| Age | Commit message (Collapse) | Author |
|---|
|
Enable CRFP power control in gpio table. RST needs to drive low
before PWR enable. Since reset signal is asserted in bootblock,
it results in FPMCU not working after a S3 resume. This is a known issue.
BUG=b:181377402
BRANCH=None
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I8a8fae80c3cc186e0a097ab2007abb656f382cbd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52185
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allows using the internal speakers of the oryp5.
Smart AMP data was collected using a logic analyzer connected to the IC
during system start on proprietary firmware. This data is then used to
generate a C file [1].
[1]: https://github.com/system76/smart-amp
Change-Id: I148f18ff3e754d913bdf907121b103c6de02ffc3
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47962
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add LTE modem to devicetree
Configure GPIO control for LTE modem
BUG=b:178092096
TEST=Built image and verified with command modem status
Change-Id: Id8f483e1132a08500fbe950711cc84197ce40b12
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=b:185084331
BRANCH=dedede
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede coreboot-private-files-baseboard-dedede coreboot chromeos-bootimage.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Ie982741cb7b328623cf27f41c31f819e8cdb7bc9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The new discovery from Google & AMD, the value currently used
STAPM Time Constant of 1640 is reducing real PPT TSP from the
target 4.8W to 4.68W.
Furthermore, when using the "default" STAPM Time Constant of 1400,
the actual real PPT TSP becomes 4.89W.
Operating at this default settings therefore uses a higher real PPT TSP,
which results in a significant performance improvement.
BUG=b:175364713,b:184902568
BRANCH=zork
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test => pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I9cf4d51f42fe250340bcb642db07796c9a480c34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52312
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The new discovery from Google & AMD, the value currently used
STAPM Time Constant of 1640 is reducing real PPT TSP from the
target 4.8W to 4.68W.
Furthermore, when using the "default" STAPM Time Constant of 1400,
the actual real PPT TSP becomes 4.89W.
Operating at this default settings therefore uses a higher real PPT TSP,
which results in a significant performance improvement.
BUG=b:184902568
BRANCH=zork
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test => pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I102c1c5f8215a6c5f7a4451f5731167c32e27c90
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52313
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add wifi sar for botenflex.
Due to fw-config cannot distinguish between boten and botenflex.
Using sku_id to decide to load botenflex custom wifi sar.
Detail reason for using sku_id in b:182433707.
BUG=b:182433707
TEST=build and test on boten/botenflex
Cq-Depend: chrome-internal:3686313
Change-Id: Id3f2529a7ad56ff306df98f77cda556656da52a5
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update device tree override to match schematics.
BUG=b:182227204
TEST=emerge-volteer coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Ib1698504cc0b377659fa60b4fae25227b5823753
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Add support for gpio driver for collis
BUG=b:182227204
TEST=emerge-volteer coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Ief225093bf93137384b64327a1c66576c9a5193a
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Tested with TianoCore payload (UefiPayloadPkg).
Working:
- PS/2 keyboard, touchpad
- Both DIMM slots
- NVMe port
- SATA port
- SD card slot
- Left USB 3 Type-A port
- Right USB 3 Type-A port
- Right USB 3 Type-C port
- Webcam
- Ethernet
- Integrated graphics using Intel GOP driver
- mDP output
- HDMI output
- Internal microphone
- Internal speakers
- 3.5mm audio input
- 3.5mm audio output
- S3 suspend/resume
- Flashing with flashrom
- Booting to Ubuntu Linux 20.10 and Windows 10
Not tested:
- Thunderbolt functionality
Change-Id: I5c992e603dbd57ae1b4ddc3a0f9bfc92d6acc813
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The first CSE Lite SKU is available, therefore enable the Kconfig
option to have the CSE reboot the system into its RW FW during a cold
boot.
BUG=b:183826781
TEST=50 cold reboot cycles
Cq-Depend: chrome-internal:3758108
Change-Id: Ib3a1a9f8ac51bdab8858b2764d5bc0f6f07987cc
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The CACHE_MRC_SETTINGS option is already selected in SoC Kconfig.
