| Age | Commit message (Collapse) | Author |
|---|
|
According to issue tracker b:119238959 #4 & #6.
Hardware modify design to make GPP_E3 to be a switch of touchscreen
I2C CLK and SDA.
Control GPP_E3 to make touchscreen I2C CLK and SDA keep low during
power on initialization to avoid data transfer during this time.
After touchscreen IC initial complete, control GPP_E3 to high to
make touchscreen I2C CLK and SDA work normally.
Depending on touchscreen IC specification, device take 105ms for
power on initialization.
Change delay time from 120ms to 105ms.
BUG=b:119238959
BRANCH=firmware-rammus-11275.B
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, run S5 stress test and verify the result
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I86452c1445243c499aeaf931dba286db169c5628
Reviewed-on: https://review.coreboot.org/c/30180
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3b9217a7d9a6d98a9c5e8b69fe64c260b537bb64
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable SPI controller(D31:F5).
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: I4d3acd3f31650d5b39927f8e3cfbb6187541653f
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/30438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
This patch incorporates following changes to enable console on UART0
1. update default console number to 0
2. Enable PCI port for UART0
GPIO configuration will be done by coreboot based on correct console
number.
Change-Id: I735d33674b276b28e2cbb753d3a6d83edbabe89d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Enable LPC/eSPI controller(D31:F0). EC would be using
eSPI interface, since the strap GPP_C5 is pulled up.
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: Ia4baf80a775ba8898055f82e80dc583e65c4ed0b
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Add SMI handlers for below SMI events:
1. eSPI SMI event.
2. ACPI enable/disable SMI event
-> Add support for EC to configure SMI mask on ACPI disable.
-> Add support for EC to configure SCI mask on ACPI enable.
3. Sleep(S3/S5) SMI event
-> Add support for EC to configure wake mask for S3/S5 event
Change-Id: I7127b44712cd89b3d583e9948698870ca0c64b2b
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Adding hot plug detect GPIO support for external Type-C display in event for
cable connect/disconnect.
Change-Id: If9d52dc0f9916f761c8fdd88c76968aaf663e650
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30365
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch modifies the hatch flash layout to support
IFWI 1.6 with the following regions,
Flash Region 0: Descriptor
[0x0 - 0xFFF]
Flash Region 1: IFWI (consist of ME and PMC FW)
[0x1000 - 0x3FFFFF]
Flash Region 2: BIOS
[0x1400000 - 0x1FFFFFF]
Change-Id: I3d05fb50e970737a2552b85d6aebed943bf2b6cb
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30413
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable EC LPC interface and configure below LPC IO decode ranges:
1. 0x200-020F: EC host command range.
2. 0x800-0x8FF: EC host command args and params.
3. 0x900-0x9ff: EC memory map range.
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: Ie5d92df80d6b3a5913d0cbe78c1b8eefb5269d4a
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This implementation adds below code:
1. Add SOC ACPI code in dsdt.asl
-> platform.asl
-> globalnvs.asl
-> cpu.asl
-> northbridge.asl
-> southbridge.asl
-> sleepstate.asl
2. Add chromeos.asl in dsdt.asl
3. Add EC ACPI code in dsdt.asl
-> superio.asl
-> ec.asl
4. Remove config for WAK/PTS ACPI method as chromeec
doesn't implement those.
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: Icf1b1d7e34a7e863139c3583903f3b1e2cdc8da6
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This implemetation adds EC SCI, SMI, S5/S3 wake trigger events.
Also adds the EC specific ACPI configs to enable support for ALS,
EC PD device and PS2 keyboard device.
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: I3a86f609c269cb59e546fc7ba4ba032e5ea8341a
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30281
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mainboard has the BSEL straps hooked up to the SuperIO
similar to the ASUS P5GC-MX and might therefore require a restart.
Tested:
- FSB 800, 1067 and 1333MHz CPUs
- USB
- Ethernet
- Serial
- 2 DIMM slots
- SATA
- Libgfxinit (VGA)
TESTED with SeaBIOS (sercon disabled) and Linux 4.19.
