Age | Commit message (Collapse) | Author |
|
The new edid functions support converting the edid to an lb_framebuffer.
Use them. Also, since panels seem to set bits per color instead of bits
per pixel, just force the right value in the edid struct.
Add helpful comment because people don't always believe we need to set
the pallette.
While we're at it, fix a problem that caused it to not compile.
Change-Id: I645edc4e442d9b96303d9e17f175458dc7ef28b6
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/57619
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/4327
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Don't force dev mode. Allow users to enter / exit dev mode as normal.
Change-Id: I168eb04a8ac102a8c4a1ca8936f78f62b001e0eb
Reviewed-on: https://gerrit.chromium.org/gerrit/59492
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Reviewed-on: http://review.coreboot.org/4321
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On some systems there may be 2GB SKU that is the same as the
4GB SKU but just one channel of memory. In that case we need
to ensure that both copies of the same SPD source end up
populated by ensuring that repeated entries are included by
using $+ instead of $^.
Alternatively we could do the check inside romstage, but it
is already set to behave this way if the SPD gets populated
correctly.
I changed spd_index to 3 in falco romstage to force it to
pretend it was a 2GB config of the same memory, then booted
to ensure it was indeed limited to 2GB.
memcfg channel[0] config (00780008):
ECC inactive
enhanced interleave mode on
rank interleave on
DIMMA 2048 MB width x16 single rank, selected
DIMMB 0 MB width x16 single rank
memcfg channel[1] config (00600000):
ECC inactive
enhanced interleave mode on
rank interleave on
DIMMA 0 MB width x8 single rank, selected
DIMMB 0 MB width x8 single rank
Change-Id: Ibfe5051ccda2fe69e8caff3f3c264116e3411c65
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59483
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Jay Kim <yongjaek@chromium.org>
Reviewed-on: http://review.coreboot.org/4319
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Propagated from
http://review.coreboot.org/3347
http://review.coreboot.org/3374
The cause of this issue is:
USB devices use bit 11(0x0b) of GP0_STS represents S3 wake up event,
but this bit is not clear after wake up. So OS thinks there is a
wake up signal and wake up immediately.
Both amd/olivehill and asrock/imb-a180 have been validated.
Change-Id: I7c26cb07bcd2e62bb792809b67314e5155c6adf6
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/4261
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The AML code of PTS and WAK for southbridge are in
UINT8 AlibSsdtKB[], Proc/GNB/Modules/GnbInitKB/AlibSsdtKB.h.
It was integrated into SSDT even it was called by nobody.
The source ASL was provided by AGESA for reference, but it
has been scrubbed when it was ported to Coreboot.
Without the calls, Olive Hill can not wake up if it boots Windows.
Both amd/olivehill and asrock/imb-a180 have been validated.
Change-Id: Ia7bba29904dbd6f33fdb08bf88bb499005ef561b
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/4260
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Variable use is specific to ChromeOS.
Change-Id: I5b61a038e6b08e3b2408c4d990749d45fdf2148d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4306
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change-Id: I1a59405499deceed7df01a03834be72830e6578f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4291
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Cougar Canyon 2 is a Ivybridge/PantherPoint reference board.
This implementation uses the Intel FSP (Vist the Intel FSP
website for details on FSP architecture and support).
The FSP does not support s3 at this time. S3 may be added
when it is available in the FSP. All other features and IO
ports are functional. Booted on Ubuntu 12.04 and 13.04,
Fedora 18 with SeaBIOS payload. Memtest86, FWTS, and
other tests pass.
Board support page will be updated on acceptance.
Change-Id: I26c0b82d7ac295498376ad4c3517a9d6660d1c01
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4018
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
It's done in bootblock_simple.c just after returning from
the mainboard specific bootblock function.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I96cab5e406132a9f7dc30d48ff99f524773a1a14
Reviewed-on: https://gerrit.chromium.org/gerrit/58473
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Tested-by: Stefan Reinauer <reinauer@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
Reviewed-on: http://review.coreboot.org/4257
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
The OIPG package needs to have >1 member to make the chromeos_acpi
kernel driver do the right automagic sysfs topology creation.
Additionally an "unimplemented" GPIO should be reported as 0xFF
because 0 is a valid GPIO number.
verify crossystem on slippy
$ sudo crossystem | grep -e recoverysw_cur -e wpsw_cur
recoverysw_cur = (error)
wpsw_cur = 1
Change-Id: I06dff09152bde30a3ffe58b1defe9d299155472c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57471
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4221
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This config option was not enabled which was preventing
the user from enabling developer mode from recovery mode.
