| Age | Commit message (Collapse) | Author |
|---|
|
This makes use of the new functions from pmutil.c that take
care of the differences between -H and -LP chipsets.
It also adds support for the LynxPoint-LP GPE0 register block
and the SMI/SCI routing differences.
The FADT is updated to report the new 256 byte GPE0 block on
wtm2/wtm2 boards which is too big for the 64bit X_GPE0 address
block so that part is zeroed to prevent IASL and the kernel
from complaining about a mismatch.
This was tested on WTM2. Unfortunately I am still unable to get an
SCI delivered from the EC but I suspect that is due to a magic
command needed to put the EC in ACPI mode. Instead I verified that
all of the power management and GPIO registers were set to expected
values.
I also tested transitions into S3 and S5 from both the kernel and
by pressing the power button at the developer mode screen and they
all function as expected.
Change-Id: Ice9e798ea5144db228349ce90540745c0780b20a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2816
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Changes:
- Get rid of the h8scm mainboard specific code and use the
platform generic function wrapper that was added in change
http://review.coreboot.org/#/c/2777/
AMD Fam15: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: I575221039ad65a59ae0f93397ef1038b669e81c7
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2829
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Changes:
- Get rid of the dinar mainboard specific code and use the
platform generic function wrapper that was added in change
http://review.coreboot.org/#/c/2777/
AMD Fam15: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
- select_socket() and restore_socket() were created from code that
was removed from AmdMemoryReadSPD() in dimmSpd.c. The functionality
is specific to the dinar mainboard configuration and was therefore
split from the generic read SPD functionality.
Change-Id: I1e4b9a20dc497c15dbde6d89865bd5ee7501cdc0
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2830
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Changes:
- Get rid of the s8226 mainboard specific code and use the
platform generic function wrapper that was added in change
http://review.coreboot.org/#/c/2777/
AMD Fam15: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
- select_socket() and restore_socket() started by duplicating
sp5100_set_gpio() and sp5100_restore_gpio(), which were in
dimmSpd.c. In addition to renaming the functions to more
specifically state their purpose, some cleanup and magic number
reduction was done.
Change-Id: I1eaf64986ef4fa3f89aed2b69d3f9c8c913f726f
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2827
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Changes:
- Get rid of the h8qgi mainboard specific code and use the
platform generic function wrapper that was added in change
http://review.coreboot.org/#/c/2777/
AMD Fam15: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
- select_socket() and restore_socket() started by duplicating
sp5100_set_gpio() and sp5100_restore_gpio(), which were in
dimmSpd.c. In addition to renaming the functions to more
specifically state their purpose, some cleanup and magic number
reduction was done.
Change-Id: I346ebd8399d4ba3e280576e667fdc62fa75a63b8
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2828
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This code is taken from an EDID reader written at Red Hat.
The key function is
int decode_edid(unsigned char *edid, int size, struct edid *out)
Which takes a pointer to an EDID blob, and a size, and decodes it into
a machine-independent format in out, which may be used for driving
chipsets. The EDID blob might come for IO, or a compiled-in EDID
BLOB, or CBFS.
Also included are the changes needed to use the EDID code on Link.
Change-Id: I66b275b8ed28fd77cfa5978bdec1eeef9e9425f1
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2837
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is a new state machine. It is more programmatic, in the
case of auxio, and has much more symbolic naming, and very few
"magic" numbers, except in the case of undocumented settings.
As before, the 'pre-computed' IO ops are encoded in the iodefs
table. A function, run, is passed and index into the table and
runs the ops.
A new operator, I, has been added. When the I operator is hit,
run() returns the index of the next operator in the table.
The i915lightup function runs the table. All the AUX channel ops
have been removed from the table, however, and are now called as
functions, using the previously committed auxio function.
The iodefs table has been grouped into blocks of ops, which end in
an I operator. As the lightup function progresses through startup,
and the run() returns, the lightup function performs aux channel
operations.
This code is symbolic enough, I hope, that it will make haswell
graphics bringup simpler.
i915io.c, and the core of the code in i915lightup.c, were
programatically generated, starting with IO logs from the DRM
startup code in the kernel. It is possible to apply the tools that
do this generation to newer IO logs from the kernel.
Change-Id: I8a8e121dc0d9674f0c6a866343b28e179a1e3d8a
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2836
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add a new operator, P, for the state machine, meaning
implement a palette fill.
Implement a function (palette) that fills the palette when the
P operator is hit.
This replaces 256 lines in the state machine table with 1.
Change-Id: I67d9219fe7de0ecf1fb9faf92130c00c9f5f8e88
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/2835
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
For full integration of FUI into coreboot, we need aux channel
communcations. The intel_dp.c is a file taken from Linux and is
used for aux channel comms. This file has been cut down to work
with coreboot. For now it is associated with the link mainboard
until we get a better handle on how this all fits together. This
code is almost certainly usable on other platforms in the long term.
But one step at a time.
Change-Id: I7be4c56e0a7903f3901ac86e12b28f3bdc0f7947
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/2834
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This adds a new API for cache maintenance operations. The idea is
to be more explicit about operations that are going on so it's easier
to manage branch predictor, cache, and TLB cleans and invalidations.
Also, this adds some operations that were missing but required early
on, such as branch predictor invalidation. Instruction and sync
barriers were wrong earlier as well since the imported API assumed
we compield with -march=armv5 (which we don't) and was missing
wrappers for the native ARMv7 ISB/DSB/DMB instructions.
For now, this is a start and it gives us something we can easily use
in libpayload for doing things like cleaning and invalidating dcache
when doing DMA transfers.
TODO:
- Set cache policy explicitly before re-enabling. Right now it's left
at default.
- Finish deprecating old cache maintenance API.
- We do an extra icache/dcache flush when going from bootblock to
romstage.
Change-Id: I7390981190e3213f4e1431f8e56746545c5cc7c9
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2729
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This fixes a trivial error with the recovery mode GPIO index.
Change-Id: I7290c1e23cdddaf91c9021d4e4252c0c772b6eab
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2825
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
A fix to eliminate warnings when building romstage files with ChromeOS
compilers
Change-Id: Ia5d7bbdde3aa3439fd493f5795f2cc2bf4c4c187
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2781
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Having this header file in the mainboard directory breaks
the dinar build on cygwin because the header file in the
dinar mainboard is used instead of the correct header file
src/vendorcode/amd/cimx/sb700/OEM.h. The build probably works
fine on Linux systems because, due to case-sensitivity, Oem.h
will not match the #include "OEM.h" statement in
src/southbridge/amd/cimx/sb700/Platform.h.
