| Age | Commit message (Collapse) | Author |
|---|
|
List of changes:
1. Drop `HeciEnabled` from dt and dt chip configuration.
2. Replace all logic that disables HECI1 based on the `HeciEnabled`
chip config with `DISABLE_HECI1_AT_PRE_BOOT` config.
3. Make dt CSE PCI device `on` by default.
4. Mainboards set DISABLE_HECI1_AT_PRE_BOOT=y to make Heci1
function disable at pre-boot instead of the dt policy that uses
`HeciEnabled = 0`.
Mainboards that choose to make HECI1 enable during boot don't override
`heci1 disable` config.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I5c13fe4a78be44403a81c28b1676aecc26c58607
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Retype the `pcie_port_coalesce` devicetree options and related variables
to better reflect their bivalue (boolean) nature.
Change-Id: I6a4dfe277a8f83a9eb58515fc4eaa2fee0747ddb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60416
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I1df255d55b8f43a711d836c2565c367bd988098a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Use the common ACPI code to reduce code duplication.
After this change, `PSS_MAX_ENTRIES` is honored correctly in P-state
table generation (as of commit c2540a9) and the number reduces from 10
to 7 entries.
Also, remnants of P_BLK support missed in CB:58096 will vanish.
Tested on google/fizz: no errors in dmesg, ACPI tables remain the same
(except PSS, as mentioned above).
Change-Id: I1ec804ae4006a2d9b69c0d93a658eb3b84d60b40
Tested-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44138
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Switch to common GNVS. No additional fields to those being present in
common GNVS are used by any SKL/KBL device. Thus, they're dropped
completely.
Change-Id: I87ab4ab05f6c081697801276a744d49e9e1908e0
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
The `IRQ_SLOT_COUNT` value is only meaningful when generating a PIRQ
table. None of these boards do it, so specifying this value achieves
absolutely nothing. Drop it to prevent further useless copy-pasting.
Change-Id: I2d63b850c03fc1471c0eef180e8b621311b2c336
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
If the VGA BIOS file path for `VGA_BIOS_FILE` in a mainboard's Kconfig
does not exist in the coreboot tree (including submodules), drop it.
These files should be stored in the `site-local` subdirectory and the
paths specified for each board in `site-local/Kconfig`. For example:
config VGA_BIOS_FILE
default "site-local/x200_vbios.bin" if BOARD_LENOVO_X200
Note that this is just an example. There are better ways to structure
one's `site-local` subfolder. Using the `CONFIG_MAINBOARD_DIR` option
would be one of them, though variants may still need special handling.
Also, update autoport to not generate `VGA_BIOS_FILE` defaults.
Change-Id: I1b5dfba035a42d7943f270f95fb7d32b285584d2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
The `CaVrefConfig` FSP-M UPD describes how the on-die Vref generators
are connected to the DRAM. With the exception of an early Skylake RVP
board (which doesn't have coreboot support), mainboards using DDR3 or
LPDDR3 memory should set `CaVrefConfig` to 0, whereas mainboards with
DDR4 should set `CaVrefConfig` to 2. MRC uses this information during
memory training, so it is important to use the correct value to avoid
any issues, such as increased power usage, system instability or even
boot failures.
However, several Skylake DDR4 mainboards don't set `CaVrefConfig` to 2.
Although they can boot successfully, it's not optimal. For boards that
set `DIMM_SPD_SIZE` to 512 (DDR4 SPD size), set `CaVrefConfig` to 2.
Change-Id: Idab77daff311584b3e3061e9bf107c2fc1b7bdf1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Mainboard information can be found in the included documentation.
Change-Id: I9dfc58bb99e14cd9dac2ac53afc0ea11d2252aa9
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Specify the type of the `DIMM_SPD_SIZE` Kconfig symbol once.