With this enabled we can disable the "dev mode by default"
behavior and let people enable it by entering recovery mode.
This will make the firmware behave like a typical chromeos
device.
Peppy is left in "default dev mode" until after bringup.
1) boot slippy in normal mode by default
2) enter recovery mode with servo button
3) Ctrl+D on USB keyboard to enter developer mode
4) boot slippy in developer mode
Change-Id: I414c0d10dd0489e3c89798f75a2872a43297c8d8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57350
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4220
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Those building Chromebook firmware from coreboot git might be more
interested in building without ChromeOS extras.
Change-Id: I2f176d059fd45bf4eb02cc0f3f1dcc353095d0ce
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3977
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Instead of depending on exact mobo configure general characteristic whether
dock is configured in romstage or ramstage.
X60 and T60 have superio in dock so it needs to be inited to get serial, so
it should be inited in romstage.
On X201 there is nothing useful that early in boot but it's needed to init more
to get dock working, in particular EC init needs to be done first.
Change-Id: If5072e3dec883a94cd2d5643a92f7f6c3c9feee9
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4294
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Instead define brightness up/down function and gfx device and use
preprocessor magic to glue it together.
Change-Id: I03074ae07b33c1546d229efc3e80606ddbee6300
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4282
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Do not directly check the return value of get_option, but instead compare
the returned value against a CB_CMOS_ error code, or against CB_SUCCESS.
Change-Id: I2fa7761d13ebb5e9b4606076991a43f18ae370ad
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4266
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
- Add a new USB location field
- Add a new "ddr_refresh_2x" field, enabled on Falco only
- Fix copy+paste bug in baskingridge
Checked that tREFI is halved during memory setup in the memory
training log:
tREFImin = 6240 << DEFAULT
C(0).tREFI = 0xc30 << MODIFIED (=3120)
C(0).tREFI = 0xc30 << MODIFIED (=3120)
Also ensure that the SD card is detected properly again.
Change-Id: Ie3a82c08df06ada9af56282b5255caefa56487f2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57349
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4219
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
These are based on the datasheet and I included the timing
values I used from the docs.
Change-Id: Ib75b2c5e50ac09d1e4cf9dd22229bb0f0a8965a4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58540
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4234
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
- Add HDA verb table
- Add on-board device table
- Add panel power sequencing values
Change-Id: I1b3450c2740ec1d930f157a9b23550e1efc8668f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58197
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4233
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The Linux thinkpad_acpi.c driver looks for this string while
reading information about the system it is running on.
This commit does not make the module load but it is one of
several things that the module looks for on a ThinkPad.
Change-Id: Ia48bbd85ba4d528063695345b0f968d264573341
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/3779
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Currently, all Peppy boards w/ '000' SPD GPIOs have 2GB DRAM. Disable
the second DRAM channel based upon the GPIOs.
Need to change / confirm this for upcoming builds.
Change-Id: I7085ddecb80626cc0bed99ba7b174c6b80350696
Reviewed-on: https://gerrit.chromium.org/gerrit/58620
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4238
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The EC was disabling flash commands and sysjump was not working
properly. With those two fixed software sync works properly.
(Taken from I63ca00d6c94854f2b395eb736ce20792da5f8de2).
Change-Id: I9c7d1d1f1aaf7de33d0cec5f6daf648576ba8900
Reviewed-on: https://gerrit.chromium.org/gerrit/57289
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4212
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Update GPIO table to match board.
- Update USB port map.
- Remove iSSD power sequencing code.
Change-Id: Iaa8e5921ed9db6bcfd18b5a888c7f80b2c93a710
Reviewed-on: https://gerrit.chromium.org/gerrit/56869
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4211
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
A quirk of the Kconfig used in coreboot is that config options
cannot be overriden by local config changes unless they have
a description string.
1) Add CONFIG_MAINBOARD_VENDOR="Custom" to local config
2) Build and flash coreboot
3) cat /sys/class/dmi/id/sys_vendor and look for "Custom"
Change-Id: I1b5f2124cd4a22c056c025143ae5bcaafa6b03f0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59088
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4248
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The wake device input pins are active low and the
GPIOs need to be set as inverted when they are marked
as an input so they are not spuriously logged.
Also sync pin states from Falco initial commit.
