| Age | Commit message (Collapse) | Author |
|---|
|
Change-Id: I46a362270f69d0a4a28e5bb9c954f34d632815ff
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81455
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This changes the location to be expressed as a combination of ORs. This
allows aliases for special locations.
For example, `AZALIA_REAR_PANEL` is easier to read than
`AZALIA_EXTERNAL_PRIMARY_CHASSIS, AZALIA_SPECIAL7`.
References:
- Intel High Definition Audio Specification, rev. 1.0a, page 180,
Table 110. Location.
Change-Id: I5a61a37ed70027700f07f1532c500f04d7a16ce1
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
We were keeping 2 copies of the same thing (albeit there were some
slight differences). As azalia_device.h is used much more in the
codebase this was kept as the base and then some of the nice features
of azalia.h were incorporated.
The significant changes are:
- All enum names now use the `AZALIA_` prefix.
This also drops the AzaliaPinConfiguration enum as it was never used
since added in 2013.
Change-Id: Ie874b083a18963679981a9cd2b25d123890d628e
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80695
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: Ied455ff29b151fb5f4bca26a189b1d4104d8cede
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80595
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This renames bus to upstream and link_list to downstream.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I80a81b6b8606e450ff180add9439481ec28c2420
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
As a result of hardware changes on this board, the PHY previously
routed to the PSE GbE 1 is now routed to PSE GbE 0 on the Elkhart Lake
SoC.
This patch changes the device PCI ID in the board's devicetree and
accordingly, the GPIO configuration.
BUG=none
TEST=Boot into Linux and observe whether both PSE GbE 0 and PCH GbE
are working, while PSE GbE 1 remains inactive (not listed by 'ip link')
.
Change-Id: I322371f944d15134e6f48ecd84a4026c2fced27b
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The currently used panel type could work with 500 ms but increasing
the value to 1 second allows to use a wider range of LVDS LCD panels,
as many of them specify the delay of 1 s as minimum.
The patch has already been made for mc_ehl3 and serves the purpose of
standardization.
commit c0221aa980d3 ("mb/siemens/mc_ehl3/lcd_panel.c: Set LVDS re-power
delay to 1 s")
Change-Id: Ife26ff27b41298ceeed7d9aed0c1ae5553ab5ff8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib69236fb5d68272f92405512dc231fa75ecccaa6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I4790adb41cb62c8c8dd44261a2926dfb6350955a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80111
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
Use the references from the chipset devicetree as this makes the
comments superfluous.
Change-Id: Ic3a4c85ec6bfdc858f9b6f79b114cf612ad3a153
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80022
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The PcieRpEnable option is redundant to our on/off setting in the
devicetrees. Let's use the common coreboot infracture instead.
Thanks to Nicholas for doing all the mainboard legwork!
Change-Id: I11c3c45eae0e1451d5c54c17b7e60300dedda8fa
Signed-off-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The address space of possible SPD-EEPROMs 0x50..0x53 on the SMBus
interface is per default write-protected in FSP. This avoids that an
SPD-EEPROM on a DRAM module gets overwritten by the host.
On mc_ehl1, memory-down configuration is used and there is no SPD EEPROM
available. Nevertheless, there is a general purpose EEPROM on the same
address available which needs to stay writeable.
This patch disables the default-enabled write protect feature for the
SPD-EEPROM addresses just for mc_ehl1.
Test=Boot into Linux and make sure a write access into the EEPROM is
possible.
Change-Id: I6b0fcdbeb0dbf971cfdceb70d6f4845765a3bdb6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
With the latest hardware revision of both mainboards, native function
two of GPIO B23 (PCHHOT_N) is used for diagnostic purposes.