Change-Id: I619833dbce6d2dbe414ed9b37f43196b4b52730e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Since all mainboards use `CHIPSET_LOCKDOWN_COREBOOT`, make it the
default by changing its enum value to 0 and remove its configuration
from all related devicetrees.
If `common_soc_config.chipset_lockdown` is not configured with
something else in the devicetree, then `CHIPSET_LOCKDOWN_COREBOOT`
is used.
Also, add a release note for the upcoming 4.15 release.
Change-Id: I369f01d3da2e901e2fb57f2c83bd07380f3946a6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Specify the type of the `VARIANT_DIR` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: Iea2f992a59e41e00fec3cdc9d6a13b5f3ab0a437
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56558
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `FMDFILE` Kconfig symbol once instead of doing
so on each and every mainboard.
Change-Id: I810bd3fe8d42102586db6c2c58b7037a60189257
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56557
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `OVERRIDE_DEVICETREE` Kconfig symbol once
instead of doing so on each and every mainboard.
Change-Id: I4cbf4e318a30f0cf75aa8690e7454b9caa115c9d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56556
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `MAINBOARD_PART_NUMBER` Kconfig symbol once
instead of doing so on each and every mainboard.
Change-Id: I3692f9e82fe90af4d0da1d037018a20aa1b45793
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56554
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `MAINBOARD_DIR` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: If1cc538b0c4938dac193699897b690e402b3c1e8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56553
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's no need to specify the type of the `CBFS_SIZE` Kconfig symbol
more than once. This is done in `src/Kconfig`, along with its prompt.
Change-Id: I9e08e23e24e372e60c32ae8cd7387ddd4b618ddc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56552
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allow to use the 2nd COM port of the AST2400 which can be also used via
IPMI/serial-over-lan.
Change-Id: I6f9c85b1f5428d3c3acf7a2f20296134c4611b1e
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
If unspecified, chipset code already uses 101, and 0x65 == 101.
Change-Id: I524ca492fa577003df23017756f74a455582132f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Most boards use `device lapic 0 on` with zero written in decimal.
For the sake of consistency, update the remaining boards to follow suit.
Change-Id: I1d3b1ac107e33aae11189cdd5e719b8e48b10f08
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The `tcrt` and `tpsv` values in GNVS can be used to implement thermal
management in ACPI. However, not all mainboards use these values.
On mainboards where `tcrt` and `tpsv` are not used in ACPI tables and
are the only values set in the `mainboard_fill_gnvs` function, remove
them as well as the entire `acpi_tables.c` file. Most files come from
autoport, which unconditionally generates this file.
Change-Id: If2315ddd9700e2da0a24ffecc20acb5c1a1d688e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
SaGv is only supported on ULT/ULX hardware.
Change-Id: I25001e97cce3193629e7fa7573bf9b352362d59b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The CMOS option system does not support negative integers. Thus, retype
and rename the option API functions to reflect this.
Change-Id: Id3480e5cfc0ec90674def7ef0919e0b7ac5b19b3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Change-Id: I9273b90b6a21b8f52fa42d9ff03a9b56eec9fcbf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
With this change, only raminit.c uses pei_data.h definitions. With MRC
cornered, making it optional is just a matter of writing a replacement.
USB config definitions will be moved to Lynx Point code in a follow-up.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: I4bc405213e9b0828d9ced18677335533c7dd381d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
For disabled USB ports, the length setting does not matter. In future
commits, disabled USB ports will end up with length field set to zero.
Change-Id: I7613e1b0c89c0b58eca790ca14fcd1633c8a93af
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
It's common to use the raw, unshifted I2C address in coreboot. Adapt
mainboards accordingly and perform the shift in MRC glue code.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: I4e4978772744ea27f4c5a88def60a8ded66520e1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51458
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Mainboards do not need to know about `pei_data` to tell northbridge code
where to find the SPD data. Adjust `mb_get_spd_map` to take a pointer to
a struct instead of an array, and update all the mainboards accordingly.
