_CMD, FROMHOST_* are helper macros for the deprecated
Host-Target Interface (HTIF).
qemu_util.c:
- mcall_query_memory now uses mprv_write_ulong instead of first
translating the address and then accessing it normally. Thus,
translate_address isn't used anymore.
- Several functions used the deprecated HTIF CSRs mtohost/mfromhost.
They have mostly been replaced by stub implementations.
- htif_interrupt and testPrint were unused and have been deleted.
spike_util.c:
- translate_address and testPrint were unused and have been deleted.
After this commit, spike_util.c and qemu_util.c are exactly the same and
can be moved to a common location.
Change-Id: I1789bad8bbab964c3f2f0480de8d97588c68ceaf
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/16985
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I277cc9ae22cd33f2cd9ded808960349d09e8670d
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/16984
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Regardless of the payload chosen a file etc/ps2-keyboard-spinup
is added to cbfs. With this fix this file is only added to cbfs when
seabios is choses as a payload.
Change-Id: I37cf4c998856db2d297356776752643dba46a8f8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16146
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Requesting low power acpi cpu c-states has two software interfaces:
Using P_LVLx I/O reads or using equivalent MWAIT requests.
This change makes it more consistent with newer targets that use MWAIT
requests.
There also exists extended intel acpi c-states which can be enabled
in two ways:
- using a substate hint to the mwait request (defined in bios);
- setting a model specific register (msr)
Currently this is done by setting the right msr bits but with this
change one can experiment by adding substate hints.
Change-Id: I9eeb5b008e2ddc2193725667f2c13582a4877e3c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/14801
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I81c32c618627507cc3a83f60f565a73e5e6d7a13
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16913
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I0014fc030888d71f7951c97bccc7cef0e1c45186
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16922
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch adds MAINBOARD_HAS_NATIVE_VGA_INIT_TEXTMODECFG to the
gigabyte/ga-g41m-es2l Kconfig to allow selecting between textmode and
vesamode in menuconfig.
Change-Id: I84b61118fa0419d49d2498b66029711cdce97576
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16501
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ib44bc66e02901dbde14361091a049f71c3ecb840
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16921
Tested-by: build bot (Jenkins)
Reviewed-by: Kerry Sheh <shekairui@gmail.com>
|
|
Change-Id: I416d3c212653260a28cb07ed86fda34b736ba4ca
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16926
Tested-by: build bot (Jenkins)
Reviewed-by: Kerry Sheh <shekairui@gmail.com>
|
|
Maxim98357a speaker amp requires BCLK & SFRM to be active
and stable before it is unmuted. If there is a BLCK and no
SFRM, it results in a pop sound.
sdmode_delay property already exists which facilitates this
configuration. This patch updates "sdmode_delay" to avoid
pop sound.
BUG=chrome-os-partner:58356
BRANCH=None
TEST=while audio playback via headset, remove headset.
Audio will be switched playback to speaker. Observe if
pop sound comes from speaker.
Change-Id: I7ad68caa88d7b3ff52ac1379fe6564de27d97777
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/16933
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Change-Id: I53a0344686921012f4e031842b5108aa4a7b79b1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16908
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ia1e7f558bbc44001358339a522e59a2ef7c420fb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16923
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Some PVT units encountered DRAM calibration failure during
power on/off tests. The failure is caused by higher impedance
of the DRAM on those units. So increase the driving strength
for 4GB DRAMs.
BUG=chrome-os-partner:57392
TEST=run cold reboot 100 times on PVT units which have DRAM
calibration issue.
Change-Id: I8a329093db3f1def566e4b7afec3c4f4bfe44c6a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cf1aa5ade856af433fa056f51a20d18553ae241d
Original-Change-Id: I0d1776cd1a5892d1f82e9bf414620d1ef6d29132
Original-Signed-off-by: PH Hsu <ph.hsu@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/394451
Original-Commit-Ready: Yidi Lin <yidi.lin@mediatek.com>
Original-Tested-by: Yidi Lin <yidi.lin@mediatek.com>
Original-Reviewed-by: Pin-Huan Hsu <ph.hsu@mediatek.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/16917
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We found that Kevin board PHY0 and PHY1 eye-diagram margin
is not enough to make compliance test pass, and the PHY0 USB
SI is worse than PHY1, because of the higher PCB impedance.
