summaryrefslogtreecommitdiff
path: root/src/mainboard/siemens
AgeCommit message (Collapse)Author
2017-09-08siemens/mc_apl1: Disable internal UARTsMario Scheithauer
APL internal UARTs are not used on this mainboard. Change-Id: I39118262fc6f37b45785538a3f2d1d31d42cbe86 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/21406 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-09-08siemens/mc_apl1: Set bus master bit for on-board PCI deviceMario Scheithauer
There is one on-board PCI device where bus master has to be enabled in PCI configuration space. As there is no need for a complete PCI driver for this device just set the bus master bit in mainboard_final(). Change-Id: I45202937eba11da3bea14fef6ebed70599804335 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/21405 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-08-23AMD fam10 ACPI: Use common fixed sleepstates.aslKyösti Mälkki
SSFG was meant to be used as a mask to enable sleepstates _S1 thru _S4. However as a logical instead of bitwise 'and' operation was used, all the states were enabled if only one was marked available. Note that all boards incorrectly had SSFG == 0x0D that previously enabled ACPI S3 sleep state even when it was not available. Change-Id: Ia948becff079383cbf861468da9e8a3ebbf213cb Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/21093 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
2017-08-22AMD K8 fam10-15: Consolidate post_cache_as_ram callKyösti Mälkki
Change-Id: I5e7890aafbc8c80716ee49690e306482a482a863 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/20573 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
2017-08-18drivers/i2c/rx6110sa: Drop I2C interface arbitrationNico Huber
Change-Id: Ib31e77eec639c231520198c0b978d6c3c1eadaed Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/20454 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-08-18include/device: Split i2c.h into threeNico Huber
Split `i2c.h` into three pieces to ease reuse of the generic defi- nitions. No code is changed. * `i2c.h` - keeps the generic definitions * `i2c_simple.h` - holds the current, limited to one controller driver per board, devicetree independent I2C interface * `i2c_bus.h` - will become the devicetree compatible interface for native I2C (e.g. non-SMBus) controllers Change-Id: I382d45c70f9314588663e1284f264f877469c74d Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/20845 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-08-15soc/intel/common/block: Add LPC Common code and use it for APLRavi Sarawadi
Add LPC common code to be shared across Intel platforms. Also add LPC library functions to be shared across platforms. Use common LPC code for Apollo Lake soc. Update existing Apollolake mainboard variants {google,intel,siemens} to use new common LPC header file. Change-Id: I6ac2e9c195b9ecda97415890cc615f4efb04a27a Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com> Reviewed-on: https://review.coreboot.org/20659 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-07-27siemens/mc_apl1: Select skip RAPL configurationMario Scheithauer
The mc_apl1 mainboard needs to disable the RAPL algorithm for a constant power management of the processor package. An active RAPL algorithm leads to negative effects with our real time software. Change-Id: I09ca56a034fd3896a000e64cac35f12fb507a682 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20760 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-07-20siemens/mc_apl1: Activate ECC for DRAMMario Scheithauer
This mainboard is equipped with DDR3L modules which support ECC. The BWG says that for activating ECC the FSP-M parameter MemoryDown must be set to 5. Change-Id: Idc68df1e2bae2396c9b9788d4a026a75b7d9119b Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20634 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-07-20siemens/mc_apl1: Include platform.aslMario Scheithauer
The OS of this mainboard needs the _PIC method for the selection of the type of interrupt routing. Change-Id: Ic82ba1b368aff0030422d9602ebc882247a2191b Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20618 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-07-18siemens/mc_apl1: Disable SDCARDMario Scheithauer
SDCARD is not used on this mainboard. Change-Id: I28d23cdb3652bf736b19daf67c7057c396230e24 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20611 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-07-14K8: Fix indirect includesKyösti Mälkki
Change-Id: I370285aa52776170a32b6dd36c0eef74eea9400c Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/20562 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-07-13Rename __attribute__((packed)) --> __packedStefan Reinauer
Also unify __attribute__ ((..)) to __attribute__((..)) and handle ((__packed__)) like ((packed)) Change-Id: Ie60a51c3fa92b5009724a5b7c2932e361bf3490c Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-on: https://review.coreboot.org/15921 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-07-06mainboard/[m-w]: add IS_ENABLED() around Kconfig symbol referencesMartin Roth
Change-Id: Ifba3257b0328d0b6ad1bee9bf885683998df5851 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/20344 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2017-06-30mb/siemens/mc_apl1: Set up RTC backup mode to primary cellWerner Zeh
Set RX6110SA RTC backup mode to primary cell. This mode reduces the backup current consumption of the RTC. Change-Id: I7c0c26a0ed5d8f48587acc917f8bb1c5c2b8869a Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/20414 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2017-06-30mb/siemens/mc_bdx1: Set up RTC backup mode to primary cellWerner Zeh