BUG = N/A
TEST = Build and boot Portwell M107
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Change-Id: I528c582419fb2044f5edfd7a070785489efdf7a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52154
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Lillipup add two sku for OLED panel.
Additional VBT is necessary to modify PWM source from VESA eDP AUX
interface
BUG=b:183630802
TEST=emerge-volteer coreboot-private-files-baseboard-volteer
check vbt_oled.bin is under build folder and check in CPU log.
Cq-Depend: chrome-internal:3744227
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I576297b8296def3c37a01ae0223fa332aa9f02b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52150
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=boot from SPI-NOR and UART works fine.
Change-Id: I279b3d2da8a30b38686005212f6c019a9a646874
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Port 80 (actually 0x80-0x8f) is a fixed I/O range and thus does not have
to be set up as generic range. Drop the entry from clevo/cml-u, which
has been forgotten in commit c5f1dc9.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I05844db4cfe96e6075bd6526ffc242973a2082c2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
With DDR4, CA Vref goes to channel 0, and CH1 Vref goes to channel 1.
Change-Id: I64606824b4f82affb0fcfc78e68ba29859a1cc69
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52110
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
DPTF HIDs are different per-platform going forward, so refactor these
into SoC-specific structures which the DPTF driver can query at runtime
for platform-specific information.
Change-Id: I6307f9d28f4274b851323ad69180ff4ae35053da
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ief59bdea392ab3f141ccf7444c608aef99701d2e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Port 80 (actually 0x80-0x8f) is a fixed I/O range and thus does not have
to be set up as generic range. Drop the entries from the devicetrees.
Change-Id: I8a54d3c35a321a2d57bd846662f7339eff53e5a8
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
TEST=Timeless build results in identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie39dc99bef4eb3776388d7406239bac6031bfaaf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Sync from guybrush.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ica4e6511a5106a958567565b96d5888b8c829ff2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
use PicassoGenericVbios.bin as default instead of raven VBIOS for
Bilby.
Change-Id: I99621173a33a1154f8bb4929d199288265bbe04d
Signed-off-by: Ritul Guru <ritul.bits@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52209
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit enables HECI such that interface can be used from
userspace on the dedede mainboards.
BUG=b:184219504
TEST=Build and flash drawcia, verify that Intel Flash Programming Tool
can communicate with the Converged Security Engine.
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: I5b28c471d6554a5e14538073d48ef47da05936fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
To update the sx9324 registers after RF team fine-tuned the parameters.
BUG=b:172397658
BRANCH=firmware-zork-13434.B
TEST=build coreboot and verify the sx9324 function
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Ief85bc61952144a1d7a151100d89938517078ab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51936
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The logic for bytes to copy to the function input pointer was wrong.
What it did was to loop over all 2 bytes that need to be read and only
copy the first byte.
Change-Id: Ic08cf01d800babd4a9176dfb2337411b789040f3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
The patch enables Bluetooth config in the devicetree and removes
non-existent Bluetooth PCI interface.
TEST=Verified by checking Garfield Peak controller's PID:VID(8087:0033) in
the lsusb ouput.
Output of lsusb:
Bus 004 Device 003: ID 0bda:8153 Realtek Semiconductor Corp. USB 10/100/1000 LAN
Bus 004 Device 002: ID 0bda:0411 Realtek Semiconductor Corp. 4-Port USB 3.0 Hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 003: ID 0781:55a9 SanDisk Corp. Dual Drive
Bus 003 Device 004: ID 413c:2113 Dell Computer Corp. Dell KB216 Wired Keyboard
Bus 003 Device 002: ID 0bda:5411 Realtek Semiconductor Corp. 4-Port USB 2.0 Hub
Bus 003 Device 005: ID 8087:0033 Intel Corp.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I7a54d344ef1b0418bee56e7308977a61604b954a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52182
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To enable WWAN we want to release it from reset start.