For PHY0, we can't improve the eye-diagram by SW PHY tuning,
so we need to reduce the RBIAS resistance from 133 ohm to 115
ohm, it can help to increase the eye-height.
For PHY1, we can improve the eye-diagram by setting the max
pre-emphasis level.
And after the above change, the USB2 signal amplitude will
become larger at the test point near to SOC USB2 PHY, in order
to avoid mis-trigger the disconnect detection (650mV), we need
to disable pre-emphasize in eop state.
BRANCH=None
BUG=chrome-os-partner:53863
TEST=do USB 2.0 compliance test for Kevin C0 and C1 port.
Change-Id: I95c0acd79623aeca9a0ae077b1dd3836d91fe561
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: de3cdef128966d76e7d8e2ebd641763b911c3ad5
Original-Change-Id: I00cb325b9938e4276cc77b5d6f5faa7023379608
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/390615
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16911
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
commit 028200f7 - x86/acpi_device: Add support for GPIO output polarity
updated ACPI_GPIO_OUTPUT to ACPI_GPIO_OUTPUT_ACTIVE_HIGH for the other
boards that needed it, but pyro wasn't in the tree when it was initially
pushed. Now that pyro is in the tree, it needs to be updated as well.
Change-Id: I617999b06ee584e0543d7ae3232bb2be2ff7429c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16930
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ie2a047d35e69182812c349daedc5b3b5fde20122
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16860
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I35cb7e08d5233aa5a3dbb4631ab2ee4dc9596f98
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16849
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Instead of hard-coding the polarity of the GPIO to active high/low,
accept it as a parameter in devicetree. This polarity can then be used
while calling into acpi_dp_add_gpio to determine the active low status
correctly.
BUG=chrome-os-partner:55988
BRANCH=None
TEST=Verified that correct polarity is set for reset-gpio on reef.
Change-Id: I4aba4bb8bd61799962deaaa11307c0c5be112919
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/16877
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
GPIO1_B3 (WLAN_MODULE_RST#) defaults as a pull-up input, but it is also
"pulled up" by 1.8V_WLAN. However, 1.8V_WLAN remains low for some time
during early boot. This leaves the signal floating somewhere in the
middle.
This has two potential issues:
(1) we're leaking some power for some (hopefully) short period of time
(2) we are possibly screwing with the Wifi power sequence; we aren't
supposed to deassert PDn (i.e., MODULE_RST#) until all the rails
have fully ramped for some period of time
Neither of the above issues are likely to be significant, but it is nice
to fix, I expect.
BRANCH=gru
BUG=chrome-os-partner:54026
TEST=measure WLAN_MODULE_RST# on scope at boot time
Change-Id: Ia6af9ad6954ad8feeda33015e3f205842380939e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0e890a2787bf034d3358a33fc88c2dd8078593ab
Original-Change-Id: I120e26ad0ca486a326874986e142dcaee965b62d
Original-Signed-off-by: Brian Norris <briannorris@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/388009
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16882
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
PHY_PER_CS_TRAINING is being enabled when DDR frequency >= 666.
For per cs training, the controller should consider the PHY
delay line switch time and there should be more cycles to
switch the delay line, so update the W2W_DIFFCS_DLY_ value
from 0x1 to 0x5.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=do memtester on kevin board, and pass
Change-Id: I00df2d4724b0b77f3e7565809fb35bbd2ff01ea5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c135ea3e33d810ed322d947eb8d512d1ac119cfc
Original-Change-Id: I81b99cbc085769b7028e770509d79bd8d550820b
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/387506
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16721
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
To save power when entering suspend, gpios 2 to 4 need to be set
to input and 'pull none' mode.