The used RTC6110SA has issues to enter backup mode when the power supply decreases too slow when the mainboard is turned off. Switch to backup mode "primary cell" to make sure backup mode will be entered correctly on power-off. In addition set IOCUTEN to minimize the backup current consumption of the RTC. Change-Id: I9733aa9f2981a25f6d42279eff0c4980e5eb5a5a Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/20413 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2017-06-29mb/siemens/mc_bdx1: Set bus master bit for on-board PCI devicesWerner Zeh
There are up to two on-board PCI devices where bus master has to be enabled in PCI config space. As there is no need for a complete PCI driver for these devices just set the bus master bit in mainboard_final(). In a perfect world that would be the task of the runtime driver which unfortunately don't do that. Change-Id: Ic2896d5e7568a455737af26b14b2c398caae5f72 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/20403 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-06-23siemens/mc_apl1: Enable decoding for COM 3 on LPCMario Scheithauer
It does not work to enable the LPC range in the function mainboard_init() because the LPC bus driver closes the range during PCI enumeration again. For this reason, enabling decoding of the address range for COM 3 will be done at a later point in time - mainboard_final(). Change-Id: I452bca4e430b1ea75e4a327591da84500491fe84 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20295 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-06-23siemens/mc_apl1: Disable XDCIMario Scheithauer
With enabled XDCI support we are not able to use USB port 0 over XHCI driver. For this reason, we disable XDCI into devicetree.cb. Change-Id: I1ed721d9ffd44a920a6f1f16855d5b7ceb1b17c5 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20296 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-06-13siemens/mc_apl1: Enable decoding for COM 3 on LPCMario Scheithauer
Since this mainboard provides 3 COM ports on LPC, enable decoding of the corresponding address range for COM 3. Change-Id: I15c0748fce67eef46401c314f441aa45f5e3c5fa Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20162 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-06-13siemens/mc_apl1: Use Siemens NC FPGA driverMario Scheithauer
- use Siemens NC FPGA driver for backlight brightness and PWM control - set Dsave time for board reset after falling edge of signal xdsave Change-Id: I5077d4af162e54a3993e5e0d784a8356f51bd0c9 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20161 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-05-31mc_tcu3: Remove all hwinfo files from mainboard directoryWerner Zeh
To unify the hwinfo handling along all Siemens MC boards the hwinfo files have to be removed from the mainboard directory. They will be added to cbfs in site-local/Makefile.inc. Change-Id: Ia3dcb2e0118527b37aed872740273c4fa7004aef Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/19982 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2017-05-31mc_bdx1: Switch to RTC RX6110SAWerner Zeh
The prior used RTC PCF8523 is replaced with RX6110SA on this mainboard. Switch to the new RTC in Kconfig and adapt devicetree to the new chip. Change-Id: I7c4911191cae254900f9a958da42ecd18497484c Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/19979 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2017-05-17siemens/mc_apl1: Program eMMC DLL settingsMario Scheithauer
Program eMMC DLL settings for mc_apl1 mainboard, after that system can boot up with eMMC successfully. Change-Id: I3d60f66ec5c7e09540ccda59f244aac6f78bf954 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/19712 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-05-17siemens/mc_apl1: Select external 8250 UARTMario Scheithauer
The mainboard siemens/mc_apl1 uses an external I/O port for console output. For this reason we need to activate the 8250 LPC UART. Change-Id: Ib5616a116aec6135191bdce95f9f9566ce13d6f1 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/19694 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-05-11siemens/mc_apl1: Add usage of external RTC RX6110 SAMario Scheithauer
This mainboard contains an external RTC chip RX6110 SA. Enable usage of this chip and set some initialization values to device tree. Change-Id: I5aceb4401f0bb059ef893dfe7d157716c82e4a76 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/19647 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-05-11siemens/mc_apl1: Correct GPIO settingsMario Scheithauer
- set GPIO_183 to high level for enabling the power of SD card - delete all GPIOs for JTAG interface because they lead to problems with Lauterbach debug hardware Change-Id: I24bfff479601933c43e3dcbfa3baa49510831703 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/19623 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-05-05mainboard/siemens/mc_apl1: remove unnecessary headerAaron Durbin
soc/i2c.h does not need to be included in this compilation unit. Change-Id: Ife11642d2e69af7235c93fc54bba38853b046169 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/19572 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-04-28nb/amdk8: Link coherent_ht.cArthur Heymans
Change-Id: I1ef1323dc1f3005ed194ad82b75c87ef41864217 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/19367 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2017-04-28nb/amd/amdk8: Link reset_test.cArthur Heymans
This needs some extra headers in amdk8/raminit.c that were otherwise provided by that file. Change-Id: I80450e5eb32eb502b3d777c56790db90491fc995 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/19360 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2017-04-27nb/amd/amdk8: Link raminit_f.cArthur Heymans