Currently, the only board with memory-down in the tree is google/slippy.
Mainboard code now obtains the SPD index in `mb_get_spd_map` and adjusts
the channel population accordingly. Then, northbridge code reads the SPD
file and uses the index that was read in `mb_get_spd_map`, and copies it
to channel 0 slot 0 unconditionally. MRC only uses the first position of
the `spd_data` array, and ignores the other positions. In coreboot code,
`setup_sdram_meminfo` uses the data of each SPD index, so `copy_spd` has
to account for this.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: Ibaed5c6de9853db6abd08f53bbfda8800d207c3e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51448
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The X11SSH-LN4F and X11SSH-F are very similiar. They both use the same
PCB and use the same Supermicro BIOS ID. The X11SSH-LN4F has 4 NICs in
difference to the X11SSH-F which only has 2 NICs. The two additional
NICs aren't populated on the X11SSH-F. Enable the PCIe root ports
connected to the two additional Intel NICs.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Change-Id: Id4e66be47ceef75905ba760b8d5a14284e130f63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: I72b717a41c5611cf578ce178722029b8646cbb35
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50539
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use global variables to provide mainboard USB settings, and have the
northbridge code copy it into the `pei_data` struct. For now.
To minimize diffstat noise, this patch does not reindent the now-global
mainboard USB configuration arrays. This is cleaned up in a follow-up.
Change-Id: I273c7a6cd46734ae25b95fc11b5e188d63cac32e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50538
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Desktop boards do not have any backlight control.
Change-Id: Ie9f5f4d7e6ae09b3d664d53e4c03157fd4ed088e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Objects that are created with acpigen need to be declared
with External () for the generation of dsdt.asl to pass
iasl without errors.
There are some objects that are common to all platforms,
and some that should be declared only conditionally.
Having a top-level ASL helps to achieve this.
Change-Id: Ibaf1ab9941b82f99e5fa857c0c7e4b6192c74330
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Having some symmetry with <soc/nvs.h> now allows to reduce
the amount of gluelogic to determine the size and cbmc field
of struct global_nvs.
Since GNVS creation is now controlled by ACPI_SOC_NVS,
drivers/amd/agesa/nvs.c becomes obsolete and soc/amd/cezanne
cannot have this selected until <soc/nvs.h> exists.
Change-Id: Ia9ec853ff7f5e7908f7e8fc179ac27d0da08e19d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lance Zhao
|
|
There's no need to have them in the devicetree. ACPI generation can now
be simplified even further, and is done in subsequent commits.
Change-Id: I3a788423aee9be279797a1f7c60ab892a0af37e7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46908
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename acpi_create_gnvs() functions under mb/ to reflect
their changed functionality.
Remove now empty mb/acpi_tables.c files.
Change-Id: Ia366867ef73d1ade9805dc29b8e14b3073f44f60
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48707
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure MAX_CPUS in SoC Kconfig with 8 as default value and remove it
from every mainboard where 8 is used.
Change-Id: I825625bf842e8cd22dada9a508a7176e5cc2ea57
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49105
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
They aren't specific to AC power operation anymore. Also adapt autoport.
Change-Id: Ib04d0a08674b7d2773d440d39bd6dfbd4359e0fb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49089
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All mainboards use the same values for AC and battery, even desktop
boards without a battery. Use the AC values everywhere and drop the
battery values. Subsequent commits will rename the AC power options
accordingly, and will also clean up the corresponding acpigen code.
This is intentional so as to ease reviewing the devicetree changes.
Also update util/autoport accordingly.
Change-Id: I581dc9b733d1f3006a4dc81d8a2fec255d2a0a0f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Configure the "POST complete" gpio in the devicetree for the BMC/IPMI
driver and set the pad's initial value to 0 since the signal is active-
high and shall be set by the IPMI/BMC driver.
Also add the pad to early gpio config, since it is expected to have an
external pull-up like X11SSM-F, which is wrong and would confuse the BMC.
