| Age | Commit message (Collapse) | Author |
|---|
|
https://ark.intel.com/products/71620/Intel-NUC-Board-DCP847SKE
Created using autoport and manual edits.
mainboard_fill_pei_data copied and adjusted from samsung/lumpy.
Tested:
- RAM slots with 2x4GB Kingston KVR1333D3S9/4G (DDR3-1333 1.5V).
- RAM slots with 2x4GB Kingston KVR16LS11/4G (DDR3L-1600 1.35V).
- SeaBIOS stable payload.
- Linux 4.13.14 payload.
- Booting into Linux 4.13.14 with Debian/unstable installed on the
internal mSATA slot.
- Non-native raminit (works).
- Native raminit
- KVR1333D3S9 doesn't work.
- KVR16LS11 only works at 1.5V.
- Native VGA init, HDMI port detection with libgfxinit.
- Basic ACPI functions (power button event; power-off; reboot).
- Suspend to RAM and resume works.
- PCIe WLAN in half-minicard slot.
- USB device in half-minicard slot.
- PCIe device in full-minicard slot.
- mSATA device in full-minicard slot.
- Fan spins up/down in response to CPU load.
Known issues:
- Native raminit fails timC calibration with the RAM I have.
- Technical Product Specification mentions overcurrent protection
for back panel and front panel USB connectors, but I haven't
been able to trigger it with either native fw or coreboot
(tried up to 2.5A load).
Untested:
- USB debug port.
Change-Id: I6e210310f55c051eaf61e0698fed855eda5d7d90
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/22683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This patch revises LED0 Green light behavior from patch 2ecf3f8c.
For 100Mb link speed, LED0 should be OFF.
BUG=b:65437780, b:68284778, b:69950854, b:65808944
BRANCH=None
TEST=Run DUT with 100Mb and 1000Mb ethernet connection and observe
LED0 is behaving as expected.
Change-Id: Ia805c955711b8ce77eba087a28427a005c456fa1
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22964
Reviewed-by: David Wu <david_wu@quantatw.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New UPD PcieRpClkSrcNumber introduced in FSP V2.9.2 to configure
clock source number of PCIe root ports. This UPD array is set to clock
source number(0-6) for all the enabled PCIe root ports, invalid(0x1F)
is set for disabled PCIe root ports.
BUG=b:70252901
BRANCH=None
TEST= Perform the following
1. Build and boot soraka
2. Verify PCIe devices list using lspci command
3. Perform Basic Assurance Test(BAT) on soraka
Change-Id: I95ca0d893338100b7e4d7d0b76c076ed7e2b040e
Signed-off-by: Divya Chellap <divya.chellappa@intel.com>
Reviewed-on: https://review.coreboot.org/22947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
firmware test team is requesting that default gbb flags set to 0x39
rather than 0x239 so that it's consistent with the default gbb flags
of other platforms.
BUG=b:70392534
BRANCH=None
TEST=emerge-fizz coreboot chromeos-bootimage
gbb_utility --get --flags image-fizz.bin and make sure
that it returns 0x39 instead of 0x239
Change-Id: Ib73e4619b13f6b7c2d01598c926fbbd7d7eb9bef
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22962
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable S0ix for fizz.
BUG=b:67598361
BRANCH=None
TEST=None. Need to be tested with EC and kernel as well.
Change-Id: I981d2cc7e969a44567b0f21f63f68c78e73f5cb5
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22955
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Don't rely on the cascading default values. Ensure Kahlee uses the fanless
versions of the SMU fimware by selecting it.
Change-Id: I0761266f2a4026ebc251b64074c10481118734a2
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
apu4 is new version of PC Engines platform, which contains 4 Ethernet
ports and 4GB of RAM. In functional way it is very similar to apu3.
Platform tested with booting Linux voyage (kernel 3.16.7) using USB and
SeaBIOS as 1st stage and GRUB as 2nd stage bootloader. Also Debian
(kernel 4.8.5) using iPXE.
Change-Id: Ia7a9971d25d4ecc215c392be1e46dc1c10129ba7
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-on: https://review.coreboot.org/22629
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
In commit 7f5efd90e (intel/bd82x6x: Use generated ACPI PIRQ)
the default_irq_route.asl file was removed, but this mainboard
was missed. Follow suit with the original intent of the commit
and fix the build breakage.
Change-Id: Iac233b802239e4e5cfc66d9545bb637ec4f9f541
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22958
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This patch configures the EC_SCI_GPI when ESPI is enabled.Also adds
mainboard espi handler function.
TEST= Boot to OS and SMI/SCI is working when ESPI is enabled/disabled.
Change-Id: I2b3845d54ad7c1f14edc86f71b3f968424711999
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
coreboot console output during POST shows that the EC
replay fails to communicate with the EC. Since the replay
has no effect, it should be removed from the boot process.
coreboot log:
Replaying EC dump
.......Timeout while sending command 0x81 to EC!
.......Timeout while sending data 0x00 to EC!
