| Age | Commit message (Collapse) | Author |
|---|
|
The mainboards mc_apl{2,4,5,6} use VBOOT for verification and can be in
a recovery state for different reasons. In this case we still want the
MRC cache to be around to avoid the DRAM retraining on every boot.
This patch enables the Kconfig switch HAS_RECOVERY_MRC_CACHE which makes
the already available MRC recovery region in FMAP useable.
Test=Boot mc_apl2 in recovery mode and make sure the recovery MRC
cache is used.
Change-Id: I2ea4993f05dd87a0e637f55e84b4fc06f5e29ecc
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
With latest hardware revision only PCIe RP2 and RP7 are used on this
mainboard.
Change-Id: I7702c2b9058dde1c819cb1df8a68fd602f5997da
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With latest hardware revision SATA interface is no longer used on this
mainboard. The mainboard is still in development and not yet released
and for this reason there may still be adjustments.
Change-Id: Icbf088ce4c907e207f6f5d11b8bf5556fe2c90d6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Aggressive Link Power Management are no longer supported on these
mainboards and must therefore be disabled. This feature can have a
negative impact on the real-time behavior of the systems.
TEST:
- Boot into system software on mc_apl1
Change-Id: I8b08381743018790a20273ea1f61e5b0a56e6015
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
In order to guarantee data integrity an expired TCO must not hard reset
the board. Select the Kconfig switch to prevent this reset.
Change-Id: I04080c6bcd486e3a406438cc7a703165bb6945a0
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The only option to make HECI1 function disable on Elkhart Lake SoC
platform is using SBI under SMM mode.
List of changes:
1. Drop `HeciEnabled` from dt and dt chip configuration.
2. Replace all logic that disables HECI1 based on the `HeciEnabled`
chip config with `DISABLE_HECI1_AT_PRE_BOOT` config.
Mainboards that choose to make HECI1 enable during boot don't override
`heci1 disable` config.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I76c625e6221fdef1343599e7dbc7739caa91bf98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sheng Lean Tan <sheng.tan@9elements.com>
|
|
Found using:
diff <(git grep -l '#include <console/console.h>' -- src/) <(git grep -l 'console_time_report\|console_time_get_and_reset\|do_putchar\|vprintk\|printk\|console_log_level\|console_init\|get_log_level\|CONSOLE_ENABLE\|get_console_loglevel\|die_notify\|die_with_post_code\|die\|arch_post_code\|mainboard_post\|post_code\|RAM_SPEW\|RAM_DEBUG\|BIOS_EMERG\|BIOS_ALERT\|BIOS_CRIT\|BIOS_ERR\|BIOS_WARNING\|BIOS_NOTICE\|BIOS_INFO\|BIOS_DEBUG\|BIOS_SPEW\|BIOS_NEVER' -- src/) |grep "<"
Change-Id: I9116965512a5b3241fd7e28537d96637008b31e4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Run the command below to fix all occurrences.
$ git grep -l 'ramstage\*/' | xargs sed -i 's,ramstage\*/,ramstage */,'
Change-Id: Ied155d325846fc0ef3e823e5708c6f74e3d7998f
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Reuse the options from Kconfig.name for variant-specific selects.
Change-Id: I35f51756180882d019a3ea8c555ccd18cd588f44
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Enable TPM init in bootblock so that all further stages and other CBFS
files are directly measured into PCRs immediately instead of being
logged into a buffer and replayed to the TPM in ramstage.
Change-Id: Ib3ac29aa72abe8e967660ae7e8416aeb8812de26
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
This board does not have a LPC or eSPI connection to the NC FPGA anymore
and therefore IO port 0x80 is not useable for POST codes anymore. Enable
the feature of sending the POST codes to the NC FPGA via PCI so that the
POST codes are visbile again in coreboot.