BUG=none
TEST=Checked output verbose GPIO debug messages
Change-Id: Ibe130b5d4c74576294183221765c5f4db9b5ec2a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78962
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: Ic199a60013ceedfd15b191a5fe707be6654ad3a2
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75078
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The connected panel on this mainboard gets the PWM frequency directly
from the Elkhart Lake CPU. The PWM controls the brightness of the
backlight. Therefore, it is necessary to activate the PWM passthrough
mode in the PTN3460 eDP-to-LVDS bridge (see PTN3460 Programming Guide -
5. Configuration Registers).
Link to PTN3460 Programming Guide:
https://web.archive.org/web/20230908074244/https://www.nxp.com/docs/en/application-note/AN11128.pdf
BUG=none
TEST=Boot into Linux and change the brightness of the screen
Change-Id: Ia0a329426e585b6243c8888806befbe4f6ec2998
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
The connected panel on this mainboard gets the PWM frequency directly
from the Elkhart Lake CPU. The PWM controls the brightness of the
backlight. Therefore, it is necessary to activate the PWM passthrough
mode in the PTN3460 eDP-to-LVDS bridge (see PTN3460 Programming Guide -
5. Configuration Registers).
Link to PTN3460 Programming Guide:
https://web.archive.org/web/20230908074244/https://www.nxp.com/docs/en/application-note/AN11128.pdf
BUG=none
TEST=Boot into Linux and change the brightness of the screen
Change-Id: Iec9d8ae22fced40c45e5bfa8989ad655a722d7ef
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77702
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The board uses soldered down LPDDR4, so process their SPD files, and add
the SPD for Micron MT53E512M32D1NP-046WTB provided by Micron.
Signed-off-by: Johannes Hahn <johannes-hahn@siemens.com>
Change-Id: I978b7450b106b86eef322df8b33df41e038599eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77349
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
With the introduction of a new Linux version a problem has appeared
after a software initiated reset via CF9h register. The problem
manifests itself in the fact that the Linux kernel does not start after
the reboot. The problem is solved by setting bit 3 to 1 in Reset Control
Register (I/O port CF9h). This leads to the fact that the PCH will drive
SLP_S3 active low in the reset sequence. It leads to the same behavior
as in commit 04ea73ee78bc ("siemens/mc_apl3: Set Full Reset Bit into
Reset Control Register") explained.
Change-Id: Ibc6d538c939e38732f42995d5ec6c8b61f979a6a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77603
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Delete this RTC from the configuration as fa_ehl mainboard
uses a different real time clock.
Signed-off-by: Johannes Hahn <johannes-hahn@siemens.com>
Change-Id: Ifd6b68d05a094cb4c890f1ffce62d89b771e23c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
|
|
The mainboard currently does not make use of a dedicated TPM.
Although it has one assembled. This TPM is not connected
via LPC hence it is turned off in the devicetree.
Signed-off-by: Johannes Hahn <johannes-hahn@siemens.com>
Change-Id: I96cc38c3812d76d654339ad5b2b7f88fd1327779
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77351
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
fa_ehl mainboard does not make use of the SIEMENS NC_FPGA
as it is not placed on this board.
Signed-off-by: Johannes Hahn <johannes-hahn@siemens.com>
Change-Id: I5f1f796e4339ba37d461d6818c2bb6ba028b89c2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
Add a new mainboard called fa_ehl which is based on Siemens's
'mc_ehl2'. This commit simply copies the mainboard directory and
adjusts the naming to match the new board's name. Moreover a variants
scheme is provided for possible alternative implementations. Follow-up
commits will introduce the needed changes for the new mainboard.
Change-Id: Ia389c8812d14db8b663547e6336e900becbc8be6
Signed-off-by: Johannes Hahn <johannes-hahn@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76444
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
|
|
To help identify the licenses of the various files contained in the
coreboot source, we've added SPDX headers to the top of all of the
.c and .h files. This extends that practice to Makefiles.
Any file in the coreboot project without a specific license is bound
to the license of the overall coreboot project, GPL Version 2.
This patch adds the GPL V2 license identifier to the top of all
makefiles in the mainboard directory that don't already have an SPDX
license line at the top.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ic451e68b1ad9ccdf34484dd98bd7fca7e177ef22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68982
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
With the latest hardware revision, the polarity of GPP_B5 has been
changed. For a full-populated DRAM configuration, the input signal is
now connected to 3.3 V and for a half-populated configuration it is
connected to ground.