The Oem.h file in the dinar mainboard is not used by any other
source files, and the defines in the dinar mainboard are duplicated
by defines in the correct OEM.h file. Therefore, the file can be
safely removed.
Change-Id: I81b97eca8116d63644d335edc3bb51f90c7094d9
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2776
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
This commit pulls in all the common logic for romstage into
the Haswell cpu directory. The bits specific to the mainboard
still reside under their respective directories. The calling
sequence bounces from the cpu directory to mainboard then back
to the cpu directory. The reasoning is that Haswell systems use
cache-as-ram for backing memory in romstage. The stack is used to
allocate structures. However, now changes can be made to the
romstage for Haswell and apply to all boards.
Change-Id: I2bf08013c46a99235ffe4bde88a935c3378eb341
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2754
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
It was found that the Haswell reference code was smashing through the
stack into the reference code's heap implementation. The reason for this
is because our current CAR allocation is too small. Moreover there are
quite a few things to coordinate between 2 code bases to get correct.
This commit separates the CAR into 2 parts:
1. MRC CAR usage.
2. Coreboot CAR usage.
Pointers from one region can be passed between the 2 modules, but one
should not be able to affect the others as checking has been put into
place in both modules.
The CAR size has effectively been doubled from 0x20000 (128 KiB) to
0x40000 (256KiB). Not all of that increase was needed, but enforcing
a power of 2 size only utilizes 1 MTRR.
Old CAR layout with a single contiguous stack with the region starting
at CONFIG_DCACHE_RAM_BASE:
+---------------------------------------+ Offset CONFIG_DCACHE_RAM_SIZE
| MRC global variables |
| CONFIG_DCACHE_RAM_MRC_VAR_SIZE bytes |
+---------------------------------------+
| ROM stage stack |
| |
| |
+---------------------------------------+
| MRC Heap 30000 bytes |
+---------------------------------------+
| ROM stage console |
| CONFIG_CONSOLE_CAR_BUFFER_SIZE bytes |
+---------------------------------------+
| ROM stage CAR_GLOBAL variables |
+---------------------------------------+ Offset 0
There was some hard coded offsets in the reference code wrapper to start
the heap past the console buffer. Even with this commit the console
can smash into the following region depending on what size
CONFIG_CONSOLE_CAR_BUFFER_SIZE is.
As noted above This change splits the CAR region into 2 parts starting
at CONFIG_DCACHE_RAM_BASE:
+---------------------------------------+
| MRC Region |
| CONFIG_DCACHE_RAM_MRC_VAR_SIZE bytes |
+---------------------------------------+ Offset CONFIG_DCACHE_RAM_SIZE
| ROM stage stack |
| |
| |
+---------------------------------------+
| ROM stage console |
| CONFIG_CONSOLE_CAR_BUFFER_SIZE bytes |
+---------------------------------------+
| ROM stage CAR_GLOBAL variables |
+---------------------------------------+ Offset 0
Another variable was add, CONFIG_DCACHE_RAM_ROMSTAGE_STACK_SIZE,
which represents the expected stack usage for the romstage. A marker
is checked at the base of the stack to determine if either the stack
was smashed or the console encroached on the stack.
Change-Id: Id76f2fe4a5cf1c776c8f0019f406593f68e443a7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2752
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This is causing a hang in depthcharge. For now just disable
this port.
Change-Id: I87a6db2d8361588e82eee640c74cea690115bed5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2764
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Rather than have to repeat this bit in every mainboard.
Also, remove the reset of the RTC power status from here.
We had done this in TOT for current platforms but did not
carry it back to emeraldlake2 where this branched from.
If we clear the status here then we don't get an event
logged later which can be important for the devices that
do not have a CMOS battery.
Change-Id: Ia7131e9d9e7cf86228a285df652a96bcabf05260
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2683
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
We're happy to announce coreboot support for the "Stout"
Chromebook, a.k.a Lenovo X131e Chromebook.
Change-Id: I9b995f8d0dd48e41c788b7c3d35b4fac5840e425
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2636
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This is mostly a copy of Whitetip Mountain 1 with specific GPIO
map for this Customer Reference Board (CRB).
This mainboard currently has basic funcionality and is able to
boot a Linux Kernel but many of the new Haswell ULT specific
devices are not yet enabled.
Change-Id: I999452d86f00a2c245fa39b1b76080f6a3b1e352
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2725
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There was a mix of setup code sprinkled across the various components:
southbridge code in the northbridge, etc. This commit reorganizes the
code so that northbridge code doesn't initialize southbridge components.
Additionally, the calling dram initialization no longer calls out to ME
code. The main() function in the mainboard calls the necessary ME
functions before and after dram initialization.
The biggest change is the addition of an early_pch_init() function
which initializes the BARs, GPIOs, and RCBA configuration. It is also
responsible for reporting back to the caller if the board is being
woken up from S3. The one sequence difference is that the RCBA config
is performed before claling the reference code.
Lastly the rcba configuration was changed to be table driven so that
different board/configurations can use the same code. It should be
possible to have board/configuration specific gpio and rcba
configuration while reusing the romstage code.
Change-Id: I830e41b426261dd686a2701ce054fc39f296dffa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2681
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Lots of things are still placeholder and need work.
Due to the useful GPIOs being run to either the EC or the SIO1007
I have hard coded developer mode on and recovery mode off.
Change-Id: I4c308bd90db03ac5bffdfde566e5adbbaabac632
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2724
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This is the same change as made to Persimmon with
change-id I44f22:
http://review.coreboot.org/#/c/2592/
Change-Id: I5184df8deb7b5d2e15404d689c16c00493eb01aa
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2736
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same chagne as made to Persimmon in
Change-ID If8d86f:
http://review.coreboot.org/#/c/2726/
Change-Id: Id560ea85a38f73aaba2c35447bbce46bd9c0d0dd
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2741
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same change as made to Persimmon in
Change-ID If8d86f:
http://review.coreboot.org/#/c/2726/
Change-Id: Iae70c3d0af1cdaca31b206ad6daba4d38ee6b780
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2742
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same change as made to Persimmon in
Change-ID If8d86f:
http://review.coreboot.org/#/c/2726/
Change-Id: Iff594d4a3493531561eb25d1cceeb97bcefde424
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2743
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This is the same change as made to Persimmon with
change-id I44f22:
http://review.coreboot.org/#/c/2592/
Change-Id: Ie36b60973c6a5f9076bb55c8f451532711a2f8a8
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2737
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The _OSC method is used to tell the OS what capabilities
it can take control over from the firmware. This method
is described in chapter 6.2.9 of the ACPI spec v3.0.