Change-Id: I9043e4ec9a2ad6b946e373bb3dce9da3d42d00d1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
With latest hardware revision all clock outputs will be used on this
mainboard. For this reason set all clock source mappings to
'PCIE_CLK_FREE' to have a free running clock.
Change-Id: Ic3f6fb4e24128742ed72dade7a4555c39fb722ae
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
HECI #2 is not used for CSE communication. Therefore, it is not
necessary to set the parameter 'Heci2Enable' in devicetree.
Change-Id: I7012e4d877a464699727ca775af3f9965e0602e9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The `find_resource` function will never return null (will die instead).
In cases where the existing code already accounts for null pointers, it
is better to use `probe_resource` instead, which returns a null pointer
instead of dying.
Change-Id: I329efcb42a444b097794fde4f40acf5ececaea8c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lance Zhao
|
|
All the mainboard variants of mc_ehl do not use the external switches
for the bypass rails. Disable the matching UPDs and all the low power
modes of the PMC.
Change-Id: I08f4effe5c4d5845bed01dfe1bd1251c58012b7f
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58895
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to get a reliable real-time performance disable all P-States
for all mc_ehl based mainboard.
Change-Id: I22857cc0f1476483ca82c1c872e4519e4b350ea9
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Disable all C-states other than C0/C1 for CPU and package.
Change-Id: I2c163f859dab4b0dc02896c70122e993cdd3db72
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
There are a bunch of devices in the devicetree that are disabled in
FSP-S and not used on this board. Having them around in the devicetree,
even if disabled, is not necessary and leads to a message in the log
(left over static devices...check your devicetree).
This commit cleans up devicetree.cb and removes all unused and disabled
devices.
Change-Id: I7486f9ba362c80b43b6c888a3b40a4c947218299
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58887
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As a prevention of Row-Hammer attacks enable the FSP-M parameter
'RhPrevention'.
Change-Id: I52f68525e882aee26822d9b3c488639c00f27d17
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This configures GPIO GPP_G5 as an input pin for SD card detect.
Change-Id: I708eb112fa054f2f88857001c409fb62493b6206
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
PCIe root ports #4 (00:1c.3) and #6 (00:1c.5) are currently not used on
this mainboard and are not routed either, so remove them from the
devicetree completely. PCIe root port #7 (00:1c.6) is connected and
used. Add the missing settings for L1 substates and latency reporting to
disable these features for this port as well.
Change-Id: I47e8528bea993ed527a0aecdbc93b94bbd9a7a49
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
On mc_ehl2 there are currently four of the six PCIe clocks used to drive
PCIe devices. None of the used clock output is dedicated to a special
device. Therefore do not use a port mapping of the clocks to avoid a
stopping clock once a device is missing and the matching root port is
disabled. Instead set the mapping to 'PCIE_CLK_FREE' to have a free
running clock.
In addition, use the defined constant 'PCIE_CLK_NOTUSED' instead of the
value 0xFF to disable the CLKREQ-feature and unused clocks.
Change-Id: I81419887b7f463a937917b971465245c1cb46b94
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
|
|
On mc_ehl1 there are three of the 6 PCIe clocks used to drive PCIe
devices. None of the used clock output is dedicated to a special device
(CLK0 drives several devices on the mainboard, CLK1 and CLK2 are
connected to a PCIe switch). Therefore do not use a port mapping of the
clocks to avoid a stopping clock once a device is missing and the
matching root port is disabled. Instead set the mapping to
'PCIE_CLK_FREE' to have a free running clock.
In addition, use the defined constant 'PCIE_CLK_NOTUSED' instead of the
value 0xFF to disable the CLKREQ-feature and unused clocks.
Change-Id: I2beea76ff8fefd79f476bef343d13495b45cdfcf
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58740
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PCIe root ports #5 (00:1c.4) and #6 (00:1c.5) are not used on this
mainboard and are not routed either, so remove them from the devicetree
completely. PCIe root port #7 (00:1c.6) is connected and used. Add the
missing settings for L1 substates and latency reporting to disable these
features for this port as well.