For this debug.c needs to be linked too. Change-Id: I9cd1ffff2c39021693fe1d5d3f90ec5f70891f57 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/19030 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2017-04-10nb/amdk8/(pre_)f.h: Don't declare global variable in headerArthur Heymans
This is needed if one wants to use the header more than once. Change-Id: I375d08465b6c64cd91e7563e3917764507d779ba Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/19029 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2017-04-04siemens/mc_apl1: Activate PTN3460 eDP to LVDS bridge ICMario Scheithauer
This mainboard uses a LVDS connection for LCD panels. Apollo Lake SoC provides a display controller with three independent pipes (1x eDP and 2x DP/HDMI). PTN3460 is an embedded DisplayPort to LVDS bridge device that enables connectivity between an eDP source and LVDS display panel (http://www.nxp.com/documents/data_sheet/PTN3460.pdf). The bridge contains an On-chip Extended Display Identification Data (EDIT) emulation for EDIT data structures. This patch sets up PTN3460 to be used with the appropriate LCD panel. Change-Id: Ib8fa79bb608f1842f26c1af3d7bf4bb0513fa94d Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/19043 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-29siemens/mc_apl1: Adjust gpio settingsMario Scheithauer
Adjust gpio settings according to the hardware layout. Change-Id: I2f440e863c2e6f59298c500ac5aefa3b7386bcdf Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/18995 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-03-21mainboards: Don’t select `CONSOLE_POST`Paul Menzel
Currently, it’s impossible for the user to select `NO_POST`, for boards selecting `CONSOLE_POST` in their config. ``` warning: (BOARD_SPECIFIC_OPTIONS) selects CONSOLE_POST which has unmet direct dependencies (VENDOR_SIEMENS && BOARD_SIEMENS_MC_BDX1 || !NO_POST) ``` This is currently done for Intel Camelback Mountain and Siemens MC-BDX1. Selecting the option `CONSOLE_POST` in board specific configuration is not a good idea, as this should be user configurable over Kconfig, and also the tree-wide defaults should be the same for these options. Kconfig is different, as commit 97535558f1 (mainboard/{google,intel}: Change config option selection) only touch the Intel board. Change-Id: I91c1e0cb92ed218b6bbc7c33759b91f748cf6f51 Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-on: https://review.coreboot.org/18878 Tested-by: build bot (Jenkins) Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-03-15siemens/mc_apl1: Clean up the codeMario Scheithauer
This patch make some general adaptations in relation to commit 6a489237 (mainboard/intel/leafhill: Clean up). - add necessary defaults to Kconfig - remove irrelevant entries from FMD file - include romstage file for better understanding Change-Id: I190d648a7ffeca11acc6560db85ff03c78e85b21 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/18808 Tested-by: build bot (Jenkins) Reviewed-by: Andrey Petrov <andrey.petrov@intel.com> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-20siemens/mc_apl1: Set MAC address for all available i210 MACsMario Scheithauer
This mainboard uses two i210 Ethernet controller. Therfore we enable the usage of the i210 driver and have to provide a function to search for a valid MAC address for all i210 devices by using Siemens hwilib. Change-Id: I36246cdef987fcece15a297ebb2f41561fca1f69 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/18380 Tested-by: build bot (Jenkins) Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-02-15siemens/mc_apl1: Make basic settings for booting the mainboardMario Scheithauer
This commit makes a basic adjustment for GPIOs, device tree, flash map and MRC settings. With these basic settings the mainboard boots into Linux lubuntu 4.8.0-22-generic using SeaBIOS. More adjustments will follow. Change-Id: Ia920d236814f2e6a9b777dd1e4b4feef0ddf7721 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/18292 Tested-by: build bot (Jenkins) Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-02-02siemens/mc_apl1: Add new mainboardMario Scheithauer
This mainboard is based on Intel's Leafhill CRB with Apollo Lake silicon. In a first step, it concerns only a copy of intel/leafhill directory with minimum changes. Special adaptations for MC APL1 mainboard will follow in separate commits. Change-Id: If0b8a2bc21c99c3be4e6043e8febfb1b91ff0a63 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/18272 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Brenton Dong <brenton.m.dong@intel.com>
2017-01-13fsp_baytrail: Enable graphic init per defaultWerner Zeh
Baytrail SoC has a bug where in some cases the DisplayPort can hang leading to a non-working display (it just stays black). To avoid this hang, a patch was introduced in 02/2016 (1c3b1112fa - fsp_baytrail: Fix a possible hanging DisplayPort) but per default not switched on so that each mainboard can decide if it wants to use this patch or not. Recently a new case of this bug was reported by Benoit Sansoni (benoit.sansoni@kontron.com) and he requested to enable this fix per default as it costs him a lot of time to find the cause and even the already available fix in coreboot. To avoid this effort for someone else in the future we can enable this fix per default as no negative side effects are known and it is now tested at Siemens and at Kontron on different mainboards with success. As the goal is to enable this code permanently the config switch is not longer needed and is removed. Change-Id: I15bd682218d0dc887945cc91ee3e5488945a6355 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/18109 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.h@gmx.de>
