| Age | Commit message (Collapse) | Author |
|---|
|
Move the `GWAK` method into the GPIO device, and have lpc.c include the
LP GPIO code. All usages of `GWAK` on mainboards need to be updated.
Change-Id: Id6a41f553d133f960de8b232205ed43b832a83d2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46775
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These add nothing useful to the GPIO config
Change-Id: Ieecc9bd67d020e141c3a1f1d387034df5e563068
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47190
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update GPIO config using a fresh dump of inteltool from the
vendor (AMI) firmware on a Librem Mini v2, run through intelp2m
with parameters '-p cnl -n -ii'
Change-Id: I747415fb9ab7b21943d256d248729cb9e2b4b945
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47206
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Id306100fc691dcbde48b65092d0be9d7e73c0722
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47189
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move registers under devices to which they belong.
Change-Id: I61ca7c1db02646252d7421f8b79dfc8a40b2bdb5
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47188
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
this should have been corrected as part of:
commit 3de90d1 [soc/intel/cnl: Set Heci1Disable depending on devicetree config]
Change-Id: I6a103a1de01fc258ef359258a8a64f4c5a181139
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47187
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PL2 was set artificially low during development when the active cooling
fan was not functional, and never corrected once the fan was fixed.
Raise PL2 to a value which works with both Librem Mini variants.
Change-Id: Ie377392020f73359aed80ddae727adb6f8d06344
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
All chip registers default to 0, no need to explicitly set them.
Change-Id: I056121170d22393484b0ee79bd0815452161a900
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Not needed for this board.
Change-Id: I15a68b59bc512e571b9590007ea64561b3f3dae1
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Generated 'build/dsdt.dsl' files are identical.
Change-Id: I7ad79a31142af8ae1b62497ade0b4ba7bac3a93c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46214
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Generated build/dsdt.dsl files are same.
Change-Id: I5bd8fe629fb969ec14dd400b6463ee1592d6903b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46207
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Generated build/dsdt.dsl files are identical.
Change-Id: Iffd6954dcb3f9fb8bcd89854d84f6944cb520dd1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46208
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Generated 'build/dsdt.dsl' files are same.
Change-Id: I0eda144f1a4f07ca82b3a799afcd8fc908419e69
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46215
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Generated 'build/dsdt.dsl' files are identical.
Change-Id: I2eea24db6cfd260e0f36243e90a5e01b360f23fb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Generated 'dsdt.dsl' files are identical.
Change-Id: I7d4fc3acd82023b007d80638bcb71476330ef320
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Built google/beltino (Monroe) provides identical 'dsdt.dsl'.
Change-Id: I12b6a8264e53ece30ae79da2d79c6f1d302fb357
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Generated 'dsdt.dsl' files are identical.
Change-Id: I5897397bdadf86214ceaf90d8cd706e10969d8c1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Update dq/dqs mappings based on voema schematics.
BUG=b:169356808
BRANCH=volteer
TEST=FW_NAME=voema emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I1aae4286278e712bf29ebb15738477828d3f74d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I3a3d187fc24ab752dfe61893c15561a92d009fe2
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46062
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Generated 'build/dsdt.dsl' files are identical.
Change-Id: Idd2bf447975b4c9b2cd3b440505c0bd960374165
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Generated 'build/dsdt.dsl' are identical.
Change-Id: Ifed93f4b0c360ec74f28926fb7cc9774ae03b8a6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45555
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
"If(And(RFDV, 0x02)) {Or(Local0, 0x02, Local0)}" is duplicated.
Change-Id: I91698fb308cd37c65aa65e563bcd88743097f56c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45865
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The romstage region is moved up a bit more to satisfy the MMU.
Change-Id: I00c2b4972495fa669d4dc2a52f298a0e4d0cf5ff
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47105
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This CL is entirely generated by running the automatic formatter on this
one file.
BUG=None
TEST=abuild -t GOOGLE_VOLTEER2 -c max -x
Change-Id: Ibdd8cc2222e7af11c11df963b088ca2db07a3214
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Prevent early throttling when the ambient temperature is high.