Test: Boot the machine via the BMC web interface and check that sensors
get read correctly by the IPMI firmware when the payload starts.
Tested successfully.
Change-Id: If344b2271bfc8d50b8b64847109818f96f2abbcb
Tested-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Configure the "POST complete" gpio in the devicetree for the BMC/IPMI
driver.
Also add the pad to early gpio config, since it has an external pull-up,
which is wrong and would confuse the BMC. Set the pad's initial value to
zero since the "POST complete" signal is active-high and shall be set by
the IPMI/BMC driver.
Test: Boot the machine via the BMC web interface and check that sensors
get read correctly by the IPMI firmware when the payload starts.
Tested successfully.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I6409b2aca90585e44ee5d32df0ae73b259443f32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Set `bmc_jumper_gpio` to the JPB1 gpio to enable/disable BMC/IPMI
according to its value.
Test: Boot with jumper set to each enabled and disabled and check debug
log if IPMI gets enabled/disabled accordingly.
Tested successfully.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8581556d915cbad2c743a79db273479ba55798fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add a new driver for OEM commands and select it from x11-lga1151-series.
The driver communicates the BIOS version and date to the BMC using OEM
commands. The command should be supported on all X11 series mainboards,
but might work with older BMC, too.
Tested on X11SSH-TF:
The BIOS version strings are updated on boot and are visible in the
BMC web UI.
Change-Id: I51c22f83383affb70abb0efbcdc33ea925b5ff9f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: I0251d1193bb36ae73d592a0d17f580b7edaddbf6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48853
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is a whole bunch of pads being configured by the vendor firmware
that are either unconnected due to unpopulated resistor pads, only
connected to test points for vendor debugging purposes or just used as
strap. Configure them as NC with an appropriate pull to disable the
RX/TX functions.
The pads have been determined by dissecting a dead board.
This patch has been tested thoughroughly on a machine, normally used
productive, to see if any issues arise. No problems occurred at all.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I06b942e3182469f87e41914c893e5b485ccca420
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Follow vendor and enable Advanced Error Reporting for PCIe root ports.
This enabled the Linux AER driver, which handles PCIe error conditions.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I9d9b5afca0ca891e2812445db1d42a46ba16199e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48369
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the subsystem ids to PCI ports and devices, which were dumped on
vendor firmware using `lspci`.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Idb36c5c72e1b0b8303439ae5dce772822f551d2d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48368
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow vendor and enable LTR on all root ports to optimize for devices'
latency requirements and also optimize power management while preventing
failure due to wrongly guessing idle states, which happens without LTR.
Tested successfully. No errors show up in dmesg.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8f72087c71e291d2412dc7b3e16ee7f419e2ca0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48367
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All X11 boards currently supported have Intel SPS without support for
S3/S5. Thus, drop it from Kconfig.
Note: not all X11 boards are server boards. When a X11 desktop or
workstation board should be added, this can be selected by the boards,
where S3/S5 work.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ie75c9217078d38c42eba2b30c078b8bb1c2ca694
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Correct unconnected pads that are configured different currently by
copying vendor configuration while porting the board.
Add internal pull resistors to all unconnected pads, that do not have an
external pull resistor, to prevent floating.
The pads have been determined by dissecting a dead board. This commit
only changes pads, that are not connected at all and don't have any via,
so we can be absolutely sure there is no other connection.
Change-Id: I991fe270b42f430f7447712236e0f80b3d5bba2a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
(Re)configure various pads found by dissecting a dead board and vendor
firmware, as well as the BMC firmware:
- GPP_B14: input connected to jumper JBR1 - could be used to implement
"BIOS Recovery" ("Top-Block Swap") functionality; external pull-up
- GPP_C20: output to BMC alert CPU_THROTTLED# - can be used to notify
the BMC about a thermal throttling event. Not implemented in vendor
firmware.