Change-Id: Id845289081751ff8900e366592745f16d96f07c0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Any board that uses the AST driver will have support for native graphics
init. So, select the option in the driver instead of every board.
Change-Id: I2bf42c168d1ffdda11857854889b74953abd7e40
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This reverts commit 969ed357f823659a6861a2ca38f3ad9d7b58f949
Reason for revert:
According to partner issue b:112448519 comment#80, it impacts
skin temperature specifications.
Change-Id: I7603c3816f34adebc1f67eff6fad214557544022
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
This patch ensures following 2 features
1. Enable IGD controller in devicetree.cb
2. Pass required FSP UPD to perform internal graphics initialization
Change-Id: I607199590d793a70e1e20bb3241fc34467aa829d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This implementation adds below support:
1. Add support to read memory strap.
2. Add support to configure below memory parameters
-> rcomp resistor configuration
-> dqs mapping
-> ect and ca vref config
3. Include SPD configuration
BUG=b:120914069
BRANCH=None
TEST=USE="-intel_mrc -bmplk" emerge-hatch coreboot
Change-Id: I9bda08bd0b9f91ebb96b39291e15473492a6bf19
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30248
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:120914069
BRANCH=None
TEST=USE="-intel_mrc" emerge-hatch coreboot
Change-Id: I91db5745d1db16ab4b2fbb7f8c415bd7c1eb29e9
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/30227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Incorporating some feedback to initial hatch mainboard checking
(CL:30169) that came in after the CL merged.
Updated the chromeos.fmd with the following,
* SI_ALL = 3MB
* SI_BIOS = 16MB
BUG=b:20914069
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/hatch -x -a -v
Change-Id: I4e311c68873f10f71314e44d3a714639a06dbee8
Signed-off-by: Shelley Chen <shchen@google.com>
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30296
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Wipe out all remains of EARLY/LATE_CBMEM_INIT.
Change-Id: Ice75ec0434bef60fa9493037f48833e38044d6e8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/26828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Migration of globals is not needed as there is no real CAR that
gets torn down.
Change-Id: Id24642b49fab811e59291747eda8632cd49d83d0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
This reverts commit a914152fa6072c443ccd18de22412b47a228e754.
Reason for revert:
According to the partner on this project, custom values like this
are no longer necessary.
Change-Id: I393eb4997f58abe0f77161999474994f06741519
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
WWAN chip support 3 interfaces as pci express, USB 2.0 and USB 3.0, the
usgae of Sarien choose to only use USB interface but not over pci
express, so totally disable pci express root port 12.
BUG=b:1246720
TEST=Boot up into OS with WWAN attached, cold boot and warm boot 10
cyles can still device can be listed under lsusb.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ic4da393c0c0d903848111e1c037c2730c86afa7d
Reviewed-on: https://review.coreboot.org/c/30350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Report correct board information for Whiskeylake RVP to OS.
Use short board name like other RVP as it's used
for firmware version check in auto test.
Change-Id: I3f7c95f136e39b978a335cc7855cac819043db7c
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-on: https://review.coreboot.org/c/30318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Boon Tiong Teo <boon.tiong.teo@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Remove duplicate entry of dptf_enable.
BRANCH=None
BUG=None
TEST=None
Change-Id: I3ddd6a702180624d31c5c58c71acdce8f627c925
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30338
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add SPD file for micron_dimm_MT40A512M16TB-062EJ (ram id: 12)
BUG=b:121217853
BRANCH=firmware-nami-10775.B
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: I45e6a7a183556fb085f5442cd6bb429d79ef4235
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add SPD file for sdp micron_dimm_MT40A256M16LY-075F (ram id: 11)
BUG=b:120884302
BRANCH=firmware-nami-10775.B
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: Icf731bfefd550e9b94b6404bc870d4d76451deb1
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
These boards are still using LATE_CBMEM which was agreed upon to
be removed after release 4.7. It is now more than 1 year later
and they still linger around.