BUG=none
TEST=Use different populated mainboards and check coreboot log
GPP_B5 = 0:
[INFO ] meminit_channels: DRAM half-populated
[DEBUG] 1 DIMMs found
GPP_B5 = 1:
[DEBUG] 2 DIMMs found
Change-Id: Iaa3a63fa52c802d8f5d8c6cc11dd6edfac117e88
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76434
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO GPP_B5 is used as input on this mainboard. For a full-populated
DRAM configuration, the input signal is connected to ground and for a
half-populated configuration it is connected to 3.3 V.
BUG=none
TEST=Use different HW configurations and check coreboot log
GPP_B5 = 0:
[DEBUG] 2 DIMMs found
GPP_B5 = 1:
[INFO ] meminit_channels: DRAM half-populated
[DEBUG] 1 DIMMs found
Change-Id: I48b4a3bea7f1ff804b78b7c648a7ea1925627b8a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76245
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
There can be mainboard variants, which are only equipped with
half-populated DRAM. For this reason, the meminit parameter for
populatation should be adjustable. The default setting remains at
full-populated DRAM. At mainboard variant level a different selection
via individual input paths can be made.
Change-Id: I390bbfa680b5505bb2230fa0740720bd9dd1fafb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76244
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It's been decided not to use any of the USB 3.0 ports on this board.
This patch disables the remaining USB 3.0 port 0, after the port 1
has already been disabled in commit d0627c7595fe
("mb/siemens/mc_ehl3/devicetree.cb: Disable USB 3.0 port 1").
BUG=none
TEST=None of the USB 3.0 ports functional anymore after boot,
the USB 2.0 ports continue working.
Change-Id: I28465f1c5e6d3167c649da898ec60d8bb97093e2
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75836
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With the previous instruction the complete register was set to '0'.
Correctly, only the bits 23:16 must be masked.
Change-Id: Idd6e70dcb42c69cf3bc5d36db993e6def52eba58
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76177
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
Because of an incorrect transmit voltage swing, the signal must be
adjusted. The factor of slices for full swing level can be corrected via
the High Speed I/O Transmit Control Register 3. The appropriate value of
0.7 V was determined by using an oscilloscope.
Change-Id: I965960004ca44f1b37b16ce6484000fa7fd8ad90
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The offset '0xa8c' for the High Speed I/O Transmit Control Register 3
refers to SATA port 1 only. To make this clear, change the name of the
define from 'TX_DWORD3' to 'TX_DWORD3_P1'.
Change-Id: I09d17eeffbe84939297e739586f6b74ed3e2258b
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76174
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
A correction of Tx signal from SATA interface is not necessary on these
boards currently. Therefore remove the define and the corresponding code
on mc_apl5.
Change-Id: I5092ee128cb35e126069d18bb3cbd635e01bbcdb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'DisableSataSalpSupport'.
Change-Id: I4a68ffd2b68c92434da681b5e5567329c8784c72
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75858
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It's been decided not to use the USB 3.0 port 1 on this board anymore,
so disable it also with the corresponding USB 2.0 lane.
BUG=none
TEST=USB 3.0 port 1 not functional anymore after boot, while others
continue working.
Change-Id: I2799e3d9d7232743c9480dd9611d94ed3249f53b
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'SataPortsEnable'.
Change-Id: I0df35125360eb42a03d5445011d72842cb2b8d7e
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75553
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
There are only SSD connected to SATA ports on this mainboard. To prevent
misbehavior, set the correct hard drive type for enabled SATA ports.
BUG=none
TEST=Boot into OS and check the stability of the SSD
Change-Id: I2c2b0548865e87859a1d742295e09a731bfb3f76
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
Due to mainboard restrictions a SATA link at Gen 3 can cause issues as
the margin is not big enough. Limit SATA speed to Gen 2 to achieve a
more robust SATA connection.
Change-Id: Ifdea4542836b9c75b5507324fbb06b9566a6fe1d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75365
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add devicetree and Kconfig entries to enable additional configuration
of the Pericom PI7C9X2G608GP PCIe switch on this board variant.