BUG=b:180166408
TEST=WWAN enumerates on brya
Change-Id: I4f9884d3b2fc8822dda1a6fe743c863aa6c696da
Signed-off-by: Alex Levin <levinale@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52199
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4d949d252ca24ebd4e4ed9c7dd17ede3810a8bfd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The patch enables HECI1 interface to allow OS applications to communicate
with CSE.
BUG=None
TEST=Build and boot ADLRVP. Run lspci and check pcie device (00:16.0)
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I34ff842481bdfc7933a76555ff0fd70f4fbbb9a7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
Enable I2C2 in devicetree and fill ACPI information for Codec.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib75ef99cbca8b2f38268705704e7616b456f19d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
Configure the BT disable GPIO to logic low in order to enable Bluetooth.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I7661dea682cbe0ae5e169d87e794ed6ed3c83b5e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ie3917c10ecf37c914dbadce5949b8f4f772abd5c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I29be8572bc7bb366347eabe553be49775dec46a8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I483c2e77eedcb434709b67bf9b3fbca636499508
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
Enable Acoustic noise mitigation for boten and set slew rate to 1/8
which is calibrated value for the board.
BUG=b:180668001
BRANCH=dedede
TEST=build firmware to UPD and Acoustic noise test
Change-Id: I75851bd7c279feeab4ab94f4c82d55bf0e5ce316
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Rename the Kconfig parameter to more accurately reflect what it does.
TPM can be initialised in a different stage too, for instance with
VBOOT it is done in verstage.
Change-Id: Ic0126b356e8430c04c7c9fd46d4e20022a648738
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Use VPD variable "fsp_dimm_freq" to select DDR frequency limit.
Tested=On OCP Delta Lake, DDR frequency limit can be changed via VPD.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I1232feae5090420d8fa42596b46f2d4dcaf9d635
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
The intel/soc/broadwell smihandler has no handler for this APM call.
Change-Id: I2bcec7cce00d433a197a9e2fb01434a2998e1452
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52167
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure unused GPIOs as NC
BUG=b:180830117
TEST=Build and boot lindar to OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I0ba51dc262ccbf22b45d3be4b65e006f92587fd8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Some eMMCs need 80+ms for CMD1 to complete. And the payload may need to
access eMMC in the very early stage (for example, Depthcharge needs it
20ms after started) so we have to start initialization in coreboot.
On Hayato Chromebook this can save ~100ms in total.
BUG=b:177389446
TEST=emerge-asurada coreboot
BRANCH=asurada
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: I2f58d203e969dc1a13a479d7dc63b1b162a9ae3f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51973
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select mmc storage config for asurada.
Build MTK host mmc driver.
BUG=b:177389446
TEST=emerge-asurada coreboot
BRANCH=asurada
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: Iac656d57c2b834d1ce393fd991275b897e597b4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
selecting SOC_AMD_COMMON_BLOCK_USE_ESPI will disable the lpc decodes,
so not selecting that keeps the lpc decodes.
Change-Id: I03a8d4b804cee205b9e06b00e2e5a442452f8f86
Signed-off-by: Ritul Guru <ritul.bits@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52016
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These changes involve NVMe specific GPIO programming to enable pcie
NVMe SSD boot. Add nvme dev,func in devicetree and also remove
unused GPIOs programmed in Bilby.
Change-Id: I4407f82122c04b13684d4176ba5cd5a9fe03f0db
Signed-off-by: Ritul Guru <ritul.bits@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51674
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When GPIO_2 was configured as PAD_NF with the WAKE_L function selected
the GPIO_2 override in soc_gpio_hook called soc_route_sci that wrote the
corresponding SCI mapping register, but didn't set up the SCI level and
trigger type, so that couldn't have worked on most of the boards. The
only boards where I think this was actually tested are the google/zork
ones and they configured GPIO_2 as PAD_SCI where the GPIO mux setting is
GPIO mode instead of the WAKE_L mode, but at least the SCI was
configured correctly. The new PAD_NF_SCI macro can configure both the
right GPIO mux setting and set up the SCI configuration correctly, so
use this new macro for the GPIO_2 pin. For test purposes I also added
the corresponding GPIO_2 configuration to amd/mandolin to see if the
affected registers end up having the expected value using the HDT
debugger to look at the registers, but didn't test the wake-up
functionality, since S3 resume isn't working on amd/mandolin yet.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Change-Id: Ic069e46b759fb6746645faccd254263c49a892d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51756
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The CACHE_MRC_SETTINGS option is already selected in SoC Kconfig.