Reference change: I15d38dcc9b2fb4b2b0eb27da358fa3c343e22323
Change-Id: I66e136d389d53a367436d816fa84dacdc8e86bad
Reviewed-on: https://gerrit.chromium.org/gerrit/58334
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@google.com>
Reviewed-on: http://review.coreboot.org/4247
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Set nid 0x12 instead of nid 0x05. The DMIC is on NIC 0x12.
Change-Id: Ifc883b65a50aeec6a6d3ad02fe8418f124e6241d
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58711
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Jay Kim <yongjaek@chromium.org>
Tested-by: Jay Kim <yongjaek@chromium.org>
Reviewed-on: http://review.coreboot.org/4246
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
SPD GPIOs were being read prior to initialization in romstage_common. To
fix, pass the copy_spd function to romstage_common, to be called at the
appropriate time (after PCH init, before DRAM init).
Change-Id: I2554813e56a58c8c81456f1a53cc8ce9c2030a73
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58608
Reviewed-on: http://review.coreboot.org/4237
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Due to OEM request, always set DDR refresh rate at 2x.
Change-Id: I81a4f57aca6388551dca6effbd9a4ac1a97e4f5a
Reviewed-on: https://gerrit.chromium.org/gerrit/50477
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4214
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Iefc481f09268dd15bbc3cbfa8bdd110d44383f6a
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4281
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The wake device input pins are active low and the
GPIOs need to be set as inverted when they are marked
as an input so they are not spuriously logged.
suspend/resume on slippy with trackpad wake:
8 | 2013-05-29 07:43:14 | ACPI Enter | S3
9 | 2013-05-29 07:43:18 | ACPI Wake | S3
10 | 2013-05-29 07:43:18 | Wake Source | GPIO | 12
and with power button wake:
11 | 2013-05-29 07:43:35 | ACPI Enter | S3
12 | 2013-05-29 07:43:40 | EC Event | Power Button
13 | 2013-05-29 07:43:40 | ACPI Wake | S3
14 | 2013-05-29 07:43:40 | Wake Source | Power Button | 0
Change-Id: I15d38dcc9b2fb4b2b0eb27da358fa3c343e22323
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56940
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4209
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Make the declaration and use of it conditional on the ELOG_GSMI Kconfig variable.
Change-Id: I2ef291d2f3e7d35545014e03ba8e0045da6050e5
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3987
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The EC was disabling flash commands and sysjump was not working
properly. With those two fixed software sync works properly.
Google Chrome EC MKBP driver ready, id 'slippy_no_version'
Clearing the recovery request.
EC hash:7fea29992ef72e3e64d8ffe522aa1dfa68dcb44a2da96a4c19530ea1a0bd22c4
EC-RW hash address, size are 0xffa1cfe8, 32.
Hash = 727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
Expected hash:727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
EC-RW firmware address, size are 0xffad000c, 57180.
VbEcSoftwareSync() - expected len = 57180
Computed hash of expected image:727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
VbEcSoftwareSync() updating EC-RW...
VbEcSoftwareSync() jumping to EC-RW
VbEcSoftwareSync() in RW; done
Change-Id: I63ca00d6c94854f2b395eb736ce20792da5f8de2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56821
Reviewed-on: http://review.coreboot.org/4208
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Set verbs to reflect the layout used for ALC283 in Falco,
which ends up being the same as Slippy.
Change-Id: I3dce4effefaa91ee5bdcbe2a8a3750ebc41376ad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58196
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4232
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Set verbs to reflect the layout used for the ALC283 in slippy.
install on slippy and check that headphone switch works
as does external mic.
Change-Id: I2d6bcda9cf8bbf49cbb6d2dbbe7f1a5adf315d8a
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57560
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4224
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Peppy RAM ID table is as follows:
000 41K256M16HA
001 H5TC4G63AFR
010 EDJ4216EFBG
Elpida SPD taken from Ib1e430cd390b4dbc013fc0802f1a59c1a0412577 by
dlaurie.
Change-Id: Iac156a2d25435514f28e2e73bef617d0fe2d90a1
Reviewed-on: https://gerrit.chromium.org/gerrit/56687
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4201
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Taken directly from slippy with only constant + string changes.
(Peppy port of I4172460d3b075bfd5bb22013a6225cf0e8f95b9c by dlaurie)
The following changes are required in a subsequent commit:
- Add Elpida SPD data.
- Update GPIO map.
- Remove iSSD power sequencing.
- Update USB port map.