The work and review to bring those boards up to date can happen on the 4.9
branch and then squashed and merged back into mainline when done.
Change-Id: Iede79ef50681f769a47ce3d66b335dae92aef56b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add code support to enable H1 TPM interfaced to SOC on GSPI0.
The TPM interrupt is mapped to GPP_C21.
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: Ib63a0b473f632d91745102ebd01993e8d65b9552
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30210
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This implementation cleans up gpio configuration functions
and limit definition to baseboard only for now, until variant
specfic overides are needed.
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: I563f6b97812b32d6e3d99e3df512dc112da78aea
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30291
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 999b916015ea0558e3821bdb51501b43a60b5ed6.
The DMIC doesn't have an ACPI id. The patch which enables ACPI
device with id DMIC may create conflict in the feature. Also the
ACPI id "DMIC" doesn't comply with ACPI naming conventions. The
issue for which the patch was introduced, is already addressed in
kernel DMIC driver and the patches are upstreamed in to the Linux
kernel.
Change-Id: I42cb076700dcb5906599471bebfcd5b265b17644
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/c/30151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
All the kaby lake variants uses HDA verb table except RVP8,
hence unselect SOC_INTEL_COMMON_BLOCK_HDA_VERB for RVP8 and
enable for other variants by default.
BUG=None
TEST= Tested on KBL RVP11 and verified the audio functionality.
Signed-off-by: Praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Change-Id: I64d18ab62cfc08b5560dbcf1b77e975eb68c8d30
Reviewed-on: https://review.coreboot.org/c/30267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Boon Tiong Teo <boon.tiong.teo@intel.com>
|
|
Change-Id: Iab2737940f07afb4f5a29ff50e6cb2a22027c51b
Signed-off-by: Bob Moragues <moragues@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30094
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New emmc DLL values for Yorp.
BUG=b:120561055
BRANCH=octopus
TEST=Boot to OS, chromeos-install, mmc_test
Change-Id: I771c959a15959160224f056c0a16aa65bfbba94e
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30073
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Sometimes the platform boots in an invalid state, that will cause
FSP-M to fail. As a board_reset() doesn't fix it, issue an full_reset()
as soon as the IA32_FEATURE_CONTROL MSR is locked at beging of romstage.
Tested on wedge100s. After full reset the system behaves as normal.
Change-Id: I1a382b8fb650311b0c24b48e0986d22edfa2d261
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Turn on power optimizer of PCH side DMI and SATA controller.
BUG=N/A
TEST=Build and boot up into sarien platoform, able to finish 100 cycles
of s0ix.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I41da2b4106d683945cdc296e2a77311176144f43
Reviewed-on: https://review.coreboot.org/c/30212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Use 2T memory timings on Liara for all board IDs.
BUG=b:116082728
TEST=Build & boot on Liara
Change-Id: I5814e63db35cf7761f4f20792b0f3cf4120a1b60
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/30285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
|
|
Set CONFIG_NO_FADT_8042 to avoid probing for the 8042 controller.
This speeds up boot on nocturne by 1.3 seconds:
Before change:
[2.162266] EXT4-fs (mmcblk0p3): mounting ext2 file system using
the ext4 subsystem
After change:
[0.867735] EXT4-fs (mmcblk0p3): mounting ext2 file system using
the ext4 subsystem
BUG=b:120960844
BRANCH=none
TEST=build, flash, and boot nocturne; check dmesg to verify that
boot is faster and that you don't see the following log in dmesg:
[0.671501] i8042: Probing ports directly.
Change-Id: I62a16e6de5e74fa17970d9967f6d1628497ec1d3
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/30283
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The TXE PCI device serves no function under Linux, and doesn't
work properly under Windows, so disable/hide it from the OS.
Test: Boot Windows 10 on google/squawks, verify TXE not visible
under Device Manager.