Change-Id: I06f59f0369ffcd958b5fe12bb3c646d37103811f
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58568
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are a bunch of devices in the devicetree that are disabled in
FSP-S and not used on this board. Having them around in the devicetree,
even if disabled, is not necessary and leads to a message in the log
(left over static devices...check your devicetree).
This commit cleans up devicetree.cb and removes all unused and disabled
devices.
Change-Id: Ia5ffb382e3524e61b8583aca801063942fe2f247
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The `SMBIOS_PROVIDED_BY_MOBO` Kconfig option is already selected through
the `SECUNET_DMI` option. So, there's no need to select both of them.
Change-Id: I784df87893043a011906af8808aff27d636c7626
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58625
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct the PCH serial IO settings, suitable for this mainboard.
Change-Id: I3c9915b2d52fbc6a15ac1e68c77bfb3983f7b1cd
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Correct the USB settings, suitable for this mainboard.
Change-Id: I691d91d2a76e27b8efdc18eeae737a78e9ae38fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Correct the remaining PCI devices, differing from the ehl1 mainboard.
Change-Id: I8112fa5ea86e879741061798530150701b759156
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard has its own coreboot ready LED. The LED is switched
on via GPIO GPP_F20.
Change-Id: I3570d691e90d2cb6e11b856b876f0327da118522
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Since the DRAM population is fixed to both channels on all mc_ehl boards
there is no need to have this 'half_populated' variable at all.
Simply use a fixed 'false' in the call of 'memcfg_init()' and delete
this variable here.
Change-Id: I783c17e6d92322a8b0c094cce803108e718011fa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
The preferred location for the SPD data on mc_ehl based boards is the
HW-Info data structure. Inside this structure there is a field of 128
bytes available for the SPD data. So in order to use it construct a
buffer in memory which is 256 bytes long (as FSP requests minimum 256
bytes for the SPD data) and where the upper 128 bytes are taken from
HW-Info holding the needed timing parameters for LPDDR4.
If there is a case where HW-Info is not accessible or where the
contained SPD data is not valid (by checking the CRC in HW-Info SPD)
fall back to fixed SPD data set in CBFS.
Change-Id: I2b6a1bde0306ba84f5214b876eaf76ca12d8f058
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
On this mainboard there is a legacy PCI device, which is connected to
the PCIe root port via a PCIe-2-PCI bridge. This device only supports
legacy interrupt routing. For this reason, we have to adjust the PIR8
register (0x3150) which is responsible for PCIe device 25h. The bridge
is connected to PCIe root port 7.
The following routing is required:
INTA#->PIRQC#, INTB#->PIRQD#, INTC#->PIRQA#, INTD#-> PIRQB#
TEST:
- Boot into system software
Change-Id: Id6bb8d00458c4d1e3fefd01ac3848078355868d9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
In upcoming patches, we need mainboard specific adjustments.
Change-Id: Icf9d829b19b2d26a39ad34be4658064083e9da6d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Enable LPC ComB on this mainboard.
TEST:
- Boot Linux and check with 'dmesg | grep tty'
Change-Id: I7ec58685a723c177df18144011934b206e6425d0
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard uses an eSPI-to-LPC bridge for console output. For this
reason, the internal LPSS UART must be disabled.
Change-Id: I86777cf719def331f4d257ddd94e9a87125ebce8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Set the GPIOs according to the circuit diagram for this mainboard.
Change-Id: I19dc24a16ee9f533b45879bf60fb441e24018cc8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard has only SATA Port 1 available with no device sleep
feature.
Change-Id: I338833f2f9bcb407599cfc676ead0b8a9d7379bd
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard has SD slot available and therefore it should be enabled.
Change-Id: I0c97e2dc589bf6b89713a473925e42a20278f457
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This board has the RTC RX6110SA connected to the I2C2 instead of SMBus
as in mc_ehl1. Set the bus speed for I2C2 to 100 kHz, since this RTC
only supports the standard speed.