The amplitude is being adjusted to 425 mV and de-emphasis level to
6.0 mV.
BUG=none
TEST=Read out the PCIe config space values of the switch and check if
they match with the ones configured over SMBus.
Change-Id: I11459f0794278ad614aa6e16c56df1ad578fe2f8
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
To improve the rate of data transfer for PCIe root port #2 (00:1c.1) and
root port #3 (00:1c.2) set the max payload size to 256 bytes for both
root ports.
Change-Id: I553f6cf090d799fbbaafb925646c6566d6951a86
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75127
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
|
|
This mainboard contains in addition to its base variant, mc_ehl2, an LCD
panel driven through the PTN3460 eDP-to-LVDS bridge.
This patch enables the PTN3460 support by adding the device to
devicetree.cb and board-specific configuration parameters in
lcd_panel.c.
BUG=none
TEST=Boot with the LCD panel attached and observe whether the picture is
stable and free of artifacts coming from wrong resolution and timing.
Change-Id: I196d7ceeb7ac241c9b95db2ef791a5f3ff7890a7
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard is based on mc_ehl2. In a first step, it contains a copy
of mc_ehl2 directory with minimum changes. Special adaptations for
mc_ehl5 mainboard will follow in separate commits.
Change-Id: Id80f8eb49dd2fed0ed1ffc479d47d8669eca84c9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With the introduction of a new Linux version a problem has appeared
after a software initiated reset via CF9h register. The problem
manifests itself in the fact that the Linux kernel does not start after
the reboot. The problem is solved by setting bit 3 to 1 in Reset Control
Register (I/O port CF9h). This leads to the fact that the PCH will drive
SLP_S3 active low in the reset sequence. It leads to the same behavior
as in commit 04ea73ee78bc ("siemens/mc_apl3: Set Full Reset Bit into
Reset Control Register") explained.
Change-Id: Ia8b7f997ca6234add569da751e1070144790e258
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: I6578aee52e6900b25441dc119383856acc480231
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
An underscore has crept into the mainboard model option for mc_ehl3 and
mc_ehl4 by mistake. This patch fixes the incorrect entry.
Change-Id: Ie59619877fb6341a5bbfe91c13e7692943480ad0
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75040
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are only SSD connected to SATA ports on this mainboard. To prevent
misbehavior, set the correct hard drive type for enabled SATA ports.
BUG=none
TEST=Boot into OS and check the stability of the SSD
Change-Id: I116b1e36f0582956604c3c2508961ffb3de0898a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74947
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Since commit 833bb448c521 ("mb/siemens/mc_ehl: Remove spd.bin from
CBFS"), the subdir 'spd' is no longer necessary.
Change-Id: Ibaf44e3181b2167aa83cffcc59835196e4cb5cdb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The support for a spd.bin from CBFS was removed for all mc_ehl boards in
commit 833bb448c5213 (mb/siemens/mc_ehl: Remove spd.bin from CBFS).
There is still a remaining comment in romstage_fsp_params.c referring to
the removed capability. This fix removes the spd.bin related part of the
comment to stay consistent with the code.
Change-Id: I669ee1c33d1d1c47764640982f71129195e63f14
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74801
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard has SD slot available and therefore it should be enabled.
Use the same SD card configuration as for mc_ehl2 mainboard.
Change-Id: Icd9b25301311679cf93b05ba83a24e551261a020
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard has the RTC RV-3028-C7 connected to the I2C1.
TEST:
- Console Log shows no errors for RV-3028-C7 during I2C1 init
- Finalize device for I2C 00:52 shows correct date and time
Change-Id: I1b4115d7844a0c218fdf92cb1af2da5a95eb4337
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74652
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct the USB settings, suitable for this mainboard.
Change-Id: I943eb891e2f2d967acfd441c085063dbad49e993
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74651
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since mc_ehl4 was only a copy of mc_ehl1 in a first step, the default
value of the Kconfig switch EARLY_PCI_BRIDGE_FUNCTION must be set to
'0'. On this mainboard NC FPGA is connected to PCIe root port #1
(00:1c.0).