BUG = N/A
TEST = Build and boot facebook FBG1701
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Change-Id: I1c7fd5ec36726724939660bf506a45a44848f8c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52152
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Update the ACPI name from AMDP1015 to 1002105 based on b/177971830#180.
AMDI1015 -> AMD platform with RT1015
10021015 -> AMD platform with RT1015p
Reference:
https://www.spinics.net/lists/alsa-devel/msg124694.html
BUG=b:177971830
BRANCH=firmware-zork-13434.B
TEST=emerge-zork coreboot chromeos-bootimage, then verify with ALC1015 AMP
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Id8f378ad6f3328d7db949ecdb609a2f16acd3884
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52127
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PS/2 keyboard used IRQ 1.
BUG=none
TEST=Boot guybrush and see internal keyboard working
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I97b7382eac28aae2cc82f430c58cf8066b9701e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52143
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Guybrush doesn't have a PS/2 mouse.
BUG=none
TEST=boot guybrush to the OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I87e51d23b69cfd6ad7bb88b364714d679e92728f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52145
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To train PCIe devices, the devices need to be enabled and taken out of
reset. This patch does the bare minimum needed to train PCIe. It is
not intended to handle timings, which will be addressed later.
Copy the enables for WWAN & WLAN into early GPIO Init so that they're
enabled before FSP-M runs and trains the PCIe busses.
Again, this patch is the minimum to let the FSP train the PCIe busses.
BUG=b:182202136
TEST=Boot guybrush from NVME.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I3807e02de1e9ae40b0a4162217afd6aabb5b04ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52115
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This option's value is not used anywhere. Remove it.
Change-Id: I0f30cddd30d459f48b51f377b111bbc04709c5f8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
It is zero for all mainboards. If one really wanted to ignore VT-d
support, a user-visible Kconfig option would be a better approach.
Change-Id: I320c10317f3fabee5443c16ebdf1ffd0e24193b8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
WFC Camera driver will control the power sequence.
Therefore, set default to low.
BUG=b:184024459
TEST=abuilds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I7ce25b83a715a022e36289dc0abf0d39f5798eb0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update devicetree and gpio setting of metaknight to handle pen detection.
BUG=b:180426949
TEST=Build and check behavior is expected.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ieeca20eff57b16217a13d996dca3f662911f3e5a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This is a temporary workaround for a bug that breaks graphics due to
some power management issue.
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie4c8ff8e827901112fd8b2e993898006bc133241
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52141
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
pcie_rst isn't working correctly, so use the AUX resets to reset the
PCIe devices before training.
BUG=b:182202136
TEST=See PCIe devices train & enumerate
Change-Id: I6db21c79dcbd40c7a8c3f01c60b02882a3851278
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
TEST=Worked on Matt's Majolica board.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Change-Id: I65c7e0ebf1e43fd4608d46bae8a176cfc3d0236b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51956
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I838aeda2e6c403eaa3388a6b934e7ab6b4e918e3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52045
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Change-Id: Ic8a4349315f8759c79dc6b087b2a933c307cd573
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This patch adds the functionality to write the DXIO and DDI descriptors
to the UPD data structure to the SoC code and adds the
mainboard_get_dxio_ddi_descriptors function to each mainboard using the
Cezanne SoC that gets called to get the descriptors from the board code.