(snip)
.......Timeout while sending command 0x81 to EC!
.......Timeout while sending data 0xff to EC!
.......Timeout while sending data 0xff to EC!
done
Change-Id: I05fb6358b40f442337f5768afa6253cd9bc32ee1
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Reviewed-on: https://review.coreboot.org/22736
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There is a potential IMVP8 issue for KBL that affects Intersil VRs
Fizz is using one of the affected parts. The fix is to use an updated
microcode and also send a mailbox box command from FSP.
BUG=b:65499724
BRANCH=None
TEST=Build and boot Fizz
Change-Id: Iebfda02df88ea0d2aaf79e8449b95c0eb2165c6b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/22763
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The Intel version of ThinkPad X131e can ship with Sandy Bridge or
Ivy Bridge processors. The mainboard uses 8MiB+4MiB flash chips, with
the 8MiB chip containing the IFD and ME, and the 4MiB chip containing
the BIOS. The flash chips can be accessed with an external programmer.
This port was primarily created using autoport, with some parts adapted
from lenovo/x230 and google/stout.
Tested and working:
- Machine type 3367AH5 / Intel Celeron 887 (Sandy Bridge)
- Boots Debian GNU/Linux 9.2 (Linux 4.9.51) via SeaBIOS
- Boot from internal SATA and USB
- Native RAM init
- Native VGA init
- libgfxinit
- VGA and HDMI display output
- Keyboard, trackpoint, touchpad
- Audio (speaker, headphones)
- Ethernet (Realtek)
- Display backlight
- USB 3.0 ports
- "Always on" USB port (EHCI debug)
- SD card reader
- Webcam
- Fan and temperature sensors
- ACPI S3 (Sleep)
- CMOS
- TPM
Not tested:
- WLAN/Bluetooth (Broadcom)
- WWAN/mSATA (no card)
- Other operating systems
Not working or not implemented:
- Fn keys
- ACPI S4 (Hibernation) "Image mismatch: memory size"
Change-Id: If8de3a9308997e2d57aee869023ee9a43a2db872
Signed-off-by: James Ye <jye836@gmail.com>
Reviewed-on: https://review.coreboot.org/20694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
In order to pass USB2 eye diagram, some USB2 port PHY registers
needs to be changed.
Port1 (Type-A): USB2_PORT_SHORT
Port2 (BT): USB2_PORT_SHORT
Port6 (H1): USB2_PORT_SHORT
Port7 (Camera): USB2_PORT_SHORT
BUG=none
BRANCH=master
TEST=emerge-nautilus coreboot and do eye-diagram test
Signed-off-by: sh.kim <sh_.kim@samsung.com>
Change-Id: I174e5bf96a53bb210481fb88298d5341f6c11dec
Reviewed-on: https://review.coreboot.org/22686
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The current fan level should be zero at boot and only be modified by
ACPI or SMI code.
Change-Id: I72b59f05746b28cfb24c4f018aebc2befa9caba6
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/22796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Enable change Ic6b8ce4a9db50211a9c26221ca10105c5a0829a0
(sb/intel/common: Automatically generate ACPI PIRQ) for BD82X6X.
This generates the main ACPI _PRT table automatically based on the
chipset registers.
Tested on Intel NUC DCP847SKE with Linux 4.13.14:
$ cat /proc/interrupts
CPU0 CPU1
0: 23 0 IO-APIC 2-edge timer
8: 1 0 IO-APIC 8-edge rtc0
9: 0 0 IO-APIC 9-fasteoi acpi
19: 86 0 IO-APIC 19-fasteoi ehci_hcd:usb1
23: 0 0 IO-APIC 23-fasteoi i801_smbus
[...MSI and other interrupts skipped...]