Change-Id: I01dfb841f0e9186cf8a0a23f72e7be986a83be42
Reviewed-on: https://gerrit.chromium.org/gerrit/56513
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4200
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
RAM_ID indices have been changed and settled on a 2GB config
that will be the same DRAM chips but only used in one channel.
Change-Id: I444e655883ae045622ab3dfb964da4d7f86e1c0d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56810
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4198
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
These are placeholder values until we can configure for
the exact panel.
Change-Id: If40367c0e5f80d46d085c89b0edae60f1ccacdaf
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56808
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4197
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add the onboard I2C devices for Falco trackpad/lightsensor
and generate SMBIOS Type41 tables for them.
Add ACPI device for the trackpad to expose the interrupt map
to the OS so it can be used.
Configure interrupt GPIOs as PIRQ type and wake GPIOs as
just standard input type. The wake GPIO is reconfigured as
ACPI SCI in the specific device _DSW method. This prevents
the wake GPIO from generating a flood of SCI at runtime.
LTE_WAKE_L_Q and WLAN_WAKE_L_Q are left as ACPI SCI as these
are not repurposed interrupt pins so they are not generated
at runtime.
SIM_DET and ALS_INT_L are set as input since we don't have an
interrupt handler for them.
Change-Id: Ibe9687b2f7f41ead18353c3f650219fe6e94ae2f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56632
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4191
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add the onboard I2C devices for Slippy trackpad/lightsensor
and generate SMBIOS Type41 tables for them.
Add ACPI device for the trackpad to expose the interrupt map
to the OS so it can be used.
Configure interrupt GPIOs as PIRQ type and wake GPIOs as
just standard input type. The wake GPIO is reconfigured as
ACPI SCI in the specific device _DSW method. This prevents
the wake GPIO from generating a flood of SCI at runtime.
LTE_WAKE_L_Q and WLAN_WAKE_L_Q are left as ACPI SCI as these
are not repurposed interrupt pins so they are not generated
at runtime.
SIM_DET and ALS_INT_L are set as input since we don't have an
interrupt handler for them.
tested on slippy with trackpad with additional
kernel changes to chromeos_laptop.c to initialize devices.
1) Ensure trackpad interrupt is functional and that there
is not a flood of ACPI SCI when trackpad does interrupt:
9: 1 0 0 0 IO-APIC-fasteoi acpi
37: 421 0 0 0 IO-APIC-fasteoi cyapa
2) Ensure that devices are exposed as wake capable:
Device S-state Status Sysfs node
TPAD S3 *enabled pnp:00:00
TSCR S3 *disabled pnp:00:01
3) Ensure that trackpad can wake from S3 by default, but
that it does not cause an immediate wake when entering suspend.
4) Ensure that trackpad can be disabled as a wake source with
echo TPAD > /proc/acpi/wakeup
Change-Id: Id562d20b54eeefec56040b8f70ef238911312628
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56622
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4190
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This was provided by the vendor but I added the part number at
byte 128-143 so it can be identified when extracted by mosys.
Change-Id: Ib1e430cd390b4dbc013fc0802f1a59c1a0412577
Reviewed-on: https://gerrit.chromium.org/gerrit/56634
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4192
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
These GPIO accesses were copied by accident and don't
make sense for the baskingridge board.
Change-Id: I03bfc2cf97b6056a746a6c1a27308823ecaa9637
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4204
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The LynxPoint southbridge ACPI code needs the SSDT2 table to function
properly. Otherwise the ACPI evaluator in the kernel spews errors.
Change-Id: I73918545a07e43f4a281ff34d8537340d601b102
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56601
Reviewed-on: http://review.coreboot.org/4188
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Mainboards were defining their own SMBIOS type41
write function. Instead pull this into the generic
SMBIOS code and change the existing mainboards to
make use of it.
Change-Id: I3c8a95ca51fe2a3118dc8d1154011ccfed5fbcbc
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56619
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4187
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Update and use the new pei_data data structure. Now that the
reference code is fixed it's possible to properly disable/enable
the USB2 and USB3 ports correctly.
Change-Id: I075c646e7574be354420b6e59507e8917a97d0f0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56594
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4185
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Only the first two DIMM SPDs are specified so far
- GPIO map is updated
- iSSD power sequencing removed
- USB port map updated
Change-Id: I4172460d3b075bfd5bb22013a6225cf0e8f95b9c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56329
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4184
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Enable GPIO SMI for GPIO34 and set it as inverted so it
is only generated when it is raised by the EC.