Change-Id: I1cb36addcf0202cd56ce99e610a13d6d230bc981
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51948
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I375ad38da14189de2ae2713082a80e8cdb2fe5f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Id6c20b32ddafe415132ce70abf5381ff3aad13f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I850a3ecc8776593d97f4162e812a39991caa30ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
GPIOs should be configured in ramstage even if they are configured in an
earlier stage.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I07d5c46d6ea6dc2bc9ab265d0c01772d653884cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I2d4ec1556ac7136c454eb025ff99aafbf49b8982
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I1d28c2335b095a77285dcb261a0dffe96d129c46
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I9768feaadf2423acd50a71e9a2310b4ab2d1a2a8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Following commit de50d39, remove the `volume` entry from cmos.default.
Change-Id: Ieebafffa0d2fbf6cdd24cff4ddefe090a727cbfa
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
On VCCin there was an oscillation which occurred just as the kernel
started (kernel starting... message). On some devices, this behavior
seems even worse. In previous platforms VCCin toggled for a few ms
and then was stable. For volteer, this happens at the same point in
time for around 40ms. However, it starts oscillating again later in
the boot sequence. Once at the root shell, it seems to oscillate
indefinitely at around 100-200Hz (very variable though). To fix this
we need to control the deep C-state voltage slew rate.We have options
for controlling the deep C-state voltage slew rate through FSP UPDs.
This patch expose the following FSP UPD interface into coreboot:
- AcousticNoiseMitigation
- FastPkgCRampDisable
- SlowSlewRate
We are setting SlowSlewRate for all volteer boards to 2 which is Fast/8.
TGL has a single VR domain(Vccin). Hence, the chip config is updated to
allow mainboards to set a single value instead of an array and FSP UPDs
are accordingly set.
BUG=b:153015585
BRANCH=firmware-volteer-13672.B
TEST= Measure the change in noise level by changing the UPD values.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: Ica7f1f29995df33bdebb1fd55169cdb36f329ff8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit 52e61945588bc327844acc4658426861d63ad189.
Reason for revert: Graphics actually works now. I should have abandoned this CL.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I83aac3a2c616bb434706f23e36549760bc764080
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
TPM_INIT is disabled by default. This prevents TPM to be operational
when VBOOT is disabled.
Remove the TPM_INIT disable.
BUG=N/A
TEST=tested on facebook monolith with VBOOT disabled.
Change-Id: I84d525a18c84643903922fef0a11dcf98abbbe4d
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52052
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Make sure the standard for the board options are set when VBOOT is
enabled.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: I9749eeeffbd26e7c5caaeb7c0407a765cf093337
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
1. Follow GT7375P Programming Guide_Rev.0.6 to increase
reset delay to 180ms.
BUG=b:181711141
TEST=Build and boot lindar to OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I82222ca094eead7e9e691857e128243cfe7c310e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51739
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable Bayhub SD card reader power-saving mode for Lindar and Lillipup.
BUG=b:173676531
TEST=Boot to OS and test with SD card function.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I923d6e1beacd007c0e501f39c1f434c3e1085b9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This changes updates the iDisp-Link T-mode to 8T required for ADL-M.
The update is made because the HW on ADL now supports 8T mode.
BUG=None
TEST= build and boot ADL-M RVP and verify HDMI/DP audio playback.
Signed-off-by: Francois Toguo <francois.toguo.fotso@intel.com>
Change-Id: I9d0bf7dc76348f7e184e8496f042badc30bf3211
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51353
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Configure Power Enable, Reset and Clock GPIO for both camera
2. Use same ASL code as ADL-P RVP
Configure RST, PWR_EN and IMGCLKOUT signals for WFC and UFC
TEST=Build, Boot and Verify streaming in both Camera
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I70636eaa8d9bdf23d649e811b3ff4f33b1bc604e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50265
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Config ANX7625 line data end same time on all line.
BUG=b:173603645
BRANCH=kukui
TEST=Display is normal on Kukui
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Change-Id: Ia1dc217138a98a79ef2f31225b52ba2b1aaf8672
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Just do it already.
The two SCSI-specific options for p2b-{ls,ds} will be wired up in a
followup. They will be ignored by boards without the hardware.
Change-Id: Ia43d502219d7c23d21f49d651113e3d653c6e9f4
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This is locking up the OS. For now this will unblock booting.