Change-Id: Idaa152e15106b826fd5aa787090acd45719f4228
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Commit 73b723d [google/cyan: Switch Touchpad and Touchscreen...]
in additon to changing the touchpad/touchscreen interrupts from
edge to level triggered, also marked them as maskable. This not only
broke the touchpad functionality, but caused issues with the touchpad
as well. Revert the touchpad to being non_maskable for all cyan
variants with a touchscreen.
Test: boot GalliumOS on google/cyan with a range of kernel versions
(4.15.18, 4.16.13, 4.17.x, 4.18.x) and verify touchscreen functional,
touchpad working properly (not jittery)
Change-Id: I0e0357912f9404af7d0f4e7938a1a94c74810b37
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This board doesn't have a UART on the super I/O. Selecting this option
speeds up boot time from ~493 ms to ~416 ms.
Change-Id: I1d84f373831381da79022638e1082adf68f47aad
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
When I debug with HiFive Unleashed, I found that hart 4 could not be
running. Then find the duplicate MAX_CPUS definition. The correct
MAX_CPUS is located in src/soc/sifive/fu540/Kconfig
Change-Id: I583f6ba548daeeb6c7e341dc3fa8817e7dec5697
Signed-off-by: Xiang Wang <wxjstz@126.com>
Reviewed-on: https://review.coreboot.org/c/30179
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ide30a7396b6248e2037041e177dc8514533718a4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The following was tested:
- Using two DDR2 DIMMs
- S3 sleep and resume (on SeaBIOS it needs sercon disabled)
- Ethernet NIC
- Libgfxinit (native res and textmode)
- SATA
- USB
- 800MHz FSB CPU (Pentium(R) E5200 @ 2.50GHz)
- PS2 Keyboard
- Serial output
TODO:
- Add ACPI code for SuperIO devices (done in a follow-up patch)
- Add documentation
TESTED with SeaBIOS (sercon disabled), Linux 4.19
Change-Id: I483e1143e4095b8a58fed142d31ca7f233a854e2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30239
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I85b5aef758a1ed30c46ed0adabec3293edb0f3fd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
Define SATA mode to AHCI mode instead of 0, make devicetree more
readable.
BUG=N/A
Change-Id: I903545d9487c1409f9008407fe5bee6aa4959b98
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
When I added the cmos.layout file, I did not realise that the
southbridge code cleverly emulated the "keep state" option.
Tested on an ASRock H81M-HDS. The `Keep` option works as it should.
Change-Id: I908e59d1e1eedefa6610e7f980afc3c04390a519
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Enable ELAN Touchpad and Disable ALPS Touchpad
BUG=b:119628524
BRANCH=master
TEST=ELAN Touchpad can work normally.
Change-Id: I7839459a70768fa95ba4871b1915d2ea86419bbb
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Change-Id: I4ee3cc42302c44dc80ae1f285579a4d1775aec16
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/30199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The previous settings caused the I2C frequency for the audio bus to be
too high, at 417kHz. The settings in this commit correct the frequency
to 396kHz.
BUG=b:119423345
Change-Id: Ibed886e6e1b0df4df6b87f6291e515364b3bf718
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit ad41f5512306d118047d2f7243678ddb32b4b06b.
Reason for revert: <Issue have seen on EVT platform that vboot always fail to verify keyblock A>
BUG=b:121169122
Change-Id: I2790ef3463a228008b614498009fbdc8b493cfb0
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30286
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When the BMC firmware module is installed on the KGPE-D16, the
RAM SPD multiplexer lines are disconnected by hardware from the
SP5100 GPIOs and attached to BMC GPIO lines instead.
Set the BMC GPIOs to match the state of the SP5100 GPIOs during
RAM setup.
Change-Id: Ia251334ae44668c2260d8d2e816f85f1f62faac5
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/19820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enable Elan touchpad and WACOM touchscreen
BUG=b:119924134, b:120103010
BRANCH=master
TEST=Verify touchpad and touchscreen on arcada work with this change.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I3dcdb4eeeb32766e64553d9e69e6b7e2b5ba85aa
Reviewed-on: https://review.coreboot.org/c/30146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Commit d80884ea5a ("mb/google/kahlee: Disable IOMMU") disabled the IOMMU
in all kahlee variants, but omitted the explaining comment only in
liara's devicetree.cb. Copy this comment to liara.
