| Age | Commit message (Collapse) | Author |
|---|
|
List of changes:
1. Add devicetree.cb config parameters related to FSP-S UPD
2. Configure GPIO as per ADL-P RVP
3. Add files required for ramstage(ec.c, mainboard.c)
4. Add smihandler.c for SMM
5. Add devicetree changes as below
- USB OC PIN programing
- GPE configuration
- SATA port mapping
- LPSS configuration
- Audio configuration
- IA common SoC configuration
- EDP configuration
- TCSS USB configuration
- Enable S0ix
TEST=Able to boot ADL-P RVP without Chrome EC (using on-board EC) with
UART log over legacy UART0 port as 0x3f8 with NVME at RP9 reach till
depthcharge payload.
Change-Id: I120885956c88babfa09d24ce1079d49306919b8a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
These settings are not necessary for DDR4 and can be dropped.
Change-Id: I1946be239f0c90db995a60570474039cef45cfa9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Add tcc, critical, passive policy, and pl values from thermal team.
BUG=b:169215576
TEST=build and verify by thermal tool
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I4f61eaa7eab2b86b04ff0541886621afb3082b1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Enables Pcie M.2 support for WWAN and disable M.2 USB.
RP4 is already on and PcieRpEnable[3] is enabled. Clock source 2 is already
configured. Added missing gpio configuration.
BUG=none
TEST=Boot to OS, check WWAN functionality
Change-Id: Ie9b7915062b2ef65d881d478e64322c0b8765614
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45828
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add generic wifi ACPI entry for wake on lan event.
Change configuration of GPIO 2/WIFI_PCIE_WAKE_ODL to SCI.
BUG=b:162605108
TEST=$ iw phy phy0 wowlan enable disconnect
$ cat /proc/acpi/wakeup | grep WF
WF00 S3 *enabled pci:0000:01:00.0
$ powerd_dbus_suspend
Reboot wifi router, DUT wakes up
BRANCH=zork
Change-Id: Idbeb2cfbc4995b8382ffc26cbe7b53764fc9252d
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45745
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable ALS ACPI devices for dooly.
BUG=b:168426118
BRANCH=puff
TEST=Ensure that ALS devices are enabled in ACPI tables.
Change-Id: Idd44d6ae1e7b62939fdfc3a0ab01924d2c1714aa
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Change-Id: I1e0489ec6730760f74102cdd00e4aaa66975d69a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Make output AML file name uniform.
Change-Id: Ic6cac4748a6159c695888b2737ada677d91f4262
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I5a5f4e7067948c5cc7a715a08f7a5a3e9b391191
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Create the elemi variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:170604353
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_ELEMI
Change-Id: I6013b6d8b28610a79f5ec49d373b2897799bffef
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Change-Id: I71ee54116ade4d6826dffc31ee879a70d3fc967f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This change switches all mainboard devices to use drivers/wifi/generic
instead of drivers/intel/wifi chip driver for Intel WiFi
devices. There is no need for two separate chip drivers in coreboot to
handle Intel and non-Intel WiFi devices since the differences can be
handled at runtime using the PCI vendor ID. This also allows mainboard
to easily multi-source WiFi chips and still use the same firmware
image without having to distinguish between the chip drivers.
BUG=b:169802515
BRANCH=zork
Change-Id: Ieac603a970cb2c9bf835021d1fb0fd07fd535280
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Pictures on the internet show that the Asrock H110M-DVS (Kconfig.name)
only has two DIMM slots. Since the vendor's website advertises support
for dual channel memory, drop the SPD addresses for the second slot of
each channel. The result is the same as several other two-slot boards.
Change-Id: I4b62e9196bfa3a688016399d7e025ca995f3c12c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The DQ and DQS byte maps do not apply to DDR4 configurations, and the
RCOMP resistor and target values are not correct for SKL-S (or KBL-S).
Drop the byte maps and use RCOMP values for the correct platform type.
RCOMP resistor values for all non-socketed platforms are listed in the
Platform Design Guide, and also appear in schematics. For SKL-S, the
RCOMP resistors are on the CPU and their values have been confirmed
by measuring them on an i5-6400, and match the PDG values for SKL-H.
RCOMP target values can be guessed from Intel Document #573387 and some
of them are also present in datasheet volume 1, under DC specifications.