The method takes 4 inputs (UUID, Rev ID, Input Count,
and Capabilities Buffer) and returns a Capabilites
Buffer the same size as the input Buffer. This Buffer
is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control
Dword. The OS will request control of certain
capabilities and the firmware must grant or deny control
of those features. We do not want to have control over
anything so let the OS control as much as it can.
The _OSC method is required for PCIe devices and dmesg
checks for its existence and issues an error if it is
not found.
This is the same change made to Persimmon with Change-ID
I149428:
http://review.coreboot.org/#/c/2684/
Change-Id: If6dd1a558d9c319d9a41ce63588550c8e81e595f
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2738
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The _OSC method is used to tell the OS what capabilities
it can take control over from the firmware. This method
is described in chapter 6.2.9 of the ACPI spec v3.0.
The method takes 4 inputs (UUID, Rev ID, Input Count,
and Capabilities Buffer) and returns a Capabilites
Buffer the same size as the input Buffer. This Buffer
is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control
Dword. The OS will request control of certain
capabilities and the firmware must grant or deny control
of those features. We do not want to have control over
anything so let the OS control as much as it can.
The _OSC method is required for PCIe devices and dmesg
checks for its existence and issues an error if it is
not found.
This is the same change made to Persimmon with Change-ID
I149428:
http://review.coreboot.org/#/c/2684/
Change-Id: I2701d915338294bdade2ad334b22a51db980892e
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2739
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The _OSC method is used to tell the OS what capabilities
it can take control over from the firmware. This method
is described in chapter 6.2.9 of the ACPI spec v3.0.
The method takes 4 inputs (UUID, Rev ID, Input Count,
and Capabilities Buffer) and returns a Capabilites
Buffer the same size as the input Buffer. This Buffer
is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control
Dword. The OS will request control of certain
capabilities and the firmware must grant or deny control
of those features. We do not want to have control over
anything so let the OS control as much as it can.
The _OSC method is required for PCIe devices and dmesg
checks for its existence and issues an error if it is
not found.
This is the same change made to Persimmon with Change-ID
I149428:
http://review.coreboot.org/#/c/2684/
Change-Id: Iaf7b8153cec4d730efbceae3e6957d2904b8fae4
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2740
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This is the same change as made to Persimmon with
change-id I44f22:
http://review.coreboot.org/#/c/2592/
Change-Id: I9017a7619b3b17e0e95ad0fe46d0652499289b00
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2735
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
Change-Id: If8d86f959822d528c44ab011a851659d486289b5
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2726
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The _OSC method is used to tell the OS what capabilities
it can take control over from the firmware. This method
is described in chapter 6.2.9 of the ACPI spec v3.0.
The method takes 4 inputs (UUID, Rev ID, Input Count,
and Capabilities Buffer) and returns a Capabilites
Buffer the same size as the input Buffer. This Buffer
is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control
Dword. The OS will request control of certain
capabilities and the firmware must grant or deny control
of those features. We do not want to have control over
anything so let the OS control as much as it can.
The _OSC method is required for PCIe devices and dmesg
checks for its existence and issues an error if it is
not found.
Change-Id: I1494285def7440972f0549b7cb73eb94dafc72c2
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2684
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
It's no longer required.
Change-Id: I621226a3bdfba9bc8edfd6e511a5337ae603ae19
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2723
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
The current code is attempting to convert from an invalid
starting temperature. Since we aren't sure where the temperature
will come from yet just return a static value.
This stops the kernel from going to S5 on boot because it
thinks the temperature is too high.
Change-Id: I433fa407e545458344af5842b353df5bc71bfdad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2679
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This option is not required for haswell. Enabling the option doesn't
do anything aside from complicate mtrr calculation. Therefore, remove
it.
Change-Id: I897523ff7d3606eb89961674c2eb3d384e584857
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2678
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This commit adds support for the deveveloper, recovery,
and write protect querying. It just uses jumpers on the
Basking Ridge board.
Noted ability to togggle jumpers results in toggling the
respective modes.
Change-Id: Iac189a1fa0245654591e2e9075380db422a329a0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2676
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
While looking at the Basking Ridge schematic I noticed some changes
and wanted to make sure they were reflected in the GPIO map.
Change-Id: I686653c164314ae9f68c42331d2f950751411d4a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2675
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The baskingridge has a non-zero alt_gp_smi_en value in the
devicetree.cb file. It has just to be determined which GPI
pins should trigger an SMI on basking ridge. Without this change
the board would hang during boot (presumably through a SMI flood).
No more hangs once the value is zero.
Change-Id: I9704071bb7966bd3d0bbbc4aafede3f42d829b17
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2673
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The Grays Reef CRB is deprecated by order of Intel. Basking Ridge
is the new hotness. Therefore, rename graysreef to basking ridge.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I203497e165d8efc99d3438c4c548140a6e9cc649
Reviewed-on: http://review.coreboot.org/2672
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Some of the Lynx Point ids were off. Correct those and make
the pei data BAR fields consistent with the others.
Change-Id: I4102439588362cdb94643bd1ce69c9fa4278329e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2622
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The CS5536 companion device has three different power domains.
* working domain
* standby domain
* RTC domain
When the system is "off" only the standby domain is powered.
MFGPT[7:6] are member of the standby power domain.
MFGPT7 is used to control the backlight of the device and so the
timer gets used and configured during system boot. If the system
does a reboot the timer stays configured and the Linux driver
can not use it:
"ot200-backlight: ot200-backlight.0: MFGPT 7 not availale"
The cs5535-mfgpt has a function to hard-reset all MFGPTs but the
system hangs after the first access to a MFGPT register - cause
unknown.
/*
* This is a sledgehammer that resets all MFGPT timers. This is required by
* some broken BIOSes which leave the system in an unstable state
* (TinyBIOS 0.98, for example; fixed in 0.99). It's uncertain as to
* whether or not this secret MSR can be used to release individual timers.
* Jordan tells me that he and Mitch once played w/ it, but it's unclear
* what the results of that were (and they experienced some instability).
*/
static void reset_all_timers(void)
{
uint32_t val, dummy;
/* The following undocumented bit resets the MFGPT timers */
val = 0xFF; dummy = 0;
wrmsr(MSR_MFGPT_SETUP, val, dummy);
}
After playing around with this undocumented MSR it looks like I only
need to set bit 7 to free the MFGPT7.
BTW, all MFGPT[0:5] will be reset during pll_reset().
Change-Id: I54a8d479ce495b0fc2f54db766a8d793bbb5d704
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/2527
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Even though this is under the graysreef board it really
applies to the Basking Ridge board. A subsequent patch will
rename graysreef to baskingridge.
The GPIO pins were updated to reflect the Basking Ridge schematics
as well as the DIMM spd addresses and USB over current pins.