Change-Id: I15035523d8575d486c3f2d0ffe3916712ee89d7d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Since mc_ehl4 was only a copy of mc_ehl1 in a first step, the GPIOs must
be adjust according to the circuit diagram for this mainboard.
Change-Id: I66bfbb380e9a05b3a2c08d5d1980e9749b46ee43
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With the latest hardware revision, the two GPIOs GPD11 and GPP_C8 are no
longer used.
BUG=none
TEST=Checked output verbose GPIO debug messages
Change-Id: Ia06f93aee4eccb0e4230f0c3ef53922d42701f21
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74201
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The default SPD size is set to 256 bytes, instead of 512 for
LPDDR4/DDR4 if not overridden by the mainboard Kconfig. This caused
the SMBus libraries to read only the lower half of the DIMM SPD on
protectli/vault_ehl. The lower half of the SPD passed to FSP causes
a bug in DIMM change detection, which relies on the CRC of the
manufacturer bytes in the upper half of the SPD (CRC of zero bytes
always gives zero so no change was assumed). Setting the DIMM SPD size
to 512 fixes it.
Setting the SPD size in SoC will also avoid such problems in the future
Elkhart Lake ports. Elkhart Lake supports only LPDDR4/DDR4 so providing
the correct default of 512 bytes is an obvious thing to do.
TEST=Boot Protectli VP2420 (vault_ehl) with different DIMMs and see
FSP is retraining the memory instead of doing the fastboot with old
DIMM data.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I998ed8781951034419cadc26c04ff1e0a124b267
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73933
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to a non-optimal RX signal (receive) on PCIe root port #4 (00:1c.3)
and #5 (00:1c.4), the speed must be limit to Gen 1.
BUG=none
TEST=RX signal measured with oscilloscope
Change-Id: I695c0ef961290676fe421b6efd631d6e94d6d556
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73767
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
Correct the remaining PCI devices, differing from the ehl1 mainboard.
Change-Id: Ie09188b72a62c4d5cba2fcda6f60f3bc0098633e
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
As discused earlier, the callback name 'mb_adjust_cfg' was considered
too generic. The new naming is chosen to be consistent with other
drivers' callback names designed to be used at mainboard level.
Also other functions, namely 'mb_get_edid' and 'mb_select_edid_table'
are renamed accordingly.
BUG=none
TEST=Builds for siemens/mc_apl{1,4,5,7} and siemens/mc_ehl boards
complete successfully.
Change-Id: I4cbec0e72e5f03e94df0faa36765d1a6cd873a7a
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
There were two wrong comments in all mc_ehl gpio.c files. This patch
corrects the incorrect comments.
Change-Id: Iea356db177227d89b91be32a4e2367c612b77350
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72458
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mainboard does not use security features like TPM.
Change-Id: Ieebbf12fc844573ffadb089da78062dd2033517a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The upcoming mc_ehl4 variant is the first Siemens Elkhart Lake mainboard
without a TPM. For this reason, the corresponding Kconfig switches must
be moved to variant level. To prevent Jenkins build from complaining,
the TPM is removed in the following patch.
Change-Id: Ic73ccd1b52e57c1cf1dd7337b0e28beaadbece8e
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Measurements have shown that the automatic calibrated values for RGMII
output impedances are too low. For this reason, set the PMOS value to 16
and the NMOS to 13.
Change-Id: Ic3382889d3281faccb03819f9680a9763703b2a1
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73019
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mainboard is based on mc_ehl1. In a first step, it contains a copy
of mc_ehl1 directory with minimum changes. Special adaptations for
mc_ehl4 mainboard will follow in separate commits.
Change-Id: I3c1f2cf4a3dcae58895f6d14a7fce46b2825e6ba
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72427
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With the latest hardware revision, the two GPIOs GPP_B15 and GPP_E19 are
no longer connected to a native function.