Change-Id: Ie6881c9c0942aae3e43509170352271a74244d42
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change adds the callback
`elog_gsmi_cb_mainboard_log_wake_source()` to volteer to enable
logging of EC events in case of S0ix resume.
BUG=b:172272078
BRANCH=volteer
TEST=Verified that EC events are logged correctly for S0ix resume:
11 | 2020-11-02 14:11:05 | S0ix Enter
12 | 2020-11-02 14:11:08 | S0ix Exit
13 | 2020-11-02 14:11:08 | Wake Source | Power Button | 0
14 | 2020-11-02 14:11:08 | EC Event | Power Button
15 | 2020-11-02 14:11:17 | S0ix Enter
16 | 2020-11-02 14:11:21 | S0ix Exit
17 | 2020-11-02 14:11:21 | Wake Source | GPE # | 112
18 | 2020-11-02 14:11:21 | EC Event | Lid Open
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I7aa9dc2470da3226925927f2a0cc39fdd426e3b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47142
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
Change-Id: I7f87085c70149d02c544e2d43e1bdb58c7502d6d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46754
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Move the SoC select to board config (vs baseboard config)
- Qualify the VGA PCI ID and CBFS size values based on board selection
- Move devicetree to variant dir and add Kconfig entry
- Use a separate board_info.txt for the baseboard and each variant
Change-Id: I4764f2c1243ea49bd08e0735865cc3cb7a66441f
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Since Whiskeylake SoC code is actually a subset of soc/intel/cannonlake,
rename the baseboard so that boards using other 'cannonlake family' SoCs
(e.g., Cometlake) can be added with minimal confusion.
Rename the mainboard dir and baseboard name, and adjust any references
to them.
Change-Id: I2af7977f1622070eb8bf8449bc8306f9d75b9851
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
SCONFIG complains because of the duplicate devicetree entry.
Change-Id: Ibdd60efdbcee5bda7c570d4b98f29cc8ede584cb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jes Klinke <jbk@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add the USB ports to the devicetree for describing them in ACPI,
including defining the port relationships and defining the reset
GPIO for the bluetooth device.
BUG=b:151731851
TEST=tested on volteer, all other boards were checked against the
latest available schematic.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: Ia1e5b71e7750a478ff79372c48616bbf5c21b79c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Define option value 6 for DB_USB where there is a Type-A port but
no Type-C port on the daughterboard.
BUG=b:151731851
TEST=build volteer boards
Change-Id: I489d24316556dedfecd821e502f1461010b1400f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The Kakadu project will be using eMCP board design.
BUG=b:171841122
TEST=Boots on chromebook Kakadu successfully.
Signed-off-by: Sunway <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I44668ce630758e49fbf2c6028f56c01f83ff08f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46871
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
variant_smi_sleep is called in smm stage so we need to add
variant.c into smm stage. Otherwise it will call the dummy one.
BUG=b:168075958
BRANCH=octopus
TEST=build image passed.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I41df1a30b119ab3e04f9ae01955b6044f137527f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46847
Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For development of the firmware to run on the Dauntless TPM, a number of
Volteer2 devices are being reworked to replace the H1 chip with probe
wires to connect to an external Dauntless development board.
Some modification to the AP firmware is required, not least because the
Dauntless chip is connected via I2C bus, instead of SPI. Most of the
Dauntless developers will not otherwise have a Chrome OS chroot.
Because of the above, I think it makes sense to have a new variant, for
the reworked devices, which I intend to create with this CL.
BUG=b:169526865
TEST=abuild -t GOOGLE_VOLTEER2_TI50 -c max -x
Change-Id: Ibdcd6c2ce3941c229518f21f0e479890b5d76dd1
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46437
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory part being added is:
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
H9HCNNNBKMMLXR-NEE
MT53E1G32D2NP-046 WT:A
K4UBE3D4AA-MGCR
BUG=b:169813211
TEST=Build the metaknight board.
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Change-Id: I0d0d22f4790f66b5265803e4dcf01234a16b1993
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable SaGv for terrador.