- GPP_C23: input connected to the CPU's CATERR# output; external pull-up
Not actively used by vendor firmware.
- GPP_D1: output connected to on-board and front panel power LEDs
- GPP_D18: output connected to PERST# of both CPU PCIe Slots. Can be
used for testing/debugging only, since it resets both slots at once.
Not actively used by vendor firmware.
- GPP_D19: output connected to PERST# of both PCH PCIe Slots. Can be
used for testing/debugging only, since it resets both slots at once.
Not actively used by vendor firmware.
- GPP_D22: input connected to the BMC enable/disable jumper JPB1; Will
be used later in CB:48096 and CB:48097; external pull-up
- GPP_G0 - GPP_G3: dedicated/integrated CPU switching; probably not
useful, since the IGD is not connected to any ports on this board.
External pulls ensure correct function of a dGPU even without driving
the gpios. Not used by vendor firmware.
- GPP_G12 - GPP_G16: inputs for binary SKU_ID; external pulls
- GPP_G20: PWRFAIL# input from JPI2C1 (pin 3); external pull-up; Not
used by vendor firmware.
Also add comments for documentation. While at it, mark ME-owned pads as
reserved.
Change-Id: I9f9328e9ce6f7e291b171f776bb98bc617b64b93
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
SATA_AHCI is already the default mode for SKL/KBL based mainboards.
Therefore, remove its configuration from all related devicetrees.
Built clevo/n130wu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: Ib5222c1b0314365b634f8585e8a97e0054127fe9
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48378
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Skylake FSP isn't used by coreboot anymore. Therefore, drop the
misleading comment and the "KBLFSP" extension from the names of these
enums.
Also, drop the "MODE" extension to make their names shorter in general,
since it doesn't add any more value.
Built clevo/n130wu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: If37d40e4e1dfd11e9315039acde7cafee0ac60f0
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48377
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All four SMI/NMI interrupt inputs have an external pull-up resistor and
get triggered by pulling the line low. Thus, correct the trigger to
active-low.
Also document the signals by adding appropriate comments.
The pads' connections have been determined by dissecting a dead board.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Id1a8c1e0b9fe723a15d04a88d565a53eeba9b085
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48093
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop the NMI overrides, since NMI now gets configured in gpio common
code. Also remove the variant init mechanism, which is unused now.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I02e0c679f9aafe33108320a8dfc62dcb278202ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48092
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set the FADT PM profile to ENTERPRISE_SERVER, since the currently
supported X11 boards are server boards.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8fb5c7c262fbd3f3c085d7c2e2ef3d6ff6ce73eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48088
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rework gpio setup for the board series to not use headers but
stage-specific compilation units.
Tested successfully on X11SSM-F.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ic62ce4335af605c081ef288e892441585ff2bd3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
GPIO needs to be initialized before the IPMI device gets initialized,
so the GPIOs can be read/set by the code in CB:48096 and CB:48094. Thus,
use mainboard_ops.init for GPIO configuration instead of using the
indirection via a mainboard_enable function.
To make it more visible, that we use chip.init, rename `mainboard_init`
to `mainboard_chip_init`.
Tested successfully on X11SSM-F including the IPMI changes.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I192e69a34fa262b38bc40a95fb11c22a4041d0ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The ITSS override is not needed for LPC_CLKOUT* pads. Drop it.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I3dbbc8944751779151dcd4f92fb870d937801d69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48084
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move gpio configuration from the Fsp callback to mainboard init.
Tested successfully on X11SSM-F.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: If2a54c75c5243d94cdc025c597ee347820b35d32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48086
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop zero-value devicetree options and move PcieRpEnable options down to
the corresponding devices.
Test: built with TIMELESS=1; binaries remain identical
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I9285d786e973621a732e2627c734adc930e54207
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Drop the TODO comment, since there is no TODO left. Also drop the now
obsolete TODO section from the board documentation.