Change-Id: Ice4e05f5203de3024cd463dfccf0bcfec1e247c1
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2632
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add a FIXME about checking a MCHBAR register that isn't setup yet.
Also, remove revision updating because I can't find anything in the
docs that suggest this is required for haswell.
Change-Id: Ia8a6e08f82e18789e31c6c2ec2c1d63740c18dc4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2631
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The intel-framework code has an updated pei_data structure.
Use the new structure and revision. Also, remove the scrambler
seed saving in CMOS since that appears to be handled in the saved
data from the reference code.
Change-Id: Ie09a0a00646ab040e8ceff922048981d055d5cd2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2630
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Grays Reef is one of Intel's CRBs for the Haswell processor. The
platform is named Shark Bay.
GPIOs were the main focus so IRQ routing and ACPI still needs to be
further looked at.
Change-Id: Ie94b7af66f772714992a92612c76ca93b9b27088
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2621
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change the OSC method to actually grant control of
PCIe capabilities to the OS instead of granting no
control. I believe the logic was backwards in the
original commit. Bits should be set when granting
control and cleared when not granting control. By
setting the return value to 0x00, we effectively
tell the OS that it cannot control any PCIe
capability. See section 6.2.9 of the ACPI spec
version 3.0 for more information.
This edit is a duplication of the OSC method that
is in the src/southbridge/intel/bd82x6x/pch.asl
file.
Change-Id: Id2462ab12203afceb9033f24d06b4dfbf2236d2e
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2714
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This enables branch prediction. We can probably find a better place
to do this, but for now we'll do it in snow's romstage main().
Change-Id: I86c7b6bc9e897a7a432c490fb96a126e81b8ce72
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2701
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Since commit »Drop redundant CHIP_NAME in mainboard.c« (a93c3fe7) [1]
`CHIP_NAME` is unneeded for mainboards as the name is composed
automatically in `src/devices/root_device.c` from the strings in
Kconfig.
Unfortunately the ports for Google Butterfly, Link and Parrot as
as well as IEI PM-LX2-800-R10 introduced CHIP_NAME again. So drop
it again too.
[1] http://review.coreboot.org/1635
Change-Id: Ice7577a2a5c6070e196f2647c440b7a8e140e27e
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2708
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Call the power_init() function. We appear to have forgotten about it
when deprecating lowlevel_init_subsystems(), but it didn't seem to
cause problems until we got to doing more interesting stuff recently.
There are some clean-ups to do from the original code, such as not
attempting to configure I2C from PMIC code, which we'll get around
to in follow-up patches.
(Credit to Gabe for spotting this)
Change-Id: I6a59379e9323277d0b61469de9abe6d651ac5bfb
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2699
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Despite everywhere the model name M5A88-V is used, in Kconfig the
string M5A88PM-V is used. Searching for that model string on the
WWW does not return anything which is unrelated to coreboot, so
change that string to M5A88-V.
Change-Id: I25cf9d4a5fc3f9b9356e8616452066ebf873f44c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2613
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: QingPei Wang <wangqingpei@gmail.com>
|
|
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This change will apply to other AMD mainboards and
will be in a different commit.
Change-Id: I44f22bc03a0dcbcd2594d4291508826cc2146860
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2592
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Changes:
- Get rid of the inagua mainboard specific code and use the
platform generic function wrapper that was added in change
http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: Id05227fcf18c6ab94ffe1beb50b533ab7b0535db
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2607
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Currently for Advansus A785E-I, ASRock E350M1 and ASUS M5A88-V
despite what is chosen in Kconfig »Chipset« menu item,
$ more .config
[…]
# CONFIG_ENABLE_IDE_COMBINED_MODE is not set
CONFIG_IDE_COMBINED_MODE=0x1
# CONFIG_SB800_SATA_IDE is not set
CONFIG_SB800_SATA_AHCI=y
# CONFIG_SB800_SATA_RAID is not set
CONFIG_SB800_SATA_MODE=0x2
[…]
the SATA controller is put into IDE mode.
$ lspci -nn | grep SATA
00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] [1002:4390] (rev 40)
Commit »sb800: Add sata ahci/raid mode kconfig option«
(d4a0e7d0) [1] added the options above to configure the mode
using Kconfig and some SB800 boards were adapted already. For
example commit »persimmon: sb800 sata mode configure update«
(1386fa74) [2] did so for AMD Persimmon.
Doing the same by assigning the Kconfig variable to the value in
`platform_cfg.h` integrates this with the three remaining boards
listed above.
The patch is successfully tested with the ASRock E350M1.
$ lspci -nn | grep SATA
00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] (rev 40)
[1] http://review.coreboot.org/225
[2] http://review.coreboot.org/227
Change-Id: I227257e2c8f04f18c27ff00fe62d42e372de67e4
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2610
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Replace »persimmon« by »board« in comment to keep `diff` output
between boards small.
Change-Id: Ieae2a63782c488ae35f22eb30f5b1049200d12c8
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2611
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Changes:
- Get rid of the union_station mainboard specific code and
use the platform generic function wrapper that was added
in change http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: I19d6b0d674b67294519383f80928471b37da1e14
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2609
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Changes:
- Get rid of the south_station mainboard specific code and
use the platform generic function wrapper that was added
in change http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: If4291d25ea81bf375f55b64c07c223a847a211d0
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2608
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is previously used exception code from libpayload.
On startup it installs and then tests an exception handler.
The test is an unaligned memory operation.
Yes, we've seen what might be exceptions in the ramstage, and
it makes sense to handle them. This code is identical in structure
and operation to the previously committed payload exception handler,
though we reserve the right to change it as circumstances require.
The remaining question is whether we need it in romstage.
Change-Id: I24484686c33c9757af8ba171ebae9773828fb69d
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2614
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
According to BKDG:
"Memory controller (MCT) and DRAM controllers (DCTs) additions:
• Support for 933 MHz (1866 MT/s) MEMCLK frequency."
Change-Id: I6f307ce3fcb355d5445f1ea86def73a41b928a57
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2589
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The Hudson-E1's default SPI speed for normal i.e. non-fast reads is 66 MHz,
but the SST 25VF032B datasheet allows max. 25. Lower the speed to 22 MHz,
otherwise BIOS flashing fails.
Change-Id: I22e87d833a3ebd316b6e873595a2480831533ab1
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2605
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Changes:
- Get rid of the persimmon mainboard specific code which has been
moved into the wrapper as a platform generic function in change
http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: I5f017dbb8dee5a09ec19734a6069ff9b71a6ab50
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2500
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
This adds some real GPIO mappings where virtual GPIOs were used before.