TEST:
- Console Log shows no errors for RX6110SA during I2C2 init
- Finalize device for I2C 00:32 shows correct date and time
Change-Id: I679c6397fa0d213a25eebaf8a9e0bda9941acd26
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Since this variant uses different DDR4 devices compared to mc_ehl1 in a
memory down configuration, the SPD data file must be adapted.
In a first configuration we use Micron MT53D512M32D2NP modules.
Following values were adjusted according to this board characteristic
and with help of Serial Presence Detect (SPD) for LPDDR3 and LPDDR4
SDRAM Modules JEDEC Spec and the Specification for this Micron modules
itself:
- SPD Byte 4 - only 4Gb density instead of 8Gb for mc_ehl1
- SPD Byte 5 - different Row and Column Address Bits
- SPD Byte 29/30 - 4Gb LPDDR4 needs 130ns tRFCab
- SPD Byte 31/32 - 4Gb LPDDR4 needs 60ns tRFCpb
Change-Id: Icb25f418952f0c96117140863d0d9c897d814ac5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
There are currently two variants for mc_ehl where different UARTs are
used for the console. Move the Kconfig switch UART_FOR_CONSOLE to the
Kconfig of the variant and select the matching value there.
Change-Id: I7152013a0e32ff151b92932a47953705e591dc0d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58052
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a new variant of the mc_ehl board called mc_ehl2. This patch just
copies the files and renames things where needed.
Following patches will adapt the needed features for this new variant.
Change-Id: I3ec3c091017fd66fe6a09216203cdc7c9e833846
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Enable LPSS UART for coreboot console on mc_ehl1.
Change-Id: Id995953741d48fbbe2482ff7c0ef81cac5a31207
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Specify the type of the `DIMM_SPD_SIZE` Kconfig symbol once.
Change-Id: I619833dbce6d2dbe414ed9b37f43196b4b52730e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Since all mainboards use `CHIPSET_LOCKDOWN_COREBOOT`, make it the
default by changing its enum value to 0 and remove its configuration
from all related devicetrees.
If `common_soc_config.chipset_lockdown` is not configured with
something else in the devicetree, then `CHIPSET_LOCKDOWN_COREBOOT`
is used.
Also, add a release note for the upcoming 4.15 release.
Change-Id: I369f01d3da2e901e2fb57f2c83bd07380f3946a6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: I8c5d6686bf7c694f9d594e3801c79cfd7fb3da80
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56342
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some legacy devices need to have the master bit set in the PCI config
due to old drivers not setting it correctly. Set the master bit if the
feature is enabled via Kconfig switch PCI_ALLOW_BUS_MASTER_ANY_DEVICE.
For now, the PCI devices with the ID 110a:403e and 110a:403f needs this
master bit to be set.
Change-Id: Id3f6bda97e5f47d0613a1db8f8adac0b158ab8b1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56632
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Boards based on mc_ehl have, just like some mc_apl variants, legacy
devices on the PCI bus which take longer to boot. In order to ensure
that they will be enumerated correctly wait for them to come up before
PCI scan starts.
TEST=Checked that the new message is visible in the log.
Change-Id: If2f935b69ddaa9364566deacfada5e7d41fcdabd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56631
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Latency Tolerance Reporting is yet another PCIe power management feature
which can have a bad influence on realtime performance. Disable this
feature for all PCIe root ports.
Change-Id: I38023e095ca55efd2178ad944f651fee1f1c34cd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
L1 substates of a PCIe link are meant to save some power when the link
is not active but have the drawback that the PCIe latency is increased
as PLLs are switched on and off as needed.
In order to get a better realtime performance, disable all substates for
every PCIe root port.
Change-Id: Ic5bc8410709d0f0094810bc11a7723e88c30e397
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This variant uses I210 MACPHYs so enable the I210 driver in order to set
the needed MAC addresses. In addition add the function to retrieve a
valid MAC address for the given MACPHY.