Change-Id: I4192aaedc1429c8ff1bd7c52baa4741e1df0d0c5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Time has shown that using spaces never converges into proper alignment.
Change-Id: I5338aeaf139580f9eab3e1e02cb910080a95d2c2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Most of these comments have been copy-pasted or serve no purpose other
than to eventually turn into misleading info. While the description of
the first 120 bits of CMOS could be useful, it should instead be added
to the documentation for the CMOS option infrastructure, or /dev/null.
Moreover, trim down newlines to no more than two consecutive newlines.
Change-Id: I119b248821221e68c4e31edba71ba83b7d2e14e9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Change-Id: I50390f66d9570eb0fd703e3ad8a2735125d76b61
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47566
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I5b6191d2b5f6fd6d127934eda56e3c24181b0c4c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47565
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, Google Wolf remains identical.
Change-Id: I710581156937b042ba4cf5948c65d0795ad37bbf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46789
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The other two modes are not used by any mainboard, and the code seems to
be copied from older southbridges. As the code looks incorrect, drop it.
Change-Id: I374546279a85cead1aea13e0952bbfd6f643a75b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The dt option `speed_shift_enable` is obsolete now. Drop it.
Change-Id: I5ac3b8efe37aedd442962234478fcdce675bf105
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Following commit f50ea988b a couple of symbols are gone, so follow up
that change for this board as well.
Change-Id: I09fd3a107447eb45bb46b7f0f821377943f140b2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46621
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Get rid of legacy pad macros by replacing them with their newer
equivalents.
TEST: TIMELESS-built board images match
Change-Id: I078f9bb3c78f642afc6dcfd64d77be823a4485c2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This adds another X11 series board, the X11SSH-F, which is similiar to
X11SSH-TF but differs in PCIe interfaces/devices, ethernet interfaces.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: I92c32bff861f0b5697aea52ff282fae76b3b78ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
There's no need to have multiple Kconfig symbols which do the same
thing. Introduce `SUPERIO_NUVOTON_COMMON_COM_A` and update boards to use
the new symbol. To preserve alphabetical order in mainboard Kconfig,
place the new symbol above the Super I/O symbol (instead of below).
Change-Id: Ic0a30b3177a1a535261525638be301ae07c59c14
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46522
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I5a5f4e7067948c5cc7a715a08f7a5a3e9b391191
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This patch moves platform.asl into common block acpi directory to
avoid duplicating the same ASL code block across SoC directory.
TEST=Able to build and boot TGL, CNL and CML platform.
1) Dump and disassemble DSDT, verify _PIC method present inside
common platform.asl is still there.
2) Verify no ACPI error seen while running 'dmesg` from console.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I5189b03d6abfaec39882d28b40a9bfa002128be3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I1aae6c0291ad329c8cc125cd18ba22dfd63d979b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Setting USBx_PORT_EMPTY is not a requirement anymore, since unset
devicetree settings default to 0 and the OC pin now only gets set when
the USB port is enabled (see CB:45112).
Thus, drop the setting from all devicetrees.
Change-Id: I899349c49fa7de1c1acdca24994ebe65c01d80c6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
CPU_INTEL_HASWELL is already selected at nb/intel/haswell/Kconfig.
Change-Id: I608286aae72bc740be642a72109472fb235f37bf
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
GENERATE_SMBIOS_TABLES is already set to yes at src/Kconfig
Change-Id: I2845f4f329283360a49ea40dfee7d9a232ab4ea1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Change-Id: I6afea5c102299e570378a1656d3dcd329a373399
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44093
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, SDXC gets enabled by the option ScsSdCardEnabled,
but this duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the SDXC controller.
All corresponding mainboards were checked if the devicetree
configuration matches the ScsSdCardEnabled setting, and missing
entries were added.