Log messages:
ACPI_PIRQ_GEN PCI: 00:02.0: pin=1 pirq=1
ACPI_PIRQ_GEN PCI: 00:1b.0: pin=1 pirq=1
ACPI_PIRQ_GEN PCI: 00:1c.0: pin=1 pirq=2
ACPI_PIRQ_GEN PCI: 00:1c.1: pin=2 pirq=6
ACPI_PIRQ_GEN PCI: 00:1c.2: pin=3 pirq=4
ACPI_PIRQ_GEN PCI: 00:1d.0: pin=1 pirq=4
ACPI_PIRQ_GEN PCI: 00:1f.2: pin=1 pirq=2
ACPI_PIRQ_GEN PCI: 00:1f.3: pin=2 pirq=8
ACPI_PIRQ_GEN PCI: 00:04.0: pin=1 pirq=1
Generated _PRT:
Scope (\_SB.PCI0)
{
Method (_PRT, 0, NotSerialized) // _PRT: PCI Routing Table
{
If (PICM)
{
Return (Package (0x09)
{
Package (0x04)
{
0x0002FFFF,
0x00000000,
0x00000000,
0x00000010
},
Package (0x04)
{
0x001BFFFF,
0x00000000,
0x00000000,
0x00000010
},
Package (0x04)
{
0x001CFFFF,
0x00000000,
0x00000000,
0x00000011
},
Package (0x04)
{
0x001CFFFF,
0x00000001,
0x00000000,
0x00000015
},
Package (0x04)
{
0x001CFFFF,
0x00000002,
0x00000000,
0x00000013
},
Package (0x04)
{
0x001DFFFF,
0x00000000,
0x00000000,
0x00000013
},
Package (0x04)
{
0x001FFFFF,
0x00000000,
0x00000000,
0x00000011
},
Package (0x04)
{
0x001FFFFF,
0x00000001,
0x00000000,
0x00000017
},
Package (0x04)
{
0x0004FFFF,
0x00000000,
0x00000000,
0x00000010
}
})
}
Else
{
Return (Package (0x09)
{
Package (0x04)
{
0x0002FFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKA,
0x00000000
},
Package (0x04)
{
0x001BFFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKA,
0x00000000
},
Package (0x04)
{
0x001CFFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKB,
0x00000000
},
Package (0x04)
{
0x001CFFFF,
0x00000001,
\_SB.PCI0.LPCB.LNKF,
0x00000000
},
Package (0x04)
{
0x001CFFFF,
0x00000002,
\_SB.PCI0.LPCB.LNKD,
0x00000000
},
Package (0x04)
{
0x001DFFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKD,
0x00000000
},
Package (0x04)
{
0x001FFFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKB,
0x00000000
},
Package (0x04)
{
0x001FFFFF,
0x00000001,
\_SB.PCI0.LPCB.LNKH,
0x00000000
},
Package (0x04)
{
0x0004FFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKA,
0x00000000
}
})
}
}
}
Change-Id: I832a86925283d61b64b8268246d9e6f11994c120
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/22859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
SATA was enabled only for internal testing. Since we do not use
SATA on chrome platforms, it can be disabled.
Change-Id: I907b440562b39e6d97f604e7e63b6b99e487aaa8
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/22875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
It seems that RAM code 0 has been strapped with an incorrect resistor on
Kevin. The resulting voltage divide still puts it well within the ADC
value bucket reserved for that slot, but a little closer to the edge
than necessary. While this doesn't seem to cause any immediate problems
on its own, it still doesn't hurt to fix it (if only for the
documentation value).
On other boards (at least on my Scarlet) the strapping seems to be
correct.
Change-Id: Ic5199834fbeaf734e725ff45b04f45eefe149855
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22891
Reviewed-by: David Schneider <dnschneid@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch shifts some comments around to make it easier to replace
values in the ADC strapping bucket table with compile-time conditionals.
Change-Id: Ic51917d3961a51d4e725ff824fb59aeefe149855
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This change adds SPD files for memory IDs 1-4 on nami.
BUG=b:70182907
Change-Id: Ic43f944c0cde18244fe4c4d21314b831d048a3a2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Nami uses MAX98357A speaker amplifier and DA7219 codec. This patch
adds max98357a and da7219 under I2C #3 in devicetree and adds SPK DMIC
nhlt support for 4CH DMIC.
BUG=b:70646770
TEST=emerge-nami coreboot
Change-Id: Iecf4059f8ea3d5e34f33f0be227897a8cca636fa
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
ACPI bit is not set after an S3 resume, so set it in _WAK. Setting
SLPT bit can make the power LED blink in S3.
Change-Id: I2badc69510275df57938cb8607b3c4e0df50f028
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/22929
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This platform shares most hardware components with first-gen Core
Lenovo laptops such as T60/X60, with much smaller EEPROM size as
one of notable differences. The port features Intel graphics,
ATI-based version should work with vendor VBIOS.
Tested peripherals:
- sleep/resume,
- USB ports,
- ACPI Fn key bindings/volume buttons,
- backlight control,
- ethernet,
- wireless (under Linux),
- sound/beep,
- dock handling,
- serial via dock.
Untested peripherals:
- IrDA,
- parallel port,
- PCMCIA,
- S-Video port,
- modem,
- FP reader (should just work),
- IEEE1394.
Linux 3.16 works with native gfxinit perfectly, with Intel VBIOS
console sometimes displays nothing when i915 framebuffer is used.
Windows 7 has an interrupt assignment issue with iw3945, otherwise
tested stuff is fine.
Change-Id: I84c89cc47d3db126d827f92d50270954bc42f224
Signed-off-by: Andrey Korolyov <andrey@xdel.ru>
Reviewed-on: https://review.coreboot.org/21019
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add initial files to support the Saddle Brook board. This board uses the
Skylake FSP 1.1 image and does not build without the FspUpdVpd.h file.
Most of the code has been taken carried over from kunimitsu with changes
done for Saddle Brook.
Saddle Brook is a reference board for Skylake SOC and has DDR4.
TEST=Build with uefi payload and boot to Linux 4.9 on CRB successfully.