Change-Id: Id1d59349db1b86cfdd71bbe27577c0530e8f0b51
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56567
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All the boards based on the mc_ehl baseboard have the NC-FPGA available.
Enable the appropriate driver on baseboard level.
Change-Id: I40b76a837b7ddb70ceba3135996b1c1080170c4d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56566
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All variants based on mc_ehl will use the Siemens HWILIB. Select the
Kconfig switch on baseboard level.
Change-Id: I940f84a4a7449487fe78c793f8dbb1c1b49fa54b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56565
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable IBECC for mc_ehl1 to provide a memory failure protection.
Change-Id: If8f81d6bacb77dc38e231c1cedf22831de8a38a9
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56564
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In favor of better realtime performance disable dynamic frequency
support in the System Agent for mc_ehl1.
Change-Id: I0e62bcf2e5efa97d89bf7192f1536747a02ad992
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56563
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable measured boot for all boards based on mc_ehl baseboard.
Change-Id: I3aff943305c024d1f25d2127e6f60495828da3eb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
All the boards based on the mc_ehl baseboard have a TPM which is
connected to SPI but mapped into the address space of the x86 so that
it acts like a LPC attached TPM. Enable the TPM driver so that it will
be used. In addition add the needed entry in devicetree.
Change-Id: I301d0ed4a108bac45d95eced120e7ba280945d9c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
All the mainboards based on mc_ehl use the external RTC RX6110SA.
Enable the driver in Kconfig for all boards based on mc_ehl. In
addition, as mc_ehl1 has the RTC attached to the SMBus, add the
devicetree entry on behalf of the SMBus device 00:1f.4 for this variant.
Change-Id: Ie1f45d0e6f9063c00253fe58a6268d40de91cf63
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56523
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `VARIANT_DIR` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: Iea2f992a59e41e00fec3cdc9d6a13b5f3ab0a437
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56558
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `FMDFILE` Kconfig symbol once instead of doing
so on each and every mainboard.
Change-Id: I810bd3fe8d42102586db6c2c58b7037a60189257
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56557
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `DEVICETREE` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: If68f11a5ceaa67a3e8218f89e1138c247ebb9a25
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56555
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `MAINBOARD_PART_NUMBER` Kconfig symbol once
instead of doing so on each and every mainboard.
Change-Id: I3692f9e82fe90af4d0da1d037018a20aa1b45793
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56554
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `MAINBOARD_DIR` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: If1cc538b0c4938dac193699897b690e402b3c1e8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56553
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's no need to specify the type of the `CBFS_SIZE` Kconfig symbol
more than once. This is done in `src/Kconfig`, along with its prompt.
Change-Id: I9e08e23e24e372e60c32ae8cd7387ddd4b618ddc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56552
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Provide a valid GPIO configuration based on the mainboard wiring.
Change-Id: I36f0e8292a405b4bac74fbc5fde62e5e414387e7
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56519
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since there is no SD card interface on this mainboard do not set the
card detect GPIO.
Change-Id: Ibe6799c5c540538f97d1726ec16e79f3edbb16fd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56489
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the Kconfig switch PCI_ALLOW_BUS_MASTER_ANY_DEVICE instead of
PCI_ALLOW_BUS_MASTER to enable PCIe bus master bit as requested in
CB:56441 during review.
Change-Id: I433dbae0d9b15e41d1d0750298868341ce3d6b46
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Since this mainboard does not use GSPI at all, disable all GSPI ports.
Change-Id: I60254e9f4047537d86c972151ec9e33552332959
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56488
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard uses I2C1 and I2C4 buses only. Disable all the others as
they are not connected at all.
Change-Id: I4743f6ea6b9a9987ad63b60f56ee9a597a08284b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Features like DevSLP and Aggressive Link Power Management are not
supported on this mainboard and are therefore disabled.