BUG=b:183971103
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Id2b96eedf38c9038169407418c6d36f13299fb62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
Add LTE module support into devicetree and associated GPIO configuration.
BUG=b:183774169
BRANCH=dedede
TEST=Build the cret board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I14684bb30e46bf845a401649f56b16b60db379e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Select the drivers for DA7219 codec and MAX98360A spk amp
BUG=b:183771323
BRANCH=dedede
TEST=emerge-dedede coreboot chromeos-bootimage
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I3fd7c374fc8214e25a28fb9ba62a9c8473d3f755
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51841
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The define for color keyboard setting has never been used, as it was
added as a Kconfig selection when ec/system76/ec was introduced.
Change-Id: Iec9134e226382d32783342ef1d37c6f6f6caeb6e
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
The define for color keyboard setting has never been used, as it was
added as a Kconfig selection when ec/system76/ec was introduced.
Change-Id: I6c8f17b398fb4645feb830c2ad28ac98fb744280
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
The define for color keyboard setting has never been used, as it was
added as a Kconfig selection when ec/system76/ec was introduced.
Change-Id: Ib83d4510c14ddf083660e42175ab093403792cac
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Current get panel_id is over sku_id() >> 4, but sku_id is combined with
wfc_id/lcm_id/sku_id, so the panel_id value is wfc_id << 4 | lcm_id()
in fact. When wfc_id is not 0, the panel_id will be wrong. So only get
the low 4 bits for the panel_id.
BUG=b:183779755
BRANCH=kukui
TEST=emerge-kukui
Change-Id: I63e0c8a2719462a9b979afe52a27c78b9fc804e8
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The EDID and initial code are provided by STA (the vendor).
BUG=b:183969078
TEST=Boots on Chromebook Katsu and displayed developer firmware screen
successfully.
Signed-off-by: Sunway <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I54e72c072b47d2be264ed7f0700812a6c704a104
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51918
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All known on-chip PCI devices are disabled in the chipset devicetree.
So they are removed from the mainboard devicetree.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: Ie67cd8afc9ea92e9fd7caed4338cb25a68d94cb1
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
The romstage does not fit in RO_SECTION.
Increase the CBFS size in RO_SECTION.
BUG = N/A
TEST = Boot Facebook FBG1701 with VBOOT enabled.
Change-Id: I2f1020acb3ec99d4cddbaa05b0998fe32b470d3e
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Replace the mainboard-specific code for "POST complete" signalling with
devicetree entries for using the newly introduced IPMI driver
functionality.
Test: Boot the machine via the BMC web interface and check that sensors
get read correctly by the IPMI firmware when the payload starts.
Change-Id: I7503dec4e72810db8dfe74f72638b466a3d66748
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48671
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On OCP Tioga Pass the pad GPP_B20 is used as output for signalling "POST
complete" to the BMC. According to the schematics and the code in
`ramstage.c`, the signal is active-low. There is an external pull-up
resistor.
To make the signalling work as it should, set the initial output value
to `high`.
Change-Id: I82fbda1caba9163ba3b2e38f494a0cefa27e657f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48670
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch includes changes to add Cr50 support over GSPI0.
BUG=b:175579964
TEST=Verify TPM init is done and boots to kernel
Change-Id: I33f7427d1675190f65acf14679be93546e6db69a
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51086
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I73160985c025cb0945a4ac16c8c3ebb988d3858f
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52065
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The recent refactor of console UART GPIOs to mainboard's bootblock
caused brya boards to lose the first ~5 lines of the logs from
bootblock. Rename bootblock_mainboard_init to
bootblock_mainboard_early_init so that the UART pads will be ready
by the time the console is initialized.
BUG=b:184319828
TEST=First lines from report_platform.c are now seen in UART output
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4a4fadcc091bf9b1c9894f9afaf42baff63c73a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
To pack a struct, the `__packed` attribute must come after the `struct`
keyword. Moreover, unions cannot be packed (structs inside unions can,
though). Correct uses of `__packed` so that EEPROM structs get packed.