Change-Id: Ie221eb58e8ab8ff15e9ef19c1d145a5eb2921b4e
Signed-off-by: Anuj Mittal <anujx.mittal@intel.com>
Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com>
Reviewed-on: https://review.coreboot.org/21436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
BUG=b:70773281
Change-Id: If9b575568cabcbee03ad190b69d9c033890f7fa6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22927
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per the latest schematics, this change configures GPP_B0 for WLAN
wake and uses corresponding gpe bit in ACPI node for WLAN. This hasn't
been tested yet.
BUG=b:70775494
Change-Id: I5198b8083a87d00f890b45986e5e3f62b81686c2
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22928
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change configures the GPIOs for pen reset and eject lines and
exports required properties using ACPI table.
BUG=b:70773138
Change-Id: I52f6c3dced54259cde8ee6753275622622e15954
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Similar to other KBL projects, this change enables AER and LTR for
root port 1 on poppy.
BUG=b:65570878
Change-Id: Iadad3d2fc46cbba575a776071305925c529a6760
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=b:62726961
Change-Id: I5a88e67d5a22f8a39427c95821ffee4f2fd717fa
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change really fixes the SataMode to select non-RAID mode and
enables SATA which was incorrectly disabled in a71276b
(mb/google/poppy/variants/nami: Fix SataMode configuration in
devicetree).
BUG=b:70160119
Change-Id: Ied6adabdc1d2458972bde628616a198cd41f9f3e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
GPP_F3 is not connected on poppy or any of its variants. This change
configures GPP_F3 as NC on poppy and all the variants.
BUG=b:70160119
Change-Id: I303276ab9546d56c846755fa3a6142978f6b8c92
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Nami uses DEVSLP1 and not DEVSLP0. This change updates the GPIO
configuration for DEVSLP to match the latest version of schematics.
BUG=b:70160119
Change-Id: Ifa181322011a4b8947ecd0fa44dcf790b0d8f657
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch enables customized NIC leds as below:
Green Orange (Amber)
100M off blinking
1000M on blinking
BUG=b:69950854
TEST=Boot on fizz dut and observe the LEDs are behaving as expected.
Perform suspend/resume test and the LEDs are still working as expected.
Change-Id: Ic70587a0cd688e74b5e1ce532c5da954c80cf841
Signed-off-by: David Wu <david_wu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Similar to Fizz, SataMode on nami should be set to AHCI. This change
fixes the configuration error done in 903472c
(mb/google/poppy/variants/nami: Add support for nami board).
BUG=b:70160119
Change-Id: Ia88b56ae6bd9121f8447f7c1a2f5a10990fb8ed5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22845
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
PCH_SPK_EN uses GPP_A23 and not GPP_A22. This change fixes the gpio
configuration error in the initial change 903472c
(mb/google/poppy/variants/nami: Add support for nami board).
BUG=b:70160119
Change-Id: I90d9c009369c53cfec47fe77356e181d5ecf7ad5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22844
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Melfas kernel TS driver (melfas_mip4.c) will look up "ce"
GPIO during driver probe in ACPI _DSD.
But FW does not report "ce-gpios" but "enable-gpios" in _DSD.
Kernel will obtain GPIO from _CRS by index "0" without ID.
Melfas driver does not have separate condition
for MIT-410 so driver will set TS IC power off in probe.
FW now may need to add back "reset" pin in order to hack
this condition to let Melfas driver get "useless" GPIO
so TS IC power (VTSP) will be not off during driver probe by itself.
BUG=b:70149336
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: Icf0451ff0c3df97cb2474e30542a2f46ba67d82a
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
For Fizz, the default should be AHCI mode and not RAID
mode. Additionally, there is only one drive connector, so
attaching several drives for a RAID is hard.
BUG=b:70146894
Change-Id: I2a9aa2d6281a916c00ff4659a927f164ba0e0705
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/22837
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Configure PRMRR to allocate 128MiB for SGX enclave memory and enable SGX
by default for GLKRVP platform.
Supported PRMRR size options:
0x02000000 - 32MiB
0x04000000 - 64MiB
0x08000000 - 128MiB
Change-Id: Ifa39df4a1da84bae49551a9626257bda0729752b
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The overcurrent pins on kahlee weren't mapped correctly, causing
the USB-A port to stop working.
None of the EHCI only ports are used for external connectors, so all
of the overcurrent pins should go to the XHCI connections. This is
also true of the Grunt board.
On Grunt, this also means that we don't need OC3, as it doesn't map
to anything in the XHCI controller, as it's coming from an internal
hub.
BUG=b:70636233
TEST=Build & boot Kahlee, verify USB-A port is working again.
Change-Id: I53336a18a26bd9be27c7265fddbcd780632656bf
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
|
|
This patch enables the APLS touchpad in glkrvp platform.
TEST= Boot and test touchpad works.
Change-Id: I6f52f7db57ab52b5531e647bde2adbb78b40f76f
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22627
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch enables the APLS touchpad in cnl-y platform.