Change-Id: I3bc650ea78be8587889fb7abfe7075cd9a122198
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This board does not use CLKREQ-signaling for PCIe, so disable the pin
assignments. In addition only three clock outputs are used for PCIe,
therefore disable all others to improve EMI.
Change-Id: I545f890fa55a109df7f44d2c82170874fb769009
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56455
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are in total three USB ports that are used on mc_ehl1:
- Port 1: Type A connector connected to USB2/USB3 port 0
- Port 2: Type A connector connected to USB2/USB3 port 1
- Onboard: connected to USB2 port 2
None of the ports supports overcurrent reporting.
Adjust the appropriate UPDs in devicetree to match the hardware
configuration.
Change-Id: I220637b8e9f03efccacd0955e82cfc0c7a6f53ee
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56454
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since mc_ehl1 does not have a display attached nor have a display
connector available (pure headless design), remove display related
settings from the devicetree.
Change-Id: Id31c09fcfba15f55eed19134bd0c2fb887bd2478
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56453
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Take Kconfig switch PCI_ALLOW_BUS_MASTER into account and set the PCI
bus master bit for legacy devices only if it is allowed.
Change-Id: I7798a767d528419bb093f301140ab68cc8b9c5ae
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Since the variants can have different memory move the SPD related
content to the variant directory.
Change-Id: I38aa5e7514437bfcc61c38d64f0ba6f19350810d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56036
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SaGv is only available on ULT/ULX processors, which use PCH-LP. Given
that the Siemens Chili board selects `SOC_INTEL_CANNONLAKE_PCH_H`, it
does not use ULT/ULX processors, and thus does not support SaGv. Drop
the `SaGv` setting from the devicetrees, as it has no effect.
Change-Id: I5be518cce08206ad149efd1665e44a7111b24202
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56205
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, internal flashing is not possible due to FSP lockdown. Thus
let coreboot do chipset lockdown.
Change-Id: Iee4f6986e5edfe1bf6c84fe132bcb47b15bb81f5
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56198
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is a 16 MB flash chip on mc_ehl. Set the ROM size accordingly and
provide a flashmap for partitioning. Select the used flashmap on variant
level to allow different layouts for different variants.
Change-Id: I694729ad98f91e27308220903c49e7cb7fc436b4
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Remove Kconfig switches that are not needed for mc_ehl based mainboards.
Change-Id: If231f37f06c6763d52a821799e87fdb3010af0aa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56034
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
There will be more variants of this mainboard so prepare the scheme for
Kconfig to handle the variants properly.
Change-Id: If1cf418836d77a45955ee55d30ba670db8ff2533
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Add a new mainboard called mc_ehl which is based on Intel's
'elkhartlake_crb'. This commit simply copies the mainboard directory and
adjusts the naming to match the new board's name. Follow-up commits will
introduce the needed changes for the new mainboard.
Change-Id: Ia7c0616098046d975aa698910ac81f435d7882cb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56032
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
New kconfig parsers interpret $(var) themselves, leading to empty
fields. Old kconfig understands \$(var), so use that.
Change-Id: I927fc9dc7a66211bfe51d4324cf7c51b555ea3a8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55912
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Only I2C controller 3 is used on this mainboard. Disable all other
controllers.
Change-Id: Id06d98787a0574a5b3a8dc2e86858dfcc7154606
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
The I2C bus at which the external RTC is attached to is operated at
standard speed (100 kHz) at coreboot runtime. The OS can choose to run it
at fast speed since it uses its own driver and controller setup.
Report additional bus timings for fast mode so that OS can do it right.
Change-Id: I82e11e5dde8ad1047713f105c5a6d020eebf1ffd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55089
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Already released Linux versions did not have the needed ACPI-extension
in the RTC driver. If the ACPI-Support is enabled for the RTC, this
older Linux will not be able to use this device as it will be claimed by
the PNP-drivers. As there is no way to avoid that an older Linux kernel
meets a newer coreboot in the field, we need to disable the ACPI
support for the RTC for the mc_apl-based mainboards.