Change-Id: I564013a16217445003467e2a0579abd50597b205
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Using ${...} in some places is slightly confusing.
Fixes: 395cbb4f97 ("mb/*/*/Kconfig: Use CONFIG_VARIANT_DIR for devicetree")
Change-Id: Id0856a10d92786a41d45ca697945699f6f4c1f4c
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Sync'ing the sku_ids list in the master sku sheet.
BUG=b:112876867
Change-Id: I658e8dc67679b5b528ab267861a1151f50e42414
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update dptf settings for Charger throttling. Also, update Power
Limit1 minimum value setting from 4.5W to 3W.
BUG=b:112448519
BRANCH=octopus
TEST=Built and tested on Fleex system
Change-Id: I8c2a796ff28254ebef28ed5745b344f925d6e649
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Bobba would prefer to use different SAR values per sku-id for regulatory
compliance. This commit uses the newly added interface for custom wifi
SAR CBFS filenames.
CQ-DEPEND=CL:*729429
BUG=b:120958726
BRANCH=octopus
TEST=build
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Change-Id: I354382d651d65d533459f0ca460ca6fd6de547fd
Reviewed-on: https://review.coreboot.org/c/30223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
According to bard/ekko cpu types, PL2 need to set the values
1. KBL_U PL2 is 25w.
2. KBL_R PL2 is 29w.
BUG=b:120874861
TEST=power on and check the DUT can boot up well
Change-Id: I5f9d672c4244c363a7cfb362653663a065259fc0
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enaebl the RTC driver to be used on mc_apl4.
Change-Id: Ib8d2a9f6b8cea47cd10db4dfcc59eec1b21c7993
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/30205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Enable PTN3460 chip initialization to get LVDS attached LCD working on
mc_apl4.
Change-Id: I3ccf5398f16831db321eba846d6b041daadf31dd
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/30204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Add GPIO configuration to match the hardware of mc_apl4.
Change-Id: Ia69603f42c57c1cc682550b8eeeab42fbac27563
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/30128
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
helper function
This patch replaces cpuid(1) references from icelake mainboard
with x86 cpu common code library functions cpu_get_cpuid().
- cpu_get_cpuid() -> to get processor id (from cpuid.eax)
Change-Id: Ia12d95d911dd6ee60a3a35937264fef668ad9e35
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
This patch implements board reset on the Cheza board. The real board
reset used by the operating system uses the PMIC, but unfortunately the
PMIC needs to be configured right for that to work. The PMIC
configuration currently happens in the Qualcomm blob (QcLib) that is run
from romstage, but vboot needs to be able to reboot during verstage
already. Porting all the PMIC initialization code to run in the
bootblock seems excessive (and at odds with the goal of doing as little
as possible before verification), so we'll just do a little hack and ask
the EC to perform a cold reset instead. For vboot purposes, this should
work just as well.
BUG=b:118501305
TEST=Hacked vboot code to call vboot_reboot(), confirmed that board
reset and came back up as expected.
Change-Id: I3858d95f481884a87c243d4fa3d6369c1e8a5a2c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/29849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New emmc DLL values for Bobba.
BUG=b:120561055
TEST=Boot to OS, chromeos-install, mmc_test
Change-Id: I5a0d9587a91b3c71c042cd8ea360c816ea29fb91
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30176
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
file Module Part Number
Correct Ram_ID=0b0000 SPD Module Part Number mismatch last alphabet 'C'
to "H5AN8G6NAFR-UHC".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I4f4b83589ad6b53c0a24f2637f0fe8b92a1168e3
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
file Module Part Number
Correct to add Ram_ID=0b0001 SPD Module Part Number mismatch last alphabet 'C'
to "H5ANAG6NAMR-UHC".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I4d320b2e10c4865456a9a9ccb400db5dd9256b3e
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30177
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Creating skeleton files and directories in mainboard for the new Hatch
board. This is to facilitate development for different parties
involved.