2016-12-26amd-based mainboards: Fix whitespace in _PTS commentsMarshall Dawson
Correct tabs that were intended as spaces. Change-Id: Idcf33d829f87a866b5ed880527102918d5b93842 Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com> Reviewed-on: https://review.coreboot.org/17905 Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins)
2016-12-06cpu/amd/mtrr.h: Drop excessive includesKyösti Mälkki
Change-Id: Id404bdab1f2361f1e7d20f7ee72111971863dddf Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/17736 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-12-06cpu/x86/msr.h: Drop excessive includesKyösti Mälkki
Change-Id: Ic22beaa47476d8c600e4081fc5ad7bc171e0f903 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/17735 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-12-06cpu/cpu.h: Drop excessive includesKyösti Mälkki
Change-Id: Ifeef04b68760522ce7f230a51f5df354e6da6607 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/17734 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-12-06CPU: Move SMM prototypes under x86Kyösti Mälkki
Change-Id: Iefbc17dcfcf312338d94b2c2945c7fac3b23bff6 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/17732 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2016-12-06mc_tcu3: Do not abort initialization of PTN3460 when HW-ID is missingWerner Zeh
Do not abort the initialization of PTN3460 if HW-ID could not be retrieved and just assume that the HW-ID does not match 7.9.2.0. In this case PTN3460 will be setup to a working condition even if this field is missing. This makes this driver more robust with faulty blocks. Change-Id: I301fb165a7924768e44182d92be820294beb0280 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/17671 Tested-by: build bot (Jenkins) Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2016-11-24mc_tcu3: Swap LVDS even and odd lanes for a certain hardwareWerner Zeh
Due to some LVDS cable constraints even and odd lanes needs to be swapped on certain hardware. The hardware ID will be used to distinguish between these two cases. The swapping itself will be done by PTN3460, which is configurable for that. Change-Id: I339b2321a8ed1bc3bbf10aa8e50eb598b14b15fa Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/17576 Tested-by: build bot (Jenkins) Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2016-11-21mb/siemens/sitemp_g1p1/cmos.layout: Re-add cmos_defaults_loadedNico Huber
I guess it was dropped because its concept was misunderstood. The idea is to always have it set to `Yes` in the cmos.default. Users can then ack the loading of the defaults by setting it to `No`. If the defaults ever get loaded again, they'll be notified by the default `Yes`. Change-Id: I1aa6d75bd5aa153c7b11a6b74564272eaa7cc523 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/17355 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-05siemens/mc_tcu3: Increase LCD backlight turn-on delay to 500 msWerner Zeh
Due to different LCD panel requirements the delay between LVDS becomes active and the backlight is switched on needs to be increased to 500 ms. Change-Id: I09029624469aef412141c7b46224d48557ba4af1 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/16875 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-10-04mainboard/siemens/sitemp_g1p1: Use tabs for indentsElyes HAOUAS
Change-Id: Ia5ea2198cdc93822723a4fe5440d574d76cb4de2 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16847 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01mainboard/*/*/*/usb.asl: Use tabs for indentsElyes HAOUAS
Change-Id: Id46a0c4ca59dc7224c2eedd674ea3a5486509de1 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16824 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-09-26mainboard/*/*/dsdt.asl: Use tabs for indentsElyes HAOUAS
Change-Id: Idef587d8261784e916e8d50f4336cbcfca39b9b0 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16730 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2016-09-26mainboard/*/*/mptable.c: Improve code formattingElyes HAOUAS
Change-Id: I341293cd334d6d465636db7e81400230d61bc693 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16723 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2016-09-20src/mainboard/lenovo-winent: Add space around operatorsElyes HAOUAS
Change-Id: Iab2a879ebdea9d93ef5eb7e3abf875036c1e1cb4 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16641 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2016-09-12siemens/mc_bdx1: Enable decoding for COM 3 & COM 4 on LPCWerner Zeh
Since this mainboard provides 4 COM ports on LPC, enable decoding of the corresponding addresses using the generic LPC decode registers. Change-Id: I0e93d40dca01d55f3567a18c7ec02269e3bec466 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/16535 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-08-17mainboard: Clean up boot_option/reboot_bits in cmos.layoutNico Huber
Since commit 3bfd7cc (drivers/pc80: Rework normal / fallback selector code) the reboot counter stored in `reboot_bits` isn't reset on a reboot with `boot_option = 1` any more. Hence, with SKIP_MAX_REBOOT_CNT_CLEAR enabled, later stages (e.g. payload, OS) have to clear the counter too, when they want to switch to normal boot. So change the bits to (h)ex instead of (r)eserved. To clarify their meaning, rename `reboot_bits` to `reboot_counter`. Also remove all occurences of the obsolete `last_boot` bit that have sneaked in again since 24391321 (mainboard: Remove last_boot NVRAM option). Change-Id: Ib3fc38115ce951b75374e0d1347798b23db7243c Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/16157 Tested-by: build bot (Jenkins) Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com> Reviewed-by: York Yang <york.yang@intel.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-08-14src/mainboard: Capitalize ROM, RAM, CPU and APICElyes HAOUAS