Change-Id: I699d46b9b516be8946367e6d9b24883ae1e78d03
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Update Slot Designation strings and add SSD0_M2_Boot_Drive for config A.
TEST="dmidecode -t 9" to verify the results are expected.
Signed-off-by: Jingle Hsu <jingle_hsu@wiwynn.com>
Change-Id: I3fc03a14ff7dc43d6ddf5aa36710c99dbc648afa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
1. Add speaker amplifier ALC1015
2. Enable dmic+ssp registers for speaker and camera DMIC
3. Correct I2C#2 to LVDS, I2C#3 to Touchscreen
BUG=b:170273526
BRANCH=puff
TEST=Build and check DUT function status
Change-Id: I5f6f19b40c6fcce8dca9b010ae97ea6e3eeb1473
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46289
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove unused device in Dooly
no SD card reader
no built-in LAN
BUG=b:170273526
BRANCH=puff
TEST=Build and check DUT function status
Change-Id: I8ab1e156031bfb4d5ea30048d8a10400f2a49411
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Dooly has USBA*2 and USBC*2
BUG=b:170273526
BRANCH=puff
TEST=Build and check DUT function status
Change-Id: Icb66a8d5382ca9664e7f0b3660f446aeb3cf1dd3
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46126
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Override unused device
SD card reader, built-in LAN
ALC1015 speaker amplifier SPK_AMP_ON
Update touchscreen/lvds gpio pin
BUG=b:170273526
BRANCH=puff
TEST=Build and check DUT function status
Change-Id: Ife14adf59609870abe9f4ba1eabe2573cb6e92dd
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Change-Id: I6f4d0bf9adc1cce4942a16675a072ffea00bd2e0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
0x5 to 0x2
DSDT revision 2 is used for ACPI v2 and greater.
Change-Id: Ia019358be6574db1b2b06a8a7d52ae996cf45571
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Refer to commit d7b88dc (mb/google/x86-boards: Get rid of power button
device in coreboot)
This change gets rid of the generic hardware power button from all
intel mainboards and relies completely on the fixed hardware power
button.
Change-Id: I8f9d73048041d42d809750fdb52092f40ab8f11f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The DQ and DQS byte maps do not apply to DDR4 configurations, thus
simply drop them.
Also drop ECT, as it's already initialized to zero and can't be used on
DDR4 anyway.
Further, trim down all the meaningless and/or wrong comments.
Change-Id: I32f1b7bb46eaaf0f0ecad1df310f5de988f64c85
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46249
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop the disabled SPD indices from memcfg, since they're already
initialized to 0.
Change-Id: I6d88bdac17222c2c5c35439517fe0bea46744b2b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Drop USE_LEGACY_8254_TIMER, since it's not required anymore for
booting grub, despite the comment. The issue was resolved upstream
five years ago: http://git.savannah.gnu.org/cgit/grub.git/commit/?id=d43a5ee65143f384357fbfdcace4258e3537c214
Test:
- Boot EFI GRUB2 from TianoCore payload
(Debian Live, Ubuntu installer)
- Boot GRUB2 payload
Change-Id: I5ce4f5168586bf305969b2e24b6ee895c8552749
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45960
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The keyboard only works randomly, because SeaBIOS initializes PS/2
before the EC is ready.
Set the PS/2 timeout for SeaBIOS to 500 ms, to wait for the EC before
initializing the keyboard.
Test: keyboard works fine.
Change-Id: I2be75961035f04a7ffa6f7e1dbaabb1243b857f9
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45959
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPP_A19 and GPP_A20 set no connection, disables DdiPort1Hpd and DdiPort2Hpd
BUG=b:169690329
TEST=build and verify type-c(C0/C1) port functional normally
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I4405526ae777332d3c72041db7b4eda25ae31b8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46069
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: TH Lin <t.h_lin@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Refactor DPTF section of code under the baseboard devicetree
and overridetree. This makes override mechanism more simpler,
because not all the DPTF fields need to be overridden.
BUG=None
BRANCH=None
TEST=Built and tested on dedede system
Change-Id: I8e7cfe60c010ed4c07f9089325b289519e861f84
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
It builds same binary for ibase/mb899 using BUILD_TIMELESS=1
Change-Id: I947c4228641abc38a5cd75e51fa2f096fda95d6f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45280
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It builds same binary for intel/d945gclf using BUILD_TIMELESS=1
Change-Id: Ic48008719a9cf6942ae8cdaebaab6ba43e665489
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45281
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9f5a89946888be3ed033c2ee079f171a23404e90
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I6ddc3d0c50c5907e24644cea5979d064bea4acd1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45913
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Generated buils/dsdt.dsl for intel/kblrvp11 are same.