1) ec console command: lidopen
2) wait until booted to developer screen
3) ec console command: lidclose
4) ensure system turns off
Change-Id: I7d50f171f3f4539c7c264103d1ffc7c5d0f1c7ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56052
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4177
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
In order to report whether coreboot enabled a SerialIO device
in ACPI mode we had been relying on reading NVS in the _STA
method for the SerialIO device.
The ACPI _STA method has restrictions on what it can access
and is unable to access OperationRegions outside its scope
which means it should not be trying to read NVS.
This change adds a new SSDT to the ACPI tables and fills it
with constants that indicate whether or not a device is enabled
in ACPI mode.
The ACPI code is changed to read these variables from the
SSDT and use that instead of trying to query a variable in NVS.
Attempt to use lpt-clk driver to probe the
device clocks for SerialIO devices and see that the kernel
does not complain about accessing the GNVS region.
Change-Id: I8538bee4390daed4ecca679496ab0cb313f174ce
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51369
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4170
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Disable EC software sync for now
- Report correct EC active firmware mode
- Force enable developer mode by default
- Set up PCH generic decode regions in romstage
- Pass the oprom_is_loaded flag into vboot handoff data
Change-Id: Ib7ab35e6897c19455cbeecba88160ae830ea7984
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51155
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4169
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
These boards were returning 0 to indicate success when
the realmode handler expects it to return 1 to indicate
that it handled the interrupt.
Change-Id: I2baeaf8c2774fa7668a8b2f2d9ad698302eefb21
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50881
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4168
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
These are both pulled up to 3.3V in the schematic.
Change-Id: I12e055a39ff6100300c3d285899b8d6239e3773d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50356
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4164
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Now that we have RW ramstage we don't need to have the
management engine lock down step done in a final SMM.
ME: mkhi_end_of_post
ME: END OF POST message successful (0)
PCI: 00:16.0: Disabling device
Change-Id: I9db4e72e38be58cc875c1622a966d8fcacc83280
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49757
Reviewed-on: http://review.coreboot.org/4153
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Instead of having an OS re-parse cbmem book-keeping records
for the cbmem allocator just to get the console buffer export
the pointer to the memory console directly in a field named 'CBMC'.
This field lives in the GNVS table.
Change-Id: Ief0c4da7b18df66feb9c816c9f4abdf5a72bd3a4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49764
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4149
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Some handlers still had 2 variants, others were
incorrectly guarded by CONFIG_ variables. This
patch straightens them out.
This does not touch the siemens/sitemp_g1p1 which
provides an interestingly complex solution for the
int15 handler.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I5d74fdf7c2ab1faa96ebc2b5ca5c69398449b069
Reviewed-on: https://gerrit.chromium.org/gerrit/48979
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4140
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The format of this function changed but was not updated in
all mainboards. This fixes all Sandybridge/Ivybridge boards.
The int15 handler no longer takes a regs structure as an
argument and instead uses global variables. The yabel interface
is now similar enough that we can drop the duplicate handler.
Change-Id: Icdaae4d6d50884f6d7bce7a167d48cb1d4807010
Reviewed-on: https://gerrit.chromium.org/gerrit/48969
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4135
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Per our discussions with Gerd, qemu will now always do native graphics
on coreboot. The VGA BIOS capability is not needed and will no longer
be supported. Attempts to build without native graphics will result in
an error.
This code builds for both x86 emulation targets. I'm hitting an issue
testing that is unrelated to coreboot; if someone can test, that
would be helpful. Be sure to start qemu with -vga std.
We also add a test for the PCI BAR being zero and return silently if it
is.
Change-Id: I66188f61e1bac7ad93c989cc10f3e0b55140e148
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/4258
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
SandyBridge raminit uses this CMOS option. If it is not declared, the build
fails when USE_OPTION_TABLE is selected.
Change-Id: I1ba1f994d4ea3824dc66e8f35d0b5b24b88d4dd6
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4269
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The chromeos_acpi driver sysfs naming is not what
crossystem expects if there is just one entry in the package
because it does not add a ".#" suffix in that case.
Specify all the expected GPIOs on wtm2 as undefined, which
should be 0xFF and not 0x00 becuase 0 is a valid GPIO.
Change-Id: I9b17e9bab94219695e65b17914c84acf02a0983b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50337
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4162
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
For all the current haswell boards enable the monotonic timer.
The ULT boards use the 24MHz MSR while the non-ULT boards use the
local apic.
