| Age | Commit message (Collapse) | Author |
|---|
|
Configure the "POST complete" gpio in the devicetree for the BMC/IPMI
driver.
Also add the pad to early gpio config, since it has an external pull-up,
which is wrong and would confuse the BMC. Set the pad's initial value to
zero since the "POST complete" signal is active-high and shall be set by
the IPMI/BMC driver.
Test: Boot the machine via the BMC web interface and check that sensors
get read correctly by the IPMI firmware when the payload starts.
Tested successfully.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I6409b2aca90585e44ee5d32df0ae73b259443f32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Set `bmc_jumper_gpio` to the JPB1 gpio to enable/disable BMC/IPMI
according to its value.
Test: Boot with jumper set to each enabled and disabled and check debug
log if IPMI gets enabled/disabled accordingly.
Tested successfully.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8581556d915cbad2c743a79db273479ba55798fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Follow vendor and enable Advanced Error Reporting for PCIe root ports.
This enabled the Linux AER driver, which handles PCIe error conditions.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I9d9b5afca0ca891e2812445db1d42a46ba16199e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48369
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the subsystem ids to PCI ports and devices, which were dumped on
vendor firmware using `lspci`.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Idb36c5c72e1b0b8303439ae5dce772822f551d2d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48368
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow vendor and enable LTR on all root ports to optimize for devices'
latency requirements and also optimize power management while preventing
failure due to wrongly guessing idle states, which happens without LTR.
Tested successfully. No errors show up in dmesg.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8f72087c71e291d2412dc7b3e16ee7f419e2ca0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48367
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop zero-value devicetree options and move PcieRpEnable options down to
the corresponding devices.
Test: built with TIMELESS=1; binaries remain identical
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I9285d786e973621a732e2627c734adc930e54207
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add interrupts for all enabled superio devices to quiet the warning
about missing interrupts in devicetree.
Vendor uses interrupt 0x00 for all devices except SUART* and KBC, so
let's do that, too. This also changes SWC from 0x0b to 0x00.
Verified with superiotool on X11SSM-F.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I7a6dc7345f020e53415a7d0d104ce93ab4b194fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonas Löffelholz
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I02979a0632a7b356985f96c3ba239daba178b4e3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39989
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix PNP warning about missing devicetree entry for SUART1/2 by setting
register 0xF0 to a sane (default) value.
Change-Id: Ie852696aae09b9b03cebd6c3d8cbbd53a7138d89
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
SUART3/4 are unused on this board (verified by checking registers on
vendor BMC firmware). Further they break the console for an unknown
reason. Thus disable them.
Change-Id: I30bb8184d03ee1037d9ec33eb1d93ee540563fc5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38818
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds another x11 series board, the X11SSM-F, which is similiar to
X11SSH-TF but differs in PCIe interfaces/devices, GPIO settings and
Ethernet interfaces.
Change-Id: I24e6f0f41a844652f88b562285b26beef311a2c9
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Michael Niewöhner
|