BUG=b:171763116
BRANCH=volteer
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ie00166a619424a67f70f870e55822ae2cc6d023d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46841
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derek.huang@intel.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Change-Id: I5131cf350d5b8c2a45f8d8245c0df26742c0d732
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45533
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure board specific DPTF parameters for delbin
BUG=b:168958222
BRANCH=volteer
TEST=build and verify by thermal team
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I69aa6046fdc90a2cf59ea3a13fdb15c8bc0d29a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46676
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the voema variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:171755775
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_VOEMA
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I4e1872d1ebff6fefdfb232f1ff82fce95a1ec643
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47007
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add G2Touch touchscreen support for dood.
BUG=b:171526389
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage, and check touchscreen
work.
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: Ica7d893de285c2dd1efcd43ac74919bdd5d5ac17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46675
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ELAN touch support and update Goodix settings.
BUG=b:157265632
BRANCH=zork
TEST=emerge coreboot and check both touch screen are workable.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Icfc2421061e8b3163d7d5108673351bc17df20ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46929
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This change reorganizes the CNVi device entries in mainboard
devicetree/overridetree and SoC chipset tree to make it consistent
with how other SoC internal PCI devices are represented i.e. without a
chip driver around the SoC controller itself.
Before:
chip drivers/wifi/generic
register "wake" = "..."
device pci xx.y on end
end
After:
device pci xx.y on
chip drivers/wifi/generic
register "wake" = "..."
device generic 0 on end
end
end
Change-Id: I22660047a3afd5994400341de0ca461bbc0634e2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Terrador and Todor are fanless design, so disable DPTF active policy.
BUG=b:171019363,b:170699797
BRANCH=volteer
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I53a33b8706d7a7d4013a2a5627a620223fcffc3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46874
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO D4 was used for camera reset for both front and rear cameras
(RCAM_RST_L/FCAM_RST_L) in RIPTO. For later volteer versions,
GPIO F15 is dedicated to the rear camera reset (RCAM_RST_L).
Before, BOARD_GOOGLE_VOLTEER flag was used for setting the right
RCAM_RST_L per volteer version. However, we don't support RIPTO
anymore. Also using flags for different volteer version support can
be error-prone. Removing RIPTO support.
BUG=b:171726823
BRANCH=none
TEST=Build and boot volteer proto2 or later version. Camera should
work without an issue.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I961fc17092887b4807c12c95f7139bb7e7b33e91
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46826
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The min86 example SoC code along with the example mainboard
should serve as a minimal example how a buildable x86 SoC code
base can look like.
This can serve, for instance, as a basis to add new SoCs to
coreboot. Starting with a buildable commit should help with
the review of the actual code, and also avoid any regressions
when common coreboot code changes.
As the example code itself is build-tested, it should advance
with coreboot and can't rot like documentation might. It also
serves as a check what APIs need to be implemented with the
default Kconfig settings.
Change-Id: Id76ab15fe77ae3e405c43f9c8677694f178be112
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45710
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The camera privacy LED blinks during the boot and this gives a wrong
impression to the users that the camera is being used during the power
up. The blink happens when the camera module is probed and a series of
kernel patches and coreboot patches are being submitted to resolve the
issue.
The kernel patches are submitted to the chromium gerrit.
https://chromium-review.googlesource.com/2403386
https://chromium-review.googlesource.com/2403387
https://chromium-review.googlesource.com/2403385
https://chromium-review.googlesource.com/2403384
https://chromium-review.googlesource.com/2403383
https://chromium-review.googlesource.com/2403382
https://chromium-review.googlesource.com/2403381
https://chromium-review.googlesource.com/2403380
This is to separate the power resource for the VCM so that it can be
controlled by the driver and suppress the LED turn on.
BUG=b:169049942
BRANCH=none
TEST=Build and boot volteer board. Monitor camera privacy LED
and check if it blinks. It should not blink.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Id51c98e42c5f20e231d8096c9d2d98deebc7c968
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@google.com>
|
|
LTE module Fibocom L850-GL is lost after idle overnight,
with this workaround, host will not initiate U3 wakeup
at the same time with device, which will avoid the race condition.