Pass the APIO configuration to ATF so it can do a proper job here.
BRANCH=None
BUG=chrome-os-partner:56423
TEST=run suspend_stress_test on kevin board
Change-Id: Id57fe8f622ae3f9c2bc7e58be89518b2b846cd37
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9c42082d1ca9a6baa735821382d3e83c1f8dc9ad
Original-Change-Id: Iaf441e8e34c5591ffe7c65f6533fcf0b733ff5ac
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/378475
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16720
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We need to disable some regulators when the device goes into suspend.
This means that we need to pass some gpios to bl31, and disable these
gpios when bl31 runs the suspend function.
BRANCH=None
BUG=chrome-os-partner:56423
TEST=enter suspend, measure suspend gpio go to low
[pg: also update arm-trusted-firmware to match]
Change-Id: Ia0835e16f7e65de6dd24a892241f0af542ec5b4b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0f3332ef2136fd93f7faad579386ba5af003cf70
Original-Change-Id: I03d0407e0ef035823519a997534dcfea078a7ccd
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/374046
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16719
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Create the initial Pyro variant which refers to the Reef.
Pyro is APL Chrome board that deviate from reference board Reef.
BRANCH=master
BUG=None
TEST=Build
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Change-Id: I9beed1f6895e8891d3d51b563edfe172f566718b
Reviewed-on: https://review.coreboot.org/16855
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
To improve sdram 800MHz and 933MHz stability, we
need to modify write leveling flow to get the
proper write leveling value.
BUG=chrome-os-partner:56940
BRANCH=none
TEST=Boot from kevin on 933MHz, and do stressapptest
Change-Id: I5b24c93d4a57917fb9af7e5e2a95d8423ccbaa7e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d84bf25b3e5de373c7913e6d534a810cb984b3fd
Original-Change-Id: I87efddf628c3683fcb85d6875e029cf3cbc482be
Original-Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Original-Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/384292
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16716
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since there's currently a limitation in coreboot's code that prevents
more than 4KB to be used by the eventlog anyway, this patch shrinks the
available RW_ELOG area in the FMAP for Gru down to 4KB. This may prove
prudent later if we ever resolve that limitation, so that tools can rely
on the area in the FMAP being the same as the area actually used by the
read-only firmware code on these boards.
BRANCH=gru
BUG=chrome-os-partner:55593
TEST=Booted Kevin, confirmed that eventlog got written normally. Ran a
reboot loop to exhaust eventlog space, confirmed that the shrink code
kicks in as expected before reaching 4KB.
Change-Id: I3c55d836c72486665a19783fe98ce9e0df174b6d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 05efb82ca00703fd92d925ebf717738e37295c18
Original-Change-Id: Ia2617681f9394e953f5beb4abf419fe8d97e6d3e
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/384585
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Simon Glass <sjg@google.com>
Reviewed-on: https://review.coreboot.org/16715
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
sdram noc timing will affect ddr latency, this patch improves
rk3399 sdram noc timing so improve memory performance.
BRANCH=gru
BUG=chrome-os-partner:57248
TEST=Boot from kevin board
Change-Id: I09e984490a7ad747ef8abfc6542d0e2c95ec19bc
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 43dfe55d713d371e39d21312772fd353614b7642
Original-Change-Id: I393e74ecdeb72930ac38ae9bcf311e5654f65162
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/382725
Original-Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Sonny Rao <sonnyrao@chromium.org>
Original-Commit-Queue: Sonny Rao <sonnyrao@chromium.org>
Reviewed-on: https://review.coreboot.org/16713
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We found some boards are not stable when sdram is run at 933Mhz.
Before we can fix it, we need to lower the sdram frequency to 800MHz.
In this patch we modify the DQS delay from 0x280 to 0x260 and extend
the DQS window.
BRANCH=None
BUG=chrome-os-partner:56940
TEST=Booted Kevin.