Change-Id: Ia1f24d328a065a54975adde067df36c5751bff2d Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/15987 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-08-01Remove non-ascii & unprintable charactersMartin Roth
These non-ascii & unprintable characters aren't needed. Change-Id: I129f729f66d6a692de729d76971f7deb7a19c254 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/15977 Tested-by: build bot (Jenkins) Reviewed-by: Omar Pakker Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2016-08-01Add newlines at the end of all coreboot filesMartin Roth
Change-Id: I7930d5cded290f2605d0c92a9c465a3f0c1291a2 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/15974 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-08-01siemens/sitemp_g1p1: Fix typoPatrick Georgi
Change-Id: I1c9af223d3598c4822905acce0cf9b1dca6ad1b6 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Found-by: Coverity Scan #1287066 Reviewed-on: https://review.coreboot.org/15981 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2016-07-31mainboard: Format irq_tables.cPaul Menzel
Run the command below to format the files `irq_tables.c` of (mostly AMD) mainboards correctly with GNU indent 2.2.10. ``` $ git grep -l 'if (sum != pirq->checksum) {' | xargs indent -l ``` Fix up the following two checkpatch.pl errors manually. ``` ERROR: that open brace { should be on the previous line #1219: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:129: + uint8_t reg[8] = + { 0x41, 0x42, 0x43, 0x44, 0x60, 0x61, 0x62, 0x63 }; ERROR: that open brace { should be on the previous line #1221: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:131: + uint8_t irq[8] = + { 0x0A, 0X0B, 0X0, 0X0a, 0X0B, 0X05, 0X0, 0X07 }; ``` This is needed, so that follow-up commits, fixing checkpatch.pl errors and warnings, won’t run into conflicts with the git commit hooks, when for example, spaces instead of tabs are used for indentation. Change-Id: If254723f3013377fb3b9b08dd5eca6b76730ec4a Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-on: https://review.coreboot.org/15932 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2016-07-31Update degree symbol to utf-8 encoding in commentsMartin Roth
Almost all of the places where we have the degree symbol '°', it's encoded as 0xc2 0xb0 (utf-8 encoding). There are a few places where it is encoded as just a high ascii byte: 0xb0. Editors that support the high ascii 0xb0 seem to support the utf-8 0xc2 0xb0 encoding as well, but the opposite does not seem to be true. Change the high-ascii degree symbols to utf-8 encoding. Change-Id: I3d06289b802f45e938dc72b4c437fca56235b62b Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/15978 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Alexander Couzens <lynxis@fe80.eu> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-07-14siemens/mc_bdx1: Add usage of external RTC PCF8523Werner Zeh
This mainboard contains an external RTC chip PCF8523. Enable usage of this chip and add some initialization values to device tree. Change-Id: I25c0a017899ee904f3aa02bdc7dcaf61dee67e3a Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/15642 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-07-08siemens/mc_bdx1: Move SCI to IRQ 10Werner Zeh
IRQ 9 is used for different purpose on this board so move SCI away to IRQ10. Change-Id: I107bfb5ec8cd05f844ee75550779be7746e77a88 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/15563 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-07-07siemens/mc_bdx1: Set up opcode menu for SPI controllerWerner Zeh
Since SPI controller opcode registers are locked by FSP, they need to be initialized to a known good state before ReadyToBoot event and after every SPI flash access (e.g. for MRC cache) has been finished in order to enable the OS to use SPI controller without constraints. Change-Id: I0a66344cd44e036c3999ae98d539072299cf5112 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/15547 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2016-07-06siemens/mc_bdx1: Add usage of Siemens NC FPGA driverWerner Zeh
Enable NC FPGA driver for this mainboard. Change-Id: I87b6b10038f3d161a25b2008b7ea44b5627cca43 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/15545 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-07-05siemens/mc_bdx1: Set up MAC address for available i210 MACsWerner Zeh
Enable the usage of DRIVER_INTEL_I210 and provide a function to search for a valid MAC address for all i210 devices using hwilib. Change-Id: Ic0f4f1579364cf5b0111334a05a8a0926785318b Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/15517 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-07-05intel/i210: Change API for function mainboard_get_mac_address()Werner Zeh
The function mainboard_get_mac_address() is used to get a MAC address for a given i210 PCI device. Instead of passing pure numbers for PCI bus, device and function pass the device pointer to this function. In this way the function can retrieve the needed values itself as well as have the pointer to the device tree so that PCI path can be evaluated there. Change-Id: I2335d995651baa5e23a0448f5f32310dcd394f9b Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/15516 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-05-10siemens/mc_tcu3: Don't try to init unsupported panel typeWerner Zeh