Change-Id: I25d4be45f986c8d622b97151f8bdae2651baf3e6
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2603
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
cosmetics
Change-Id: Iea33768d901641861aa7b2c76af8753a848f584d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2601
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
Quoting Jens Rottmann [1]:
Nevertheless I still think this whole function is bogus for the E350M1. The
function assumes GPIO21 is wired to reset APU PCIe lane 0+1 (PCIe x8, port 4+5
as Coreboot/AGESA calls it), GPIO25 resets lane 2 (PCIe x4) and GPIO02 lane 3.
But the E350M1 has PCIe x16 i.e. probably APU lanes 0-3 bundled, completely
different layout. They could have chosen GPIO21 to force resets, or 25 - or
maybe 50 like on the Persimmon or any other they fancied or - and this is the
most probable - none at all. Having BiosGnbPcieSlotReset() toggle some GPIOs
without knowing what they do on the E350M1 (if anything at all) is nonsense.
In my opinion this whole function should just "return AGESA_UNSUPPORTED" and
good riddance.
[1] http://review.coreboot.org/#/c/2445/
Change-Id: Iac66da41182e838c7e6925250cc3982adbb3e4ec
Reported-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2489
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
|
|
These are essential functions for setting up the display port and
framebuffer, and also enable such things as aux channel
communications. We do some very simple initialization in romstage,
mainly set a GPIO so that the graphics is powering up, but the complex
parts are done in the ramstage. This mirrors the way in which graphics
is done in the x86 size.
I've added a first pass at a real device, and put it in the mainboard
Kconfig, hoping for corrections. Because startup is so complex,
depending on device type, I've created a 'displayport' device that
removes some of the complexity and makes the flow *much* clearer. You
can actually follow the flow by looking at the code, which is not true
on other implementations. Since display port is perhaps the main port
used on these chips, that's a reasonable compromise. All parameters of
importance are now in the device tree.
Change-Id: I56400ec9016ecb8716ec5a5dae41fdfbfff4817a
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2570
Tested-by: build bot (Jenkins)
|
|
Since the merg of the ASRock E350M1 port (a649a96e) the compiler
warns about the following [1].
mainboard.c:35, GNU Compiler 4 (gcc), Priorität: Normal
no previous prototype for 'set_pcie_reset' [-Wmissing-prototypes]
mainboard.c:43, GNU Compiler 4 (gcc), Priorität: Normal
no previous prototype for 'set_pcie_dereset' [-Wmissing-prototypes]
Adding the function prototypes to the beginning of the file as
done in commit »Persimmon updates for AMD F14 rev C0« (d7a696d0)
addresses the warning.
[1] http://qa.coreboot.org/job/coreboot-gerrit/4975/warnings13Result/package.-139448264/file.-1544928473/
[2] http://review.coreboot.org/137
Change-Id: Iad2e62ec37c3a2f749a264974b61ac7c226e9b83
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2590
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Set up the clocks used for sound and turn on the sound clock.
Change-Id: Ic59bfa9ae87116299503e6d25aeefba98c842fb8
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2587
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
The MMC0 on google/snow can run in 8 bit mode. To simplify driver development,
we thought disabling it (using zero, which runs in 1-bit / 4-bit mode) may help.
However, after some experiments in payload drivers, setting pinmux to 8 bit mode
can still allow MMC to run in 1-bit / 4-bit mode, so it's pretty safe to enable
8 bit mode by default for better performance.
Verified to boot on google/snow, and got MMC0 working.
Change-Id: Ic0acc723fe6a8aecf373429d3801beadd70815d9
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2585
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
The first reason for selecting the CPU model at compile time was a
multi-second pause if booting a single core Fusion T40R with MAX_CPUS=2.
Recent tests show the pause has disappeared, someone must have fixed it.
The second reason was me not knowing how to make a single vgabios image
work with two different PCI IDs. Many thanks to Martin Roth for educating
me! Quote:
"The way to make coreboot use the same vbios for different video device IDs
is through the map_oprom_vendev function. In family 14 it's in
northbridge/amd/agesa/family14/amdfam14_conf.c You would name your video
bios 1002,9802 in the config and all the other device/vendor IDs for the
family 14h processors will fall through the initial check for the video
bios and will get remapped to use that vbios. This only works if you're
initializing the vbios inside coreboot. I don't know if you're using
SeaBios as a payload, but if you are you can add the vbios to cbfs as
vgaroms/vbios.rom and the rom will always be initialized."
I'd like to add the vgabios is added as type 'optionrom' when Coreboot make
adds it, however to work with SeaBios it has to be added manually with
cbfstool and with type 'raw', or it will hang.
Change-Id: I8190d0c3202a60dfccb77dde232f9ba7ce5ce318
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2584
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Commit f154c018
Author: Marc Jones <marcj303@gmail.com>
Date: Wed Dec 14 11:24:00 2011 -0700
Persimmon audio codec verb patch.
Reviewed-on: http://review.coreboot.org/490
has a typo code*c* in the comments for `AZALIA_OEM_VERB_TABLE`. As
this was copied over to the LiPPERT Fam14 boards, use the following
command to fix the typo.
$ git grep -l cocec | xargs sed -i s,cocec,codec,
Change-Id: I1525b0445edab81ab136b3adece52b78ba7abc71
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2576
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Looking at the coreboot log
[…]
PCI: 00:12.0 [1002/4397] enabled
sb800_enable() PCI: Static device PCI: 00:12.1 not found, disabling it.
sb800_enable() PCI: 00:12.2 [1002/4396] ops
PCI: 00:12.2 [1002/4396] enabled
sb800_enable() PCI: 00:13.0 [1002/4397] ops
PCI: 00:13.0 [1002/4397] enabled
sb800_enable() PCI: Static device PCI: 00:13.1 not found, disabling it.
sb800_enable() PCI: 00:13.2 [1002/4396] ops
PCI: 00:13.2 [1002/4396] enabled
[…]
and the `lspci -tnvv` output running the proprietary vendor BIOS
attached to the Wiki page of the ASRock E350M1 [1][2]
-[0000:00]-+-00.0 1022:1510
+-01.0 1002:9802
+-01.1 1002:1314
+-04.0-[01]--
+-11.0 1002:4391
+-12.0 1002:4397
+-12.2 1002:4396
+-13.0 1002:4397
+-13.2 1002:4396
[…]
both PCI devices do not exist, so remove them from `devicetree.cb`.
Commit 48918f7 [3]
Persimmon, Inagua: PCI devs 12.1, 13.1 (USB) don't exist, but 14.6 (GEC) does
did the same for AMD Inagua and AMD Persimmon.