If this option is set in the devicetree, the bits[7:4] in XHCI MMIO BAR +
offset 0x80A4 (PMCTRL_REG) will be updated from default 9 to 0.
BUG=b:169645448
BRANCH=octopus
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3a04320b0e2441dce540a5afdc461f12de45c41b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
|
|
We all knew this was coming, 32 bits is never enough. Doing this early
so that it doesn't affect too much code yet. Take care of every usage of
fw_config throughout the codebase so the conversion is all done at once.
BUG=b:169668368
TEST=Hacked up this code to OR 0x1_000_0000 with CBI-sourced FW_CONFIG
and verify the console print contained that bit.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6f2065d347eafa0ef7b346caeabdc3b626402092
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45939
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that soc_get_pmc_mux_device() is gone, the PMC MUX connector devices
can be hooked up together via devicetree aliases.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib51764da5b3c029f9ac7ac60199a0aedfc7f29b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45878
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current I2C5 bus frequency is 367 kHZ, which does not meet the spec.
This change updates scl_lcnt, scl_hcnt, scl_hcnt value for I2C5 to bring
the bus frequency closer to 400kHz.
BUG=b:153588771
TEST=Verified that I2C5 frequency is between 389-396kHz.
Signed-off-by: Johnny Li <johnny_li@wistron.corp-partner.google.com>
Change-Id: If0803a74ba9071acf15486ce4038261c1681a92f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Flesh out the PCH configuration into a separate chip. Keep it within the
Broadwell SoC directory for now, to ease moving files around. The boards
were prepared beforehand and the devicetrees require next to no changes.
Tested on out-of-tree Acer Aspire E5-573, still boots.
Change-Id: I28d948f3e6d85e669d12b29516d867c1d1ae9e1a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46700
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
`chip` entries are only hooked up via device nodes to the tree. A `chip`
without a `device` below it does nothing. To allow variants to override
SATA tuning parameters, ensure a device exists under the PCH chip scope.
Without this change, some variants would not properly override the SATA
tuning parameters after extracting the PCH parts into a different chip.
TEST=Sanity-check static.c and verify overridetrees override properly.
Change-Id: I013dbe1403567b93c8ee0e66f76481f2a3f42796
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46769
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, all variants remain identical.
Change-Id: I0fe6de35f7471ce173df40db1444153623544f00
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46705
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, coreboot.rom remains identical.
Change-Id: I75d6594f9576c96a585526c652a070cb9616dbe9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46704
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, all variants remain identical.
Change-Id: I0fa486b8a0fc8be974f37d0bb4eb77a254e8cd86
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46703
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:170604353
BRANCH=volteer
TEST=emerge-volteer coreboot, and boot into kernel.
Change-Id: If354aa158f3ad60193268f38278a44f9c99bf3db
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46770
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the ambassador variant of the puff reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:171561514
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_AMBASSADOR
Signed-off-by: Matt Ziegelbaum <ziegs@chromium.org>
Change-Id: Ib0e3a813a120a4a8e984f3a89dc3ba100d94da95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
List of changes:
1. Split mem_cfg for DDR4 and LPDDR4 as per board_id
2. Move dq_pins_interleaved into board-specific memory configuration
information
TEST=Able to build and boot DDR4 and LPDDR4 ADLRVP SKUs.
Change-Id: I6ef19209767c810426bba0c8bc48178bf2e2a110
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46873
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The LDNs don't have a 0x30 register to enable them. However,
with the devices set to `off`, coreboot won't configure them.
Change-Id: Iaea37c88524904a1dae8a6d3b5f07c6ea25bc3b2
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46021
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop useless writes to read-only registers and don't re-write
default 0x00 values. In detail:
* Don't write read-only status registers.
* Don't try to write input bits in data registers
(iow. mask data values: `data &= ~io`).
* Don't write data registers if all GPIOs are set as
inputs (`io == 0xff`).
* Don't write default 0x00 for inversion and multiplex
registers.
Note: Both GPIO0 and WDT1 values look spurious. Maybe they
were dumped with the virtual devices disabled?