BUG=none
TEST=Checked output verbose GPIO debug messages
Change-Id: I266612f041b749aa83b366497b4211fc075c7bd7
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The currently used panel type could work with 500 ms but increasing
the value to 1 second allows to use a wider range of LVDS LCD panels,
as many of them specify the delay of 1 s as minimum.
BUG=none
TEST=Test link stability using a panel with minimum re-power delay of
1 s.
Change-Id: I2dd86e791c1212b67a80d7e6cfc474ad91b26c6b
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: I7eaf625e5acfcefdae7c81e186de36b42c06ee67
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Contents of the EDID are passed by a reference to an array
of length 0x80, for which the macro 'PTN_EDID_LEN' has already
been around.
This patch makes use of this macro within the driver and mainboard
implementation utilizing it.
BUG=none
TEST=A successful build of mc_apl{1,4,5,7} and mc_ehl3 mainboards.
Change-Id: If7d254aaf45d717133bb426bd08f8f9fe5c05962
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Change-Id: Id8e1a52279e6a606441eefe30e24bcd44e006aad
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69815
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
Since the PSE GBE0 MAC has been disabled on this board in
commit 343644006f89 ("mb/siemens/mc_ehl3/devicetree.cb:
Remove TSN GbE 0"), therefore disable the corresponding
GPIOs as well.
BUG=none
TEST=Test link detection and IP assignment on the remaining
ports (PSE GBE1 and PCH GBE0) of mc_ehl3.
Change-Id: Ifa055f58894688471d68b9b93fcb994fdcb2a568
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72449
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The parallel mp code picks up lapics at runtime, so remove it from all
devicetrees that use this codebase.
Change-Id: I5258a769c0f0ee4bbc4facc19737eed187b68c73
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69303
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Return generic coreboot error codes from the mb_adjust_cfg
callback used in mainboards instead of '-1' constant and
a driver-specific success-indicating define.
BUG=none
TEST=Boards siemens/mc_apl{1,4,5,7} and siemens/mc_ehl3
build correctly.
Change-Id: I5e0d4e67703db518ed239a845f43047f569b94ec
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Enable early POST code display on this variant using
the common mc_apl1 baseboard functionality.
BUG=none
TEST=Boot on mc_apl5 and observe that POST codes are
displayed before DRAM training.
Change-Id: I390e0ab09ca830637e7a991db77e994d6c358e75
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72386
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable early POST code display on this variant using
the common mc_apl1 baseboard functionality.
BUG=none
TEST=Boot on mc_apl6 and observe that POST codes are
displayed before DRAM training.
Change-Id: I2a52c241c383f8ebcf05052e9bc0ba13e63e3728
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Move logic previously used only in the mc_apl2 variant to
the mainboard level so that other variants can also make
use of it without code duplication.
This functionality on the mc_apl6 variant will be enabled
in a follow-up patch.
BUG=none
TEST=Boot on siemens/mc_apl2 and observe that the POST
codes are displayed before DRAM training.
Change-Id: I762e328ad06c047d911ce1fc40f12a66cbd14e11
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With the addition of the mc_ehl3 board variant, a few
points about commenting the code arose either from the
review or during the implementation itself.
This patch unifies structure of these files, which
have a similar structure across more Siemens boards
utilizing the PTN3460 eDP-to-LVDS bridge.
BUG=none
TEST=Check that images for the affected boards can be
built.
Change-Id: I59820362e1f87e296c5548b9c3cecba4d2710fe7
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72068
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This board contains in addition to its base variant, mc_ehl2,
an LCD panel driven through the PTN3460 eDP-to-LVDS bridge.
This patch enables the PTN3460 support by adding the device to
devicetree.cb and board-specific configuration parameters in
lcd_panel.c, based upon a similar implementation in siemens/mc_apl7.
BUG=none
TEST=Boot with the LCD panel attached and observe whether
the picture is stable and free of artifacts coming from wrong
resolution, timing etc.
Change-Id: Ib8a1a6f47053406e42554c2dd33684165d54be08
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The {read,write}{16,32}() functions used in this file come from the
mmio.h header, so include it directly.
BUG=none
TEST=Read out the SD card controller (device 1a.1) PCI registers
in Linux and check whether the values reflect the ones defined
in this file.