[1] http://www.coreboot.org/ASRock_E350M1
[2] http://www.coreboot.org/File:ASRock_E350M1_info_dump.tar.bz2
[3] http://review.coreboot.org/2463
Change-Id: Ief6de1bda093d1f29d5925985e5c3839cdded537
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2536
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
If you try to reset the system with outb(3,0x92), outb(4,0xcf9) or a
triple-fault it will instead crash with a messy screen. As the more common
outb(0xFE, 0x64) doesn't work with our setup, Linux will crash whenever you
ask it to reboot. Closer inspection shows that on a warm boot of Coreboot
agesawrapper_amdinitpost() always fails with error code 7. Looks like DDR3
re-init goes wrong somehow. I tried find the reason for this but was
unable to. I am convinced this is not board specific but a bug in AGESA.
In the end I had to settle for a workaround: if amdinitpost returns 7 this
patch resets the system harder with outb(0x06, 0x0cf9), after that RAM init
will succeed. As amdinitpost is early in POST this automatic reset is
quick enough not to be noticable.
I'd perfer a real fix, but that's all I have.
Change-Id: I4763254b489f42a135232e45328ecf0d5c4d961a
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2573
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Step 2: change the Persimmon code to adapt it to the new board's hardware.
The Toucan-AF is a COM Express Compact Type 6 form factor embedded board:
- AMD Fusion G-T56N (1.65 GHz dual core) or T40R (1 GHz single core) APU
- 1-4 GB DDR3 memory down
- 1x VGA, 2x DisplayPort (1 switchable to LVDS)
- AMD A55E (Hudson-E1) southbridge
- 8x USB 2.0
- 4x SATA
- HD Audio (with codec on baseboard)
- NEC uPD78F0532 microcontroller on I2C ("SEMA")
- 7x PCIe2.0 x1 (1 on PEG)
- Intel I210 GbE (on APU PCIe x1, can be disabled for additional PCIe)
- 2x SST 25VF032B (SO8, soldered) 4 MB SPI flash (BIOS and failsafe BIOS)
The Toucan-AF has no SIO on board. This patch includes basic support for a
Winbond W83627DHG (PS/2, 2x RS232), because the ADLINK ExpressBase-6 used
for evaluation happens to have one. The code may have to be adapted to the
actual baseboard of the application.
http://www.adlinktech.com/PD/web/PD_detail.php?pid=1132
Change-Id: I9041b905bad45852ac9b402fcbd5decbc98b377b
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2572
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Step 1: copy all files unmodified from Persimmon. This makes it much
easier later to see how the two boards actually and deliberately differ
when porting bugfixes from one to the other. Git's copy detection is
imperfect (and slow).
Change-Id: I1ff02913479c07679f8c3ae5e6dd7876e6000b55
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2571
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Step 2: change the Persimmon code to adapt it to the new board's hardware.
The FrontRunner-AF is a PC/104+ form factor embedded board:
- AMD Fusion G-T56N (1.65 GHz dual core) or T40R (1 GHz single core) APU
- DDR3 SO-DIMM socket (1.5 or 1.35V)
- VGA and LVDS (via Analogix ANX3110)
- AMD A55E (Hudson-E1) southbridge
- 6x USB 2.0
- 1x SATA, 1x CFast socket
- HD Audio (via Realtek ALC886)
- PCI and ISA (via ITE IT8888)
- NEC uPD78F0532 microcontroller on I2C ("SEMA")
- Intel I210 GbE (on APU PCIe x1)
- SMSC SCH3112 SIO
- PS/2
- 2x RS232/485
- 2x SST 25VF032B (SO8, soldered) 4 MB SPI flash (BIOS and failsafe BIOS)
http://www.adlinktech.com/PD/web/PD_detail.php?pid=1131
Change-Id: Id55f89d224ad669b351c36128b12299802b721ba
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2553
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Step 1: copy all files unmodified from Persimmon. This makes it much
easier later to see how the two boards actually and deliberately differ
when porting bugfixes from one to the other. Git's copy detection is
imperfect (and slow).
Change-Id: I2fd1bf8428fc8a1e7becee888b6182b9bd8166a0
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2552
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
The SD/MMC interface on Exynos 5250 must be first configured with, GPIO, and
pinmux settings before it can be detected and used in ramstage / payload.
Verified on armv7/snow and successfully boot into ramstage.
Change-Id: I26669eaaa212ab51ca72e8b7712970639a24e5c5
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2561
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This allows to drop some special cases in romstage.c
Change-Id: I53fdfcd1bb6ec21a5280afa07a40e3f0cba11c5d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2551
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
It's not used, and not needed.
Change-Id: Ifca92f3606ac58fc26e09676488c3add5d84ae79
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2548
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
It's been on for all boards per default since several years now
and the old code path probably doesn't even work anymore. Let's
just have one consistent way of doing things.
Change-Id: I58da7fe9b89a648d9a7165d37e0e35c88c06ac7e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2547
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add two more GPIOs (total 6) as needed by the Google Snow laptop.
These are faking out settings for now. This code is tested and working.
Change-Id: I2077ffb8b85958eefdf54e19763d57cc1178ce89
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2538
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
Commit 8487229b (Persimmon doesn't have HDMI so the GNB HD Audio should be
disabled.) turned off the device in AGESA. Now remove it from
devicetree.cb, too. This prevents the following boot message:
PCI: Left over static devices:
PCI: 00:01.1
PCI: Check your devicetree.cb.
Also clarify the line's comment a bit for the Fam14 boards which still
retain this device (to counter the loss of information ;-).
Change-Id: Ib671ed2e0d04bdef2869e8d70208d6e55cdea3fd
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2537
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
The PCH register bit definition for sleep type is a little confusing.
For example, 7 is S5. To make this simpler for the mainbaord developer,
the mainboard smi sleep hander is called as mainboard_sleep(slp_typ-2).
A couple mainboard SMI handlers were using the PCH define for slp_ty,
so S3 code would be run for S5 and S5 code would never be run.
Change-Id: Iaecf96bfd48cf00153600cd119760364fbdfc29e
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2514
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Mainly replace spaces by tabs and format comments correctly.
Commit »Inagua: Indent and wihtespace cleanup« (f03360f3) [1] was
unfortunately incomplete and also used spaces instead of tabs in
some cases.
Hopefully fix this once and for all to have a template for the
other boards.
[1] http://review.coreboot.org/547
Change-Id: If15c797581dfefe2a57cd6f26e5bdac4cdd014dd
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2526
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch reduces unnecessary differences between AMD Inagua, Persimmon,
Union Station, South Station and Asrock E350M1. It's only cosmetical, but
makes them a little bit easier to compare.
This is the remainder of the original http://review.coreboot.org/2464,
parts of which somehow got lost in a flurry of refactoring and splitting
patches.