Change-Id: I7d948d6b697285e61e4352b7354b924dbf511e9a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46020
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I8f5a87d006f8bf20af40f7a4f09b1e4b597ba79f
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46019
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It is enabled by the vendor firmware.
Also drop spurious `io 0x60 = 0x00` setting. It's the default anyway
and the resource is kept disabled (it's controlled by the virtual
LDN 2e.008).
This fixes the hang in `PCI: 00:14.3 init` when doing
`outb(0, DMA1_RESET_REG)`.
Fixes: 2f8192bc ("asus/f2a85m_pro: Fix superio type in devicetree")
Change-Id: I351c93033bf2afd824eb6baa8d7625e7a33a295a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I6a16e2f829219f2eba8acd3ae7f371238c0d8de1
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Remove code to turn on backlight during ACPI mode because backlight has
been properly enabled in ACPI.
BUG=b:158087989
BRANCH=Zork
TEST=tested backlight during reboot and suspend
Signed-off-by: Josie Nordrum <JosieNordrum@google.com>
Change-Id: I3bf06042aa19e4559127d611d401f0ba0516b3a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Generate acpi methods which enable and disable backlight during _INI,
_WAK, and _PTS.
BUG=b:158087989
BRANCH=Zork
TEST=check backlight during reboot and suspend
Signed-off-by: Josie Nordrum <JosieNordrum@google.com>
Change-Id: I2f3434dc92de1f697693ff69ca15bd76647b89a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46671
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add internal pull-down for GPP_D19 to improve DMIC noise issue on
nightfury.
BUG=b:171669255
BRANCH=firmware-hatch-12672.B
TEST=Built and checked GPP_D19 voltage after booting
Change-Id: Ie63f260be3d6a55f91908db59312b3b0a8af98f4
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The corresponding devices and objects are already included in the
System Bus ACPI scope inside uncore.asl. There is no need to do this
again in the DSDT of the motherboard.
Change-Id: I98a8d60b585e2eafd76948baea0f249a029bae09
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Rename motherboard_fill_fadt() to the common override
mainboard_fill_fadt() function to override FADT.
Tested=On OCP Delta Lake, verify FADT PM Profile is set to
Enterprise Server.
Signed-off-by: Jingle Hsu <jingle_hsu@wiwynn.com>
Change-Id: Ie9ea7cc6e712d0aca57bbeac1a4154921d123be4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
To support gpio reset SoC, we need to pass the reset gpio parameter to
BL31.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Change-Id: I2ae7684a61af76693605cc0bcf8d20c8992c7bff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46388
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The pins for SD and MMC must be configured properly
so we can access them in payloads.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: Ie6bdffb987d5acf286645550f1c53f294f71c38a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
LTE module Fibocom L850-GL is lost after idle overnight,
with this workaround, host will not initiate U3 wakeup
at the same time with device, which will avoid the race condition.
If this option is set in the devicetree, the bits[7:4] in XHCI MMIO BAR +
offset 0x80A4 (PMCTRL_REG) will be updated from default 9 to 0.
BUG=b:171478764
BRANCH=octopus
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Change-Id: I213fed2b56f216747b2727b69f97d46d8c0c872e
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46701
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
invoke LTE power off function to meet LTE power sequence while DUT is
in reboot state.
BUG=b:167565015
BRANCH=octopus
TEST=build and verify on the DUT with LTE
Change-Id: I825cefb524ddaf9a9cb6add31c2ee0eea484f978
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46022
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, all variants remain identical.
Change-Id: I2b088b36c8e9ff9cbd47d625b14fc45ebd96532a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46702
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:168783630
TEST=Measured the I2C bus frequency reduce to 387 KHz.
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: I9f5b81815f86db7bdcea95a95b9c9b235b4a34b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46613
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The LCM ID is not really used on Jacuzzi followers and the reference
design expects ADC to return 0. However, there were hardware design
issues so the returned value became unexpected numbers.
- Juniper and Kappa returns 1.
- Burnet and Esche returns 1 on normal boot, and 0 on recovery boot.
- Cerise and Stern usually returns 0, and sometimes 1.