Change-Id: I39d2c9ebc370605d5623b134189aa95a074ec7c3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: <wouter.eckhardt@prodrive-technologies.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Background story (I think that's what great in opensource -
ppl leave there part of their lives): ;-)
While trying to fix audio jack not working with coreboot and
Windows 10 with some help from hell__ and nico_h on IRC nico_h
discovered that t420 and t430 hda_verb.c are the same:
<nico_h> oddly, in coreboot source T420 and T430 have the same
numbers for very different codecs... I suspect copy-pasta
Difference between /sys/class/sound/cardX/hwCXDY/init_pin_config
in vendor BIOS helped with the updated config. Connecting audio
jack now works flawless both in Linux and Windows.
Audio-related keyboard buttons: volup, voldown, mute works fine
both in Linux (Debian-based) and Windows 10. mutemic button works
(tested ie. with xev) but both in Linux and Windows 10 wont light
up or makes any effect.
+-----------------------------------+
| init_pin_config dump from: |
+----= VENDOR =---+---= coreboot =--+
| 0x19 0x04211040 | 0x19 0x04211040 |
| 0x1a 0x61a19050 | 0x1a 0x61a19050 |
| 0x1b 0x04a11060 | 0x1b 0x04a11060 |
| 0x1c 0x6121401f | 0x1c 0x6121401f |
| 0x1d 0x40f001f0 | 0x1d 0x40f001f0 |
| 0x1e 0x40f001f0 | 0x1e 0x40f001f0 |
| 0x1f 0x90170110 | 0x1f 0x90170110 |
| 0x20 0x40f001f0 | 0x20 0x40f001f0 |
| 0x22 0x40f001f0 | 0x22 0x40f001f0 |
| 0x23 0x90a60170 | 0x23 0x90a60170 |
+-----------------+-----------------+
Tested-by: Piotr Szymaniak
Signed-off-by: Piotr Szymaniak <szarpaj@grubelek.pl>
Change-Id: Ie5eba84e5ea590b7db00e189cd68e714bee7e410
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51612
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Micron DDR4 memory part MT40A1G16RC-062E-B 16Gb
index was generated by gen_part_id
BUG=b:184024142
BRANCH=zork
TEST=emerge-zork coreboot
Change-Id: I890a2da38c8cd1963e9ee7c5df9410b2b2538e9f
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Loading wifi_sar-vilboz-2.hex for vilboz LTE sku.
Loading wifi_sar-vilboz-3.hex for vilboz360 LTE sku.
BUG=b:183902165, b:176211194, b:183913210
BRANCH=firmware-zork-13434.B
TEST=Build coreboot and load the wifi sar table by fw_config
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I37a40456970e3f1dc8b2eed26aa23e3d75748222
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Enable I2C2 in devicetree and fill ACPI information for Codec and
Speaker amplifiers. Pass correct IRQ GPIO for headset jack.
BUG=None
BRANCH=None
TEST=Ensure that the Codec and Speaker Amplifiers are detected in
i2cdetect.
Change-Id: I1ae52a8bbaa0181c906cd14a94de22e0250ed4c1
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52046
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the BT disable GPIO to logic low in order to enable Bluetooth.
Add USB ACPI configuration for BT device.
BUG=b:182201890
TEST=Build and boot to OS.
Change-Id: I647c301e2db6d4a7c5c8cb31cbc47a44cba5e734
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Configure camera power GPIO to high
BUG=b:182207799
TEST=Build and boot to OS then checked camera device existence with lsusb
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Ie894167e3c4f8efdb3710599c6ff3a9fc975adb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Initialize all eSPI signals including PCIE_RST0_L early for EC
communication.
- Set PCIE_RST0_L to a GPIO and set it high to release the bus. This is
a temporary workaround until PCIE_RST_L comes up on its own.
- Make sure all GPIO muxes initialized early are re-initialized.
BUG=b:183340503
TEST=Boot Guybrush
Change-Id: I512cb8b435dc8412cd46189e741ad94e5a24699e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51675
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