Change-Id: I034228be9edaaa4122506763d7bb4158f8e0ec53
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2529
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Changes:
- Fix printk warnings for these two platforms by getting rid of the
l length specifier and casting to unsigned int.
This gets rid of a bunch of warnings like this one:
agesawrapper.c:279, GNU Compiler 4 (gcc), Priority: Normal
format '%lu' expects argument of type 'long unsigned int',
but argument 3 has type 'UINT32' [-Wformat]
Notes:
- This is the same change that was done for Tyan s8226 in change:
ddff32eb - http://review.coreboot.org/#/c/2451/
Tyan S8226: Fix printk warnings
- I have not tested this change on either of these platforms, I have
just compiled it.
Change-Id: I46b4c13fde7473cd2a084c7c7cb5c893f1731b02
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2502
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Changes:
- Add #include of delay.h in mainboard.c to pick up declaration of
mdelay function.
Notes:
- This fixes this warning:
mainboard.c:69, GNU Compiler 4 (gcc), Priority: Normal
implicit declaration of function 'mdelay' [-Wimplicit-function-declaration]
Change-Id: I72f333cd87215a7fc1e62d1d7ee4b2395444b03e
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2501
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Currently on for example on AMD Persimmon and ASRock E350M1 Linux
complains, that the PBLK length is invalid [1].
ACPI: Invalid PBLK length [0]
Consequently, frequency scaling might not work correctly, though for
these two boards it seems to work according to PowerTOP.
Indeed, according to the ACPI specification [2], setting PBlockLength
to 0 is only allowed if there is no PBlockAddress. Otherwise it has to
be set to 6.
18.5.93 Processor (Declare Processor)
[…]
PBlockAddress provides the system I/O address for the processors
register block. Each processor can supply a different such
address. PBlockLength is the length of the processor register
block, in bytes and is either 0 (for no P_BLK) or 6. With one
exception, all processors are required to have the same
PBlockLength. The exception is that the boot processor can have
a non-zero PBlockLength when all other processors have a zero
PBlockLength. It is valid for every processor to have a
PBlockLength of 0.
And that is exactly what Linux is checking in
`drivers/acpi/processor_driver.c` [3].
static int acpi_processor_get_info(struct acpi_device *device)
{
[…]
/*
* On some boxes several processors use the same processor bus id.
* But they are located in different scope. For example:
* \_SB.SCK0.CPU0
* \_SB.SCK1.CPU0
* Rename the processor device bus id. And the new bus id will be
* generated as the following format:
* CPU+CPU ID.
*/
sprintf(acpi_device_bid(device), "CPU%X", pr->id);
ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Processor [%d:%d]\n", pr->id,
pr->acpi_id));
if (!object.processor.pblk_address)
ACPI_DEBUG_PRINT((ACPI_DB_INFO, "No PBLK (NULL address)\n"));
else if (object.processor.pblk_length != 6)
printk(KERN_ERR PREFIX "Invalid PBLK length [%d]\n",
object.processor.pblk_length);
else {
pr->throttling.address = object.processor.pblk_address;
pr->throttling.duty_offset = acpi_gbl_FADT.duty_offset;
pr->throttling.duty_width = acpi_gbl_FADT.duty_width;
pr->pblk = object.processor.pblk_address;
/*
* We don't care about error returns - we just try to mark
* these reserved so that nobody else is confused into thinking
* that this region might be unused..
*
* (In particular, allocating the IO range for Cardbus)
*/
request_region(pr->throttling.address, 6, "ACPI CPU throttle");
}
[…]
}
This issue has proliferated to all AMD based boards so fix it for
all of them by setting P_BLK length to 6.
The DSDT of for example AMD Parmer and AMD Thatcher also set it
to 6 everywhere so this solution is taken instead of setting the
P_BLK system I/O base to 0 for all but the first processor which
is how it is done for earlier AMD based boards.
As note having to set this manually should not be needed and
this should be autogenerated as done for most of the Intel boards
and the AMD K8 based boards (`src/cpu/amd/model_fxx/powernow_acpi.c`).
[1] http://www.coreboot.org/pipermail/coreboot/2013-January/073636.html
[2] http://acpi.info/DOWNLOADS/ACPIspec40a.pdf
[3] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=blob;f=drivers/acpi/processor_driver.c;h=e83311bf1ebdaaaea1adbf2de1351cca907d3465;hb=5da1f88b8b727dc3a66c52d4513e871be6d43d19#l351
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
• ASRock E350M1:
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
• AMD Persimmon:
Tested-by: Martin Roth <martin.roth@se-eng.com>
Change-Id: Ie79fe4812532d124cc81747c75a4f3d88d00531c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2189
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
USB ports 0-4 are handled by PCI devices 12.0 (OHCI) and 12.2 (EHCI). 12.1
simply does not exist, so remove it from devicetree.cb. While at it make the
comment more detailed. Likewise for all USB ports.
USB device 14.6 is the Broadcom GbE MAC integrated in the Hudson-E1. Add it
to devicetree.cb. It's used on Inagua (on), but not on Persimmon (off).
Change-Id: Idea27b3390fa4470f2592e79fdd633d5a218b97b
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2463
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
|
|
The DSDT header contains the fields OEMID and OEM Table ID. See
for example ACPI specification 4.0a [1]
5.2.11.1 Differentiated System Description Table (DSDT)
on page 135. There Table 5-16 contains the descriptions.
Field Byte Length Byte Offset Description
===================================================
OEMID 6 10 OEM ID
OEM Table ID 8 16 The manufacture model ID.
Currently in coreboot there is no common method what to put in
these fields.
Mostly Intel based boards populate it with "CORE " ore "COREv4"
and AMD based boards populate it with the board vendor and
model number, abbreviated appropriately to fit into these fields.
On most boards the proprietary vendor BIOS seems to leave these
fields – displayed with `sudo dmidecode` under System Information –
blank
To Be Filled By O.E.M.
and fill out the Base Board Information with the board vendor and
model name.
In [2] Jens Rottmann argues that the this is really just the table
ID used for naming it and that »99% of the DSDT code is not board
specific«.
Both approaches seem to have their advantages, but using the
second one, developers often seem to forget to update them (for
example AMD Thather).
The current situation is at least not optimal. and therefore at
least unify the string in the OEM Table ID. If unifying the
OEM ID is also a good idea this should be done too.
If later on it should be decided that the board vendor and model
should be used again, this should be somehow derived from
Kconfig.
The following command was used for the change [3].
$ git grep -l '\/\* TABLE ID \*\/' | xargs sed -i '/TABLE ID/s/"\([^"]*\)"/"COREBOOT"/'
This patch is split out from [2].