Change-Id: Iff7b55ef2bf98371b7d7d9114ccf3ebed64772a2
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72009
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change MAINBOARD_PART_NUMBER Kconfig value for mc_ehl3
from "MC_EHL3" to "MC EHL3".
Change-Id: Ie548607c5fb62faaed4921af714bc9b912e558a8
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71775
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
<gpio.h> chain-include <soc/gpio.h>.
Change-Id: Ia57d5cd33c70b6a755babd4db56c64c0e3666f9f
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enable the real-time tuning to improve performance in the real-time
environment for this mainboard.
Change-Id: I91ad7ca58add92b5cc66148aff8378890ee217eb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71234
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to mainboard restrictions a SATA link at Gen 3 (6 Gbps) can cause
issues as the margin is not big enough. Limit SATA speed to Gen 2 to
achieve a more robust SATA connection.
Change-Id: Ia79998db5f959528a4e8e29e570a7f55283adee1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71230
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Due to a high I2C bus load on the mainboard I2C frequency of 400 kHz
leads to poor signaling. Therefore limit the I2C speed to 100 kHz for
this bus. In addition, add a generic I2C device with 100 kHz bus speed
to the devicetree so that the OS will not switch to higher clock rates,
too.
Test= Measure the I2C signals at coreboot and OS runtime and ensure the
clock is always at 100 kHz.
Change-Id: I6b0a642cd3f5b77331663ac8c76ed0a116ae77ca
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71227
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove the PSE TSN GbE device #0 as it's unused on the board and not
visible during the PCI enumeration.
Change-Id: I4a7d0e437c4f4a12d3a07564cddeafb7c697c6d3
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70700
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Contrary to mc_ehl2, which this variant is based on, this board
doesn't contain the TI XIO2001 PCIe-to-PCI bridge, which makes the
attempts to modify the bridge's registers unnecessary.
Change-Id: I6597ceb78e4c790c08a0dfa9535dece33a8f95b8
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70854
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based upon hardware differences from mc_ehl2, disable RP7
and enable RP3 and RP5.
Change-Id: Iecaa3098c3e4c9ce15254bb8bd1fe6da86d6e706
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70689
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a new mc_ehl variant, which is based on mc_ehl2 implementation.
This patch uses a copy of mc_ehl2 with changes only in naming
as a starting point for the new mc_ehl3 variant.
Follow-up patches will introduce the functional changes against
mc_ehl3.
Change-Id: Ie8c18b4f16d88b175ce576c2ef4c2e6ee0b4c306
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70688
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
<device/mmio.h>` chain-include `<arch/mmio.h>:
https://doc.coreboot.org/contributing/coding_style.html#headers-and-includes
Also sort includes while on it.
Change-Id: Ie62e4295ce735a6ca74fbe2499b41aab2e76d506
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Found using 'Wmissing-include-dirs' command option.
Change-Id: Ie9ff43432215ebc89e6c1ea5f86b248e7fecd943
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70396
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GSPI2 interface is not used on this mainboard and can be disabled. It
will in addition remove the warning of a leftover static device in the
log.
Change-Id: I6e7462312953d50385ca7bb2f2e0abb8fc3a5886
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
As for mainboard mc_ehl1, a hard real-time dependency is also required
for this mainboard. The L1 prefetcher on Elkhart Lake is too aggressive
which in the end leads to an increased number of cache misses. Disabling
the L1 prefetcher boosts up the performance (in some cases by more than
10 %) in this specific use case.
Change-Id: I07b27dd672533e693a6c2987d16f54333850760e
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Set downshift counter to 2 for all Marvell PHYs on this mainboard before
the PHY downshifts to the next highest speed.
Change-Id: I32b5f25a3e1e0f962dff3110143e236992ef8e7d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69887
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On this mainboard Marvell PHY INTn is routed to LED[2] pin.
Change-Id: I28a78afdcf0599bb998f906ce8056a0586e24f33
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69434
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mainboard has three Marvel PHYs connected to the internal SOC GbE
controllers. The default LED status after HW reset of this PHYs shows a
different mode than what is needed. LED[2] is not connected on this
mainboard.