Change-Id: I8b19f526a5a49e8467f296c566a2c4263bc5a863
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49763
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4148
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The c-states are configured according to the BWG, however the
package c-states are disabled as they currently cause platform
instability. The exposed ACPI c-state to processor c-state mapping
are as follows for ULT boards:
ACPI(C1) = MWAIT(C1E)
ACPI(C2) = MWAIT(C7S long latency)
ACPI(C3) = MWAIT(C10)
The non-ULT boards have an expoed c-state mapping:
ACPI(C1) = MWAIT(C1E)
ACPI(C2) = MWAIT(C3)
ACPI(C3) = MWAIT(C7S)
Included in this patch is removing the updating of current limit
registers as some of the MSRs are different and the proper values
are currently unknown. Lastly, some of the MSRs were renamed to
match the BWG.
Booted 3.8 kernel and used powertop to note package, core, and acpi
c-state residency.
Change-Id: Ia428d4a4979ba3cba44eb9faa96f74b7d3f22dfe
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48291
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4133
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This adds some macros for the common GPIO defines and drops
the gpio number definition from each entry. The end result
is much easier to read. The wtm2 mainboard gpio list is modified
to use this.
Also fix a bug in the LP version of get_gpio() that was always
returning zero due to a miscompare.
Change-Id: I143e5aee412af1eda84e35f8026f31cf13df508e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48946
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4138
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
With the LynxPoint chipset there are more than 16
possible GPIOs that can trigger an SMI so we need
a mainboard handler that can support this.
There are only a handful of users of this function
so just change them all to use the new prototype.
Change-Id: I3d96da0397d6584f713fcf6003054b25c1c92939
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49530
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4145
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
These are placeholder values until we can configure for
the exact panel.
Change-Id: Ibe88cc3588947366eb1728e5b3e1ab8c8be6dfe8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56807
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4196
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Minor tweaks to variable names in the slippy mainboard
that make it easier to base a new board from without
as much renaming.
Also properly set up the thermal variables for the
thermal zone that is defined in ACPI instead of using
the generic setup from WTM2.
Change-Id: I752c1a50bfdc06b6ddad95bd1331c6870b9f9df2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56328
Reviewed-on: http://review.coreboot.org/4183
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This will log and clear EC events so they do not take effect
when the SMI handler is enabled.
Change-Id: I5ef563f7cedc8977410cc3f69e2655fc4e14c9eb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56055
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4178
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The SerialIO devices have specific requirements for PCI
interrupt mode to use PIRQ{E,F,G,H} that are not being met.
D21:F0 uses PIRQE, which must not be shared with other PCH
D21:F1-F6 share PIRQF, which must not be shared with other PCH
D23:F0 uses PIRQH, which must not be shared with other PCH
- Fix D20IR -> D20IP typo
- Remove D25/EHCI2 as it does not exist
- Reorder other interrupts to clear PIRQE/PIRQF/PIRQH
Check device interrupts in the kernel
0: IO-APIC-edge timer
1: IO-APIC-edge i8042
8: IO-APIC-edge rtc0
9: IO-APIC-fasteoi acpi
16: IO-APIC-fasteoi ath9k
18: IO-APIC-fasteoi i801_smbus
19: IO-APIC-fasteoi ehci_hcd:usb1
21: IO-APIC-fasteoi i2c-designware-pci--1, i2c-designware-pci--1
40: PCI-MSI-edge PCIe PME
41: PCI-MSI-edge i915
42: PCI-MSI-edge ahci
43: PCI-MSI-edge xhci_hcd
44: PCI-MSI-edge snd_hda_intel
Change-Id: Id4c08d11d2860f270c6387138acdc7d3d83a85b5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56028
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4176
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The dev screen was not displaying properly. With the
PWM values programmed the screen displays correctly.
Change-Id: I82b56a92e4168022082a2e519026977ee2ae0c9e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51472
Reviewed-on: http://review.coreboot.org/4172
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The device at function 0 also needs to be enabled
or the kernel will ignore all other functions.
00:15.0 DMA controller: Intel Corporation Lynx Point-LP Low Power Sub-System DMA (rev 03)
00:15.1 Serial bus controller [0c80]: Intel Corporation Lynx Point-LP I2C Controller #0 (rev 03)
00:15.2 Serial bus controller [0c80]: Intel Corporation Lynx Point-LP I2C Controller #1 (rev 03)
Change-Id: I0e1bc7bb719756496c46664d66dc1b1cf2f4d1ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51370
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4171
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This lets the keyboard init get called properly.