To fix that, we are changing LCM ID to fixed value for Jacuzzi followers.
BUG=b:170916885,b:171365301
BRANCH=kukui
TEST=1. emerge-jacuzzi coreboot
2. check burnet/esche skuid correctly
Change-Id: I3b43b9153315ec65e9168c4e84ea844dff14d446
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
1. Enable dptf feature and remove fan control part from overridetree.cb
2. Update tcc offset to 5
3. Follow thermal validation and update PL2 max_power to 51
BUG=b:167931578, b:170357248
Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Change-Id: I99e429b90ed7de08385fe51ca742865b1266eef9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This reverts commit 214c719eed83967b8f0564feca65eebb3d83f5bc.
CB:45857 overrides the GPIO PM configuration if Cr50 does not support
long interrupt pulse width. More recent Cr50 Firmware versions support
long pulse width and hence the GPIO PM can take the default
configuration.
BUG=None
TEST=Build and boot Drawlat to OS. Ensured that 200 iterations of
suspend/resume sequence, warm and cold reboot cycles each are
successful.
Change-Id: I8e3be42cd82fd3ae919d23d6f19c84a90b9c737a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46652
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
Tested=On OCP Delta Lake, log level can be changed via VPD.
Change-Id: I36d4b01b6fb6acc726749641df089cb3f9a4dc3e
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
The dt option `speed_shift_enable` is obsolete now. Drop it.
Change-Id: I5ac3b8efe37aedd442962234478fcdce675bf105
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Enable front camera power in ramstage.
BUG=b:169170677
BRANCH=volteer
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I8b5a9a8333ed518883aa3664a115a4ba2e8a0218
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
Add goodix touch pad as below:
HWID : GXTP7288
CID : PNP0C50
I2C address : 0x2C
I2C speed : 400Khz
HID Descriptor Address : 0x20
BUG=b:171351666
BRANCH=octopus
TEST=build image and verify goodix touch pad working.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Idb4f8d3aff09712dcc98c8ae0c9ae30dc4049e29
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46614
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In deltalake, there's no embedded controller and BMC version is
used to represent ec version.
TEST=Build with CB:45138 and CB:46070
Execute "dmidecode -t 0" to check if the firmware version is correct
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I388efd749170f0ebbb4dd4d32199675d92cc018e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
New SKU ID 5 is used for LTE touch SKU. This patch does LTE power off
for LTE sku and only use Wifi SAR table for non-LTE sku.
BUG=b:168001586
BRANCH=octopus
TEST=Check no SAR table can be loaded with sku id 4 and 5.
Change-Id: Ic0405d3e52aa813bbb1f350966a9e2825e595ce4
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46643
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:161759253
BRANCH=firmware-zork-13434.B
TEST=emerge-zork coreboot chromeos-bootimage
firmware log:
\_SB.I2C2.SEMTECH SX9324: SAR Proximity Sensor at I2C: 02:28
kernel log:
INFO kernel: [ 11.238644] sx932x i2c-STH9324:00: initial compensation success
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I6294ce291365443dd1c4550ba75cb7f33481b889
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45565
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4077b9dfeeb2a9126c35bbdd3d14c52e55a5e87c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45404
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since google_chromeec_cbi_get_board_version and google_chromeec_cbi_get_fw_config both call cbi_get_unit32 and return 0 as success, non-zero as failure. Let's add more readability for the false condition.
BUG=None
TEST=check with empty CBI value
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia49ac1ee35302f8f6afe8c0eb8e13afdf36c5b2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46566
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use PCIE_CLK_NOTUSED in place of 0xFF for unused PCIe ports
BUG=none
BRANCH=master
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I35f2bbce35420fa98541a35f77b14df7440e7980
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
According to the schematic, SRCCLKREQ1# is not connected, so disable it
for terrador and todor.
BUG=b:171278849
BRANCH=volteer
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I5f7734d64390bfadbdb8d152261103adb8e75f40
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
According to the schematic,SRCCLKREQ1# is not connected,so disable it
on voxel.