[1] http://www.acpi.info/spec40a.htm
[2] http://review.coreboot.org/#/c/2464/
[3] http://stackoverflow.com/questions/5207838/sed-regex-matching-text-between-to-double-quotes-when-a-certain-text-appears-i
Change-Id: Iec98c615ce37f928abc1b500eff5aa865d772cb2
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2472
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
These were not separable or it would have been two CLs.
Enable CHROMEOS configure option on snow. Write gpio support code for
the mainboard. Right now the GPIO just returns hard-wired values for
"virtual" GPIOs.
Add a chromeos.c file for snow, needed to build.
This is tested and creates gpio table entries that our hardware can use.
Lots still missing but we can now start to fill in the blanks, since
we have enabled CHROMEOS for this board. We are getting further into
the process of actually booting a real kernel.
Change-Id: I5fdc68b0b76f9b2172271e991e11bef16f5adb27
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2467
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Similar to the discussion on the coreboot list [1]
Am Freitag, den 22.02.2013, 02:17 +0100 schrieb Peter Stuge:
[…]
> Function names should try to be descriptive. "enable_dev" is not very
> descriptive. I like "mainboard_enable" because it makes output such
> as
>
> printk("%s: foo", __func__);
>
> useful.
rename the function for the northbridge to `northbridge_enable`.
[1] http://www.coreboot.org/pipermail/coreboot/2013-February/074549.html
Change-Id: I262311ec511e394550330214621b8c37780c1d4e
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2496
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
- Fix redefinition warning for SB_GPIO_REG50 introduced in commit
fa8702cf - http://review.coreboot.org/#/c/2446/
Persimmon: adapt PCIe reset code copied from Inagua to actually
match Persimmon
The warning being fixed is:
SB800.h:1491, GNU Compiler 4 (gcc), Priority: Normal
"SB_GPIO_REG50" redefined [enabled by default]
- Enable warnings as errors so no more warnings will be accidentally
committed.
Change-Id: Ib443b2bd2067f0b7d5f93f79170899a0f8f61060
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2494
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
To reduce the differences between these file name the enabling
device function in the directory `src/mainboard` uniformly
`mainboard_enable` [1].
Thanks to the awesome help of gnomon and BlastHardcheese in the
IRC channel #sed on <irc.freenode.net>. gnomon came up with the
following command to do the actual work.
$ cd src/mainboard
$ for f in */*/mainboard.c ; \
> do src="$(awk '/\.enable_dev = /{v=$NF; sub(/,$/,"",v); print v}' "$f")" ; \
> [[ -z $src ]] && continue ; \
> printf '%s\n' "g/${src}/s/${src}\([,(]\)/mainboard_enable\1/p" w | ed -s "$f" ; \
> done
`src/mainboard/digitallogic/msm586seg/mainboard.c` and
`src/mainboard/technologic/ts5300/mainboard.c` had to be adapted
manually as no comma was used separating the struct members.
And with the following statement, gnomon is even more likable!
My pleasure entirely. Good luck with coreboot; I'm a big fan of the project.
[1] http://www.coreboot.org/pipermail/coreboot/2013-February/074548.html
Change-Id: Ife9cd0c2d9cc1ed14afc6d40063450553f06a6c6
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2493
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is coreboot’s coding style.
Change-Id: I7441f2c1927a49a3b7171112b7798dae6b56cfb5
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2492
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Bernhard Urban <lewurm@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is the common way to name that function, so unify that.
Change-Id: I8a01051bd304039662894b89eed53ce14dde98b6
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2491
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Ladies and gentlemen, I'm very happy to announce coreboot support for
the latest and greatest Google Chromebook: The Chromebook Pixel.
See the link below for more information on the Chromebook Pixel, and
its exciting specs:
http://www.google.com/intl/en/chrome/devices/chromebooks.html#pixel
The device is running coreboot and open source firmware on the EC
(see ChromeEC commit for more information on that exciting topic)
Change-Id: I03d00cf391bbb1a32f330793fe9058493e088571
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2482
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
`_PLATFORM_CFG_H_`
Reduce unnecessary differences between AMD based boards only
using the file `platform_cfg.h` for configuration making them
a little bit easier to compare.
Inagua & co. mention the board name in several places which are really not
that board specific. Sometimes people even forget to change it:
Union Station’s platform_cfg.h starts with "#ifndef _PERSIMMON_CFG_H_".
Funny. Change that to "_PLATFORM_CFG_H_" everywhere.
The following command was used.
$ find . -name platform_cfg.h | xargs sed -i '/_CFG_H_/s/_.*_/_PLATFORM_CFG_H_/'
More boards seem to use that kind of naming (`git grep _CFG_H_`)
but it is not certain that this will not break anything as for
example the board AMD Dinar also has header files for
configuration stuff for the north- and southbridge.
$ git grep _CFG_H_
[…]
src/mainboard/amd/dinar/platform_cfg.h:#ifndef _PLATFORM_CFG_H_
src/mainboard/amd/dinar/platform_cfg.h:#define _PLATFORM_CFG_H_
src/mainboard/amd/dinar/platform_cfg.h:#endif //_PLATFORM_CFG_H_
src/mainboard/amd/dinar/rd890_cfg.h:#ifndef _RD890_CFG_H_
src/mainboard/amd/dinar/rd890_cfg.h:#define _RD890_CFG_H_
src/mainboard/amd/dinar/rd890_cfg.h:#endif //_RD890_CFG_H_
src/mainboard/amd/dinar/sb700_cfg.h:#ifndef _SB700_CFG_H_
src/mainboard/amd/dinar/sb700_cfg.h:#define _SB700_CFG_H_
src/mainboard/amd/dinar/sb700_cfg.h:#endif //_SB700_CFG_H
[…]
Change-Id: Ida15fa6a7adfc770240ac30e795946000dae3f16
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2464
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
At the request of Paul Menzel, I reran an
old classic of a coccinelle script:
@@
expression E;
@@
-(E + 7) & -8
+ALIGN(E, 8)
@@
expression E;
@@
-(E + 15) & -16
+ALIGN(E, 16)
Change-Id: I01da31b241585e361380f75aacf3deddb13d11c3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2487
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
There were just whitespace differences and three boards did not
contain
printk(BIOS_DEBUG, "alib\n");
dump_mem(ssdt, ((void *)alib) + alib->length);
which is enclosed `#if DUMP_ACPI_TABLES == 1` to dump the ACPI
tables.
Basically the whitespace in the license header in Inagua’s file
was fixed and then the file copied over to the other directories.
Change-Id: I23f73acad427b5ec14cf51651af67240871f7488
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2470
Tested-by: build bot (Jenkins)
Reviewed-by: Alvaro G. <andor@pierdelacabeza.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