Change-Id: I11ffb459907188a58149d28a6ade0b7de7d15d08
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50853
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4167
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: Iae0258ceb0424df0937d2cec7dd885060f5b4e48
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50082
Reviewed-on: http://review.coreboot.org/4157
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: I7a617fe06d23b906f718ed30f1378f7d220b2799
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49911
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4154
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
- 0x200-0x208 for host command window
- 0x800-0x8ff for host command arguments and parameters
- 0x900-0x9ff for exported EC memory map
Change-Id: I064b969843ef0d3c602793d1cb3d82715775c05e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49755
Reviewed-on: http://review.coreboot.org/4151
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Without an LM10506-A the power sequencing for this
part needs to be done manually using GPIOs.
Change-Id: I842152e5f7c30c8dbe37df0c344935a659eb2887
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49648
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4150
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I33876b90902d4a08d760eb482b08ba41be6e3695
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49531
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4147
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: I1bdc52efc827c331c53b97d2b96edafc518d05bf
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/4259
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Without that fix the GTT points at 0x00000000.
The patch was made by Peter Stuge, I just split it
and added a commit message.
Change-Id: Ia378b600ba2faf00d42635c6503b94ff0cb1bc8c
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/4002
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I054edffbb38b13559da10180fc2c6cd9929ba162
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3999
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Move into src/cpu/dmp/dmp_post_code.h
Change-Id: If9f4d842f352eb41618e71f49a226d3cc4ad0b46
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3989
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This permits any software running after the ramstage to tell coreboot that the
boot was successfull.
Change-Id: I6b19160dcf1ea1948360db71d02e344a3bcb44ef
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3992
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On AMD Trinity and Kabini boards errors similar to the following are
shown.
ASSERTION FAILED: file 'src/mainboard/asrock/imb-a180/agesawrapper.c',line 431
DmiTable:100123f7, AcpiPstatein: 10010129,AcpiSrat:0,AcpiSlit:0, Mce:10010de9,Cmc:10010eab,Alib:1002111c, AcpiIvrs:0 in
agesawrapper_amdinitlate agesawrapper_amdinitlate failed: 5
The reason is that on f16kb boards, the CDIT and DMI table are not
created. On f15tn boards, only the DMI table is not created.
Until the root cause is found, disable the table generation to remove
the errors.
Thanks to Wei Hu for debugging and reporting this issue on the list [1].
[1] http://www.coreboot.org/pipermail/coreboot/2013-November/076607.html
CDIT table is not created
Change-Id: I837e3c322bb5331a9b950a72397796a60642c3f3
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/4092
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
|
|
The power to memory is lost during the the suspend, activate
the 3VSBSW# which switches the power during S3 suspend sequence.
As a result resuming from suspend to RAM works now, but now the
GPP ports of the Hudson southbridge are gone after resume from S3.
The devices 15.0 and 15.1 are disabled (decode as ffff) and
therefore anything behind them too [1].
[1] http://www.coreboot.org/pipermail/coreboot/2013-November/076620.html
fam15tn hudson PCIe GPP ports off after resume
Change-Id: Id953313ee4400a03a2ad8ca09e39a5e0d5f92524
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/4041
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Qemu makes the guest uuid (qemu -uuid $uuid) available
to the guest via fw_cfg. Other smbios fields can be
configured in qemu using the -smbios command line
switch (check the qemu manpage for details).
This patch adds coreboot support for this, so the
values provided by qemu will actually show up in the
smbios table.
Change-Id: Ifd9ae0d02749af4e7070a65eadbd1a9585a8a8e6
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/4086
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Starting with release 1.7 qemu provides acpi tables via fw_cfg. Main
advantage is that new (virtual) hardware which needs acpi support
JustWorks[tm] without having to patch & update the firmware (seabios,
coreboot, ...) accordingly.
So if we find acpi tables in fw_cfg try loading them, otherwise fallback
to the builtin acpi tables.
Change-Id: I792232829b870ff6ed8414a3007e0af17f6c4223
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/4040
Tested-by: build bot (Jenkins)
|
|
Change-Id: Iec0abae8a4b18ac737e9ebb3eac219182729be0f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/4057
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Besides the AGESA static settings, the settings in mainboard/buildOpt.c also
change the final configuration. We need to make sure the settings in FchParam
in resume stage are the same as they were in cold boot stage, otherwise the
board can not wake up more than once.
Tested on AMD/Olive Hill, AMD/Parmer and ASRock/imb-a180.
(USB keyboard doesn't work when board wakes up. It is not introduced by this
patch. It needs more debugging.)