Change-Id: I9f9939ba3234dc3654a4ef8a498649453941ebdf
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55004
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Variant mc_apl1 is the only one that uses gpio.c from baseboard. For
this reason, gpio.c is moved from baseboard to mc_apl1.
Change-Id: Ie2ba8181dfe887df9abbbd648f2cbdc6ffc65530
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
With commit 405f229689 (soc/intel/*: drop UART pad configuration from
common code) the UART pad configuration was dropped from common SoC
code. Through a second commit 5ff17ed393 (mb/siemens/mc_apl1: do UART
pad configuration at board-level) the UART pad configuration was made
for mc_apl1 baseboard. This change is also needed for all other mc_apl
boards.
Change-Id: If78726d9b141e4e7580cca3267f49c1a5b95d7fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The CMOS option system does not support negative integers. Thus, retype
and rename the option API functions to reflect this.
Change-Id: Id3480e5cfc0ec90674def7ef0919e0b7ac5b19b3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
All the boards in the patch have a constraint for the I2C bus to operate
on 100 kHz. Provide dedicated values for rise time, fall time and data
hold time on mainboard level to get a proper timing which takes the bus
load into account. Giving these values the driver computes the needed
timings correctly.
TEST=Measure I2C frequency on all boards while coreboot accesses
external RTC and make sure it is 100 kHz.
Change-Id: Iab634190bda5fa2a4fdf2ebaa1e45ac897d84deb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52721
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All related mainboards are setting DIMM_SPD_SIZE to 512. Therefore,
default to 512 in the SoC Kconfig and drop it from related mainboard
Kconfigs.
Change-Id: Idb6a0e42961eeb490afd76b4aa7d940961991733
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52513
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9273b90b6a21b8f52fa42d9ff03a9b56eec9fcbf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I14ec7d6faa20542707a1b6041e1ce358ce4a537a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: I6e0f33172fbcecebddfccdf64c22685636a23936
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50524
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I37f12f5cb35ea1a6ad33edb114688ce1619030a4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
With a new HW revision of this board, the connection of the external RTC
RX6110SA was changed from I2C bus 0 to I2C bus 3.
Change-Id: I10dd44949973ea490b3c7e4ad83d56ce2e566adf
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Iac8a6e386b708ae5c4dbf0677bfe05f1358bf8fd
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49442
Tested-by: siemens-bot
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Objects that are created with acpigen need to be declared
with External () for the generation of dsdt.asl to pass
iasl without errors.
There are some objects that are common to all platforms,
and some that should be declared only conditionally.
Having a top-level ASL helps to achieve this.
Change-Id: Ibaf1ab9941b82f99e5fa857c0c7e4b6192c74330
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to a bootblock gpio table for the board as a
first step. Common UART pad config code then gets dropped in CB:48829.
Change-Id: Iad40b6315a29e7aea612a3e1a169372d296d1d6c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49443
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Until now some FSP-S parameters were configured for Siemens APL
mainboards via the Binary Configuration Tool (BCT). For simplification,
the original APL FSP binary should now be used. For this purpose, the
corresponding FSP-S parameters are set via devicetree, respectively via
mainboard_silicon_init_params accordingly.
The following parameters are affected:
- Disable CPU power states (C-states)
- Set lowest Max Pkg Cstate - PkgC0C1
- Disable PCIe Hot Plug for all enabled RPs
- Disable PCIe Transmitter Half Swing for all RPs
- Disable PCIe Active State Power Management (ASPM) for all RPs
- Disable PCIe L1 Substates for all RPs
TEST:
- Compare old with new coreboot log on mc_apl5, found no differences
- Boot Linux v4.4 and check output of 'lspci'
Change-Id: I5af627defd6426140cc9a74bb18db400a8971d72
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