The LCD panel type is read using 4 GPIOs. Of these 16 possible combinations only 5 are supported right now. If the GPIO setting encodes an unsupported panel type, there will be no matching hwinfo.hex in cbfs. Therefore it makes no sense to try to initialize the DisplayPort-2-LVDS converter. Leave the function instead in this case. Change-Id: If8c67a3f5be762758d516c4939dd1de4ff1c8ba5 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/14743 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2016-05-09siemens/mc_tcu3: Fix spelling of *set up*Paul Menzel
The verb *set up* is written with a space [1]. So correct that in the function descriptions. [1] http://www.merriam-webster.com/dictionary/set%20up Change-Id: Icf5aa7eca2c379fdf7ff1935d71efc347f5ce6fa Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: https://review.coreboot.org/14701 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2016-05-09siemens/mc_tcu3: Add blank lines for better legibilityPaul Menzel
Change-Id: I6d1200dd59e53ca892594c1fce784639a9817550 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: https://review.coreboot.org/14700 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2016-05-09siemens/mc_tcu3: Remove unneeded variable assignmentPaul Menzel
Assigning the value `1` to `status` in the default branch of the switch statement is not needed, as the stored value is overwritten before it can be used. Change-Id: I532b0e217ff4ed315cd30b08d339c755c6df7539 Found-by: Coverity, CID 1355008: Code maintainability issues (UNUSED_VALUE)) Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: https://review.coreboot.org/14699 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2016-04-29siemens/mc_bdx1: Add new mainboard.Werner Zeh
Add new mainboard for MC BDX1 board which is based on Intel Camelback Mountain. This mainboard is an industry type board and has several Ethernet interfaces among with two USB3.0 connectors. It uses 24V DC power supply and has its own form factor which does not match any standard. This commit adds the new mainboard and prepares the Kconfig environment so that this board can be selected and generated. Although the generated image can boot into Linux and DOS, not all functions are implemented yet. Forthcoming commits will add more functionality. Change-Id: I29011cfd3b0d13bcf163223f657e02f69978e39a Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/14516 Tested-by: build bot (Jenkins) Reviewed-by: York Yang <york.yang@intel.com>
2016-04-28drivers/intel/i210: Use uint8_t and friends instead of u8Werner Zeh
Switch all types to uint8_t and the like instead of u8. Change-Id: Ia12c4ee9e21e2d3166c2f895c819357fa2ed9a94 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/14515 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-04-28mc_tcu3: Switch to hwilib instead of own hwinfo implementationWerner Zeh
Use hwilib in vendorcode/siemens/hwilib to get fields from hwinfo instead of having mainboard specific hwinfo code. This patch does not change the functional behavior in any way. Change-Id: Idb226a82a08b1b753f654c5cde106236e72f33c3 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/14506 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-02-25mc_tcu3: Enable graphic init codeWerner Zeh
The used Baytrail-M SoC on TCU3 tend to have issues with DisplayPort if the graphic power gate is not set up in coreboot. To avoid this error, use the graphic init code on this board. Change-Id: I973bbaa7d86c1ede1f2884b3a08ccb31f7d85087 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/13774 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-02-02src/: Fix Kcofig symbols missing CONFIG_ prefixMartin Roth
- Add CONFIG_ prefix to two symbols. - Remove the use of the third symbol as it will never be matched. Change-Id: Ifa7f6884001cb05fb8397f193c4b08a0161f498c Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/13539 Tested-by: build bot (Jenkins) Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2016-01-25mc_tcu3: Enable auto generated attributes in cbfsWerner Zeh
Use CBFS_AUTOGEN_ATTRIBUTES for mc_tcu3 to enable position and alignment attributes in cbfs. Change-Id: I6c39bb02ab641d7e22e20e77a72a577f159549dd Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/13123 Tested-by: build bot (Jenkins) Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2015-12-18siemens/mc_tcu3: Set GPIO_S0_SC[75] to outputWerner Zeh
The usage of the pin has changed and therefore this pin needs to be set up as output and drive low initially. Change-Id: Ie3eb9cc703f7f73d59fad52ea9e514997d84606a Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/12754 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2015-12-16intel/fsp_baytrail: rename include folder baytrail to include/socBen Gardner
This is to match the layout of the non-fsp baytrail to make comparisons easier and possibly remove duplicate files. Change-Id: I9a94842d724ab3826de711d398227e7bdc1045ff Signed-off-by: Ben Gardner <gardner.ben@gmail.com> Reviewed-on: https://review.coreboot.org/12686 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2015-12-16southbridge/amd/sb600: Update HPET base address with #defineMartin Roth
The SB600 code had the base address of the HPET hardcoded throughout. It looks like the plan was to have it be updated in ACPI if needed, but this wasn't ever implemented. The variable names being used to do this update were the same, causing an IASL warning. Because of this, the operation to update the HPET address actually did nothing. This was fine, because it didn't actually need to be updated. - Replace all that code with a #define. - Add and update some comments in the same area. Fixes IASL warning: dsdt.aml 1505: Store(HPBA, HPBA) Warning 3023 - ^ Duplicate value in list (Source is the same as Target) Change-Id: I9ba5fe226a4a464e0045ce7d3406898760df5e5a Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/12705 Tested-by: build bot (Jenkins) Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