BUG=b:171279034
BRANCH=volteer
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ibc4f766bd737f30a9ac3c7354d54398e0c36d59d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46612
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Asurada EC is using the large packet (256B) mode, and we were
seeing lots of timeout errors on various commands.
The AcceptTimeoutUs in EC SPI driver is hard-coded at 5000,
and that is too small for large packet running in 1M so we
should change EC SPI to the same value that kernel is using (3M).
BUG=b:161509047
TEST=emerge-asurada coreboot chromeos-bootimage; flash and boot
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Change-Id: I9c47324022129ca23ef75d0c80e215da1692636d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46394
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adding the blank line reduces the differences with the variant
toucan-af.
Change-Id: I58bfc99109a2df2eab54a562dc13e7bd946890d9
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46716
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: If1d4128055a0fd50d109b4aa04c7d0c8ebb2f6c5
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: If58d87296ed6fb176d4bc42ba6f6f39ca069adfd
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Enhance USB 2.0 C0/C1 A0/A1 SI by increasing the level of
"HS DC Voltage Level" and " Disconnect Threshold Adjustment" registers.
COMPDISTUNE0: 0x3->0x7
TXVREFTUNE0: 0x6->0xf
BUG=b:166398726
BRANCH=zork
TEST=1. emerge-zork coreboot
2. check U2 register is set correctly.
3. U2 SI all pass
Change-Id: I69d942605c6d43ece0d71f67df3a5e00b998219b
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46545
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable acoustic noise mitgation for volteer platforms.
BUG=b:153015585
BRANCH=none
TEST= Measure the change in noise level by changing the values
in devicetree.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: I69a6453091bf607d3c5847c99bc077e6b7dbc639
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45053
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the two load line slope settings for the SVID3 telemetry.
AGESA sends these values to the SMU, which accepts them as units
of current. Proper calibration is determined by the AMD SDLE tool
and the Stardust test.
VDD Slope: 62852 -> 62641
SOC Slope: 28022 -> 28333
BUG=b:170531252
BRANCH=zork
TEST=1. emerge-zork coreboot
2. pass AMD SDLE/Stardust test
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: Id831907aa47be27fef2e33bb884a1118ffec14a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The disconnect voltage needs to be adjusted up because the HS DC voltage
level is 0xF.
BUG=b:170879690
TEST=Servo_v4 USB hub functions
BRANCH=zork
Change-Id: If8662015a45c57e457b4593e55af888084842f58
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
RW_LEGACY region needs to be 1 MiB to accommodate any alternate
firmware. Hence update the flash ROM layout as below:
* Grab ~512 KiB from each FW_MAIN_A/B regions and allocate them to
RW_LEGACY region so that it grows to 1 MiB.
* Remove VBLOCK_DEV region which is not used.
* Re-size the ELOG region to 4 KiB since that is the maximum size of the
ELOG mirror buffer.
* Resize RW_NVRAM, VBLOCK_A/B regions to 8 KiB since no more than that
size is used in those regions.
* Resize SHARED_DATA region to 4 KiB since no more than that size is
used in that region.
* Based on the resizing, allocate each FW_MAIN_A/B regions with 72 KiB.
BUG=b:167943992, b:167498108
TEST=Build and boot to OS in Drawlat. Ensure that the firmware test
setup and flash map test are successful. Ensure that the event logs are
synced properly between reboots. Ensure that the suspend/resume sequence
is working fine. Ensure that the ChromeOS firmware update completes
successfully for the boot image with updated flash map and the system
boots fine after the update.
Change-Id: I53ada5ac3bd73bea50f4dd4dd352556f1eda7838
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46569
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To support mipi WFC.
1. enable DRIVERS_INTEL_MIPI_CAMERA/SOC_INTEL_COMMON_BLOCK_IPU
2. add IPU/VCM/NVM/CAM1 in devicetree
BUG=b:163879470, b:171258890, b:170936728, b:167938257
TEST=Build and boot to OS. Capture frames using camera app.
Change-Id: I96f2ef682dff851d7788c2b612765a92228ddf75
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44939
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Andy Yeh <andy.yeh@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