Change-Id: I298b7d0b0fe2a7346dbadcea4be22dc67fce4de8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Currently SA thermal subsystem gets enabled by the option Device4Enable,
but this duplicates the devicetree on/off options. Therefore depend on
the devicetree for enablement of the SA thermal subsystem controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Device4Enable setting, and missing entries
were added.
Change-Id: I7553716d52743c3e8d82891b2de14c52c6d8ef16
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44026
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
They default to zero already, so we might as well drop them.
Tested with BUILD_TIMELESS=1, its coreboot.rom does not change.
Change-Id: I3c04240b270f51d584f879e1344301679f133fdb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43928
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently eMMC gets enabled by the option ScsEmmcEnabled, but this
duplicates the devicetree on/off options. Therefore use the
on/off options for the enablement of the eMMC controller.
I checked all corresponding mainboards if the devicetree configuration
matches the ScsEmmcEnabled setting.
Change-Id: I3b86ff6e2f15991fb304b71d90c1b959cb6fcf43
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Currently SMBus gets enabled by the option SmbusEnable, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the SMBus controller.
I checked all corresponding mainboards if the devicetree configuration
matches the SmbusEnable setting.
Change-Id: I0d9ec1888c82cc6d5ef86d0694269c885ba62c41
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Currently SATA gets enabled by the option EnableSata, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the SATA controller.
I checked all corresponding mainboards if the devicetree configuration
matches the EnableSata setting.
Change-Id: I217dcb7178f29bbdeada54bdb774166126b47a5a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Add interrupts for all enabled superio devices to quiet the warning
about missing interrupts in devicetree.
Vendor uses interrupt 0x00 for all devices except SUART* and KBC, so
let's do that, too. This also changes SWC from 0x0b to 0x00.
Verified with superiotool on X11SSM-F.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I7a6dc7345f020e53415a7d0d104ce93ab4b194fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonas Löffelholz
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
All boards disable PIRQs. They aren't used on modern OSes anyway.
Change-Id: I1351fd4a3910e8cf2e9afe51dc2e82c7464de403
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
If bit 7 of a PIRQ route is set, it is disabled. Modern OSes don't use
PIRQ routing, so we might as well zero the other bits for consistency.
Tested on Asrock B85M Pro4 with SeaBIOS 1.13.0, still boots.
Change-Id: I78980b9ea5e878a6200df0f6c18c5e7d06a7950a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43861
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Put them in common code just in case something depends on the values.
Change-Id: Ief526efcbd5ba5546572da1bc6bb6d86729f4e54
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43851
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- remove comments (except the GPIO group), because it does not contain
useful information that helps to understand the circuit, which we do
not have;
- remove empty lines between macros;
- use a shorter PAD_CFG_GPI_INT() macro instead of
PAD_CFG_GPI_TRIG_OWN() to set DRIVER mode.
Change-Id: Ia7111341aab6f400da70d936849e4d4c9406905b
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Converts bit field macros to target PAD_CFG_*() macros, which were
hidden in the comments. To do this, the following command was used:
./intelp2m -n -t 1 -p snr -file ../../src/mainboard/supermicro/
x11-lga1151-series/variants/x11ssm-f/include/variant/gpio.h
./intelp2m -n -t 1 -p snr -file ../../src/mainboard/supermicro/
x11-lga1151-series/variants/x11ssh-tf/include/variant/gpio.h
This is part of the patch set
"mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m":
CB:42916 - 1/4 Decode raw register values
CB:42917 - 2/4 Exclude fields for PAD_CFG
CB:42918 - 3/4 Fixes some field macro
CB:35679 - 4/4 Convert field macros to PAD_CFG
Tested with BUILD_TIMELESS=1, Supermicro X11SSH-TF and X11SSM-F,
remains identical.
Change-Id: Idad7536854d4b1ae7dcf7934e81de438478fe059
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35679
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fixes some bit fields to convert to target macros PAD_CFG_*() macros.