Change-Id: I41195be171b48f41fe2955e4639d8b770853d483
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46081
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Change-Id: I91f65fecdcdf41dc41f136e8d66bbf730343aef3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46078
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ie2b1b27c0715fc223e644c3df6c0e9cb876322c8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Generated 'build/dsdt.dsl' files are same.
Change-Id: I15b332033f3d492f9e01bb5f1eb25892dee418de
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Change-Id: I35dc4be65f0843c3c74695c443dd958676e6c12c
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Allow MRC training in SaGv low, mid and high frequencies.
TEST=Verify memory trains at low, mid and high SaGv point
through FSP debug logs enabled.
Change-Id: I0f60aad031ce9dfe23e54426753311c35db46c05
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45196
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix typo for power limit values under comment section in baseboard
BUG=None
BRANCH=None
TEST=Build for volteer system
Change-Id: I879b9587e863360bf4efda4099d96b42b904377e
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Tested on OCP deltalake. The console now shows up on the serial.
Change-Id: If4c412c1ca749f1feba47b2ce0beb52d0111be86
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
- This change is required to execute EC sync in coreboot instead
of depthcharge
Bug=none
Test=build and boot coreboot on TGLRVP
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I40ae104d4de93c12097e049253a33b23a46c6203
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44689
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Bug=none
Test=emerge build and boot on tglrvp and check that
tpm is probed successfully from coreboot.
Cq-Depend:chromium-review:1881839
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I4a3aec98f72524e8e2a1834878ef75b9f933ae3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
|
|
Add trackpad, touchscreen, and usb port to devicetree
BUG=b:160664447
BRANCH=NONE
TEST=build bios and verify theirs function for boten
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: I057f7d15d20d1a78acd733cc5463357e9c87afb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add SPD support for DDR4 memory part H5ANAG6NCJR-XNC.
Eldrid should use DRAM_ID strap ID 4 (0100) on SKUs populated
with H5ANAG6NCJR-XNC DDR4 memory parts.
BUG=b:161772961
TEST="FW_NAME=eldrid emerge-volteer coreboot" and verify it builds
successfully.
Change-Id: Ia26315479ce1a749a0f7c9e81f134f7068d7eb0b
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=Boot dirinboz, run integrity test, b:169940185
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I6bac8284b67070ff2c5838257f4ae2ead0e69c22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45934
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=WIP
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I1191d73a2a3f72f99de187a946162460acbb287a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45935
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=WIP
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I2fcbe35103020c3444902c077b4985f87f970671
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45936
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=Boot on Vilboz with emmc
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I9a1e47dbee3fcc7317857d40c5418be30d755d61
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45933
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ethernet hardware on jecht variants doesn't support AER, so
disable it to mitigate continuous AER timeout errors in dmesg:
> pcieport 0000:00:1c.0: AER: Corrected error received: 0000:00:1c.0
> pcieport 0000:00:1c.0: AER: PCIe Bus Error: severity=Corrected, type=Data Link Layer, (Transmitter ID)
> pcieport 0000:00:1c.0: AER: device [8086:9c94] error status/mask=00001000/00002000
> pcieport 0000:00:1c.0: AER: [12] Timeout
Change-Id: Ieda82c6e13c2bbc4b3a051a3d2a7ae90728ccdc6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46137
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ethernet hardware on beltino variants doesn't support AER, so
disable it to mitigate continuous AER timeout errors in dmesg:
> pcieport 0000:00:1c.0: AER: Corrected error received: 0000:00:1c.0
> pcieport 0000:00:1c.0: AER: PCIe Bus Error: severity=Corrected, type=Data Link Layer, (Transmitter ID)
> pcieport 0000:00:1c.0: AER: device [8086:9c94] error status/mask=00001000/00002000
> pcieport 0000:00:1c.0: AER: [12] Timeout
Change-Id: I0f592a21d08e79cda251e80cd1f1184c4311e9df
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46136
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A SATA drive may be connected to SATA0.