BUG=None
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I5fc60c178f83034abe5d846d0f4169072b66f448
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/30169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
Change-Id: I64e79904c7ad95091ea29d9f80444c4e3b493471
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/29298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Update the TRACKPAD_INT1_1V8_ODL GPIO configuration so that it acts as a
wakeup source
BUG=b:119598593
BRANCH=octopus
TEST=Ensure that the system wakes up on trackpad events. Ensure that the
suspend_stress_test runs successfully for 25 iterations.
Change-Id: I28292682cf9c8037abb87d265e49a60139550db2
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/30171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I15cfbbab15b940641c3952f2cfb4b11c37574816
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/29299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add reset delay in power resource to prevent bind to fail after unbind.
BUG=b:119795901
BRANCH=master
TEST=emerge-octopus coreboot,
verified that WACOM touchscreen can re-bind successfully.
Change-Id: Idcf02b1c931ed64951995403ec9ebe6b8f2db31d
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30099
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable SATA port 0 and port 1 as that's not used as SATA on platform.
BUG=N/A
TEST=Build and boot up fine on google arcada board.
Change-Id: I1b8801f7a0f9b7847b85d7c315fa0a2093b32f70
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
There's no LAN connection on Arcada board, so disable PCH GBE.
BUG=N/A
Change-Id: I07c66df50dbe9fefd95a67b5af9e3f61ce6a18aa
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
There are 2 vendor BIOS's for the Lenovo X200 with the difference being the
settings in the VBT blob to accommodate different backlight frequencies.
Linux however sticks with the setting set by the firmware.
Tested on Lenovo X200 with CCFL backlight.
Change-Id: I4c4a7011ce03cdd511fa2e2160c2f006ba2707ba
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29904
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
correct memory part name
form hynix_dimm_H5ANAG6NCMR-VKC
to hynix_dimm_H5AN4G6NAFR-UHC
BUG=b:113983573
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: I0c33343eb1269919fba324333897805da1d1ff9b
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
This implementation configures below parameters:
1. Enable SaGv, isclk.
2. Set Pcie rootport enable, Clock source usage and clkreq.
3. Configure SATA and LPSS controllers parameters.
4. Enable CNVI controller, configure Wifi end device under PCIE RP1.
5. Add TPM device support under GSPI1.
Change-Id: I585e82799eea0bad19ad2c94d6b4b3024f930ed4
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
PEN_EJECT GPIOs are active high and also require an internal pull-up.
Update the GPIO configuration appropriately.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the stylus
tools open on pen eject. Ensure that the system can enter S0ix and S3
states successfully when the pen is inserted. Ensure that the system
wakes on Pen Eject. Ensure that the system does not enter S0ix and S3
states when the pen is placed in its holder. Ensure that the
suspend_stress_test runs successfully for 25 iterations with the pen
placed in its holder.
Change-Id: Ibf9cb214a8ce7561efbb77a7e99d1e386cf064c3
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30107
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update the GPIOs for the next board build. Mostly minor changes but
the polarity change on GPP_E8/RECOVERY on sarien will result in it
booting to recovery every time unless using new hardware.
For this reason the recovery mode GPIO that is passed to vboot is
commented out for sarien. It is only used for testing and currently
it is useful to have an image that works on both board versions.
Change-Id: I32d84f3010cb4d3968370a03f7e191b1710a50e8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30062
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently CoffeeLake FSP is incorrectly modifying GPIO pad configuration
if specific UPD variables are not set as it expects.