TEST= Boot and test touchpad works.
Change-Id: I461b9d119b1cac6c8c6cb9b096697f58e00d80ad
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22369
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change selects Kconfig option to disable native SD card
controller in ACPI tables, since it is not used on nami.
BUG=b:70160119
Change-Id: I6180c2b342c69e6a7c357f10b6297d67ea0211d7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable SATA port 0 to support SATA HDD.
BUG=b:69950854
BRANCH=None
TEST=emerge-fizz coreboot and boot on fizz dut
Change-Id: Ifbf5950151758286f8bff7250a68d9d0b3975ef9
Signed-off-by: David Wu <david_wu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
MEM_ID SPD
0000 hynix-H5AN8G6NAFR-UHC
0001 hynix-H5ANAG6NAMR-UHC
0010 micron-MT40A51216JY-083E
0011 micron-MT40A1G16KNR-075E
0100 samsung-K4A8G165WB-BCRC
0101 samsung-K4AAG165WB-MCRC
BUG=b:69268926
TEST=build test
Change-Id: I1fd6335b3f8842252c42009a0a91a5b6ed3ea238
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22748
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add INNOLUX P097PFG panel timing. According to Scalet schematic,
if GPIO3_D4 get low status, it will use INNOLUX P097PFG panel;
if GPIO3_D4 get high status, it will use KD097d04 panel.
Change-Id: I43fa5d859a9a529a84c58a953b37d03953ce648a
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Move AGESA related headers in soc/amd/common to
soc/amd/common/block/include/amdblocks.
BUG=b:69262110
TEST=Build with no error gardenia and kahlee (no code change, headers moved).
Change-Id: I5d3064625ddf8caaf370aabaf93165c6817f1ca0
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Also adds a comment in the code to clarify what this array is about.
Change-Id: I04b185a5dbd7a7ccb039820f19d2cb549b9a2eac
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
This change provides implementation of variant_memory_params for
nami. Since it uses DDR4 memory, DQ-DQS mapping table is not
required. Also, Rcomp resistor values are provided based on SDP v/s
DDP memory.
BUG=b:70188937
Change-Id: Ic1d0cfdb7d8b02fa0be0a4c54b20057a4c2fc3ce
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change updates scl_lcnt value for I2C5 to bring the bus frequency
closer to 400kHz.
BUG=b:65062416
TEST=Verified that I2C5 frequency is between 389-396kHz.
Change-Id: Ibaccab0c797174332633cb75e30d18ff5af76a43
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The following files need to be moved: amd_pci_util.c, amd_pci_util.h and
spi.c. The remaining files are AGESA related and will be part of a separate
issue/commit.
BUG=b:62240201
TEST=Build with no error gardenia and kahlee (no code change, just folder
reorg).
Change-Id: I3f965afa21124d4874d3b7bfe0f404a58b070e23
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Due to a schematic error, our code was written to configure more I2S0
pins than are actually used. We're also pinmuxing the whole bank of pins
over to the I2S controller even though we don't need them all. Restrict
the GPIO initialization and pinmuxing to the pins we really need so the
other ones can be correctly used as SKU ID pins on Scarlet.
Also, move the "audio" IO voltage domain selection to the other such
selections in the bootblock, since that covers two whole banks of GPIOs
and there's no guarantee that they're all used for audio (and thus not
needed before ramstage).
BUG=b:69373077
TEST=Booted Scarlet, confirmed correct SKU ID (7) was detected on rev2.
Change-Id: I9314617e725fe83d254984529f269d4442e736f1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
|
|
These pins need to be pull-ups. I forgot.
BUG=b:69373077
Change-Id: I9314617e01d35898254984529f269d4442e736f1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make lint-stable was giving an error on this.
Change-Id: I06d11d86151f683b82b6df537e3de8c52d33e8b4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
|
|
Adds Maxim98357a support for Nautilus using the generic driver
in drivers/generic/max98357
BUG=b:68686020
TEST=With entire merged audio should be enabled on max98357
speaker codec.
Change-Id: I958bf7c1395259b3e3fb30332882fd51a48dc0cc
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/22458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Nautilus board uses max989357a speaker codec and 4CH DMIC.
Select the appropriate NHLT blob to be packaged in CBFS.
Also generate the required ACPI NHLT table for codec
and the supported topology in nautilus.
BUG=b:68686020
TEST=With the required driver support in kernel verify that
the Audio plays on Speaker and captures on 4CH DMIC
Change-Id: Ie90af02e0935029f53f9020bd78027b6eb31a187
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/22457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Removes rs780_before_pci_init() since it was a no-op anyway.
Removes get_nb_rev() since this function is provided via a macro in
the header.
This Makes a lot of function non-static since the header has
prototypes for these.
Change-Id: I8933516771d959583bbd59a5c1beee3e30a7004f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: Ib1b761fc417f1bb000f408d3bed5e8666963f51d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/22603
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add proper variants gpio.h in dsdt.asl where the GPE_EC_WAKE and
EC_SCI_GPI is defined.