BUG=b:162909831
BRANCH=puff
TEST=none
Change-Id: I2a4ce2f89fa6d786358e01add15f2eedfbe4b20f
Signed-off-by: Sam McNally <sammc@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
List of changes:
1. Add DDR4 and LPDDR4 memory related code
- SPD for LPDDR4
- DQ byte map
- DQS CPU-DRAM map
- Rcomp resistor
- Rcomp target
2. Fill FSP-M related UPD parameters
3. Add devicetree.cb config parameters related to FSP-M UPD
TEST=Able to build and boot ADL-P RVP till ramstage early
Change-Id: Iffc5c17ed0725f61c8c274a80a1d27161ca6cebf
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change drops maxsleep parameter from chip config and instead
hardcodes the deepest sleep state from which the WiFi device can wake
the system up from to SLP_TYP_S3. This is similar to how other device
drivers in coreboot report _PRW property in ACPI. It relieves the
users from adding another register attribute to devicetree since all
mainboards configure the same value. If this changes in the future, it
should be easy to bring the maxsleep config parameter back.
BUG=b:169802515
BRANCH=zork
Change-Id: I42131fced008da0d51f0f777b7f2d99deaf68827
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Use the device aliases provided by tigerlake chipset.cb instead of
the raw pci device+function. Take advantage of the default states
in chipset.cb and only list the devices that are enabled for all
volteer variants.
Change-Id: I5620004afd7fa4d50389f32dd79148960a2b2662
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44039
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, trogdor devices have a section RO_DDR_TRAINING that is used
to store memory training data. Changing so that we reuse the same
mrc_cache API as x86 platforms. This requires renaming
RW_DDR_TRAINING to RW_MRC_CACHE and removing RO_DDR_TRAINING in the
fmap table.
BUG=b:150502246
BRANCH=None
TEST=FW_NAME="lazor" emerge-trogdor coreboot chromeos-bootimage
Make sure that first boot after flashing does memory training
and next boot does not.
Boot into recovery two consecutive times and make sure memory
training occurs on both boots.
Change-Id: I16d429119563707123d538738348c7c4985b7b52
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
1. Apply the DPTF parameters received from the thermal team.
BUG=b:169183507
TEST=build and verify by thermal tool
Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com>
Change-Id: I1a1a0f9e86e519ac15904fac80cf3c2299213e52
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
If Cr50 is running old firmware version and hence does not ensure long
interrupt pulses, override the GPIO PM configuration.
BUG=None
TEST=Build and boot waddledee to OS. Ensure that any chip override
happens before FSP silicon parameter initialization. Ensure that the
suspend/resume sequence works fine. Ensure that the reboot sequence
works fine for 50 iterations.
Change-Id: I455c51d4a63b1b5edadbf00c786ce61b0ba1ff00
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
ALS is not stuffed in octopus boards. Hence disable ALS ACPI devices.
BUG=b:169245831
BRANCH=octopus
TEST=Ensure that ALS devices are disabled in ACPI tables.
Change-Id: I5ad28f01b0515a41b314116eb2d05c520df0f86e
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=Boot Berknip w/ eMMC to OS.
BRANCH=zork
Change-Id: I5d55f55b8208b4dc3fbdc9d1ec6333f9e211e3fd
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45931
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Current Ram_Id: 0011 MT40A1G16KNR-075-E never be built before.
Remove it and change use micron-MT40A1G16KD-062E-E for ram_id:0011.
BRANCH=zork
BUG=b:159316110
TEST=run gen_part_id then check the generated files.
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Change-Id: I28fc39f17e06ecd39f6567613e6ff5919becb2fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45810
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=Boot Ezkinil w/ eMMC to OS.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ida0bbf9bd772ab7d384d5d097fa3b02b846a3efa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45852
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=Boot on morphius with and without patch, confirm ~7ms improvement
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I7f6efd3d5839f154f2487a07654be8e35634bbbc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45932
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update TSR1 passive trip temperature
BUG=b:169691800
BRANCH=None
TEST=Built and tested on dedede system
Change-Id: I172391daca981d5591fa9cc5eacad92521dd0dc5
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
BUG=b:167472333
TEST=Build and boot dedede and observe the slope and offset values
getting updated in the fsp debug log
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I3ea32218040263f0abef9b9dd4c52efb16289fd7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45825
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Implement mainboard_silicon_init_params() to allow for disabling of
TBT root ports if the device does not have usb4 hardware.
Add code to mainboard_memory_init_params() to disable memory-related
settings associated with TBT in cases where no usb4 is available.