This affects the display-related SOC pads with the following UPD variables:
UINT8 DdiPortBHpd; // GPP_E13
UINT8 DdiPortCHpd; // GPP_E14
UINT8 DdiPortDHpd; // GPP_E15
UINT8 DdiPortFHpd; // GPP_E16
UINT8 DdiPortBDdc; // GPP_E18/GPP_E19
UINT8 DdiPortCDdc; // GPP_E20/GPP_E21
UINT8 DdiPortDDdc; // GPP_E22/GPP_E23
UINT8 DdiPortFDdc; // GPP_H16/GPP_H17
Until FSP is fixed to not touch the pad configuration this workaround
will reprogram the GPIO settings after FSP-S step so they are correct
when the OS attempts to use them.
This was found in CoffeLake FSP Gold release:
https://github.com/IntelFsp/FSP/tree/master/CoffeeLakeFspBinPkg
As well as the current top-of-tree for the FSP sources.
BUG=b:120686247,chromium:913216
TEST=verify correct GPIO configuration for GPP_E group in the kernel
Change-Id: I19550c4347cf65d409de6a8638619270372c4d0a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Synaptics Trackpad wake event is incorrectly routed to GPE0_DW2_02. The
concerned GPIO is not connected and hence wont trigger a wakeup. Fix the
GPE wake configuration for synaptics trackpad.
BUG=b:120666158
BRANCH=octopus
TEST=Ensure that the wake on trackpad works with Synaptics touch pad.
Ensure that the system can enter S0ix successfully(run
suspend_stress_test -c 25).
Change-Id: I87b8c266266280f61700839d428e6f8938b0f72f
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30105
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
FSP defined a special clock source usage 0x70 for PCH LAN device, update
that to google sarien platform.
BUG=b:120003760
TEST=Boot up into OS, ethernet able to be listed in ifconfig.
Change-Id: I9f945be4f0ce15470ab53f44e60143f3fd0fddf8
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Part Number
Correct Ram_ID=0b0011 SPD Module Part Number to "MT40A1G16KNR-075:E" from
"4ATS1G64HZ-2G6E1".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I9d582b3753de9a48865eb6eca7e4fbdb31b799ff
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Number
Correct Ram_ID=0b0000 SPD Module Part Number to "H5AN8G6NAFR-UH" from
"HMA851S6AFR6N-UH".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I1f6e885638589a35334a9a8f905af4877c5d1f91
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Part Number
Correct Ram_ID=0b0010 SPD Module Part Number to "MT40A512M16JY-083E:B"
from "4ATF51264HZ-2G3B2".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I6847a55968260cdbc1588ddeb8d23c515ad87920
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The Intel Sensor Hub was enabled on the wrong variant so this change
moves the enable from sarien to arcada.
Change-Id: If933623f7dbb45c4805fb61430465236eca19ee8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Li1 Feng <li1.feng@intel.com>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
A new liara specific VBIOS updating eDP power sequence is available now,
Change Kconfig to use it if board is google liara.
BUG=b:120534087
TEST=Build liara, booted, tested eDP test compliance.
Change-Id: I444cfa0bd755480e006f11c0d692b25b96129c29
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/30090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The code is based on autoport and that for T430s
Tested:
- CPU i5-3337U
- Slotted DIMM 2GiB
- Soldered RAM 4GiB from samsung (There may be more models here)
- Camera
- pci-e and usb2 on M.2 slot with A key for wlan
- sata and usb2 (no superspeed components) on M.2 slot with B key for wwan
- On board SDHCI connected to pci-e
- USB3 ports
- libgfxinit-based graphic init
- NVRAM options for North and South bridges
- Sound
- Thinkpad EC
- S3
- TPM1 on LPC
- EHCI debug on SSP2 (USB3 port on the left)
- Linux 4.9.110-3 within Debian GNU/Linux stable, loaded from
Linux payload (Heads), Seabios may also work.
Not tested:
- Fingerprint reader on USB2 (not present on mine)
- Keyboard backlight (not present on mine)
- "sticky_fn" flag in nvram
Not implemented yet:
- Fn locking in nvram (may not be identical to "sticky_fn")
- C-based native graphic init (since T431s has eDP instead of LVDS)
- Detecting the model of Soldered RAM at runtime, and loading the
corresponding SPD datum (3 observed) from CBFS (the mechanism may be
similar to that on x1_carbon_gen1 and s230u, but I do not know how
to find gpio ports for that, and SPD data stored in vendor firmware.)