2015-12-10ACPI: Work around IASL warning reading/writing same registerMartin Roth
The newer versions of IASL are unhappy when an operator has the same object as both source and destination. The warning can be completely disabled with a command line argument, but in general, I'd really rather not just disable warnings. The bits in this register are write 1 to clear, so reading and writing the same register is what we want to do. Instead, store it in a temporary register then write it in a second operation. Fixes warning: dsdt.aml 1396: Store(PWST, PWST) Warning 3023 - ^ Duplicate value in list (Source is the same as Target) Change-Id: I52d73d4431db237be83016d67cd397f31b53d9c6 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/12691 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2015-12-10ACPI: Fix IASL Warning about unused method for _OSI checkMartin Roth
According to the ACPI Spec for CondRefOf, the result argument is optional. In all of these locations, it was getting set but not used, creating a warning in new versions of IASL. Since it's an optional argument, just remove it. dsdt.aml 22: if(CondRefOf(\_OSI,Local1)) Warning 3144 - ^ Method Local is set but never used (Local1) Change-Id: I07f49ac5a3708838d1c4a7216dfb11acc415c881 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/12692 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2015-12-06fsp_baytrail: Change A, A, A, A IRQ routing to A, A, A, BMartin Roth
Devices that have their interrupt routing set to A, A, A, A don't get any interrupt values assigned because that series evaluates to 0. The code that sets the interrupt values checks to make sure a value is set by verifying that it's not 0. On Bay Trail, these are all single-function graphics devices, so by changing one of the unused interrupt lines from A to any other value, it assigns the values correctly. This issue did not affect ACPI interrupt routing. This is just a workaround, and the root issue still needs to be fixed. Change-Id: I78866e3e0079435037e457a4fb04979254b56ee2 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/12629 Tested-by: build bot (Jenkins) Reviewed-by: Ben Gardner <gardner.ben@gmail.com> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2015-11-20siemens/mc_tcu3: Clear checksums in hwinfoWerner Zeh
Clear the precomputed checksums in hwinfo as they will be updated in manufacturing process. Change-Id: I952ca8f1ca32831c4b296de633c0d58da111ccba Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: http://review.coreboot.org/12475 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2015-11-10mainboard/**/irq_tables.c: Remove reference to getpirPatrick Georgi
The obsolete and removed getpir utility remarked in its output that the data is autogenerated. The tool was removed because it wasn't very reliable, so there's no need to point that anymore. Change-Id: I5d624931ba7872b1fefa8fa3c270ae7367e069fa Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Reviewed-on: http://review.coreboot.org/12354 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2015-11-05mainboard: Remove last_boot NVRAM optionTimothy Pearson
The last_boot NVRAM option was deprecated and removed in commit 3bfd7cc6. Remove the last_boot option from all affected mainboards to eliminate user confusion. Change-Id: I7e201b9cf21dfe5dda156785bad078524098626d Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com> Reviewed-on: http://review.coreboot.org/12316 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins)
2015-10-31tree: drop last paragraph of GPL copyright headerPatrick Georgi
It encourages users from writing to the FSF without giving an address. Linux also prefers to drop that and their checkpatch.pl (that we imported) looks out for that. This is the result of util/scripts/no-fsf-addresses.sh with no further editing. Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Reviewed-on: http://review.coreboot.org/11888 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2015-10-29mainboard: Convert #ifdef to IS_ENABLED in get_bus_conf.cTimothy Pearson
Change-Id: I254e9e9e65519edcf4d3f1ecc385af16d18c2367 Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com> Reviewed-on: http://review.coreboot.org/12208 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2015-10-24amd/acpi: Clean up SMBus references.Tobias Diedrich
Replace the AMD SMBus section with the equivalent SB800 smbus.asl include or remove already commented-out sections. Verified by running the cpp preprocessor over the DSDTs and diffing the results against this patch. The only change is in src/mainboard/siemens/sitemp_g1p1/dsdt.asl, where someone added RADD and SADD to the OpRegion, but those are unused, so removing them is fine. Change-Id: I074c8a1ed1c9a944d4988752bd0fc42c199c766c Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de> Reviewed-on: http://review.coreboot.org/10618 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2015-10-02mc_tcu3: Remove dummy blocks from hwinfo.hexWerner Zeh
Remove dummy data from hwinfo.hex as it is not needed anymore in the system. Change-Id: I4f328a4ef61741039eb2c030e23fea33f539c2bb Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: http://review.coreboot.org/11763 Tested-by: build bot (Jenkins) Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2015-10-02mc_tcu3: Enable the usage of blobs.Werner Zeh