BUG=b:167983038
TEST=none
Change-Id: Iab23c07e15f754ca807f128b9edad7fdc9a44b9d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Override smbios_fill_dimm_locator for type 17 Locator and Bank Locator.
Also remove CONFIG(GENERATE_SMBIOS_TABLES) compile option because SMBIOS
is always enabled and it makes the code cleaner.
One sample type 17 table displayed as below:
Handle 0x0010, DMI type 17, 40 bytes
Memory Device
...
Locator: DIMM F0
Bank Locator: _Node0_Channel5_Dimm0
Tested=On OCP Delta Lake, the Locator and Bank Locator strings
are expected.
Change-Id: I84531f9ee8bc76d9529aa983bc13e64f40c93138
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Rename all mt_pll_raise_ca53_freq() into mt_pll_raise_little_cpu_freq().
Implement mt_pll_raise_little_cpu_freq() in MT8192.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Change-Id: I97d9a61f39f2eb27f0c6f911a9199bf0eaae4fbe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
List of changes:
1. Initial code block to select SOC_INTEL_ALDERLAKE Kconfig
2. Add minimum code to make ADL-P RVP build successfully
3. Mainly bootblock and verstage code added to reach till verstage
4. Add support for 2 mainboards as ADL-P board with default EC (Windows
SKU) and Chrome EC (Chrome SKU)
5. Add empty dsdt.asl to avoid compilation error
TEST=Able to build and boot ADL-P RVP till romstage early.
Change-Id: I2b551f48a4eb4d621d9a86c5d189c517d5610069
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
TEST=Able to build TGLRVP and JSLRVP.
Change-Id: Ie07df9f59015092a4c2a27b1451f0d556c70f0d8
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
To remove the xhci0_force_gen1 and use usb3_port_force_gen1 instead.
The xhci0_force_gen1 is used for force all port on xhci0 to USB3 GEN1.
Now variant can use the usb3_port_force_gen1 to customize which port
it needs to limit.
BUG=b:167651308
BRANCH=zork
TEST=Build, verify the USB3 speed in gen1
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: If5f0c1f22d8c98c4461f09d074bf082c340b14d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
In morphius, the USB3 typeA port needs to set to gen1, and for ezkinil
all the USB3 ports should force to gen1. So set the corresponding
setting to usb3_port_force_gen1 to force USB3 to Gen1.
BUG=b:167651308
BRANCH=zork
TEST=Build, verify the USB3 speed in gen1
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I10419b91fe86fe3e06de36ddfe0d1769c1031f8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Id913fc4a89ad5eff6b3487354ff8be7661539fe5
Signed-off-by: Manideep Kurumella <mkurumel@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add support for trackpoint wakeup from S3 by adding device events to
mainboard and defining for morphius.
BUG=b:160345665
BRANCH=zork
TEST=tested trackpoint wake from S3 on morphius DVT
Signed-off-by: Josie Nordrum <josienordrum@google.com>
Change-Id: I982f0f4b60fbaeb389774531e1dee83da77cb8a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Adjust Touchscreen delay off values to let suspend off timing match
power down specificatiion.
BRANCH=zork
BUG=b:163434386
TEST=Measuring scope timing
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Change-Id: I58866122f441cc3c427e659b8a5fdb6643987882
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
This patch makes Fleex EC wake up AP from s0ix when the state of
charge drops to 5%.
Demonstrated as follows:
1. Boot Fleex.
2. Run powerd_dbus_suspend.
3. On EC, run battfake 5.
4. System resumes.
BUG=b:163721887
BRANCH=Octopus
TEST=Verified on Fleex:
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Change-Id: I4a998ad0aef5a7cfc6fd18995bde5571e6127e77
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Enable CHROMEOS_DRAM_PART_NUMBER_IN_CBI on hatch, dedede, and volteer
to use the common version of mainboard_get_dram_part_num().
Remove duplicate instances of mainboard_get_dram_part_num().
BUG=b:169789558, b:168724473
TEST="emerge-volteer coreboot && emerge-hatch coreboot &&
emerge-dedede coreboot" and verify it builds.
Change-Id: I4e29d3e7ef0f3370eab9a6996a5c4a21a636b40e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45883
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change mainboard_get_dram_part_num() to return a constant character
pointer to a null-terminated C string and to take no input
parameters. This also addresses the issue that different SOCs and
motherboards were using different definitions for
mainboard_get_dram_part_num by consolidating to a single definition.