This is part of the patch set
"mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m":
CB:42916 - 1/4 Decode raw register values
CB:42917 - 2/4 Exclude fields for PAD_CFG
CB:42918 - 3/4 Fixes some field macro
CB:35679 - 4/4 Convert field macros to PAD_CFG
Change-Id: I291f5f0f34505c466b610aa4049c8cc35937d140
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42918
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch excludes bit fields that should be ignored [1] in order
to convert current macros to target PAD_CFG_*() macros. The following
commands were used for this:
./intelp2m -ii -fld cb -ign -t 1 -p snr -file ../../src/mainboard/
supermicro/x11-lga1151-series/variants/x11ssm-f/include/variant/gpio.h
/intelp2m -ii -fld cb -ign -t 1 -p snr -file ../../src/mainboard/
supermicro/x11-lga1151-series/variants/x11ssh-tf/include/variant/gpio.h
[1] ignore RX Level/Edge Configuration (bit 26:25) and RX/TX Buffer
Disable (bit 9:8) for the native function, because it does not
affect the pad in this mode.
This is part of the patch set
"mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m":
CB:42916 - 1/4 Decode raw register values
CB:42917 - 2/4 Exclude fields for PAD_CFG
CB:42918 - 3/4 Fixes some field macro
CB:35679 - 4/4 Convert field macros to PAD_CFG
Change-Id: Icdf366a8d416598cec5afcb9a0fae6bf7ecd7ba0
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42917
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the intelp2m utility [1,2] with -fld=cb options to convert the pad
configuration format with the raw values of the DW0 and DW1 registers
to the format with the bit fields macros: PAD_FUNC(), PAD_RESET(),
PAD_TRIG(), PAD_BUF(), PAD_PULL(), etc... Also use the -ii options to
generate the target macro in the comments, so that it is easier to
understand what result we should get:
./intelp2m -ii -fld cb -t 1 -p snr -file ../../src/mainboard/supermicro/
x11-lga1151-series/variants/x11ssm-f/include/variant/gpio.h
./intelp2m -ii -fld cb -t 1 -p snr -file ../../src/mainboard/supermicro/
x11-lga1151-series/variants/x11ssh-tf/include/variant/gpio.h
[1] https://github.com/maxpoliak/pch-pads-parser
[2] https://review.coreboot.org/c/coreboot/+/35643
This is part of the patch set
"mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m":
CB:42916 - 1/4 Decode raw register values
CB:42917 - 2/4 Exclude fields for PAD_CFG
CB:42918 - 3/4 Fixes some field macro
CB:35679 - 4/4 Convert field macros to PAD_CFG
Tested with BUILD_TIMELESS=1, Supermicro X11SSH-TF and X11SSM-F,
remains identical.
Change-Id: I209ecdca75a0e62233d3726942c75ea06acc40a2
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42916
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This code is not even being build-tested. Drop it before it grows moss.
Change-Id: I65fedfa7e8b2fbb72b3109a8790445e38909976a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
There's no generic way to tell whether a mainboard has an EC or not.
Making Kconfig symbols for these options seems overkill, too. So, just
put them on the devicetree. Also, drop unnecessary assignments when the
board's current value is zero, as the struct defaults to zero already.
Change-Id: If2ebac5fcab278c97dfaf8adc9d1e125888acafe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43129
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
And use it instead of directly writing to the MRC struct.
Change-Id: I7f04db29a08512c1a8b2b2300dba71cb3b84a5c5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
Check the PCH's LPC device ID to know the system type instead of relying
on hardcoded numbers. The `get_pch_platform_type` function is MRC-safe.
Change-Id: Icfe7c2dccb7c7a178892ad3a2e34ca93b33b2bb9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43124
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This Kconfig symbol allows doubling the memory's refresh rate, assuming
that the MRC actually cares about it. It is disabled by default except
on the mainboards which explicitly enabled this setting in `pei_data`.
Change-Id: I6318dad0350d1c506c67f9d117d0ae8dad871281
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