Change-Id: I68561c4aa4d9ab66acfa3515a42d696157aff759
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 877a7f6ad22a5bde9f9e458bcb65f133f2f001bd
Original-Change-Id: I5eab6bbe96f0dae095c5353403292022e7a25421
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/382724
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Tested-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16709
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add lpddr3-K4E6E304EB-2GB-1CH memory configuration for rialto.
BUG=chrome-os-partner:56759
BRANCH=none
TEST=Build
Change-Id: I698fe450d48b64a06232aa44ecf91d688d9dc17a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d3edecdb135939c3264ab1b831e7821d3a3e0149
Original-Change-Id: I7dae9fd822abeff5b08de0ab9262e1817ac58531
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/380443
Original-Commit-Ready: Alexandru Stan <amstan@chromium.org>
Original-Tested-by: Alexandru Stan <amstan@chromium.org>
Original-Reviewed-by: Alexandru Stan <amstan@chromium.org>
Original-Reviewed-by: Jonathan Dixon <joth@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16699
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch moves the big CPU cluster initialization on the RK3399 from
the clock init bootblock function into ramstage. We're only really doing
this to put the cluster into a sane state for the OS, we're never
actually taking it out of reset ourselves... so there's no reason to do
this so early.
Also cleaned up the interface for rkclk_configure_cpu() a bit to make it
more readable.
BRANCH=None
BUG=chrome-os-partner:54906
TEST=Booted Kevin.
Change-Id: I568b891da0abb404760d120cef847737c1f9e3ec
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: bd7aa7ec3e6d211b17ed61419f80a818cee78919
Original-Change-Id: Ic3d01a51531683b53e17addf1942441663a8ea40
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/377541
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16698
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Due to different LCD panel requirements the delay between LVDS becomes
active and the backlight is switched on needs to be increased to 500 ms.
Change-Id: I09029624469aef412141c7b46224d48557ba4af1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16875
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Several of the special function pins we're using in firmware have a
pre-assigned pull-up or pull-down on power-on reset. We don't want those
to interfere with any of the signaling we're trying to do on those pins,
so this patch disables them.
Also do some house-cleaning to group the bootblock code better, and
change the setup code for all SPI and I2C buses to first initialize the
controller and then mux the pins... I assume this might be a little
safer (in case the controller peripheral has some pins in a weird state
before it gets fully initialized, we don't want to mux it through too
early).
BRANCH=None
BUG=chrome-os-partner:52526
TEST=Booted Kevin.
Change-Id: I4d5bd3f7657b8113d90b65d9571583142ba10a27
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f8f7fd56e945987eb0b1124b699f676bc68d0560
Original-Change-Id: I6bcf2b9a5dc686f2b6f82bd80fc9a1a245661c47
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/382532
Reviewed-on: https://review.coreboot.org/16711
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Increase the SPI bus speed to speed up boot time. The maximum supported
speed at 1.8V is 37.5MHz, and 33MHz is the next lowest convenient speed,
given the clock parents.
BUG=chrome-os-partner:56556
BRANCH=none
TEST=boot on gru and see that things still work correctly. Total time
spent on reading from SPI reduces from 185ms to 141ms.
Change-Id: I71436c9e343b18360fa63d528dea5cfcfbc831e6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d7576f6e53e407af61160be142c3d589e864a8cf
Original-Change-Id: I55a19f523817862e081d23469e94fd795456dd67
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381313
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Simon Glass <sjg@google.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16708
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
If we setup the PWM _after_ the pinmux then there's a period of time
when we're driving the PWM incorrectly. Let's setup the regulator and
_then_ configure the pinmux.
This fixes no known bugs, but it is more correct and probably makes the
signals look better at bootup.