Change-Id: Ideb6dd4d0ac496a81721cd883865218cb19583d9
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In the original Chromium source, PcdMemorySpdPtr is only set for
cyan, but none of the other Braswell variants. When upstreamed,
it was left set for all boards as it didn't appear to be problematic.
In wider testing, I came across one reks board for which it caused
FSP memory init to fail, so restricting the parameter to cyan only
as it was originally.
TEST: build/boot google/reks with Micron EDF8132A3MA-JD-F RAM,
observe board now successfully boots where it did not previously.
Change-Id: Iacfbd4bc89fa04717baf85704181d346bca2ed2f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22782
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- The touchscreen interrupt was moved from the GPIO 3, as originally
suggested to GPIO 11. This changes the gevent from 2 to 18.
- Add EMMC reset on GPIO 93.
- Add EMMC bridge PCIe reset on GPIO 40.
- Set device enables to high.
- Remove extra SCI comment from GPIO 130.
- Set individual device PCIe reset pins to high.
- Enable global PCIe reset on GPIO 26.
- Mark LPC_CLK1 as unused.
- Update net names based on latest schematics.
- Set Direction and level/edge correctly for SCIs/SMIs.
- Remove SCI for pen detect.
- Add comments.
BUG=b:70234300, b:69681660, b:69305596
TEST=build grunt
Change-Id: Ib591e4278ed23d0963ecb19ad9c326498b4c7796
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
- Grunt moved the EMMC chip to port 2, where Kahlee had the SD reader on
PCIe port 1, so move the OemCustomize file into the variant directory.
- Add comments in baseboard version so it's easier to understand.
- Update reset pins, put the definitions in gpio.h
BUG=b:70255003
TEST=Build and boot Kahlee. Build Grunt.
Change-Id: I78ec72e9d6fd52b8ac75e7187bd01ee7ddc3ba2a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
On GLK EC does not support temperature reads and does not control
the fans anymore, OS is responsible fan control through EC.
This hack enables running of the fan for boards without External EC.
Change-Id: I361e53d4fd53678f3abb8fe9862071aec6e149a7
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-on: https://review.coreboot.org/22235
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This patch does not put CLKRUN in IOSTANDBY.
Change-Id: I7fedd729d3bb66c2b52a63166e461f8760457721
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch makes coreboot set the max current and voltage for barrel jack
adapters.
BUG=b:64442692
BRANCH=none
TEST=Boot Fizz. Use chgsup console command to verify the max current and
voltage are set as expected.
Change-Id: Ifebee09096e0935cc7d3e53920a251b0496d3c55
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/22623
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allow overriding specific GPIOs by SKU ID. Override two GPIO settings
for nasher to save the power consumption when the system in S0ix.
Change as below:
AVS_DMIC_CLK_A1: IGNORE -> Tx1RXDCRx0.
AVS_DMIC_CLK_B1: IGNORE -> Tx1RXDCRx0.
BUG=b:69025557
BRANCH=master
TEST=compile/verify the power consumption change from ~150mW to ~100mW
on clamshell SKU and from ~200mW to ~100mW for convertible SKU.
Change-Id: I9e0674f206426fddb3947273754774b310106334
Signed-off-by: Chris Wang <chriswang@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/22752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Skip LPC related gpio configuration if eSPI config option
is selected.
Change-Id: I15c5f769f36a1801217b1e3650379c7b181d814f
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/22757
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With the old timing, the hblank time isn't large enough,
it may cause display artifacts. So fix it.
BUG=b:70160653
TEST=panel work on Scarlet rev2 board
Change-Id: Ib061f5e215611d20f59e3f24cfe3c7fbc507ebed
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This logical device is disabled in OEM BIOS. Disable here to match,
since its support is currently incomplete anyway.
Change-Id: I5c07136ec6a14a8ee8cb68537a2663b78fc0fa20
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/22145
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Updates ACPI tables with work done for asus/p2b-ls, including super I/O
related declarations.
Change-Id: Id2420da4ab04aa5f59ac0aa237d21477a03b826e
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/22473
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add ACPI tables support that will be needed for soft-off and S3 resume in the future.
Boot tested for soft-off.
Change-Id: I28b559406bd53efc555dcbb8282dfe2bd6d1af87
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In preparation to deleting early_setup,c, change early_ec_init() to use new
southbridge.c function sb_set_wideio_range and remove <#ifdef __PRE_RAM__>.
BUG=b:64033893
TEST=Build, boot and check serial output, search for "Covered by wideIO xx",
which should match earlier message "Range assigned to wide IO xx" generated
within modified early_ec_init().
Change-Id: Iaea17f4f636aab6bd8b05b1b3bed53a677164e74
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change adds variant nami derived from baseboard poppy.
BUG=b:70160119
Change-Id: Ic6795d49d3e6e98a32f4af0b621e8bb463041412
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change updates memory SPD handling code in baseboard poppy to
allow variants to define either LPDDR3 or DDR4 memory types. In
addition to that, it also updates the function to print SPD info
considering offsets that might be different across the two memory
types.