Change-Id: Ic8062cacf5e8232405bb5757e1b1d063541f354a
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Provide rise/fall times as measured on existing boards. This will
need adjusted for new boards but provides a starting point that
makes I2C clocks look reasonable.
Tested by measuring I2C bus speed and rise/fall times with a scope.
Change-Id: Ic18010f5efc41dcee8925d696767ba2c44e3df4b
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
According to issue tracker b:119899090.
https://partnerissuetracker.corp.google.com/issues/119899090
We modify rammus devicetree.cb .i2c[1] configuration to meet ELAN touchpad I2C special timing requirement.
BUG=b:119899090
BRANCH=firmware-rammus-11275.B
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and check touchpad I2C characteristics meet requirement
Signed-off-by: YanRu chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: Ifeb08c2530e6a7674f23f7d48cefa16cfc59cb13
Reviewed-on: https://review.coreboot.org/c/29922
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:119799550
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Change-Id: I926c988c141628ae2d98206f9eb615d06357a366
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Re-write the UAO handling code as it had stopped working (#171)
(the flag was not getting read from the RTC properly in SMM)
Remove the SMM code as it's not needed (but EC flag won't be set
upon entering S3 now)
Set the EC flags on boot the same way other flags are set
Document bitwise operators for clarity
Propagate changes to other Thinkpads
(updated X201 to have 2 bits for the flag as it only had 1)
Per Nicola Corna's previous commits, 0x0d is set for "AC only"
"AC only" does exhibit different behaviour - the USB port is
turned on a few seconds after entering S3, rather than < 1 sec,
regardless of AC status
Tested on X220
Change-Id: If812cd1ef8fb1a24d7fadbe834f574b40cbcd56a
Signed-off-by: Nathaniel Roach <nroach44@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Tested - Lenovo t520 still builds fine with this patch.
Change-Id: I82492c071ca760f0790b992acbdb86021f470cfe
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Turn on the ISH in the device tree.
BUG=b:120295222
Change-Id: I0ba08c245d050aebc6eb06055690c422ab9b51c6
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30034
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=build & run
Change-Id: Ie404faf37617d2ad792310709ca2063f9a372076
Signed-off-by: Mukesh Savaliya <msavaliy@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/25392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Move the backlight initialization from bootblock to romstage
BUG=b:120436919
TEST=Careena backlight is enabled
Change-Id: Ia4993b993d37afaf9e23d6f3316ba91053732f1d
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Platform have a 32MB SPI chip, so we can increase the bios region from
16MB to 28MB.
BUG=b:119267832
TEST=Build and boot fine on sarien platform.
Change-Id: I9bc0fa0f662e5ec64e77f2005dbb2e7edb8b2524
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
AMD traditionally claims the resource at I/O port 61 for the onboard
PC-AT speaker. In later designs, the speaker may be omitted in favor
of routing the SPKR signal to the codec.
Some systems implement neither, and for those it is not correct to
identify the resource as a speaker. Modify the EISAID reported to
the OS depending on the system design. The default is that port 61
is reported as reserved. In order to report a speaker, add #define
in mainboard//dsdt.asl.
TEST=check /proc/ioports and iasl -d for both ways using a Grunt
BUG=b:117818432
Change-Id: I33aafb187f9fea7b38aae43c399292c7521fcfc4
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ifb08c903e19ef4e93bdc9cbc9844cb1888a8d2fa
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Sort mainboard-specific defines in the same order as in all other Lenovo
boards. This is a purely cosmetic change which just makes diff between
boards smaller.
Change-Id: I4e379bb727b356fc6010e93de492f6d73f97a750
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Most Lenovo mainboards define their own specific defines in dsdt.asl.
Let's make it consistent across all Lenovo mainboards.
Tested - builds fine.
Change-Id: I03fbeb09b25e42af2dfbb220c0f726e6abb73673
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