BRANCH=None
BUG=None
TEST=scope
Change-Id: I311c0eded873b65e0489373e87b88bcdd8e4b806
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: fcf4d0ba29d82cce779c0b25ead36de4a95d97a1
Original-Change-Id: I5124f48d04a18c07bbd2d54bc08ee001c9c7e8d1
Original-Signed-off-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381592
Original-Reviewed-by: Simon Glass <sjg@google.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16700
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ia5ea2198cdc93822723a4fe5440d574d76cb4de2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16847
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The datasheets on gm45: "Mobile Intel® 4 Series Express Chipset Family"
mention the possibility of having 352M ram preallocated for the
integrated graphic device. This only worked fine if the amount of ram in
the system was 3GB or less. When 4G or more is installed, memory is
remapped to create a 1GB large pci mmio hole which is not enough and
creates conflicts when 352M vram is used.
This patch increases the pci mmio hole size on Lenovo x200 to allow
352M vram to work.
TEST: build and flash on target with 4GB ram or more, use nvramtool to
set gfx_uma_size to 352M and reboot.
Change-Id: I5ab066252339ac7d85149d91b09a9eaaaab3b5b6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16831
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I18de4740e0d3512ec81e10b32d13d07a35791b57
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16846
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Iab0c7c470a3105b5df7b6b74aebdd1329e7f93ba
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16859
Tested-by: build bot (Jenkins)
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
On-board memory is on channel 1.
This fixes native raminit with 4GiB SO-DIMM installed.
Change-Id: If1b94e050d7e8d0dbd349c0415a182730aa5fa90
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/16845
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Kconfig symbols of type bool are ALWAYS defined, so this code was
always being included and run, which isn't what the author wanted.
Change to use IS_ENABLED(), and a regular if() instead of an #ifdef.
Change-Id: I72623fa27e47980c602135f4b73f371c7f50139b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16837
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Everybody knows WHAT they're supposed to do with options, so the text
"Pick this" or "Select to" are redundant.
Change-Id: I327c5be755373e99ca0738593bd78e1084d4d492
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16838
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I1559a2541a93a9969ac68708a04f0468790feb69
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16844
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: Ida10672380f6dffec0daf0073f25f6badfcd83eb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16843
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I2714553e2521f8178538755e3cfadec5c1fc6b12
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16842
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Kconfig hex values don't need to be in quotes, and should start with
'0x'. If the default value isn't set this way, Kconfig will add the
0x to the start, and the entry can be added unnecessarily to the
defconfig since it's "different" than what was set by the default.
A check for this has been added to the Kconfig lint tool.
Change-Id: I86f37340682771700011b6285e4b4af41b7e9968
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16834
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add Imac5,2 based on macbook2,1 port.
Change-Id: I34c8313c32920b02a2b964d8718e5b2b6b5a6820
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16638
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Idb37abea01831631aadba66ecd42bc7df03aa857
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/16727
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Replace the use of the old device_t definition inside
mainboard/biostar/am1ml.
Change-Id: Iba2fff5617c62152355b54e446517ad36108aa31
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16688
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch increases the CPU specific passive temp. trip point
and critical temp. trip point value for DPTF policy.
BUG=chrome-os-partner:57903
TEST=Built, booted on reef and verified this passive and
critical temp. trip points with heavy workload.
Change-Id: I2a38d01a6539c1bd478f8716c4b543ebcd1f2080
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/16766
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
|
|
For all mainboard variants use the "Google_Reef" family by default
which is populated in SMBIOS tables. A variant can provide their own
value if needed, but "Google_Reef" can reside as the family without
having to add conditions for each variant when MAINBOARD_FAMILY
have to be overridden.
BUG=chrome-os-partner:56677
Change-Id: Ic214eae1e6473b32f4cb442c09c34355357e1257
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16813
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: If47f0c072399fe8291bd8e41920d828f649ec49f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16817
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: Id46a0c4ca59dc7224c2eedd674ea3a5486509de1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16824
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ib439e5d96543790d17934bd477af62d39a5958b6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16815
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Id97981a05ce4af371c765c6950ed504557b0a584
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16825
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Iaf5ad440cfc2bbe08ea9f6c545e5e314645c8893
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16823
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I3040dc9a2534a77087805ee61c4f91d1bdb4d509
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16822
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I39ad6606869f059b2ef0c45d6741b844b3791655
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16821
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