BUG=b:169774661, b:168724473
TEST="emerge-volteer coreboot && emerge-dedede coreboot && emerge-hatch
coreboot" and verify build completes successfully.
Change-Id: Ie7664eab65a2b9e25b7853bf68baf2525b040487
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45873
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable eMMC with HS200 mode for mc_apl6 mainboard.
TEST: Linux booted and checked with 'lspci'.
Change-Id: Ib760a1a26a92047e8916979ffb5001bcff0a6e45
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45898
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch moves platform.asl into common block acpi directory to
avoid duplicating the same ASL code block across SoC directory.
TEST=Able to build and boot TGL, CNL and CML platform.
1) Dump and disassemble DSDT, verify _PIC method present inside
common platform.asl is still there.
2) Verify no ACPI error seen while running 'dmesg` from console.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I5189b03d6abfaec39882d28b40a9bfa002128be3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Delete SoC local copy of ipu.asl and refer from common block ipu.asl
TEST=Dump and disassemble DSDT on tglrvp, verify IPU0 device
present there.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I6a0f8a919092f7bbcd64d4791746d30fdee33894
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45978
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Move and use the common xeon_sp/cpx/acpi asl for skx/.
There were only minor whitespace differences between the directories.
Update the mainboards to build the moved files.
TiogaPass coreboot.rom checked with BUILD_TIMELESS.
Change-Id: I5058a3fe8d96075a266fb92f10707bb94308c85b
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45217
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
While restructuring the mainboard directory, it was forgotten to add the
variant specific romstage.c to the build. Therefore, add romstage.c to
the Makefile fixing the raminit.
Change-Id: I7afbf1574803128f7d62592eed2398c945334757
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45928
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
displays for TGL-Y RVP
- Enable DDC pins for DDI-B
- Enable HPD pins for DDI-1/DDI-2
- Update MPHY/USB2 Mapping to match with the TGL-Y RVP schematic
BUG: System not able to detect displays attached to onboard micro-HDMI or Type-C connectors
TEST: hot-plug/unplug HDMI displays with onboard micro-HDMI connector and USB Type-C connectors to make sure the displays get detected and enabled
Change-Id: I08a1b16a8fa45cf0f366661395b9f2aa25c44935
Signed-off-by: Jason Le <jason.v.le@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Configure EMMC_RESET_L (GPIO68) to drive high by default. As per JEDEC
specification for eMMC, RST_n_FUNCTION defaults to temporarily disable
reset using RST_n signal (which is connected to EMMC_RESET_L on
zork). Chrome OS platforms do not configure RST_n_FUNCTION thus making
the reset signal unused. The spec also says that there are no internal
pulls on the card and hence the RST_n signal should be driven
appropriately to prevent the input circuits from flowing unnecessary
leakage current.
Thus, even though the line remains unused, since it is connected in
hardware, this change drives EMMC_RESET_L to high.
BUG=b:169222156
BRANCH=zork
TEST=emerge-zork coreboot
eMMC DUT reboot/suspend x100 iterations pass
Change-Id: I9feb826eec8a8cdad5e2bd7efcbb1dcf96185dfd
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Change-Id: Idcaedd3d5b7e465644f79e5a882e42eff040fdbd
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
This fix needs to go into ACPI in the long-term, but this
should suffice in the short-term.
BUG=b:158087989
TEST=Boot berknip, verify backlight is enabled. Test suspend
& resume sequence, backlight is still enabled.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I6ecc3c9e397c9756a78e480d3f639c507879a0ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45854
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SMU code was assuming that GPIO 85 was used for a fan, which caused
interesting backlight flickering. That has now been fixed, so remove
the code that reconfigured it to a GPIO on resume.
BUG=b:155667589
TEST=Verify the screen does not flicker on resume from S3
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I6d4f9d98e9df52fefab9b20d0ab0f0b67512d356
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Even though the devicetrees of Mandolin and Cereme are relatively
similar, they are kept as separate files instead of using devicetree
overrides to facilitate creating mainboard ports based on those CRBs.
The two boards are reference boards for different zen/zen+ APU platforms
that share the silicon, but use different packages. This is also
consistent with the google/zork boards that have two different full base
devicetrees for the two different platforms and then use devicetree
overrides for the different variants of the two reference designs.