BUG=b:70188937
Change-Id: Iefad01719c62264fb0d7e987904e77647d6026c2
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Until now, nautilus was using the DQ-DQS mappings provided by the
baseboard. However, based on schematics, these values are not
correct. This change adds DQ-DQS mapping tables for nautilus.
BUG=b:70188533
Change-Id: Ife6ba19b8fe8873ab8cca977ca8f34a4d86e8e6e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22706
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: shkim <sh_.kim@samsung.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Audio DMIC_CLK needs to be ON in S0ix to support Wake on Voice.
So, configuring GPIO_171 to be as IGNORE IOSSTATE, so that
clock is ON in S0ix state.
BUG=None
TEST=put DUT in S0ix, verified DMIC_CLK
in scope when wov capture path is ON
Change-Id: I147cf3c12acb11429c6cb234e8c511f57886b6b4
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/22675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Scarlet has SKU detection strapping pins now. This patch adds the code
to read them.
BUG=b:69373077
Change-Id: I8d889a845950923bc7b5be9b79792cf3c8b6b8ad
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22697
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch switches the board_id and ram_code helper framework to use
weak functions rather than Kconfigs to determine whether the board
supplies these IDs. This cuts down on the amount of boilerplate Kconfigs
many boards have to set and also gives them more flexibility, such as
being able to determine at runtime whether a given ID is present.
Change-Id: I97d6d1103ebb2a2a7cf1ecfc45709c7e8c1a5cb0
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22695
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Merge the different coreboot table strapping ID structures into one
because they're really just all the same, and I want to add more. Make
the signature of the board_id() function return a uint32_t because
that's also what goes in the coreboot table. Add a printk to the generic
code handling strapping IDs in ramstage so that not every individual
mainboard implementation needs its own print. (In turn, remove one such
print from fsp1_1 code because it's in the way of my next patch.)
Change-Id: Ib9563edf07b623a586a4dc168fe357564c5e68b5
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The BOARD_ID_MANUAL and BOARD_ID_STRING options were introduced for the
Urara board which is now long dead, and have never been used anywhere
else. They were trying to do something that we usually handle with a
separate SKU ID these days, whereas BOARD_ID is supposed to be reserved
for different revisions of the same board/SKU. Get rid of it to make
further refactoring of other options easier.
Also shove some stuff back into the Urara mainboard that should've never
crept into generic headers.
Change-Id: I4e7018066eadb38bced96d8eca2ffd4f0dd17110
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22694
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I6f0d6d7fefc77fb05cdb629d09de8cb72496a9cc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22664
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Variants nautilus and soraka currently provide the exact same
definition for variant_cros_gpios as provided by the baseboard. This
change removes the function defintions from variants so that the weak
definition in baseboard can be used.
Change-Id: Ic88623f34039792f0f9fb46842b24e4f1290981b
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22705
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds a new config option VARIANT_HAS_CAMERA_ACPI to allow
variants to define ACPI tables for camera support. It also prevents
boards that do not need this from unnecessarily providing dummy files
for camera ACPI support.
Change-Id: I91f8e407e0f021071eeadbde8c2695e2a6d69e06
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change the prefix for TPM options from POPPY_USE_* to
VARIANT_HAS_*. This makes it clear that these are variant specific
options.
Change-Id: I6fd120a34a5b0c1f018164d5c2b60548da1d0f61
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In order to allow variants to select different Kconfig options, this
change adds VARIANT_SPECIFIC_OPTIONS_${VARIANT_NAME} which can be
selected by each variant in Kcnonfig.name.
Change-Id: I15db2fdac5c9e55f9698c8a0c083d6467afae245
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22700
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change removes the dynamic disabling of TPM based on config
options. Poppy and its variants will have only one type of TPM
supported and so there is no need to update it dynamically.
Change-Id: Ie82825fcf7092e845583edaac9ba0d3fc9d1dd80
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22704
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Soraka is no longer using SPI TPM. This change disables GSPI0 in
device tree and updates gpio config accordingly.
Change-Id: Ia0554ce3a0d553631123cc2b23b6dc2f6f40a1a3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Mainboard poppy is no longer using SPI TPM. This change disables GSPI0 in
device tree and udpates gpio configuration accordingly.
Change-Id: I713e41c45e323bf13aa79412ec679c90121a52b2
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Set the USB over current pins for the Grunt baseboard and
Kahlee mainboard. Removes the ACPI ASL OC code, which is not
used on Stoney Ridge SOC.
BUG=b:69229635
TEST=Build and boot Kahlee. Not tested with OC test fixture.
Change-Id: I5a9b3409d9c91b89fd02f8eecf9e04c435f14342
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22679
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
There is some confusion with old RAMID table, make it clear,
and let's no longer tangle it in future.