Change-Id: I5a5e5502080e358ffc3577dc6a40bb762844d998
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/3932
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
qemu 1.7+ provides a fw_cfg file named "etc/e820" with e820-like entries
for reservations and ram regions. Use it for ram detection if present,
otherwise fallback to the traditional cmos method.
Change-Id: Icac6c99d2a053e59dfdd28e48d1ceb3d56a61bdc
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/4030
Tested-by: build bot (Jenkins)
|
|
Qemu can provide files using the firmware config interface.
This is used to pass config options, virtual machine config
info and option roms into the guest.
This patch adds support for reading the file index and loading
files from qemu.
Change-Id: I57d4a734527c4117239f355121cf1fb8a390ab0d
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/4029
Tested-by: build bot (Jenkins)
|
|
Properly build the super i/o .c files. This prevents including
the .c file directly in romstage, which is generally bad practice.
Adding a Makefile and a .h file to include.
Change-Id: I0be66e94d3062a2c4a445cee2f12ec249598dc8b
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4014
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Remove the COM port enable loop. There is no need to
search for the port when it is needed and known by the
GPIO function.
Change-Id: Ie4e533fd9e49ed9ae62b209317b4b9853ff9926a
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4027
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
What works:
- ACPI interrupt routing for onboard devices
- onboard devices including USBs, ATAs, NICs, COM1
What almost works:
- SMI720 VGA BIOS needs forthcoming VGA BIOS hooks in SeaBIOS to work
Untested:
- Interrupt Line Register interrupt routing
- PIRQ interrupt routing
- MPBIOS/MPTABLE interrupt routing
- unpopulated on board revision 1A AC97 audio
- unpopulated PCI-E x16 slot
- unpopulated ExpressCard slot
- HT expansion board
Thanks to WIN Enterprises for providing boards.
Change-Id: I7787f89b3ab454b668c3b75d0d1cde55b8d53c48
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/3975
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I382e30c92a4c428ec53dd959a5fda4927797fb9b
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/3974
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Ia0c37339aa69b92a1b518fa5e49adc4a7628ae5d
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3979
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
It is expected this will always be a casted get_top_of_ram() call
on x86, no reason to do that under chipset.
Change-Id: I3a49abe13ca44bf4ca1e26d1b3baf954bc5a29b7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3972
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Ubuntu's HDMI audio has noise and echo. Disable NoSnoopEnable can
resolve this issue.
I have tested on Ubuntu 13.04 with AMD Catalyst 13.4 Proprietary
Linux Display Driver[1].
[1]. http://support.amd.com/us/gpudownload/linux/Pages/radeon_linux.aspx
Change-Id: I5d2dddb1b7469d56cd64e3c1e0f4c6c6f095b4ab
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3934
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
|
|
Ubuntu's HDMI audio has noise and echo. Disable NoSnoopEnable can
resolve this issue.
I have tested on Ubuntu 13.04 with latest graphic driver.
Change-Id: I09c19b8925eedee03cfb1d8c0831a84e8aeeba4f
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3937
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
|
|
Windows 7 cannot find HDMI audio device because of acpi setting.
I have tested on Windows 7. I can play music.
Change-Id: I90ade7e7be79f65783922333c2cbb2d3cc6557ea
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3933
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This reverts commit de1fe7f655c549e8dce5b34218221890fa5ccc34.
While things appeared to work, there were actually invalid references
to CAR storage after CAR was torn down on boards without
EARLY_CBMEM_INIT. It was discussed use of CAR_GLOBAL should be
restricted to boards that handle CAR migration properly.
Change-Id: I9969d2ea79c334a7f95a0dbb7c78065720e6ccae
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3968
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change-Id: I67192c8ae99e396ea4b17e03c658f31dbb5c1800
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/3960
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
routing initialization
Change-Id: I6cb4ad5ea5ad40284f8e88ff440f2605d3b83359
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/3959
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
A late for loop may reference over the current array allocation
and corrupt an unrelated global variable. As a quick fix bumb the
size of the array allocation uniformly to 6.
We missed these boards for commit 9c7d73ca because the arrays
had been renamed.
Change-Id: Iff2f2a0090d9302576bc72195d2a3f6fa37ce29a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3954
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
|
|
Windows 7 cannot find HDMI audio device because of acpi setting.
I have tested on Windows 7. I can play music.
Change-Id: I53177ce00b676824a903a3397d69338e8c1a38af
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3936
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|