BUG=b:159617786,b:169644059
BRANCH=zork
Change-Id: Ief8a05b0a360563d26a81941720b78014feb0d25
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42786
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With this change the flash addresses will only get transferred over one
data pin like in the non-quad SPI mode and only the data will get sent
over all four data pins. Since this gives the flash chip a bit more time
to fetch the data the host requested, this allows higher SPI frequencies
resulting in a higher throughput when bigger chunks of memory get read.
BRANCH=zork
Change-Id: Iad4c922ffcdba4b17e6e81244ff37302eb171d97
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45831
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This fixes the board not booting reliably when running from flash
without the EM100 option selected during build time. Selecting EM100
mode overrides the settings, so when testing with an EM100 I didn't run
into this issue.
BUG=b:169644059
BRANCH=zork
Change-Id: I2c7043c174dcf4501776a03b7689d8a20c214afb
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45830
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Matt Papageorge <matthewpapa07@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch updates the SLP_Sx assertion widths and power cycle duration
for volteer.
Power cycle duration:
With default value,
S0->S5 -> [ ~4.2 seconds delay ] -> S5->S0
With value set to 1,
S0->S5 -> [ ~1.2 seconds delay ] -> S5->S0
BUG=b:159108661
TEST=Verified that the power cycle duration is 1~2s with a global reset
on volteer.
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Change-Id: Idf4e0c3a60b4ac59e31df1357f2ff28f195ff17f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
Remove these comments, because they do not contain useful information
that helps to understand the circuit, which we do not have.
Change-Id: I8a994a6f27d830bd05819043336d12c2ecef2f48
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45371
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Converts bit fields macros to target PAD_CFG_*() macros. To do this,
the following command was used:
./intelp2m -n -t 1 -file ../../src/mainboard/51nb/x210/gpio.h
This is part of the patch set
"mb/51nb/x210/gpio: Rewrite pad config using intelp2m":
CB:43566 - 1/4 Decode raw register values
CB:43567 - 2/4 Exclude fields for PAD_CFG
CB:43568 - 3/4 Fixes PAD_RESET to convert to PAD_NC()
CB:43410 - 4/4 Convert field macros to PAD_CFG
Tested with BUILD_TIMELESS=1, 51NB-X210, remains identical.
Change-Id: I18c0c321561eee04ff927681b0a231f6d79c63e2
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43410
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
To get the HDA verbs from the OEM firmware, open the firmware with
UEFITool, search for the existing HDA verbs, extract the UEFI module
and look for the verbs. Copy the consecutive 4 dword sets that look
like HDA verbs.
It is tested to make audio output from both the speaker and headphone
work.
Change-Id: Ie359fdf6785b1c0be8dc201cd76176c0a7fe7942
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45693
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Id8b7d3776ab2cc8c487095273582cd013241bd3a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
We store the remainder in Local0, but we never use it.
Change-Id: I4d209d7434508cb626aca8e7df50cc1c424e294a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
1. TSRO trip point from 75C change to 73C
2. Sample period time from 5s change to 60s
BUG=b:160385395
BRANCH=puff
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I0b000841845ce793be0e52fc28a07ac6a931ef7a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
The default GPIO values for camera power were set as 1 so the LED was
turned on by default when the board is powered on.
This status is kept until the camera is probed then being turned off.
So the LED is turned on for a few seconds during the boot up.
By setting the default power to 0, the LED is lit only when camera
is turned on for probing and this should be just a blink.
BUG=b:167635396
BRANCH=none
TEST=Build and boot volteer board. Monitor camera privacy LED
and check it is not lit more than 0.5 seconds.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Ic7df391aa512daafe6e1ce49e9222b90e17ad806
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45058
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure overridetree settings for audio function.
BUG=b:153680359, b:163382106
TEST=FW_NAME=halvor emerge-volteer coreboot chromeos-bootimage
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I107f6fc21b99d80d69931139dc50e7d5873a8e52
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
cameras
There is a patch https://lkml.org/lkml/2020/9/3/235 which allows i2c
device can support driver probe without power up the device.
In order to support this, need add coreboot add
"i2c-allow-low-power-probe" property.
BUG=b:169058784
BRANCH=none
TEST=Build and boot volteer board. Monitor camera privacy LED
and check it blinks. It should not blink.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I46f90ff8d412b18c7ee4bd7f22f9a7db771eb84f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