Change-Id: I44215b4a6668074575a5df691ac1ff8fa3d15492
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This change updates device tree deep_sx_config to disable internal
pull-down on AC_PRESENT.
BUG=b:69983729
Change-Id: I041900a5262f8fd920856f126185329242a0639a
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22689
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
After applying this change, /dev/tpm0 is visible inside GNU/Linux
with kernel 4.9.51-1 from Debian, and there is a menu item shown
inside SeaBIOS' (master only) interface if ESC is pressed.
The TPM is confirmed working with [Heads](https://github.com/osresearch/heads).
Change-Id: I3b845928954d203d1c3608b6704fedbd590e1fa9
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/22602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch enables WOL feature.
BUG=b:69290148
BRANCH=None
TEST=powerd_dbus_suspend && sudo etherwake -i eth0 $MAC to make sure
the system could be woken up by WOL packet.
Change-Id: I1178a776db2cdb448fe6650d49ae6c0281ac1128
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22606
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=none
BRANCH=none
TEST=none
Change-Id: I4e61f1327027c5100773e2b837f439a939807e72
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/22662
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Lava numbers are in.
BUG=b:69990330
BRANCH=none
TEST=verified that USB signal is within spec
Change-Id: I7416ec8d058271700ebe43f8d92af61c6c0d6b42
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/22661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quantatw.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
These files aren't needed for the overcurrent functionality.
BUG=b:69305596, b:69229635
TEST=Build Grunt & Kahlee. Overcurrent wasn't yet enabled so no other
testing was needed.
Change-Id: I8dcd50a249e387ccf1142949b359cee09942460a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Add initial baseboard GPIOs based on grunt schematics.
BUG=b:69305596
TEST=Build grunt
Change-Id: I4efcee7dbf54fb9ea82e5e9394db805bb69203c8
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Update the variable ${CONFIG_VARIANT_DIR} to use parens instead. Either
is valid, but since we use parentheses everywhere else, it's better to
be consistent.
BUG=b:69691210
TEST=Build grunt & kahlee
Change-Id: Ieffabaae5516a893f1dc1f7195a17c4cdeae8853
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22656
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change disables DPTF until the support is properly added in
dptf.asl
Change-Id: I68f2442e00718a4edbb34661d31d3a415d41c29f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Use EC to perform FAN control.
BUG=b:67487721,b:69404739,b:64439568
BRANCH=master
TEST=emerge-fizz coreboot and boot on fizz dut
Change-Id: I3394d3af9cbdb3eab1f18254909f60e2704735c3
Signed-off-by: David Wu <david_wu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: TH Lin <t.h_lin@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Add coreboot support for CompuLab Intense-PC (Ivy Bridge)
Modifications:
- Memory SPDs have been fixed to detect both installed SODIMM modules
- Full-height Mini-PCIe slot defaults to PCIe mode
- mSATA can be chosen instead of mPCIe via Kconfig option ENABLE_MSATA
Tested (Xubuntu 17.10/Linux 4.13 where applicable):
- 2+2GB DDR3-1600 SODIMMs pass memtest
- 4+4GB DDR3-1600 SODIMMs pass memtest
- 4+8GB DDR3-1333 SODIMMs pass memtest
- 8+8GB DDR3-1333 SODIMMs pass memtest
- Booting via USB working (with no SATA HDD present)
- Booting to main SATA HDD working
- DisplayPort and HDMI output working for coreboot init (*requires* VGA BIOS)
- DisplayPort and HDMI dual-head working in Linux
- Mini-PCIe devices (half/full-height) detected in Linux
- mSATA working (when chosen using ENABLE_MSATA)
- Onboard Intel 82579 GbE working
- Secondary Realtek 8111 GbE working
- Rear eSATA ports working
- Onboard analog audio output working
- HDMI audio output working
- USB 3.0 working
- Suspend to RAM (S3) working, but not tested extensively
- Mini PCIe WiFi
- FACE module FM-4USB (4 USB 2.0 ports)
Disabled/unsupported:
- TPM (BTO option, not included in base config)
- FACE modules:
- FM-USB3 (USB 3.0/mSATA) NOT SUPPORTED/TESTED
- FM-SER (serial) NOT SUPPORTED/TESTED
- FM-XTDEU2/4 (LAN) NOT SUPPORTED/TESTED
- FM-XTDE4U2/4 (Quad LAN) NOT SUPPORTED/TESTED
- FM-XTDM2 (dual mPCIe) NOT SUPPORTED/TESTED
- FM-VC (video capture) NOT SUPPORTED/TESTED
- FM-POE (Quad LAN w/PoE) NOT SUPPORTED/TESTED
Not tested:
- RS-232
Product information:
http://www.fit-pc.com/web/products/intense-pc/
Change-Id: I741b0b2f87eb9147c375b405a5b6989a10c7ad0a
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Reviewed-on: https://review.coreboot.org/22210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Change-Id: I22241427d1405de2e2eb2b3cfb029f3ce2c8dace
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/22585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