This patch sets the following LED status:
LED[0] - 7 = On - 1000 Mbps Link, Off - Else
LED[1] - 1 = On - Link, Blink - Activity, Off - No Link
LED[2] - not connected
TEST=Try different register values to verify LED feature.
Change-Id: I51d817bc720bf787279777f503efdc17dbb1274d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69387
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
device
Instead of creating a dummy I2C device in order to force Linux to
decrease the I2C bus speed, use the own 'bus_speed' field of RV3028
device config structure.
Linux should always set the bus speed to the speed of the slowest
device sitting on the bus. Hence the dummy device is not needed
here anymore.
BUG=none
TEST=See if the RV3028 RTC is visible and working (date/time can
be set/read) in Linux. At the time, a driver modification is needed
to add a match table for the "MCRY3028" ACPI HID. A proper kernel
patch is pending.
Change-Id: I6e269dc67d1fe2a6747fcf3bee224def7b553f08
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69544
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Provide timing parameter for SSDT generation to achieve the requested
100 kHz speed with a high accuracy.
Test: Measure I2C bus clock, high and low times during I2C access from
Linux and confirm they match the specification.
Change-Id: Ifb6019421b612133b8f25c076519bc0e7200dad8
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
In Linux, the I2C speed defaults to 400 kHz if there is no device
registered in ACPI which requests a different speed. Due to board
limitations (layout, bus load), 400 kHz are too fast which results in a
timing violation. Therefore, add a dummy I2C device to both used I2C
buses (I2C1 and I2C2) with a speed of 100 kHz. This will limit the bus
speed in Linux accordingly.
Change-Id: I507c53c9ec7f763cef18903609231b1a66ed98fa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The SPD data for DRAM init has moved into the hwinfo data structure and
is therefore not used from spd.bin anymore. spd.bin will not receive any
updates, changes will only be done in hwinfo. There is no reason to keep
spd.bin around so remove it for both variants.
Change-Id: Ie6091b655ba7ff2e01b684266ce34b85593b8623
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Enable early POST code output for this mainboard, using
the NC FPGA device on PCIe.
This requires the parent PCI bridge to be initialized early.
BUG=none
TEST=boot on siemens/mc_apl2 and observe whether the POST
codes coming from before FSP-M init are visible
Change-Id: Ice5fe26e11d0513e6bb0a20f1d8f0483d7b3dc6a
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The highly real time driven application executed on mc_ehl1 has shown
that the L1 prefetcher on Elkhart Lake is too aggressive which in the
end leads to an increased number of cache misses. Disabling the L1
prefetcher boosts up the performance (in some cases by more than 10 %)
in this specific use case.
Change-Id: Id09a7f8f812707cd05bd5e3b530e5c3ad8067b16
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68668
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Add a config for FIVR in devicetree for both, mc_ehl1 and mc_ehl2
variants in order to provide the real delay value for the VCC supply
rail. This delay is needed to enable proper switching between different
VCC levels based on current system state.
Change-Id: Ibccb8ea1b42ccd2ff0a37cbd9651528a2a55ebd6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Apollo Lake seems to start with PCIe root ports unusable/uninitialized
before FspMemoryInit() is called and FSP-M properly initializes these
root ports.
However, we need the root ports accessible before FspMemoryInit() in
certain cases, such as emitting POST codes through a PCIe device.
For the initialization to happen properly, certain register writes
specified in Apollo Lake IAFW BIOS spec, vol. 2 (#559811), chapter
3.3.1 have to be done.
BUG=none
TEST=Boot on siemens/mc_apl2 with NC_FPGA_POST_CODE enabled and check
that the POST codes are emitted before FspMemoryInit().
Change-Id: If782bfdd5f499dd47c085a0a16b4b15832bc040e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68223
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The intention of predefining driver strength is to avoid that the OS
SD-Card driver changes this setting.
Change-Id: I02fdac94462da1cd77f8dc972faf16f28d94c946
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