Since microcode was moved to 3rdparty/blobs, we need to select USE_BLOBS in Kconfig to get the submodule 3rdparty/blobs automaticaly. Change-Id: I25e574fd90b830448cacccd16d01a5a2dbc8517d Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: http://review.coreboot.org/11764 Tested-by: build bot (Jenkins) Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2015-09-07intel: Do not hardcode the position of mrc.cacheAlexandru Gagniuc
The reason for hardcoding the position of the MRC cache was to satisfy the alignment to the erase size of the flash chip. Hardcoding is no longer needed, as we can specify alignment directly. In the long term, the MRC cache will have to move to FMAP, but for now, we reduce fragmentation in CBFS. Note that soc/intel/common hardcoding of mrc.cache is not removed, as the mrc cache implementation there does not use CBFS to find the cache region, and needs a hardcoded address. Change-Id: I5b9fc1ba58bb484c7b5f687368172d9ebe625bfd Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/11527 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2015-09-04mc_tcu3: Adjust gpio settingsWerner Zeh
Adjust gpio settings due to hardware change. Change-Id: I4f493e5f46cbb9919c5b1a8ba294f8c34a07069a Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: http://review.coreboot.org/11489 Tested-by: build bot (Jenkins) Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2015-09-03mc_tcu3: Extend hwinfo.hex and remove version.hex.Werner Zeh
1. Update hwinfo.hex (add dummy data and update checksums). 2. Delete version.hex from mainboard directory. It can be added in site-local if needed. Change-Id: I7af9c4a5f606b96177a8ed4e3edf52535f2f1ec7 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: http://review.coreboot.org/11484 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2015-07-04Kconfig: Fix references to obsolete symbolsMartin Roth
These are all Kconfig symbols that have been removed or renamed. USE_PRINTK_IN_CAR was removed in commit 8c4f31b3 Drop the USE_PRINTK_IN_CAR option. It's a bogus decision... DYNAMIC_CBMEM was removed in commit e2b0affd Remove Kconfig variable that has no effect MAINBOARD_HAS_BOOTBLOCK_INIT was removed in commit 342535cc Remove Kconfig variable that has no effect CACHE_ROM was removed in commit 4337020b Remove CACHE_ROM. SMM_MODULES was removed in commit 44cbe10f smm: Merge configs SMM_MODULES and SMM_TSEG INCLUDE_MICROCODE_IN_BUILD was removed in commit eb73a218 soc/fsp_baytrail: Fix use of microcode-related Kconfig variables CAR_MIGRATION was removed in commit cbf5bdfe CBMEM: Always select CAR_MIGRATION REQUIRES_BLOB was removed in commit 70c85eab build system: Retire REQUIRES_BLOB CPU_MICROCODE_IN_CBFS was renamed to SUPPORT_CPU_UCODE_IN_CBFS in commit 66e0c4c8 - cpu: Rename CPU_MICROCODE_IN_CBFS to SUPPORT_CPU_UCODE_IN_CBFS CONSOLE_SERIAL_UART was renamed to CONSOLE_SERIAL in commit afa7b13b uart: Redefine Kconfig options CONSOLE_SERIAL8250MEM was renamed to DRIVERS_UART_8250MEM in commit afa7b13b - uart: Redefine Kconfig options Change-Id: I8952ca8c53ac2e6cec5f9c77d2f413f086bfab9d Signed-off-by: Martin Roth <gaumless@gmail.com> Reviewed-on: http://review.coreboot.org/10766 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2015-07-02Move baytrail & fsp_baytrail to the common IFD interface.Martin Roth
- Add the common/firmware subdir to the baytrail & fsp_baytrail makefiles and remove the code it replaces. - Update baytrail & fsp_baytrail Kconfigs to use the common code. - Update the IFD Kconfig help and prompts for the TXE vs ME. - Whittle away at the CBFS_SIZE defaults. All the fsp_baytrail platforms have their own defaults. Change-Id: I96a9d4acd6578225698dba28d132d203b8fb71a0 Signed-off-by: Martin Roth <gaumless@gmail.com> Reviewed-on: http://review.coreboot.org/10647 Tested-by: build bot (Jenkins) Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2015-06-27Kconfig: Remove unnecessary and incorrect MRC_CACHE symbolsMartin Roth
Because of a misunderstanding of how Kconfig files are parsed, the OVERRIDE_MRC_CACHE_LOC symbol was added to make sure that the value was correctly set. This is not needed unless for some reason the Kconfig parser is suddenly rewritten to parse everything differently. At some point, the value in the FSP's Kconfig file was updated to OVERRIDE_CACHE_CACHE_LOC, while the entries in the mainboard Kconfig files were not updated. This resulted in the default values not getting set correctly by default on the FSP Bay Trail boards. This removes the whole bunch of incorrect and unnecessary symbols and just sets the default for the MRC cache location directly. Change-Id: I1cec758576866b7e0677272b8309bfde8d4a1ee4 Signed-off-by: Martin Roth <gaumless@gmail.com> Reviewed-on: http://review.coreboot.org/10611 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2015-06-08Remove empty lines at end of fileElyes HAOUAS
Used command line to remove empty lines at end of file: find . -type f -exec sed -i -e :a -e '/^\n*$/{$d;N;};/\n$/ba' {} \; Change-Id: I816ac9666b6dbb7c7e47843672f0d5cc499766a3 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: http://review.coreboot.org/10446 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2015-06-05device_ops: add device_t argument to acpi_inject_dsdt_generatorAlexander Couzens
`device_t device` is missing as argument. Every device_op function should have a `device_t device` argument. Change-Id: I3fc8e0339fa46fe92cc39f7afa896ffd38c26c8d Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Reviewed-on: http://review.coreboot.org/9597 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-02 16:44:31 +0000